CYPRESS CY7C1392JV18

CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
18-Mbit DDR-II SIO SRAM 2-Word
Burst Architecture
Features
Functional Description
■
18- Mbit Density (2M x 8, 2M x 9, 1M x 18, 512K x 36)
■
300 MHz Clock for High Bandwidth
■
2-word Burst for reducing Address Bus Frequency
■
Double Data Rate (DDR) Interfaces
(data transferred at 600 MHz) at 300 MHz
■
Two Input Clocks (K and K) for Precise DDR Timing
❐ SRAM uses rising edges only
■
Two Input Clocks for Output Data (C and C) to Minimize Clock
Skew and Flight Time mismatches
■
Echo Clocks (CQ and CQ) simplify Data Capture in High Speed
Systems
■
Synchronous Internally Self-timed Writes
■
DDR-II operates with 1.5 cycle Read Latency when the DLL is
enabled
■
Operates similar to a DDR-I Device with one Cycle Read
Latency in DLL Off Mode
■
1.8V Core Power Supply with HSTL Inputs and Outputs
■
Variable Drive HSTL Output Buffers
■
Expanded HSTL Output Voltage (1.4V–VDD)
■
Available in 165-Ball FBGA Package (13 x 15 x 1.4 mm)
■
Offered in both Pb-free and non Pb-free packages
■
JTAG 1149.1 compatible Test Access Port
■
Delay Lock Loop (DLL) for Accurate Data Placement
The CY7C1392JV18, CY7C1992JV18, CY7C1393JV18, and
CY7C1394JV18 are 1.8V Synchronous Pipelined SRAMs,
equipped with Double Data Rate Separate IO (DDR-II SIO)
architecture. The DDR-II SIO consists of two separate ports: the
read port and the write port to access the memory array. The
read port has data outputs to support read operations and the
write port has data inputs to support write operations. The DDR-II
SIO has separate data inputs and data outputs to completely
eliminate the need to ‘turnaround’ the data bus required with
common IO devices. Access to each port is accomplished
through a common address bus. Addresses for read and write
are latched on alternate rising edges of the input (K) clock. Write
data is registered on the rising edges of both K and K. Read data
is driven on the rising edges of C and C if provided, or on the
rising edge of K and K if C or C is not provided. Each address
location is associated with two 8-bit words in the case of
CY7C1392JV18, two 9-bit words in the case of CY7C1992JV18,
two 18-bit words in the case of CY7C1393JV18, and two 36-bit
words in the case of CY7C1394JV18 that burst sequentially into
or out of the device.
Asynchronous inputs include an output impedance matching
input (ZQ). Synchronous data outputs are tightly matched to the
two output echo clocks CQ/CQ, eliminating the need to capture
data separately from each individual DDR-II SIO SRAM in the
system design. Output data clocks (C/C) enable maximum
system clocking and data synchronization flexibility.
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K/K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.
Configurations
CY7C1392JV18 – 2M x 8
CY7C1992JV18 – 2M x 9
CY7C1393JV18 – 1M x 18
CY7C1394JV18 – 512K x 36
Selection Guide
Description
Maximum Operating Frequency
Maximum Operating Current
Cypress Semiconductor Corporation
Document #: 001-44698 Rev. *A
•
300 MHz
250 MHz
Unit
300
250
MHz
mA
x8
820
700
x9
825
700
x18
865
725
x36
935
770
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised August 22, 2008
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Logic Block Diagram (CY7C1392JV18)
K
K
CLK
Gen.
DOFF
LD
LD
Control
Logic
R/W
C
Read Data Reg.
16
R/W
VREF
Read Add. Decode
Address
Register
Write
Data Reg
1M x 8 Array
20
Write
Data Reg
1M x 8 Array
A(19:0)
8
Write Add. Decode
D[7:0]
Control
Logic
C
CQ
8
8
Reg.
Reg. 8
Reg.
8
NWS[1:0]
CQ
8
Q[7:0]
Logic Block Diagram (CY7C1992JV18)
K
K
CLK
Gen.
DOFF
LD
LD
Control
Logic
R/W
C
Read Data Reg.
18
R/W
VREF
Read Add. Decode
Address
Register
Write
Data Reg
1M x 9 Array
20
Write
Data Reg
1M x 9 Array
A(19:0)
9
Write Add. Decode
D[8:0]
Control
Logic
BWS[0]
Document #: 001-44698 Rev. *A
C
CQ
9
9
Reg.
Reg. 9
Reg.
9
CQ
9
Q[8:0]
Page 2 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Logic Block Diagram (CY7C1393JV18)
K
K
CLK
Gen.
DOFF
LD
LD
Control
Logic
R/W
C
Read Data Reg.
C
CQ
36
R/W
VREF
Read Add. Decode
Address
Register
Write
Data Reg
512K x 18 Array
19
Write
Data Reg
512K x 18 Array
A(18:0)
18
Write Add. Decode
D[17:0]
18
Control
Logic
18
Reg.
Reg. 18
Reg.
18
BWS[1:0]
CQ
18
Q[17:0]
Logic Block Diagram (CY7C1394JV18)
K
K
CLK
Gen.
DOFF
LD
LD
Control
Logic
R/W
C
Read Data Reg.
C
CQ
72
R/W
VREF
Read Add. Decode
Address
Register
Write
Data Reg
256K x 18 Array
18
Write
Data Reg
256K x 18 Array
A(17:0)
36
Write Add. Decode
D[35:0]
36
Control
Logic
BWS[3:0]
Document #: 001-44698 Rev. *A
36
Reg.
Reg. 36
Reg.
36
CQ
36
Q[35:0]
Page 3 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Pin Configuration
The pin configurations for CY7C1392JV18, CY7C1992JV18, CY7C1393JV18, and CY7C1394JV18 follow. [1]
165-Ball FBGA (13 x 15 x 1.4 mm) Pinout
CY7C1392JV18 (2M x 8)
1
2
3
4
5
6
7
8
9
10
11
A
CQ
NC/72M
A
R/W
NWS1
K
NC/144M
LD
A
NC/36M
CQ
B
NC
NC
NC
A
NC/288M
K
NWS0
A
NC
NC
Q3
C
NC
NC
NC
VSS
A
A
A
VSS
NC
NC
D3
D
NC
D4
NC
VSS
VSS
VSS
VSS
VSS
NC
NC
NC
E
NC
NC
Q4
VDDQ
VSS
VSS
VSS
VDDQ
NC
D2
Q2
F
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
G
NC
D5
Q5
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
H
DOFF
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
Q1
D1
K
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
L
NC
Q6
D6
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
Q0
M
NC
NC
NC
VSS
VSS
VSS
VSS
VSS
NC
NC
D0
N
NC
D7
NC
VSS
A
A
A
VSS
NC
NC
NC
P
NC
NC
Q7
A
A
C
A
A
NC
NC
NC
R
TDO
TCK
A
A
A
C
A
A
A
TMS
TDI
CY7C1992JV18 (2M x 9)
