CLARE CPC1976Y

CPC1976
AC Power Switch
Parameter
AC Operating Voltage
Load Current
On-State Voltage Drop
Blocking Voltage
Rating
20 - 240
2
1.15
600
Units
Vrms
Arms
Vrms (at IL = 2Arms)
VP
Features
•
•
•
•
•
•
•
•
•
•
Load Current up to 2Arms
600VP Blocking Voltage
5mA Sensitivity
Zero-Crossing Detection
DC Control, AC Output
Optically Isolated
TTL and CMOS Compatible
Low EMI and RFI Generation
High Noise Immunity
Machine Insertable, Wave Solderable
CPC1976 is an AC Solid State Switch utilizing
dual power SCR thyristor outputs. This device also
includes zero-cross turn-on circuitry and is specified
with a blocking voltage of 600VP .
In addition, tightly controlled zero-cross circuitry
ensures low noise switching of AC loads by
minimizing the generation of transients. The optically
coupled input and output circuits provide 3750Vrms of
isolation and noise immunity between the control and
load circuits. As a result, the CPC1976 is well suited
for industrial environments where electromagnetic
interference would disrupt the operation of plant facility
communication and control systems.
Approvals
• UL 508 Recognized Component: File #: E69938
• CSA Certified Component: Certificate #: 1172007
Ordering Information
Applications
•
•
•
•
•
•
•
•
•
•
Description
Programmable Control
Process Control
Power Control Panels
Remote Switching
Gas Pump Electronics
Contactors
Large Relays
Solenoids
Motors
Heaters
Part #
CPC1976Y
Description
4-Pin SIP (25/Tube)
Pin Configuration
ZC
1
2
– LED + LED
Pb
RoHS
2002/95/EC
DS-CPC1976-R02
3
4
AC Load AC Load
e3
www.clare.com
1
CPC1976
Absolute Maximum Ratings (@ 25˚ C)
Parameter
Blocking Voltage (VDRM)
Reverse Input Voltage
Input Control Current
Peak (10ms)
Input Power Dissipation 1
Total Power Dissipation 2
Isolation voltage Input to Output
Operational Temperature
Storage Temperature
1
Derate Linearly 1.33 mW / ºC
2
Derate Linearly 20 mW / ºC
Ratings
600
5
50
1
150
2400
3750
-40 to +85
-40 to +125
Units
VP
V
mA
A
mW
mW
Vrms
°C
°C
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
Electrical Characteristcs
Parameters
Output Characteristics @ 25°C
Load Current, Continuous
Maximum Surge Current
Off State Leakage Current
On-State Voltage Drop 1
Critical Rate of Rise
Switching Speeds
Turn-on
Turn-off
Zero-Cross Turn-On Voltage
Holding Current
Latching Current
Operating Frequency 2
Load Power Factor for
Guaranteed Turn-On 3
Input Characteristics @ 25°C
Input Control Current 4
Input Drop-out Voltage
Input Voltage Drop
Reverse Input Current
Common Characteristics @ 25°C
Input to Output Capacitance
Conditions
Symbol
Min
Typ
Max
Units
VL=120-240Vrms
t < 16ms
VDRM
IL=2Arms
-
IL
IPK
0.005
1000
0.86
1200
2
20
1
1.15
-
Arms
A
mA
Vrms
V/μs
tON
tOFF
IH
IL
20
2
0.82
0.84
-
0.5
0.5
10
2
5
6
500
cycles
cycles
V
V
mA
mA
Hz
60Hz
PF
0.25
-
-
-
60Hz
IF=5mA
VR=5V
IF
VF
IR
0.8
0.9
-
1.2
-
5
1.4
10
mA
V
V
μA
-
CI/O
-
-
3
pF
IF = 5 mA
1st half cycle
Subsequent half cycle
-
ILEAK
dv/dt
1
Tested at a peak value equivalent.
Zero Cross 1st half cycle @ <100Hz.
Snubber circuits may be required at low power factors.
