AD OP11

Quad Matched
741-Type Operational Amplifiers
OP11
PIN CONFIGURATION
Guaranteed VOS: 500 μV maximum
Guaranteed matched CMRR: 94 dB minimum
Guaranteed matched VOS: 750 μV maximum
LM148/LM348 direct replacement
Low noise
Silicon-nitride passivation
Internal frequency compensation
Low crossover distortion
Continuous short-circuit protection
Low input bias current
OUT A 1
14 OUT D
–IN A 2
13 –IN D
+IN A 3
V+ 4
12 +IN D
OP11
11 V–
+IN B 5
10 +IN C
–IN B 6
9 –IN C
OUT B 7
8 OUT C
02784-001
FEATURES
Figure 1. 14-Lead PDIP (N-14)
(P Suffix)
GENERAL DESCRIPTION
The OP11 provides four matched 741-type operational
amplifiers in a single 14-lead PDIP. The OP11 is pin compatible
with the LM148, LM348, RM4156, RM4158, and HA4741
amplifiers. The amplifier is matched for common-mode
rejection ratio and offset voltage, which is very important in
designing instrumentation amplifiers. In addition, the amplifier
is designed to have equal positive-going and negative-going
slew rates, which is an important consideration for good audio
system performance.
The OP11 is ideal for use in designs requiring minimum space
and cost while maintaining performance.
V+
–IN
+IN
02784-003
OUTPUT
V–
Figure 2. Simplified Schematic
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2007 Analog Devices, Inc. All rights reserved.
OP11
TABLE OF CONTENTS
Features .............................................................................................. 1
Matching Characteristics..............................................................4
General Description ......................................................................... 1
Absolute Maximum Ratings ............................................................5
Pin Configuration............................................................................. 1
ESD Caution...................................................................................5
Revision History ............................................................................... 2
Typical Performance Characteristics ..............................................6
Specifications..................................................................................... 3
Outline Dimensions ..........................................................................9
Electrical Characteristics............................................................. 3
Ordering Guide .............................................................................9
REVISION HISTORY
6/07—Rev. A to Rev. B
Updated Format..................................................................Universal
Deleted 14-Lead Hermetic DIP/CERDIP .......................Universal
Changes to Table 1............................................................................ 3
Deleted Table 3; Renumbered Sequentially .................................. 3
Changes to Table 2, Layout, Table 3, and Table 4 ......................... 4
Changes to Table 5 and Table 6....................................................... 5
Changes to Figure 17........................................................................ 8
Updated Outline Dimensions ......................................................... 9
Changes to Ordering Guide ............................................................ 9
4/02—Rev. 0 to Rev. A
Change OP-09/OP-11 to OP11..............................................Global
Edits to Pin Connections................................................................. 1
Edits to Figure 1 ................................................................................ 1
Edits to Absolute Maximum Ratings ............................................. 2
Edits to Ordering Guide .................................................................. 2
Edits to Spec Tables .......................................................................2-4
Deletion of Dice Characteristics..................................................... 5
Deletion of Wafer Test Limits Table ............................................... 5
Deletion of Typical Electrical Characteristics Table .................... 5
Rev. B | Page 2 of 12
OP11
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VS = ±15 V, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
Input Offset Voltage
Input Offset Current
Input Bias Current
Input Resistance Differential Mode 1
Input Voltage Range
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Output Voltage Swing
Large Signal Voltage Gain
Power Consumption 2
Input Noise Voltage
Input Noise Voltage Density
Symbol
VOS
IOS
IB
RIN
IVR
CMRR
PSRR
VO
AVO
Pd
en p-p
en
Input Noise Current
Input Noise Current Density
In p-p
In
Channel Separation
Slew Rate 3
Large Signal Bandwidth3
Closed-Loop Bandwidth 4
Rise Time3
Overshoot3
CS
SR
BW
tf
OS
Conditions
RS ≤ 10 kΩ
VCM = ±12 V, RS ≤ 10 kΩ
VS = ±5 V to ±15 V, RS ≤ 10 kΩ
RL = 2 kΩ
RL ≤ 2 kΩ, VO = ±10 V
VO = 0 V
0.1 Hz to 10 Hz
fO = 10 Hz
fO = 100 Hz
fO = 1 kHz
0.1 Hz to 10 Hz
fO = 10 Hz
fO = 100 Hz
fO = 1 kHz
VO = 20 V p-p
AVCL = 1
AV = 1, VIN = 50 mV
1
Guaranteed by input bias current.
Total dissipation for all four amplifiers in package.
Sample tested.
4
Guaranteed by rise time.
