ETC DRM057

Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Open Loop Universal
Motor Chopper
Based on the
MC68HC908QT4
Microcontroller
Reference Design
M68HC08
Microcontrollers
Designer Reference
Manual
DRM057
Rev. 0, 1/2004
MOTOROLA.COM/SEMICONDUCTORS
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Open Loop Universal Motor
Chopper Based on the
MC68HC908QT4
Microcontroller
Designer Reference Manual — Rev 0
by: Ladislav Makovic
Motorola Ltd.
Roznov pod Radhostem
WARNING:
This circuit is powered directly from the mains. It is dangerous to
touch any part of the circuit, even if a 0% duty cycle is generated.
Do not connect any computer, oscilloscope or development
system to this circuit without using an isolation transformer.
Motorola and the Motorola logo are registered trademarks of Motorola,
Inc.
CodeWarrior® is a registered trademark of MetroWerks, a wholly owned
subsidiary of Motorola, Inc.
DRM057 — Rev 0
Designer Reference Manual
MOTOROLA
3
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Revision history
To provide the most up-to-date information, the revision of our
documents on the World Wide Web will be the most current. Your printed
copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://www.motorola.com/semiconductors
Freescale Semiconductor, Inc...
The following revision history table summarizes changes contained in
this document. For your convenience, the page number designators
have been linked to the appropriate location.
Revision history
Date
Revision
Level
1/2004
0
Description
Initial release
Designer Reference Manual
Page
Number(s)
N/A
DRM057 — Rev 0
4
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Designer Reference Manual — Chopper using MC68HC908QT4
Table of Contents
Freescale Semiconductor, Inc...
Section 1. Introduction
1.1
Overview of the Application . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
1.2
Intended Functionality of the Application . . . . . . . . . . . . . . . . . 11
1.3
Benefits of Our Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.4
The MC68HC908QT4 Microcontroller . . . . . . . . . . . . . . . . . . .12
1.5
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Section 2. Initial Design Conditions
2.1
System Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . 15
2.2
System Software Requirements . . . . . . . . . . . . . . . . . . . . . . . .15
Section 3. Hardware Design
3.1
Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.3
PCB Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Section 4. Software Design
4.1
Basic Software Description. . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4.2
Constant and Variable Definitions . . . . . . . . . . . . . . . . . . . . . . 25
4.3
Flow Chart Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.4
Microcontroller Resource Usage . . . . . . . . . . . . . . . . . . . . . . . 35
Section 5. System Setup
DRM057 — Rev 0
Designer Reference Manual
MOTOROLA
5
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
5.1
Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.2
Software Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
5.3
Required Software Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.4
Building and Uploading the Application . . . . . . . . . . . . . . . . . .38
5.5
Executing the Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Freescale Semiconductor, Inc...
Appendix A. Abbreviations and Definitions
Designer Reference Manual
DRM057 — Rev 0
6
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Designer Reference Manual — Chopper using MC68HC908QT4
List of Figures
Figure
Freescale Semiconductor, Inc...
1-1
1-2
3-1
3-2
3-3
3-4
4-1
4-2
4-3
Title
Page
The Open Loop PWM Chopper . . . . . . . . . . . . . . . . . . . . . . . .10
The Pulse Width Modulation ‘Chopper’ Technique. . . . . . . . . .11
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Circuit Schematic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
PCB — Track Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PCB — Component Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Main Program Flow Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Interrupt Subroutine Flow Charts . . . . . . . . . . . . . . . . . . . . . . . 25
PWM Setup for 3.2 MHz Bus Frequency . . . . . . . . . . . . . . . . . 33
DRM057 — Rev 0
Designer Reference Manual
MOTOROLA
7
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
List of Tables
List of Tables
Table
Freescale Semiconductor, Inc...
3-1
4-1
4-2
Title
Page
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Memory Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
I/O Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Designer Reference Manual
DRM057 — Rev 0
8
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Designer Reference Manual — Chopper using MC68HC908QT4
Section 1. Introduction
This reference manual describes a real application, which can be used
in a low-cost product. Using a microcontroller allows the system to be
software programmable by changing defined constants within the
application software. Another advantage of using a microcontroller is
that the control algorithm can be changed simply, by re-programming the
microcontroller with new firmware. The unused memory and some
performance capacity remain available for other purposes. These facts
make this application particularly suitable for the appliance market.
1.1 Overview of the Application
The application presents a low-cost, open loop universal motor chopper
control drive system based on the MC68HC908QT4 microcontroller. A
PWM (pulse width modulation) technique is used to adjust the voltage
applied to the motor. Modulation of the PWM's duty cycle allows the
average value of the voltage applied to the motor to be varied.
Compared to a phase angle drive, the chopper drive requires a more
complicated power stage, with an input power rectifier, a power switch,
and a power fast diode. The advantage of the chopper drive is higher
efficiency, with less acoustic noise and better EMC behavior.
1.1.1 Uses of the Application
•
Washing machines
•
Vacuum cleaners
•
Hand tools
•
Food processors
•
Dishwashers
•
Single-phase variable-speed drives
•
Low-cost, medium-power applications with variable voltage output
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Introduction
For More Information On This Product,
Go to: www.freescale.com
9
Freescale Semiconductor, Inc.
Introduction
Freescale Semiconductor, Inc...
