CYP15G0402DXB CYV15G0402DXB Quad HOTLink II™ SERDES Features • Second-generation HOTLink® technology • Compliant to multiple standards — Fibre Channel, Gigabit Ethernet (IEEE802.3z), ESCON® and DVB-ASI • • • • • • • • • • • — CYV15G0402DXB compliant to SMPTE 259M and SMPTE 292M Quad-channel transceiver operates from 195 to 1500 Mbps serial data rate — Aggregate throughput of 12 Gbps 10-bit unencoded data transport Selectable parity check/generate Four independent 10-bit channels with separate Clock and Data Recovery for each channel Selectable input clocking options MultiFrame™ Receive Framer — Comma or full K28.5 detect — Circuit board traces • JTAG boundary scan • Built-In Self-Test (BIST) for at-speed link testing • Per-channel Link Quality Indicator — Analog signal detect • • • • • — Digital signal detect Low-power 2.5W @3.3V typical Single 3.3V supply 256-ball thermally enhanced BGA Pb-Free package option available 0.25µ BiCMOS technology Functional Description — Single or Multi-Byte framer for byte alignment The CYP(V)15G0402DXB[1] Quad HOTLink II™ SERDES is a point-to-point communications building block allowing the transfer of preencoded data over high-speed serial links (optical fiber, balanced, and unbalanced copper transmission lines) at signaling speeds ranging from 195 to 1500 MBaud per serial link. — Low-latency option Synchronous LVTTL parallel interface Internal phase-locked loops (PLLs) with no external PLL components Optional Phase Align Buffer in Transmit Path Differential PECL-compatible serial inputs Differential PECL-compatible serial outputs — Source matched for 50Ω transmission lines Each transmit channel accepts preencoded 10-bit transmission characters in an Input Register, serializes each character, and drives it out a PECL-compatible differential line driver. Each receive channel accepts a serial data stream at a differential line receiver, deserializes the stream into 10-bit characters, optionally frames these characters to the proper 10-bit character boundaries and presents these characters to an Output register. Figure 1 illustrates typical connections between independent systems and a CYP(V)15G0402DXB. — No external resistors required The CYV15G0402DXB satisfies the SMPTE-259M and SMPTE-292M compliance as per the EG34-1999 Pathological Test Requirements. — Signaling rate controlled edge rates • Compatible with — Fiber-optic modules — Copper cables 10 Serial Links Independent Channel Transceiver 10 10 CYP(V)15G0402DXB 10 10 Serial Links Independent Channel Transceiver 10 10 Serial Links Independent Channel Transceiver 10 Cable or Optical Connections 10 10 10 10 System Host With Encoder/Decoder System Host With Encoder/Decoder Independent Channel Transceiver 10 10 10 Serial Links 10 Figure 1. CYP(V)15G0402DXB HOTLink II™ System Connections Note: 1. CYV15G0402DXB refers to SMPTE 259M and SMPTE 292M compliant devices. CYP15G0402DXB refers to devices that are not compliant to SMPTE 259M and SMPTE 292M pathological test requirements. CYP(V)15G0402DXB refers to both devices. Cypress Semiconductor Corporation Document #: 38-02057 Rev. *G • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised March 31, 2005 CYP15G0402DXB CYV15G0402DXB As a second-generation HOTLink device, the CYP(V)15G0402DXB extends the HOTLink family to faster data rates, while maintaining serial link compatibility (data, command and BIST) with other HOTLink devices.The transmit (TX) section of the CYP(V)15G0402DXB Quad HOTLink II SERDES consists of four ten bit wide channels that accept a preencoded character on every clock cycle. Transmission characters are passed from the Transmit Input Register to a Serializer. The serialized characters are output from a differential transmission line driver at a bit-rate of 10 or 20 times the input reference clock. The receive (RX) section of the CYP(V)15G0402DXB Quad HOTLink II SERDES consists of four ten bit wide channels. Each channel accepts a serial bit-stream from a PECL-compatible differential line receiver and, using a completely integrated PLL Clock Synchronizer, recovers the timing information necessary for data reconstruction. Each recovered bit-stream is deserialized and framed into characters. Recovered characters are then passed to the receiver output register, along with a recovered character clock. The parallel input interface may be configured for numerous forms of clocking to provide the high flexibility in system architecture. Each transmit and receive channel contains an independent BIST pattern generator and checker. This BIST hardware allows at-speed testing of the interface data path. HOTLink II devices are ideal for a variety of applications where parallel interfaces can be replaced with high-speed, point-to-point serial links. Some applications include interconnecting backplanes on switches, routers, servers and video transmission systems. The CYV15G0402DXB is verified by testing to be compliant to all the pathological test patterns documented in SMPTE EG34-1999, for both the SMPTE 259M and 292M signaling rates. The tests ensure that the receiver recovers data with no errors for the following patterns: 1. Repetitions of 20 ones and 20 zeros. 2. Single burst of 44 ones or 44 zeros. 3. Repetitions of 19 ones followed by 1 zero or 19 zeros followed by 1 one. Framer Phase Align Buffer Framer Phase Align Buffer x10 x10 x10 x10 Framer Phase Align Buffer Framer Deserializer Serializer Deserializer Phase Align Buffer Serializer Deserializer TX RX TX RX TX RX TX INA± OUTB± INB± OUTC± INC± OUTD± Serializer Deserializer OUTA± Serializer RXDD[9:0] x10 Document #: 38-02057 Rev. *G RX IND± RXDB[9:0] x10 TXDD[9:0] TXDB[9:0] x10 RXDC[9:0] RXDA[9:0] x10 TXDC[9:0] TXDA[9:0] CYP(V)15G0402DXB Transceiver Logic Block Diagram Page 2 of 29 CYP15G0402DXB CYV15G0402DXB = Internal Signal Transmit Path Block Diagram REFCLK+ REFCLK– Transmit PLL Clock Multiplier TXRATE Bit-Rate Clock BISTLE SPDSEL Character-Rate Clock TXCLKO+ TXCLKO– BOE[7..0] RBIST[A..D] BIST Enable Latch Output Enable Latch 4 TXCKSEL TXPERA OELE 10 OUTA+ OUTA– Shifter 11 BIST LFSR 11 Parity Check TXOPA 11 Phase-Align Buffer TXDA[0..9] Input Register 8 TXLBA H M L TXCLKA 10 Shifter 11 BIST LFSR 11 Parity Check TXOPB 11 Phase-Align Buffer TXDB[0..9] Input Register TXPERB OUTB+ OUTB– H M L TXLBB TXCLKB 10 OUTC+ OUTC– Shifter 11 BIST LFSR 11 Parity Check TXOPC 11 Phase-Align Buffer TXDC[0..9] Input Register TXPERC TXLBC H M L TXCLKC 10 Shifter 11 BIST LFSR 11 Parity Check TXOPD 11 Phase-Align Buffer TXDD[0..9] Input Register TXPERD OUTD+ OUTD– H M L TXLBD TXCLKD TXRST PARCTL Document #: 38-02057 Rev. *G Parity Control Page 3 of 29 CYP15G0402DXB CYV15G0402DXB = Internal Signal Receive Path Block Diagram RXLE TRSTZ RX PLL Enable Latch BOE[7:0] Parity Control Character-Rate Clock SDASEL LPENA TMS TCLK TDI TDO JTAG Boundary Scan Controller Receive Signal Monitor BIST LFSR RFENA Output Register TXLBA Framer Clock and Data Recovery PLL Shifter INA+ INA– LFIA Receive Signal Monitor BIST LFSR RFENB Output Register TXLBB Framer Clock and Data Recovery PLL LFIB Shifter INB+ INB– Receive Signal Monitor BIST LFSR RFENC Output Register TXLBC Framer Clock and Data Recovery PLL Receive Signal Monitor TXLBD RBIST[A..D] RFEND FRAMCHAR RXRATE Output Register BIST LFSR Framer Clock and Data Recovery PLL RXOPC COMDETC LFID Shifter IND+ IND– RXDC[0..9] RXCLKC+ RXCLKC– ÷2 LPEND RXOPB COMDETB LFIC Shifter INC+ INC– RXDB[0..9] RXCLKB+ RXCLKB– ÷2 LPENC RXOPA COMDETA RXCLKA+ RXCLKA– ÷2 LPENB RXDA[0..9] ÷2 RXDD[0..9] RXOPD COMDETD RXCLKD+ RXCLKD– RFMODE Document #: 38-02057 Rev. *G Page 4 of 29 CYP15G0402DXB CYV15G0402DXB Pin Configuration (Top View)[2] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A INC- OUTC- N/C N/C VCC IND- OUTD- GND N/C N/C INA- OUTA- GND N/C N/C VCC INB- OUTB- N/C N/C B INC+ OUTC+ N/C N/C VCC IND+ OUTD+ GND N/C N/C INA+ OUTA+ GND N/C N/C VCC INB+ OUTB+ N/C N/C C TDI TMS PARCTL SDASEL GND BOE[7] BOE[5] BOE[3] BOE[1] GND GND GND VCC TXRATE RXRATE N/C TDO D TCLK GND BOE[6] BOE[4] BOE[2] BOE[0] GND GND GND VCC E VCC VCC VCC F TXPER C TXOP C TXDC [0] G LPENC LPENB VCC TRSTZ LPEND LPENA VCC N/C RXLE N/C N/C VCC VCC VCC VCC VCC N/C BISTLE RXDB [0] RXOP B RXDB [1] TXDC TXCKSEL TXDC [7] [4] TXDC [1] GND OELE FRAM CHAR RXDB [3] H GND GND GND GND GND GND GND GND J TXDC [9] TXDC [5] TXDC [2} TXDC [3] COMDET RXDB B [2] RXDB [7] RXDB [4] K RXDC [4] RXCLK C- TXDC [8] LFIC RXDB [5] RXDB [6] RXDB [9] RXCLKB + L RXDC [5] RXCLK C+ TXCLK C TXDC [6] RXDB [8] LFIB RXCLK B- TXDB [6] M RXDC [6] RXDC [7] RXDC [9] RXDC [8] TXDB [9] TXDB [8] TXDB [7] TXCLK B N GND GND GND GND GND GND GND GND P RXDC [3] RXDC [2] RXDC [1] RXDC [0] TXDB [5] TXDB [4] TXDB [3] TXDB [2] COMDET RXOP C C TXPER D TXOP D TXDB [1] TXDB [0] TXOP B TXPER B VCC VCC VCC VCC R RF MODE SPD SEL T VCC VCC VCC VCC U TXDD [0] TXDD [1] TXDD [2] TXDD [9] VCC RXDD [4] RXDD [3] GND V TXDD [3] TXDD [4] TXDD [8] RXDD [8] VCC RXDD [5] RXDD [1] W TXDD [5] TXDD [7] LFID RXCLK D– VCC RXDD [6] Y TXDD [6] TXCLK D RXDD [9] RXCLK D+ VCC RXDD [7] RXOP D RFEN C REFCLK - TXDA [1] GND TXDA [4] TXDA [8] VCC RXDA [4] RXOPA COMDET RXDA A [0] GND COMDET RFEN D D REFCLK + RFEN B GND TXDA [3] TXDA [7] VCC RXDA [9] RXDA [5] RXDA [2] RXDA [1] RXDD [0] GND TXCLKO TXRST – TXOPA RFEN A GND TXDA [2] TXDA [6] VCC LFIA RXCLKA – RXDA [6] RXDA [3] RXDD [2] GND TXCLKO + TXCLK A TXPER A GND TXDA [0] TXDA [5] VCC TXDA [9] RXCLKA + RXDA [8] RXDA [7] N/C Note: 2. N/C = Do Not Connect Document #: 38-02057 Rev. *G Page 5 of 29 CYP15G0402DXB CYV15G0402DXB Pin Configuration (Bottom View)[3] 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A N/C N/C OUTB- INB- VCC N/C N/C GND OUTA- INA- N/C N/C GND OUTD- IND- VCC N/C N/C OUTC- INC- B N/C N/C OUTB+ INB+ VCC N/C N/C GND OUTA+ INA+ N/C N/C GND OUTD+ IND+ VCC N/C N/C OUTC+ INC+ C TDO N/C RXRATE TXRATE VCC GND GND GND BOE[1] BOE[3] BOE[5] BOE[7] GND SDASEL PARCTL VCC LPENB LPENC TMS TDI D N/C N/C RXLE N/C VCC GND GND GND BOE[0] BOE[2] BOE[4] BOE[6] GND VCC LPENA LPEND TRSTZ TCLK E VCC VCC VCC VCC VCC VCC VCC VCC F RXDB [1] RXOP B RXDB [0] BISTLE N/C TXDC [0] TXOP C TXPER C G RXDB [3] FRAM CHAR OELE GND TXDC [1] TXDC [4] TXCK SEL TXDC [7] H GND GND GND GND GND GND GND GND J RXDB [4] RXDB [7] RXDB COMDET [2] B TXDC [3] TXDC [2} TXDC [5] TXDC [9] K RXCLKB + RXDB [9] RXDB [6] RXDB [5] LFIC TXDC [8] RXCLK C- RXDC [4] L TXDB [6] RXCLK B- LFIB RXDB [8] TXDC [6] TXCLK C RXCLK C+ RXDC [5] M TXCLK B TXDB [7] TXDB [8] TXDB [9] RXDC [8] RXDC [9] RXDC [7] RXDC [6] N GND GND GND GND GND GND GND GND P TXDB [2] TXDB [3] TXDB [4] TXDB [5] RXDC [0] RXDC [1] RXDC [2] RXDC [3] TXPERB TXOPB TXDB [0] TXDB [1] TXOP D TXPER D RXOP COMDET C C VCC VCC VCC VCC VCC VCC R SPD SEL RF MODE T VCC U RXDA