DI200~DI2010 DUAL-IN-LINE GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 50~1000 Volts CURRENT DIP 2.0 Amperes Unit : inch (mm) FEATURES • Plastic material used carries Underwriters Laboratory recognition 94V-O .335(8.51) .316(8.05) • Low leakage • Exceeds environmental standards of MIL-S-19500/228 .350(8.9) .300(7.6) • Ideal for printed circuit board .255(6.5) .245(6.2) .315(8.00) .285(7.24) • Surge overload rating-- 50 amperes peak .130(3.30) .120(3.05) • In compliance with EU RoHS 2002/95/EC directives MECHANICALDATA • Case: Reliable low cost construction utilizing molded plastic technique .045(1.14) .035(0.89) results in inexpensive product .022(0.56) • Terminals: Lead solderable per MIL-STD-750, Method 2026 .018(0.46) .185(4.69) .150(3.81) • Polarity: Polarity symbols molded or marking on body • Mounting Position: Any • Weight: 0.0115 ounce, 0.3268 gram .075(1.90) .205(5.2) .195(5.0) .055(1.39) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified.Single phase, half wave, 60Hz, Resistive or inductive load. For capacitive load, derate current by 20% PA RA ME TE R S YMB OL D I2 0 0 D I2 0 1 D I2 0 2 D I2 0 4 D I2 0 6 D I2 0 8 D I2 0 1 0 UNITS Ma xi mum Re curre nt P e a k Re ve rse Vo lta g e V RRM 50 10 0 200 400 600 800 1000 V Ma xi mum RMS B ri d ge Inp ut Vo lta g e V RMS 35 70 140 28 0 420 560 700 V Ma xi mum D C B lo c ki ng Vo lta g e V DC 50 10 0 200 400 600 800 1000 V Ma xi mum A ve ra g e F o rwa rd C urre nt T A =4 0 O C IF (AV ) 2 .0 A P e a k F o rwa rd S urg e C urrent:8 .3 ms si ng le ha lf s i ne -wa ve sup e ri mp o se d o n ra te d lo ad (JE D E C me tho d ) IF S M 50 A I2 t Ra ti ng fo r fus i ng ( t<8 .3 5 ms ) I2 t 1 0 .0 A 2S Ma xi mum F o rwa rd Vo lta g e D ro p p e r B ri d g e E le me nt a t 2 .0 A VF 1 .1 V Ma xi mum D C Re verse C urre ntT J =2 5 O C a t Ra te d D C B lo cki ng Vo lta g eT J =1 2 5 O C IR 5 .0 500 μA Typ i ca l Junc ti o n ca p a c i ta nc e (No te 1 ) CJ 25 pF R θJ A R θJL 40 15 T J ,T s TG -5 5 to + 1 5 0 Typ i ca l the rma l re si s ta nc e p e r le g ((No te 2 ) Op e ra ti ng J unsti o n a nd S to ra g e Te mp e ra ture Ra ng e O C / W O C NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts 2. Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.5 X 0.5"(13 X 13mm) copper pads REV.0.0-NOV.05.2009 PAGE . 1 DI200~DI2010 3.0 2.5 2.0 1.5 1.0 0.5 0 0 50 100 150 INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES 10 O TA = 100 C 1.0 0.1 TA= 25 O C 20 40 60 80 100 120 140 PERCENT OF PEAK REVERSE VOLTAGE, % FIG.3 TYPICAL REVERSE CHARACTERISTICS REV.0.0-NOV.05.2009 .1 .01 0 0.2 0.4 0.8 0.6 1.0 1.2 1.4 Fig.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FORWARD SURGE CURRENT,AMPERES pk (HALF SINE-WAVE) INSTANTANEOUS REVERSE CURRENT,uA FIG.1 DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 0 1.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS AMBIENT TEMPERATURE, OC 0.01 10 70 60 50 40 30 20 10 0 1 2 5 10 20 40 60 100 NO. OF CYCLES AT 60Hz Fig.4 MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PAGE . 2