2
3
Rev. B | Page 3 of 12
Min
0.17
±12
100
±11
100
100
0.7
11
2.4
Typ
0.3
5.5
180
0.29
±13
120
4
±13
650
105
0.7
18
14
12
17
1.8
1.5
1.2
130
1.0
16
3.0
110
15
Max
0.5
20
300
32
180
145
25
Unit
mV
nA
nA
MΩ
V
dB
μV/V
V
V/mV
mW
μV p-p
nV/√Hz
nV/√Hz
nV/√Hz
pA p-p
pA/√Hz
pA/√Hz
pA/√Hz
dB
V/μs
kHz
MHz
ns
%
OP11
VS = ±15 V, 0°C ≤ TA ≤ 70°C, unless otherwise noted.
Table 2.
Parameter
Input Offset Voltage
Average Input Offset Voltage Drift 1
Input Offset Current
Average Input Offset Current Drift1
Input Bias Current
Input Voltage Range
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large Signal Voltage Gain
Output Voltage Swing
Power Consumption 2
1
2
Symbol
VOS
TCVOS
IOS
TCIOS
IB
IVR
CMRR
PSRR
AVO
VO
Pd
Conditions
RS ≤ 10 kΩ
RS ≤ 10 kΩ
VCM = ±12 V, RS ≤ 10 kΩ
VS = ±5 V to ±15 V, RS ≤ 10 kΩ
RL ≥ 2 kΩ, VO = ±10 V
RL ≥ 2 kΩ
VO = 0 V
Min
±12
100
50
±11
Typ
0.4
2.0
14
0.1
200
±13
120
4
250
±13
115
Max
0.8
10
30
0.3
350
32
200
Unit
mV
μV/°C
nA
nA/°C
nA
V
dB
μV/V
V/mV
V
mW
Guaranteed but not tested.
Total dissipation for all four amplifiers in package.
MATCHING CHARACTERISTICS
VS = ±15 V, TA = 25°C, RS ≤ 100 Ω, unless otherwise noted.
Table 3.
Parameter
Input Offset Voltage Match
Common-Mode Rejection
Ratio Match
Symbol
ΔVOS
ΔCMRR
Conditions
Min
VCM = ±12 V
VCM = ±12 V
94
Conditions
Min
VCM = ±12 V
VCM = ±12 V
94
Typ
0.5
1
120
Max
0.75
20
Unit
mV
μV/V
dB
Typ
0.6
3.2
110
Max
1.0
20
Unit
mV
μV/V
dB
VS = ±15 V, 0°C ≤ TA ≤ 70°C, RS ≤ 100 Ω, unless otherwise noted.
Table 4.
Parameter
Input Offset Voltage Match
Common-Mode Rejection
Ratio Match
Symbol
ΔVOS
ΔCMRR
Rev. B | Page 4 of 12
OP11
ABSOLUTE MAXIMUM RATINGS
Table 5.
Table 6. Thermal Resistance
Parameter
Supply Voltage (VS)
Differential Input Voltage
Input Voltage
Output Short-Circuit Duration
Package Type
14-Lead PDIP (N-14)
Storage Temperature Range
Lead Temperature (Soldering, 60 sec)
Operating Temperature Range
Rating
±22 V
±30 V
Supply Voltage
Continuous
(One Amp Only)
−65°C to +125°C
300°C
0°C to 70°C
1
θJA1
83
θJC
39
Unit
°C/W
θJA is specified for worst-case conditions, that is, θJA is specified for device in
socket for PDIP.
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. B | Page 5 of 12
OP11
TYPICAL PERFORMANCE CHARACTERISTICS
800
–0.1
VS = ±15V
RL = 2kΩ
700
–0.2
600
OPEN-LOOP GAIN (V/mV)
INPUT OFFSET VOLTAGE (mV)
VS = ±15V
–0.3
–0.4
500
400
300
200
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
100
120
140
0
–60
02784-004
–0.5
–60
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
140
120
VS = ±15V
RL = 2kΩ
TA = 25°C
CL = 100pF
VS = ±15V
100
OPEN-LOOP GAIN (dB)
15
10
GAIN
0
45
80
PHASE
60
90
40
135
20
180
PHASE LAG (Degrees)
20
0
–60
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
100
120
140
0
0.1
1
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
02784-008
5
02784-005
10M
Figure 7. Open-Loop Gain and Phase vs. Frequency
Figure 4. Input Offset Current vs. Temperature
1.4
300
NORMALIZED VALUE REFERRED TO 25°C
VS = ±15V
200
100
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
100
120
140
1.2
1.1
SLEW RATE
1.0
0.9
BANDWIDTH
0.8
0.7
0.6
–60
02784-006
0
–60
VS = ±15V
1.3
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
100
120
140
Figure 8. Normalized Slew Rate and Bandwidth vs. Temperature
Figure 5. Input Bias Current vs. Temperature
Rev. B | Page 6 of 12
02784-009
INPUT OFFSET CURRENT (nA)
120
