X7R Dielectric General Specifications X7R formulations are called “temperature stable” ceramics and fall into EIA Class II materials. X7R is the most popular of these intermediate dielectric constant materials. Its temperature variation of capacitance is within ±15% from -55°C to +125°C. This capacitance change is non-linear. Capacitance for X7R varies under the influence of electrical operating conditions such as voltage and frequency. X7R dielectric chip usage covers the broad spectrum of industrial applications where known changes in capacitance due to applied voltages are acceptable. PART NUMBER (see page 2 for complete part number explanation) 0805 5 C 103 M A T Size (L" x W") Voltage 4V = 4 6.3V = 6 10V = Z 16V = Y 25V = 3 50V = 5 100V = 1 200V = 2 500V = 7 Dielectric X7R = C Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros Capacitance Tolerance J = ± 5%* K = ±10% M = ± 20% Failure Rate A = Not Applicable *≤1μF only, contact factory for additional values 2 A Terminations T = Plated Ni and Sn 7 = Gold Plated* Z= FLEXITERM®** Packaging 2 = 7" Reel 4 = 13" Reel 7 = Bulk Cass. 9 = Bulk Special Code A = Std. Product *Optional termination Contact Factory For Multiples **See FLEXITERM® X7R section X7R Dielectric� Typical Temperature Coefficient ⌬ Capacitance vs. Frequency +30 10 +20 % ⌬ Capacitance 0 -5 -10 -15 -20 0 20 40 60 0 -10 -20 -30 1KHz -25 -60 -40 -20 +10 80 100 120 140 Temperature °C 10 KHz 100 KHz 1,000 pF 1210 Impedance, ⍀ Impedance, ⍀ 1.00 0.10 Frequency, MHz 100 0 0 20 40 1000 1.0 0.1 1 10 80 100 120 Variation of Impedance with Chip Size� Impedance vs. Frequency� 100,000 pF - X7R� 10 � � 1206 0805 1210 1.0 0.1 .01 .01 60 Temperature °C Variation of Impedance with Chip Size� Impedance vs. Frequency� 10,000 pF - X7R� � 10 1206 � 0805 10,000 pF 100 10 MHz 1,000 Frequency Variation of Impedance with Cap Value� Impedance vs. Frequency� 1,000 pF vs. 10,000 pF - X7R� 0805� � 10.00 0.01 10 1 MHz Insulation Resistance vs Temperature 10,000 Impedance, ⍀ % Cap Change 5 Insulation Resistance (Ohm-Farads) NOTE: Contact factory for availability of Termination and Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. 100 Frequency, MHz 1,000 1 10 100 1,000 Frequency, MHz 17 X7R Dielectric Specifications and Test Methods Parameter/Test Operating Temperature Range Capacitance Insulation Resistance X7R Specification Limits -55ºC to +125ºC Within specified tolerance ≤ 2.5% for ≥ 50V DC rating ≤ 3.0% for 25V DC rating ≤ 3.5% for 25V and 16V DC rating ≤ 5.0% for ≤ 10V DC rating 100,000MΩ or 1000MΩ - μF, whichever is less Dielectric Strength No breakdown or visual defects Dissipation Factor Resistance to Flexure Stresses Appearance Capacitance Variation Dissipation Factor Insulation Resistance Solderability Resistance to Solder Heat Thermal Shock Load Life Load Humidity 18 Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength No defects ≤ ±12% Measuring