KEMET C114G102B2CG5CA

F-3113 5/06
CERAMIC LEADED CAPACITORS
KEMET Series
Performance Information
MIL-PRF-20
MIL-PRF-39014/01/02/05
MIL-C-11015
Ceramic Leaded Packaging
Page
1-6
C052G/C062G/C114G/
C124G/192G/C202G/C222G
7-12
C052T/C062T/C114T/
C124T/192T/C202T/C222T
13-18
C052K/C062K/C114K/
C124K/192K/C202K/C222K
13-18
19-21
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC LEADED
Ceramic Leaded Capacitors
APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS
ELECTRICAL CHARACTERISTICS
The fundamental electrical properties of multilayer
ceramic capacitors are as follows:
Polarity: Multilayer ceramic capacitors are not polar,
and may be used with DC voltage applied in either direction.
Rated Voltage: This term refers to the maximum continuous DC working voltage permissible across the entire
operating temperature range. Multilayer ceramic capacitors
are not extremely sensitive to voltage, and brief applications
of voltage above rated will not result in immediate failure.
However, reliability will be reduced by exposure to sustained
voltages above rated.
Capacitance: The standard unit of capacitance is the
farad. For practical capacitors, it is usually expressed in
microfarads (10-6 farad), nanofarads (10-9 farad), or picofarads
(10-12 farad). Standard measurement conditions are as
follows:
Class I (up to 1,000 pF):
1MHz and 1.2 VRMS
maximum.
Class I (over 1,000 pF):
1kHz and 1.2 VRMS
maximum.
Class II:
1 kHz and 1.0
0.2 VRMS.
Class III:
1 kHz and 0.5
0.1 VRMS.
Like all other practical capacitors, multilayer ceramic
capacitors also have resistance and inductance. A simplified
schematic for the equivalent circuit is shown in Figure 1.
Other significant electrical characteristics resulting from
these additional properties are as follows:
R
P
Figure 1
R
S
L
C
C = Capacitance
L = Inductance
R = Equivalent Series Resistance (ESR)
S
R = Insulation Resistance (IR)
P
Impedance: Since the parallel resistance (Rp) is normally very high, the total impedance of the capacitor is:
Z=
Where
2
RS + (XC - XL)
2
Z = Total Impedance
RS = Equivalent Series Resistance
XC = Capacitive Reactance =
1
2πfC
XL = Inductive Reactance = 2πfL
The variation of a capacitor’s impedance with frequency
determines its effectiveness in many applications.
Dissipation Factor: Dissipation Factor (DF) is a measure of the losses in a capacitor under AC application. It is the
ratio of the equivalent series resistance to the capacitive reactance, and is usually expressed in percent. It is usually measured simultaneously with capacitance, and under the same
conditions. The vector diagram in Figure 2 illustrates the relationship between DF, ESR, and impedance. The reciprocal of
the dissipation factor is called the “Q”, or quality factor. For
convenience, the “Q” factor is often used for very low values
of dissipation factor. DF is sometimes called the “loss tangent”
or “tangent ␦”, as derived from this diagram.
ESR
Figure 2
O
DF = ESR
Xc
δ
X
c
Ζ
1
Xc =
2πfC
Insulation Resistance: Insulation Resistance (IR) is the
DC resistance measured across the terminals of a capacitor,
represented by the parallel resistance (Rp) shown in Figure 1.
For a given dielectric type, electrode area increases with
capacitance, resulting in a decrease in the insulation resistance. Consequently, insulation resistance is usually specified
as the “RC” (IR x C) product, in terms of ohm-farads or
megohm-microfarads. The insulation resistance for a specific
capacitance value is determined by dividing this product by
the capacitance. However, as the nominal capacitance values
become small, the insulation resistance calculated from the
RC product reaches values which are impractical.
Consequently, IR specifications usually include both a minimum RC product and a maximum limit on the IR calculated
from that value. For example, a typical IR specification might
read “1,000 megohm-microfarads or 100 gigohms, whichever
is less.”
Insulation Resistance is the measure of a capacitor to
resist the flow of DC leakage current. It is sometimes referred
to as “leakage resistance.” The DC leakage current may be
calculated by dividing the applied voltage by the insulation
resistance (Ohm’s Law).
Dielectric Withstanding Voltage: Dielectric withstanding voltage (DWV) is the peak voltage which a capacitor is
designed to withstand for short periods of time without damage. All KEMET multilayer ceramic capacitors will withstand a
test voltage of 2.5 x the rated voltage for 60 seconds.
KEMET specification limits for these characteristics at
standard measurement conditions are shown on page 2.
Variations in these properties caused by changing conditions
of temperature, voltage, frequency, and time are covered in
the following sections.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
1
APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS
TABLE 1
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS I DIELECTRICS
EFFECT OF TEMPERATURE
Tolerance of
Temperature
Coefficient *
0.20
+0.2
Letter
Symbol
Multiplier
Number
Symbol
PPM per
Degree C
Letter
Symbol
0.0
0.3
0.9
1.0
1.5
2.2
3.3
4.7
7.5
C
B
A
M
P
R
S
T
U
-1
-10
-100
-1000
-100000
+1
+10
+100
+1000
+10000
0
1
2
3
4
5
6
7
8
9
3 0
60
120
250
500
1000
2500
G
H
J
K
L
M
N
%∆C
+0.1
PPM per
Degree C
Letter
Symbol
Degree
Celcius
Number
Symbol
+10C
-30C
-55C
Z
Y
X
+45C
+65C
+85C
+105C
+125C
+150C
+200C
2
4
5
6
7
8
9
Percent
-40
-20
0
+20
+40
+60
+80
+100
0.0
+125
Figure 3.
Temperature °C
Capacitance & DF vs Temperature - C0G
+20
8.0
6.0
+10
%∆C
Degree
Celcius
%DF
-0.2
-55
TABLE 2
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS II & III DIELECTRICS
High Temperature Maximum Capacitance
Rating
Shift
0.10
-0.1
* These symetrical tolerances apply to a two-point measurement of
temperature coefficient: one at 25ºC and one at 85ºC. Some deviation
is permitted at lower temperatures. For example, the PPM tolerance
for C0G at -55 is +30 / -72 PPM.
Low Temperature
Rating
%∆C
0
%∆C
0
4.0
%DF
-10
-20
-60
-40
-20
0
+20
+40
+60
2.0
0.0
+80 +100 +120 +140
Figure 4.
Temperature °C
Capacitance & DF vs Temperature - X7R
Letter
Symbol
±1.0%
±1.5%
±2.2%
±3.3%
±4.7%
±7.5%
±10.0%
±15.0%
±22.0%
+22 / -33%
+22 / -56%
+22 / -82%
A
B
C
D
E
F
P
R
S
T
U
V
SPECIFIED ELECTRICAL LIMITS
PARAMETER
Dissipation Factor: Measured at following conditions:
C0G - 1 kHz and 1 vrms if capacitance > 1000 pF
1 Mhz and 1 vrms if capacitance ≤ 1000 pF
X7R - 1 kHz and 1 vrms* or if extended cap range 0.5 vrms
Dielectric Strength: 2.5 times rated DC voltage
2
%DF
Multiplier Applied
to Temperature
Coefficient
TEMPERATURE CHARACTERISTICS
C0G
X7R
0.15%
2.5%
Pass Subsequent IR Test
Insulation Resistance (IR): At rated DC voltage,
or whichever of the two is smaller
1,000 MΩ−µF
or 100 GΩ
1,000 MΩ−µF
or 100 GΩ
Temperature Characteristics: Range, °C
Capacitance Change without DC voltage
-55 to +125
0 ± 30 ppm/°C
-55 to +125
±15%
* 1 MHz and 1 vrms if capacitance ≤ 100 pF on military product.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
%DF
Significant Figure
of Temperature
Coefficient
APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS
% D.F.
% Capacitance Change
EFFECT OF APPLIED VOLTAGE
AC
+10
+5
0
-5
DC
-10
4
3
2
1
AC
DC
0.1
1
10
100
Figure 6.
AC or DC Volts Applied
Typical Effects of 1000 Hz AC and DC Voltage Level on
Capacitance and Dissipation Factor - X7R
Note: C0G Dielectric capacitance and dissipation factor are
stable with voltage.
Effect of Temperature: Both capacitance and dissipation factor are affected by variations in temperature. The maximum capacitance change with temperature is defined by the
temperature characteristic. However, this only defines a “box”
bounded by the upper and lower operating temperatures and
the minimum and maximum capacitance values. Within this
“box”, the variation with temperature depends upon the specific dielectric formulation. Typical curves for KEMET capacitors are shown in Figures 3 and 4. These figures also include
the typical change in dissipation factor for KEMET capacitors.
Insulation resistance decreases with temperature.
Typically, the insulation resistance at maximum rated temperature is 10% of the 25ºC value.
Effect of Voltage: Class I ceramic capacitors are not
affected by variations in applied AC or DC voltages. For Class
II and III ceramic capacitors, variations in voltage affect only
the capacitance and dissipation factor. The application of DC
voltage higher than 5 vdc reduces both the capacitance and
dissipation factor. The application of AC voltages up to 10-20
Vac tends to increase both capacitance and dissipation factor
At higher AC voltages, both capacitance and dissipation factor
begin to decrease.
Typical curves showing the effect of applied AC and DC
voltage are shown in Figure 6 for KEMET X7R capacitors.
Effect of Frequency: Frequency affects both capacitance and dissipation factor. Typical curves for KEMET multilayer ceramic capacitors are shown in Figures 8 and 9.
The variation of impedance with frequency is an important consideration in the application of multilayer ceramic
capacitors. Total impedance of the capacitor is the vector of the
capacitive reactance, the inductive reactance, and the ESR, as
illustrated in Figure 2. As frequency increases, the capacitive
reactance decreases. However, the series inductance (L)
shown in Figure 1 produces inductive reactance, which
increases with frequency. At some frequency, the impedance
ceases to be capacitive and becomes inductive. This point, at
the bottom of the V-shaped impedance versus frequency
curves, is the self-resonant frequency. At the self-resonant frequency, the reactance is zero, and the impedance consists of
the ESR only.
Typical impedance versus frequency curves for KEMET
multilayer ceramic capacitors are shown in Figures 10 and 11.
These curves apply to KEMET capacitors in chip form, without
leads. Lead configuration and lead length have a significant
impact on the series inductance. The lead inductance is
approximately 10nH/inch, which is large compared to the
inductance of the chip. The effect of this additional inductance
is a decrease in the self-resonant frequency, and an increase
in impedance in the inductive region above the self-resonant
frequency.
Effect of Time: The capacitance of Class II and III
dielectrics change with time as well as with temperature, voltage and frequency. This change with time is known as “aging.”
It is caused by gradual realignment of the crystalline structure
of the ceramic dielectric material as it is cooled below its Curie
temperature, which produces a loss of capacitance with time.
The aging process is predictable and follows a logarithmic
decay. Typical aging rates for C0G and X7R dielectrics are as
follows:
C0G
X7R
None
2.0% per decade of time
Typical aging curves for X7R dielectrics is shown in
Figure 12.
The aging process is reversible. If the capacitor is heated to a temperature above its Curie point for some period of
time, de-aging will occur and the capacitor will regain the
capacitance lost during the aging process. The amount of deaging depends on both the elevated temperature and the
length of time at that temperature. Exposure to 150ºC for onehalf hour or 125ºC for two hours is usually sufficient to return
the capacitor to its initial value.
Because the capacitance changes rapidly immediately
after de-aging, capacitance measurements are usually delayed
for at least 10 hours after the de-aging process, which is often
referred to as the “last heat.” In addition, manufacturers utilize
3
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS
the aging rates to set factory test limits which will bring the
capacitance within the specified tolerance at some future time,
to allow for customer receipt and use. Typically, the test limits
are adjusted so that the capacitance will be within the specified
tolerance after either 1,000 hours or 100 days, depending on
the manufacturer and the product type.
POWER DISSIPATION
Power dissipation has been empirically determined for
two representative KEMET series: C052 and C062. Power dissipation capability for various mounting configurations is shown
in Table 3. This table was extracted from Engineering Bulletin
F-2013, which provides a more detailed treatment of this subject.
Note that no significant difference was detected between
the two sizes in spite of a 2 to 1 surface area ratio. Due to the
materials used in the construction of multilayer ceramic capacitors, the power dissipation capability does not depend greatly
on the surface area of the capacitor body, but rather on how
well heat is conducted out of the capacitor lead wires.
Consequently, this power dissipation capability is applicable to
other leaded multilayer styles and sizes.
TABLE 3
POWER DISSIPATION CAPABILITY
(Rise in Celsius degrees per Watt)
Mounting Configuration
Power
Dissipation
of C052 & C062
1.00" leadwires attached to binding post
of GR-1615 bridge (excellent heat sink)
90 Celsius degrees
rise per Watt 10%
0.25" leadwires attached to binding post
of GR-1615 bridge
55 Celsius degrees
rise per Watt 10%
Capacitor mounted flush to 0.062" glassepoxy circuit board with small copper traces
77 Celsius degrees
rise per Watt 10%
Capacitor mounted flush to 0.062" glassepoxy circuit board with four square inches
of copper land area as a heat sink
53 Celsius degrees
rise per Watt 10%
As shown in Table 3, the power dissipation capability of
the capacitor is very sensitive to the details of its use environment. The temperature rise due to power dissipation should not
exceed 20ºC. Using that constraint, the maximum permissible
power dissipation may be calculated from the data provided in
Table 3.
It is often convenient to translate power dissipation capability into a permissible AC voltage rating. Assuming a sinusoidal wave form, the RMS “ripple voltage” may be calculated
from the following formula:
E=Zx
Where
PMAX
R
E = RMS Ripple Voltage (volts)
P = Power Dissipation (watts)
The data necessary to make this calculation is included in
Engineering Bulletin F-2013. However, the following criteria
must be observed:
1. The temperature rise due to power dissipation
should be limited to 20ºC.
2. The peak AC voltage plus the DC voltage must not
exceed the maximum working voltage of the
capacitor.
Provided that these criteria are met, multilayer ceramic
capacitors may be operated with AC voltage applied without
need for DC bias.
RELIABILITY
A well constructed multilayer ceramic capacitor is
extremely reliable and, for all practical purposes, has an infinite life span when used within the maximum voltage and
temperature ratings. Capacitor failure may be induced by sustained operation at voltages that exceed the rated DC voltage,
voltage spikes or transients that exceed the dielectric withstanding voltage, sustained operation at temperatures above
the maximum rated temperature, or the excessive temperature rise due to power dissipation.
Failure rate is usually expressed in terms of percent per
1,000 hours or in FITS (failure per billion hours). Some
KEMET series are qualified under U.S. military established
reliability specifications MIL-PRF-20, MIL-PRF-123, MILPRF-39014, and MIL-PRF-55681. Failure rates as low as
0.001% per 1,000 hours are available for all capacitance /
voltage ratings covered by these specifications. These specifications and accompanying Qualified Products List should
be consulted for details.