4 For high-noise environments, or for high-frequency operation, use I > 10mA.
F
2
3
2
www.clare.com
R02
CPC1976
PERFORMANCE DATA*
25
Device Count (N)
30
Device Count (N)
Typical On-State Voltage Drop
Distribution
(N=50, TA=25ºC, IL=2ADC, IF=5mA)
25
20
15
10
25
20
Device Count (N)
35
Typical LED Forward Voltage Drop
Distribution
(N=50, TA=25ºC, IF=5mA)
15
10
5
LED Current to Operate Distribution
(N=50, TA=25ºC, VL=120VAC/60Hz)
20
15
10
5
5
0
0
Typical Blocking Voltage Distribution
(N=50, TA=25ºC)
15
10
5
810
840 870 900 930
Blocking Voltage (VP)
960
0.72
920
0.70
880
840
800
760
-40
960
20
40
60
Temperature (ºC)
80
164.0
163.5
163.0
-20
0
20
40
60
Temperature (ºC)
80
100
2.1
2.0
1.8
-40
4.0
0.66
0.64
0.62
-20
0
20
40
60
Temperature (ºC)
80
100
20
40
60
Temperature (ºC)
80
100
IL=2AP
0.95
IL=1.5AP
0.90
IL=1AP
0.85
IL=0.5AP
0.80
-20
0
Load Voltage vs. Temperature
(IF=5mA)
1.00
2.2
1.9
162.5
3.6
0.68
1.05
Load Voltage (V)
164.5
2.4
2.8
3.2
LED Current (mA)
Leakage Current
(VL=600VP)
-40
100
2.3
LED current (mA)
Holding Current (μA)
165.5
0
LED Current to Operate
(VL=5V / 60Hz)
2.4
166.0
165.0
2.0
0.60
-20
Holding Current
162.0
-40
1.6
Blocking Voltage vs. Temperature
0
780
0
1.007 1.009 1.011 1.013 1.015 1.017 1.019
On-State Voltage Drop (VP)
1.30
Blocking Voltage (VP)
Device Count (N)
20
1.26
1.27
1.28
1.29
LED Forward Voltage (V)
Leakage Current (μA)
1.25
0.75
-40
-20
0
20
40
60
Temperature (ºC)
80
100
* The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
R02
www.clare.com
3
CPC1976
PERFORMANCE DATA*
1.5
2
1.4
1.3
1.2
1.1
-40
IF=50mA
IF=20mA
IF=10mA
IF=5mA
-20
5.5
1
0
-1
-2
0
20
40
60
Temperature (ºC)
80
-3
-1.5
100
Maximum Non-Repetitive Surge Current
(Values Apply to TJ=50ºC Before Surge)
LED Current to Operate
vs. Load Frequency
(TA=25ºC, VL=137Vrms, ZL=150mH)
6.0
LED Current (mA)
3
Load Current (AP)
LED Forward Voltage (V)
LED Forward Voltage vs. Temperature
1.6
Load Current vs. Load Voltage
(TA=25ºC, IF=5mA)
5.0
4.5
4.0
3.5
3.0
2.5
2.0
-1.0
-0.5
0.0
0.5
Load Voltage (VP)
1.0
0
1.5
100
Typical dv/dt vs. Temperature
200
300
400
Load Frequency (Hz)
500
dv/dt Method
Critical Rate of Rise (V/μs)
Load Current (AP)
25
20
15
10
5
0
1
10 16
100
Time (ms)
1000
1200
Vo
1000
800
Vo = 300V
dv 0.63 x 300V
dt
RC
63%
600
189
RC
In accordance with
EIA/NARM Standards
RS-443 for Solid State Relays
400
200
10%
0
25
50
Temperature (ºC)
85
RC
* The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
4
www.clare.com
R02
MANUFACTURING INFORMATION
Soldering
For proper assembly, the component must be
processed in accordance with the current revision
of IPC/JEDEC standard J-STD-020. Failure to
follow the recommended guidelines may cause
permanent damage to the device resulting in impaired
performance and/or a reduced lifetime expectancy.
Washing
Clare does not recommend ultrasonic cleaning or the
use of chlorinated solvents.
Pb
e3
RoHS
2002/95/EC
MECHANICAL DIMENSIONS
21.082 ± 0.381
(0.830 ± 0.015)
7º TYP
4 PLCS
3.302 ± 0.051
(0.130 ± 0.002)
10.160 ± 0.127
(0.400 ± 0.005)
1.016 ± 0.127
(0.040 ± 0.005)
Pin 1
0.762 ± 0.076
(0.030 ± 0.003)
2.540 ± 0.127
(0.100 ± 0.005)
1.778
(0.070)
10.160 ± 0.127
(0.400 ± 0.005)
Pin 4
4.572 ± 0.127
(0.180 ± 0.005)
0.381 ± 0.013
(0.015 ± 0.0005)
1.651 ± 0.102
(0.065 ± 0.004)
5.080 ± 0.127
(0.200 ± 0.005)
Recommended Hole Pattern
4 x 1.326 (0.052) DIA.
2.540 (0.100)
12.700 (0.500)
17.780 (0.700)
Dimensions
mm
(inches)
Note: Recommended hole size is based on the maximum
cross-section diagonal measure of the pin plus 0.4mm (0.016).
For additional information please visit our website at: www.clare.com
Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of
Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability,
fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental
damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice.
Specification: DS-CPC1976-R02
©Copyright 2009, Clare, Inc.
All rights reserved. Printed in USA.
3/9/09