1.1.2 Features
•
Capable of supplying universal/DC motors
•
Variable output voltage 0-230 V AC rms with defined step and
delay ramp
•
Maximum output current 6.52 A AC rms (1500 W, 230 V) (short
time peak current 8 A)
•
Uses PWM technique to modulate output voltage (5.882 kHz
switching frequency)
•
Capable of supplying general DC inductive/resistive loads
•
Electronic switch on/off PWM generation
•
Easy to re-program the system behavior
Figure 1-1. The Open Loop PWM Chopper
Designer Reference Manual
10
DRM057 — Rev 0
Introduction
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Introduction
Intended Functionality of the Application
1.2 Intended Functionality of the Application
Freescale Semiconductor, Inc...
This reference manual describes the design of a low-cost chopper motor
control drive system based on the MC68HC908QT4 microcontroller, an
IGBT (Insulated Gate Bipolar Transistor), and an ultra-fast high voltage
(freewheeling) diode. This low-cost single-phase power board is
dedicated to universal brushed motors. The universal motor is the most
widely used motor in home appliances, such as vacuum cleaners,
washers, hand tools, and food processors. The operational mode used
in this application is open loop and regulated input motor voltage. The
type of motor and its drive have a high impact on many home appliance
features, such as cost, size, noise and efficiency. Electronic control
usually becomes necessary when variable speed or energy savings are
required.
Motor Voltage
50% duty cycle
DC Voltage
Gate Signal
Figure 1-2. The Pulse Width Modulation ‘Chopper’ Technique
Microcontrollers offer the advantages of low cost and attractive design.
They can operate with only a few external components, reducing the
energy consumption as well as the cost. This circuit was designed as a
very simple schematic, using all the features of a simple microcontroller.
The microcontroller and this circuit scheme may be used in a wide
variety of applications.
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Introduction
For More Information On This Product,
Go to: www.freescale.com
11
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Introduction
The Pulse Width Modulation technique (PWM) is used to adjust the
voltage applied to the motor (Figure 1-2). Modulation of the PWM’s duty
cycle allows variation of the average voltage value seen by the motor.
This PWM technique is often termed ‘chopper’, because of the chopped
drive signal that is created.
This document also explains how to design the software implementation
using an M68HC08 family microcontroller. A low-cost microcontroller
such as this is powerful enough to handle the workload necessary for
driving a closed loop chopper drive.
1.3 Benefits of Our Solution
Compared to a poorer analog solution, a microcontroller based drive
exhibits many advantages. Some of these are listed below.
•
Choice of different control algorithms
•
Choice of any shape of speed command (acceleration and
deceleration phase)
•
Easy adaptation to a closed loop control algorithm
•
Software can simplify the hardware
•
Diagnostic functions
•
Open for innovation
1.4 The MC68HC908QT4 Microcontroller
The MC68HC908QT4 is a member of the low-cost, high-performance
M68HC08 Family of 8-bit microcontroller units (MCUs). The M68HC08
family is a Complex Instruction Set Computer (CISC), with a Von
Neumann architecture. All MCUs in the family use the enhanced
M68HC08 central processor unit (CPU08), and are available with a
variety of modules, memory sizes and types, and package types.
Designer Reference Manual
12
DRM057 — Rev 0
Introduction
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Introduction
References
Some key features of the MC68HC908QT4 are listed below.
•
4K bytes of in-application re-programmable FLASH and 128 bytes
of RAM
•
2-channel, 16-bit timer with selectable input capture, output
compare, and PWM
•
High-performance, easy-to-use M68HC08 CPU
•
Trimmable internal oscillator with ± 5% accuracy
•
4-channel, 8-bit analog to digital converter
•
Selectable trip point low voltage inhibit (LVI)
•
Computer operating properly (COP) timer with auto wake-up from
STOP
•
Flexible high-current I/O and keyboard interrupts
•
Five bidirectional I/O pins and one input-only pin
•
Available in 8-pin DIP or SOIC packages
1.5 References
1. PWM_setup.xls - placed into project [2] sources.
2. UM_Chopper.mcp - project, debugged under CodeWarrior CW08
V3.0.
3. Schematic, PCB.
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Introduction
For More Information On This Product,
Go to: www.freescale.com
13
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Introduction
Designer Reference Manual
14
DRM057 — Rev 0
Introduction
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Designer Reference Manual — Chopper using MC68HC908QT4
Section 2. Initial Design Conditions
This section deals with system hardware and software constraints and
requirements that must be met by the design.
2.1 System Hardware Requirements
1. The power stage must be able to switch a 1.5 kW load at a line
voltage of 230 V.
2. The solution is based on the MC68HC908QT4 microcontroller.
3. No external crystals or resonators are used.
4. Control circuit power supplies are derived from the rectified line
voltage, without a transformer. Two DC power supplies are
required: a 12 V power supply to feed the IGBT driver; and a 5 V
power supply to feed the microcontroller and control circuits.
5. There is no feedback, although the solution allows for its addition.
6. The circuit is electronically switched on and off by the
microcontroller IRQ pulse interrupt.
7. The required PWM duty cycle (a potentiometer output voltage) is
sensed by the microcontroller’s A/D converter.
8. A single layer PCB and through-hole devices are used.
2.2 System Software Requirements
1. The PWM duty cycle is set from 0% to 100% with an accuracy of
1/18 duty cycle.
2. The duty cycle accuracy can be set using a defined constant.
3. The PWM frequency can be set in a given range using a defined
constant.
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Initial Design Conditions
For More Information On This Product,
Go to: www.freescale.com
15
Freescale Semiconductor, Inc.
Initial Design Conditions
4. The PWM ramp has 18 steps (duty cycles), and the number of
steps can be set using a defined constant.
5. The PWM ramp time duration can be set using a defined constant.
6. The PWM signal can be set to invert the IGBT driver by a defined
constant.
Freescale Semiconductor, Inc...
7. The required PWM duty cycle is processed by an 8-sample
moving average filter.
Designer Reference Manual
16
DRM057 — Rev 0
Initial Design Conditions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Designer Reference Manual — Chopper using MC68HC908QT4
Section 3. Hardware Design
This section describes the system hardware solution, and provides a
block diagram, circuit schematic and PCB (printed circuit board) design.
WARNING:
This circuit is powered directly from the mains. It is dangerous to
touch any part of the circuit, even if a 0% duty cycle is generated.
Do not connect any computer, oscilloscope or development
system to this circuit without using an isolation transformer.
3.1 Hardware Description
Figure 3-1 shows a system block diagram of the chopper motor control
board. The system comprises the following five major parts.
•
Power stage
•
12 V power supply
•
Driving stage
•
5 V power supply
•
Microcontroller, with user interface.
Figure 3-2 is a schematic diagram of the chopper motor control board.
The power stage consists of the input power bridge rectifier D2 with
capacitor C1, the power IGBT transistor Q2, and the freewheeling diode
D4. Diode D7 protects the IGBT against negative spikes.
The 12 V power supply contains diode D1, and resistors for decreasing
input voltage. This follows on to an adjustable precision shunt regulator
TL431, with setting resistors R3 and R9, filtration capacitor C3, and
smoothing capacitor C2. The primary function of the 12 V source is to
feed the driving stage; a secondary function is to feed the 5 V supply.
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Hardware Design
For More Information On This Product,
Go to: www.freescale.com
17
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Hardware Design
Figure 3-1. Block Diagram
The driving stage switches the power IGBT Q2 on the base of input logic
signal from pin 7 of the microcontroller MC68HC908QT4. The IGBT is
switched on via resistor R11; it is switched off via resistor R17 and a
Schottky diode D6.
The 5 V power supply feeds the microcontroller circuit. To achieve 5 V
power supply from a 12 V source, a decreasing resistor R15, 5V1 zener
diode D5, and smoothing capacitor C4 are used.
The microcontroller circuit contains the MC68HC908QT4
microcontroller and supporting devices. The A/D converter, pin 6 of the
microcontroller, provides the conversion of the input voltage from
potentiometer R16 representing the required PWM duty cycle. Start and
stop of the PWM signal generation is made on the strength of the
interrupt generated by push button SW1 connected to pin 5 (IRQ) of
microprocessor. To filter voltage noise, capacitor C6 (pin 1) is connected
to Vdd, C7 is connected to A/D converter input (pin 6), and C7 is
connected to IRQ (pin 5).
NOTE:
The potentiometer R16 should be connected to the PCB in the required
manner. This means that if the potentiometer R16 is in a zero position,
a 0% duty cycle is required, and the 0Ω resistance must be between
“runner” and “-” of the potentiometer R16.
Designer Reference Manual
18
DRM057 — Rev 0
Hardware Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
1
2
D2
+12 V
5V1
D5
+5V
MUR160
STTH8L06D
R15 510
D7
KBU8J
+
D4
J4CON/FASTON
MOTOR
1
2
J3CON/FASTON
1
2
J2CON/FASTON
230V AC
-
DRM057 — Rev 0
Hardware Design
For More Information On This Product,
Go to: www.freescale.com
1
2
3
4
MC68HC908QT4CP
D6 BAT42
TL431
U1
Vss
Vdd
PTA5/OSC1PTA0/AD0/TCH0
PTA4/OSC2PTA1/AD1/TCH1
PTA3/RST
PTA2/IRQ
U2
R11 30
R9
6k8
R3
27k
8
7
6
5
100n
C3
+ C2
Figure 3-2. Circuit Schematic Diagram
10K
C5
PAD
PAD
PAD
R17 47
R8 68k/2W
R7 68k/2W
R6 68k/2W
R2 68k/2W
R1 68k/2W
100n
1
1
1
1M/275V
C1
D1 1N4006
IGBT
Q2
R16
+ C4
100u/16V
1
2
T+
TR
T-
MOTOROLA
470u/25V
J1CON/FASTON F1Fuse 8A
100n
C6
PWM
Q3
BC547
BC557
Q1
100n
SW1
R12 6k8
C7
Freescale Semiconductor, Inc...
R5
6k8
PWM ON/OFF
PUSH BUTTON
R14 6k8
Q4
BC547
R10
6k8
6V8
D3
R4
10k
R13 3k3
+12 V
Freescale Semiconductor, Inc.
Hardware Design
Hardware Description
Designer Reference Manual
19
Freescale Semiconductor, Inc.
Hardware Design
3.2 Parts List
Freescale Semiconductor, Inc...
Table 3-1. Parts List
DESIGNATORS
QUANTITY
DESCRIPTION
MANUFACTURER
PART NUMBER
C1
1
1M/275V
ICEL
MKT - X2 CLASS
C2
1
470u/25V ELECTROLYTIC
-
ANY ACCEPTABLE
C3,C5,C6,C7
4
100n/CERAMIC
-
ANY ACCEPTABLE
C4
1
100u/16V ELECTROLYTIC
-
ANY ACCEPTABLE
D1
1
800V/1A
FAIRCHILD
1N4006
D2
1
600V/8A DIODE BRIDGE
FAIRCHILD
KBU8J
D3
1
6V8 ZENER DIODE
-
ANY ACCEPTABLE
D4
1
ULTRAFAST DIODE
600V/8A
ST
STTH8L06D
D5
1
5V1 ZENER DIODE
-
ANY ACCEPTABLE
D6
1
30V/4A SCHOTTKY DIODE
ST
BAT42
D7
1
600V/1A ULTRAFAST DIODE
VISHAY
MUR160
F1
1
FAST FUSE
8A
ANY ACCEPTABLE
J1,J2,J3,J4
4
CONNECTOR FASTON
-
ANY ACCEPTABLE
Q1
1
-45V/-100mA PNP TRANSISTOR
FAIRCHILD
BC557
Q2
1
600V/20A HIGH FREQ. IGBT
ST
STGP20NB60H
Q3,Q4
2
45V/500mA NPN TRANSISTOR
FAIRCHILD
BC547
R1,R2,R6,R7,R8,
5
68k/2W RESISTOR
-
ANY ACCEPTABLE
R3
1
27k/0.6W RESISTOR
-
ANY ACCEPTABLE
R4,R16
2
10k/0.6W RESISTOR
-
ANY ACCEPTABLE
R5,R9,R10,R12,R14
5
6k8/0.6W RESISTOR
-
ANY ACCEPTABLE
R11
1
30/0.6W RESISTOR
-
ANY ACCEPTABLE
R13
1
3k3/0.6W RESISTOR
-
ANY ACCEPTABLE
R15
1
510/0.6W RESISTOR
-
ANY ACCEPTABLE
R17
1
47/0.6W RESISTOR
-
ANY ACCEPTABLE
SW1
1
PUSH BUTTON
-
ANY ACCEPTABLE
U1
1
ADJUSTABLE VOLTAGE REGULATOR
ON SEMICONDUCTOR
TL431
U2
1
MICROCONTROLLER
MOTOROLA
MC68HC908QT4CP
Designer Reference Manual
20
DRM057 — Rev 0
Hardware Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Hardware Design
PCB Design
3.3 PCB Design
Figure 3-3 shows the design of the tracking side of the PCB. The design
of the component side is shown in Figure 3-4.
High current in the power stage is a limiting factor in the PCB design.
Due to this current, the PCB copper thickness must be 0.35 µm at the
minimum.
Freescale Semiconductor, Inc...
All power devices (rectifier, IGBT, freewheeling diode) and the board are
mounted onto the heat sink placed under the board. The size of the heat
sink depends on the size of the load, the switching devices used, and
PWM frequency.
Figure 3-3. PCB — Track Side
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Hardware Design
For More Information On This Product,
Go to: www.freescale.com
21
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Hardware Design
Figure 3-4. PCB — Component Side
Designer Reference Manual
22
DRM057 — Rev 0
Hardware Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Designer Reference Manual — Chopper using MC68HC908QT4
Section 4. Software Design
This section describes the design of the driver software blocks. The
software is described in terms of:
•
Basic software description
•
Constants and variables definition
•
Flow chart description
•
Total microcontroller resource usage
4.1 Basic Software Description
The application controls the universal motor. A chopper control is
implemented. The software reads the user interface – the speed
potentiometer and start/stop switch. It calculates the desired speed
using a speed ramp and, accordingly, the PWM duty cycle is set and
PWM is generated on the output. The system can be viewed on three
levels (see Figure 4-1).
•
Pre-programming phase
•
Program restart
•
Main program loop
During the pre-programming phase, the user can set the program
behavior. For this purpose, some constants that determine system
behavior are defined. More about constants setup is presented in this
section.
Program restart — the program starts when the board is connected to
the mains. During this phase, a delay for system stabilization is
performed, and the constants set the microcontroller peripheral to the
required state.
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Software Design
For More Information On This Product,
Go to: www.freescale.com
23
Freescale Semiconductor, Inc.
Software Design
The main program loop is performed as long as the board remains
connected to the mains supply.
Freescale Semiconductor, Inc...
System and peripherals setup
Set configuration registers
Start
Set initial output value on port A,
Delay system start for 1.5 s to stabilize
System constants system constants :
INVERTING_DRIVER, F_PWM, K_AD
RAMP_TIME
void set_PWM(void)
{enable timer overflow interrupt, set
PWM configuration}
void set_ADC(void)
void set_IRQ(void)
Pre-programming phase
Enable interrupts
Main program loop
-
10ms interval flag
+
+
IRQ pressed flag
-
-
IRQ oscillation filter
start/stop system (electronic switch)
Is system switched on ?
+
Get sample of required speed and
compute moving average
Ramp step time over
-
+
Is actual PWM value>required?
+
Decrement actual PWM value
Is actual PWM value< required?
+
Increment actual PWM value
-
Is driver inverting?
+
Invert required PWM value
considering PWMLEVELS
-
Set output PWM value :
CH0MAX, TOV0, TCH0H, TCH0L
Figure 4-1. Main Program Flow Chart
Designer Reference Manual
24
DRM057 — Rev 0
Software Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Software Design
Constant and Variable Definitions
Timer overflow
subroutine
test PWM period flag and
choose right registers
set output PWM value to TCH0H,
TCH0L registers
set output PWM value to TCH1H,
TCH1L registers
change PWM period flag
count 10ms interval
reti
IRQ subroutine
set IRQ pressed flag
reti
Figure 4-2. Interrupt Subroutine Flow Charts
4.2 Constant and Variable Definitions
This section describes definitions and variables used in the program.
Definitions can be grouped into two categories.
•
System setup definitions — defined by programmer/user
•
Auxiliary system definitions — dependent on the system setup
definitions
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Software Design
For More Information On This Product,
Go to: www.freescale.com
25
Freescale Semiconductor, Inc.
Software Design
4.2.1 System Setup Definitions
These constants are available for the user/programmer to setup system
behavior, according to required conditions.
1. #define
PWMLEVELS
18
/*see PWM_setup.xls*/
The constant represents the number of possible PWM duty cycles
from 0% to 100% duty cycle (see the following note).
Freescale Semiconductor, Inc...
for example: If PWMLEVELS EQU 5 is defined,
then possible duty cycles are 0/4,1/4, 2/4, 3/4, 4/4.
2. #define
F_PWM
32
/*1,2,4,8,16,32,64*/
The constant sets the timer clock prescaler, thus allowing changes
to PWM frequency in a given range (see the following note).
3. #define
K_AD
15
/*see PWM_setup.xls*/
The constant transforms the value of A/D converter, from interval
<0;255> to the interval given by constant PWMLEVELS. Then the
required PWM duty cycle is given by the formula:
PWM = ADC Data register / K_AD (see the following note).
NOTE:
The constants PWMLEVELS, F_PWM, and K_AD can be easily
changed by means of the PWM_setup.xls file [1]. An example table of
PWM setup values for 3.2 MHz bus frequency, plus setup procedure,
are presented in section 4.3.2.
4. #define
RAMP_TIME
2000
/*[ms]*/
The constant defines the ramp duration from 0% PWM to 100%
PWM. Unit is one millisecond.
5. #define
INVERTING_DRIVER
0
/*x=x/1*/
The constant defines whether a non inverting (<>1) or inverting
(=1) IGBT driver is used. This feature makes it easy to apply the
program to systems where inverting drivers are used. In this
application, a non inverting driver is used.
Designer Reference Manual
26
DRM057 — Rev 0
Software Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Software Design
Constant and Variable Definitions
4.2.2 Auxiliary System Definitions
The following auxiliary system constants are used in the program, and
some of them depend upon the system setup definitions.
1. #define
TIME1
10
/*[ms]*/
Defines the system timing constant in milliseconds. All actions are
timed by their own counters that count the number of defined time
intervals.
Freescale Semiconductor, Inc...
2. #define
P_1
(PWMLEVELS-1)
An auxiliary definition for the following definitions.
3. #define
K_10MS
((TIME1*3200/(P_1*F_PWM))+1)
The constant defines the number of timer overflows during the
defined timing constant. It depends on:
i. PWM setting constants:
- prescaler - F_PWM
- number of PWM duty cycles - PWM_LEVELS
ii. timing constant - TIME1
The expression in the definition is a simplified version of the
following expression:
TIME1
BusFrequency
K_10MS = ⎛ ( int ) ⎛ ------------------- × ---------------------------------------------------------------------------------------------------------⎞ + 1⎞
⎝
⎝ 1000
⎠
( ( PWMLEVELS – 1 ) × TimerPrescaler )⎠
4. #define
RAMPSTEPTIME
(RAMP_TIME/P_TIME1)
The constant defines the time between two PWM levels change.
5. #define
K_RAMP
((RAMPSTEPTIME/TIME1)+1)
The constant defines the number of timing cycles between two
PWM levels change.
6. #define
MAXPWMVAL
P_1
The variable represents the maximal PWM duty cycle that can be
set for a chosen system setup.
MAXPWMVAL = PWMLEVELS - 1
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Software Design
For More Information On This Product,
Go to: www.freescale.com
27
Freescale Semiconductor, Inc.
Software Design
4.2.3 System Variables
This section describes static global variables used in the program.
1. static Byte ucOn_Off_PWM
Freescale Semiconductor, Inc...
The variable on_off_PWM is defined to realize an electronic
switch. This variable switches on and off PWM generated on a
given pin. If the value of this variable is 0x00, then PWM is off and
a 0% duty cycle is generated. If the value of the constant is
negated and its value is 0xFF, then the required PWM duty cycle
is generated. The variable negation depends on IRQ interrupt
(pressing push button SW1).
2. static Byte ucAct_PWM_val
The variable represents the value that tracks the required PWM
duty cycle by the given ramp.
3. static Byte ucEnd_PWM_val
The variable represents the required PWM duty cycle. It is the
result of the moving average from A/D conversions.
4. static Byte ucADCbuffer[8]
The buffer saves the last eight A/D conversion values for use in
moving average calculations.
5. static Byte uc_p_ADCbuff
The variable points to the actual position in the ucADCbuffer.
6. static Word uwSum
The variable represents the sum of all values of the ucADCbuffer.
7. static Byte ucAct_Period
The variable enables writing the required PWM duty cycle value
into the appropriate TCHxH, TCHxL registers to perform
a buffered PWM generation. It symbolizes the just finished period
(0x00 => TCH0H, TCH0L; 0xFF => TCH1H, TCH1L), The new
duty cycle value can be written into thus marked registers.
Designer Reference Manual
28
DRM057 — Rev 0
Software Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Software Design
Constant and Variable Definitions
8. static Byte ucOut_PWM
The variable represents the actual resultant value of the PWM
duty cycle that can be written into the registers TCHxH, TCHxL.
9. static Byte ucIRQ_Flag
Freescale Semiconductor, Inc...
This flag is set (0xFF) when the IRQ interrupt is generated and it
starts counting three 10 ms intervals by means of the variable
ucCountIRQ_10ms. Having finished counting, the variable is
cleared and the IRQ pin is tested again (button oscillations filter).
If its value is still log.0, the variable ucOn_Off_PWM is inverted.
Otherwise, no action is performed.
10. static Byte uc10ms_Flag
The flag informs the system that the 10 ms interval has run. This
happens when the variable ucCount_10ms, incremented at every
timer overflow, reaches constant K_10MS.
11. static Byte ucCount_10ms
The variable represents the number of timer overflows required to
generate a 10 ms interval. When the variable value reaches
constant K_10MS, the flag uc10ms_Flag is set.
12. static Byte ucCountIRQ_10ms
The variable represents the number of 10 ms intervals required to
perform an IRQ button oscillation filter. Counting starts after the
IRQ interrupt is generated. When the value of the variable is 3
(30 ms oscillation filter), and the IRQ pin still has the value log.0,
the variable ucOn_Off_PWM (software start/stop switch) is
inverted.
13. static Word uwCount_RampStep_10ms;
The variable represents the number of 10 ms intervals required to
perform PWM ramp. When the value of the variable reaches
constant K_RAMP, the PWM duty cycle can be changed.
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Software Design
For More Information On This Product,
Go to: www.freescale.com
29
Freescale Semiconductor, Inc.
Software Design
4.3 Flow Chart Description
The software flow charts can be seen in Figure 4-2. The software
solution can be divided into two parts — system plus peripherals setup
and main loop. Source code can be found in [2].
4.3.1 System Setup
Freescale Semiconductor, Inc...
Prior to running the main program loop the system setup sets the
microcontroller operation mode and peripherals. The quickest way to set
the microcontroller peripherals is to use the auxiliary excel sheet [1], or
for 3.2 MHz bus frequency, use Figure 4-3.
To achieve the required system behavior and communication with
peripherals, the following registers and initial values are set. This action
can be seen in the flow chart as subroutine calls.
1. Set configuration registers - void set_OSC(void)
The microcontroller configuration registers Config2 and Config1
initialize the microcontroller to the user defined option. They can
be written only once after each reset.
The register Config1 sets:
– disable COP
– disable STOP instruction
– disable LVI module
and the register Config2 sets:
– internal oscillator
– interrupt request function active in pin (to start and stop the
system by pressing push button SW1) (see Figure 3-2)
– IRQPUD must be 0 to connect the internal pull-up resistor
between IRQ pin and Vdd.
2. Set ADC - void Set_ADC(void)
This subroutine sets the A/D converter clock.
ADC clock = bus clock / prescaler.
Designer Reference Manual
30
DRM057 — Rev 0
Software Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Software Design
Flow Chart Description
The recommended value for the ADC clock is 1 MHz.
3. Buffered PWM setup - void Set_PWM(void)
The subroutine initializes the PWM values, sets 0% duty cycle on
the PWM output, and sets the variables for the moving average
computation.
On the strength of the constant F_PWM, the subroutine sets the
prescaler of the timer clock and the buffered PWM in the TSC
register. Subsequently, it sets the TMODH and TMODL registers
according to the value of the constant PWMLEVELS. Register
TMODH is cleared, and the value of PWMLEVELS-2 is written into
register TMODL.
For a better understanding of PWM setup and logic, see section
4.3.2 PWM Duty Cycle Setup Logic.
Moreover, timer overflow interrupt is enabled to perform buffered
PWM and system timing.
4. IRQ interrupt setup - void set _IRQ(void)
The subroutine sets IRQ interrupt on a falling edge.
4.3.2 PWM Duty Cycle Setup Logic
For setting unbuffered PWM, the timer registers must be set correctly.
Consider five levels of PWM and a non-inverting IGBT driver. That
means the PWM duty cycle can be set to {0/4, 1/4, 2/4, 3/4, 4/4} *100%.
Thus, the required PWM value can be 0, 1, 2, 3, 4.
According to MC68HC908QT4 data sheet PWM duty cycle:
•
0/4*100% (required PWM value 0). Requires clearing bits
CHxMAX and TOVx in the register TSCx.
•
1/4*100% (required PWM value 1). Requires TOVx = 1, CHxMAX
= 0, TCHxH = 0, TCHxL = required PWM value -1 = 0
•
2/4*100% (required PWM value 2). Requires TOVx = 1, CHxMAX
= 0, TCHxH = 0, TCHxL = required PWM value -1 = 1
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Software Design
For More Information On This Product,
Go to: www.freescale.com
31
Freescale Semiconductor, Inc.
Software Design
•
3/4*100% (required PWM value 3). Requires TOVx = 1, CHxMAX
= 0, TCHxH = 0, TCHxL = required PWM value -1 = 2
•
4/4*100% (required PWM value 4). Requires setting bits CHxMAX
and TOVx in the register TSCx.
If the constant INVERTING_DRIVER selects an inverting driver, the duty
cycle percentage is in an inverse order.
Freescale Semiconductor, Inc...
Timer modulo register TMODL must be set to value PWMLEVELS-2 to
ensure that the timer counts PWMLEVELS-1 times until it overflows. The
PWM frequency is affected by the setup of the prescaler value in the
TSC register. The constant F_PWM represents the prescaler value.
Consequently, the PWM frequency is given by the equation:
BusFrequency
PWM frequency = ⎛ ------------------------------------------------------------------------------------------------⎞
⎝ ( PWMLEVELS – 1 ) × TimerPrescaler⎠
[ Hz; Hz, -, - ]
The timer prescaler is represented by the constant F_PWM.
As an example, Table 4-3 presents the PWM setup for 3.2 MHz bus
frequency. The sequence of constants selection is as follows:
1. Consider a PWM with an accuracy of 18 PWM duty cycles.
(PWMLEVELS = 18 => 0/17,1/17,.......,16/17,17/17)
2. In the same line, choose one of the possible frequencies (for
example, 5882 Hz). (Make sure that the choice of PWM frequency
is feasible for the system — the limiting factor is the IGBT
switching frequency.)
3. From the same column, read timer prescaler (bits PS2,PS1,PS0
of the register TSC). In this application, the constant K_AD
represents the prescaler value of the timer.
4. If the duty cycle setup depends on the value from the A/D
converter, the resultant A/D conversion value for TCHcH, TCHxL
registers must be divided by the value K_AD read from the line
given by PWMLEVELS.
Designer Reference Manual
32
DRM057 — Rev 0
Software Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Software Design
Flow Chart Description
Freescale Semiconductor, Inc...
As can be seen, another approach comes from the PWM frequency
definition and the consequential configuration of the other parameters
given by the equation given above.
Figure 4-3. PWM Setup for 3.2 MHz Bus Frequency
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Software Design
For More Information On This Product,
Go to: www.freescale.com
33
Freescale Semiconductor, Inc.
Software Design
4.3.3 Main Program Loop
The functions of the main program loop can be summarized as follows.
•
System timing.
The whole system is timed in 10 ms intervals given by the
definition of the constant K_10MS.
•
PWM switch on/off testing.
Freescale Semiconductor, Inc...
Testing consists of comparison value of the variable
ucOn_Off_PWM. If the value is 0, then a 0% PWM duty cycle is
generated immediately, and both the actual and required PWM
values are set to 0. If the value is 0xFF, then the generated PWM
duty cycle tracks the required PWM duty cycle with a given ramp.
The variable ucOn_Off_PWM is hung on IRQ interrupt. When an
interrupt is generated, the variable ucIRQ_Flag is set. Then, after
a given time repeated IRQ pin checking eliminates push button
oscillations. If the value of the IRQ pin is still log.0, the complement
of the variable ucOn_Off_PWM is calculated.
•
A/D conversion.
•
Required PWM duty cycle tracking by the actually generated
PWM duty cycle with a delay ramp. The tracking is performed by
means of the subroutine countADCavg() that computes the
moving average from eight consecutive A/D converter values.
Designer Reference Manual
34
DRM057 — Rev 0
Software Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Software Design
Microcontroller Resource Usage
4.4 Microcontroller Resource Usage
4.4.1 ROM and RAM Usage
Table 4-1 shows software memory usage. A significant part of the
memory is still available.
Table 4-1. Memory Usage
Memory
Available on QT4
Used
ROM
4096 Bytes
680 Bytes
RAM
128 Bytes
23 Bytes
4.4.2 I/O Usage
Table 4-2 summarizes the use of the I/O pins. It can be seen that three
pins are still available.
Table 4-2. I/O Usage
I/O pin
Direction
Purpose
PTA0/AD1/TCH0/KBI0
OUTPUT
TCH0 (PWM)
PTA1/AD1/TCH1/KBI1
INPUT
AD1 (INPUT SPEED)
PTA2/IRQ/KBI2
INPUT
IRQ (ON/OFF PWM)
PTA3/\RST/KBI3
UNUSED
UNUSED
PTA4/OSC2/AD2/KBI4
UNUSED
UNUSED
PTA5/OSC1/AD3/KBI5
UNUSED
UNUSED
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Software Design
For More Information On This Product,
Go to: www.freescale.com
35
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Software Design
Designer Reference Manual
36
DRM057 — Rev 0
Software Design
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Designer Reference Manual — Chopper using MC68HC908QT4
Section 5. System Setup
WARNING:
This circuit is powered directly from the mains. It is dangerous to
touch any part of the circuit, even if a 0% duty cycle is generated.
Do not connect any computer, oscilloscope or development
system to this circuit without using an isolation transformer.
5.1 Hardware Setup
The hardware setup is very simple. Line voltage 230 V AC must be
connected to the connectors labelled “230V AC“, and motor must be
connected to the connectors labelled “DC+“ and “DC-”.
The potentiometer R16 is connected to the pads labelled “POT.10k“. For
the right potentiometer connection, see the note on page 18.
The push button SW1 is connected to the pads labelled “PUSH
BUTTON”.
5.2 Software Setup
The software setup is covered in section 4.2.1 System Setup Definitions.
5.3 Required Software Tools
Metrowerks CodeWarrior for MC68HC08 microcontrollers version 3.0,
or later is required for the development of the application.
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
System Setup
For More Information On This Product,
Go to: www.freescale.com
37
Freescale Semiconductor, Inc.
System Setup
5.4 Building and Uploading the Application
The application software is delivered as UM_Chopper_QY4.mcp project
file with C-source and header files UM_Chopper_QY4.c and
UM_Chopper_QY4.h.
The executable s19 file can be created using Metrowerks CodeWarrior.
Freescale Semiconductor, Inc...
5.5 Executing the Application
The application is prepared for operation when connected to a power
supply and the 1.5 s software delay finishes. The delay is included to
allow the system to stabilize after the mains power is connected, to
prevent unwanted PWM generation.
Subsequently, the START/STOP push button SW1 can be pressed to
start PWM generation. The PWM duty cycle is set by the potentiometer
R16 with a given ramp.
Designer Reference Manual
38
DRM057 — Rev 0
System Setup
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Designer Reference Manual — Chopper using MC68HC908QT4
Appendix A. Abbreviations and Definitions
AC
alternating current.
A/D converter, ADC
analog to digital converter: the module is a 4-channel, multiplexed-input
successive-approximation analog to digital converter.
Buffered
a system that uses two registers for data; new data is read alternately.
Bus clock
the clock signal on the CPU’s internal bus. See “CPU cycles”.
Clear
to change a bit from logic 1 to logic 0; the opposite of to set.
Clock
a square wave signal used to synchronize events in a computer.
COP
computer operating properly.
CPU
central processing unit.
CPU cycles
a CPU cycle is one period of the internal bus clock, normally derived by
dividing a crystal oscillator source by two or more so the high and low times
will be equal. The length of time required to execute an instruction is
measured in CPU clock cycles.
CISC
complex instruction set computer.
Cycle time
The period of the operating frequency: tcyc = 1/fop.
DC
direct current.
Duty cycle
the ratio of the amount of time the signal is on to the time it is off. Duty cycle
is usually represented by a percentage.
EMC
electromagnetic compatibility.
Interrupt
a temporary break in the sequential execution of a program to respond to
signals from peripheral devices by executing a subroutine.
Interrupt request
a signal from a peripheral to the CPU intended to cause the CPU to execute
a subroutine.
IGBT
insulated gate bipolar transistor.
I/O
input/output.
Logic 1
a voltage level approximately equal to the input power voltage (Vdd).
DRM057 — Rev 0
MOTOROLA
Designer Reference Manual
Abbreviations and Definitions
For More Information On This Product,
Go to: www.freescale.com
39
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Abbreviations and Definitions
Logic 0
a voltage level approximately equal to the ground voltage (Vss).
LVI
low voltage inhibit.
MCU
microcontroller unit: a complete computer system, including a CPU, memory,
a clock oscillator, and input/output (I/O) on a single integrated circuit.
Oscillator
a circuit that produces a constant frequency square wave that is used by the
computer as a timing and sequencing reference.
Overflow
a quantity that is too large to be contained in one byte or one word.
PCB
printed circuit board.
Peripheral
a circuit not under direct CPU control.
Prescaler
a circuit that divides input signal by given value.
Program
a set of computer instructions that cause a computer to perform a desired
operation or operations.
PWM
pulse width modulation: controlled variation (modulation) of the pulse width
of a signal with a constant frequency.
PWM period
the duration of one complete cycle of a PWM waveform.
RAM
random access memory. All RAM locations can be read or written by the
CPU. The contents of a RAM memory location remain valid until the CPU
writes a different value or until power is turned off.
Register
a circuit that stores a group of bits.
Reset
to force a device to a known condition.
Set
to change a bit from logic 0 to logic 1; opposite of clear.
Software
instructions and data that control the operation of a microcontroller.
Subroutine
a sequence of instructions to be used more than once in the course of a
program. The last instruction in a subroutine is a return from subroutine
(RTS) instruction. At each place in the main program where the subroutine
instructions are needed, a jump or branch to subroutine (JSR or BSR)
instruction is used to call the subroutine. The CPU leaves the flow of the
main program to execute the instructions in the subroutine. When the RTS
instruction is executed, the CPU returns to the main program where it left off.
Timer
a module used to relate events in a system to a point in time.
Unbuffered
a system that uses only one register for data; new data overwrites current
data.
Variable
a value that changes during the course of program execution.
Word
a set of two bytes (16 bits).
Designer Reference Manual
40
DRM057 — Rev 0
Abbreviations and Definitions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
HOW TO REACH US:
USA/EUROPE/LOCATIONS NOT LISTED:
Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217
1-303-675-2140 or 1-800-441-2447
JAPAN:
Motorola Japan Ltd.; SPS, Technical Information Center,
3-20-1, Minami-Azabu Minato-ku, Tokyo 106-8573 Japan
81-3-3440-3569
ASIA/PACIFIC:
Motorola Semiconductors H.K. Ltd.;
Silicon Harbour Centre, 2 Dai King Street,
Tai Po Industrial Estate, Tai Po, N.T., Hong Kong
852-26668334
Information in this document is provided solely to enable system and software
implementers to use Motorola products. There are no express or implied copyright
licenses granted hereunder to design or fabricate any integrated circuits or
integrated circuits based on the information in this document.
TECHNICAL INFORMATION CENTER:
Motorola reserves the right to make changes without further notice to any products
1-800-521-6274
herein. Motorola makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Motorola assume any
HOME PAGE:
http://motorola.com/semiconductors
liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental
damages. “Typical” parameters which may be provided in Motorola data sheets
and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts.
Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which
the failure of the Motorola product could create a situation where personal injury or
death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated
with such unintended or unauthorized use, even if such claim alleges that Motorola
was negligent regarding the design or manufacture of the part.
Motorola and the Stylized M Logo are registered in the U.S. Patent and Trademark
Office. digital dna is a trademark of Motorola, Inc. All other product or service
names are the property of their respective owners. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
© Motorola, Inc. 2004
DRM057
For More Information On This Product,
Go to: www.freescale.com