For series not covered by these military specifications,
an internal testing program is maintained by KEMET Quality
Assurance. Samples from each week’s production are subjected to a 2,000 hour accelerated life test at 2 x rated voltage
and maximum rated temperature. Based on the results of
these tests, the average failure rate for all non-military series
covered by this test program is currently 0.06% per 1,000
hours at maximum rated conditions. The failure rate would be
much lower at typical use conditions. For example, using MILHDBK-217D this failure rate translates to 0.9 FITS at 50%
rated voltage and 50ºC.
Current failure rate details for specific KEMET multilayer ceramic capacitor series are available on request.
MISAPPLICATION
Ceramic capacitors, like any other capacitors, may fail
if they are misapplied. Typical misapplications include exposure to excessive voltage, current or temperature. If the
dielectric layer of the capacitor is damaged by misapplication
the electrical energy of the circuit can be released as heat,
which may damage the circuit board and other components
as well.
If potential for misapplication exists, it is recommended
that precautions be taken to protect personnel and equipment
during initial application of voltage. Commonly used precautions include shielding of personnel and sensing for excessive
power drain during board testing.
Z = Impedence
4
R = ESR
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS
Figure 12
5
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED AXIAL & RADIAL
PERFORMANCE CHARACTERISTICS
GENERAL
Working Voltage:
C0G – 50, 100 & 200 Volts
X7R – 50, 100 & 200 Volts
Temperature Characteristics:
C0G – 0 30 PPM/ºC from -55ºC to +125ºC
X7R – 15% from -55ºC to +125ºC
Capacitance To lerance:
C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%
(±0.5 pF is tightest available tolerance)
X7R – ±10%, ±20%, -0 +100%, -20% +80%
Construction:
Monolithic block of ceramic dielectric with interdigitated
internal electrodes, encapsulated in a molded case, and
having axial or radial leads. Meets flame test requirements
of UL Standard 94V-0.
Te rminal Strength:
EIA-198 Method 303 Condition A (2.2 kg)
ELECTRICAL
Capacitance:
Within specified tolerance when measured with 1 volt rms
at 1 kHz (1000 pF or less at 1 MHz for C0G).
Dissipation Factor:
25ºC at 1 kHz (1000 pF or less at 1 MHz for C0G).
C0G – .15% maximum
X7R – 2.5% maximum
Insulation Resistance:
After 2 minutes electrification at 25ºC and rated voltage
C0G – 100K megohms or 1000 megohm - µF, whichever
is less.
X7R – 100K megohms or 1000 megohm - µF, whichever
is less.
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current limited
to 50 mA at 25ºC.
Life Test:
2000 hours at 200% of rated voltage at 125ºC. Post-Test
limits at 25ºC are:
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current
limited to 50 mA.
ENVIRONMENTAL
Moisture Resistance:
MIL-STD-202, Method 106, or EIA-198, Method 204,
Condition A, except 20 cycles.
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current
limited to 50 mA.
Immersion Cycling:
MIL-STD-202, Method 104, Condition B. Post-Test limits
at 25°C are:
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Solderability:
MIL-STD-202, Method 208, Sn62 solder, 245ºC for 5 1/2
seconds.
Resistance to Soldering Heat:
MIL-STD-202, Method 210, Condition B (260ºC, 10 secs).
Depth of immersion — to a minimum of .050" from the
capacitor body.
Lead Material:
Axial: Solder-coated copper clad steel
Radial: Solder-coated copper
Capacitance Change:
C0G – less than 3% or 0.25 pF, whichever is higher
X7R – ±20% of initial value
Dissipation Factor:
C0G – .25% maximum
X7R – 3.0% maximum
6
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/AXIAL & RADIAL - MIL-PRF-20
CAPACITOR OUTLINE DRAWINGS (AXIAL LEADS)
1.50 Min.
(38.10)
L
1.50 Min.
(38.10)
D
C
DIMENSIONS — INCHES & (MILLIMETERS)
CASE
SIZE
MILITARY
EQUIVALENT STYLES
L
C114
CC75, CCR75
.160 ± .010 (4.06 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
C124
CC76, CCR76
.250 ± .010 (6.35 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
C192
CC77, CCR77
.390 ± .010 (9.91 ± .25)
.140 ± .010 (3.56 ± .25)
.025, +.002, -.002 (.64, +.05, -.05)
C202
CC78, CCR78
.500 ± .020 (12.70 ± .51)
.250 ± .015 (6.35 ± .38)
.025, +.002, -.002 (.64, +.05, -.05)
C222
CC79, CCR79
.690 ± .030 (17.53 ± .76)
.350 ± .020 (8.89 ± .51)
.025, +.002, -.002 (.64, +.05, -.05)
D
C
CAPACITOR OUTLINE DRAWINGS (RADIAL LEADS)
C052 (CC05, CCR05)
L
L
W
L
W
H
1.25
MIN.
C062 (CC06, CCR06), C512 (CC07, CCR07),
C522 (CC08, CCR08)
C056 (CCR05)
C066 (CCR06)
W
L
H
Lead Dia.
.025
(+.004
-.002)
.045
MAX.
.026
MIN.
1.25
MIN.
Lead Dia.
.025
(+.004
-.002)
S
S
1.25
MIN.
W
.026
MIN.
H
Lead Dia.
.025
(+.004
-.002)
1.25
MIN.
S
Center Line of leads within .030" of Center Line of case.
Lead Dia.
.025
(+.004
-.002)
S
* Leads are .625 minimum when tape and reel packaged
DIMENSIONS — INCHES & (MILLIMETERS)
CASE
SIZE
C052/
C056
C062/
C066
C512
C522
MILITARY
EQUIVALENT
STYLES
H
HEIGHT
L
LENGTH
W
WIDTH
S
LEAD
SPACING
CC05, CCR05
.190 ± .010 (4.83 ± .25)
.190 ± .010 (4.83 ± .25)
.090 ± .010 (2.29 ± .25)
.200 ± .015 (5.08 ± .38)
CC06, CCR06
.290 ± .010 (7.37 ± .25)
.290 ± .010 (7.37 ± .25)
.090 ± .010 (2.29 ±
. 25)
.200 ± .015 (5.08 ± .38)
CC07, CCR07
CC08, CCR08
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
.140 ±
. 010 (3.56 ± .25)*
.240 ± .010 (6.10 ± .25)
.400 ± .020 (10.16 ± .51)
.400 ± .020 (10.16 ± .51)
* 0.200 (5.08) maximum for 100,000 pF only.
7
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/AXIAL & RADIAL - MIL-PRF-20
ORDERING INFORMATION
C 052 G 102 J 1 G 5 C R**
CERAMIC
FAILURE RATE
A
M
P
R
S
*CASE SIZE
(See Table Below)
SPECIFICATION
Military
G — MIL-PRF-20
LEAD MATERIAL
CAPACITANCE
C — Standard
In picofarad code: First two digits are significant
figures and third is number of zeroes following
(except 9 indicates division by 10). Examples:
0.1 ␮F = 100,000 pF = 104 and 9.1 pF = 919.
See tables for Standard Values.
INTERNAL CONSTRUCTION
5 — Standard
CAPACITANCE TOLERANCE
Standard
K — ±10%
J — ±5%
Others
G — ±2%
C — ±0.25 pF
F — ±1%
D — ±0.5 pF
B — ±0.1 pF
WORKING
VOLTAGE
1 — 100
2 — 200
5 — 50
TEMPERATURE CHARACTERISTIC
KEMET
Military
EIA
Designator Equivalent Equivalent
Standard tolerances for each Series are
shown in the repetitive parts lists.
*CASE SIZES
RADIAL
AXIAL
C052
C114
C056
C124
C062
C192
C066
C202
C512
C222
C522
— Not Applicable (Std.)
— 1.0%
— 0.1%
— 0.01%
— 0.001%
G
(Ultra
Stable)
*CH —
*CJ —
*CK —
*CX —
*CG
(See below)
Capacitance Change With Temp.
Measured Measured
Without
With Bias
Temp.
DC Bias
(Rated
Range, °C
Voltage
Voltage)
C0G
(NPO)
-55 to
+125
±30
ppm/°C*
±30
ppm/°C*
±60 ppm/°C 8.2 pF-18.0 pF.
±120 ppm/°C 4.3 pF-7.5 pF.
±250 ppm/°C 2.2 pF-3.9 pF
not measurable 0.1 pF-2.0 pF.
**Part Number Example: C052G102J1G5CR (14 digits – no spaces)
CAPACITOR MARKING
CC(R) 75, 76
JCK
2R2
CM5
“J” Brand (CCR only), Temperature Characteristic
Capacitance
Capacitance Tolerance, Failure Rate (CCR only),
Year Code
Lot Code, Trademark (K)
11AK
CC(R) 77
CCR77C
G102JM
J31433
0504A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“J” Brand (CCR only), FSCM (Federal Source Code)
Date/Lot Code
CC(R) 78
CCR78CG
103FR
JAN K
31433
100V
0504A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“JAN” Brand (CCR only), Trademark (K)
FSCM (Federal Source Code)
Voltage
Date/Lot Code
CC(R) 79
CCR79CG
103KM
JAN K
31433
200V
0504A
8
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“JAN” Brand (CCR only), Trademark
FSCM (Federal Source Code)
Voltage
Date/Lot Code
FRONT
CCR0
5CH1
00FR
REAR
CC(R) 05
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
** For the standoff style, a “V” is added after the
failure rate, or last character.
0504
AJ3
1433
Date Code
Lot Code, “J” Brand (CCR only),
FSCM (Federal Source Code)
FRONT
CCR06
CG102
JS
CC(R) 06
REAR
0504A
J100V
31433
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
** For the standoff style, a “V” is added after the
failure rate, or last character.
Date/LotCode
“J” Brand (CCR only), Voltage
FSCM (Federal Source Code)
CC(R) 07
CCR07CG
472KM
JAN KEMET
31433
200V 0504A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“JAN” Brand, Trademark
FSCM (Federal Source Code)
Voltage, Date/Lot Code
CCR08CG
472KM
JAN KEMET
31433
200V 0509A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“JAN” Brand, Trademark
FSCM (Federal Source Code)
Voltage, Date/Lot Code
CC(R) 08
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/AXIAL - MIL-PRF-20
ULTRA-STABLE TEMPERATURE CHARACTERISTIC - CG (EIA-C0G)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10.0
11.0
12.0
13.0
15.0
16.0
18.0
20.0
22.0
24.0
27.0
30.0
33.0
36.0
39.0
43.0
47.0
51.0
56.0
62.0
68.0
75.0
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
200 VOLT — C114 (CC(R)75 PER MIL-PRF-20/27)
C114G109(2)2G5C(1) CC75CX1R0(2) CCR75CX1R0(2)(1)
C114G119(2)2G5C(1) CC75CX1R1(2) CCR75CX1R1(2)(1)
C114G129(2)2G5C(1) CC75CX1R2(2) CCR75CX1R2(2)(1)
C114G139(2)2G5C(1) CC75CX1R3(2) CCR75CX1R3(2)(1)
C114G159(2)2G5C(1) CC75CX1R5(2) CCR75CX1R5(2)(1)
C114G169(2)2G5C(1) CC75CX1R6(2) CCR75CX1R6(2)(1)
C114G189(2)2G5C(1) CC75CX1R8(2) CCR75CX1R8(2)(1)
C114G209(2)2G5C(1) CC75CX2R0(2) CCR75CX2R0(2)(1)
C114G229(2)2G5C(1) CC75CK2R2(2) CCR75CK2R2(2)(1)
C114G249(2)2G5C(1) CC75CK2R4(2) CCR75CK2R4(2)(1)
C114G279(3)2G5C(1) CC75CK2R7(3) CCR75CK2R7(3)(1)
C114G309(3)2G5C(1) CC75CK3R0(3) CCR75CK3R0(3)(1)
C114G339(3)2G5C(1) CC75CK3R3(3) CCR75CK3R3(3)(1)
C114G369(3)2G5C(1) CC75CK3R6(3) CCR75CK3R6(3)(1)
C114G399(3)2G5C(1) CC75CK3R9(3) CCR75CK3R9(3)(1)
C114G439(3)2G5C(1) CC75CJ4R3(3) CCR75CJ4R3(3)(1)
C114G479(3)2G5C(1) CC75CJ4R7(3) CCR75CJ4R7(3)(1)
C114G519(3)2G5C(1) CC75CJ5R1(3) CCR75CJ5R1(3)(1)
C114G569(3)2G5C(1) CC75CJ5R6(3) CCR75CJ5R6(3)(1)
C114G629(3)2G5C(1) CC75CJ6R2(3) CCR75CJ6R2(3)(1)
C114G689(3)2G5C(1) CC75CJ6R8(3) CCR75CJ6R8(3)(1)
C114G759(3)2G5C(1) CC75CJ7R5(3) CCR75CJ7R5(3)(1)
C114G829(3)2G5C(1) CC75CH8R2(3) CCR75CH8R2(3)(1)
C114G919(3)2G5C(1) CC75CH9R1(3) CCR75CH9R1(3)(1)
C114G100(4)2G5C(1) CC75CH100(4) CCR75CH100(4)(1)
C114G110(4)2G5C(1) CC75CH110(4) CCR75CH110(4)(1)
C114G120(4)2G5C(1) CC75CH120(4) CCR75CH120(4)(1)
C114G130(4)2G5C(1) CC75CH130(4) CCR75CH130(4)(1)
C114G150(4)2G5C(1) CC75CH150(4) CCR75CH150(4)(1)
C114G160(4)2G5C(1) CC75CH160(4) CCR75CH160(4)(1)
C114G180(4)2G5C(1) CC75CH180(4) CCR75CH180(4)(1)
C114G200(4)2G5C(1) CC75CG200(4) CCR75CG200(4)(1)
C114G220(4)2G5C(1) CC75CG220(4) CCR75CG220(4)(1)
C114G240(4)2G5C(1) CC75CG240(4) CCR75CG240(4)(1)
C114G270(4)2G5C(1) CC75CG270(4) CCR75CG270(4)(1)
C114G300(4)2G5C(1) CC75CG300(4) CCR75CG300(4)(1)
C114G330(4)2G5C(1) CC75CG330(4) CCR75CG330(4)(1)
C114G360(4)2G5C(1) CC75CG360(4) CCR75CG360(4)(1)
C114G390(4)2G5C(1) CC75CG390(4) CCR75CG390(4)(1)
C114G430(4)2G5C(1) CC75CG430(4) CCR75CG430(4)(1)
C114G470(4)2G5C(1) CC75CG470(4) CCR75CG470(4)(1)
C114G510(4)2G5C(1) CC75CG510(4) CCR75CG510(4)(1)
C114G560(4)2G5C(1) CC75CG560(4) CCR75CG560(4)(1)
C114G620(4)2G5C(1) CC75CG620(4) CCR75CG620(4)(1)
C114G680(4)2G5C(1) CC75CG680(4) CCR75CG680(4)(1)
C114G750(4)2G5C(1) CC75CG750(4) CCR75CG750(4)(1)
To complete Part Number, insert the following letters:
(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).
