CAT24FC256 256K-Bit I2C Serial CMOS EEPROM FEATURES ■ Industrial and automotive ■ Fast mode I2C bus compatible* temperature ranges ■ Max clock frequency: ■ 5 ms max write cycle time - 400kHz for VCC = 1.8 V to 5.5 V - 1MHz for VCC = 2.5 V to 5.5 V ■ Schmitt trigger filtered inputs for noise suppression ■ Low power CMOS technology – Entire array protected when WP at VIH ■ 100,000 program/erase cycles ■ 8-pin DIP or 8-pin SOIC(JEDEC) and 8-pin SOIC ■ Self-timed write cycle with auto-clear (EIAJ) DESCRIPTION The CAT24FC256 is a 256K-bit Serial CMOS EEPROM internally organized as 32,768 words of 8 bits each. Catalyst’s advanced CMOS technology substantially reduces device power requirements. The CAT24FC256 it n DIP Package (P, L, GL) 1 2 8 7 VCC WP 3 4 6 5 SCL SDA o c SOIC Package (J, W, K, X, GW, GX) 1 A1 2 3 4 s i D A2 VSS PIN FUNCTIONS Pin Name 8 7 6 5 d e features a 64-byte page write buffer. The device operates via the I2C bus serial interface and is available in 8pin DIP or 8-pin SOIC packages. u n BLOCK DIAGRAM PIN CONFIGURATION A0 a P ■ 100 year data retention ■ 64-byte page write buffer A0 A1 A2 VSS t r ■ Write protect feature VCC WP SCL SDA EXTERNAL LOAD SENSE AMPS SHIFT REGISTERS DOUT ACK VCC WORD ADDRESS BUFFERS VSS COLUMN DECODERS 512 SDA START/STOP LOGIC XDEC WP 512 EEPROM 512X512 CONTROL LOGIC Function A0, A1, A2 Address Inputs SDA Serial Data/Address SCL Serial Clock WP Write Protect VCC +1.8V to +5.5V Power Supply VSS Ground NC No Connect DATA IN STORAGE HIGH VOLTAGE/ TIMING CONTROL SCL A0 A1 A2 STATE COUNTERS SLAVE ADDRESS COMPARATORS * Catalyst Semiconductor is licensed by Philips Corporation to carry the I2C Bus Protocol. © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 1 Doc. No. 1040, Rev. K CAT24FC256 ABSOLUTE MAXIMUM RATINGS* *COMMENT Temperature Under Bias ................. –55°C to +125°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Storage Temperature ....................... –65°C to +150°C Voltage on Any Pin with Respect to Ground(1) ........... –2.0V to +VCC + 2.0V VCC with Respect to Ground ............... –2.0V to +7.0V Package Power Dissipation Capability (TA = 25°C) ................................... 1.0W t r Lead Soldering Temperature (10 secs) ............ 300°C Output Short Circuit Current(2) ........................ 100mA RELIABILITY CHARACTERISTICS Symbol Parameter (3) Endurance NEND TDR (3) ILTH(3)(4) Reference Test Method Data Retention MIL-STD-883, Test Method 1008 Latch-up JEDEC Standard 17 VCC = 1.8 V to 5.5 V, unless otherwise specified. Parameter ICC1 Power Supply Current - Read ICC2 Power Supply Current - Write ISB(5) Standby Current ILO Output Leakage Current VIL s i D Input Low Voltage VIH VOL2 µA fSCL = 400kHz VCC = 5V 4 mA VIN = GND or VCC VCC = 5V 1 µA VIN = GND to VCC 1 µA VOUT = GND to VCC 1 µA -0.5 VCC x 0.3 V VCC x 0.7 VCC + 0.5 V Output Low Voltage (VCC = +3.0 V) IOL = 3.0 mA 0.4 V Output Low Voltage (VCC = +1.8 V) IOL = 1.5 mA 0.5 V Max Units CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5V Symbol Test CI/O(3) CIN mA 400 fSCL = 100kHz VCC = 5V Typ Years Units Input High Voltage VOL1 Units Max it n o c Input Leakage Current d e 100 Min a P Max Cycles/Byte 100 u n Test Conditions ILI Typ MIL-STD-883, Test Method 1033 100,000 DC OPERATING CHARACTERISTICS Symbol Min (3) Conditions Min Typ Input/Output Capacitance (SDA) VI/O = 0V 8 pF Input Capacitance (SCL, WP, A0, A1) VIN = 0V 6 pF Note: (1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC + 2.0V for periods of less than 20ns. (2) Output shorted for no more than one second. No more than one output shorted at a time. (3) These parameter are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100 and JEDEC test methods. (4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to VCC +1V. (5) Maximum standby current (ISB ) = 10µA for the Automotive and Extended Automotive temperature range. Doc. No. 1040, Rev. K 2 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24FC256 