Data sheet acquired from Cypress Semiconductor Corporation. Data sheet modified to remove devices not offered. CY74FCT16823T CY74FCT162823T 18-Bit Registers SCCS062 - August 1994 - Revised March 2000 Features • FCT-E speed at 4.4 ns • Power-off disable outputs permits live insertion • Edge-rate control circuitry for significantly improved noise characteristics • Typical output skew < 250 ps • ESD > 2000V • TSSOP (19.6-mil pitch) and SSOP (25-mil pitch) packages • Industrial temperature range of −40˚C to +85˚C • VCC = 5V ± 10% CY74FCT16823T Features: • 64 mA sink current, 32 mA source current • Typical VOLP (ground bounce) <1.0V at VCC = 5V, TA = 25˚C CY74FCT162823T Features: • Balanced 24 mA output drivers • Reduced system switching noise • Typical VOLP (ground bounce) <0.6V at VCC = 5V, TA= 25˚C Functional Description The CY74FCT16823T and the CY74FCT162823T 18-bit bus interface registers are designed for use in high-speed, low-power systems needing wide registers and parity. 18-bit operation is achieved by connecting the control lines of the two 9-bit registers. Flow-through pinout and small shrink packaging aids in simplifying board layout. The outputs are designed with a power-off disable feature to allow live insertion of boards. The CY74FCT16823T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162823T has 24-mA balanced output drivers with current limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162823T is ideal for driving transmission lines. Logic Block Diagrams Pin Configuration SSOP/TSSOP Top View 1OE 1CLR 1CLK 1CLKEN R C D 1Q1 1D1 FCT16823-1 TO 8 OTHER CHANNELS 1CLR 1 56 1CLK 1OE 2 55 1CLKEN 1Q1 3 54 1D1 GND 4 53 GND 1Q 2 5 52 1D2 1D3 1Q 3 6 51 VCC 7 50 VCC 1Q4 8 49 1D4 1Q5 9 48 1D5 1Q 6 10 47 1D6 GND 11 46 GND 1Q7 12 45 1 D7 1Q 8 13 44 1 D8 1Q 9 14 43 1D9 2Q1 42 2D1 41 2D2 2OE 2Q2 15 16 2Q3 17 40 2D3 2CLR GND 18 39 GND 2Q4 19 38 2D4 2Q5 20 37 2D5 2Q6 21 36 2D6 VCC 22 35 VCC 2Q7 23 34 2 D7 2Q8 24 25 33 2 D8 GND 32 GND 2CLK 2CLKEN R C D 2Q1 2D2 TO 8 OTHER CHANNELS 2Q9 26 31 2D9 2OE 27 30 2CLKEN 2CLR 28 29 2CLK FCT16823-3 FCT16823-2 Copyright © 2000, Texas Instruments Incorporated CY74FCT16823T CY74FCT162823T Function Table[1] Pin Description Name Inputs Description Outputs Data Inputs OE CLR CLKEN CLK D Q Function CLK Clock Inputs H X X X X Z High Z CLKEN Clock Enable Inputs (Active LOW) L L X X X L Clear X [2] Hold D CLR Asynchronous Clear Inputs (Active LOW) L H H OE Output Enable Inputs (Active LOW) H H L L Z Three-State Outputs H H L H Z L H L L L L H L H H Q X Q Load Maximum Ratings[3, 4] (Above which the useful life may be impaired. For user guidelines, not tested.) Power Dissipation .......................................................... 1.0W Storage Temperature ..................................... −55°C to +125°C Static Discharge Voltage............................................>2001V (per MIL-STD-883, Method 3015) Ambient Temperature with Power Applied .................................................. −55°C to +125°C Operating Range DC Input Voltage .................................................−0.5V to +7.0V Range DC Output Voltage ..............................................−0.5V to +7.0V Industrial DC Output Current (Maximum Sink Current/Pin) ...........................−60 to +120 mA Ambient Temperature VCC −40°C to +85°C 5V ± 10% Notes: 1. H = HIGH Voltage Level. L = LOW Voltage Level. X = Don’t Care. Z = HIGH Impedance. =LOW-to-HIGH transition. 2. Output level before indicated steady-state input conditions were established. 3. Operation beyond the limits set forth may impair the useful life of the device. Unless otherwise noted, these limits are over the operating free-air temperature range. 