(2) Available Capacitance Tolerances: B, C.
(3) Available Capacitance Tolerances: B, C, D.
(4) Available Capacitance Tolerances: F, G, J.
CAP.
pF
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
100 VOLT — C114 (CC(R)75 PER MIL-PRF-20/27)
82.0
91.0
100.0
110.0
120.0
130.0
150.0
160.0
180.0
200.0
220.0
240.0
C114G820(4)1G5C(1)
C114G910(4)1G5C(1)
C114G101(4)1G5C(1)
C114G111(4)1G5C(1)
C114G121(4)1G5C(1)
C114G131(4)1G5C(1)
C114G151(4)1G5C(1)
C114G161(4)1G5C(1)
C114G181(4)1G5C(1)
C114G201(4)1G5C(1)
C114G221(4)1G5C(1)
C114G241(4)1G5C(1)
CC75CG820(4)
CC75CG910(4)
CC75CG101(4)
CC75CG111(4)
CC75CG121(4)
CC75CG131(4)
CC75CG151(4)
CC75CG161(4)
CC75CG181(4)
CC75CG201(4)
CC75CG221(4)
CC75CG241(4)
CCR75CG820(4)(1)
CCR75CG910(4)(1)
CCR75CG101(4)(1)
CCR75CG111(4)(1)
CCR75CG121(4)(1)
CCR75CG131(4)(1)
CCR75CG151(4)(1)
CCR75CG161(4)(1)
CCR75CG181(4)(1)
CCR75CG201(4)(1)
CCR75CG221(4)(1)
CCR75CG241(4)(1)
50 VOLT — C114 (CC(R)75 PER MIL-PRF-20/27)
C114G271(4)5G5C(1) CC75CG271(4) CCR75CG271(4)(1)
C114G301(4)5G5C(1) CC75CG301(4) CCR75CG301(4)(1)
C114G331(4)5G5C(1) CC75CG331(4) CCR75CG331(4)(1)
C114G361(4)5G5C(1) CC75CG361(4) CCR75CG361(4)(1)
C114G391(4)5G5C(1) CC75CG391(4) CCR75CG391(4)(1)
C114G431(4)5G5C(1) CC75CG431(4) CCR75CG431(4)(1)
C114G471(4)5G5C(1) CC75CG471(4) CCR75CG471(4)(1)
C114G511(4)5G5C(1) CC75CG511(4) CCR75CG511(4)(1)
C114G561(4)5G5C(1) CC75CG561(4) CCR75CG561(4)(1)
C114G621(4)5G5C(1) CC75CG621(4) CCR75CG621(4)(1)
C114G681(4)5G5C(1) CC75CG681(4) CCR75CG681(4)(1)
200 VOLT — C124 (CC(R)76 PER MIL-PRF-20/28)
82.0 C124G820(4)2G5C(1) CC76CG820(4) CCR76CG820(4)(1)
91.0 C124G910(4)2G5C(1) CC76CG910(4) CCR76CG910(4)(1)
100.0 C124G101(4)2G5C(1) CC76CG101(4) CCR76CG101(4)(1)
110.0 C124G111(4)2G5C(1) CC76CG111(4) CCR76CG111(4)(1)
120.0 C124G121(4)2G5C(1) CC76CG121(4) CCR76CG121(4)(1)
130.0 C124G131(4)2G5C(1) CC76CG131(4) CCR76CG131(4)(1)
100 VOLT — C124 (CC(R)76 PER MIL-PRF-20/28)
270.0 C124G271(4)1G5C(1) CC76CG271(4) CCR76CG271(4)(1)
300.0 C124G301(4)1G5C(1) CC76CG301(4) CCR76CG301(4)(1)
330.0 C124G331(4)1G5C(1) CC76CG331(4) CCR76CG331(4)(1)
360.0 C124G361(4)1G5C(1) CC76CG361(4) CCR76CG361(4)(1)
390.0 C124G391(4)1G5C(1) CC76CG391(4) CCR76CG391(4)(1)
430.0 C124G431(4)1G5C(1) CC76CG431(4) CCR76CG431(4)(1)
470.0 C124G471(4)1G5C(1) CC76CG471(4) CCR76CG471(4)(1)
510.0 C124G511(4)1G5C(1) CC76CG511(4) CCR76CG511(4)(1)
560.0 C124G561(4)1G5C(1) CC76CG561(4) CCR76CG561(4)(1)
620.0 C124G621(4)1G5C(1) CC76CG621(4) CCR76CG621(4)(1)
680.0 C124G681(4)1G5C(1) CC76CG681(4) CCR76CG681(4)(1)
50 VOLT — C124 (CC(R)76 PER MIL-PRF-20/28)
750.0 C124G751(4)5G5C(1) CC76CG751(4) CCR76CG751(4)(1)
820.0 C124G821(4)5G5C(1) CC76CG821(4) CCR76CG821(4)(1)
910.0 C124G911(4)5G5C(1) CC76CG911(4) CCR76CG911(4)(1)
1,000.0 C124G102(4)5G5C(1) CC76CG102(4) CCR76CG102(4)(1)
200 VOLT — C192 (CC(R)77 PER MIL-PRF-20/29)
150.0 C192G151(4)2G5C(1) CC77CG151(4) CCR77CG151(4)(1)
160.0 C192G161(4)2G5C(1) CC77CG161(4) CCR77CG161(4)(1)
180.0 C192G181(4)2G5C(1) CC77CG181(4) CCR77CG181(4)(1)
200.0 C192G201(4)2G5C(1) CC77CG201(4) CCR77CG201(4)(1)
220.0 C192G221(4)2G5C(1) CC77CG221(4) CCR77CG221(4)(1)
240.0 C192G241(4)2G5C(1) CC77CG241(4) CCR77CG241(4)(1)
270.0 C192G271(4)2G5C(1) CC77CG271(4) CCR77CG271(4)(1)
300.0 C192G301(4)2G5C(1) CC77CG301(4) CCR77CG301(4)(1)
330.0 C192G331(4)2G5C(1) CC77CG331(4) CCR77CG331(4)(1)
360.0 C192G361(4)2G5C(1) CC77CG361(4) CCR77CG361(4)(1)
390.0 C192G391(4)2G5C(1) CC77CG391(4) CCR77CG391(4)(1)
430.0 C192G431(4)2G5C(1) CC77CG431(4) CCR77CG431(4)(1)
470.0 C192G471(4)2G5C(1) CC77CG471(4) CCR77CG471(4)(1)
510.0 C192G511(4)2G5C(1) CC77CG511(4) CCR77CG511(4)(1)
560.0 C192G561(4)2G5C(1) CC77CG561(4) CCR77CG561(4)(1)
620.0 C192G621(4)2G5C(1) CC77CG621(4) CCR77CG621(4)(1)
680.0 C192G681(4)2G5C(1) CC77CG681(4) CCR77CG681(4)(1)
270.0
300.0
330.0
360.0
390.0
430.0
470.0
510.0
560.0
620.0
680.0
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
9
CERAMIC MOLDED/AXIAL - MIL-PRF-20
ULTRA-STABLE TEMPERATURE CHARACTERISTIC - CG (EIA-C0G)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
2,400.0
2,700.0
3,000.0
3,300.0
3,600.0
3,900.0
4,300.0
4,700.0
5,100.0
5,600.0
100 VOLT — C192 (CC(R)77 PER MIL-PRF-20/29)
C192G751(4)1G5C(1) CC77CG751(4) CCR77CG751(4)(1)
C192G821(4)1G5C(1) CC77CG821(4) CCR77CG821(4)(1)
C192G911(4)1G5C(1) CC77CG911(4) CCR77CG911(4)(1)
C192G102(4)1G5C(1) CC77CG102(4) CCR77CG102(4)(1)
C192G112(4)1G5C(1) CC77CG112(4) CCR77CG112(4)(1)
C192G122(4)1G5C(1) CC77CG122(4) CCR77CG122(4)(1)
C192G132(4)1G5C(1) CC77CG132(4) CCR77CG132(4)(1)
C192G152(4)1G5C(1) CC77CG152(4) CCR77CG152(4)(1)
C192G162(4)1G5C(1) CC77CG162(4) CCR77CG162(4)(1)
C192G182(4)1G5C(1) CC77CG182(4) CCR77CG182(4)(1)
C192G202(4)1G5C(1) CC77CG202(4) CCR77CG202(4)(1)
C192G222(4)1G5C(1) CC77CG222(4) CCR77CG222(4)(1)
50 VOLT — C192 (CC(R)77 PER MIL-PRF-20/29)
C192G242(4)5G5C(1) CC77CG242(4) CCR77CG242(4)(1)
C192G272(4)5G5C(1) CC77CG272(4) CCR77CG272(4)(1)
C192G302(4)5G5C(1) CC77CG302(4) CCR77CG302(4)(1)
C192G332(4)5G5C(1) CC77CG332(4) CCR77CG332(4)(1)
C192G362(4)5G5C(1) CC77CG362(4) CCR77CG362(4)(1)
C192G392(4)5G5C(1) CC77CG392(4) CCR77CG392(4)(1)
C192G432(4)5G5C(1) CC77CG432(4) CCR77CG432(4)(1)
C192G472(4)5G5C(1) CC77CG472(4) CCR77CG472(4)(1)
C192G512(5)5G5C(1) CC77CG512(5) CCR77CG512(5)(1)
C192G562(5)5G5C(1) CC77CG562(5) CCR77CG562(5)(1)
820.0
1,000.0
1,200.0
1,500.0
1,800.0
2,200.0
2,700.0
3,300.0
200 VOLT — C202 (CC(R)78 PER MIL-PRF-20/30)
C202G821(5)2G5C(1) CC78CG821(5) CCR78CG821(5)(1)
C202G102(5)2G5C(1) CC78CG102(5) CCR78CG102(5)(1)
C202G122(5)2G5C(1) CC78CG122(5) CCR78CG122(5)(1)
C202G152(5)2G5C(1) CC78CG152(5) CCR78CG152(5)(1)
C202G182(5)2G5C(1) CC78CG182(5) CCR78CG182(5)(1)
C202G222(5)2G5C(1) CC78CG222(5) CCR78CG222(5)(1)
C202G272(5)2G5C(1) CC78CG272(5) CCR78CG272(5)(1)
C202G332(5)2G5C(1) CC78CG332(5) CCR78CG332(5)(1)
750.0
820.0
910.0
1,000.0
1,100.0
1,200.0
1,300.0
1,500.0
1,600.0
1,800.0
2,000.0
2,200.0
CAP.
pF
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
100 VOLT — C202 (CC(R)78 PER MIL-PRF-20/30)
3,900.0 C202G392(5)1G5C(1) CC78CG392(5) CCR78CG392(5)(1)
4,700.0 C202G472(5)1G5C(1) CC78CG472(5) CCR78CG472(5)(1)
5,600.0 C202G562(5)1G5C(1) CC78CG562(5) CCR78CG562(5)(1)
6,800.0 C202G682(5)1G5C(1) CC78CG682(5) CCR78CG682(5)(1)
8,200.0 C202G822(5)1G5C(1) CC78CG822(5) CCR78CG822(5)(1)
10,000.0 C202G103(5)1G5C(1) CC78CG103(5) CCR78CG103(5)(1)
12,000.0 C202G123(5)1G5C(1) CC78CG123(5) CCR78CG123(5)(1)
50 VOLT — C202 (CC(R)78 PER MIL-PRF-20/30)
15,000.0 C202G153(5)5G5C(1) CC78CG153(5) CCR78CG153(5)(1)
18,000.0 C202G183(5)5G5C(1) CC78CG183(5) CCR78CG183(5)(1)
22,000.0 C202G223(5)5G5C(1) CC78CG223(5) CCR78CG223(5)(1)
27,000.0 C202G273(5)5G5C(1) CC78CG273(5) CCR78CG273(5)(1)
200 VOLT — C222 (CC(R)79 PER MIL-PRF-20/31)
3,900.0 C222G392(5)2G5C(1) CC79CG392(5) CCR79CG392(5)(1)
4,700.0 C222G472(5)2G5C(1) CC79CG472(5) CCR79CG472(5)(1)
5,600.0 C222G562(5)2G5C(1) CC79CG562(5) CCR79CG562(5)(1)
6,800.0 C222G682(5)2G5C(1) CC79CG682(5) CCR79CG682(5)(1)
8,200.0 C222G822(5)2G5C(1) CC79CG822(5) CCR79CG822(5)(1)
10,000.0 C222G103(5)2G5C(1) CC79CG103(5) CCR79CG103(5)(1)
100 VOLT — C222 (CC(R)79 PER MIL-PRF-20/31)
15,000.0 C222G153(5)1G5C(1) CC79CG153(5) CCR79CG153(5)(1)
18,000.0 C222G183(5)1G5C(1) CC79CG183(5) CCR79CG183(5)(1)
22,000.0 C222G223(5)1G5C(1) CC79CG223(5) CCR79CG223(5)(1)
27,000.0 C222G273(5)1G5C(1) CC79CG273(5) CCR79CG273(5)(1)
33,000.0 C222G333(5)1G5C(1) CC79CG333(5) CCR79CG333(5)(1)
39,000.0 C222G393(5)1G5C(1) CC79CG393(5) CCR79CG393(5)(1)
50 VOLT — C222 (CC(R)79 PER MIL-PRF-20/31)
47,000.0 C222G473(5)5G5C(1) CC79CG473(5) CCR79CG473(5)(1)
56,000.0 C222G563(5)5G5C(1) CC79CG563(5) CCR79CG563(5)(1)
68,000.0 C222G683(5)5G5C(1) CC79CG683(5) CCR79CG683(5)(1)
82,000.0 C222G823(5)5G5C(1) CC79CG823(5) CCR79CG823(5)(1)
To complete Part Number, insert the following letters:
(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).
(2) Available Capacitance Tolerances: B, C.
(3) Available Capacitance Tolerances: B, C, D.
(4) Available Capacitance Tolerances: F, G, J.
(5) Available Capacitance Tolerances: F, G, J, K.
