DS36C280 Slew Rate Controlled CMOS EIA-RS-485 Transceiver General Description Features The DS36C280 is a low power differential bus/line transceiver designed to meet the requirements of RS-485 Standard for multipoint data transmission. In addition, it is compatible with TIA/EIA-422-B. The slew rate control feature allows the user to set the driver rise and fall times by using an external resistor. Controlled edge rates can reduce switching EMI. n 100% RS-485 compliant — Guaranteed RS-485 device interoperation n Low power CMOS design: ICC 500 µA max n Adjustable slew rate control — Minimizes EMI affects n Built-in power up/down glitch-free circuitry — Permits live transceiver insertion/displacement n DIP and SOIC packages available n Industrial temperature range: −40˚C to +85˚C n On-board thermal shutdown circuitry — Prevents damage to the device in the event of excessive power dissipation n Wide common mode range: −7V to +12V n Receiver open input fail-safe (Note 1) n 1⁄4 unit load (DS36C280): ≥128 nodes n 1⁄2 unit load (DS36C280T): ≥64 nodes n ESD (human body model): ≥2 kV The CMOS design offers significant power savings over its bipolar and ALS counterparts without sacrificing ruggedness against ESD damage. The device is ideal for use in battery powered or power conscious applications. ICC is specified at 500 µA maximum. The driver and receiver outputs feature TRI-STATE ® capability. The driver outputs operate over the entire common mode range of −7V to +12V. Bus contention or fault situations are handled by a thermal shutdown circuit, which forces the driver outputs into the high impedance state. The receiver incorporates a fail safe circuit which guarantees a high output state when the inputs are left open (Note 1) . Connection and Logic Diagram Truth Table DRIVER SECTION DE/RE* DI DO/RI H H H DO*/RI* L H L L H L X Z Z RECEIVER SECTION DS012052-1 Order Number DS36C280TM, DS36C280TN DS36C280M and DS36C280N See NS Package Number M08A or N08E DE/RE* RI-RI* RO L ≥+0.2V H L ≤−0.2V L H X Z L OPEN (Note 1) H Note 1: Non-terminated, Open Inputs only TRI-STATE ® is a registered trademark of National Semiconductor Corporation. © 1999 National Semiconductor Corporation DS012052 www.national.com DS36C280 Slew Rate Controlled CMOS EIA-RS-485 Transceiver July 1998 Absolute Maximum Ratings (Note 2) Storage Temperature Range Lead Temperature (Soldering 4 sec.) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. −65˚C to +150˚C +260˚C Recommended Operating Conditions Supply Voltage (VCC) +12V Input Voltage (DE/RE*, & DI) −0.5V to (VCC +0.5V) Common Mode (VCM) ± 15V Driver Output/Receiver Input ± 14V Input Voltage (DO/RI, DO*/RI*) Receiver Output Voltage −0.5V to (VCC +0.5V) Maximum Package Power Dissipation @ +25˚C M Package 1190 mV, derate 9.5 mW/˚C above +25˚C N Package 794 mV, derate 6.0 mW/˚C above +25˚C Min +4.75 Supply Voltage (VCC) Bus Voltage −7 Operating Free Air Temperature (TA) DS36C280T −40 DS36C280 0 Typ +5.0 Max +5.25 +12 Units V V +25 +25 +85 +70 ˚C ˚C Electrical Characteristics (Notes 3, 4) Over Supply Voltage and Operating Temperature ranges, unless otherwise specified Symbol Parameter Conditions Reference Min Typ Max Units 1.5 5.0 V 0 5.0 V 0 5.0 V DIFFERENTIAL DRIVER CHARACTERISTICS VOD1 Differential Output Voltage IO = 0 mA (No Load) VOD0 Output Voltage IO = 0 mA VOD0* Output Voltage (Output to GND) VOD2 Differential Output