COMDET RXOP [0] A A RXDA [4] VCC TXDA [8] TXDA [4] GND TXDA [1] REFCLK - RFEN C GND RXDD [3] RXDD [4] VCC TXDD [9] TXDD [2] TXDD [1] TXDD [0] V RXDA [1] RXDA [2] RXDA [5] RXDA [9] VCC TXDA [7] TXDA [3] GND RFEN B REFCLK + RFEN COMDET GND D D RXDD [1] RXDD [5] VCC RXDD [8] TXDD [8] TXDD [4] TXDD [3] W RXDA [3] RXDA [6] RXCLKA – LFIA VCC TXDA [6] TXDA [2] GND RFEN A TXOP A TXRST TXCLKO – GND RXDD [0] RXDD [6] VCC RXCLKD – LFID TXDD [7] TXDD [5] Y RXDA [7] RXDA [8] RXCLKA + TXDA [9] VCC TXDA [5] TXDA [0] GND TXPER TXCLKA A GND RXDD [2] RXDD [7] VCC RXCLKD + RXDD [9] TXCLK D TXDD [6] VCC N/C RXOP D TXCLKO + Note: 3. N/C = Do Not Connect Document #: 38-02057 Rev. *G Page 6 of 29 CYP15G0402DXB CYV15G0402DXB Pin Descriptions CYP(V)15G0402DXB Quad HOTLink II™ SERDES Name I/O Characteristics Signal Description Transmit Path Data Signals TXPERA TXPERB TXPERC TXPERD LVTTL1 Output, changes relative to REFCLK↑[4] Transmit Path Parity Error. Active HIGH. Asserted (HIGH) if parity checking is enabled and a parity error is detected at the shifter. This output is HIGH for one transmit character clock period to indicate detection of a parity error in the character presented to the shifter. If a parity error is detected, the character in error is replaced with the 10-bit character, 1001111000, to force a corresponding bad-character detection at the remote end of the link. This replacement takes place only when parity checking is enabled (PARCTL ≠ LOW). When BIST is enabled for the specific transmit channel, BIST progress is presented on these outputs. Once every 511 character times, the associated TXPERx signal will pulse HIGH for one transmit-character clock period to indicate a complete pass through the BIST sequence. These outputs also provide indication of a transmit Phase-Align Buffer underflow or overflow. When the transmit Phase-Align Buffers are enabled (TXCKSEL ≠ LOW, or TXCKSEL = LOW and TXRATE = HIGH), if an underflow or overflow condition is detected, TXPERx for the channel in error is asserted and remains asserted until either an atomic Word Sync Sequence is transmitted or TXRST is sampled LOW to re-center the transmit Phase-Align Buffers. TXDA[9:0] TXDB[9:0] TXDC[9:0] TXDD[9:0] LVTTL Input, Transmit Data Inputs. These inputs are captured on the rising edge of the transmit synchronous, interface clock as selected by TXCKSEL and passed to the transmit shifter. sampled by the TXDx[9:0] specify the specific transmission character to be sent. respective TXCLKx↑ or REFCLK↑[4] TXOPA TXOPB TXOPC TXOPD LVTTL Input, Transmit Path Odd Parity. When parity checking is enabled (PARCTL ≠ LOW), the synchronous, ODD parity captured at these inputs is XORed with the bits on the associated TXDx bus sampled by the to verify the integrity of the captured character. respective TXCLKx↑ or REFCLK↑[4] Transmit Path Clock and Control TXCLKO± LVTTL Output Transmit Clock Output. This true and complement clock is synthesized by the transmit PLL and is synchronous to the internal transmit character clock. It has the same frequency as REFCLK (when TXRATE = LOW), or twice the frequency of REFCLK (when TXRATE = HIGH). This output clock has no direct phase relationship to REFCLK. TXCKSEL Three-level Select[5] Transmit Clock Select. Static Control Input Selects the clock source used to write data into the transmit Input Register of the transmit channel(s) When LOW, all four input registers are clocked by REFCLK↑. When TXCKSEL is MID, TXCLKx↑ is used as the input register clock for the associated TXDx[9:0] and TXOPx. When HIGH, TXCLKA↑ is used to clock data into the Input Register for all channels. When TXCKSEL = MID or HIGH (TXCLKx or TXCLKA selected to clock input register), TXRATE = HIGH (Half-rate REFCLK) is an invalid mode of operation. TXCLKA TXCLKB TXCLKC TXCLKD LVTTL Clock Input asynchronous, internal pull-up Transmit Path Input Clocks. These inputs are only used when TXCKSEL ≠ LOW. These clocks must be frequency-coherent to REFCLK, but may be offset in phase. The internal operating phase of each input clock (relative to REFLCK or TXCLKO±) is adjusted when TXRST = LOW and locked when TXRST = HIGH. Notes: 4. When REFCLK is configured for half-rate operation (TXRATE = HIGH), these inputs are sampled (or the outputs change) relative to both the rising and falling edges of REFCLK 5. Three-level select inputs are used for static configuration. They are ternary (not binary) inputs that make use of non-standard logic levels of LOW, MID, and HIGH. The LOW level is usually implemented by direct connection to VSS (ground). The HIGH level is usually implemented by direct connection to VCC. When not connected or allowed to float, a three-level select input will self-bias to the MID level. Document #: 38-02057 Rev. *G Page 7 of 29 CYP15G0402DXB CYV15G0402DXB Pin Descriptions CYP(V)15G0402DXB Quad HOTLink II™ SERDES (continued) Name TXRATE I/O Characteristics Signal Description LVTTL Input, asynchronous, internal pull-up Transmit PLL Clock Rate Select. When TXRATE = HIGH, the Transmit PLL multiplies REFCLK by 20 to generate the serial bit-rate clock. When TXRATE = LOW, the transmit PLL multiples REFCLK by 10 to generate the serial bit-rate clock. See Table 3 for a list of operating serial rates. When TXCKSEL = MID or HIGH (TXCLKx or TXCLKA selected to clock input register), TXRATE = HIGH (Half-rate REFCLK) is an invalid mode of operation. TXRST LVTTL Input, asynchronous, internal pull-up, sampled by REFCLK↑ [4] Transmit Clock Phase Reset. Active LOW. When sampled LOW, the transmit Phase-align Buffers are allowed to adjust their data-transfer timing (relative to the selected input clock) to allow clean transfer of data from the Input Register to the Transmit Shifter. When TXRST is sampled HIGH, the internal phase relationship between the associated TXCLKx and the internal character-rate clock is fixed and the device operates normally. When configured for half-rate REFCLK sampling of the transmit character stream (TXCKSEL = LOW and TXRATE = HIGH), assertion of TXRST is only used to clear Phase-align buffer faults caused by highly asymmetric REFCLK periods or REFCLKs with excessive cycle-to-cycle jitter. During this alignment period, one or more characters may be added to or lost from all the associated transmit paths as the transmit Phase-align Buffers are adjusted. TXRST must be sampled LOW by a minimum of two consecutive rising edges of REFCLK to ensure the reset operation is initiated correctly on all channels. This input is ignored when both TXCKSEL and TXRATE are LOW, since the phase align buffer is bypassed. In all other configurations, TXRST should be asserted during device initialization to ensure proper operation of the Phase-align buffer. TXRST should be asserted after the assertion and deassertion of TRSTZ, after the presence of a valid TXCLKx and after allowing enough time for the TXPLL to lock to the reference clock (as specified by parameter tTXLOCK). Receive Path Data Signals RXDA[9:0] RXDB[9:0] RXDC[9:0] RXDD[9:0] LVTTL Output, synchronous to the selected RXCLKx↑ Receive Data Output. These outputs change following the rising edge of the selected receive interface clock. COMDETA COMDETB COMDETC COMDETD LVTTL Output, synchronous to the selected RXCLKx↑ Frame Character Detected. COMDETx = HIGH indicates the presence of a Framing character in that Output Register. RXOPA RXOPB RXOPC RXOPD Three-state, LVTTL Output, synchronous to the selected RXCLKx↑ output Receive Path Odd Parity. When parity generation is enabled (PARCTL ≠ LOW), the parity output at these pins is valid for the data on the associated RXDx bus bits. When parity generation is disabled (PARCTL = LOW) these output drivers are disabled (High-Z). Receive Path Clock and Clock Control RFENA RFENB RFENC RFEND LVTTL Input, asynchronous, internal pull-down Reframe Enable. Active HIGH. When HIGH the framer for the associated channel is enabled to frame as per the presently enabled framing mode and selected framing character. RXRATE LVTTL Input Static Control Input Receive Clock Rate Select.When LOW, the RXCLKx± recovered clock outputs are complementary clocks operating at the recovered character rate. Data for the associated receive channels should be latched on the rising edge of RXCLKx+ or falling edge of RXCLKx–. When HIGH, the RXCLKx± recovered clock outputs are complementary clocks operating at half the character rate. Data for the associated receive channels should be latched alternately on the rising edge of RXCLKx+ and RXCLKx–. Document #: 38-02057 Rev. *G Page 8 of 29 CYP15G0402DXB CYV15G0402DXB Pin Descriptions CYP(V)15G0402DXB Quad HOTLink II™ SERDES (continued) Name FRAMCHAR I/O Characteristics Signal Description Three-level Select [5] Framing Character Select. Used to control the type of character used for framing the Static Control Input received data streams. When MID, the framer looks for both positive and negative disparity versions of the eight-bit Comma character. When HIGH, the framer looks for both positive and negative disparity versions of the K28.5 character. Configuring FRAMCHAR to LOW is reserved for component test. RXCLKA± RXCLKB± RXCLKC± RXCLKD± LVTTL Output Clock Receive Character Clock Output. These true and complement clocks are the Receive interface clocks which are used to control timing of data output transfers. These clocks are output continuously at either the dual-character rate (1/20th the serial bit-rate) or character rate (1/10th the serial bit-rate) of the data being received, as selected by RXRATE. RFMODE Three-level Select[5] Reframe Mode Select. Used to control the type of character framing used to adjust the Static Control Input character boundaries (based on detection of one or more framing characters in the received serial bit stream). This signal operates in conjunction with the type of framing character selected. When LOW, the Low-Latency Framer is selected. This will frame on each occurrence of the selected framing character(s) in the received data stream. This mode of framing stretches the recovered character clock for one or multiple cycles to align that clock with the recovered data. When MID, the Cypress-mode Multi-Byte parallel Framer is selected. This requires a pair of the selected framing character(s), on identical 10-bit boundaries, within a span of 50 bits, before the character boundaries are adjusted. The recovered character clock remains in the same phase regardless of character offset. When HIGH, the alternate mode Multi-Byte parallel Framer is selected. This requires detection of the selected framing character(s) of the allowed disparities in the received serial bit stream, on identical 10-bit boundaries, on four directly adjacent