10
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/AXIAL - MIL-PRF-20
ULTRA-STABLE TEMPERATURE CHARACTERISTIC - CG (EIA-C0G)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
200 VOLT — C052/C056 SIZE (CC(R)05 PER MIL-PRF-20/35)
1.0
C05(6)G109(2)2G5C(1) CC05CX1R0(2) CCR05CX1R0(2)(1)(7)
1.1
C05(6)G119(2)2G5C(1) CC05CX1R1(2) CCR05CX1R1(2)(1)(7)
1.2
C05(6)G129(2)2G5C(1) CC05CX1R2(2) CCR05CX1R2(2)(1)(7)
1.3
C05(6)G139(2)2G5C(1) CC05CX1R3(2) CCR05CX1R3(2)(1)(7)
1.5
C05(6)G159(2)2G5C(1) CC05CX1R5(2) CCR05CX1R5(2)(1)(7)
1.6
C05(6)G169(2)2G5C(1) CC05CX1R6(2) CCR05CX1R6(2)(1)(7)
1.8
C05(6)G189(2)2G5C(1) CC05CX1R8(2) CCR05CX1R8(2)(1)(7)
2.0
C05(6)G209(2)2G5C(1) CC05CX2R0(2) CCR05CX2R0(2)(1)(7)
2.2
C05(6)G229(2)2G5C(1) CC05CK2R2(2) CCR05CK2R2(2)(1)(7)
2.4
C05(6)G249(2)2G5C(1) CC05CK2R4(2) CCR05CK2R4(2)(1)(7)
2.7
C05(6)G279(3)2G5C(1) CC05CK2R7(3) CCR05CK2R7(3)(1)(7)
3.0
C05(6)G309(3)2G5C(1) CC05CK3R0(3) CCR05CK3R0(3)(1)(7)
3.3
C05(6)G339(3)2G5C(1) CC05CK3R3(3) CCR05CK3R3(3)(1)(7)
3.6
C05(6)G369(3)2G5C(1) CC05CK3R6(3) CCR05CK3R6(3)(1)(7)
3.9
C05(6)G399(3)2G5C(1) CC05CK3R9(3) CCR05CK3R9(3)(1)(7)
4.3
C05(6)G439(3)2G5C(1) CC05CJ4R3(3) CCR05CJ4R3(3)(1)(7)
4.7
C05(6)G479(3)2G5C(1) CC05CJ4R7(3) CCR05CJ4R7(3)(1)(7)
5.1
C05(6)G519(3)2G5C(1) CC05CJ5R1(3) CCR05CJ5R1(3)(1)(7)
5.6
C05(6)G569(3)2G5C(1) CC05CJ5R6(3) CCR05CJ5R6(3)(1)(7)
6.2
C05(6)G629(3)2G5C(1) CC05CJ6R2(3) CCR05CJ6R2(3)(1)(7)
6.8
C05(6)G689(3)2G5C(1) CC05CJ6R8(3) CCR05CJ6R8(3)(1)(7)
7.5
C05(6)G759(3)2G5C(1) CC05CJ7R5(3) CCR05CJ7R5(3)(1)(7)
8.2
C05(6)G829(3)2G5C(1) CC05CH8R2(3) CCR05CH8R2(3)(1)(7)
9.1
C05(6)G919(3)2G5C(1) CC05CH9R1(3) CCR05CH9R1(3)(1)(7)
10.0
C05(6)G100(4)2G5C(1) CC05CH100(4) CCR05CH100(4)(1)(7)
11.0
C05(6)G110(4)2G5C(1) CC05CH110(4) CCR05CH110(4)(1)(7)
12.0
C05(6)G120(4)2G5C(1) CC05CH120(4) CCR05CH120(4)(1)(7)
13.0
C05(6)G130(4)2G5C(1) CC05CH130(4) CCR05CH130(4)(1)(7)
15.0
C05(6)G150(4)2G5C(1) CC05CH150(4) CCR05CH150(4)(1)(7)
16.0
C05(6)G160(4)2G5C(1) CC05CH160(4) CCR05CH160(4)(1)(7)
18.0
C05(6)G180(4)2G5C(1) CC05CH180(4) CCR05CH180(4)(1)(7)
20.0
C05(6)G200(4)2G5C(1) CC05CG200(4) CCR05CG200(4)(1)(7)
22.0
C05(6)G220(4)2G5C(1) CC05CG220(4) CCR05CG220(4)(1)(7)
24.0
C05(6)G240(4)2G5C(1) CC05CG240(4) CCR05CG240(4)(1)(7)
27.0
C05(6)G270(4)2G5C(1) CC05CG270(4) CCR05CG270(4)(1)(7)
30.0
C05(6)G300(4)2G5C(1) CC05CG300(4) CCR05CG300(4)(1)(7)
33.0
C05(6)G330(4)2G5C(1) CC05CG330(4) CCR05CG330(4)(1)(7)
36.0
C05(6)G360(4)2G5C(1) CC05CG360(4) CCR05CG360(4)(1)(7)
39.0
C05(6)G390(4)2G5C(1) CC05CG390(4) CCR05CG390(4)(1)(7)
43.0
C05(6)G430(4)2G5C(1) CC05CG430(4) CCR05CG430(4)(1)(7)
47.0
C05(6)G470(4)2G5C(1) CC05CG470(4) CCR05CG470(4)(1)(7)
51.0
C05(6)G510(4)2G5C(1) CC05CG510(4) CCR05CG510(4)(1)(7)
To complete Part Number, insert the following letters:
(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).
(2) Available Capacitance Tolerances: B, C.
(3) Available Capacitance Tolerances: B, C, D.
(4) Available Capacitance Tolerances: F, G, J.
(5) Available Capacitance Tolerances: F, G, J, K.
(6) Insert “2” for standard design, Style C052G
Stand-offs are available
Insert “6” for stand-off design, Style C056G
only as CCR’s, not available as CC.
(7) Add “V” for stand-off design, Style C056G
And leave blank for the flat bottom design (C052G)
CAP.
pF
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
200 VOLT — C052/C056 SIZE (CC(R)05 PER MIL-PRF-20/35)
56.0 C05(6)G560(4)2G5C(1) CC05CG560(4) CCR05CG560(4)(1)(7)
62.0 C05(6)G620(4)2G5C(1) CC05CG620(4) CCR05CG620(4)(1)(7)
68.0 C05(6)G680(4)2G5C(1) CC05CG680(4) CCR05CG680(4)(1)(7)
75.0 C05(6)G750(4)2G5C(1) CC05CG750(4) CCR05CG750(4)(1)(7)
82.0 C05(6)G820(4)2G5C(1) CC05CG820(4) CCR75CG820(4)(1)(7)
91.0 C05(6)G910(4)2G5C(1) CC05CG910(4) CCR05CG910(4)(1)(7)
100.0 C05(6)G101(4)2G5C(1) CC05CG101(4) CCR05CG101(4)(1)(7)
110.0 C05(6)G111(4)2G5C(1) CC05CG111(4) CCR05CG111(4)(1)(7)
120.0 C05(6)G121(4)2G5C(1) CC05CG121(4) CCR05CG121(4)(1)(7)
130.0 C05(6)G131(4)2G5C(1) CC05CG131(4) CCR05CG131(4)(1)(7)
150.0 C05(6)G151(4)2G5C(1) CC05CG151(4) CCR05CG151(4)(1)(7)
160.0 C05(6)G161(4)2G5C(1) CC05CG161(4) CCR05CG161(4)(1)(7)
180.0 C05(6)G181(4)2G5C(1) CC05CG181(4) CCR05CG181(4)(1)(7)
200.0 C05(6)G201(4)2G5C(1) CC05CG201(4) CCR05CG201(4)(1)(7)
220.0 C05(6)G221(4)2G5C(1) CC05CG221(4) CCR05CG221(4)(1)(7)
240.0 C05(6)G241(4)2G5C(1) CC05CG241(4) CCR05CG241(4)(1)(7)
270.0 C05(6)G271(4)2G5C(1) CC05CG271(4) CCR05CG271(4)(1)(7)
300.0 C05(6)G301(4)2G5C(1) CC05CG301(4) CCR05CG301(4)(1)(7)
330.0 C05(6)G331(4)2G5C(1) CC05CG331(4) CCR05CG331(4)(1)(7)
100 VOLT — C052/C056 SIZE (CC(R)05 PER MIL-PRF-20/35)
360.0 C05(6)G361(4)1G5C(1) CC05CG361(4) CCR05CG361(4)(1)(7)
390.0 C05(6)G391(4)1G5C(1) CC05CG391(4) CCR05CG391(4)(1)(7)
430.0 C05(6)G431(4)1G5C(1) CC05CG431(4) CCR05CG431(4)(1)(7)
470.0 C05(6)G471(4)1G5C(1) CC05CG471(4) CCR05CG471(4)(1)(7)
510.0 C05(6)G511(4)1G5C(1) CC05CG511(4) CCR05CG511(4)(1)(7)
560.0 C05(6)G561(4)1G5C(1) CC05CG561(4) CCR05CG561(4)(1)(7)
620.0 C05(6)G621(4)1G5C(1) CC05CG621(4) CCR05CG621(4)(1)(7)
680.0 C05(6)G681(4)1G5C(1) CC05CG681(4) CCR05CG681(4)(1)(7)
750.0 C05(6)G751(4)1G5C(1) CC05CG751(4) CCR05CG751(4)(1)(7)
820.0 C05(6)G821(4)1G5C(1) CC05CG821(4) CCR05CG821(4)(1)(7)
910.0 C05(6)G911(4)1G5C(1) CC05CG911(4) CCR05CG911(4)(1)(7)
1,000.0 C05(6)G102(4)1G5C(1) CC05CG102(4) CCR05CG102(4)(1)(7)
1,100.0 C05(6)G112(4)1G5C(1) CC05CG112(4) CCR05CG112(4)(1)(7)
1,200.0 C05(6)G122(4)1G5C(1) CC05CG122(4) CCR05CG122(4)(1)(7)
1,300.0 C05(6)G132(4)1G5C(1) CC05CG132(4) CCR05CG132(4)(1)(7)
1,500.0 C05(6)G152(4)1G5C(1) CC05CG152(4) CCR05CG152(4)(1)(7)
1,600.0 C05(6)G162(4)1G5C(1) CC05CG162(4) CCR05CG162(4)(1)(7)
1,800.0 C05(6)G182(4)1G5C(1) CC05CG182(4) CCR05CG182(4)(1)(7)
50 VOLT — C052/C056 SIZE (CC(R)05 PER MIL-PRF-20/35)
2,000.0 C05(6)G202(4)5G5C(1) CC05CG202(4) CCR05CG202(4)(1)(7)
2,200.0 C05(6)G222(4)5G5C(1) CC05CG222(4) CCR05CG222(4)(1)(7)
2,400.0 C05(6)G242(4)5G5C(1) CC05CG242(4) CCR05CG242(4)(1)(7)
2,700.0 C05(6)G272(4)5G5C(1) CC05CG272(4) CCR05CG272(4)(1)(7)
3,000.0 C05(6)G302(4)5G5C(1) CC05CG302(4) CCR05CG302(4)(1)(7)
3,300.0 C05(6)G332(4)5G5C(1) CC05CG332(4) CCR05CG332(4)(1)(7)
}
11
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/AXIAL - MIL-PRF-20
ULTRA-STABLE TEMPERATURE CHARACTERISTIC - CG (EIA-C0G)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
200 VOLT — C062/C066 SIZE (CC(R)06 PER MIL-PRF-20/36)
360.0 C06(6)G361(4)2G5C(1) CC06CG361(4) CCR06CG361(4)(1)(7)
390.0 C06(6)G391(4)2G5C(1) CC06CG391(4) CCR06CG391(4)(1)(7)
430.0 C06(6)G431(4)2G5C(1) CC06CG431(4) CCR06CG431(4)(1)(7)
470.0 C06(6)G471(4)2G5C(1) CC06CG471(4) CCR06CG471(4)(1)(7)
510.0 C06(6)G511(4)2G5C(1) CC06CG511(4) CCR06CG511(4)(1)(7)
560.0 C06(6)G561(4)2G5C(1) CC06CG561(4) CCR06CG561(4)(1)(7)
620.0 C06(6)G621(4)2G5C(1) CC06CG621(4) CCR06CG621(4)(1)(7)
680.0 C06(6)G681(4)2G5C(1) CC06CG681(4) CCR06CG681(4)(1)(7)
750.0 C06(6)G751(4)2G5C(1) CC06CG751(4) CCR06CG751(4)(1)(7)
820.0 C06(6)G821(4)2G5C(1) CC06CG821(4) CCR06CG821(4)(1)(7)
910.0 C06(6)G911(4)2G5C(1) CC06CG911(4) CCR06CG911(4)(1)(7)
1,000.0 C06(6)G102(4)2G5C(1) CC06CG102(4) CCR06CG102(4)(1)(7)
1,100.0 C06(6)G112(4)2G5C(1) CC06CG112(4) CCR06CG112(4)(1)(7)
1,200.0 C06(6)G122(4)2G5C(1) CC06CG122(4) CCR06CG122(4)(1)(7)
1,300.0 C06(6)G132(4)2G5C(1) CC06CG132(4) CCR06CG132(4)(1)(7)
1,500.0 C06(6)G152(4)2G5C(1) CC06CG152(4) CCR06CG152(4)(1)(7)
1,600.0 C06(6)G162(4)2G5C(1) CC06CG162(4) CCR06CG162(4)(1)(7)
1,800.0 C06(6)G182(4)2G5C(1) CC06CG182(4) CCR06CG182(4)(1)(7)
100 VOLT — C062/C066 SIZE (CC(R)06 PER MIL-PRF-20/36)
2,000.0 C06(6)G202(4)1G5C(1) CC06CG202(4) CCR06CG202(4)(1)(7)
2,200.0 C06(6)G222(4)1G5C(1) CC06CG222(4) CCR06CG222(4)(1)(7)
2,400.0 C06(6)G242(4)1G5C(1) CC06CG242(4) CCR06CG242(4)(1)(7)
2,700.0 C06(6)G272(4)1G5C(1) CC06CG272(4) CCR06CG272(4)(1)(7)
3,000.0 C06(6)G302(4)1G5C(1) CC06CG302(4) CCR06CG302(4)(1)(7)
3,300.0 C06(6)G332(4)1G5C(1) CC06CG332(4) CCR06CG332(4)(1)(7)
3,600.0 C06(6)G362(4)1G5C(1) CC06CG362(4) CCR06CG362(4)(1)(7)
3,900.0 C06(6)G392(4)1G5C(1) CC06CG392(4) CCR06CG392(4)(1)(7)
4,300.0 C06(6)G432(4)1G5C(1) CC06CG432(4) CCR06CG432(4)(1)(7)
4,700.0 C06(6)G472(4)1G5C(1) CC06CG472(4) CCR06CG472(4)(1)(7)
50 VOLT — C062/C066 SIZE (CC(R)06 PER MIL-PRF-20/36)
5,100.0 C06(6)G512(5)5G5C(1) CC06CG512(5) CCR06CG512(5)(1)(7)
5,600.0 C06(6)G562(5)5G5C(1) CC06CG562(5) CCR06CG562(5)(1)(7)
6,200.0 C06(6)G622(5)5G5C(1) CC06CG622(5) CCR06CG622(5)(1)(7)
6,800.0 C06(6)G682(5)5G5C(1) CC06CG682(5) CCR06CG682(5)(1)(7)
7,500.0 C06(6)G752(5)5G5C(1) CC06CG752(5) CCR06CG752(5)(1)(7)
To complete Part Number, insert the following letters:
(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).
