CXA1100P, CXA1101P/M, CXA1102P/M, CXA1163P/M Dolby∗ B Type Noise Reduction System For the availability of this product, please contact the sales office. Description CXA1100, CXA1101, CXA1102 and CXA1163 are ICs including two separate Dolby B type noise reduction processors. Seven devices with four Dolby levels and two types of package are provided for various applications. These devices feature very few external components, which is achieved by integrated filter circuits using integrated thin film capacitors with high capacitance. 16 pin DIP (Plastic) 16 pin SOP (Plastic) Features • Minimum number of external components • NR ON/OFF and REC/PB switchs included • Small package (DIP16, SOP16) ~ 5.5mA, Typ.) • Small supply current (— • Dual channel processors in one chip Absolute Maximum Ratings (Ta = 25°C) • Supply voltage VCC 17 V • Operating temperature Topr –30 to +85 °C • Storage temperature Tstg –55 to +150 °C • Allowable power dissipation PD DIP16 (A1100P/A1101P/A1102P/A1163P)900 mW SOP16 (A1101M/A1102M/A1163M) 500 mW Note 1) These ICs are available only to the licensees of Dolby Laboratories Licensing Corporation from whom licensing and application information may be obtaind. Note 2) "Dolby" and double D symbols are trade marks of Dolby Laboratories Licensing Corporation. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E90302A13-PP CXA1100/CXA1101/CXA1102/CXA1163 Pin Description No. Symbol (Ta = 25°C, VCC = 12V (Single supply), No signal) Z (in) VDC Description Equivalent Circuit Vcc 1, 16 REC IN 40kΩ 6.0V Recording (Encode) input 1 16 40k Vcc/2 GND 2 VCC — 12.0V Power supply Vcc 3, 14 PB IN 40kΩ 6.0V Playback (Decode) input 3 40k 14 Vcc/2 GND 4 VCC/2 1kΩ Single supply → VCC/2 Split supply → Ground 6.0V Vcc 50µ 150µ Mode control pin for NR ON/OFF 5 ON/OFF — — 5 "H" → NR OFF "L" → NR ON GND Vcc 150 6, 11 LINE OUT — 6.0V 6 Line (Decode) output 11 150 GND –2– CXA1100/CXA1101/CXA1102/CXA1163 No. Symbol Z (in) VDC Description Equivalent Circuit Vcc 4µ 8.2k 7, 10 TC — 0.3V Time constant pin for the level detector 7 10 100k GND Vcc 300 8, 9 REC OUT — 8.2k 6.0V Recording (Encode) output 8 9 300 GND Vcc 50µ 12 REC/PB — — 150µ 12 Mode control pin for REC/PB (Encode/Decode) "H" → B (Decode) "L → EC (Encode) GND Vcc 13 IREF — 1.2V 13 1.2V Reference current input pin for the active filters 10µ GND 15 GND — Single supply → Ground Split supply → VEE 0V –3– CXA1100/CXA1101/CXA1102/CXA1163 Block Diagram REC/PB C12 1µ C14 4.7µ LINE OUT PB IN R1 43k REC IN C11 1µ 15 16 13 14 C13 0.68µ 12 REC OUT 9 10 11 C15 4.7µ ATT1 SC DET SC DET ATT2 ATT3 ATT3 ATT2 ATT1 ATT3 C21 1µ 1 2 REC IN 6 5 4 3 8 7 C1 100µ C25 4.7µ REC OUT C23 0.68µ PB IN LINE OUT C22 1µ C24 4.7µ ATT: Attenuator SC : Side Chain DET: Detector ON/OFF Vcc Test Circuit S3 R P R12 5.1k P OFF R11 5.1k R C12 1µ C11 1µ Audio SG 16 15 14 S5-1 C13 C14 0.68µ 4.7µ R1 43k 13 12 11 10 9 DC Level Meter C16 4.7µ R2 10k 1 2 S6-2 CCIR/ARM Filter 1 1 Vcc A R21 R 5.1k OFF S4 P +15V C21 1µ R22 5.1k 2 3 5 4 6 C1 C22 100µ C24 C2 1µ 4.7µ 100µ S2 OFF ON R5 R3 R4 12k 510 2k P –4– R S1 7 8 2 C23 0.68µ R P C25 4.7µ OFF S6-1 ON S7 AC Level Meter S5-2 Distortion Analyzer CXA1100/CXA1101/CXA1102/CXA1163 Electrical Characteristics Item Symbol Ta = 25°C, Dolby Level: –10dBm ( = 245mVrms) at REC OUT VCC = 15V (CXA1100), VCC = 12V (CXA1101), VCC = 9V (CXA1102) VCC = 6V (CXA1163) Test Condition∗ R/P NR — — f (Hz) Other Conditions Min. Typ. Max. Unit 11.5 8.5 6.5 5.0 — — — — 16.0 16.0 16.0 16.0 V V V V 3.5 3.5 3.5 3.5 5.6 5.5 5.3 5.1 7.5 7.5 7.5 7.5 mA mA mA mA –1.0 –4.0 –7.0 –11.0 0.0 –3.0 –6.0 –10.0 1.0 –2.0 –5.0 –9.0 dBm dBm dBm dBm Operating voltage CXA1100 CXA1101 CXA1102 CXA1163 Vopr Supply current CXA1100 CXA1101 CXA1102 CXA1163 ICC LINE OUT level CXA1100 CXA1101 CXA1102 CXA1163 Vlout REC IN level Vrin R OFF 1k –32 –30 –28 dBm PB IN level Vpin P OFF 1k –32 –30 –28 dBm Encode characteristics (Boost) (1) (2) (3) (4) (5) B-R-1 B-R-2 B-R-3 B-R-4 B-R-5 R R R R R ON ON ON ON ON 500 2k 5k 10k 10k 1.4 5.5 3.9 9.7 –1.1 2.9 7.0 5.4 10.4 0.4 4.4 8.5 6.9 11.9 1.9 dB dB dB dB dB Vomax R OFF 1k 13.5 14.0 14.0 13.0 15.3 15.9 15.9 15.0 — — — — dB dB dB dB Signal handling CXA1100 CXA1101 CXA1102 CXA1163 R R OFF OFF — — Signal Handling ≥ 12dB No signal 1k –25dB –25dB –25dB –40dB 0dB THD = 1% 0dBm = 0.775Vrms –5– CXA1100/CXA1101/CXA1102/CXA1163 Item Total harmonic distortion 1) NR OFF CXA1100 CXA1101 CXA1102 CXA1163 2) NR ON CXA1100 CXA1101 CXA1102 CXA1163 Input impedance REC IN PB IN Encode S/N ratio Crosstalk REC-PB PB-REC REC ch to ch PB ch to ch REC OUT Offset voltage (NR ON — OFF) Control voltage "H" Level "L" Level Symbol Test Condition∗ Min. Typ. Max. Unit — — — — 0.03 0.04 0.05 0.06 0.2 0.2 0.2 0.2 % % % % — — — — 0.03 0.04 0.06 0.09 0.3 0.3 0.3 0.3 % % % % 28 28 40 40 57 57 kΩ kΩ Rg = 5kΩ (CCIR/ARM) 65 69 — dB 0dB 0dB 0dB 0dB — — — — –82 –81 –70 –70 –65 –60 –60 –60 dB dB dB dB — –40 0 40 mV — — 2.5 0 — — VCC 0.5 V V R/P NR THD (OFF) R OFF THD (ON) R Zrec Zpb — — — — 1k 1k SN (CCIR) R ON — CT-1 CT-2 CT-3 CT-4 P R R P OFF OFF OFF OFF 1k 1k 1k 1k Voff R ON VC-H VC-L — — — — ON f (Hz) Other Conditions 1k 1k +10dB +10dB ∗ 0dB means the level which provides the Dolby level at the recording output in the noise reduction off mode. –6– CXA1100/CXA1101/CXA1102/CXA1163 Example of Representative Characteristics Supply Current vs. Input Voltage (CXA1101) Quiescent Current vs. Supply Voltage Encode Mode 0dB = Dolby Level 6.8 Icc — Supply current [mA] Icc — Quiescent current [mA] 6.0 5.6 NR OFF 5.2 4.8 NR ON 4.4 6.4 6.0 5.6 NR OFF 1kHz, 10kHz 5.2 4.0 4.8 NR ON 10kHz 3.6 4.4 NR ON 1kHz 4 6 8 10 12 14 16 –12 0 4 8 Encode Characteristics Temperature Characteristics VCC = 12V 12 VCC = 12V 12 –50dB 10 8 Encode boost [dB] –40dB –30dB 6 4 –20dB 2 500 1k 2k 5k 10k 4 –20dB –10dB 200 500 1k 0dB 5k 10k 20k 2k Frequency [Hz] Frequency [Hz] Signal Handling