Conditions Temperature Cycle Chamber Freq.: 1.0 kHz ± 10% Voltage: 1.0Vrms ± .2V Charge device with rated voltage for 120 ± 5 secs @ room temp/humidity Charge device with 300% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Note: Charge device with 150% of rated voltage for 500V devices. Deflection: 2mm Test Time: 30 seconds 1mm/sec Meets Initial Values (As Above) ≥ Initial Value x 0.3 ≥ 95% of each terminal should be covered with fresh solder No defects, <25% leaching of either end terminal 90 mm Dip device in eutectic solder at 230 ± 5ºC for 5.0 ± 0.5 seconds ≤ ±7.5% Meets Initial Values (As Above) Dip device in eutectic solder at 260ºC for 60 seconds. Store at room temperature for 24 ± 2 hours before measuring electrical properties. Meets Initial Values (As Above) Meets Initial Values (As Above) No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes ≤ ±7.5% Step 2: Room Temp ≤ 3 minutes Meets Initial Values (As Above) Step 3: +125ºC ± 2º 30 ± 3 minutes Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes Meets Initial Values (As Above) Repeat for 5 cycles and measure after 24 ± 2 hours at room temperature No visual defects ≤ ±12.5% ≤ Initial Value x 2.0 (See Above) ≥ Initial Value x 0.3 (See Above) Meets Initial Values (As Above) No visual defects ≤ ±12.5% Charge device with 1.5 rated voltage (≤ 10V) in test chamber set at 125ºC ± 2ºC for 1000 hours (+48, -0) Remove from test chamber and stabilize at room temperature for 24 ± 2 hours before measuring. Store in a test chamber set at 85ºC ± 2ºC/ 85% ± 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. ≤ Initial Value x 2.0 (See Above) ≥ Initial Value x 0.3 (See Above) Meets Initial Values (As Above) Remove from chamber and stabilize at room temperature and humidity for 24 ± 2 hours before measuring. X7R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 0101 0201 0402 0603 0805 1206 Soldering Packaging Reflow Only Paper/Embossed Reflow Only All Paper Reflow/Wave All Paper Reflow/Wave All Paper Reflow/Wave Paper/Embossed Reflow/Wave Paper/Embossed mm (in.) mm (in.) mm (in.) WVDC 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 10 22 47 100 WVDC 0.40 ± 0.02 (0.016 ± 0.0008) 0.20 ± 0.02 (0.008 ± 0.0008) 0.20 ± 0.02 (0.008 ± 0.0008) 10 A A A A A A A 0.60 ± 0.03 (0.024 ± 0.001) 0.30 ± 0.03 (0.011 ± 0.001) 0.15 ± 0.05 (0.006 ± 0.002) 10 16 25 A A A A A A A A A A A A A A A A A A A A A A A A 1.00 ± 0.10 (0.040 ± 0.004) 0.50 ± 0.10 (0.020 ± 0.004) 0.25 ± 0.15 (0.010 ± 0.006) 16 25 50 1.60 ± 0.15 (0.063 ± 0.006) 0.81 ± 0.15 (0.032 ± 0.006) 0.35 ± 0.15 (0.014 ± 0.006) 16 25 50 10 2.01 ± 0.20 (0.079 ± 0.008) 1.25 ± 0.20 (0.049 ± 0.008) 0.50 ± 0.25 (0.020 ± 0.010) 16 25 50 3.20 ± 0.20 (0.126 ± 0.008) 1.60 ± 0.20 (0.063 ± 0.008) 0.50 ± 0.25 (0.020 ± 0.010) 16 25 50 100 J J J J J J J J J J J J J J J J J J N N N N J J J J J J J J J J J J J J J J J J N N N N SIZE 0101 (L) Length (W) Width (t) Terminal Cap (pF) Cap (μF Letter Max. Thickness A 0.33 (0.013) C C C C C C C C 6.3 10 C C C C C C C C C C C C C C C C C C G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G 100 200 G G G G G G G G G G G G G G 6.3 J* J* J* J* J* C 0.56 (0.022) 10 16 25 16 0201 E 0.71 (0.028) PAPER 25 50 6.3 10 0402 G 0.90 (0.035) J 0.94 (0.037) J J J J J J J J J J J J J J J J N N N N 200 J J J J J J J J J J J J N N N N N N N N J J J J J J J J J J J N 6.3 16 25 50 100 200 0603 K 1.02 (0.040) M 1.27 (0.050) 6.3 P* P* 10 J J J J J J J J J J J J J J J M M M Q Q J J J J J J J J J J J J J J M M Q Q Q Q J J J J J J J J J J J J J J P P Q Q Q* Q* Q* Q* Q* Q* Q* Q* Q* 6.3 10 16 25 50 N P* 16 25 50 100 200 10 J J J J J J J J J J J J J J J M M M P Q P* P* 10 J J J J J J J J J J J J J J J J J N N N N N 100 0805 N 1.40 (0.055) P Q 1.52 1.78 (0.060) (0.070) EMBOSSED J J J J J J J J J J J M Q Q Q Q Q Q 200 J J J J J J M M M M P P 500 K K K K M M M M P P Q* 100 200 500 1206 X 2.29 (0.090) Y 2.54 (0.100) Z 2.79 (0.110) *Optional Specifications – Contact factory 19 X7R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED 1210 1812 1825 2220 2225 Reflow Only Paper/Embossed Reflow Only All Embossed Reflow Only All Embossed Reflow Only All Embossed Reflow Only All Embossed 3.20 ± 0.20 (0.126 ± 0.008) 2.50 ± 0.20 (0.098 ± 0.008) 0.50 ± 0.25 (0.020 ± 0.010) 25 50 100 4.50 ± 0.30 (0.177 ± 0.012) 3.20 ± 0.20 (0.126 ± 0.008) 0.61 ± 0.36 (0.024 ± 0.014) 100 200 4.50 ± 0.30 (0.177 ± 0.012) 6.40 ± 0.40 (0.252 ± 0.016) 0.61 ± 0.36 (0.024 ± 0.014) 50 100 5.70 ± 0.40 (0.225 ± 0.016) 5.00 ± 0.40 (0.197 ± 0.016) 0.64 ± 0.39 (0.025 ± 0.015) 50 100 5.72 ± 0.25 (0.225 ± 0.010) 6.35 ± 0.25 (0.250 ± 0.010) 0.64 ± 0.39 (0.025 ± 0.015) 50 100 16 50 J J J J J J J J J J J J J J J M M N N X X X Z Z* J J J J J J J J J J J J J J J M P P Z Z Z Z Z* 10 16 25 J J J J J J J J J J J J J J J M X X Z Z Z Z J J J J J J J J J J J J M P Q Q X Z Z Z J J J J J J J J J J M M Z Z M M M M M M P Q Q K K K K K K K K K K K M M Z Z Z Z 25 200 L W T C 0.56 (0.022) K K K K K K K K K M P Q X Z Z K K K K K K K P P X K P P X Z Z Z M M M M M M M M M M M M M M M M M M M M M M M M M P P X X X X X X X X X X X X X X X X X Z t X X X X X X X X X X X X X X X Z Z X X X X X X X X X X X M M M M M M M M M M M M M M M 100 200 50 P P P P P P P P P P P P P X Z 50 100 200 500 50 1210 A 0.33 (0.013) 500 䉲 J J J J J J J J J J J J J J J M M N N X X X Z Z* E 0.71 (0.028) PAPER *Optional Specifications – Contact factory 20 500 䉲 SIZE Letter Max. Thickness 200 䉲 Cap (μF 10 䉲 Cap (pF) 䉲 (t) Terminal 䉲 (W) Width mm (in.) mm (in.) mm (in.) WVDC 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 10 22 47 100 WVDC 䉲 (L) Length 䉲 SIZE Soldering Packaging G 0.90 (0.035) 100 200 1812 J 0.94 (0.037) K 1.02 (0.040) M 1.27 (0.050) N 1.40 (0.055) 500 50 100 25 1825 P Q 1.52 1.78 (0.060) (0.070) EMBOSSED 50 2220 X 2.29 (0.090) Y 2.54 (0.100) 100 2225 Z 2.79 (0.110)