(2) Available Capacitance Tolerances: B, C.
(3) Available Capacitance Tolerances: B, C, D.
(4) Available Capacitance Tolerances: F, G, J.
(5) Available Capacitance Tolerances: F, G, J, K.
(6) Insert “2” for standard design, Style C062G
Stand-offs are available
Insert “6” for stand-off design, Style C066G
only as CCR’s, not available as CC.
(7) Add “V” for stand-off design, Style C066G
And leave blank for the flat bottom design (C062G)
(8) Available Capacitance Tolerances: G, J, K
CAP.
pF
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
50 VOLT — C062/C066 SIZE (CC(R)06 PER MIL-PRF-20/36)
8,200.0 C06(6)G822(5)5G5C(1) CC06CG822(5) CCR06CG822(5)(1)(7)
9,100.0 C06(6)G912(5)5G5C(1) CC06CG912(5) CCR06CG912(5)(1)(7)
10,000.0 C06(6)G103(5)5G5C(1) CC06CG103(5) CCR06CG103(5)(1)(7)
12,000.0 C06(6)G123(5)5G5C(1) CC06CG123(5) CCR06CG123(5)(1)(7)
15,000.0 C06(6)G153(5)5G5C(1) CC06CG153(5) CCR06CG153(5)(1)(7)
18,000.0 C06(6)G183(5)5G5C(1) CC06CG183(5) CCR06CG183(5)(1)(7)
200 VOLT — C512 SIZE (CC(R)07 PER MIL-PRF-20/37)
2,200.0 C512G222(5)2G5C(1) CC07CG222(5) CCR07CG222(5)(1)
2,700.0 C512G272(5)2G5C(1) CC07CG272(5) CCR07CG272(5)(1)
3,300.0 C512G332(5)2G5C(1) CC07CG332(5) CCR07CG332(5)(1)
3,900.0 C512G392(5)2G5C(1) CC07CG392(5) CCR07CG392(5)(1)
4,700.0 C512G472(5)2G5C(1) CC07CG472(5) CCR07CG472(5)(1)
100 VOLT — C512 SIZE (CC(R)07 PER MIL-PRF-20/37)
5,600.0 C512G562(5)1G5C(1) CC07CG562(5) CCR07CG562(5)(1)
6,800.0 C512G682(5)1G5C(1) CC07CG682(5) CCR07CG682(5)(1)
8,200.0 C512G822(5)1G5C(1) CC07CG822(5) CCR07CG822(5)(1)
10,000.0 C512G103(5)1G5C(1) CC07CG103(5) CCR07CG103(5)(1)
12,000.0 C512G123(5)1G5C(1) CC07CG123(5) CCR07CG123(5)(1)
50 VOLT — C512 SIZE (CC(R)07 PER MIL-PRF-20/37)
15,000.0 C512G153(5)5G5C(1) CC07CG153(5) CCR07CG153(5)(1)
18,000.0 C512G183(5)5G5C(1) CC07CG183(5) CCR07CG183(5)(1)
22,000.0 C512G223(5)5G5C(1) CC07CG223(5) CCR07CG223(5)(1)
27,000.0 C512G273(5)5G5C(1) CC07CG273(5) CCR07CG273(5)(1)
33,000.0 C512G333(5)5G5C(1) CC07CG333(5) CCR07CG333(5)(1)
39,000.0 C512G393(5)5G5C(1) CC07CG393(5) CCR07CG393(5)(1)
47,000.0 C512G473(5)5G5C(1) CC07CG473(5) CCR07CG473(5)(1)
56,000.0 C512G563(5)5G5C(1) CC07CG563(5) CCR07CG563(5)(1)
68,000.0 C512G683(5)5G5C(1) CC07CG683(5) CCR07CG683(5)(1)
83,000.0 C512G823(5)5G5C(1) CC07CG823(5) CCR07CG823(5)(1)
100,000.0 C512G104(5)5G5C(1) CC07CG104(5) CCR07CG104(5)(1)
200 VOLT — C522 SIZE (CC(R)08 PER MIL-PRF-20/38)
3,900.0 C522G392(8)2G5C(1) CC08CG392(8) CCR08CG392(8)(1)
4,700.0 C522G472(8)2G5C(1) CC08CG472(8) CCR08CG472(8)(1)
100 VOLT — C522 SIZE (CC(R)08 PER MIL-PRF-20/38)
15,000.0 C522G153(8)1G5C(1) CC08CG153(8) CCR08CG153(8)(1)
18,000.0 C522G183(8)1G5C(1) CC08CG183(8) CCR08CG183(8)(1)
50 VOLT — C522 SIZE (CC(R)08 PER MIL-PRF-20/38)
56,000.0 C522G563(8)5G5C(1) CC08CG563(8) CCR08CG563(8)(1)
68,000.0 C522G683(8)5G5C(1) CC08CG683(8) CCR08CG683(8)(1)
}
12
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/MIL-C-11015 (CK) & MIL-PRF-39014 (CKR)
CAPACITOR OUTLINE DRAWINGS (AXIAL LEADS)
1.50 Min.
(38.10)
L
1.50 Min.
(38.10)
D
C
DIMENSIONS — INCHES & (MILLIMETERS)
CASE
SIZE
MILITARY
EQUIVALENT STYLES
L
D
C
C114
CK12, CKR11
.160 ± .010 (4.06 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
C124
CK13, CKR12
.250 ± .010 (6.35 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
C192
CK14, CKR14
.390 ± .010 (9.91 ± .25)
.140 ± .010 (3.56 ± .25)
.025, +.002, -.002 (.64, +.05, -.05)
C202
CK15, CKR15
.500 ± .020 (12.70 ± .51)
.250 ± .015 (6.35 ± .38)
.025, +.002, -.002 (.64, +.05, -.05)
C222
CK16, CKR16
.690 ± .030 (17.53 ± .76)
.350 ± .020 (8.89 ± .51)
.025, +.002, -.002 (.64, +.05, -.05)
CAPACITOR OUTLINE DRAWINGS (RADIAL LEADS)
C052 (CK05, CKR05)
L
*1.25
MIN.
L
W
H
Lead Dia.
.025
(+.004
-.002)
S
*1.25
MIN.
L
W
C066 (CKR06)
W
L
H
H
.045
MAX.
C062 (CK06, CKR06)
C056 (CKR05)
.026
MIN.
Lead Dia.
.025
(+.004
-.002)
S
*1.25
MIN.
W
.026
MIN.
H
Lead Dia.
.025
(+.004
-.002)
*1.25
MIN.
S
Center Line of leads within .030" of Center Line of case.
Lead Dia.
.025
(+.004
-.002)
S
* Leads are .625 minimum when tape and reel packaged.
DIMENSIONS — INCHES & (MILLIMETERS)
CASE
SIZE
C052/
C056
C062/
C066
MILITARY
EQUIVALENT
STYLES
H
HEIGHT
L
LENGTH
W
WIDTH
S
LEAD
SPACING
CK05, CKR05
.190 ± .010 (4.83 ± .25)
.190 ± .010 (4.83 ± .25)
.090 ± .010 (2.29 ± .25)
.200 ± .015 (5.08 ± .38)
CK06, CKR06
.290 ± .010 (7.37 ± .25)
.290 ± .010 (7.37 ± .25)
.090 ± .010 (2.29 ± .25)
.200 ± .015 (5.08 ± .38)
13
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/MIL-C-11015 (CK) & MIL-PRF-39014 (CKR)
ORDERING INFORMATION
C 052 K 102 K 2 X 5 C A**
CERAMIC
FAILURE RATE
A —
M—
P —
R—
S —
*CASE SIZE
(See Table Below)
SPECIFICATION
Military
T — MIL-PRF-39014
K — MIL-C-11015
Not Applicable (Std.)
1.0%
0.1%
0.01%
0.001%
LEAD MATERIAL
C — Standard
CAPACITANCE
In picofarad code: First two digits are significant
figures and third is number of zeroes following
(except 9 indicates division by 10). Examples:
0.1 ␮F = 100,000 pF = 104 and 9.1 pF = 919.
See tables for Standard Values.
INTERNAL CONSTRUCTION
5 — Standard
CAPACITANCE TOLERANCE
TEMPERATURE CHARACTERISTIC
Standard
M — ±20%
K — ±10%
WORKING
VOLTAGE
Standard tolerances for each Series are
shown in the repetitive parts lists.
*CASE SIZES
RADIAL
AXIAL
C052
C114
C056
C124
C062
C192
C066
C202
C222
1 — 100
2 — 200
5 — 50
KEMET
Military
EIA
Designator Equivalent Equivalent
X
BX
X7R
(Stable)
R
BR
X7R
(Stable)
Capacitance Change With Temp.
Measured Measured
Without
With Bias
Temp.
DC Bias
(Rated
Range, °C
Voltage
Voltage)
-55 to
±15%
+15%
+125
-25%
-55 to
±15%
+15%
+125
-40%
**Part Number Example: C052K102K2X5CA (14 digits – no spaces)
MARKING INFORMATION
C114T (CKR11) THROUGH C222T (CKR16) PER MIL-PRF-39014
C114T (CKR11)
JK
103
KP5
37A
C124T (CKR12)
CKR12
2657J
0537A
31433
J for JAN
K for KEMET
Capacitance
Capacitance Tolerance, FR Level
& Date Code (Yr.)
Date and Lot Code
C192T (CKR14) C202T (CKR15) C222T (CKR16)
Style
Dash No., J for JAN
Date & Lot Code
Source Code
(Federal Supply Code
for Manufacturers,
FSCM)
M39014
5-2125
KEMET
0537A
J50V
105K
Complete Part Number
Manufacturer’s Name
Date & Lot Code
JAN & Voltage
Capacitance, pF Code, Capacitance
Tolerance
C052/56T (CKR05) PER MIL-PRF-39014/01
FRONT
Specification
Sheet No.
Four Digit Part No.
M390
14/01
1579*
BACK
JK
0537
A
JAN-KEMET
Date Code
Lot Code
*Add “V” as the last
digit for stand-off leads.
C062/66T (CKR06) PER MIL-PRF-39014/02
Complete MIL Part No.
Manufacturer’s Name
FRONT
BACK
M39014
2-1338
*KEMET
0537A
J200V
103K
Date & Lot Code
JAN & Voltage
Capacitance, pF Code, Capacitance Tolerance
*Add “V” as the last digit
for stand-off leads.
C114K (CK12) THROUGH C222K (CK16) PER MIL-C-11015
C114K (CK12) C124K (CK13)
KCK
12BX
102K
0537
C192K (CK14) C202K (CK15) C222K (CK16)
KEMET, CK
Style (12 or 13), Temp. Char. (BX or BR)
Capacitance, pF Code, Capacitance Tolerance
Date Code
K100V
CK14BX
123K
0537
KEMET, Voltage
Style (14, 15 or 16), Temp. Char. (BX or BR)
Capacitance, pF Code, Capacitance Tolerance
Date Code
C052K (CK05) PER MIL-C-11015/18 & C062K (CK06) PER MIL-C-11015/19
FRONT
14
Style
Temperature Characteristic
Capacitance, pF Code, Capacitance Tolerance
CK05
BX
102K
BACK
200V
K
0501
Voltage
KEMET
Date Code
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/AXIAL - MIL-C-11015 & MIL-PRF-39014
STABLE TEMPERATURE CHARACTERISTICS - BX & BR (EIA-X7R)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
TOL.