characters. The recovered character clock remains in the same phase regardless of character offset. Device Control Signals PARCTL Three-level Select[5], Parity Check/Generate Control. Used to control the different parity check and Static Control Input generate functions. When LOW, parity checking is disabled, and the RXOPx outputs are all disabled (High-Z). When MID, theTXDx[9:0] inputs are checked (along with TXOPx) for valid ODD parity, and ODD parity is generated for the RXDx[9:0] outputs and presented on RXOPx. When HIGH, parity checking and generation are enabled. The TXDx[9:0] inputs are checked (along with TXOPx) for valid ODD parity, and ODD parity is generated for the RXDx[9:0] and COMDETx outputs and presented on RXOPx. See Table 8 for details. REFCLK± Differential LVPECL Reference Clock. This clock input is used as the timing reference for the transmit PLL. or single-ended It is also used as the centering frequency of the Range Controller block of the Receive LVCMOS input clock CDR PLLs. This input clock may also be selected to clock the transmit input interface. When driven by a a single-ended LVCMOS or LVTTL clock source, connect the clock source to either the true or complement REFCLK input and leave the alternate REFCLK input open (floating). When driven by an LVPECL clock source, the clock must be a differential clock, using both inputs. When TXCKSEL = LOW, REFCLK is also used as the clock for the parallel transmit data (input) interface. SPDSEL Three-level Select[5], Serial Rate Select. This input specifies the operating bit-rate range of both transmit and Static Control Input receive PLLs. LOW = 195–400 MBaud, MID = 400–800 MBaud, HIGH = 800–1500 MBaud. When SPDSEL is LOW, setting TXRATE = HIGH (Half-rate Reference Clock) is invalid. Document #: 38-02057 Rev. *G Page 9 of 29 CYP15G0402DXB CYV15G0402DXB Pin Descriptions CYP(V)15G0402DXB Quad HOTLink II™ SERDES (continued) Name I/O Characteristics Signal Description Analog I/O and Control OUTA± OUTB± OUTC± OUTD± CML Differential Output Differential Serial Data Outputs. These PECL-compatible CML outputs (+3.3V referenced) are capable of driving terminated transmission lines or standard fiber-optic transmitter modules. INA± INB± INC± IND± LVPECL Differential Differential Serial Data Inputs. These inputs accept the serial data stream for deseriInput alization. The INx± serial streams are passed to the receiver Clock and Data Recovery (CDR) circuits to extract the data content when INSELx = HIGH. OELE LVTTL Input, asynchronous, internal pull-up Serial Driver Output Enable Latch Enable. When OELE = HIGH, the signals on the BOE[7:0] inputs directly control the OUTx± differential drivers. When the BOE[x] input is HIGH, the associated OUTx± differential driver is enabled. When the BOE[x] input is LOW, the associated OUTx± differential driver is powered down. When OELE returns LOW, the last values present on BOE[7:0] are captured in the internal Output enable Latch. The specific mapping of BOE[7:0] signals to transmit output enables is listed in Table 2. If the device is reset (TRSTZ is sampled LOW), the latch is reset to disable all outputs. BISTLE LVTTL Input, asynchronous, internal pull-up Transmit and Receive BIST Latch Enable. Active HIGH. When BISTLE = HIGH, the signals on the BOE[7:0] inputs directly control the transmit and receive BIST enables. When the BOE[x] input is LOW, the associated transmit or receive channel is configured to generate or compare the BIST sequence. When the BOE[x] input is HIGH, the associated transmit or receive channel is configured for normal data transmission or reception. When BISTLE returns LOW the last values present on BOE[7:0] are captured in the internal BIST Enable Latch. The specific mapping of BOE[7:0] signals to transmit and receive BIST enables is listed in Table 2. When the latch is closed, if the device is reset (TRSTZ is sampled LOW), the latch is reset to disable BIST on all transmit and receive channels. RXLE LVTTL Input, asynchronous, internal pull-up Receive Channel Power-Control Latch Enable. When RXLE = HIGH, the signals on the BOE[7:0] directly control the power enables for the receive PLLs and analog logic. When the BOE[7:0] input is HIGH, the receive channels PLL’s and analog logic are active. When the BOE[7:0] input is LOW, the receive channels are in a power-down mode. When RXLE returns LOW, the last values present on BOE[7:0] are captured in the internal RX PLL Enable Latch. The specific mapping of BOE[7:0] signals to the associated receive channel enables is listed in Table 2. When the device is reset (TRSTZ = LOW), the latch is reset to disable all receive channels. BOE[7:0] LVTTL Input, asynchronous, internal pull-up BIST, Serial Output, and Receive Channel Enables. These inputs are passed to and through the Output Enable Latch when OELE is HIGH, and captured in this latch when OELE returns LOW. These inputs are passed to and through the BIST Enable Latch when BISTLE is HIGH, and captured in this latch when BISTLE returns LOW. These inputs are passed to and through the Receive Channel Enable Latch when RXLE is HIGH, and captured in this latch when RXLE returns LOW. Document #: 38-02057 Rev. *G Page 10 of 29 CYP15G0402DXB CYV15G0402DXB Pin Descriptions CYP(V)15G0402DXB Quad HOTLink II™ SERDES (continued) Name I/O Characteristics Signal Description SDASEL Three-level Select[5], Signal Detect Amplitude Level Select. Allows selection of one of three predefined static configuration amplitude trip points for a valid signal indication, as listed in Table 4. input LPENA LPENB LPENC LPEND LVTTL Input, asynchronous, internal pull-down Loop-Back-Enable. Active HIGH. When asserted (HIGH), the transmit serial data from the associated channel is internally routed to its respective receiver clock and data recovery (CDR) circuit. The serial output for the channel where LPENx is active is forced to differential logic “1”, and serial data inputs for that channel are ignored. LFIA LFIB LFIC LFID LVTTL Output, Asynchronous Link Fault Indication Output. Active LOW. LFIx is the logical OR of four internal conditions: 1. Received serial data frequency outside expected range 2. Analog amplitude below expected levels 3. Transition density lower than expected 4. Receive Channel disabled. TRSTZ LVCMOS Input, internal pull-up Device Reset. Active LOW. Initializes all state machines and counters in the device. When sampled LOW by the rising edge of REFLCK, this input resets the internal state machines and sets the Elasticity Buffer pointers to a nominal offset. When the reset is removed (TRSTZ sampled HIGH by REFCLK↑), the status and data outputs will become deterministic in fewer than 16 REFCLK cycles. The BISTLE, OELE, and RXLE latches are reset by TRSTZ. If the Elasticity Buffer or the Phase Align Buffer are used, TRSTZ should be applied after power up to initialize the internal pointers into these memory arrays. JTAG Interface TMS LVTTL Input, internal pull-up Test Mode Select. Used to control access to the JTAG Test Modes. If maintained high for >5 TCLK cycles, the JTAG test controller is reset. The TAP controller is also reset automatically upon application of power to the device. TCLK LVTTL Input, internal pull-down JTAG Test Clock TDO Three-state LVTTL Output Test Data Out. JTAG data output buffer which is High-Z while JTAG test mode is not selected. TDI LVTTL Input, internal pull-up Test Data In. JTAG data input port. Power VCC +3.3V Power GND Signal and Power Ground for all internal circuits. CYP(V)15G0402DXB HOTLink II SERDES Operation The CYP(V)15G0402DXB is a highly configurable device designed to support reliable transfer of large quantities of data using high-speed serial links from one or multiple sources to multiple destinations. This device supports four characterwide channels. CYP(V)15G0402DXB Transmit Data Path Data Path The transmit path of the CYP(V)15G0402DXB supports four character-wide data paths. These four data paths are internally unencoded and require 10-bit input data that may be pre-encoded or scrambled to achieve sufficient transition density. Input Register The bits in the Input Register for each channel have fixed bit assignments, as listed in Table 1. Each input register captures a minimum of 10 bits on each input clock cycle. When parity checking is enabled, the TXOPx parity input is also captured in the associated input register. Input Register Clocking The transmit Input Registers can be configured to accept data relative to different clock sources. The selection of the clock source is controlled by TXCKSEL. When TXCKSEL = LOW, the Input Registers for all four transmit channels are clocked by REFCLK↑[4]. When TXCKSEL = HIGH, the Input Registers for all four transmit channels are clocked with TXCLKA↑. When TXCKSEL is MID, TXCLKx↑ is used as the input register clock for the associated TXDx[9:0] and TXOPx. Document #: 38-02057 Rev. *G Page 11 of 29 CYP15G0402DXB CYV15G0402DXB Table 1. Input Register Bit Mapping Signal Name Bus Weight [6] 20 TXDx[0] (LSB) TXDx[1] 21 TXDx[2] 22 TXDx[3] 23 TXDx[4] 24 TXDx[5] 25 TXDx[6] 26 TXDx[7] 27 TXDx[8] 28 29 TXDx[9] (MSB) [7] TXOPx 10B Name a b c d e i f g h j Phase-Align Buffer Data from the Input Registers is normally routed to the associated Phase-Align Buffer. When the transmit paths are operated synchronous to REFCLK↑ (TXCKSEL = LOW and TXRATE = LOW), the Phase-Align Buffers are bypassed and data is passed directly to the Parity Check and Serializer blocks to reduce latency. When an Input-Register clock with an uncontrolled phase relationship to REFCLK is selected (TXCKSEL ≠ LOW) or if data is captured on both edges of REFCLK (TXRATE = HIGH), the Phase-Align Buffers are enabled. These buffers are used to absorb clock phase differences between the presently selected input clock and the internal character clock. Initialization of these Phase-Align Buffers takes place when the TXRST input is sampled LOW by two consecutive rising edges of REFCLK↑. When TXRST is returned HIGH, the present input clock phase relative to REFCLK is set. TXRST is an asynchronous input, but is sampled internally to synchronize it to the internal transmit path state machines. Once set, the input clocks are allowed to skew in time up to half a character period in either direction relative to REFCLK; i.e., ±180°. This time shift allows the delay paths of the character clocks (relative to REFCLK) to change due to operating voltage and temperature, while not affecting reliable data transfer. If the phase offset, between the initialized location of the input clock and REFCLK↑, exceeds the skew handling capabilities of the Phase-Align Buffer, an error is reported on the associated TXPERx