1
2
3
4
5
6
7
8
9
10
11
A
CQ
NC/72M
A
R/W
NC
K
NC/144M
LD
A
NC/36M
CQ
B
NC
NC
NC
A
NC/288M
K
BWS0
A
NC
NC
Q4
C
NC
NC
NC
VSS
A
A
A
VSS
NC
NC
D4
D
NC
D5
NC
VSS
VSS
VSS
VSS
VSS
NC
NC
NC
E
NC
NC
Q5
VDDQ
VSS
VSS
VSS
VDDQ
NC
D3
Q3
F
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
G
NC
D6
Q6
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
H
DOFF
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
Q2
D2
K
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
L
NC
Q7
D7
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
Q1
M
NC
NC
NC
VSS
VSS
VSS
VSS
VSS
NC
NC
D1
N
NC
D8
NC
VSS
A
A
A
VSS
NC
NC
NC
P
NC
NC
Q8
A
A
C
A
A
NC
D0
Q0
R
TDO
TCK
A
A
A
C
A
A
A
TMS
TDI
Note
1. NC/36M, NC/72M, NC/144M, and NC/288M are not connected to the die and can be tied to any voltage level.
Document #: 001-44698 Rev. *A
Page 4 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Pin Configuration
(continued)
The pin configurations for CY7C1392JV18, CY7C1992JV18, CY7C1393JV18, and CY7C1394JV18 follow. [1]
165-Ball FBGA (13 x 15 x 1.4 mm) Pinout
CY7C1393JV18 (1M x 18)
1
2
3
NC/144M NC/36M
4
5
6
7
8
9
10
11
R/W
BWS1
K
NC/288M
LD
A
NC/72M
CQ
A
CQ
B
NC
Q9
D9
A
NC
K
BWS0
A
NC
NC
Q8
C
NC
NC
D10
VSS
A
A
A
VSS
NC
Q7
D8
D
NC
D11
Q10
VSS
VSS
VSS
VSS
VSS
NC
NC
D7
E
NC
NC
Q11
VDDQ
VSS
VSS
VSS
VDDQ
NC
D6
Q6
F
NC
Q12
D12
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
Q5
G
NC
D13
Q13
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
D5
H
DOFF
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
D14
VDDQ
VDD
VSS
VDD
VDDQ
NC
Q4
D4
K
NC
NC
Q14
VDDQ
VDD
VSS
VDD
VDDQ
NC
D3
Q3
L
NC
Q15
D15
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
Q2
M
NC
NC
D16
VSS
VSS
VSS
VSS
VSS
NC
Q1
D2
N
NC
D17
Q16
VSS
A
A
A
VSS
NC
NC
D1
P
NC
NC
Q17
A
A
C
A
A
NC
D0
Q0
R
TDO
TCK
A
A
A
C
A
A
A
TMS
TDI
9
10
CY7C1394JV18 (512K x 36)
1
2
4
5
6
7
8
R/W
BWS2
K
BWS1
LD
D18
A
BWS3
K
BWS0
A
D17
Q17
Q8
Q28
D19
VSS
A
A
A
VSS
D16
Q7
D8
D28
D20
Q19
VSS
VSS
VSS
VSS
VSS
Q16
D15
D7
Q29
D29
Q20
VDDQ
VSS
VSS
VSS
VDDQ
Q15
D6
Q6
Q30
Q21
D21
VDDQ
VDD
VSS
VDD
VDDQ
D14
Q14
Q5
G
D30
D22
Q22
VDDQ
VDD
VSS
VDD
VDDQ
Q13
D13
D5
H
DOFF
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
D31
Q31
D23
VDDQ
VDD
VSS
VDD
VDDQ
D12
Q4
D4
K
Q32
D32
Q23
VDDQ
VDD
VSS
VDD
VDDQ
Q12
D3
Q3
L
Q33
Q24
D24
VDDQ
VSS
VSS
VSS
VDDQ
D11
Q11
Q2
M
D33
Q34
D25
VSS
VSS
VSS
VSS
VSS
D10
Q1
D2
N
D34
D26
Q25
VSS
A
A
A
VSS
Q10
D9
D1
P
Q35
D35
Q26
A
A
C
A
A
Q9
D0
Q0
R
TDO
TCK
A
A
A
C
A
A
A
TMS
TDI
A
CQ
B
Q27
Q18
C
D27
D
E
F
3
NC/288M NC/72M
Document #: 001-44698 Rev. *A
11
NC/36M NC/144M
CQ
Page 5 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Pin Definitions
Pin Name
IO
Pin Description
D[x:0]
InputData Input Signals. Sampled on the rising edge of K and K clocks during valid write operations.
Synchronous CY7C1392JV18 - D[7:0]
CY7C1992JV18 - D[8:0]
CY7C1393JV18 - D[17:0]
CY7C1394JV18 - D[35:0]
LD
InputSynchronous Load. This input is brought LOW when a bus cycle sequence is defined. This definition
Synchronous includes address and read/write direction. All transactions operate on a burst of 2 data (one clock period
of bus activity).
Nibble Write Select 0, 1 − Active LOW (CY7C1392JV18 Only). Sampled on the rising edge of the K
and K clocks during Write operations. Used to select which nibble is written into the device during the
current portion of the Write operations. Nibbles not written remain unaltered.
NWS0 controls D[3:0] and NWS1 controls D[7:4].
All Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select
ignores the corresponding nibble of data and is not written into the device.
NWS0,
NWS1
BWS0,
BWS1,
BWS2,
BWS3
InputByte Write Select 0, 1, 2 and 3 − Active LOW. Sampled on the rising edge of the K and K clocks during
Synchronous write operations. Used to select which byte is written into the device during the current portion of the write
operations. Bytes not written remain unaltered.
CY7C1992JV18 − BWS0 controls D[8:0]
CY7C1393JV18 − BWS0 controls D[8:0], BWS1 controls D[17:9].
CY7C1394JV18 − BWS0 controls D[8:0], BWS1 controls D[17:9],BWS2 controls D[26:18] and BWS3 controls
D[35:27].
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select
ignores the corresponding byte of data and is not written into the device.
A
InputAddress Inputs. Sampled on the rising edge of the K clock during active read and write operations. These
Synchronous address inputs are multiplexed for both read and write operations. Internally, the device is organized as
2M x 8 (2 arrays each of 1M x 8) for CY7C1392JV18, 2M x 9 (2 arrays each of 1M x 9) for CY7C1992JV18,
1M x 18 (2 arrays each of 512K x 18) for CY7C1393JV18, and 512K x 36 (2 arrays each of 256K x 36)
for CY7C1394JV18. Therefore, only 20 address inputs are needed to access the entire memory array of
CY7C1392JV18 and CY7C1992JV18, 19 address inputs for CY7C1393JV18, and 18 address inputs for
CY7C1394JV18. These inputs are ignored when the appropriate port is deselected.
Q[x:0]
OutputsData Output Signals. These pins drive out the requested data during a read operation. Valid data is
Synchronous driven out on the rising edge of both the C and C clocks during read operations, or K and K when in single
clock mode. When the read port is deselected, Q[x:0] are automatically tri-stated.