AC CHARACTERISTICS VCC = 1.8V to 5.5 V, unless otherwise specified. Output load is 1 TTL gate and 100pF. Read & Write Cycle Limits Symbol Parameter VCC=1.8V - 5.5V Min FSCL tAA Clock Frequency Max VCC=2.5V - 5.5V Min 400 SCL Low to SDA Data Out and ACK Out 0.05 0.9 0.05 tBUF(2) Time the Bus Must be Free Before a New Transmission Can Start 1.3 0.5 tHD:STA Start Condition Hold Time 0.6 0.25 tLOW Clock Low Period 1.3 0.6 tHIGH Clock High Period 0.6 tSU:STA Start Condition Setup Time (for a Repeated Start Condition) 0.6 tHD:DAT Data In Hold Time tSU:DAT Data In Setup Time d e 0 tR(2) SDA and SCL Rise Time tF(2) SDA and SCL Fall Time tSU:STO it n tDH Data Out Hold Time tWR Write Cycle Time tSP Input Suppresssion (SDA, SCL) o c is tSU;WP WP Setup Time tHD;WP WP Hold Time Power-Up Timing (2)(3) D Symbol tPUR tPUW 0.25 u n 100 Stop Condition Setup Time 0.4 Parameter 0 Max Units 1000 kHz t r 0.5 µs a P 100 µs µs µs µs µs ns ns 20 0.3 0.1 µs 20 300 100 ns 0.6 0.25 µs 50 50 ns 5 5 ms 50 50 ns 0.6 0.5 µs 1.3 0.8 µs Min Typ Max Units Power-Up to Read Operation 1 ms Power-Up to Write Operation 1 ms Note: (1) AC measurement conditions: RL (connects to VCC): 0.3VCC to 0.7 VCC Input rise and fall times: < 50ns Input and output timing reference voltages: 0.5 VCC (2) This parameter is tested initially and after a design or process change that affects the parameter. (3) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. interface circuits are disabled, SDA is allowed to remain high, and the device does not respond to its slave address. The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write cycle, the bus © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 3 Doc. No. 1040, Rev. K CAT24FC256 SDA: Serial Data/Address FUNCTIONAL DESCRIPTION The bidirectional serial data/address pin is used to transfer all data into and out of the device. The SDA pin is an open drain output and can be wire-ORed with other open drain or open collector outputs. The CAT24FC256 supports the I2C Bus data transmission protocol. This Inter-Integrated Circuit Bus protocol defines any device that sends data to the bus to be a transmitter and any device receiving data to be a receiver. The transfer is controlled by the Master device which generates the serial clock and all START and STOP conditions for bus access. The CAT24FC256 operates as a Slave device. Both the Master device and Slave device can operate as either transmitter or receiver, but the Master device controls which mode is activated. WP: Write Protect This input, when tied to GND, allows write operations to the entire memory. When this pin is tied to Vcc, the entire memory is write protected. When left floating, memory is unprotected. These pins are hardwired or left connected. When hardwired, up to eight CAT24FC256's may be addressed on a single bus system. When the pins are left unconnected, the default values are zero. SCL: Serial Clock The serial clock input clocks all data transferred into or out of the device. d e Figure 1. Bus Timing tF tHIGH tR tLOW it n tHD:STA SDA IN tHD:DAT tAA SDA OUT o c Figure 2. Write Cycle Timing is SCL SDA D 8TH BIT u n tLOW SCL tSU:STA t r a P A0, A1, A2: Device Address Inputs PIN DESCRIPTIONS tSU:DAT tSU:STO tBUF tDH ACK BYTE n tWR STOP CONDITION START CONDITION ADDRESS Figure 3. Start/Stop Timing SDA SCL START BIT Doc. No. 1040, Rev. K STOP BIT 4 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24FC256 I2C BUS PROTOCOL as many as eight devices on the same bus. These bits must compare to their hardwired input pins. The last bit of the slave address specifies whether a Read or Write operation is to be performed. When this bit is set to 1, a Read operation is selected, and when set to 0, a Write operation is selected. The features of the I2C bus protocol are defined as follows: (1) Data transfer may be initiated only when the bus is not busy. (2) During a data transfer, the data line must remain stable whenever the clock line is high. Any changes in the data line while the clock line is high will be interpreted as a START or STOP condition. START Condition The START Condition precedes all commands to the device, and is defined as a HIGH to LOW transition of SDA when SCL is HIGH. The CAT24FC256 monitors the SDA and SCL lines and will not respond until this condition is met. DEVICE ADDRESSING it n The bus Master begins a transmission by sending a START condition. The Master sends the address of the particular slave device it is requesting. The four most significant bits of the 8-bit slave address are fixed as 1010 (Fig. 5). The CAT24FC256 uses the next three bits as address bits. The address bits A2, A1 and A0 allow o c Figure 4. Acknowledge Timing s i D SCL FROM MASTER a P Acknowledge After a successful data transfer, each receiving device is required to generate an acknowledge. The Acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. d e STOP Condition A LOW to HIGH transition of SDA when SCL is HIGH determines the STOP condition. All operations must end with a STOP condition. t r After the Master sends a START condition and the slave address byte, the CAT24FC256 monitors the bus and responds with an acknowledge (on the SDA line) when its address matches the transmitted slave address. The CAT24FC256 then performs a Read or Write operation depending on the state of the R/W bit. The CAT24FC256 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8bit byte. u n When the CAT24FC256 begins a READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT24FC256 will continue to transmit 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER ACKNOWLEDGE START Figure 5. Slave Address Bits 1 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 0 1 0 A2 5 A1 A0 R/W Doc. No. 1040, Rev. K CAT24FC256 data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. If the Master transmits more than 64 bytes before sending the STOP condition, the address counter ‘wraps around’, and previously transmitted data will be overwritten. WRITE OPERATIONS When all 64 bytes are received, and the STOP condition has been sent by the Master, the internal programming cycle begins. At this point, all received data is written to the CAT24FC256 in a single write cycle. Byte Write In the Byte Write mode, the Master device sends the START condition and the slave address information (with the R/W bit set to zero) to the Slave device. After the Slave generates an acknowledge, the Master sends two 8-bit address words that are to be written into the address pointers of the CAT24FC256. After receiving another acknowledge from the Slave, the Master device transmits the data to be written into the addressed memory location. The CAT24FC256 acknowledges once more and the Master generates the STOP condition. At this time, the device begins an internal programming cycle to nonvolatile memory. While the cycle is in progress, the device will not respond to any request from the Master device. Disabling of the inputs can be used to take advantage of the typical write cycle time. Once the stop condition is issued to indicate the end of the host's write operation, CAT24FC256 initiates the internal write cycle. ACK polling can be initiated immediately. This involves issuing the start condition followed by the slave address for a write operation. If CAT24FC256 is still busy with the write operation, no ACK will be returned. If CAT24FC256 has completed the write operation, an ACK will be returned and the host can then proceed with the next read or write operation. Page Write The CAT24FC256 writes up to 64 bytes of data, in a single write cycle, using the Page Write operation. The page write operation is initiated in the same manner as the byte write operation, however instead of terminating after the initial byte is transmitted, the Master is allowed to send up to 63 additional bytes. After each byte has been transmitted, CAT24FC256 will respond with an