Figure 6. Open-Loop Gain vs. Temperature
Figure 3. Input Offset Voltage vs. Temperature
INPUT BIAS CURRENT (nA)
100
02784-007
100
OP11
800
120
CHANNEL SEPARATION (dB)
700
600
500
400
300
200
100
80
60
40
10
15
POWER SUPPLY VOLTAGE (V)
20
0
10
1k
VS = ±15V
TA = 25°C
VOLTAGE NOISE DENSITY (nV/ Hz)
120
CMRR (dB)
100
80
60
40
20
1
10
100
1k
FREQUENCY (Hz)
10k
100k
10
CURRENT NOISE DENSITY (pA/ Hz)
VS = ±15V
TA = 25°C
60
40
20
10
100
1k
FREQUENCY (Hz)
10k
100k
02784-012
PSRR (dB)
80
1
10k
100
100
0
100
1k
FREQUENCY (Hz)
Figure 13. Voltage Noise Density vs. Frequency
VS = ±15V
TA = 25°C
120
100k
100
Figure 10. CMRR vs. Frequency
140
10k
VS = ±15V
TA = 25°C
1
10
02784-011
0
1k
FREQUENCY (Hz)
Figure 12. Channel Separation vs. Frequency
Figure 9. Open-Loop Gain vs. Power Supply Voltage
140
100
02784-014
5
02784-010
0
02784-013
20
100
0
VS = ±15V
TA = 25°C
10
1
0.1
10
Figure 11. PSRR vs. Frequency
100
1k
FREQUENCY (Hz)
Figure 14. Current Noise Density vs. Frequency
Rev. B | Page 7 of 12
10k
02784-015
OPEN-LOOP GAIN (V/mV)
140
RL = 2kΩ
TA = 25°C
OP11
20
VS = ±15V
TA = 25°C
14
OUTPUT VOLTAGE SWING (V)
OUTPUT VOLTAGE (mV)
16
VS = ±15V
RL = 2kΩ
TA = 25°C
CL = 100pF
0
–20
POSITIVE SWING
NEGATIVE SWING
12
10
8
6
4
200
400
TIME (ns)
600
800
0
0.1
Figure 15. Transient Response
5
TA = 25°C
QUIESCENT CURRENT (mA)
OUTPUT VOLTAGE (V)
2
10
Figure 18. Output Voltage Swing vs. Load Resistance
VS = ±15V
RL = 2kΩ
TA = 25°C
CL = 100pF
3
1
LOAD RESISTANCE TO GROUND (kΩ)
02784-019
0
02784-016
2
1
0
–1
–2
4
3
2
1
2
4
6
8
10
12
TIME (µs)
14
16
18
20
0
0
Figure 16. Voltage Follower Pulse Response
28
(27)
20
30
TOTAL SUPPLY VOLTAGE (V)
40
Figure 19. Quiescent Current vs. Total Supply Voltage
140
VS = ±15V
RL = 2kΩ
TA = 25°C
VS = ±15V
POWER CONSUMPTION (mW)
24
20
16
12
8
130
120
110
0
1k
10k
100k
FREQUENCY (Hz)
1M
100
–60
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
100
120
Figure 20. Power Consumption vs. Temperature
Figure 17. Maximum Output Swing vs. Frequency
Rev. B | Page 8 of 12
140
02784-021
4
02784-018
MAXIMUM OUTPUT SWING (V)
10
02784-020
0
02784-017
–3
OP11
OUTLINE DIMENSIONS
0.775 (19.69)
0.750 (19.05)
0.735 (18.67)
14
8
1
7
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.210 (5.33)
MAX
0.060 (1.52)
MAX
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.110 (2.79)
SEATING
PLANE
0.015 (0.38)
GAUGE
PLANE
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.070 (1.78)
0.050 (1.27)
0.045 (1.14)
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
070606-A
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
Figure 21. 14-Lead Plastic Dual In-Line Package [PDIP]
(N-14)
[P Suffix]
Dimensions shown in inches and (millimeters)
ORDERING GUIDE
Model
OP11EP
OP11EPZ 1
1
Temperature Range
0°C to 70°C
0°C to 70°C
Package Description
14-Lead Plastic Dual In-Line Package (PDIP)
14-Lead Plastic Dual In-Line Package (PDIP)
Z = RoHS Compliant Part.
For military processed devices, refer to the Standard Microcircuit Drawing (SMD) available at
http://www.dscc.dla.mil/downloads/Milspec/Smd/89801.pdf.
SMD Part Number
5962-89801012A
5962-8980101CA
Analog Devices, Inc. Equivalent
OP11ARCMDA
OP11AYMDA
Rev. B | Page 9 of 12
Package Option
N-14 (P-Suffix)
N-14 (P-Suffix)
OP11
NOTES
Rev. B | Page 10 of 12
OP11
NOTES
Rev. B | Page 11 of 12
OP11
NOTES
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C02784-0-6/07(B)
Rev. B | Page 12 of 12