CY7C1392JV18 − Q[7:0]
CY7C1992JV18 − Q[8:0]
CY7C1393JV18 − Q[17:0]
CY7C1394JV18 − Q[35:0]
R/W
InputSynchronous Read/Write Input. When LD is LOW, this input designates the access type (read when
Synchronous R/W is HIGH, write when R/W is LOW) for the loaded address. R/W must meet the setup and hold times
around the edge of K.
C
Input Clock
Positive Input Clock for Output Data. C is used in conjunction with C to clock out the read data from
the device. C and C are used together to deskew the flight times of various devices on the board back to
the controller. See Application Example on page 9 for further details.
C
Input Clock
Negative Input Clock for Output Data. C is used in conjunction with C to clock out the read data from
the device. C and C are used together to deskew the flight times of various devices on the board back to
the controller. See Application Example on page 9 for further details.
K
Input Clock
Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device
and to drive out data through Q[x:0] when in single clock mode. All accesses are initiated on the rising
edge of K.
K
Input Clock
Negative Input Clock Input. K is used to capture synchronous inputs being presented to the device and
to drive out data through Q[x:0] when in single clock mode.
Document #: 001-44698 Rev. *A
Page 6 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Pin Definitions
Pin Name
(continued)
IO
Pin Description
CQ
Echo Clock
CQ Referenced with Respect to C. This is a free running clock and is synchronized to the input clock
for output data (C) of the DDR-II. In the single clock mode, CQ is generated with respect to K. The timings
for the echo clocks are shown in the table Switching Characteristics on page 22.
CQ
Echo Clock
CQ Referenced with Respect to C. This is a free running clock and is synchronized to the input clock
for output data (C) of the DDR-II. In the single clock mode, CQ is generated with respect to K. The timings
for the echo clocks are shown in the table Switching Characteristics on page 22.
ZQ
Input
Output Impedance Matching Input. This input is used to tune the device outputs to the system data bus
impedance. CQ, CQ, and Q[x:0] output impedance are set to 0.2 x RQ, where RQ is a resistor connected
between ZQ and ground. Alternatively, this pin is connected directly to VDDQ, which enables the minimum
impedance mode. This pin cannot be connected directly to GND or left unconnected.
DOFF
Input
DLL Turn Off − Active Low. Connecting this pin to ground turns off the DLL inside the device. The timing
in the DLL turned off operation differs from those listed in this data sheet. For normal operation, this pin
is connected to a pull up through a 10 Kohm or less pull up resistor. The device behaves in DDR-I mode
when the DLL is turned off. In this mode, the device can be operated at a frequency of up to 167 MHz
with DDR-I timing.
TDO
Output
TCK
Input
TCK Pin for JTAG.
TDI
Input
TDI Pin for JTAG.
TMS
Input
TMS Pin for JTAG.
NC
N/A
Not Connected to the Die. Can be tied to any voltage level.
NC/36M
N/A
Not Connected to the Die. Can be tied to any voltage level.
NC/72M
N/A
Not Connected to the Die. Can be tied to any voltage level.
NC/144M
N/A
Not Connected to the Die. Can be tied to any voltage level.
NC/288M
N/A
Not Connected to the Die. Can be tied to any voltage level.
VREF
VDD
VSS
VDDQ
InputReference
TDO for JTAG.
Reference Voltage Input. Static input used to set the reference level for HSTL inputs, Outputs, and AC
measurement points.
Power Supply Power Supply Inputs to the Core of the Device.
Ground
Ground for the Device.
Power Supply Power Supply Inputs for the Outputs of the Device.
Document #: 001-44698 Rev. *A
Page 7 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Functional Overview
The CY7C1392JV18, CY7C1992JV18, CY7C1393JV18, and
CY7C1394JV18 are synchronous pipelined Burst SRAMs
equipped with a DDR-II Separate IO interface, which operates
with a read latency of one and half cycles when DOFF pin is tied
HIGH. When DOFF pin is set LOW or connected to VSS the
device behaves in DDR-I mode with a read latency of one clock
cycle.
Accesses are initiated on the rising edge of the positive input
clock (K). All synchronous input timing is referenced from the
rising edge of the input clocks (K and K) and all output timing is
referenced to the rising edge of the output clocks (C/C, or K/K
when in single clock mode).
All synchronous data inputs (D[x:0]) pass through input registers
controlled by the rising edge of the input clocks (K and K). All
synchronous data outputs (Q[x:0]) pass through output registers
controlled by the rising edge of the output clocks (C/C or K/K
when in single-clock mode).
All synchronous control (R/W, LD, BWS[0:X]) inputs pass through
input registers controlled by the rising edge of the input clock (K).
CY7C1393JV18 is described in the following sections. The same
basic descriptions apply to CY7C1392JV18, CY7C1992JV18,
and CY7C1394JV18.
Read Operations
The CY7C1393JV18 is organized internally as two arrays of
512K x 18. Accesses are completed in a burst of two sequential
18-bit data words. Read operations are initiated by asserting
R/W HIGH and LD LOW at the rising edge of the positive input
clock (K). The address presented to address inputs is stored in
the read address register. Following the next K clock rise, the
corresponding lowest order 18-bit word of data is driven onto the
Q[17:0] using C as the output timing reference. On the
subsequent rising edge of C, the next 18-bit data word is driven
onto the Q[17:0]. The requested data is valid 0.45 ns from the
rising edge of the output clock (C/C, or K/K when in single clock
mode). Read accesses are initiated on every rising edge of the
positive input clock (K). This pipelines the data flow such that
data is transferred out of the device on every rising edge of the
output clocks, C/C (or K/K when in single clock mode).
The CY7C1393JV18 first completes the pending read
transactions, when read access is deselected. Synchronous
internal circuitry automatically tri-states the output following the
next rising edge of the positive output clock (C).
Write Operations
Write operations are initiated by asserting R/W LOW and LD
LOW at the rising edge of the positive input clock (K). The
address presented to address inputs is stored in the write
address register. On the following K clock rise the data presented
to D[17:0] is latched and stored into the 18-bit write data register,
provided BWS[1:0] are both asserted active. On the subsequent
rising edge of the negative input clock (K) the information
presented to D[17:0] is also stored into the write data register,
provided BWS[1:0] are both asserted active. The 36 bits of data
are then written into the memory array at the specified location.
Document #: 001-44698 Rev. *A
Write accesses are initiated on every rising edge of the positive
input clock (K). This pipelines the data flow such that 18 bits of
data can be transferred into the device on every rising edge of
the input clocks (K and K).
When Write access is deselected, the device ignores all inputs
after the pending write operations are completed.
Byte Write Operations
Byte write operations are supported by the CY7C1393JV18. A
write operation is initiated as described in the section Write
Operations on page 8. The bytes that are written are determined
by BWS0 and BWS1, which are sampled with each set of 18-bit
data words. Asserting the appropriate Byte Write Select input
during the data portion of a write latches the data being
presented and writes it into the device. Deasserting the Byte
Write Select input during the data portion of a write enables the
data stored in the device for that byte to remain unaltered. This
feature is used to simplify read, modify, and write operations to
a byte write operation.