%
10
10
12
15
15
18
22
22
27
33
33
39
47
47
56
68
68
82
100
100
120
150
150
180
220
220
270
330
330
390
470
470
560
680
680
820
1,000
1,000
1,200
1,500
1,500
1,800
2,200
2,200
2,700
3,300
3,300
3,900
4,700
4,700
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
5,600
6,800
6,800
8,200
10,000
10,000
10
10
20
10
10
20
5,600
6,800
6,800
8,200
10,000
10,000
10
10
20
10
10
20
12,000
15,000
15,000
18,000
22,000
22,000
27,000
33,000
33,000
39,000
47,000
47,000
10
10
20
10
10
20
10
10
20
10
10
20
KEMET
PART NUMBER
MIL-C-11015/20
MIL-PRF-39014/05
100 VOLT — C114 SIZE (MILITARY—CK12 or CKR11)
C114(1)100K1X5C(2)
CK12BX100K
CKR11BX100K(2)
C114(1)100M1X5C(2)
CK12BX100M
CKR11BX100M(2)
C114(1)120K1X5C(2)
CK12BX120K
CKR11BX120K(2)
C114(1)150K1X5C(2)
CK12BX150K
CKR11BX150K(2)
C114(1)150M1X5C(2)
CK12BX150M
CKR11BX150M(2)
C114(1)180K1X5C(2)
CK12BX180K
CKR11BX180K(2)
C114(1)220K1X5C(2)
CK12BX220K
CKR11BX220K(2)
C114(1)220M1X5C(2)
CK12BX220M
CKR11BX220M(2)
C114(1)270K1X5C(2)
CK12BX270K
CKR11BX270K(2)
C114(1)330K1X5C(2)
CK12BX330K
CKR11BX330K(2)
C114(1)330M1X5C(2)
CK12BX330M
CKR11BX330M(2)
C114(1)390K1X5C(2)
CK12BX390K
CKR11BX390K(2)
C114(1)470K1X5C(2)
CK12BX470K
CKR11BX470K(2)
C114(1)470M1X5C(2)
CK12BX470M
CKR11BX470M(2)
C114(1)560K1X5C(2)
CK12BX560K
CKR11BX560K(2)
C114(1)680K1X5C(2)
CK12BX680K
CKR11BX680K(2)
C114(1)680M1X5C(2)
CK12BX680M
CKR11BX680M(2)
C114(1)820K1X5C(2)
CK12BX820K
CKR11BX820K(2)
C114(1)101K1X5C(2)
CK12BX101K
CKR11BX101K(2)
C114(1)101M1X5C(2)
CK12BX101M
CKR11BX101M(2)
C114(1)121K1X5C(2)
CK12BX121K
CKR11BX121K(2)
C114(1)151K1X5C(2)
CK12BX151K
CKR11BX151K(2)
C114(1)151M1X5C(2)
CK12BX151M
CKR11BX151M(2)
C114(1)181K1X5C(2)
CK12BX181K
CKR11BX181K(2)
C114(1)221K1X5C(2)
CK12BX221K
CKR11BX221K(2)
C114(1)221M1X5C(2)
CK12BX221M
CKR11BX221M(2)
C114(1)271K1X5C(2)
CK12BX271K
CKR11BX271K(2)
C114(1)331K1X5C(2)
CK12BX331K
CKR11BX331K(2)
C114(1)331M1X5C(2)
CK12BX331M
CKR11BX331M(2)
C114(1)391K1X5C(2)
CK12BX391K
CKR11BX391K(2)
C114(1)471K1X5C(2)
CK12BX471K
CKR11BX471K(2)
C114(1)471M1X5C(2)
CK12BX471M
CKR11BX471M(2)
C114(1)561K1X5C(2)
CK12BX561K
CKR11BX561K(2)
C114(1)681K1X5C(2)
CK12BX681K
CKR11BX681K(2)
C114(1)681M1X5C(2)
CK12BX681M
CKR11BX681M(2)
C114(1)821K1X5C(2)
CK12BX821K
CKR11BX821K(2)
C114(1)102K1X5C(2)
CK12BX102K
CKR11BX102K(2)
C114(1)102M1X5C(2)
CK12BX102M
CKR11BX102M(2)
C114(1)122K1X5C(2)
CK12BX122K
CKR11BX122K(2)
C114(1)152K1X5C(2)
CK12BX152K
CKR11BX152K(2)
C114(1)152M1X5C(2)
CK12BX152M
CKR11BX152M(2)
C114(1)182K1X5C(2)
CK12BX182K
CKR11BX182K(2)
C114(1)222K1X5C(2)
CK12BX222K
CKR11BX222K(2)
C114(1)222M1X5C(2)
CK12BX222M
CKR11BX222M(2)
C114(1)272K1X5C(2)
CK12BX272K
CKR11BX272K(2)
C114(1)332K1X5C(2)
CK12BX332K
CKR11BX332K(2)
C114(1)332M1X5C(2)
CK12BX332M
CKR11BX332M2)
C114(1)392K1X5C(2)
CK12BX392K
CKR11BX392K(2)
C114(1)472K1X5C(2)
CK12BX472K
CKR11BX472K(2)
C114(1)472M1X5C(2)
CK12BX472M
CKR11BX472M2)
50 VOLT — C114 SIZE (MILITARY—CK12 or CKR11)
C114(1)562K5X5C(2)
CK12BX562K
CKR11BX562K(2)
C114(1)682K5X5C(2)
CK12BX682K
CKR11BX682K(2)
C114(1)682M5X5C(2)
CK12BX682M
CKR11BX682M(2)
C114(1)822K5X5C(2)
CK12BX822K
CKR11BX822K(2)
C114(1)103K5X5C(2)
CK12BX103K
CKR11BX103K(2)
C114(1)103M5X5C(2)
CK12BX103M
CKR11BX103M(2)
100 VOLT — C124 SIZE (MILITARY—CK13 or CKR12)
C124(1)562K1X5C(2)
CK13BX562K
CKR12BX562K(2)
C124(1)682K1X5C(2)
CK13BX682K
CKR12BX682K(2)
C124(1)682M1X5C(2)
CK13BX682M
CKR12BX682M(2)
C124(1)822K1X5C(2)
CK13BX822K
CKR12BX822K(2)
C124(1)103K1X5C(2)
CK13BX103K
CKR12BX103K(2)
C124(1)103M1X5C(2)
CK13BX103M
CKR12BX103M(2)
50 VOLT — C124 SIZE (MILITARY—CK13 or CKR12)
C124(1)123K5X5C(2)
CK13BX123K
CKR12BX123K(2)
C124(1)153K5X5C(2)
CK13BX153K
CKR12BX153K(2)
C124(1)153M5X5C(2)
CK13BX153M
CKR12BX153M(2)
C124(1)183K5X5C(2)
CK13BX183K
CKR12BX183K(2)
C124(1)223K5X5C(2)
CK13BX223K
CKR12BX223K(2)
C124(1)223M5X5C(2)
CK13BX223M
CKR12BX223M(2)
C124K273K5R5CA
CK13BR273K
C124K333K5R5CA
CK13BR333K
C124K333M5R5CA
CK13BR333M
C124K393K5R5CA
CK13BR393K
C124K473K5R5CA
CK13BR473K
C124K473M5R5CA
CK13BR473M
MIL-PRF-39014/05 For Failure Rate Levels (2)
M
P
R
S
2601
2602
2603
2604
2605
2606
2607
2608
2609
2610
2611
2612
2613
2614
2615
2616
2617
2618
2619
2620
2621
2622
2623
2624
2625
2626
2627
2628
2629
2630
2631
2632
2633
2634
2635
2636
2637
2638
2639
2640
2641
2642
2643
2644
2645
2646
2647
2648
2649
2650
2801
2802
2803
2804
2805
2806
2807
2808
2809
2810
2811
2812
2813
2814
2815
2816
2817
2818
2819
2820
2821
2822
2823
2824
2825
2826
2827
2828
2829
2830
2831
2832
2833
2834
2835
2836
2837
2838
2839
2840
2841
2842
2843
2844
2845
2846
2847
2848
2849
2850
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
2025
2026
2027
2028
2029
2030
2031
2032
2033
2034
2035
2036
2037
2038
2039
2040
2041
2042
2043
2044
2045
2046
2047
2048
2049
2050
2201
2202
2203
2204
2205
2206
2207
2208
2209
2210
2211
2212
2213
2214
2215
2216
2217
2218
2219
2220
2221
2222
2223
2224
2225
2226
2227
2228
2229
2230
2231
2232
2233
2234
2235
2236
2237
2238
2239
2240
2241
2242
2243
2244
2245
2246
2247
2248
2249
2250
2651
2652
2653
2654
2655
2656
2851
2852
2853
2854
2855
2856
2051
2052
2053
2054
2055
2056
2251
2252
2253
2254
2255
2256
2657
2658
2659
2660
2661
2662
2857
2858
2859
2860
2861
2862
2057
2058
2059
2060
2061
2062
2257
2258
2259
2260
2261
2262
2663
2664
2665
2666
2667
2668
2863
2864
2865
2866
2867
2868
2063
2064
2065
2066
2067
2068
2263
2264
2265
2266
2267
2268
(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014 (2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours,
P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
15
CERAMIC MOLDED/AXIAL - MIL-C-11015 & MIL-PRF-39014
STABLE TEMPERATURE CHARACTERISTICS - BX & BR (EIA-X7R)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
16
TOL.
%
27,000
33,000
33,000
39,000
47,000
47,000
10
10
20
10
10
20
12,000
15,000
15,000
18,000
22,000
22,000
27,000
33,000
33,000
39,000
47,000
47,000
56,000
68,000
68,000
82,000
100,000
100,000
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
56,000
68,000
68,000
82,000
100,000
100,000
120,000
150,000
150,000
180,000
220,000
220,000
270,000
10
10
20
10
10
20
10
10
20
10
10
20
10
56,000
68,000
68,000
82,000
100,000
100,000
120,000
150,000
150,000
180,000
220,000
220,000
270,000
330,000
330,000
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
470,000
470,000
680,000
680,000
1,000,000
1,000,000
10
20
10
20
10
20
470,000
470,000
680,000
680,000
1,000,000
1,000,000
10
20
10
20
10
20
2,200,000
2,200,000
3,300,000
3,300,000
10
20
10
20
KEMET
PART NUMBER
MIL-C-11015/20
MIL-PRF-39014/05
MIL-PRF-39014/05 For Failure Rate Levels (2)
M
P
R
S
50 VOLT — C124 SIZE (MILITARY—CK13 or CKR12) (Cont’d)
C124T273K5X5C(2)
CKR12BX273K(2)
C124T333K5X5C(2)
CKR12BX333K(2)
C124T333M5X5C(2)
CKR12BX333M(2)
C124T393K5X5C(2)
CKR12BX393K(2)
C124T473K5X5C(2)
CKR12BX473K(2)
C124T473M5X5C(2)
CKR12BX473M(2)
100 VOLT — C192 SIZE (MILITARY—CK14 or CKR14)
C192(1)123K1X5C(2)
CK14BX123K
CKR14BX123K(2)
C192(1)153K1X5C(2)
CK14BX153K
CKR14BX153K(2)
C192(1)153M1X5C(2)
CK14BX153M
CKR14BX153M(2)
C192(1)183K1X5C(2)
CK14BX183K
CKR14BX183K(2)
C192(1)223K1X5C(2)
CK14BX223K
CKR14BX223K(2)
C192(1)223M1X5C(2)
CK14BX223M
CKR14BX223M(2)
C192(1)273K1X5C(2)
CK14BX273K
CKR14BX273K(2)
C192(1)333K1X5C(2)
CK14BX333K
CKR14BX333K(2)
C192(1)333M1X5C(2)
CK14BX333M
CKR14BX333M(2)
C192(1)393K1X5C(2)
CK14BX393K
CKR14BX393K(2)
C192(1)473K1X5C(2)
CK14BX473K
CKR14BX473K(2)
C192(1)473M1X5C(2)
CK14BX473M
CKR14BX473M(2)
C192(1)563K1R5C(2)
CK14BR563K
CKR14BR563K(2)
C192(1)683K1R5C(2)
CK14BR683K
CKR14BR683K(2)
C192(1)683M1R5C(2)
CK14BR683M
CKR14BR683M(2)
C192(1)823K1R5C(2)
CK14BR823K
CKR14BR823K(2)
C192(1)104K1R5C(2)
CK14BR104K
CKR14BR104K(2)
C192(1)104M1R5C(2)
CK14BR104M
CKR14BR104M(2)
50 VOLT — C192 SIZE (MILITARY—CK14 or CKR14)
C192T563K5X5C(2)
CKR14BX563K(2)
C192T683K5X5C(2)
CKR14BX683K(2)
C192T683M5X5C(2)
CKR14BX683M(2)
C192T823K5X5C(2)
CKR14BX823K(2)
C192T104K5X5C(2)
CKR14BX104K(2)
C192T104M5X5C(2)
CKR14BX104M(2)
C192(1)124K5R5C(2)
CK14BR124K
CKR14BR124K(2)
C192(1)154K5R5C(2)
CK14BR154K
CKR14BR154K(2)
C192(1)154M5R5C(2)
CK14BR154M
CKR14BR154M(2)
C192(1)184K5R5C(2)
CK14BR184K
CKR14BR184K(2)
C192(1)224K5R5C(2)
CK14BR224K
CKR14BR224K(2)
C192(1)224M5R5C(2)
CK14BR224M
CKR14BR224M(2)
C192(1)274K5R5C(2)
CK14BR274K
CKR14BR274K(2)
100 VOLT — C202 SIZE (MILITARY—CK15 or CKR15)
C202T563K1X5C(2)
CKR15BX563K(2)
C202T683K1X5C(2)
CKR15BX683K(2)
C202T683M1X5C(2)
CKR15BX683M(2)
C202T823K1X5C(2)
CKR15BX823K(2)
C202(1)104K1X5C(2)
CK15BX104K
CKR15BX104K(2)
C202(1)104M1X5C(2)
CK15BX104M
CKR15BX104M(2)
C202(1)124K1R5C(2)
CK15BR124K
CKR15BR124K(2)
C202(1)154K1R5C(2)
CK15BR154K
CKR15BR154K(2)
C202(1)154M1R5C(2)
CK15BR154M
CKR15BR154M(2)
C202(1)184K1R5C(2)
CK15BR184K
CKR15BR184K(2)
C202(1)224K1R5C(2)
CK15BR224K
CKR15BR224K(2)
C202(1)224M1R5C(2)
CK15BR224M
CKR15BR224M(2)
C202(1)274K1R5C(2)
CK15BR274K
CKR15BR274K(2)
C202(1)334K1R5C(2)
CK15BR334K
CKR15BR334K(2)
C202(1)334M1R5C(2)
CK15BR334M
CKR15BR334M(2)
50 VOLT — C202 SIZE (MILITARY—CK15 or CKR15)
C202(1)474K5R5C(2)
CK15BR474K
CKR15BR474K(2)
C202(1)474M5R5C(2)
CK15BR474M
CKR15BR474M(2)
C202T684K5R5C(2)
CKR15BR684K(2)
C202T684M5R5C(2)
CKR15BR684M(2)
C202(1)105K5R5C(2)
CK15BR105K
CKR15BR105K(2)
C202(1)105M5R5C(2)
CK15BR105M
CKR15BR105M(2)
100 VOLT — C222 SIZE (MILITARY—CK16 or CKR16)
C222(1)474K1R5C(2)
CK16BR474K
CKR16BR474K(2)
C222(1)474M1R5C(2)
CK16BR474M
CKR16BR474M(2)
C222T684K1R5C(2)
CKR16BR684K(2)
C222T684M1R5C(2)
CKR16BR684M(2)
C222(1)105K1R5C(2)
CK16BR105K
CKR16BR105K(2)
C222(1)105M1R5C(2)
CK16BR105M
CKR16BR105M(2)
50 VOLT — C222 SIZE (MILITARY—CK16 or CKR16)
C222(1)225K5R5C(2)
CK16BR225K
CKR16BR225K(2)
C222(1)225M5R5C(2)
CK16BR225M
CKR16BR225M(2)
C222(1)335K5R5C(2)
CK16BR335M
CKR16BR335K(2)
C222(1)335M5R5C(2)
CK16BR335M
CKR16BR335M(2)
2669
2670
2671
2672
2673
2674
2869
2870
2871
2872
2873
2874
2069
2070
2071
2072
2073
2074
2269
2270
2271
2272
2273
2274
2675
2676
2677
2678
2679
2680
2681
2682
2683
2684
2685
2686
2693
2694
2695
2696
2697
2698
2875
2876
2877
2878
2879
2880
2881
2882
2883
2884
2885
2886
2893
2894
2895
2896
2897
2898
2075
2076
2077
2078
2079
2080
2081
2082
2083
2084
2085
2086
2093
2094
2095
2096
2097
2098
2275
2276
2277
2278
2279
2280
2281
2282
2283
2284
2285
2286
2293
2294
2295
2296
2297
2298
2687
2688
2689
2690
2691
2692
2699
2700
2701
2702
2703
2704
2705
2887
2888
2889
2890
2891
2892
2899
2900
2901
2902
2903
2904
2905
2087
2088
2089
2090
2091
2092
2099
2100
2101
2102
2103
2104
2105
2287
2288
2289
2290
2291
2292
2299
2300
2301
2302
2303
2304
2305
2706
2707
2708
2709
2710
2711
2712
2713
2714
2715
2716
2717
2718
2719
2720
2906
2907
2908
2909
2910
2911
2912
2913
2914
2915
2916
2917
2918
2919
2920
2106
2107
2108
2109
2110
2111
2112
2113
2114
2115
2116
2117
2118
2119
2120
2306
2307
2308
2309
2310
2311
2312
2313
2314
2315
2316
2317
2318
2319
2320
2721
2722
2723
2724
2725
2726
2921
2922
2923
2924
2925
2926
2121
2122
2123
2124
2125
2126
2321
2322
2323
2324
2325
2326
2727
2728
2729
2730
2731
2732
2927
2928
2929
2930
2931
2932
2127
2128
2129
2130
2131
2132
2327
2328
2329
2330
2331
2332
2733
2734
2735
2736
2933
2934
2935
2936
2133
2134
2135
2136
2333
2334
2335
2336
(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014 (2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours,
P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC MOLDED/RADIAL - MIL-C-11015 & MIL-PRF-39014
STABLE TEMPERATURE CHARACTERISTICS - BX & BR (EIA-X7R)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
TOL.