output. This output indicates a continuous error until the Phase-Align Buffer is reset. While the error remains active, the transmitter for the associated channel will output a continuous 10-bit character, 1001111000b, to indicate to the remote receiver that an error condition is present in the link. Parity Support In addition to the ten data bits that are captured at each channel, a TXOPx input is also available on each channel. This allows the CYP(V)15G0402DXB to support ODD parity checking for each channel. When PARCTL = LOW, parity checking is disabled. When PARCTL = MID or HIGH, parity is checked on the TXDx[9:0] and TXOPx bits. If parity checking is enabled (PARCTL ≠ LOW) and a parity error is detected, the 10-bit character in error is replaced with the 1001111000b pattern (an invalid character). Transmit BIST The transmitter interfaces contain internal pattern generators that can be used to validate both device and link operation. These generators are enabled by the associated BOE[x] signals listed in Table 2 (when the BISTLE latch enable input is HIGH). When enabled, a register in the associated transmit channel becomes a signature pattern generator by logically converting to a Linear Feedback Shift Register (LFSR). This LFSR generates a 511-character sequence that includes all Data and Special Character codes, including the explicit violation symbols. This provides a predictable yet pseudo-random sequence that can be matched to an identical LFSR in the attached Receiver(s). When the BISTLE signal is HIGH, any BOE[x] input that is LOW enables the BIST generator in the associated transmit channel (or the BIST checker in the associated receive channel). When BISTLE returns LOW, the values of all BOE[x] signals are captured in the BIST Enable Latch. These values remain in the BIST Enable Latch until BISTLE is returned HIGH to open the latch. A device reset (TRSTZ sampled LOW) presets the BIST Enable Latch to disable BIST on all channels. All data and data-control information present at the associated TXDx[9:0] inputs are ignored when BIST is active on that channel. Table 2. Output Enable, BIST, and Receive Channel Enable Signal Map Output Controlled (OELE) BIST Channel Enable (BISTLE) BOE[7] X Transmit D X BOE[6] OUTD± Receive D Receive D BOE[5] X Transmit C X BOE[4] OUTC± Receive C Receive C BOE[3] X Transmit B X BOE[2] OUTB± Receive B Receive B BOE[1] X Transmit A X BOE[0] OUTA± Receive A Receive A BOE Input Receive PLL Channel Enable (RXLE) Serial Output Drivers The serial interface Output Drivers use differential CML (Current Mode Logic) to provide a source-matched driver for the transmission lines. These drivers accept data from the Transmit Shifters. These outputs have signal swings equivalent to that of standard PECL drivers and are capable of driving AC-coupled optical modules or transmission lines. Notes: 6. LSB is shifted out first. 7. The TXOPx inputs are also captured in the associated Input Register, but their interpretation is under the separate control of PARCTL. Document #: 38-02057 Rev. *G Page 12 of 29 CYP15G0402DXB CYV15G0402DXB When configured for local loopback (LPENx = HIGH), the output drivers for all enabled ports are configured to drive a static differential logic-1. Each output can be enabled or disabled separately through the BOE[7:0] inputs, as controlled by the OELE latch-enable signal. When OELE is HIGH, the signals present on the BOE[7:0] inputs are passed through the Serial Output Enable Latch to control the Serial Output Drivers. The BOE[7:0] input associated with a specific OUTx± driver is listed in Table 2. When OELE is HIGH and BOE[x] is HIGH, the associated Serial Driver is enabled. When OELE is HIGH and BOE[x] is LOW, the associated driver is disabled and internally powered down, the associated internal logic for that channel is also powered down. When OELE returns LOW, the values present on the BOE[7:0] inputs are latched in the Output Enable Latch, and remain there until OELE returns HIGH to enable the latch. A device reset (TRSTZ sampled LOW) clears this latch and disables all output drivers. NOTE: When all transmit channels are disabled (i.e., both serial output drivers disabled in all channels) and a serial output driver is re-enabled, the data on the Serial Drivers may not meet all timing specifications for up to 200 µs. Transmit PLL Clock Multiplier The Transmit PLL Clock Multiplier accepts a character-rate or half-character-rate external clock at the REFCLK input, and multiples that clock by 10 or 20 (as selected by TXRATE) to generate a bit-rate clock for use by the Transmit Shifter. It also provides a character-rate clock used by the transmit paths. The clock multiplier PLL can accept a REFCLK input between 19.5 MHz and 150 MHz, however, this clock range is limited by the operating mode of the CYP(V)15G0402DXB clock multiplier (controlled by TXRATE) and by the level on the SPDSEL input. When TXCKSEL = MID or HIGH (TXCLKx or TXCLKA selected to clock input register), TXRATE = HIGH (Half-rate REFCLK) is an invalid mode of operation. SPDSEL is a three-level select[5] (ternary) input that selects one of three operating ranges for the serial data outputs and inputs. The operating serial signaling-rate and allowable range of REFCLK frequencies is listed in Table 3. Table 3. Operating Speed Settings SPDSEL TXRATE REFCLK Frequency (MHz) LOW 1 reserved 0 19.5–40 MID (Open) 1 20–40 0 40–80 HIGH 1 40–75 0 80–150 Signaling Rate (MBaud) 195-400 400–800 The REFCLK± input is a differential input with each input internally biased to 1.4V. If the REFCLK+ input is connected to a TTL, LVTTL, or LVCMOS clock source, the input signal is recognized when it passes through the internally biased reference point and REFCLK- can be left floating. When both the REFCLK+ and REFCLK– inputs are connected, the clock source must be a differential clock. This can be either a differential LVPECL clock that is DC- or AC-coupled, or a differential LVTTL or LVCMOS clock. By connecting the REFCLK– input to an external voltage source or resistive voltage divider, it is possible to adjust the reference point of the REFCLK+ input for alternate logic levels. When doing so it is necessary to ensure that the input differential crossing point remains within the parametric range supported by the input. CYP(V)15G0402DXB Receive Data Path Serial Line Receivers A differential line receiver, INx±, is available on each channel for accepting a serial bit stream. The Serial Line Receiver inputs are differential, and can accommodate wire interconnect and filtering losses or transmission line attenuation greater than 16 dB. For normal operation, these inputs should receive a signal of at least VIDIFF > 100 mV, or 200 mV peak-to-peak differential. Each Line Receiver can be DC- or AC-coupled to +3.3V powered fiber-optic interface modules (any ECL/PECL family, not limited to 100K PECL) or AC-coupled to +5V powered optical modules. The common-mode tolerance of these line receivers accommodates a wide range of signal termination voltages. Each receiver provides internal DC-restoration, to the center of the receiver’s common mode range, for AC-coupled signals. The local loopback inputs (LPENx) for each channel allows the serial transmit data outputs to be routed internally back to the Clock and Data Recovery circuit associated with that channel. When configured for local loopback, all transmit Serial Driver outputs are forced to output a differential logic-1. This prevents local diagnostic patterns from being broadcast to attached remote receivers. Signal Detect/ Link Fault Each selected Line Receiver is simultaneously monitored for • analog amplitude above limit specified by SDASEL • transition density greater than specified limit • CDR tracking data within expected frequency range as defined by REFCLK and TXRATE (± 1500 ppm)[8] • receive channel enabled All of these conditions must be valid for the Signal Detect block to indicate a valid signal is present. This status is presented on the LFIx (Link Fault Indicator) output associated with each receive channel. 800–1500 Note: 8. REFCLK has no phase or frequency relationship with the recovered clock(s) and only acts as a centering reference to reduce clock synchronization time. REFCLK must be within ±1500 PPM (±0.15%) of the remote transmitter’s PLL reference (REFCLK) frequency. Although transmitting to a HOTLink II receiver necessitates the frequency difference between the transmitter and receiver reference clocks to be within ±1500 ppm, the stability of the crystal needs to be within the limits specified by the appropriate standard when transmitting to a remote receiver that is compliant to that standard. For example, to be IEEE 802.3z Gigabit Ethernet compliant, the frequency stability of the crystal needs to be within ±100 ppm. Document #: 38-02057 Rev. *G Page 13 of 29 CYP15G0402DXB CYV15G0402DXB Analog Amplitude While most signal monitors are based on fixed constants, the analog amplitude level detection is adjustable. This allows operation with highly attenuated signals, or in high-noise environments. This adjustment is made through the SDASEL signal, a three-level select[5] input, which sets the trip point for the detection of a valid signal at one of three levels, as listed in Table 4. This control input affects the analog monitors for all receive channels. When a particular channel is configured for local loopback (LPENx = HIGH), no line receivers are selected, and the LFIx output for each channel reports only the receive VCO frequency out-of-range and transition density status of the associated transmit signal. When local loopback is active, the Analog Signal Detect Monitors are disabled. Table 4. Analog Amplitude Detect Valid Signal Levels[9] SDASEL LOW Typical Signal with Peak Amplitudes Above 140 mV p-p differential MID (Open) 280 mV p-p differential HIGH 420 mV p-p differential Transition Density The Transition Detection logic checks for the absence of any transitions spanning greater than six transmission characters (60 bits). If no transitions are present in the data received on a channel, the Transition Detection logic for that channel will assert LFIx. The LFIx output remains asserted until at least one transition is detected in each of three adjacent received characters. Range Controls The Clock/Data Recovery (CDR) circuit includes logic to monitor the frequency of the Phase Locked Loop (PLL) Voltage Controlled Oscillator (VCO) used to sample the incoming data stream. This logic ensures that the VCO operates at, or near the rate of the incoming data stream for two primary cases: • when the incoming data stream resumes after a time in which it has been “missing” • when the incoming data stream is outside the acceptable frequency range To perform this function, the frequency of the VCO is periodically sampled and compared to the frequency of the REFCLK input. If the VCO is running at a frequency beyond +1500ppm[8] as defined by the reference clock frequency, it is periodically forced to the correct frequency (as defined by REFCLK, SPDSEL, and TXRATE) and then released in an attempt to lock to the input data stream. The sampling and relock period of the Range Control is calculated as follows: RANGE CONTROL SAMPLING PERIOD = (REFCLKPERIOD) * (16000). During the time that the Range Control forces the PLL VCO to run at REFCLK*10 (or REFCLK*20 when TXRATE = HIGH) rate, the LFIx output will be asserted LOW. While the PLL is attempting to re-lock to the incoming data stream, LFIx may be either HIGH or LOW (depending on other factors such as transition density and amplitude detection) and the recovered byte clock (RXCLKx) may run at an incorrect rate (depending on the quality or existence of the input serial data stream). After a valid serial data stream is applied, it may take up to one RANGE CONTROL SAMPLING PERIOD before the PLL locks to the input data stream, after which LFIx should be HIGH. Receive Channel Enabled The CYP(V)15G0402DXB contains four receive channels that can be independently enabled and disabled. Each channel can be enabled or disabled separately through the BOE[7:0] inputs, as controlled by the RXLE latch-enable signal. When RXLE is HIGH, the signals present on the BOE[7:0] inputs are passed through the Receive Channel Enable Latch to control the PLLs and logic of the associated receive channel. The BOE[7:0] input associated with a specific receive channel is listed in Table 2. When RXLE is HIGH and BOE[x] is HIGH, the associated receive channel is enabled to receive and recover a serial stream. When RXLE is HIGH and BOE[x] is LOW, the associated receive channel is disabled and powered down. Any disabled channel will indicate an asserted LFIx output. When RXLE returns LOW, the values present on the BOE[7:0] inputs are latched in the Receive Channel Enable Latch, and remain there until RXLE returns HIGH to open the latch again.[10] Clock/Data Recovery The extraction of a bit-rate clock and recovery of bits from each received serial stream is performed by a separate Clock/Data Recovery (CDR) block within each receive channel. The clock extraction function is performed by embedded phase-locked loops (PLLs) that track the frequency of the transitions in the incoming bit streams and align the phase of their internal bit-rate clocks to the transitions in the selected serial data streams. Each CDR accepts a character-rate (bit-rate ÷ 10) or half-character-rate (bit-rate ÷ 20) reference clock from the REFCLK input. This REFCLK input is used to • ensure that the VCO (within the CDR) is operating at the correct frequency. • to reduce PLL acquisition time • and to limit unlocked frequency excursions of the VCO when there is no input data present at the selected Serial Line Receiver. Regardless of the type of signal present, the CDR will attempt to recover a data stream from it. If the frequency of the recovered data stream is outside the limits of the range control monitor, the CDR will switch to track REFCLK instead of the data stream. Once the CDR output (RXCLKx) frequency returns back close to REFCLK frequency, the CDR input will be switched back to track the input data stream. Notes: 9. The peak amplitudes listed in this table are for typical waveforms that have generally 3 – 4 transitions for every ten bits. In a worse case environment the signals may have a sign-wave appearance (highest transition density with repeating 0101...). Signal peak amplitudes levels within this environment type could increase the values in the table above by approximately 100 mV. 10. When a disabled receive channel is reenabled, the status of the associated LFIx output and data on the parallel outputs for the associated channel may be indeterminate for up to 2 ms. Document #: 38-02057 Rev. *G Page 14 of 29 CYP15G0402DXB CYV15G0402DXB In case no data is present at the input, this switching behavior may result in brief RXCLKx frequency excursions from REFCLK. However, the validity of the input data stream is indicated by the LFIx output. The frequency of REFCLK is required to be within ±1500ppm[8] of the frequency of the clock that drives the REFCLK input of the remote transmitter to ensure a lock to the incoming data stream. output clock (RXRATE = LOW), the output of properly framed characters may be delayed by up to nine character-clock cycles from the detection of the selected framing character. When operated with a half-character-rate output clock (RXRATE = HIGH), the output of properly framed characters may be delayed by up to 14 character-clock cycles from the detection of the selected framing character.[8] Deserializer/Framer When RFMODE is MID (open), the Cypress-mode Multi-Byte Framer is selected. The required detection of multiple framing characters makes the associated link much more robust to incorrect framing due to aliased framing characters in the data stream. In this mode, the Framer does not adjust the character clock boundary, but instead aligns the character to the already recovered character clock. This ensures that the recovered clock will not contain any significant phase changes or hops during normal operation or framing, and allows the recovered clock to be replicated and distributed to other external circuits or components using PLL-based clock distribution elements. In this framing mode, the character boundaries are only adjusted if the selected framing character is detected at least twice within a span of 50 bits, with both instances on identical 10-bit character boundaries. Each CDR circuit extracts bits from the associated serial data stream and clocks these bits into the Shifter/Framer at the bit-clock rate. When enabled, the Framer examines the data stream, looking for one or more Comma or K28.5 characters at all possible bit positions. The location of this character in the data stream is used to determine the character boundaries of all following characters. Framing Character The CYP(V)15G0402DXB allows selection of one of two combinations of framing characters to support requirements of different interfaces. The selection of the framing character is made through the FRAMCHAR input. Table 5. Framing Character Selector Bits Detected in Framer FRAMCHAR Character Name LOW Bits Detected Reserved for test MID (Open) Comma+ or Comma- 00111110XX[11] or 11000001XX HIGH +K28.5 or -K28.5 0011111010 or 1100000101 When RFMODE = HIGH, the Alternate-mode Multi-Byte Framer is enabled. Like the Cypress-mode Multi-Byte Framer, multiple framing characters must be detected before the character boundary is adjusted. In this mode, the Framer does not adjust the character clock boundary, but instead aligns the character to the already recovered character clock. In this mode, the data stream must contain a minimum of four of the selected framing characters, received as consecutive characters, on identical 10-bit boundaries, before character framing is adjusted. The specific bit combinations of these framing characters are listed in Table 5. When the specific bit combination of the selected framing character is detected by the Framer, the boundaries of the characters present in the received data stream are known. Framing is enabled for a channel when the associated RFENx input is HIGH. When RFENx is LOW, the framer for the associated channel is disabled. When a framer is disabled, no changes are made to the recovered character boundaries on that channel, regardless of the presence of framing characters in the data stream. Framer Receive BIST Operation The Framer on each channel operates in one of three different modes, as selected by the RFMODE input. In addition, the Framer for each channel may be enabled or disabled through the RFENx input. When RFENx = LOW, the framer in that receive path is disabled, and no combination of bits in a received data stream will alter the character boundaries. When RFENx = HIGH, the Framer selected by RFMODE is enabled for that channel. The Receiver interfaces contain internal pattern generators that can be used to validate both device and link operation. These generators are enabled by the associated BOE[x] signals listed in Table 2 (when the BISTLE latch enable input is HIGH). When enabled, a register in the associated receive channel becomes a pattern generator and checker by logically converting to a Linear Feedback Shift Register (LFSR). This LFSR generates a 511-character sequence that includes all Data and Special Character codes, including the explicit violation symbols. This provides a predictable yet pseudo-random sequence that can be matched to an identical LFSR in the attached Transmitter(s). When synchronized with the received data stream, the associated Receiver compares each received character with each character generated by the LFSR and indicates compare errors and BIST status at the COMDETx and RXDx[1:0] bits of the Output Register[12]. When RFMODE = LOW, the Low-Latency Framer is selected. This Framer operates by stretching the recovered character clock until it aligns with the received character boundaries. In this mode, the Framer starts its alignment process on the first detection of the selected framing character. To reduce the impact on external circuits that make use of a recovered clock, the clock period is not stretched by more than two bit-periods in any one clock cycle. When operated with a character-rate Notes: 11. The standard definition of a Comma contains only seven bits. However, since all valid Comma characters within the 8B/10B character set also have the eighth bit as an inversion of the seventh bit, the compare pattern is extended to a full eight bits to reduce the possibility of a framing error. 