Single Clock Mode
The CY7C1393JV18 is used with a single clock that controls
both the input and output registers. In this mode the device
recognizes only a single pair of input clocks (K and K) that control
both the input and output registers. This operation is identical to
the operation if the device had zero skew between the K/K and
C/C clocks. All timing parameters remain the same in this mode.
To use this mode of operation, tie C and C HIGH at power on.
This function is a strap option and not alterable during device
operation.
DDR Operation
The CY7C1393JV18 enables high performance operation
through high clock frequencies (achieved through pipelining) and
double data rate mode of operation.
If a read occurs after a write cycle, address and data for the write
are stored in registers. Store the write information because the
SRAM cannot perform the last word write to the array without
conflicting with the read. The data stays in this register until the
next write cycle occurs. On the first write cycle after the reads,
the stored data from the earlier write is written into the SRAM
array. This is called a posted write.
Depth Expansion
Depth expansion requires replicating the LD control signal for
each bank. All other control signals are common between banks
as appropriate.
Programmable Impedance
Connect an external resistor, RQ, between the ZQ pin on the
SRAM and VSS to enable the SRAM to adjust its output driver
impedance. The value of RQ is five times the value of the
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15 percent is between 175Ω and 350Ω, with VDDQ = 1.5V.
The output impedance is adjusted every 1024 cycles at power
up to account for drifts in supply voltage and temperature.
Page 8 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Echo Clocks
DLL
Echo clocks are provided on the DDR-II to simplify data capture
on high-speed systems. Two echo clocks are generated by the
DDR-II. CQ is referenced with respect to C and CQ is referenced
with respect to C. These are free running clocks and are synchronized to the output clock of the DDR-II. In the single clock mode,
CQ is generated with respect to K and CQ is generated with
respect to K. The timing for the echo clocks is shown in Switching
Characteristics on page 22.
These chips use a Delay Lock Loop (DLL) that is designed to
function between 120 MHz and the specified maximum clock
frequency. During power up, when the DOFF is tied HIGH, the
DLL is locked after 1024 cycles of stable clock. The DLL is also
reset by slowing or stopping the input clocks K and K for a
minimum of 30 ns. However, it is not necessary to reset the DLL
to lock it to the desired frequency. The DLL automatically locks
1024 clock cycles after a stable clock is presented. Disable the
DLL by applying ground to the DOFF pin. When the DLL is turned
off, the device behaves in DDR-I mode (with one cycle latency
and a longer access time). For information refer to the application
note
AN5062
‘DLL
Considerations
in
QDRII/DDRII/QDRII+/DDRII+’.
Application Example
Figure 1 shows four DDR-II SIO used in an application.
Figure 1. Application Example
SRAM 1
Vt
D
R
BUS
MASTER
(CPU
or
ASIC)
A
B
WB
S
LD
R/W W
LDR/W
## ## ##
DATA IN
DATA OUT
Address
LD#
R/W#
BWS#
ZQ
Q
CQ
CQ#
C C# K K#
SRAM 4
R = 250Ohms
B
W
LD R/W S
#
# #
D
A
R
ZQ
Q
CQ
CQ#
C C# K K#
R = 250Ohms
Vt
Vt
SRAM 1 Input CQ
SRAM 1 Input CQ#
SRAM 4 Input CQ
SRAM 4 Input CQ#
Source K
Source K#
Delayed K
Delayed K#
R
Document #: 001-44698 Rev. *A
R = 50Ohms
Vt = VREF
Page 9 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Truth Table
The truth table for CY7C1392JV18, CY7C1992JV18, CY7C1393JV18, and CY7C1394JV18 follows. [2, 3, 4, 5, 6, 7]
Operation
K
LD
R/W
Write Cycle:
Load address; wait one cycle;
input write data on consecutive K and K rising edges.
L-H
L
L
D(A + 0) at K(t + 1)↑ D(A + 1) at K(t + 1)↑
Read Cycle:
Load address; wait one and a half cycle;
read data on consecutive C and C rising edges.
L-H
L
H
Q(A + 0) at C(t + 1)↑ Q(A + 1) at C(t + 2)↑
NOP: No Operation
L-H
H
X
High-Z
High-Z
Stopped
X
X
Previous State
Previous State
Standby: Clock Stopped
DQ
DQ
Write Cycle Descriptions
The write cycle description table for CY7C1392JV18 and CY7C1393JV18 follows. [2, 8]
BWS0/ BWS1/
K
K
L
L–H
–
L
L
–
L
H
L–H
L
H
–
H
L
L–H
H
L
–
H
H
L–H
H
H
–
NWS0
NWS1
L
Comments
During the data portion of a write sequence:
CY7C1392JV18 − both nibbles (D[7:0]) are written into the device.
CY7C1393JV18 − both bytes (D[17:0]) are written into the device.
L-H During the data portion of a write sequence:
CY7C1392JV18 − both nibbles (D[7:0]) are written into the device.
CY7C1393JV18 − both bytes (D[17:0]) are written into the device.
–
During the data portion of a write sequence:
CY7C1392JV18 − only the lower nibble (D[3:0]) is written into the device, D[7:4] remains unaltered.
CY7C1393JV18 − only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
L–H During the data portion of a write sequence:
CY7C1392JV18 − only the lower nibble (D[3:0]) is written into the device, D[7:4] remains unaltered.
CY7C1393JV18 − only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
–
During the data portion of a write sequence:
CY7C1392JV18 − only the upper nibble (D[7:4]) is written into the device, D[3:0] remains unaltered.
CY7C1393JV18 − only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
L–H During the data portion of a write sequence:
CY7C1392JV18 − only the upper nibble (D[7:4]) is written into the device, D[3:0] remains unaltered.
CY7C1393JV18 − only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
–
No data is written into the devices during this portion of a write operation.
L–H No data is written into the devices during this portion of a write operation.
Notes
2. X = “Don't Care,” H = Logic HIGH, L = Logic LOW, ↑represents rising edge.
3. Device powers up deselected with the outputs in a tri-state condition.
4. “A” represents address location latched by the devices when transaction was initiated. A + 0, A + 1 represents the internal address sequence in the burst.
5. “t” represents the cycle at which a Read/Write operation is started. t + 1, and t + 2 are the first, and second clock cycles respectively succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
7. It is recommended that K = K and C = C = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging
symmetrically.
8. Is based on a write cycle that was initiated in accordance with the Write Cycle Descriptions table. NWS0, NWS1, BWS0, BWS1, BWS2 and BWS3 can be altered on
different portions of a write cycle, as long as the setup and hold requirements are achieved.
Document #: 001-44698 Rev. *A
Page 10 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Write Cycle Descriptions
The write cycle description table for CY7C1992JV18 follows. [2, 8]
BWS0
K
K
L
L–H
–
L
–
H
L–H
H
–
Comments
During the data portion of a write sequence, the single byte (D[8:0]) is written into the device.
L–H During the data portion of a write sequence, the single byte (D[8:0]) is written into the device.
–
No data is written into the device during this portion of a write operation.
L–H No data is written into the device during this portion of a write operation.