%
10
10
12
15
15
18
22
22
27
33
33
39
47
47
56
68
68
82
100
100
120
150
150
180
220
220
270
330
330
390
470
470
560
680
680
820
1,000
1,000
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
1,200
1,500
1,500
1,800
2,200
2,200
2,700
3,300
3,300
3,900
4,700
4,700
5,600
6,800
6,800
8,200
10,000
10,000
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
12,000
15,000
15,000
18,000
22,000
22,000
27,000
33,000
33,000
39,000
47,000
47,000
56,000
68,000
68,000
82,000
100,000
100,000
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
KEMET
PART NUMBER
MIL-C-11015/18
MIL-PRF-39014/01
MIL-PRF-39014/01 For Failure Rate Levels (2)
M
P
R
S
200 VOLT — C052/C056 SIZE (MILITARY—CK05 or CKR05)
C05(4)(1)100K2X5C(2)
CK05BX100K
CKR05BX100K(2)(3)
1201(3)
C05(4)(1)100M2X5C(2)
CK05BX100M
CKR05BX100M(2)(3)
1202(3)
C05(4)(1)120K2X5C(2)
CK05BX120K
CKR05BX120K(2)(3)
1203(3)
C05(4)(1)150K2X5C(2)
CK05BX150K
CKR05BX150K(2)(3)
1204(3)
C05(4)(1)150M2X5C(2)
CK05BX150M
CKR05BX150M(2)(3)
1205(3)
C05(4)(1)180K2X5C(2)
CK05BX180K
CKR05BX180K(2)(3)
1206(3)
C05(4)(1)220K2X5C(2)
CK05BX220K
CKR05BX220K(2)(3)
1207(3)
C05(4)(1)220M2X5C(2)
CK05BX220M
CKR05BX220M(2)(3)
1208(3)
C05(4)(1)270K2X5C(2)
CK05BX270K
CKR05BX270K(2)(3)
1209(3)
C05(4)(1)330K2X5C(2)
CK05BX330K
CKR05BX330K(2)(3)
1210(3)
C05(4)(1)330M2X5C(2)
CK05BX330M
CKR05BX330M(2)(3)
1211(3)
C05(4)(1)390K2X5C(2)
CK05BX390K
CKR05BX390K(2)(3)
1212(3)
C05(4)(1)470K2X5C(2)
CK05BX470K
CKR05BX470K(2)(3)
1213(3)
C05(4)(1)470M2X5C(2)
CK05BX470M
CKR05BX470M(2)(3)
1214(3)
C05(4)(1)560K2X5C(2)
CK05BX560K
CKR05BX560K(2)(3)
1215(3)
C05(4)(1)680K2X5C(2)
CK05BX680K
CKR05BX680K(2)(3)
1216(3)
C05(4)(1)680M2X5C(2)
CK05BX680M
CKR05BX680M(2)(3)
1217(3)
C05(4)(1)820K2X5C(2)
CK05BX820K
CKR05BX820K(2)(3)
1218(3)
C05(4)(1)101K2X5C(2)
CK05BX101K
CKR05BX101K(2)(3)
1219(3)
C05(4)(1)101M2X5C(2)
CK05BX101M
CKR05BX101M(2)(3)
1220(3)
C05(4)(1)121K2X5C(2)
CK05BX121K
CKR05BX121K(2)(3)
1221(3)
C05(4)(1)151K2X5C(2)
CK05BX151K
CKR05BX151K(2)(3)
1222(3)
C05(4)(1)151M2X5C(2)
CK05BX151M
CKR05BX151M(2)(3)
1223(3)
C05(4)(1)181K2X5C(2)
CK05BX181K
CKR05BX181K(2)(3)
1224(3)
C05(4)(1)221K2X5C(2)
CK05BX221K
CKR05BX221K(2)(3)
1225(3)
C05(4)(1)221M2X5C(2)
CK05BX221M
CKR05BX221M(2)(3)
1226(3)
C05(4)(1)271K2X5C(2)
CK05BX271K
CKR05BX271K(2)(3)
1227(3)
C05(4)(1)331K2X5C(2)
CK05BX331K
CKR05BX331K(2)(3)
1228(3)
C05(4)(1)331M2X5C(2)
CK05BX331M
CKR05BX331M(2)(3)
1229(3)
C05(4)(1)391K2X5C(2)
CK05BX391K
CKR05BX391K(2)(3)
1230(3)
C05(4)(1)471K2X5C(2)
CK05BX471K
CKR05BX471K(2)(3)
1231(3)
C05(4)(1)471M2X5C(2)
CK05BX471M
CKR05BX471M(2)(3)
1232(3)
C05(4)(1)561K2X5C(2)
CK05BX561K
CKR05BX561K(2)(3)
1233(3)
C05(4)(1)681K2X5C(2)
CK05BX681K
CKR05BX681K(2)(3)
1234(3)
C05(4)(1)681M2X5C(2)
CK05BX681M
CKR05BX681M(2)(3)
1235(3)
C05(4)(1)821K2X5C(2)
CK05BX821K
CKR05BX821K(2)(3)
1236(3)
C05(4)(1)102K2X5C(2)
CK05BX102K
CKR05BX102K(2)(3)
1237(3)
C05(4)(1)102M2X5C(2)
CK05BX102M
CKR05BX102M(2)(3)
1238(3)
100 VOLT — C052/C056 SIZE (MILITARY—CK05 or CKR05)
C05(4)(1)122K1X5C(2)
CK05BX122K
CKR05BX122K(2)(3)
1239(3)
C05(4)(1)152K1X5C(2)
CK05BX152K
CKR05BX152K(2)(3)
1240(3)
C05(4)(1)152M1X5C(2)
CK05BX152M
CKR05BX152M(2)(3)
1441(3)
C05(4)(1)182K1X5C(2)
CK05BX182K
CKR05BX182K(2)(3)
1442(3)
C05(4)(1)222K1X5C(2)
CK05BX222K
CKR05BX222K(2)(3)
1443(3)
C05(4)(1)222M1X5C(2)
CK05BX222M
CKR05BX222M(2)(3)
1444(3)
C05(4)(1)272K1X5C(2)
CK05BX272K
CKR05BX272K(2)(3)
1445(3)
C05(4)(1)332K1X5C(2)
CK05BX332K
CKR05BX332K(2)(3)
1446(3)
C05(4)(1)332M1X5C(2)
CK05BX332M
CKR05BX332M(2)(3)
1447(3)
C05(4)(1)392K1X5C(2)
CK05BX392K
CKR05BX392K(2)(3)
1448(3)
C05(4)(1)472K1X5C(2)
CK05BX472K
CKR05BX472K(2)(3)
1449(3)
C05(4)(1)472M1X5C(2)
CK05BX472M
CKR05BX472M(2)(3)
1450(3)
C05(4)(1)562K1X5C(2)
CK05BX562K
CKR05BX562K(2)(3)
1451(3)
C05(4)(1)682K1X5C(2)
CK05BX682K
CKR05BX682K(2)(3)
1452(3)
C05(4)(1)682M1X5C(2)
CK05BX682M
CKR05BX682M(2)(3)
1453(3)
C05(4)(1)822K1X5C(2)
CK05BX822K
CKR05BX822K(2)(3)
1454(3)
C05(4)(1)103K1X5C(2)
CK05BX103K
CKR05BX103K(2)(3)
1455(3)
C05(4)(1)103M1X5C(2)
CK05BX103M
CKR05BX103M(2)(3)
1456(3)
50 VOLT — C052/C056 SIZE (MILITARY—CK05 or CKR05)
C05(4)(1)123K5X5C(2)
CK05BX123K
CKR05BX123K(2)(3)
1457(3)
C05(4)(1)153K5X5C(2)
CK05BX153K
CKR05BX153K(2)(3)
1458(3)
C05(4)(1)153M5X5C(2)
CK05BX153M
CKR05BX153M(2)(3)
1459(3)
C05(4)(1)183K5X5C(2)
CK05BX183K
CKR05BX183K(2)(3)
1460(3)
C05(4)(1)223K5X5C(2)
CK05BX223K
CKR05BX223K(2)(3)
1461(3)
C05(4)(1)223M5X5C(2)
CK05BX223M
CKR05BX223M(2)(3)
1462(3)
C05(4)(1)273K5X5C(2)
CK05BX273K
CKR05BX273K(2)(3)
1463(3)
C05(4)(1)333K5X5C(2)
CK05BX333K
CKR05BX333K(2)(3)
1464(3)
C05(4)(1)333M5X5C(2)
CK05BX333M
CKR05BX333M(2)(3)
1465(3)
C05(4)(1)393K5X5C(2)
CK05BX393K
CKR05BX393K(2)(3)
1466(3)
C05(4)(1)473K5X5C(2)
CK05BX473K
CKR05BX473K(2)(3)
1467(3)
C05(4)(1)473M5X5C(2)
CK05BX473M
CKR05BX473M(2)(3)
1468(3)
C05(4)(1)563K5X5C(2)
CK05BX563K
CKR05BX563K(2)(3)
1469(3)
C05(4)(1)683K5X5C(2)
CK05BX683K
CKR05BX683K(2)(3)
1470(3)
C05(4)(1)683M5X5C(2)
CK05BX683M
CKR05BX683M(2)(3)
1471(3)
C05(4)(1)823K5X5C(2)
CK05BX823K
CKR05BX823K(2)(3)
1472(3)
C05(4)(1)104K5X5C(2)
CK05BX104K
CKR05BX104K(2)(3)
1473(3)
C05(4)(1)104M5X5C(2)
CK05BX104M
CKR05BX104M(2)(3)
1474(3)
1241(3)
1242(3)
1243(3)
1244(3)
1245(3)
1246(3)
1247(3)
1248(3)
1249(3)
1250(3)
1251(3)
1252(3)
1253(3)
1254(3)
1255(3)
1256(3)
1257(3)
1258(3)
1259(3)
1260(3)
1261(3)
1262(3)
1263(3)
1264(3)
1265(3)
1266(3)
1267(3)
1268(3)
1269(3)
1270(3)
1271(3)
1272(3)
1273(3)
1274(3)
1275(3)
1276(3)
1277(3)
1278(3)
1281(3)
1282(3)
1283(3)
1284(3)
1285(3)
1286(3)
1287(3)
1288(3)
1289(3)
1290(3)
1291(3)
1292(3)
1293(3)
1294(3)
1295(3)
1296(3)
1297(3)
1298(3)
1299(3)
1300(3)
1301(3)
1302(3)
1303(3)
1304(3)
1305(3)
1306(3)
1307(3)
1308(3)
1309(3)
1310(3)
1311(3)
1312(3)
1313(3)
1314(3)
1315(3)
1316(3)
1317(3)
1318(3)
1321(3)
1322(3)
1323(3)
1324(3)
1325(3)
1326(3)
1327(3)
1328(3)
1329(3)
1330(3)
1331(3)
1332(3)
1333(3)
1334(3)
1335(3)
1336(3)
1337(3)
1338(3)
1339(3)
1340(3)
1341(3)
1342(3)
1343(3)
1344(3)
1345(3)
1346(3)
1347(3)
1348(3)
1349(3)
1350(3)
1351(3)
1352(3)
1353(3)
1354(3)
1355(3)
1356(3)
1357(3)
1358(3)
1279(3)
1280(3)
1481(3)
1482(3)
1483(3)
1484(3)
1485(3)
1486(3)
1487(3)
1488(3)
1489(3)
1490(3)
1491(3)
1492(3)
1493(3)
1494(3)
1495(3)
1496(3)
1319(3)
1320(3)
1521(3)
1522(3)
1523(3)
1524(3)
1525(3)
1526(3)
1527(3)
1528(3)
1529(3)
1530(3)
1531(3)
1532(3)
1533(3)
1534(3)
1535(3)
1536(3)
1359(3)
1360(3)
1561(3)
1562(3)
1563(3)
1564(3)
1565(3)
1566(3)
1567(3)
1568(3)
1569(3)
1570(3)
1571(3)
1572(3)
1573(3)
1574(3)
1575(3)
1576(3)
1497(3)
1498(3)
1499(3)
1500(3)
1501(3)
1502(3)
1503(3)
1504(3)
1505(3)
1506(3)
1507(3)
1508(3)
1509(3)
1510(3)
1511(3)
1512(3)
1513(3)
1514(3)
1537(3)
1538(3)
1539(3)
1540(3)
1541(3)
1542(3)
1543(3)
1544(3)
1545(3)
1546(3)
1547(3)
1548(3)
1549(3)
1550(3)
1551(3)
1552(3)
1553(3)
1554(3)
1577(3)
1578(3)
1579(3)
1580(3)
1581(3)
1582(3)
1583(3)
1584(3)
1585(3)
1586(3)
1587(3)
1588(3)
1589(3)
1590(3)
1591(3)
1592(3)
1593(3)
1594(3)
(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014 (2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours,
P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)
(3) Insert “V” for standard design (C056). Leave blank for the flat bottom design (C052).
(4) Insert “2” for standard design (Style C052)
Note: Stand-offs are available only
Insert “6” for stand-off design (Style C056)
with the CKR, not the CK.
}
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
17
CERAMIC MOLDED/RADIAL - MIL-C-11015 & MIL-PRF-39014
STABLE TEMPERATURE CHARACTERISTICS - BX & BR (EIA-X7R)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
TOL.