acknowledge, and internally increment the six low order address bits by one. The high order bits remain unchanged. S T A R T is BUS ACTIVITY: MASTER D SDA LINE *=Don't Care Bit S SLAVE ADDRESS A C K d e WRITE PROTECTION it n o c Figure 6. Byte Write Timing t r Acknowledge Polling u n a P The Write Protection feature allows the user to protect against inadvertent programming of the memory array. If the WP pin is tied to VCC, the entire memory array is protected and becomes read only. The CAT24FC256 will accept both slave and byte addresses, but the memory location accessed is protected from programming by the device’s failure to send an acknowledge after the first byte of data is received. BYTE ADDRESS A15–A8 A7–A0 S T O P DATA P * A C K A C K A C K Figure 7. Page Write Timing BUS ACTIVITY: MASTER SDA LINE S T A R T SLAVE ADDRESS BYTE ADDRESS A15–A8 A7–A0 S DATA DATA n S T O P DATA n+63 P * A C K A C K A C K A C K A C K A C K A C K *=Don't Care Bit Doc. No. 1040, Rev. K 6 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24FC256 The READ operation for the CAT24FC256 is initiated in the same manner as the write operation with one exception, that R/W bit is set to one. Three different READ operations are possible: Immediate/Current Address READ, Selective/Random READ and Sequential READ. slave address and byte addresses of the location it wishes to read. After CAT24FC256 acknowledges, the Master device sends the START condition and the slave address again, this time with the R/W bit set to one. The CAT24FC256 then responds with its acknowledge and sends the 8-bit byte requested. The master device does not send an acknowledge but will generate a STOP condition. Immediate/Current Address Read Sequential Read The CAT24FC256’s address counter contains the address of the last byte accessed, incremented by one. In other words, if the last READ or WRITE access was to address N, the READ immediately following would access data from address N+1. If N=E (where E=32767), then the counter will ‘wrap around’ to address 0 and continue to clock out data. After the CAT24FC256 receives its slave address information (with the R/W bit set to one), it issues an acknowledge, then transmits the 8 bit byte requested. The master device does not send an acknowledge, but will generate a STOP condition. The Sequential READ operation can be initiated by either the Immediate Address READ or Selective READ operations. After the CAT24FC256 sends the initial 8-bit byte requested, the Master will respond with an acknowledge which tells the device it requires more data. The CAT24FC256 will continue to output an 8-bit byte for each acknowledge sent by the Master. The operation will terminate when the Master fails to respond with an acknowledge, thus sending the STOP condition. READ OPERATIONS Selective/Random Read Selective/Random READ operations allow the Master device to select at random any memory location for a READ operation. The Master device first performs a ‘dummy’ write operation by sending the START condition, it n Figure 8. Immediate Address Read Timing o c s i D BUS ACTIVITY: MASTER SCL SDA SDA LINE S T A R T d e a P The data being transmitted from CAT24FC256 is outputted sequentially with data from address N followed by data from address N+1. The READ operation address counter increments all of the CAT24FC256 address bits so that the entire memory array can be read during one operation. If more than E (where E=32767) bytes are read out, the counter will ‘wrap around’ and continue to clock out data bytes. u n SLAVE ADDRESS S T O P DATA S P A C K 8 N O A C K 9 8TH BIT DATA OUT © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice t r NO ACK 7 STOP Doc. No. 1040, Rev. K CAT24FC256 Figure 9. Selective Read Timing BUS ACTIVITY: MASTER SDA LINE S T A R T SLAVE ADDRESS S T A R T BYTE ADDRESS A15–A8 A7–A0 * S SLAVE ADDRESS DATA S A C K A C K P A C K A C K *=Don't Care Bit Figure 10. Sequential Read Timing BUS ACTIVITY: MASTER SLAVE ADDRESS DATA n DATA n+1 SDA LINE A C K A C K Doc. No. 1040, Rev. K d e DATA n+2 u n A C K it n o c s i D S T O P 8 A C K N O A C K t r a P S T O P DATA n+x P N O A C K © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24FC256 PACKAGE OUTLINES 8–LEAD 300 MIL WIDE PLASTIC DIP (P, L, GL) 0.245 (6.17) 0.295 (7.49) 0.120 (3.05) 0.150 (3.81) 0.180 (4.57) MAX 0.015 (0.38) — 0.100 (2.54) BSC 0.045 (1.14) 0.060 (1.52) it n 0.014 (0.36) 0.022 (0.56) d e 0.110 (2.79) 0.150 (3.81) u n t r a P 0.300 (7.62) 0.325 (8.26) 0.355 (9.02) 0.400 (10.16) 0.310 (7.87) 0.380 (9.65) Notes: 1. Complies with JEDEC Publication 95 MS001 dimensions; however, some of the dimensions may be more stringent. 2. All linear dimensions are in inches and parenthetically in millimeters. o c s i D © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 9 Doc. No. 1040, Rev. K CAT24FC256 8-LEAD 150 MIL WIDE SOIC (J, W, GW) 0.1890 (4.80) 0.1968 (5.00) 0.149 (3.80) 0.1574 (4.00) 0.0532 (1.35) 0.0688 (1.75) 0.2284 (5.80) 0.2440 (6.20) 0.050 (1.27) BSC 0.013 (0.33) 0.020 (0.51) 0.0099 (0.25) X 45˚ 0.0196 (0.50) 0.0075 (0.19) 0.0098 (0.25) d e 0˚-8˚ 0.016 (0.40) 0.050 (1.27) t r 0.0040 (0.10) 0.0098 (0.25) u n a P Notes: 1. Complies with JEDEC publication 95 MS-012 dimensions; however, some dimensions may be more stringent. 2. All linear dimensions are in inches and parenthetically in millimeters. 3. Lead coplanarity is 0.004" (0.102mm) maximum. it n 8-LEAD 250 MIL WIDE SOIC (K, X, GX) o c s i D 0.0267 (0.68) 0.0303 (0.77) 0.205 (5.20) 0.213 (5.40) 0.205 (5.15) 0.210 (5.35) 0.080 (2.03) MAX 0.303 (7.70) 0.318 (8.10) 0.046 (1.17) 0.054 (1.37) 0.0137 (0.35) 0.0177 (0.45) 0.008 (0.20) 4˚ REF 0.025 (0.65) Notes: 1. All linear dimensions are in inches and parenthetically in millimeters. 2. Lead coplanarity is 0.004" (0.102mm) maximum. Doc. No. 1040, Rev. K 10 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24FC256 ORDERING INFORMATION Prefix CAT Optional Company ID Device # Suffix 24FC256 J -1.8 I Temperature Range I = Industrial (-40˚C to 85˚C) A = Automotive (-40˚C to 105˚C) E = Extended (-40˚C to 125˚C) Product Number Package P: PDIP K: SOIC, EIAJ J: SOIC, JEDEC L: PDIP (Lead-free, Halogen-free) W: SOIC, JEDEC (Lead-free, Halogen-free) X: SOIC, EIAJ (Lead-free, Halogen-free) GL: PDIP (Lead-free, Halogen-free, NiPdAu lead plating) GW: SOIC, JEDEC (Lead-free, Halogen-free, NiPdAu lead plating) GX: SOIC, EIAJ (Lead-free, Halogen-free, NiPdAu lead plating) it n t r Tape & Reel a P Die Revision Operating Voltage Blank: 2.5 to 5.5 V 1.8: 1.8 to 5.5 V d e u n REV-A TE13 Notes: (1) The device used in the above example is a 24FC256JI-1.8TE13 (SOIC, Industrial Temperature, 1.8 Volt to 5.5 Volt Operating Voltage, Tape & Reel) o c s i D © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 11 Doc. No. 1040, Rev. K REVISION HISTORY Date 12/09/03 Revision Comments E Changed Max Clock Frequency from 6.0V to 5.5V in all instances 01/21/04 F Changed Endurance Maximum to 100,000 cycles. 03/13/04 G Eliminated data sheet designation Changed VCC power supply from 1.8V to 6.0V to 1.8V to 5.5V Updated ICC2 Power supply max in DC Operating Characteristics Added package mechanical drawings Eliminated Reel quantity in Ordering Information 05/16/04 H Update Update Update Update Update 06/07/04 I Update Read & Write Cycle Limits 7/28/04 J Update notes on page 2 08/02/05 K Update Pin Configuration Update Ordering Information D.C. Operating Characteristics Read & Write Cycle Limits Ordering Information Revision History Rev Number it n u n d e t r a P Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP ™ AE2 ™ MiniPot™ o c Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. s i D Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. Catalyst Semiconductor, Inc. Corporate Headquarters 1250 Borregas Avenue Sunnyvale, CA 94089 Phone: 408.542.1000 Fax: 408.542.1200 www.caalyst-semiconductor.com Publication #: Revison: Issue date: 1040 K 08/02/05