4. Unused inputs must always be connected to an appropriate logic voltage level, preferably either VCC or ground. 2 CY74FCT16823T CY74FCT162823T Electrical Characteristics Over the Operating Range Parameter Description VIH Input HIGH Voltage VIL Input LOW Voltage Test Conditions Min. Typ.[5] Max. 2.0 V 0.8 [6] VH Input Hysteresis VIK Input Clamp Diode Voltage VCC=Min., IIN=−18 mA IIH Input HIGH Current IIL Unit 100 mV −1.2 V VCC=Max., VI=VCC ±1 µA Input LOW Current VCC=Max., VI=GND ±1 µA IOZH High Impedance Output Current (Three-State Output pins) VCC=Max., VOUT=2.7V ±1 µA IOZL High Impedance Output Current (Three-State Output pins) VCC=Max., VOUT=0.5V ±1 µA IOS Short Circuit Current[7] VCC=Max., VOUT=GND −80 −200 mA Current[7] VCC=Max., VOUT=2.5V −50 −180 mA 1 µA Max. Unit IO IOFF Output Drive Power-Off Disable VCC=0V, −0.7 V −140 VOUT≤4.5V[8] Output Drive Characteristics for CY74FCT16823T Parameter VOH VOL Min. Typ.[5] VCC=Min., IOH=−3 mA 2.5 3.5 VCC=Min., IOH=−15 mA 2.4 3.5 VCC=Min., IOH=−32 mA 2.0 3.0 Description Output HIGH Voltage Output LOW Voltage Test Conditions VCC=Min., IOL=64 mA V 0.2 0.55 V Min. Typ.[5] Output Drive Characteristics for CY74FCT162823T Parameter Max. Unit Output LOW Voltage[7] VCC=5V, VIN=VIH or VIL, VOUT=1.5V 60 115 150 mA IODH Output HIGH Voltage[7] VCC=5V, VIN=VIH or VIL, VOUT=1.5V −60 −115 −150 mA VOH Output HIGH Voltage VCC=Min., IOH=−24 mA 2.4 3.3 VOL Output LOW Voltage VCC=Min., IOL=24 mA IODL Description Test Conditions V 0.3 0.55 V Typ.[5] Capacitance[9] (TA = +25˚C, f = 1.0 MHz) Parameter Description Test Conditions Max. Unit CIN Input Capacitance VIN = 0V 4.5 6.0 pF COUT Output Capacitance VOUT = 0V 5.5 8.0 pF Notes: 5. Typical values are at VCC= 5.0V, TA= +25˚C ambient. 6. This input is specified but not tested. 7. Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or sample and hold techniques are preferable in order to minimize internal chip heating and more accurately reflect operational values. Otherwise prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parametric tests. In any sequence of parameter tests, IOS tests should be performed last. 8. Tested at +25˚C. 9. This parameter is specified but not tested. 3 CY74FCT16823T CY74FCT162823T Power Supply Characteristics Parameter Test Conditions[10] Description Min. Typ.[5] Max. Unit ICC Quiescent Power Supply Current VCC=Max. VIN<0.2V VIN>VCC−0.2V — 5 500 µA ∆ICC Quiescent Power Supply Current (TTL inputs HIGH) VCC=Max. VIN=3.4V[11] — 0.5 1.5 mA ICCD Dynamic Power Supply Current[12] VCC=Max., One Input Toggling, 50% Duty Cycle, Outputs Open, OE=CLKEN=GND VIN=VCC or VIN=GND — 75 120 µA/ MHz IC Total Power Supply Current[13] VCC=Max., f0=10 MHz, 50% Duty Cycle, Outputs Open, One Bit Toggling, OE=CLKEN=GND at f1=5 MHz VIN=VCC or VIN=GND — 0.8 1.7 mA VIN=3.4V or VIN=GND — 1.3 3.2 VCC=Max., at f1=2.5 MHz, 50% Duty Cycle, Outputs Open, Eighteen Bits Toggling, OE=CLKEN=GND f0=10 MHz VIN=VCC or VIN=GND — 4.2 7.1[14] VIN=3.4V or VIN=GND — 9.2 22.1[14] Notes: 10. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 11. Per TTL driven input (VIN=3.4V); all other inputs at VCC or GND. 12. This parameter is not directly testable, but is derived for use in Total Power Supply calculations. = IQUIESCENT + IINPUTS + IDYNAMIC 13. IC IC = ICC+∆ICCDHNT+ICCD(f0/2 + f1N1) ICC = Quiescent Current with CMOS input levels ∆ICC = Power Supply Current for a TTL HIGH input (VIN=3.4V) = Duty Cycle for TTL inputs HIGH DH = Number of TTL inputs at DH NT ICCD = Dynamic Current caused by an input transition pair (HLH or LHL) = Clock frequency for registered devices, otherwise zero f0 = Input signal frequency f1 = Number of inputs changing at f1 N1 All currents are in milliamps and all frequencies are in megahertz. 