Load Characteristics (CXA1101) A1163 A1102 A1101 A1100 14 6 20k Encode Mode 20 NR OFF f = 1kHz THD = 1% 18 16 –30dB 0 0dB 200 8 2 –10dB 0 –40dB Ta = –25°C Ta = 25°C Ta = 75°C 10 Maximum output level [dBm] Encode boost [dB] –4 Input level [dB] 12 Signal handling [dB] –8 Vcc — Supply voltage [V] 12 10 Encode Mode 14 VCC = 12V THD = 1% 12 LINE OUT 10 8 REC OUT 6 4 2 8 4 6 8 10 12 14 16 0 Vcc — Supply voltage [V] 1 2 3 4 5 RL — Load resistance [kΩ] –7– 6 7 CXA1100/CXA1101/CXA1102/CXA1163 NR onTot al Harrmonic Dist ort ion-1 (CX A1101) NR off Tot al Harrmonic Dist ort ion-1 (CX A1101) 0.5 1.0 Encode Mode VCC = 12V 0dB = Dolby Level Total Harmonic Disttortion [%] Total Harmonic Disttortion [%] 1.0 0.2 0.1 0.05 0.02 f = 100Hz f = 1kHz f = 10kHz 0.01 –8 –4 0 4 8 12 0.5 Encode Mode VCC = 12V 0dB = Dolby Level 0.2 0.1 0.05 0.02 f = 100Hz f = 1kHz f = 10kHz 0.01 –8 16 –4 Output Level [dB] NR off Tot al Harrmonic Dist ort ion-2 (CX A1100) Total Harmonic Disttortion [%] 0.5 1.0 Encode Mode 0dB = Dolby Level f = 1kHz 0.2 0.1 0.05 0.02 VCC = 15V VCC = 11.5V 0.01 –8 –4 0 4 8 12 0.5 0.2 0.1 0.05 0.02 VCC = 15V VCC = 11.5V 0.01 –8 16 NR off Tot al Harrmonic Dist ort ion-3 (CX A1101) –4 1.0 Encode Mode 0dB = Dolby Level f = 1kHz 0.2 0.1 0.05 0.02 VCC = 15V VCC = 12V VCC = 8.5V 0.01 –8 –4 0 4 8 12 0 4 8 Output Level [dB] 12 16 NR onTot al Harrmonic Dist ort ion-3 (CX A1101) Total Harmonic Disttortion [%] Total Harmonic Disttortion [%] 0.5 16 Encode Mode 0dB = Dolby Level f = 1kHz Output Level [dB] 1.0 12 NR onTot al Harrmonic Dist ort ion-2 (CX A1100) Total Harmonic Disttortion [%] 1.0 0 4 8 Output Level [dB] 0.5 Encode Mode 0dB = Dolby Level f = 1kHz 0.2 0.1 0.05 0.02 VCC = 15V VCC = 12V VCC = 8.5V 0.01 –8 16 Output Level [dB] –4 0 4 8 Output Level [dB] –8– 12 16 CXA1100/CXA1101/CXA1102/CXA1163 NR off Tot al Harmonic Dist ort ion-4 (CX A1102) 0.5 1.0 Encode Mode 0dB = Dolby Level f = 1kHz Total Harmonic Distortion [%] Total Harmonic Distortion [%] 1.0 NR on Tot al Harmonic Dist ort ion-4 (CX A1102) 0.2 0.1 0.05 0.02 VCC = 15V VCC = 9V VCC = 6.5V 0.01 –4 0 4 8 12 0.5 0.2 0.1 0.05 0.02 VCC = 15V VCC = 9V VCC = 6.5V 0.01 –4 20 16 Encode Mode 0dB = Dolby Level f = 1kHz 0 Output Level [dB] Total Harmonic Distortion [%] Total Harmonic Distortion [%] 0.5 1.0 Encode Mode 0dB = Dolby Level f = 1kHz 0.2 0.1 0.05 0.02 VCC = 15V VCC = 6V VCC = 5V 0.01 0 4 8 12 16 0.5 Encode Mode 0dB = Dolby Level f = 1kHz 0.2 0.1 0.05 0.02 VCC = 15V VCC = 6V VCC = 5V 0.01 0 24 20 4 Output Level [dB] 12 16 24 20 REC t o PB and PB t o REC Crosst alk (CX A1101) –30 –30 VCC = 12V/±6V NR off C1 (Pin4) = 100µF –40 –60 Single Supply Crosstalk [dB] –50 Crosstalk [dB] 8 Output Level [dB] Channe l t o Channe l Crosst alk (CX A1101) –40 20 16 NR on Tot al Harmonic Dist ort ion-5 (CX A1163) NR off Tot al Harmonic Dist ort ion-5 (CX A1163) 1.0 4 8 12 Output Level [dB] Encode –70 –50 –60 –70 –80 –80 –90 –90 200 500 Single Supply Decode Split Supply 100 VCC = 12V/±6V NR off C1 (Pin4) = 100µF 1k 2k 5k 10k Split Supply 100 Frequency [Hz] –9– 200 500 1k 2k Frequency [Hz] 5k 10k CXA1100/CXA1101/CXA1102/CXA1163 Ripple Rejection Ratio-1 (CXA1101) Encode Mode VCC = 12V Single Supply Ripple rejection ratio [dB] –20 C1 (Pin4) = 100µF –30 NR on –40 C1 (Pin4) = 470µF –50 NR off C1 (Pin4) = 100µF C1 (Pin4) = 470µF –30 –40 NR on –50 NR off –60 –70 –70 –10 500 1k 2k 5k Decode Mode VCC = 12V Single Supply –20 –60 100 200 Ripple rejection ratio [dB] –10 10k 100 200 500 1k 2k 5k Frequency [Hz] Frequency [Hz] Ripple Rejection Ratio-3 (CXA1101) Ripple Rejection Ratio-4 (CXA1101) VCC Rejection VCC, VEE = ±6V 0 Ripple rejection ratio [dB] Ripple rejection ratio [dB] –10 Ripple Rejection Ratio-2 (CXA1101) –20 Encode Decode –30 –40 NR on –50 NR off –20 –30 –70 –60 1k 2k 5k VEE Rejection VCC, VEE = ±6V –40 –50 500 NR on –10 –60 100 200 Encode Decode NR off 100 200 10k 10k 500 1k 2k 5k 10k Frequency [Hz] Frequency [Hz] Notes on Applications 1) Power supply The CXA1100 Series is basically designed to operate on single ended supply. The split supply operation is also possible, however, VEE (negative) supply should provide low noise and ripple characteristics. The ripple rejection ratio of these devices is generally good for Vcc supply (single ended supply and split supply), however, that for VEE supply is not so good in the NR on mode because the integrated capacitors for the side chain filter are connected to pin 15 (VEE on split supply). – 10 – CXA1100/CXA1101/CXA1102/CXA1163 When the ripple or noise component of VEE supply is not negligible small, the CR filter shown in Fig. a-1 will be usefull. R1 43k 13 The operation voltage range are CXA1100 11.5 to 16V (±5.75 to ±8V) CXA1101 8.5 to 16V (±4.25 to ±8V) CXA1102 6.5 to 16V (±3.25 to ±8V) CXA1163 5.0 to 16V (±2.5 to ±8V) 14 CXA1100 Series 47 VEE 15 100 to 470µF Fig. a-1. The devices will satisfy the signal handling of 12dB specified by Dolby Laboratories on above voltage range. 2) Operation mode control The CXA1100 series provide fully electronic switching circuits. The functions are controlled by DC voltages of the two control pins of REC/PB (pin 12) and ON/OFF (pin 5). The switching truth tables are shown in Fig. a-2. REC/PB VH and VL are defined as (a) Single ended supply operation VCC ≥ VH ≥ 2.5V 0.5V ≥ VL ≥ 0V (b) Split supply operation VCC ≥ VH ≥ VEE + 2.5V VEE + 0.5V ≥ VL ≥ VEE Function VH VL PB (Decode) REC (Encode) ON/OFF VH VL Function NR off NR on Fig. a-2. It is desirable to provide CR time constant circuits at the mode control pins with time constant from 100msec to 1sec, which will reduce switching clicks effectively. 3) Reference levels Characteristics and specifications of the Dolby noise reduction processor are defined as the levels and measured with reference to the Dolby level. This particular level in these devices is –10dBm (245mVrms), and is measured at the recording output (REC OUT) in the NR off mode. The reference levels of the recording input (REC IN), play back input (PB IN) and line output (LINE OUT) are defined the levels which provide the Dolby level at the recording output in the NR off mode. The CXA1100 series has a common silicon die, and has different internal connection. The series provides four different line output levels for various applications. Other reference levels, recording input level, playback input level and recording output level (= Dolby level) are identical in all devices. The reference levels are as follows Recording output level (= Dolby level) Recording input level Play back input level Line output level CXA1100 CXA1101 CXA1102 CXA1163 –10dBm –30dBm –30dBm 0dBm –3dBm –6dBm –10dBm – 11 – (245mVrms) (24.5mVrms) (24.5mVrms) (775mVrms) (548mVrms) (388mVrms) (245mVrms) CXA1100/CXA1101/CXA1102/CXA1163 4) MPX filter termination and C1 for Vcc/2 (Pin 4) The MPX (multiplex) filter termination method shown in Fig. a-3 allows saving the coupling capacitors between the buffer amplifiers and MPX filters. However, the channel to channel separation and REC to PB crosstalk of low frequency signals will be degraded by the termination resistor RT. For example, 5kΩ of R1 will degrade the channel to channel separation to 50dB. Better separation can be obtained by increasing the capacitance of C1 (Pin 4) to 220µF or 470µF. The allowable minimum value of C1 is 47µF, and 100µF is the standard recommended value. Larger values of C1 are generally desirable in order to improve the crosstalk and ripple rejection ratio. 5) Application for dubbing cassette decks The CXA1100 series generates non decoded signal at the recoding output in the decode mode, and can simplify the structure of dubbing decks. See the SONY' Dolby B/C type IC (CX20187/CXA1097Q or CX20188/CXA1098Q) data sheet in detail. Line Input C11 4.7µ MPX Buffer Filter MPX Filter 15 16 RT 14 13 CXA1100 Series RT Line Input MPX Buffer Filter MPX Filter 1 2 3 C21 4.7µ 4 C1 470µ Fig. a-3. Switchable Processor with Single Supply REC PB IN (–30dBm) REC IN (–30dBm) PB C12 1µ C11 1µ VCC REC IN (–30dBm) PB IN (–30dBm) ∗ RT ∗ RT C21 1µ C3 10µ REC/PB C14 4.7µ R2 10k LINE OUT 16 15 14 R1 (12 %) 43k 13 12 1 2 3 4 C2 100µ C13 (10%) 0.68µ 11 10 5 6 7 ∗ C1 100µ C25 4.7µ 8 C23 (10%) 0.68µ REC OUT (–10dBm) LINE OUT NR ON/OFF ∗ C22 1µ 9 REC OUT C15 4.7µ C24 4.7µ OFF ON Note 1) Resistor and capacitor tolerances are ±10% and ±20% respectively unless otherwise specified. Note 2) When resistors RT are connected to Pin 4 for the MPX filter termination, increase the capacitances of C1 and C11 (C21) to 470µF and 4.7µF respectively. – 12 – CXA1100/CXA1101/CXA1102/CXA1163 Switchable Processor with Split Supply REC/PB PB R2 10k REC PB IN (–30dBm) REC IN (–30dBm) C12 1µ C3 10µ C11 1µ R1 (12 %) 43k VEE C1 100µ C2 100µ C14 4.7µ LINE OUT C13 (10%) 0.68µ 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 C15 4.7µ C25 4.7µ VCC C21 1µ REC IN (–30dBm) C22 1µ PB IN (–30dBm) C23 (10%) 0.68µ NR ON/OFF REC OUT (–10dBm) REC OUT (–10dBm) LINE OUT C24 4.7µ ON OFF Note 1) Resistor and capacitor tolerances are ±10% and ±20% respectively unless otherwise specified. Playback Processor with AUX input AUX TAPE ∗ TAPE IN (–30dBm) AUX IN (–30dBm) TAPE/AUX ∗ C14 4.7µ R2 C3 10k 10µ C12 1µ ∗ ∗ LINE OUT R1 (2%) 43k C11 1µ C13 (10%) 0.68µ 16 15 14 13 12 11 10 1 2 3 4 5 6 7 9 VCC AUX IN (–30dBm) TAPE IN (–30dBm) C21 1µ C2 100µ C13 (10%) 0.68µ C1 100µ C22 1µ ∗ 8 NR ON/OFF LINE OUT C24 4.7µ OFF ON Note 1) Resistor and capacitor tolerances are ±10% and ±20% respectively unless otherwise specified. Note 2) When AUX inputs are not necessary, reject R2, C3, C11, C21 and TAPE/AUX switch, and connect Pin 12 to Vcc. – 13 – CXA1100/CXA1101/CXA1102/CXA1163 Package Outline Unit: mm CXA1101P, CXA1101P CXA1102P, CXA1163P 16PIN DIP (PLASTIC) 300mil 16 9 7.62 9 1 + 0.1 0.05 0.25 – + 0.3 6.4 – 0.1 + 0.1 0.05 0.25 – + 0.4 19.1 – 0.1 7.62 16 + 0.3 6.4 – 0.1 + 0.4 19.2 – 0.1 16PIN DIP (PLASTIC) 300mil 0° to 15° 8 1 0° to 15° 2.54 8 0.5 MIN 3.0 MIN 0.5 MIN + 0.4 3.7 – 0.1 3.0 MIN 0.46 ± 0.1 1.53 ± 0.15 PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN DIP-16P-03 LEAD TREATMENT SOLDER PLATING EIAJ CODE ∗DIP016-P-0300-B LEAD MATERIAL COPPER / 42 ALLOY JEDEC CODE Similar to MO-001-AE PACKAGE WEIGHT 1.0g 1.2 ± 0.15 SONY CODE PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE DIP-16P-01 LEAD TREATMENT SOLDER PLATING EIAJ CODE ∗DIP016-P-0300-A LEAD MATERIAL COPPER JEDEC CODE Similar to MO-001-AE PACKAGE WEIGHT 1.0 g CXA1101M, CXA1102M CXA1163M CXA1100P, CXA1101P CXA1102P 16PIN DIP (PLASTIC) 300mil 16PIN SOP (PLASTIC) 300mil + 0.4 1.85 – 0.15 6.35 ± 0.127 + 0.4 9.9 – 0.1 19.35 ± 0.5 16 9 16 9 0° to 10° 7.62 + 0.2 0.1 – 0.05 6.9 + 0.3 5.3 – 0.1 7.9 ± 0.4 0.15 + 0.1 0.28 – 0.06 0.5 ± 0.1 + 0.4 3.7 – 0.1 2.54 1 8 + 0.1 0.2 – 0.05 1.27 3.1 MIN 1.016 0.457 ± 0.076 ± 0.12 M PACKAGE STRUCTURE SONY CODE SOP-16P-L01 EIAJ CODE ∗SOP016-P-0300-A PACKAGE MATERIAL EPOXY RESIN LEAD TREATMENT SOLDER PLATING LEAD MATERIAL COPPER ALLOY PACKAGE WEIGHT 0.2g JEDEC CODE 5.08 MAX 8 0.508 MIN 1 0.45 ± 0.1 0.5 ± 0.2 2.54 ± 0.254 PACKAGE STRUCTURE – 14 – PACKAGE MATERIAL EPOXY RESIN SONY CODE DIP-16P-191 LEAD TREATMENT SOLDER PLATING EIAJ CODE DIP016-P-0300-AU LEAD MATERIAL COPPER JEDEC CODE MS-001-AA PACKAGE WEIGHT 1.0g CXA1100/CXA1101/CXA1102/CXA1163 CXA1100P, CXA1101P/M, CXA1102P/M, CXA1163P/M 16PIN SOP (PLASTIC) 300mil + 0.3 ∗10.2 – 0.1 2.0 MAX 16 9 1 7.8 ± 0.1 + 0.3 ∗5.3 – 0.1 0.05 MIN 1.8 8 0.71 ± 0.1 0.4 ± 0.1 0.15 ± 0.05 0.13 M 0.75 ± 0.2 1.27 ± 0.1 0.15 4° to 8° NOTE: Dimension “∗” does not include mold protrusion. PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE SOP-16P-L122 LEAD TREATMENT SOLDER PLATING EIAJ CODE SOP016-P-0300-BX LEAD MATERIAL COPPER PACKAGE WEIGHT 0.21g JEDEC CODE – 15 –