%
1,200
1,500
1,500
1,800
2,200
2,200
2,700
3,300
3,300
3,900
4,700
4,700
5,600
6,800
6,800
8,200
10,000
10,000
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
12,000
15,000
15,000
18,000
22,000
22,000
27,000
33,000
33,000
39,000
47,000
47,000
56,000
68,000
68,000
82,000
100,000
100,000
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
120,000
150,000
150,000
180,000
220,000
220,000
270,000
330,000
330,000
390,000
470,000
470,000
560,000
680,000
680,000
820,000
1,000,000
1,000,000
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
KEMET
PART NUMBER
MIL-C-11015/19
MIL-PRF-39014/02
MIL-PRF-39014/02 For Failure Rate Levels (2)
M
P
R
S
200 VOLT — C062/C066 SIZE (MILITARY—CK06 or CKR06)
C06(4)(1)122K2X5C(2)
CK06BX122K
CKR06BX122K(2)(3)
1201(3)
C06(4)(1)152K2X5C(2)
CK06BX152K
CKR06BX152K(2)(3)
1202(3)
C06(4)(1)152M2X5C(2)
CK06BX152M
CKR06BX152M(2)(3)
1203(3)
C06(4)(1)182K2X5C(2)
CK06BX182K
CKR06BX182K(2)(3)
1204(3)
C06(4)(1)222K2X5C(2)
CK06BX222K
CKR06BX222K(2)(3)
1206(3)
C06(4)(1)222M2X5C(2)
CK06BX222M
CKR06BX222M(2)(3)
1207(3)
C06(4)(1)272K2X5C(2)
CK06BX272K
CKR06BX272K(2)(3)
1208(3)
C06(4)(1)332K2X5C(2)
CK06BX332K
CKR06BX332K(2)(3)
1209(3)
C06(4)(1)332M2X5C(2)
CK06BX332M
CKR06BX332M(2)(3)
1210(3)
C06(4)(1)392K2X5C(2)
CK06BX392K
CKR06BX392K(2)(3)
1211(3)
C06(4)(1)472K2X5C(2)
CK06BX472K
CKR06BX472K(2)(3)
1212(3)
C06(4)(1)472M2X5C(2)
CK06BX472M
CKR06BX472M(2)(3)
1213(3)
C06(4)(1)562K2X5C(2)
CK06BX562K
CKR06BX562K(2)(3)
1214(3)
C06(4)(1)682K2X5C(2)
CK06BX682K
CKR06BX682K(2)(3)
1215(3)
C06(4)(1)682M2X5C(2)
CK06BX682M
CKR06BX682M(2)(3)
1216(3)
C06(4)(1)822K2X5C(2)
CK06BX822K
CKR06BX822K(2)(3)
1217(3)
C06(4)(1)103K2X5C(2)
CK06BX103K
CKR06BX103K(2)(3)
1218(3)
C06(4)(1)103M2X5C(2)
CK06BX103M
CKR06BX103M(2)(3)
1219(3)
100 VOLT — C062/C066 SIZE (MILITARY—CK06 or CKR06)
C06(4)(1)123K1X5C(2)
CK06BX123K
CKR06BX123K(2)(3)
1231(3)
C06(4)(1)153K1X5C(2)
CK06BX153K
CKR06BX153K(2)(3)
1220(3)
C062K153M1X5CA
CK06BX153M
C06(4)(1)183K1X5C(2)
CK06BX183K
CKR06BX183K(2)(3)
1221(3)
C06(4)(1)223K1X5C(2)
CK06BX223K
CKR06BX223K(2)(3)
1222(3)
C062K223M1X5CA
CK06BX223M
C06(4)(1)273K1X5C(2)
CK06BX273K
CKR06BX273K(2)(3)
1232(3)
C06(4)(1)333K1X5C(2)
CK06BX333K
CKR06BX333K(2)(3)
1223(3)
C062K333M1X5CA
CK06BX333M
C06(4)(1)393K1X5C(2)
CK06BX393K
CKR06BX393K(2)(3)
1224(3)
C06(4)(1)473K1X5C(2)
CK06BX473K
CKR06BX473K(2)(3)
1225(3)
C062K473M1X5CA
CK06BX473M
C06(4)(1)563K1X5C(2)
CK06BX563K
CKR06BX563K(2)(3)
1226(3)
C06(4)(1)683K1X5C(2)
CK06BX683K
CKR06BX683K(2)(3)
1227(3)
C062K683M1X5CA
CK06BX683M
C06(4)(1)823K1X5C(2)
CK06BX823K
CKR06BX823K(2)(3)
1229(3)
C06(4)(1)104K1X5C(2)
CK06BX104K
CKR06BX104K(2)(3)
1230(3)
C062K104M1X5CA
CK06BX104M
50 VOLT — C062/C066 SIZE (MILITARY—CK06 or CKR06)
C06(4)(1)124K5X5C(2)
CK06BX124K
CKR06BX124K(2)(3)
1233(3)
C06(4)(1)154K5X5C(2)
CK06BX154K
CKR06BX154K(2)(3)
1234(3)
C062K154M5X5CA
CK06BX154M
C06(4)(1)184K5X5C(2)
CK06BX184K
CKR06BX184K(2)(3)
1235(3)
C06(4)(1)224K5X5C(2)
CK06BX224K
CKR06BX224K(2)(3)
1236(3)
C062K224M5X5CA
CK06BX224M
C06(4)(1)274K5X5C(2)
CK06BX274K
CKR06BX274K(2)(3)
1237(3)
C06(4)(1)334K5X5C(2)
CK06BX334K
CKR06BX334K(2)(3)
1238(3)
C062K334M5X5CA
CK06BX334M
C06(4)(1)394K5X5C(2)
CK06BX394K
CKR06BX394K(2)(3)
1239(3)
C06(4)(1)474K5X5C(2)
CK06BX474K
CKR06BX474K(2)(3)
1240(3)
C062K474M5X5CA
CK06BX474M
C06(4)(1)564K5X5C(2)
CK06BX564K
CKR06BX564K(2)(3)
1404(3)
C06(4)(1)684K5X5C(2)
CK06BX684K
CKR06BX684K(2)(3)
1405(3)
C062K684M5X5CA
CK06BX684M
C06(4)(1)824K5X5C(2)
CK06BX824K
CKR06BX824K(2)(3)
1406(3)
C06(4)(1)105K5X5C(2)
CK06BX105K
CKR06BX105K(2)(3)
1407(3)
C062K105M5X5CA
CK06BX105M
1241(3)
1242(3)
1243(3)
1244(3)
1246(3)
1247(3)
1248(3)
1249(3)
1250(3)
1251(3)
1252(3)
1253(3)
1254(3)
1255(3)
1256(3)
1257(3)
1258(3)
1259(3)
1281(3)
1282(3)
1283(3)
1284(3)
1286(3)
1287(3)
1288(3)
1289(3)
1290(3)
1291(3)
1292(3)
1293(3)
1294(3)
1295(3)
1296(3)
1297(3)
1298(3)
1299(3)
1321(3)
1322(3)
1323(3)
1324(3)
1326(3)
1327(3)
1328(3)
1329(3)
1330(3)
1331(3)
1332(3)
1333(3)
1334(3)
1335(3)
1336(3)
1337(3)
1338(3)
1339(3)
1271(3)
1260(3)
1311(3)
1300(3)
1351(3)
1340(3)
1261(3)
1262(3)
1301(3)
1302(3)
1341(3)
1342(3)
1272(3)
1263(3)
1312(3)
1303(3)
1352(3)
1343(3)
1264(3)
1265(3)
1304(3)
1305(3)
1344(3)
1345(3)
1266(3)
1267(3)
1306(3)
1307(3)
1346(3)
1347(3)
1269(3)
1270(3)
1309(3)
1310(3)
1349(3)
1350(3)
1273(3)
1274(3)
1313(3)
1314(3)
1353(3)
1354(3)
1275(3)
1276(3)
1315(3)
1316(3)
1355(3)
1356(3)
1277(3)
1278(3)
1317(3)
1318(3)
1357(3)
1358(3)
1279(3)
1280(3)
1319(3)
1320(3)
1359(3)
1360(3)
1408(3)
1409(3)
1412(3)
1413(3)
1416(3)
1417(3)
1410(3)
1411(3)
1414(3)
1415(3)
1418(3)
1419(3)
(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014.
(2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours, P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)
(3) Add “V” for stand-off design (C066). Leave blank for the flat bottom design (C062).
(4) Insert “2” for standard design (Style C062). Insert “6” for stand-off design (Style C066). Note: Stand-offs are available only with the CKR, not the CK.
18
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC LEADED
PACKAGING INFORMATION
Ceramic Axial
Lead Tape and Reel Packaging
Figure 1
KEMET offers standard reeling of Molded and Conformally
Coated Axial Leaded Ceramic Capacitors for automatic insertion
or lead forming machines per EIA specification RS-296. KEMET’S
internal specification four-digit suffix, 7200, is placed at the end of
the part number to designate tape and reel packaging, ie:
C114T103K5X5CR7200.
KEMET
Paper (50 lb.) test minimum is inserted between the layers of
capacitors wound on reels for component pitch ≤ 0.400".
Capacitor lead length may extend only a maximum of .0625"
(1.59mm) beyond the tapes' edges. Capacitors are centered in a
row between the two tapes and will deviate only ± 0.031
(0.79mm) from the row center. A minimum of 36" (91.5 cm) leader
tape is provided at each end of the reel capacitors. Universal
splicing clips are used to connect the tape. Standard reel
quantities are shown on page 21.
KEMET
®
®
Adhesive Tape
Adhesive Tape
Kraft Paper
Interleaving
Figure 2
10.5" - 14"
(26.67 35.56cm)
Figure 3
*
.059" to .315"
Greater Than
Component
Length
.047" Max
(1.20)
Hub
.655" ±0.010"
(16.6 ±0.25)
Table 1
*
3 1 /4 "
(82.6)
1/ "
8
(3.18)
See Table 1 (A)
.250" Nom.
(6.35)
See Table 1
(B)
Dimensions in Inches & (Millimeters)
Component
Body Diameter
Component
Pitch "A"
Inside Tape Spacing "B"
± 1.5mm (0.059")
0.020" or (±0.5mm)
I
0" (0mm) to 0.197" (5mm)
0.197" or (5mm)
2.062" (52.4mm)
0.197" (5.01mm) to 0.394: (10mm)
0.394" or (10mm)
III*
2.874" (73mm)
19
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC LEADED
PACKAGING INFORMATION
Ceramic Radial
Lead Tape and Reel Packaging
KEMET offers standard reeling of Molded and Conformally
Coated Radial Leaded Ceramic Capacitors for automatic
insertion per EIA specification RS-468. Parts are taped to a
tagboard carrier strip, and wound on a reel as shown in
Figure 1. Kraft paper interleaving is inserted between the
layers of capacitors on the reel. Ammopack is also available,
with the same lead tape configuration and package quantities.
12"
(30.48 cm)
*
Figure 1
KEMET
Carrier Strip
.059" to .315"
Greater Than
Over All
Height
of Taped
Components
KEMET
®
®
Adhesive Tape
Hub
.655" ±0.010"
(16.6 ±0.25)
31/4"
(82.6)
1/ "
8
(3.18)
(Note: Non-standard lead lengths
available in bulk only.)
Figure 3: Standard Reel
C056**
C066**
Kraft Paper
Interleaving
Carrier Tape
CK06**
CKR06**
C062**
CK05**
CKR05**
C052**
∆H
P2
P
1MM Max.
(.039")
H1 D0
P1
H
W2
H0
W0
L1
F
T
P0
Figure 2: Lead Tape Configuration (See Table Below)
W
Tape
Carrier
W2
* Lead spacings are 2.54mm
(.10") center-to-center.
** Lead spacings are 5.08mm
(.20") center-to-center.
# See page 15 for exact lead
configuration for Series.
Ceramic Radial Tape and Reel Dimensions in Millimeters & (Inches)
Sprocket Hole Pitch
P0
12.7 (.500)
± 0.3 (.012)
Nominal
Tolerance
Dimension
Symbol
mm (inch)
mm (inch)
H0
Height to Seating
7301
7303
7301
7303
Plane (formed leads) (2)
16.0 (.630) 18.0 (.709) ±0.5 (.020) Minimum
Component Alignment
∆h
4.0 (.157)
±0.2 (.008)
Component Pitch
P
12.7 (.500)
± 0.3 (.012)
Lead Protrusion
L1
1.0 (.039)
Maximum
Lead Spacing (1)
F
5.08
2.54
(.20)
(.10)
3.81
5.08
(.150)
(.200)
6.35 (.250)
+0.6 -0.2
(+.024 -.008)
± 0.7 (.028)
Composite Tape
Thickness
Overall Tape and
Lead Thickness
Carrier Tape Width
t
0.7 (.051)
±0.2 (.008)
T
1.5 (.059)
Maximum
W
18.0 (.709)
Hold-Down Tape
Width
Hold-Down Tape
Location
W0
5.0 (.197)
+1.0 - 0.5
(+.039 -.020)
Minimum
W2
3.0 (.118)
Maximum
Dimension
Sprocket Hole Diameter
Sprocket Hole Center
to Lead Center (1)
Sprocket Hole Center
to Component Center
Height to Seating Plane
(straight leads) (2)
Component Height
Above Tape Center
20
Symbol
Do
P1
P2
H
H1
Nominal
mm (inch)
4.0 (.157)
Tolerance
mm (inch)
± 0.2 (.008)
± 1.3 (.051)
7301
7303
7301
7303
16.0 (.630) 18.0 (.709) ±0.5 (.020) Minimum
32.2 (1.27)
Maximum
(1) Measured at the egress from the carrier tape, on the component side.
(2) Determined by a 4 digit suffix placed at the end of the part number, as follows:
7301 = Recommended for parts with formed leads.
7303 = Recommended for parts with straight leads.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
CERAMIC LEADED
PACKAGING INFORMATION
CERAMIC PACKAGING
KEMET
Series
C114C-K-G
C124C-K-G
C192C-K-G
C202C-K
C222C-K
C052C-K-G
C062C-K-G
C114G
C124G
C192G
C202G
C222G
C052/56G
C062/66G
C512G
C522G
C114T
C124T
C192T
C202T
C222T
C052/56T
C062/66T
Military
Style
CK12,CC75
CK13,CC76
CK14,CC77
CK15
CK16
CK05,CC05
CK06,CC06
CCR75
CCR76
CCR77
CC78-CCR78
CC79-CCR79
CCR05
CCR06
CC07-CCR07
CC08-CCR08
CKR11
CKR12
CKR14
CKR15
CKR16
CKR05
CKR06
Military
Specification
MIL-C-11015/
MIL-PRF-20
MIL-PRF-20
MIL-PRF-39014
Standard (1)
Bulk
Quantity
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
Footnote(2)
Footnote(2)
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
Ammo
Pack
Quantity
2000
1500
Standard
Reel
Quantity
Reel
Size
5000
5000
3000
500
300
2000
1500
5000
5000
3000
500
300
1700
1500
N/A
N/A
5000
5000
3000
500
300
1700
1500
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
N/A
N/A
12"
12"
12"
12"
12"
12"
12"
NOTE:(1)Standardpackagingreferstonumberofpiecesperbag,trayorvial.
(2)Quantityvaries.Forfurtherdetails,pleaseconsultthefactory.
21
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com