14. Values for these conditions are examples of the ICC formula. These limits are specified but not tested. 4 CY74FCT16823T CY74FCT162823T Switching Characteristics Over the Operating Range[15] CY74FCT16823AT CY74FCT162823AT Parameter tPLH tPHL Description Condition[16] Min. Max. Unit Fig.No.[16] CL=50 pF RL=500Ω 1.5 10.0 ns 1, 5 CL=300 pF[17] RL=500Ω 1.5 20.0 Propagation Delay CLK to Q tPHL Propagation Delay CLR to Q CL=50 pF RL=500Ω 1.5 14.0 ns 1, 5 tPZH tPZL Output Enable Time OE to Q CL=50 pF RL=500Ω 1.5 12.0 ns 1, 7, 8 CL=300 pF[17] RL=500Ω 1.5 23.0 CL=5 pF[17] RL=500Ω 1.5 7.0 ns 1, 7, 8 CL=50 pF RL=500Ω 1.5 8.0 CL=50 pF RL=500Ω 3.0 — ns 4 tPHZ tPLZ Output Disable Time OE to Q tSU Set-Up Time HIGH or LOW, D to CLK tH Hold Time HIGH or LOW, D to CLK 1.5 — ns 4 tSU Set-Up Time HIGH or LOW, CLKEN to CLK 3.0 — ns 9 tH Hold Time HIGH or LOW CLKEN to CLK 0.0 — ns 9 tW CLK Pulse Width HIGH or LOW 6.0 — ns 5 tW CLR Pulse Width LOW 6.0 — ns 5 tREM Recovery Time CLR to CLK 6.0 — ns 6 — 0.5 ns — tSK(O) Output Skew[18] Switching Characteristics Over the Operating Range[15] CY74FCT16823CT CY74FCT16823ET CY74FCT162823CT CY74FCT162823ET Parameter tPLH tPHL Description Propagation Delay CLK to Q Condition[16] Min. Max. Min. Max. Unit Fig.No.[16] CL=50 pF RL=500Ω 1.5 6.0 1.5 4.4 ns 1, 5 CL=300 pF[17] RL=500Ω 1.5 12.5 1.5 8.0 tPHL Propagation Delay CLR to Q CL=50 pF RL=500Ω 1.5 6.1 1.5 4.4 ns 1, 5 tPZH tPZL Output Enable Time OE to Q CL=50 pF RL=500Ω 1.5 5.5 1.5 4.4 ns 1, 7, 8 CL=300 pF[17] RL=500Ω 1.5 12.5 1.5 9.0 CL=5 pF[17] RL=500Ω 1.5 5.2 1.5 3.6 ns 1, 7, 8 CL=50 pF RL=500Ω 1.5 6.5 1.5 3.6 tPHZ tPLZ Output Disable Time OE to Q 5 CY74FCT16823T CY74FCT162823T Switching Characteristics Over the Operating Range[15] (continued) CY74FCT16823CT CY74FCT16823ET CY74FCT162823CT CY74FCT162823ET Parameter Description Condition[16] Min. Max. Min. Max. Unit Fig.No.[16] CL=50 pF RL=500Ω 2.0 — 1.5 — ns 4 tSU Set-Up Time HIGH or LOW, D to CLK tH Hold Time HIGH or LOW, D to CLK 1.5 — 0.0 — ns 4 tSU Set-Up Time HIGH or LOW, CLKEN to CLK 3.0 — 2.5 — ns 9 tH Hold Time HIGH or LOW CLKEN to CLK 0.0 — 0.0 — ns 9 tW CLK Pulse Width HIGH or LOW 3.3 — 3.3 — ns 5 tW CLR Pulse Width LOW 3.3 — 3.0 — ns 5 tREM Recovery Time CLR to CLK 6.0 — 3.0 — ns 6 tSK(O) Output Skew[18] — 0.5 — 0.5 ns — Notes: 15. Minimum limits are specified but not tested on Propagation Delays. 16. See “Parameter Measurement Information” in the General Information section. 17. These limits are specified but not tested. 18. Skew between any two outputs of the same package switching in the same direction. This parameter is ensured by design. Ordering Information CY74FCT16823 Speed (ns) 4.4 6.0 10.0 Ordering Code Package Name Package Type CY74FCT16823ETPACT Z56 56-Lead (240-Mil) TSSOP CY74FCT16823ETPVC/PVCT O56 56-Lead (300-Mil) SSOP CY74FCT16823CTPACT Z56 56-Lead (240-Mil) TSSOP CY74FCT16823CTPVC/PVCT O56 56-Lead (300-Mil) SSOP CY74FCT16823ATPACT Z56 56-Lead (240-Mil) TSSOP Operating Range Industrial Industrial Industrial Ordering Information CY74FCT162823 Speed (ns) 4.4 6.0 10.0 Ordering Code Package Name Package Type 74FCT162823ETPACT Z56 56-Lead (240-Mil) TSSOP CY74FCT162823ETPVC O56 56-Lead (300-Mil) SSOP 74FCT162823ETPVCT O56 56-Lead (300-Mil) SSOP 74FCT162823CTPACT Z56 56-Lead (240-Mil) TSSOP CY74FCT162823CTPVC O56 56-Lead (300-Mil) SSOP 74FCT162823CTPVCT O56 56-Lead (300-Mil) SSOP 74FCT162823ATPACT Z56 56-Lead (240-Mil) TSSOP 6 Operating Range Industrial Industrial Industrial CY74FCT16823T CY74FCT162823T Package Diagrams 56-Lead Shrunk Small Outline Package O56 56-Lead Thin Shrunk Small Outline Package Z56 7 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated