DS1813 5V EconoReset with Pushbutton www.dalsemi.com FEATURES PIN ASSIGNMENT Automatically restarts a microprocessor after power failure Monitors pushbutton for external override Maintains reset for typically 150 ms after VCC returns to an in-tolerance condition Reduces need for discrete components Precision temperature-compensated voltage reference and voltage sensor Low-cost TO-92 or space saving surfacemount SOT-23 packages available Efficient open-drain output with internal 5.5 kΩ=pull-up resistor Operating temperature -40°C to +85°C 3 1 2 SOT-23 PACKAGE 1 2 3 1 2 3 TO-92 PACKAGE See Mech. Drawings Section PIN DESCRIPTION TO-92 1 2 3 RST VCC GND Active Low Reset Output Power Supply Ground SOT-23 1 2 3 RST VCC GND Active Low Reset Output Power Supply Ground DESCRIPTION The DS1813 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition, the reset signal is kept in the active state for approximately 150 ms to allow the power supply and processor to stabilize. The DS1813 also monitors a pushbutton on the reset output. If the reset line is pulled low, a reset is generated upon release and will be held in reset output low for typically 150 ms. 1 of 5 Powered by ICminer.com Electronic-Library Service CopyRight 2003 111999 DS1813 OPERATION - POWER MONITOR The DS1813 provides the functions of detecting out-of-tolerance power supply conditions and warning a processor-based system of impending power failure. When VCC is detected as out-of-tolerance, the RST signal is asserted. On power-up, RST is kept active for approximately 150 µs after the power supply has reached the selected tolerance. This allows the power supply and microprocessor to stabilize before RST is released. OPERATION - PUSHBUTTON RESET The DS1813 provides for a pushbutton switch for manual reset control. When the DS1813 is not in a reset cycle, a pushbutton reset can be generated by pulling the RST pin low for at least 1 ms. When the pushbutton is held low, the RESET is forced active low and will remain active low for about 150 ms after the pushbutton is released. See Figure 2 for an application example and Figure 3 for the timing diagram. BLOCK DIAGRAM (OPEN-DRAIN OUTPUT) Figure 1 APPLICATION EXAMPLE Figure 2 2 of 5 Powered by ICminer.com Electronic-Library Service CopyRight 2003 DS1813 TIMING DIAGRAM: PUSHBUTTON RESET Figure 3 TIMING DIAGRAM: POWER-UP Figure 4 TIMING DIAGRAM: POWER-DOWN Figure 5 3 of 5 Powered by ICminer.com Electronic-Library Service CopyRight 2003 DS1813 ABSOLUTE MAXIMUM RATINGS* Voltage on VCC Pin Relative to Ground Voltage on RST Relative to Ground Operating Temperature Storage Temperature Soldering Temperature * -0.5V to +7.0V -0.5V to +5VCC +0.5V -40°C to +85°C -55°C to +125°C 260°C for 10 seconds This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER Supply Voltage SYMBOL VCC DC ELECTRICAL CHARACTERISTICS PARAMETER MIN 0.0 MIN Output Current @ 0.4 volts IOL +10 Voltage Input Low VIL Voltage Input High VIH Operating Current VCC < 5.5 ICC VCC Trip Point (DS1813-5) VCCTP VCC Trip Point (DS1813-10) VCC Trip Point (DS1813-15) Output Capacitance MAX 5.5 UNITS V TYP MAX 0.4 0.7 *VCC UNITS NOTES mA 2, 3 V 1 V 1 40 µA 4 4.50 4.62 4.75 V 1 VCCTP 4.25 4.35 4.49 V 1 VCCTP 4.00 4.13 4.24 V 1 RP 3.50 5.5 7.5 k 6 10 pF COUT (-40°C to +85°C; VCC=1.2V to 5.5V) SYMBOL MIN TYP MAX UNITS RESET Active Time tRST 100 150 300 ms VCC Detect to RST tRPD 2 5 µs VCC Slew Rate (VCCTP (MAX) - VCCTP (MIN)) tF 300 µs VCC Slew Rate (VCCTP (MIN) - VCCTP (MAX)) tR 0 ns VCC Detect to RST tRPU 100 Pushbutton Detect to RST tPB 1 tPBRST 100 Pushbutton Reset 4 of 5 Powered by ICminer.com Electronic-Library Service CopyRight 2003 NOTES 1 30 AC ELECTRICAL CHARACTERISTICS PARAMETER TYP (-40°C to +85°C; VCC=1.2V to 5.5V) SYMBOL Internal Pull-Up Resistor (-40°C to +85°C) 150 300 ms µs 150 300 ms NOTES 7 5 DS1813 NOTES: 1. All voltages are referenced to ground. 2. Measured with VCC ≥ 2.7 volts. 3. A 1kΩ=external resistor may be required in some applications for proper operation of the microprocessor reset control circuit. 4. Measured with RST output open. 5. tR = 5 µs. 6. VOH and IOH are a function of the value of RP and the associated output load conditions. 7. This value is for reference in defining values for TRPD and should not be considered a requirement for proper operation or use of the device. PART MARKING CODES “A”, “B”, &“C” represent the device type. 810 . . . . DS1810 811 . . . . DS1811 812 . . . . DS1812 813 . . . . DS1813 815 . . . . DS1815 816 . . . . DS1816 817 . . . . DS1817 818 . . . . DS1818 “D” represents the device tolerance. A . . . . . . 5% B . . . . . . 10% C . . . . . . 15% D . . . . . . 20% 5 of 5 Powered by ICminer.com Electronic-Library Service CopyRight 2003