Write Cycle Descriptions
The write cycle description table for CY7C1394JV18 follows. [2, 8]
BWS0
BWS1
BWS2
BWS3
K
K
Comments
L
L
L
L
L–H
–
During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
L
L
L
L
–
L
H
H
H
L–H
L
H
H
H
–
H
L
H
H
L–H
H
L
H
H
–
H
H
L
H
L–H
H
H
L
H
–
H
H
H
L
L–H
H
H
H
L
–
H
H
H
H
L–H
H
H
H
H
–
Document #: 001-44698 Rev. *A
L–H During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
–
During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
L–H During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
–
During the data portion of a write sequence, only the byte (D[17:9]) is written into
the device. D[8:0] and D[35:18] remains unaltered.
L–H During the data portion of a write sequence, only the byte (D[17:9]) is written into
the device. D[8:0] and D[35:18] remains unaltered.
–
During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
L–H During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
–
During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
L–H During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
–
No data is written into the device during this portion of a write operation.
L–H No data is written into the device during this portion of a write operation.
Page 11 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
IEEE 1149.1 Serial Boundary Scan (JTAG)
These SRAMs incorporate a serial boundary scan Test Access
Port (TAP) in the FBGA package. This part is fully compliant with
IEEE Standard 1149.1-2001. The TAP operates using JEDEC
standard 1.8V IO logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, tie TCK LOW (VSS) to
prevent clocking of the device. TDI and TMS are internally pulled
up and may be unconnected. They may alternatively be
connected to VDD through a pull up resistor. Leave TDO
unconnected. Upon power up, the device comes up in a reset
state, which does not interfere with the operation of the device.
Test Access Port—Test Clock
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. Leave this pin
unconnected if the TAP is not used. The pin is pulled up
internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI pin is used to serially input information into the registers
and is connected to the input of any of the registers. The register
between TDI and TDO is chosen by the instruction that is loaded
into the TAP instruction register. For information on loading the
instruction register, see the TAP Controller State Diagram on
page 14. TDI is internally pulled up and is unconnected if the TAP
is unused in an application. TDI is connected to the most significant bit (MSB) on any register.
Instruction Register
Three-bit instructions are serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO pins, as shown in TAP Controller Block Diagram on
page 15. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state, as described
in the previous section.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binar ‘01’ pattern to enable the
fault isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between TDI
and TDO pins. This enables shifting of data through the SRAM
with minimal delay. The bypass register is set LOW (VSS) when
the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several No Connect (NC) pins are also
included in the scan register to reserve pins for higher density
devices.
The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and TDO
pins when the controller is moved to the Shift-DR state. The
EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions are
used to capture the contents of the input and output ring.
The Boundary Scan Order on page 18 shows the order in which
the bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected to
TDI, and the LSB is connected to TDO.
Test Data-Out (TDO)
Identification (ID) Register
The TDO output pin is used to serially clock data out from the
registers. The output is active, depending upon the current state
of the TAP state machine (see Instruction Codes on page 17).
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSB) of any register.
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and is shifted out when the TAP controller is in the
Shift-DR state. The ID register has a vendor code and other information described in Identification Register Definitions on page
17.
Performing a TAP Reset
A reset is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This reset does not affect the operation of the
SRAM and is performed while the SRAM is operating. At power
up, the TAP is reset internally to ensure that TDO comes up in a
High-Z state.
TAP Registers
Registers are connected between the TDI and TDO pins to scan
the data in and out of the SRAM test circuitry. Only one register
can be selected at a time through the instruction registers. Data
is serially loaded into the TDI pin on the rising edge of TCK. Data
is output on the TDO pin on the falling edge of TCK.
Document #: 001-44698 Rev. *A
TAP Instruction Set
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in Instruction
Codes on page 17. Do not use three of these instructions that
are listed as RESERVED. The other five instructions are
described in this section in detail.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO pins. To execute
the instruction after it is shifted in, move the TAP controller into
the Update-IR state.
Page 12 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
IDCODE
BYPASS
The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO pins and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state. The
IDCODE instruction is loaded into the instruction register at
power up or whenever the TAP controller is supplied a
Test-Logic-Reset state.
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. The SAMPLE Z command puts the output bus
into a High-Z state until the next command is supplied during the
Update IR state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the input and output pins is captured
in the boundary scan register.
The TAP controller clock only operates at a frequency up to 20
MHz, while the SRAM clock operates more than an order of
magnitude faster. Because there is a large difference in the clock
frequencies, it is possible that during the Capture-DR state, an
input or output undergoes a transition. The TAP then tries to
capture a signal while in transition (metastable state). This does
not harm the device, but there is no guarantee as to the value
that is captured. Repeatable results may not be possible.
To guarantee that the boundary scan register captures the
correct value of a signal, stabilize the SRAM signal long enough
to meet the TAP controller's capture setup plus hold times (tCS
and tCH). The SRAM clock input might not be captured correctly
if there is no way in a design to stop (or slow) the clock during a
SAMPLE/PRELOAD instruction. If this is an issue, it is still
possible to capture all other signals and simply ignore the value
of the CK and CK captured in the boundary scan register.
EXTEST
The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the Shift-DR controller state.
EXTEST OUTPUT BUS TRI-STATE
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tri-state mode.
The boundary scan register has a special bit located at bit 47.
When this scan cell, called the ‘extest output bus tri-state’, is
latched into the preload register during the Update-DR state in
the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it enables the output buffers to drive the
output bus. When LOW, this bit places the output bus into a
High-Z condition.
This bit is set by entering the SAMPLE/PRELOAD or EXTEST
command, and then shifting the desired bit into that cell, during
the Shift-DR state. During Update-DR, the value loaded into that
shift-register cell latches into the preload register. When the
EXTEST instruction is entered, this bit directly controls the output
Q-bus pins. Note that this bit is pre-set LOW to enable the output
when the device is powered up, and also when the TAP controller
is in the Test-Logic-Reset state.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells before the selection
of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases
occurs concurrently when required, that is, while the data
captured is shifted out, the preloaded data is shifted in.
Document #: 001-44698 Rev. *A
Page 13 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
TAP Controller State Diagram
The state diagram for the TAP controller follows. [9]
1
TEST-LOGIC
RESET
0
0
TEST-LOGIC/
IDLE
1
SELECT
DR-SCAN
1
1
SELECT
IR-SCAN
0
0
1
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
1
1
EXIT1-DR
1
EXIT1-IR
0
0
PAUSE-IR
1
0
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-IR
UPDATE-DR
1
1
0
PAUSE-DR
0
0
0
1
0
Note
9. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
Document #: 001-44698 Rev. *A
Page 14 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
TAP Controller Block Diagram
0
Bypass Register
2
Selection
Circuitry
TDI
1
0
Selection
Circuitry
Instruction Register
31
30
29
.
.
2
1
0
1
0
TDO
Identification Register
106
.
.
.
.
2
Boundary Scan Register
TCK
TAP Controller
TMS
TAP Electrical Characteristics
Over the Operating Range [10, 11, 12]
Parameter
Description
Test Conditions
Min
Max
Unit
VOH1
Output HIGH Voltage
IOH = −2.0 mA
1.4
V
VOH2
Output HIGH Voltage
IOH = −100 μA
1.6
V
VOL1
Output LOW Voltage
IOL = 2.0 mA
0.4
V
VOL2
Output LOW Voltage
IOL = 100 μA
0.2
V
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
IX
Input and Output Load Current
0.65VDD VDD + 0.3
GND ≤ VI ≤ VDD
V
–0.3
0.35VDD
V
–5
5
μA
Notes
10. These characteristics pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics table.
11. Overshoot: VIH(AC) < VDDQ + 0.85V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > −1.5V (Pulse width less than tCYC/2).
12. All Voltage referenced to Ground.
Document #: 001-44698 Rev. *A
Page 15 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
TAP AC Switching Characteristics
Over the Operating Range [13, 14]
Parameter
Description
Min
Max
Unit
20
MHz
tTCYC
TCK Clock Cycle Time
tTF
TCK Clock Frequency
tTH
TCK Clock HIGH
20
ns
tTL
TCK Clock LOW
20
ns
tTMSS
TMS Setup to TCK Clock Rise
5
ns
tTDIS
TDI Setup to TCK Clock Rise
5
ns
tCS
Capture Setup to TCK Rise
5
ns
tTMSH
TMS Hold after TCK Clock Rise
5
ns
tTDIH
TDI Hold after Clock Rise
5
ns
tCH
Capture Hold after Clock Rise
5
ns
50
ns
Setup Times
Hold Times
Output Times
tTDOV
TCK Clock LOW to TDO Valid
tTDOX
TCK Clock LOW to TDO Invalid
10
0
ns
ns
TAP Timing and Test Conditions
Figure 2 shows the TAP timing and test conditions. [14]
Figure 2. TAP Timing and Test Conditions
0.9V
ALL INPUT PULSES
1.8V
50Ω
0.9V
TDO
0V
Z0 = 50Ω
(a)
CL = 20 pF
tTH
GND
tTL
Test Clock
TCK
tTCYC
tTMSH
tTMSS
Test Mode Select
TMS
tTDIS
tTDIH
Test Data In
TDI
Test Data Out
TDO
tTDOV
tTDOX
Notes
13. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
14. Test conditions are specified using the load in TAP AC Test Conditions. tR/tF = 1 ns.
Document #: 001-44698 Rev. *A
Page 16 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Identification Register Definitions
Instruction Field
Value
CY7C1392JV18
CY7C1992JV18
CY7C1393JV18
CY7C1394JV18
000
000
000
000
Revision Number
(31:29)
Cypress Device ID
(28:12)
Cypress JEDEC ID
(11:1)
Description
Version number.
11010100010000101 11010100010001101 11010100010010101 11010100010100101 Defines the type of
SRAM.
00000110100
00000110100
00000110100
00000110100
1
1
1
1
ID Register
Presence (0)
Allows unique
identification of
SRAM vendor.
Indicates the
presence of an ID
register.
Scan Register Sizes
Register Name
Bit Size
Instruction
3
Bypass
1
ID
32
Boundary Scan
107
Instruction Codes
Instruction
Code
Description
EXTEST
000
Captures the input and output ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO. This
operation does not affect SRAM operation.
SAMPLE Z
010
Captures the input and output contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOA
D
100
Captures the input and output ring contents. Places the boundary scan register between TDI and
TDO. Does not affect the SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM operation.
Document #: 001-44698 Rev. *A
Page 17 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Boundary Scan Order
Bit #
Bump ID
Bit #
Bump ID
Bit #
Bump ID
Bit #
Bump ID
0
6R
28
10G
56
6A
84
2J
1
6P
29
9G
57
5B
85
3K
2
6N
30
11F
58
5A
86
3J
3
7P
31
11G
59
4A
87
2K
4
7N
32
9F
60
5C
88
1K
5
7R
33
10F
61
4B
89
2L
6
8R
34
11E
62
3A
90
3L
7
8P
35
10E
63
1H
91
1M
8
9R
36
10D
64
1A
92
1L
9
11P
37
9E
65
2B
93
3N
10
10P
38
10C
66
3B
94
3M
11
10N
39
11D
67
1C
95
1N
12
9P
40
9C
68
1B
96
2M
13
10M
41
9D
69
3D
97
3P
14
11N
42
11B
70
3C
98
2N
15
9M
43
11C
71
1D
99
2P
16
9N
44
9B
72
2C
100
1P
17
11L
45
10B
73
3E
101
3R
18
11M
46
11A
74
2D
102
4R
19
9L
47
Internal
75
2E
103
4P
20
10L
48
9A
76
1E
104
5P
21
11K
49
8B
77
2F
105
5N
22
10K
50
7C
78
3F
106
5R
23
9J
51
6C
79
1G
24
9K
52
8A
80
1F
25
10J
53
7A
81
3G
26
11J
54
7B
82
2G
27
11H
55
6B
83
1J
Document #: 001-44698 Rev. *A
Page 18 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Power Up Sequence in DDR-II SRAM
DLL Constraints
Power up and initialize DDR-II SRAMs in a predefined manner
to prevent undefined operations.
■
DLL uses K clock as its synchronizing input. The input has low
phase jitter, which is specified as tKC Var.
■
The DLL functions at frequencies down to 120 MHz.
■
If the input clock is unstable and the DLL is enabled, then the
DLL may lock onto an incorrect frequency, causing unstable
SRAM behavior. To avoid this, provide1024 cycles stable clock
to relock to the desired clock frequency.
Power Up Sequence
■
Apply power and drive DOFF either HIGH or LOW (All other
inputs are HIGH or LOW).
❐ Apply VDD before VDDQ.
❐ Apply VDDQ before VREF or at the same time as VREF.
❐ Drive DOFF HIGH.
■
Provide stable DOFF (HIGH), power and clock (K, K) for 1024
cycles to lock the DLL.
~
~
Figure 3. Power Up Waveforms
K
K
~
~
Unstable Clock
> 1024 Stable clock
Start Normal
Operation
Clock Start (Clock Starts after V DD / V DDQ Stable)
VDD / VDDQ
DOFF
Document #: 001-44698 Rev. *A
V DD / V DDQ Stable (< +/- 0.1V DC per 50ns )
Fix High (or tie to VDDQ)
Page 19 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Maximum Ratings
Current into Outputs (LOW) ........................................ 20 mA
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with Power Applied.. –55°C to +125°C
Supply Voltage on VDD Relative to GND ........–0.5V to +2.9V
Static Discharge Voltage (MIL-STD-883, M. 3015).. > 2001V
Latch-up Current ................................................... > 200 mA
Operating Range
Range
Supply Voltage on VDDQ Relative to GND.......–0.5V to +VDD
Commercial
DC Applied to Outputs in High-Z ........ –0.5V to VDDQ + 0.3V
Industrial
DC Input Voltage
[11]
Ambient
Temperature (TA)
VDD [15]
VDDQ [15]
0°C to +70°C
1.8 ± 0.1V
1.4V to
VDD
–40°C to +85°C
.............................. –0.5V to VDD + 0.3V
Electrical Characteristics
DC Electrical Characteristics
Over the Operating Range [12]
Parameter
VDD
VDDQ
VOH
VOL
VOH(LOW)
VOL(LOW)
VIH
VIL
IX
IOZ
VREF
IDD [19]
Description
Power Supply Voltage
IO Supply Voltage
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current
Output Leakage Current
Input Reference Voltage [18]
VDD Operating Supply
Test Conditions
Note 16
Note 17
IOH = −0.1 mA, Nominal Impedance
IOL = 0.1 mA, Nominal Impedance
GND ≤ VI ≤ VDDQ
GND ≤ VI ≤ VDDQ, Output Disabled
Typical Value = 0.75V
VDD = Max,
300 MHz
IOUT = 0 mA,
f = fMAX = 1/tCYC
250 MHz
ISB1
Automatic Power down
Current
Max VDD,
Both Ports Deselected,
VIN ≥ VIH or VIN ≤ VIL
f = fMAX = 1/tCYC,
Inputs Static
300 MHz
250 MHz
(x8)
(x9)
(x18)
(x36)
(x8)
(x9)
(x18)
(x36)
(x8)
(x9)
(x18)
(x36)
(x8)
Min
Typ
Max
Unit
1.7
1.8
1.9
V
1.4
1.5
VDD
V
VDDQ/2 – 0.12
VDDQ/2 + 0.12 V
VDDQ/2 – 0.12
VDDQ/2 + 0.12 V
VDDQ – 0.2
VDDQ
V
VSS
0.2
V
VREF + 0.1
VDDQ + 0.3
V
–0.3
VREF – 0.1
V
−5
5
μA
−5
5
μA
0.68
0.75
0.95
V
820
mA
825
865
935
700
mA
700
725
770
275
mA
275
285
300
255
mA
(x9)
(x18)
(x36)
255
260
275
Notes
15. Power up: assumes a linear ramp from 0V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
16. Outputs are impedance controlled. IOH = –(VDDQ/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.
17. Outputs are impedance controlled. IOL = (VDDQ/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.
18. VREF(min) = 0.68V or 0.46VDDQ, whichever is larger, VREF(max) = 0.95V or 0.54VDDQ, whichever is smaller.
19. The operation current is calculated with 50% read cycle and 50% write cycle.
Document #: 001-44698 Rev. *A
Page 20 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
AC Electrical Characteristics
Over the Operating Range [11]
Parameter
Description
Test Conditions
Min
Typ
Max
Unit
VIH
Input HIGH Voltage
VREF + 0.2
–
–
V
VIL
Input LOW Voltage
–
–
VREF – 0.2
V
Capacitance
Tested initially and after any design or process change that may affect these parameters.
Parameter
Description
Max
Unit
5
pF
Clock Input Capacitance
6
pF
Output Capacitance
7
pF
CIN
Input Capacitance
CCLK
CO
Test Conditions
TA = 25°C, f = 1 MHz, VDD = 1.8V, VDDQ = 1.5V
Thermal Resistance
Tested initially and after any design or process change that may affect these parameters.
Parameter
Description
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
Test Conditions
165 FBGA Package Unit
Test conditions follow standard test methods and
procedures for measuring thermal impedance, in
accordance with EIA/JESD51.
18.7
°C/W
4.5
°C/W
Figure 4. AC Test Loads and Waveforms
VREF = 0.75V
VREF
0.75V
VREF
OUTPUT
Z0 = 50Ω
Device
Under
Test
ZQ
RL = 50Ω
VREF = 0.75V
R = 50Ω
ALL INPUT PULSES
1.25V
0.75V
OUTPUT
Device
Under
Test ZQ
RQ =
250Ω
(a)
0.75V
INCLUDING
JIG AND
SCOPE
5 pF
[20]
0.25V
Slew Rate = 2 V/ns
RQ =
250Ω
(b)
Note
20. Unless otherwise noted, test conditions are based on signal transition time of 2V/ns, timing reference levels of 0.75V, Vref = 0.75V, RQ = 250Ω, VDDQ = 1.5V, input
pulse levels of 0.25V to 1.25V, and output loading of the specified IOL/IOH and load capacitance shown in (a) of AC Test Loads and Waveforms.
Document #: 001-44698 Rev. *A
Page 21 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Switching Characteristics
Over the Operating Range [20, 21]
Cypress Consortium
Parameter Parameter
300 MHz
Description
Min Max Min Max
VDD(Typical) to the First Access [22]
tPOWER
250 MHz
1
1
Unit
ms
tCYC
tKHKH
K Clock and C Clock Cycle Time
3.3
8.4
4.0
8.4
ns
tKH
tKHKL
Input Clock (K/K; C/C) HIGH
1.32
–
1.6
–
ns
tKL
tKLKH
Input Clock (K/K; C/C) LOW
1.32
–
1.6
–
ns
tKHKH
tKHKH
K Clock Rise to K Clock Rise and C to C Rise (rising edge to rising edge) 1.49
–
1.8
–
ns
tKHCH
tKHCH
K/K Clock Rise to C/C Clock Rise (rising edge to rising edge)
0
1.45
0
1.8
ns
Setup Times
tSA
tAVKH
Address Setup to K Clock Rise
0.4
–
0.5
–
ns
tSC
tIVKH
Control Setup to K Clock Rise (LD, R/W)
0.4
–
0.5
–
ns
tSCDDR
tIVKH
Double Data Rate Control Setup to Clock (K/K) Rise (BWS0, BWS1, BWS2, 0.3
BWS3)
–
0.35
–
ns
tSD
tDVKH
D[X:0] Setup to Clock (K/K) Rise
0.3
–
0.35
–
ns
Hold Times
tHA
tKHAX
Address Hold after K Clock Rise
0.4
–
0.5
–
ns
tHC
tKHIX
Control Hold after K Clock Rise (LD, R/W)
0.4
–
0.5
–
ns
tHCDDR
tKHIX
Double Data Rate Control Hold after Clock (K/K) Rise (BWS0, BWS1,
BWS2, BWS3)
0.3
–
0.35
–
ns
tHD
tKHDX
D[X:0] Hold after Clock (K/K) Rise
0.3
–
0.35
–
ns
–
0.45
–
0.45
ns
–0.45
–
–0.45
–
ns
–
0.45
–
0.45
ns
–0.45
–
–0.45
–
ns
Output Times
tCO
tCHQV
C/C Clock Rise (or K/K in single clock mode) to Data Valid
Data Output Hold after Output C/C Clock Rise (Active to Active)
tDOH
tCHQX
tCCQO
tCHCQV
C/C Clock Rise to Echo Clock Valid
tCQOH
tCHCQX
Echo Clock Hold after C/C Clock Rise
tCQD
tCQHQV
Echo Clock High to Data Valid
tCQDOH
tCQHQX
Echo Clock High to Data Invalid
tCQH
tCQHCQH
tCHZ
tCLZ
tCQHCQL
tCQHCQH
tCHQZ
tCHQX1
Output Clock (CQ/CQ) HIGH
0.27
[23]
CQ Clock Rise to CQ Clock Rise (rising edge to rising edge)
Clock (C/C) Rise to High-Z (Active to High-Z)
Clock (C/C) Rise to Low-Z
[24, 25]
[24, 25]
[23]
0.30
ns
–0.27
–
–0.30
–
ns
1.24
–
1.55
–
ns
1.24
–
1.55
–
ns
–
0.45
–
0.45
ns
–0.45
–
–0.45
–
ns
–
0.20
–
0.20
ns
–
1024
–
Cycles
DLL Timing
tKC Var
tKC Var
Clock Phase Jitter
tKC lock
tKC lock
DLL Lock Time (K, C)
1024
tKC Reset
tKC Reset
K Static to DLL Reset
30
30
ns
Notes
21. When a part with a maximum frequency above 250 MHz is operating at a lower clock frequency, it requires the input timing of the frequency range in which it is being
operated and outputs data with the output timings of that frequency range.
22. This part has a voltage regulator internally; tPOWER is the time that the power must be supplied above VDD minimum initially before a read or write operation can be
initiated.
23. These parameters are extrapolated from the input timing parameters (tKHKH - 250 ps, where 250 ps is the internal jitter. An input jitter of 200 ps (tKC Var) is already
included in the tKHKH). These parameters are only guaranteed by design and are not tested in production
24. tCHZ, tCLZ, are specified with a load capacitance of 5 pF as in (b) of AC Test Loads and Waveforms on page 21. Transition is measured ± 100 mV from steady-state voltage.
25. At any voltage and temperature tCHZ is less than tCLZ and tCHZ less than tCO.
Document #: 001-44698 Rev. *A
Page 22 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Switching Waveforms
Figure 5. Read/Write/Deselect Sequence [26, 27, 28]
NOP
READ
(burst of 2)
2
1
READ
(burst of 2)
3
WRITE
(burst of 2)
5
WRITE
(burst of 2)
4
READ
(burst of 2)
6
NOP
7
8
K
tKH
tCYC
tKL
tKHKH
K
LD
t SC
tHC
R/W
A
A0
tSA
A1
A2
A3
A4
tHD
tHD
tHA
tSD
tSD
D
D20
Q00
Q
t KHCH
t
Q01
tCQD
t CLZ
Q10
D21
D31
Q11
Q40
Q41
tDOH
KHCH
tCO
D30
t CHZ
tCQDOH
C
tKH
tCYC
tKL
tKHKH
C#
tCQOH
tCCQO
CQ
tCQOH
tCCQO
tCQH
tCQHCQH
CQ#
DON’T CARE
UNDEFINED
Notes
26. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, that is, A0+1.
27. Outputs are disabled (High-Z) one clock cycle after a NOP.
28. In this example, if address A4 = A3, then data Q40 = D30 and Q41 = D31. Write data is forwarded immediately as read results. This note applies to the whole diagram.
Document #: 001-44698 Rev. *A
Page 23 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered.
Speed
(MHz)
300
Ordering Code
CY7C1392JV18-300BZC
Package
Diagram
Package Type
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
Operating
Range
Commercial
CY7C1992JV18-300BZC
CY7C1393JV18-300BZC
CY7C1394JV18-300BZC
CY7C1392JV18-300BZXC
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1992JV18-300BZXC
CY7C1393JV18-300BZXC
CY7C1394JV18-300BZXC
CY7C1392JV18-300BZI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
Industrial
CY7C1992JV18-300BZI
CY7C1393JV18-300BZI
CY7C1394JV18-300BZI
CY7C1392JV18-300BZXI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1992JV18-300BZXI
CY7C1393JV18-300BZXI
CY7C1394JV18-300BZXI
250
CY7C1392JV18-250BZC
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
Commercial
CY7C1992JV18-250BZC
CY7C1393JV18-250BZC
CY7C1394JV18-250BZC
CY7C1392JV18-250BZXC
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1992JV18-250BZXC
CY7C1393JV18-250BZXC
CY7C1394JV18-250BZXC
CY7C1392JV18-250BZI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
Industrial
CY7C1992JV18-250BZI
CY7C1393JV18-250BZI
CY7C1394JV18-250BZI
CY7C1392JV18-250BZXI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
CY7C1992JV18-250BZXI
CY7C1393JV18-250BZXI
CY7C1394JV18-250BZXI
Document #: 001-44698 Rev. *A
Page 24 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Package Diagram
Figure 6. 165-Ball FBGA (13 x 15 x 1.4 mm)
BOTTOM VIEW
PIN 1 CORNER
TOP VIEW
Ø0.05 M C
Ø0.25 M C A B
PIN 1 CORNER
Ø0.50 -0.06
(165X)
+0.14
1
2
3
4
5
6
7
8
9
10
11
11
9
8
7
6
5
4
3
2
1
A
B
B
C
C
1.00
A
D
D
E
F
F
G
G
H
J
14.00
E
15.00±0.10
15.00±0.10
10
H
J
K
L
L
7.00
K
M
M
N
N
P
P
R
R
A
A
1.00
5.00
10.00
B
B
13.00±0.10
13.00±0.10
1.40 MAX.
0.15 C
0.53±0.05
0.25 C
0.15(4X)
NOTES :
SOLDER PAD TYPE : NON-SOLDER MASK DEFINED (NSMD)
PACKAGE WEIGHT : 0.475g
JEDEC REFERENCE : MO-216 / DESIGN 4.6C
PACKAGE CODE : BB0AC
0.35±0.06
0.36
SEATING PLANE
C
Document #: 001-44698 Rev. *A
51-85180 *A
Page 25 of 26
[+] Feedback
CY7C1392JV18, CY7C1992JV18
CY7C1393JV18, CY7C1394JV18
Document History Page
Document Title: CY7C1392JV18/CY7C1992JV18/CY7C1393JV18/CY7C1394JV18, 18-Mbit DDR-II SIO SRAM 2-Word Burst
Architecture
Document Number: 001-44698
REV.
ECN NO.
ORIG. OF
CHANGE
SUBMISSION
DATE
DESCRIPTION OF CHANGE
**
2192568 VKN/PYRS
See ECN
New data sheet
*A
2561974 VKN/PYRS
09/04/08
Converted from preliminary to final,
Added 250 MHz speed bin,
Changed JTAG ID [31:29] from 001 to 000,
Updated power up sequence waveform and its description,
Changed Ambient Temperature with Power Applied from “–10°C to +85°C” to
“–55°C to +125°C” in the “Maximum Ratings “ on page 20,
Changed ΘJA and ΘJC from 28.51 and 5.91 °C/W to 18.7 and 4.5 °C/W respectively.
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
Clocks & Buffers
PSoC Solutions
psoc.cypress.com
clocks.cypress.com
General
Low Power/Low Voltage
psoc.cypress.com/solutions
psoc.cypress.com/low-power
Wireless
wireless.cypress.com
Precision Analog
Memories
memory.cypress.com
LCD Drive
psoc.cypress.com/lcd-drive
image.cypress.com
CAN 2.0b
psoc.cypress.com/can
USB
psoc.cypress.com/usb
Image Sensors
psoc.cypress.com/precision-analog
© Cypress Semiconductor Corporation, 2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any
circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 001-44698 Rev. *A
Revised August 22, 2008
Page 26 of 26
QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, IDT, NEC, Renesas, and Samsung. All product and company names mentioned in this document
are the trademarks of their respective holders.
[+] Feedback