12. When Receive BIST is enabled on a channel, the Low-Latency Framer must not be enabled. The BIST sequence contains an aliased K28.5 framing character, which causes the Receiver to update its character boundaries incorrectly. Document #: 38-02057 Rev. *G Page 15 of 29 CYP15G0402DXB CYV15G0402DXB The specific patterns checked by each receiver are described in detail in the Cypress application note “HOTLink Built-In Self-Test.” The sequence compared by the CYP(V)15G0402DXB is identical to that in the CY7B933 and CY7C924DX, allowing interoperable systems to be built when used at compatible serial signaling rates. If the number of invalid characters received ever exceeds the number of valid characters by 16, the receive BIST state machine aborts the compare operations and resets the LFSR to the D0.0 state to look for the start of the BIST sequence again. The BIST state machine requires the characters to be correctly framed for it to detect the BIST sequence. If the Low Latency Framer is enabled (RFMODE = LOW), the Framer will misalign to an aliased K28.5 framing character within the BIST sequence. If the Alternate Multi-Byte Framer is enabled (RFMODE = HIGH), it is necessary to frame the receiver before BIST is enabled. Power Control The CYP(V)15G0402DXB supports user control of the powered up or down state of each transmit and receive channel. The receive channels are controlled by the RXLE signal and the values present on the BOE[7:0] bus. The transmit channels are controlled by the OELE signal and the values present on the BOE[7:0] bus. Powering down unused channels will save power and reduce system heat generation. Controlling system power dissipation will improve the system performance. Receive Channels When RXLE is HIGH, the signals on the BOE[7:0] inputs directly control the power enables for the receive PLLs and analog circuits. When a BOE[7:0] input is HIGH, the associated receive channel [A through D] PLL and analog logic are active. When a BOE[7:0] input is LOW, the associated receive channel [A through D] PLL and analog circuits are powered down. When RXLE returns LOW, the last values present on the BOE[7:0] inputs are captured. The specific BOE[7:0] input signal associated with a receive channel is listed in Table 2. Any disabled receive channel will indicate a constant LFIx output. Document #: 38-02057 Rev. *G Priority Description RXDx[1] COMDETx, RXDx[1:0] indicates 010b or 100b for one character period per BIST loop to indicate loop completion. This status can be used to check test pattern progress. The status reported by the BIST state machine on COMDETX and RXDx[1:0] are listed in Table 6. Status RXDx[0] When BIST is first recognized as being enabled in the Receiver, the LFSR is preset to the BIST-loop start-code of D0.0. This code D0.0 is sent only once per BIST loop. The status of the BIST progress and any character mismatches is presented on the COMDETx and RXDx[1:0] status outputs. Table 6. BIST Status Bits COMDETx When the BISTLE signal is HIGH, any BOE[x] input that is LOW enables the BIST generator/checker in the associated Receive channel (or the BIST generator in the associated Transmit channel). When BISTLE returns LOW, the values of all BOE[x] signals are captured in the BIST Enable Latch. These values remain in the BIST Enable Latch until BISTLE is returned HIGH. All captured signals in the BIST Enable Latch are set HIGH (i.e., BIST is disabled) following a device reset (TRSTZ is switched LOW). 0 0 0 7 BIST Data Compare. Data Character compared correctly. 0 0 1 7 BIST Command Compare. Command Character compared correctly. 0 1 0 2 BIST Last Good. Last Character of BIST sequence detected and valid. 0 1 1 5 Reserved 1 0 0 4 BIST Last Bad. Last Character of BIST sequence was detected invalid. 1 0 1 1 BIST Start. RXBISTEN recognized on this channel, but character compares have not yet commenced. Also presented when the receive PLL is tracking REFCLK instead of the selected data stream. 1 1 0 6 BIST Error. While comparing characters, a mismatch was found in one or more of the decoded character bits. 1 1 1 3 BIST Wait. The receiver is comparing characters. but has not yet found the start of BIST character to enable the LFSR. BIST Mode When a disabled receive channel is re-enabled, the status of the associated LFIx output and data on the parallel outputs for the associated channel may be indeterminate for up to 2 ms. Transmit Channels When OELE is HIGH, the signals on the BOE[7:0] inputs directly control the power enables for the Serial Drivers. When a BOE[x] input is HIGH, the associated Serial Driver is enabled. When a BOE[x] input is LOW, the associated Serial Driver is disabled and powered down. If the Serial Driver of a channel is disabled, the internal logic for that channel is powered down. When OELE returns LOW, the values present on the BOE[7:0] inputs are latched in the Output Enable Latch. Device Reset State When the CYP(V)15G0402DXB is reset by assertion of TRSTZ, the Transmit Enable and Receive Enable Latches are both cleared, and the BIST Enable Latch is preset. In this state, all transmit and receive channels are disabled, and BIST is disabled on all channels. Following a device reset, it is necessary to enable the transmit and receive channels used for normal operation. This can be done by sequencing the appropriate values on the BOE[7:0] inputs while the OELE and RXLE signals are raised and lowered. For systems that do not require dynamic control of power, or want the part to power up in a fixed configuration, it is also possible to strap the RXLE and OELE control signals HIGH to permanently enable their associated latches. Connection of the associated BOE[7:0] signals to a stable HIGH will then enable the respective transmit and receive channels as soon as the TRSTZ signal is deasserted. Page 16 of 29 CYP15G0402DXB CYV15G0402DXB Output Bus Parity Generation Each receive channel presents a 12-signal output bus consisting of: • a 10-bit data bus • a COMMA detect indicator • a parity bit. The signals present on this output bus are shown inTable 7. Table 7. Output Register Bit Assignment Signal Name In addition to the 10-bit data and COMDETx status bit, an RXOPx ODD parity output can also be generated for each channel. Parity can be generated on • the RXDx[9:0] character • RXDx[9:0] character and COMDETx status bit. These modes differ in the number of bits which are included in the parity calculation. Only ODD parity is provided which ensures that at least one bit of the data bus is always a logic-1. Those bits covered by parity generation are listed in Table 8. Bus Weight 10B Name RXDx[0] (LSB) 20 a RXDx[1] 21 b RXDx[2] 22 c RXDx[3] 23 d RXDx[4] 24 e RXDx[5] 25 i Signal Name RXDx[6] 26 f COMDETx RXDx[7] 27 g RXDx[0] X X RXDx[8] 28 h RXDx[1] X X RXDx[9] (MSB) 29 j RXDx[2] X X RXDx[3] X X RXDx[4] X X RXDx[5] X X RXDx[6] X X RXDx[7] X X RXDx[8] X X RXDx[9] X X RXOPx[13] COMDETx[13] The framed 10-bit value is presented to the associated Output Register, along with a status output (COMDETx) indicating if the character in the output register matches the selected framing characters. The COMDETx output is HIGH when the character in the Output Register of the associated channel contains the selected framing character at the proper character boundary, and LOW for all other bit combinations. When the Low-Latency Framer and half-rate receive port clocking are also enabled (RFMODE = LOW, RXRATE = HIGH), the Framer will stretch the recovered clock to the nearest 20-bit boundary such that the rising edge of RXCLKx+ occurs when COMDETx is present on the associated output bus. When the Cypress or Alternate Mode Framer is enabled and half-rate receive port clocking are also enabled (RFMODE ≠ LOW and RXRATE = HIGH), the output clock is not modified when framing is detected, but a single pipeline stage may be added or subtracted from the data stream by the Framer logic such that the rising edge of RXCLKx+ occurs when COMDETx is present on the associated output bus. This adjustment only occurs when the Framer is enabled (RFEN = HIGH). When the Framer is disabled, the clock boundaries are not adjusted, and COMDETx may be asserted during the rising edge of RXCLK– (if an odd number of characters were received following the initial framing). Parity generation is enabled through the three-level select PARCTL input. When PARCTL = LOW, parity checking is disabled, and the RXOPx outputs are all disabled (High-Z). When PARCTL is MID, ODD parity is generated for the RXDx[9:0] bits. When PARCTL is HIGH, ODD parity is generated for both the RXDx[9:0] bits and the associated COMDETx signal. Table 8. Output Register Parity Generation Receive Parity Generate Mode (PARCTL) LOW[14] MID HIGH X[15] BIST Status State Machine When a receive path is enabled to look for and compare the received data stream with the BIST pattern, the COMDETx and RXDx[1:0] bits identify the present state of the BIST compare operation. The BIST state machine has multiple states, as shown in Figure 2 and Table 6. When the receive PLL detects an out-of-lock condition, the BIST state is forced to the Start-of-BIST state, regardless of the present state of the BIST state machine. If the number of detected errors ever exceeds the number of valid matches by greater than 16, the state machine is forced to the WAIT_FOR_BIST state where it monitors the interface for the first character (D0.0) of the next BIST sequence. Also, if the Elasticity Buffer ever hits an overflow/underflow condition, the status is forced to the BIST_START until the buffer is re-centered (approximately nine character periods). Notes: 13. The RXOPx and COMDETx outputs are also driven from the associated output register, but their generation and interpretation are separate from the data bus. 14. Receive path parity output drivers are disabled when PARCTL is low 15. When BIST is not enabled,COMDETx is usually driven to a logic 0, but will be driven high when the character in the output buffer is the selected framing character. Document #: 38-02057 Rev. *G Page 17 of 29 CYP15G0402DXB CYV15G0402DXB JTAG Support JTAG ID The CYP(V)15G0402DXB contains a JTAG port to allow system level diagnosis of device interconnect. Of the available JTAG modes, only boundary scan is supported. This capability is present only on the LVTTL inputs, LVTTL outputs and REFCLK± input. The high-speed serial signals are not part of the JTAG test chain. The JTAG device ID for the CYP(V)15G0402DXB is ‘1C801069’hex. Document #: 38-02057 Rev. *G Three-level Select Inputs Each three-level select input reports as two bits in the scan register. These bits report the LOW, MID, and HIGH state of the associated input as 00, 10, and 11, respectively. Page 18 of 29 CYP15G0402DXB CYV15G0402DXB Monitor Data Received COMDETX,RXDx[1:0] = BIST_START (101) Receive BIST Detected LOW RX PLL Out of Lock COMDETX,RXDx[1:0] = BIST_WAIT (111) No Start of BIST Detected YES COMDETX,RXDx[1:0] = BIST_COMMAND_COMPARE (001) OR BIST_DATA_COMPARE (000) Compare Next Character Mismatch COMDETX,RXDx[1:0] = Match BIST_COMMAND_COMPARE (001) Command Auto-Abort Condition Data or Command No Data End-of-BIST State End-of-BIST State Yes, COMDETX,RXDx[1:0] = BIST_LAST_BAD (100) Yes, COMDETX,RXDx[1:0] = BIST_LAST_GOOD (010) Yes COMDETX,RXDx[1:0] = BIST_DATA_COMPARE (000) No No, COMDETX,RXDx[1:0] = BIST_ERROR (110) Figure 2. Receive BIST State Machine Document #: 38-02057 Rev. *G Page 19 of 29 CYP15G0402DXB CYV15G0402DXB Maximum Ratings Static Discharge Voltage.......................................... > 2000 V (per MIL-STD-883, Method 3015) (Above which the useful life may be impaired. User guidelines only, not tested. Latch-up Current..................................................... > 200 mA Power-up Requirements Storage Temperature ................................. –65°C to +150°C The CYP(V)15G0402DXB requires one power supply. The voltage on any input or I/O pin cannot exceed the power pin during power-up. Ambient Temperature with Power Applied............................................. –55°C to +125°C DC Voltage Applied to LVTTL Outputs in High−Z State .......................................–0.5V to VCC + 0.5V Operating Range Supply Voltage to Ground Potential ............... –0.5V to +3.8V Output Current into LVTTL Outputs (LOW)..................60 mA Range Ambient Temperature VCC Commercial 0°C to +70°C 3.3V ± 5% –40°C to +85°C 3.3V ± 5% Industrial DC Input Voltage....................................–0.5V to VCC + 0.5V CYP(V)15G0402DXB DC Electrical Characteristics Over the Operating Range Parameter Description Test Conditions Min. Max. Unit 2.4 VCC V 0 0.4 V –20 –100 mA –20 20 mA 2.0 VCC + 0.3 V LVTTL-compatible Outputs VOHT Output HIGH Voltage IOH = –4 mA, VCC = Min. VOLT Output LOW Voltage IOL = 4 mA, VCC = Min. IOST Output Short Circuit Current IOZL High-Z Output Leakage Current VOUT = 0V[16] LVTTL-compatible Inputs VIHT Input HIGH Voltage VILT Input LOW Voltage IIHT Input HIGH Current IILT Input LOW Current IIHPDT Input HIGH Current with internal pull-down VIN = VCC IILPUT Input LOW Current with internal pull-up –200 µA –0.5 REFCLK Input, VIN = VCC 0.8 V +1.5 mA Other Inputs, VIN = VCC +40 µA REFCLK Input, VIN = 0.0V –1.5 mA –40 µA +200 µA Other Inputs, VIN = 0.0V VIN = 0.0V LVDIFF Inputs: REFCLK± VDIFF[17] Input Differential Voltage 400 VCC mV VIHHP Highest Input HIGH Voltage 1.2 VCC V VILLP Lowest Input LOW voltage 0.0 VCC/2 V VCOMREF[18] Common Mode Range 1.0 VCC – 1.2V V Three-level Inputs VIHH Three-level Input HIGH Voltage Min. ≤ VCC ≤ Max. 0.87 * VCC VCC V VIMM Three-level Input MID Voltage Min. ≤ VCC ≤ Max. 0.47 * VCC 0.53 * VCC V VILL Three-level Input LOW Voltage Min. ≤ VCC ≤ Max. 0.0 0.13 * VCC V IIHH Input High Current Vin = Vcc 200 µA IIMM Input MID Current Vin = Vcc/2 –50 50 µA Input LOW Current Vin = GND Differential CML Serial Outputs: OUTA±, OUTB±, OUTC±, OUTD± –200 µA Typ. Max. Unit 100Ω differential load VCC – 0.5 VCC – 0.2 V 150Ω differential load VCC – 0.5 VCC – 0.2 V IILL VOHC Output HIGH Voltage Notes: 16. Tested one output at a time, output shorted for less than one second, less than 10% duty cycle. 17. This is the minimum difference in voltage between the true and complement inputs required to ensure detection of a logic-1 or logic-0. A logic-1 exists when the true (+) input is more positive than the complement (–) input. A logic-0 exists when the complement (-) input is more positive than true (+) input. 18. The common mode range defines the allowable range of REFCLK+ and REFCLK– when REFCLK+ = REFCLK–. This marks the zero-crossing between the true and complement inputs as the signal switches between a logic-1 and a logic-0. Document #: 38-02057 Rev. *G Page 20 of 29 CYP15G0402DXB CYV15G0402DXB CYP(V)15G0402DXB DC Electrical Characteristics Over the Operating Range (continued) Parameter Description VOLC Test Conditions Output LOW Voltage VODIF Output Differential Voltage |(OUT+) – (OUT–)| Min. Max. Unit 100Ω differential load VCC – 1.1 VCC – 0.7 V 150Ω differential load VCC – 1.1 VCC – 0.7 V 100Ω differential load 450 900 mV 150Ω differential load 560 1000 mV 100 1200 mV VCC V Differential Serial Line Receiver Inputs: INA±, INB±, INC±, IND± VDIFFS[17] Input Differential Voltage |(IN+) – (IN-)| VIHE Highest Input HIGH Voltage VILE Lowest Input LOW Voltage IIHE Input HIGH Current VIN = VIHH Max. IILE Input LOW Current VIN = VILL Min. VCOM [19, 20] VCC – 2.0 1350 –700 Common mode input range ICC Power Supply Current REFCLK = Max. Commercial Power Supply Current REFCLK = 125 MHz Commercial mA mA VCC − 1.95 VCC − 0.05 V Typ.[22] Max.[21] Unit 870 1060 mA 1100 mA 1060 mA 1100 mA Power Supply ICC V Industrial 830 Industrial Test Loads and Waveforms 3.3V RL = 100Ω R1 R1 = 590Ω R2 = 435Ω CL CL ≤ 7 pF (Includes fixture and probe capacitance) R2 (a) LVTTL Output Test Load (b) CML Output Test Load GND 2.0V 0.8V 2.0V 0.8V Note 23 Note 23 3.0V Vth = 1.4V RL VIHE VIHE Vth = 1.4V ≤ 1 ns VILE ≤ 1 ns (c) LVTTL Input Test Waveform Note 24 80% 80% 20% ≤ 270 ps 20% VILE ≤ 270 ps (d) CML/LVPECL Input Test Waveform Notes: 19. The common mode range defines the allowable range of INPUT+ and INPUT– when INPUT+ = INPUT–. This marks the zero-crossing between the true and complement inputs as the signal switches between a logic-1 and a logic-0. 20. Not applicable for AC-coupled interfaces. For AC-coupled interfaces, VDIFFS requirement still needs to be satisfied. 21. Maximum ICC is measured with VCC = MAX, parallel outputs unloaded, RX channels enabled, and Serial Line Drivers enabled and sending a continuous alternating 01 pattern to the associated receive channel. 22. Typical ICC is measured under similar conditions except with VCC = 3.3V, TA = 25°C, parallel outputs unloaded, RX channels enabled, and Serial Line Drivers enabled and sending a continuous alternating 01 pattern to the associated receive channel. 23. Cypress uses constant current (ATE) load configurations and forcing functions. This figure is for reference only. 5-pF differential load reflects tester capacitance, and is recommended at low data rates only. 24. The LVTTL switching threshold is 1.4V. All timing references are made relative to the point where the signal edges crosses the threshold voltage. Document #: 38-02057 Rev. *G Page 21 of 29 CYP15G0402DXB CYV15G0402DXB CYP(V)15G0402DXB AC Characteristics Over the Operating Range CYP(V)15G0402DXB Transmitter LVTTL Switching Characteristics Over the Operating Range Min. Max. Unit fTS Parameter TXCLKx Clock Frequency 19.5 150 MHz tTXCLK TXCLKx Period 6.66 51.28 ns tTXCLKH [25] TXCLKx HIGH Time 2.2 [25] TXCLKx LOW Time 2.2 TXCLKx Rise Time 0.2 1.7 ns 1.7 ns tTXCLKL tTXCLKR [25, 26, 27] tTXCLKF [25, 26, 27] Description ns ns TXCLKx Fall Time 0.2 tTXDS Transmit Data Set-up Time to TXCLKx↑ (TXCKSEL ≠ LOW) 1.7 tTXDH Transmit Data Hold Time from TXCLKx↑ (TXCKSEL ≠ LOW) 0.8 fTOS TXCLKO Clock Frequency = 1x or 2x REFCLK Frequency 19.5 150 MHz tTXCLKO TXCLKO Period 6.66 51.28 ns tTXCLKOD+ TXCLKO+ Duty Cycle with 60% HIGH time –1.0 +0.5 ns tTXCLKOD– TXCLKO– Duty Cycle with 40% HIGH time –0.5 +1.0 ns Min. Max. Unit ns ns CYP(V)15G0402DXB Receiver LVTTL Switching Characteristics Over the Operating Range Parameter Description fRS RXCLKx Clock Output Frequency 9.75 150 MHz tRXCLKP RXCLKx Period 6.66 102.56 ns RXCLKx HIGH Time (RXRATE = LOW) 2.33[25] 26.64 ns RXCLKx HIGH Time (RXRATE = HIGH) 5.66 52.28 ns RXCLKx LOW Time (RXRATE = LOW) 2.33[25] 26.64 ns RXCLKx LOW Time (RXRATE = HIGH) 5.66 52.28 ns tRXCLKD RXCLKx Duty Cycle centered at 50% –1.0 +1.0 ns tRXCLKR [25] RXCLKx Rise Time 0.3 1.2 ns 0.3 1.2 tRXCLKH tRXCLKL tRXCLKF [25] tRXDV– [28] tRXDV+ [28] RXCLKx Fall Time ns Status and Data Valid Time to RXCLKx 5UI – 1.5 ns Status and Data Valid Time to RXCLKx (HALF RATE RECOVERED CLOCK) 5UI – 1.0 ns Status and Data Valid Time from RXCLKx 5UI – 1.8 ns Status and Data Valid Time from RXCLKx (HALF RATE RECOVERED CLOCK) 5UI – 2.3 ns CYP(V)15G0402DXB REFCLK Switching Characteristics Over the Operating Range Parameter Description Min. Max. Unit 19.5 150 MHz REFCLK Period 6.6 51.28 REFCLK HIGH Time (TXRATE = HIGH) 5.9 REFCLK HIGH Time (TXRATE = LOW) 2.9[25] ns REFCLK LOW Time (TXRATE = HIGH) 5.9 ns REFCLK LOW Time (TXRATE = LOW) 2.9[25] ns fREF REFCLK Clock Frequency tREFCLK tREFH tREFL ns ns Notes: 25. Tested initially and after any design or process changes that may affect these parameters, but not 100% tested. 26. The ratio of rise time to falling time must not vary by greater than 2:1. 27. For a given operating frequency, neither rise or fall specification can be greater than 20% of the clock-cycle period or the data sheet maximum time. 28. Parallel data output specifications are only valid if all inputs or outputs are loaded with similar DC and AC loads. Document #: 38-02057 Rev. *G Page 22 of 29 CYP15G0402DXB CYV15G0402DXB CYP(V)15G0402DXB REFCLK Switching Characteristics Over the Operating Range (continued) Parameter tREFD [29] tREFR [25, 26, 27] Description REFCLK Duty Cycle Min. Max. Unit 30 70 % REFCLK Rise Time (20% – 80%) 2 ns tREFF [25, 26, 27] REFCLK Fall Time (20% – 80%) 2 ns tTREFDS Transmit Data Setup Time to REFCLK (TXCKSEL = LOW) 1.7 ns tTREFDH Transmit Data Hold Time from REFCLK (TXCKSEL = LOW) 0.8 ns REFCLK Frequency Referenced to Received Clock Period -1500 tREFRX [8] +1500 ppm Min. Max. Unit CYP(V)15G0402DXB Transmit Serial Outputs and TX PLL Characteristics Over the Operating Range Parameter Description Condition tB Bit Time tRISE [25] CML Output Rise Time 20% – 80% (CML Test Load) tFALL [25] tDJ [25, 30, 32] tRJ [25, 31, 32] tTXLOCK 5100 660 ps SPDSEL = HIGH 50 270 ps SPDSEL = MID 100 500 ps SPDSEL = LOW 180 1000 ps CML Output Fall Time 80% – 20% (CML Test Load) SPDSEL = HIGH 50 270 ps SPDSEL = MID 100 500 ps SPDSEL = LOW 180 1000 ps 25 ps Deterministic Jitter (peak-peak) IEEE 802.3z Random Jitter (σ) IEEE 802.3z Transmit PLL lock to REFCLK 11 ps 200 us 376K UI[33] 376K UI CYP(V)15G0402DXB Receive Serial Inputs and CDR PLL Characteristics Over the Operating Range tRXLOCK Receive PLL lock to input data stream (cold start) Receive PLL lock to input data stream tRXUNLOCK Receive PLL Unlock Rate tJTOL Total Jitter Tolerance IEEE 802.3z 600 ps tDJTOL Deterministic Jitter Tolerance IEEE 802.3z 370 ps 46 UI Capacitance [25] Parameter Description Test Conditions Max. Unit CINTTL TTL Input Capacitance TA = 25°C, f0 = 1 MHz, VCC = 3.3V 7 pF CINPECL PECL input Capacitance TA = 25°C, f0 = 1 MHz, VCC = 3.3V 4 pF Notes: 29. The duty cycle specification is a simultaneous condition with the tREFH and tREFL parameters. This means that at faster character rates the REFCLK duty cycle cannot be as large as 30% – 70%. 30. While sending continuous K28.5s, outputs loaded to a balanced 100Ω load, measured at the cross point of differential outputs, over the operating range. 31. While sending continuous K28.7s, after 100,000 samples measured at the cross point of differential outputs, time referenced to REFCLK input, over the operating range. 32. Total jitter is calculated at an assumed BER of 1E −12. Hence: total jitter (tJ) = (tRJ * 14) + tDJ. 33. Receiver UI (Unit Interval) is calculated as 1 / (fREF * 20) (when RXRATE = HIGH) or 1 / (fREF * 10) (when RXRATE = LOW) if no data is being received, or 1 / (fREF * 20) (when RXRATE = HIGH) or 1 / (fREF * 10) (when RXRATE = LOW) of the remote transmitter if data is being received. In an operating link this is equivalent to tB. Document #: 38-02057 Rev. *G Page 23 of 29 CYP15G0402DXB CYV15G0402DXB CYP(V)15G0402DXB HOTLink II Transmitter Switching Waveforms Transmit Interface Write Timing TXCKSEL ≠ LOW tTXCLK tTXCLKH tTXCLKL TXCLKx tTXDS TXDx[9:0], TXOPx tTXDH Transmit Interface Write Timing TXCKSEL = LOW TXRATE = LOW tREFCLK tREFH tREFL REFCLK tTREFDS TXDx[9:0], TXOPx tTREFDH Transmit Interface Write Timing TXCKSEL = LOW TXRATE = HIGH tREFCLK tREFH tREFL Note 34 REFCLK Note 34 tTREFDS tTREFDS TXDx[9:0], TXOPx, tTREFDH tTREFDH Transmit Interface TXCLKO Timing TXCKSEL = LOW TXRATE = HIGH tREFCLK tREFH tREFL REFCLK Note 36 tTXCLKO tTXCLKOD+ tTXCLKOD– Note 35 TXCLKO Notes: 34. When REFCLK is configured for half-rate operation (TXRATE = HIGH) and data is captured using REFCLK instead of a TXCLKx clock (TXCKSEL = LOW), data is captured using both the rising and falling edges of REFCLK. 35. The TXCLKO output is at twice the rate of REFCLK when TXRATE = HIGH and same rate as REFCLK when TXRATE = LOW. TXCLKO does not follow the duty cycle of REFCLK. 36. The rising edge of TXCLKO output has no direct phase relationship to the REFCLK input. Document #: 38-02057 Rev. *G Page 24 of 29 CYP15G0402DXB CYV15G0402DXB CYP(V)15G0402DXB HOTLink II Transmitter Switching Waveforms (continued) Transmit Interface TXCLKO Timing TXCKSEL = LOW TXRATE = LOW tREFCLK tREFH tREFL Note 35 REFCLK tTXCLKO Note 36 tTXCLKOD+ tTXCLKOD– TXCLKO Switching Waveforms for the CYP(V)15G0402DXB HOTLink II Receiver Receive Interface Read Timing RXRATE = LOW tRXCLKP tRXCLKH tRXCLKL RXCLKx+ RXCLKx– tRXDV– RXDx[9:0], COMDETx RXOPx tRXDV+ Receive Interface Read Timing RXRATE = HIGH tRXCLKP tRXCLKH tRXCLKL RXCLKx+ RXCLKx– tRXDV– RXDx[9:0], COMDETx], RXOPx tRXDV+ Document #: 38-02057 Rev. *G Page 25 of 29 CYP15G0402DXB CYV15G0402DXB Table 9. Package Coordinate Signal Allocation Ball ID Signal Name Signal Type Ball ID Signal Name Signal Type Ball ID Signal Name Signal Type A01 INC– CML IN C04 LPENB LVTTL IN E19 VCC POWER A02 OUTC– CML OUT C05 VCC POWER E20 VCC POWER A03 N/C NO CONNECT C06 PARCTL 3-LEVEL SEL F01 TXPERC LVTTL OUT A04 N/C NO CONNECT C07 SDASEL 3-LEVEL SEL F02 TXOPC LVTTL IN PU A05 VCC POWER C08 GND GROUND F03 TXDC[0] LVTTL IN A06 IND– CML IN C09 BOE[7] LVTTL IN PU F04 N/C NO CONNECT A07 OUTD– CML OUT C10 BOE[5] LVTTL IN PU F17 BISTLE LVTTL IN PU A08 GND GROUND C11 BOE[3] LVTTL IN PU F18 RXDB[0] LVTTL OUT A09 N/C NO CONNECT C12 BOE[1] LVTTL IN PU F19 RXOPB LVTTL 3-S OUT A10 N/C CML OUT C13 GND GROUND F20 RXDB[1] LVTTL OUT A11 INA– CML IN C14 GND GROUND G01 TXDC[7] LVTTL IN A12 OUTA– CML OUT C15 GND GROUND G02 TXCKSEL 3-LEVEL SEL A13 GND GROUND C16 VCC POWER G03 TXDC[4] LVTTL IN A14 N/C NO CONNECT C17 TXRATE LVTTL IN PD G04 TXDC[1] LVTTL IN A15 N/C NO CONNECT C18 RXRATE LVTTL IN PD G17 GND GROUND A16 VCC POWER C19 N/C NO CONNECT G18 OELE LVTTL IN PU A17 INB– CML IN C20 TDO LVTTL 3-S OUT G19 FRAMCHAR 3-LEVEL SEL A18 OUTB– CML OUT D01 TCLK LVTTL IN PD G20 RXDB[3] LVTTL OUT A19 N/C NO CONNECT D02 TRSTZ LVTTL IN PU H01 GND GROUND A20 N/C NO CONNECT D03 LPEND LVTTL IN H02 GND GROUND B01 INC+ CML IN D04 LPENA LVTTL IN H03 GND GROUND B02 OUTC+ CML OUT D05 VCC POWER H04 GND GROUND B03 N/C NO CONNECT D06 RFMODE 3-LEVEL SEL H17 GND GROUND B04 N/C NO CONNECT D07 SPDSEL 3-LEVEL SEL H18 GND GROUND B05 VCC POWER D08 GND GROUND H19 GND GROUND B06 IND+ CML IN D09 BOE[6] LVTTL IN PU H20 GND GROUND B07 OUTD+ CML OUT D10 BOE[4] LVTTL IN PU J01 TXDC[9] LVTTL IN B08 GND GROUND D11 BOE[2] LVTTL IN PU J02 TXDC[5] LVTTL IN B09 N/C NO CONNECT D12 BOE[0] LVTTL IN PU J03 TXDC[2] LVTTL IN B10 N/C NO CONNECT D13 GND GROUND J04 TXDC[3] LVTTL IN B11 INA+ CML IN D14 GND GROUND J17 COMDETB LVTTL OUT B12 OUTA+ CML OUT D15 GND GROUND J18 RXDB[2] LVTTL OUT B13 GND GROUND D16 VCC POWER J19 RXDB[7] LVTTL OUT B14 N/C NO CONNECT D17 N/C NO CONNECT J20 RXDB[4] LVTTL OUT B15 N/C NO CONNECT D18 RXLE LVTTL IN PU K01 RXDC[4] LVTTL OUT B16 VCC POWER D19 N/C NO CONNECT K02 RXCLKC– LVTTL OUT B17 INB+ CML IN D20 N/C NO CONNECT K03 TXDC[8] LVTTL IN B18 OUTB+ CML OUT E01 VCC POWER K04 LFIC LVTTL OUT B19 N/C NO CONNECT E02 VCC POWER K17 RXDB[5] LVTTL OUT B20 N/C NO CONNECT E03 VCC POWER K18 RXDB[6] LVTTL OUT C01 TDI LVTTL IN PU E04 VCC POWER K19 RXDB[9] LVTTL OUT C02 TMS LVTTL IN PU E17 VCC POWER K20 RXCLKB+ LVTTL I/O PD C03 LPENC LVTTL IN E18 VCC POWER L01 RXDC[5] LVTTL OUT Document #: 38-02057 Rev. *G Page 26 of 29 CYP15G0402DXB CYV15G0402DXB Table 9. Package Coordinate Signal Allocation (continued) Ball ID Signal Name Signal Type Ball ID Signal Name Signal Type Ball ID Signal Name Signal Type L02 RXCLKC+ LVTTL I/O PD T17 VCC POWER V20 RXDA[1] LVTTL OUT L03 TXCLKC LVTTL IN PD T18 VCC POWER W01 TXDD[5] LVTTL IN L04 TXDC[6] LVTTL IN T19 VCC POWER W02 TXDD[7] LVTTL IN L17 RXDB[8] LVTTL OUT T20 VCC POWER W03 LFID LVTTL OUT L18 LFIB LVTTL OUT U01 TXDD[0] LVTTL IN W04 RXCLKD– LVTTL OUT L19 RXCLKB– LVTTL OUT U02 TXDD[1] LVTTL IN W05 VCC POWER L20 TXDB[6] LVTTL IN U03 TXDD[2] LVTTL IN W06 RXDD[6] LVTTL OUT M01 RXDC[6] LVTTL OUT U04 TXDD[9] LVTTL IN W07 RXDD[0] LVTTL OUT M02 RXDC[7] LVTTL OUT U05 VCC POWER W08 GND GROUND M03 RXDC[9] LVTTL OUT U06 RXDD[4] LVTTL OUT W09 TXCLKO– LVTTL OUT M04 RXDC[8] LVTTL OUT U07 RXDD[3] LVTTL OUT W10 TXRST LVTTL IN PU M17 TXDB[9] LVTTL IN U08 GND GROUND W11 TXOPA LVTTL IN PU M18 TXDB[8] LVTTL IN U09 RXOPD LVTTL 3-S OUT W12 RFENA LVTTL IN PD M19 TXDB[7] LVTTL IN U10 RFENC LVTTL IN PD W13 GND GROUND M20 TXCLKB LVTTL IN PD U11 REFCLK– PECL IN W14 TXDA[2] LVTTL IN N01 GND GROUND U12 TXDA[1] LVTTL IN W15 TXDA[6] LVTTL IN N02 GND GROUND U13 GND GROUND W16 VCC POWER N03 GND GROUND U14 TXDA[4] LVTTL IN W17 LFIA LVTTL OUT N04 GND GROUND U15 TXDA[8] LVTTL IN W18 RXCLKA– LVTTL OUT N17 GND GROUND U16 VCC POWER W19 RXDA[6] LVTTL OUT N18 GND GROUND U17 RXDA[4] LVTTL OUT W20 RXDA[3] LVTTL OUT N19 GND GROUND U18 RXOPA LVTTL OUT Y01 TXDD[6] LVTTL IN N20 GND GROUND U19 COMDETA LVTTL OUT Y02 TXCLKD LVTTL IN P01 RXDC[3] LVTTL OUT U20 RXDA[0] LVTTL OUT Y03 RXDD[9] LVTTL OUT P02 RXDC[2] LVTTL OUT V01 TXDD[3] LVTTL IN Y04 RXCLKD+ LVTTL I/O PD P03 RXDC[1] LVTTL OUT V02 TXDD[4] LVTTL IN Y05 VCC POWER P04 RXDC[0] LVTTL OUT V03 TXDD[8] LVTTL IN Y06 RXDD[7] LVTTL OUT P17 TXDB[5] LVTTL IN V04 RXDD[8] LVTTL OUT Y07 RXDD[2] LVTTL OUT P18 TXDB[4] LVTTL IN V05 VCC POWER Y08 GND GROUND P19 TXDB[3] LVTTL IN V06 RXDD[5] LVTTL OUT Y09 TXCLKO+ LVTTL OUT P20 TXDB[2] LVTTL IN V07 RXDD[1] LVTTL OUT Y10 N/C NO CONNECT R01 COMDETC LVTTL OUT V08 GND GROUND Y11 TXCLKA LVTTL IN PD R02 RXOPC LVTTL 3-S OUT V09 COMDETD LVTTL OUT Y12 TXPERA LVTTL OUT R03 TXPERD LVTTL OUT V10 RFEND LVTTL IN PD Y13 GND GROUND R04 TXOPD LVTTL IN PU V11 REFCLK+ PECL IN Y14 TXDA[0] LVTTL IN R17 TXDB[1] LVTTL IN V12 RFENB LVTTL IN PD Y15 TXDA[5] LVTTL IN R18 TXDB[0] LVTTL IN V13 GND GROUND Y16 VCC POWER R19 TXOPB LVTTL IN PU V14 TXDA[3] LVTTL IN Y17 TXDA[9] LVTTL IN R20 TXPERB LVTTL OUT V15 TXDA[7] LVTTL IN Y18 RXCLKA+ LVTTL I/O PD T01 VCC POWER V16 VCC POWER Y19 RXDA[8] LVTTL OUT T02 VCC POWER V17 RXDA[9] LVTTL OUT Y20 RXDA[7] LVTTL OUT T03 VCC POWER V18 RXDA[5] LVTTL OUT T04 VCC POWER V19 RXDA[2] LVTTL OUT Document #: 38-02057 Rev. *G Page 27 of 29 CYP15G0402DXB CYV15G0402DXB Ordering Information Speed Package Name Ordering Code Operating Range Package Type Standard CYP15G0402DXB-BGC BL256 256-ball Thermally Enhanced Ball Grid Array Commercial Standard CYP15G0402DXB-BGI BL256 256-ball Thermally Enhanced Ball Grid Array Industrial Standard CYV15G0402DXB-BGC BL256 256-ball Thermally Enhanced Ball Grid Array Commercial Standard CYV15G0402DXB-BGI BL256 256-ball Thermally Enhanced Ball Grid Array Industrial Standard CYP15G0402DXB-BGXC BL256 Pb-Free 256-ball Thermally Enhanced Ball Grid Array Commercial Standard CYP15G0402DXB-BGXI BL256 Pb-Free 256-ball Thermally Enhanced Ball Grid Array Industrial Standard CYV15G0402DXB-BGXC BL256 Pb-Free 256-ball Thermally Enhanced Ball Grid Array Commercial Standard CYV15G0402DXB-BGXI BL256 Pb-Free 256-ball Thermally Enhanced Ball Grid Array Industrial Package Diagram 256-lead L2 Ball Grid Array (27 x 27 x 1.57 mm) BL256 51-85123-*E HOTLink is a registered trademark, and HOTLink II and MultiFrame are trademarks, of Cypress Semiconductor Corporation. ESCON is a registered trademark of International Business Machines. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-02057 Rev. *G Page 28 of 29 © Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CYP15G0402DXB CYV15G0402DXB Document History Page Document Title:CYP(V)15G0402DXB Quad HOTLink II™ SERDES Document Number: 38-02057 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 116285 07/16/02 SDR New Data Sheet *A 118985 09/30/02 LNM Changed TXCLKO description Changed TXPERx description introduced SMPTE pathological test clause Removed the LOW setting for FRAMCHAR and related references Changed VODIF and VOLC for CML output Changed the IOST boundary values Changed the tTXCLKR and tTXCLKF min values Changed tTXDS and tTXDH and tTREFDS and tTREFDH Changed tREFADV– and tREFCDV– and tREFCDV+ Changed the JTAG ID from 0C801069 to 1C801069 *B 122545 12/09/02 CGX Changed Minimum tRISE/tFALL for CML Changed tTXCLKOD+, tTXCLKOD- for LVTTL Changed tRXLOCK Changed tDJ, tRJ Changed tJTOL Changed tTXLOCK Changed tRXCLKH, tRXCLKL Changed Power Specs Changed verbiage...Paragraph: Clock/Data Recovery Changed verbiage...Paragraph: Range Control Updated differences to pin configuration and pin table Added Power-up Requirements *C 122211 12/28/02 RBI Minor change Document Control corrected Document History Page *D 124992 04/15/03 POT Changed CYP15G0402DXB to CYP(V)15G0402DXB type corresponding to Video-compliant parts Reduced the lower limit of the serial signaling rate from 200 Mbaud to 195 Mbaud and changed the associated specifications accordingly *E 128367 07/24/03 PDS Added tRXDV+ timing parameter Removed irrelevant timing parameters *F 131899 01/21/04 PDS When TXCKSEL = MID or HIGH, TXRATE = HIGH is an invalid mode. Made appropriate changes to reflect this invalid condition Changed LFIx to Asynchronous output Expanded the CDR Range Controller’s permissible frequency offset between incoming serial signaling rate and Reference clock from ±200-PPM to ±1500-PPM (changed parameter tREFRX) Revised Typical Power numbers to match final characterization data *G 338721 See ECN SUA Added Pb-Free Package option availability Changed MBd to MBaud in SPDSEL pin description Document #: 38-02057 Rev. *G Page 29 of 29