Date: 9/21/2006 Part No: CT-1205H Unit: mm Description: magnetic buzzer Page No: 1 of 5 Specifications Rated voltage 5.0 Vo-p Operating voltage Mean current 3.0 ~ 7.0 Vo-p 60 mA max. Coil resistance Sound output 47.0 ±7.0 Ω Min. 88 (Typical 92) dBA Rated frequency Operating tempurature Storage tempurature Dimensions Weight Material Terminal RoHS 2,400 Hz -30 ~ +70° C -40 ~ +85° C ø12.8 x W12.8 x H10 mm 2.0 g PPS (S-206) SMD type (Sn Plating) yes Applying rated voltage, 2400 Hz square wave, ½ duty Distance at 10cm (A-weight free air). Applying rated voltage of 2400 Hz, square wave, ½ duty. See attached drawing See attached drawing Frequency Response Curve Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CT-1205H Date: 9/21/2006 Unit: mm Description: magnetic buzzer Page No: 2 of 5 Appearance Drawing Tolerance: ±0.5 Measurement Method Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Date: 9/21/2006 Part No: CT-1205H Unit: mm Description: magnetic buzzer Page No: 3 of 5 Mechanical Characteristics Item Solderability Soldering Heat Resistance Terminal Mechanical Strength Vibration Drop Test Test Condition Lead terminals are immersed in solder bath of +270 ±5°C for 3 ±1 seconds. The product follows the reflow temperature curve to test its reflow thermo stability. Lead pads shall be soldered onto the pc board and the force of 9.8 N (1.0 kg) shall be applied behind the part for 10 seconds. The buzzer will be measured after applying a vibration amplitude of 1.5 mm with 10 to 55 Hz band of vibration frequency to each of the 3 perpendicular directions for 2 hours. The part is to be dropped from a height of 75 cm onto a 40 mm thick wooden board 3 times in 3 axis (X, Y, Z) for a total of 9 drops. Evaluation Standard 95% surface of lead pads must be covered with fresh solder. No in interference in operation. Test Condition The part will be subjected to +85°C for 96 hours. The part will be subjected to -40°C for 96 hours The part will be subjected to 10 cycles. One cycle will consist of: Evaluation Standard No damage or cutting off. After the test, the part shall meet specifications without any damage to the appearance and the SPL should be within ±10 dBA of the initial SPL. Environment Test Item High temp. test Low temp. test Thermal shock Temp./Humidity cycle Phone: 800.275.4899 The part shall be subjected to 10 cycles. One cycle will last for 24 hours and consist of: Fax: 503.612.2381 www.cui.com After the test, the part shall meet specifications without any damage to the appearance or performance. After 4 hours at 25°C, the SPL should be within ±10 dBA of the initial SPL. 20050 SW 112th Ave. Tualatin, OR 97062 Date: 9/21/2006 Part No: CT-1205H Unit: mm Description: magnetic buzzer Page No: 4 of 5 Mechanical Characteristics Item Operating (Life Test) Evaluation Standard Test Condition 1. Continuous life test: The part will be subjected to 72 hours at +55°C After the test, the part shall meet specifications without any with 5 V, 2400 Hz applied. damage to the appearance. After 4 hours at +25°C, the SPL 2. Intermittent life test: should be within ±10 dBA of the A duty cycle of 1 minute on, 1 minute off, a initial SPL. minimum of 10,000 times at room temp (+25±10°C) with 5 V, 2400 Hz applied. Test Conditions Standard Test Condition Judgement Test Condition a) Tempurature: +5 ~ +35°C a) Tempurature: +25±2°C b) Humidity: 45 - 85% b) Humidity: 60 - 70% c) Pressure: 860 - 1060 mbar c) Pressure: 860 - 1060 mbar Recommended Temperature Profile for Reflow Oven Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CT-1205H Date: 9/21/2006 Unit: mm Description: magnetic buzzer Page No: 5 of 5 Recommended Land Pattern Packaging Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062