Voltage (Termination Load) RL = 50Ω (422) RL = 27Ω (485) Balance of VOD2 RL = 27Ω or 50Ω ∆VOD2 (422) (485) (Note 5) |VOD2 − VOD2*| VOD3 VOC ∆VOC IOSD Figure 1 2.0 2.8 1.5 2.3 5.0 V V −0.2 0.1 +0.2 V 1.5 2.0 5.0 V 0 3.0 V 0 3.0 V −0.2 +0.2 V (422, 485) Figure 2 Differential Output Voltage (Full Load) VTEST = −7V to +12V R1 = 54Ω, R2 = 375Ω Driver Common Mode Output Voltage RL = 27Ω (485) RL = 50Ω (422) Balance of VOC RL = 27Ω or Figure 1 (Note 5) |VOC − VOC*| RL = 50Ω Driver Output Short-Circuit Current VO = +12V (485) Figure 4 200 +250 mA VO = −7V (485) −190 −250 mA +0.035 +0.2 V (422, 485) RECEIVER CHARACTERISTICS VTH VTL Differential Input High Threshold Voltage −7V ≤ VCM ≤ +12V VO = VOH, IO = −0.4 mA Differential Input Low Threshold Voltage −7V ≤ VCM ≤ +12V (Note 6) (422, 485) VO = VOL, IO = 0.4 mA −0.2 −0.035 V VHST Hysteresis VCM = 0V 70 mV RIN Input Resistance −7V ≤ VCM ≤ +12V DS36C280T 24 68 kΩ RIN Input Resistance −7V ≤ VCM ≤ +12V DS36C280 48 68 IIN Line Input Current (Note 8) Other Input = 0V VIN = +12V 0 0.19 0.25 mA VIN = −7V 0 −0.1 −0.2 mA VIN = +12V 0 0.19 0.5 mA VIN = −7V 0 −0.1 −0.4 mA DS36C280 DE = VIL, RE* = VIL VCC = 4.75 to 5.25 DS36C280T or 0V IING Line Input Current Glitch (Note 8) Other Input = 0V DS36C280 DE = VIL, RE* = VIL VCC = +3.0V DS36C280T or 0V TA = 25˚C IB Input Balance Test RS = 500Ω VOH High Level Output Voltage IOH = −4 mA, VID = +0.2V VOL Low Level Output Voltage IOL = +4 mA, VID = −0.2V www.national.com VIN = +12V 0 0.19 0.25 mA VIN = −7V 0 −0.1 −0.2 mA VIN = +12V 0 0.19 0.5 mA VIN = −7V 0 −0.1 −0.4 mA ± 400 mV 3.5 4.6 (422) (Note 10) 2 kΩ RO Figure 11 0.3 V 0.5 V Electrical Characteristics (Notes 3, 4) (Continued) Over Supply Voltage and Operating Temperature ranges, unless otherwise specified Symbol Parameter Conditions Reference Min Typ RO 7 35 Max Units RECEIVER CHARACTERISTICS IOSR Short Circuit Current VO = GND IOZR TRI-STATE Leakage Current VO = 0.4V to 2.4V 85 mA ±1 µA V DEVICE CHARACTERISTICS VIH High Level Input Voltage 2.0 VCC VIL Low Level Input Voltage GND 0.8 V IIH High Level Input Current 2 µA IIL Low Level Input Current −2 µA DE/RE*, DI VIH = VCC VCC = 5.0V VIL = 0V VCC = +3.0V SR = 0V ICCR ICCD Power Supply Current (No Load) −2 µA −1 mA 200 500 µA 200 500 µA SR Driver OFF, Receiver ON VCC Driver ON, Receiver OFF Switching Characteristics (Notes 4, 9, 11) Over Supply Voltage and Operating Temperature ranges, unless otherwise specified Symbol Parameter Conditions Reference Min Typ Max Units RL = 54Ω, CL = 100 pF Figures 5, 6 10 399 1000 ns DRIVER CHARACTERISTICS tPHLD Differential Propagation Delay High to Low tPLHD Differential Propagation Delay Low to High 10 400 1000 ns tSKD Differential Skew 0 1 10 ns |tPHLD − tPLHD| tr Rise Time tf Fall Time tr Rise Time tf Fall Time tr Rise Time tf Fall Time tPHZ Disable Time High to Z tPLZ Disable Time Low to Z tPZH Enable Time Z to High tPZL Enable Time Z to Low SR = Open 2870 SR = 100 kΩ ns 3070 ns 1590 ns 1640 SR = Short 100 100 CL = 15 pF CL = 100 pF 337 ns 1000 ns 348 1000 ns Figures 7, 8 1100 2000 ns Figures 9, 10 500 800 ns Figures 7, 8 300 500 ns Figures 9, 10 300 500 ns 30 210 400 ns 30 190 400 ns RECEIVER CHARACTERISTICS tPHL Propagation Delay High to Low tPLH Propagation Delay Low to High tSK Skew, |tPHL − tPLH| tPLZ Output Disable Time CL = 15 pF Figures 12, 13 0 CL = 15 pF tPHZ tPZL Figures 14, 15, 16 Output Enable Time tPZH 20 50 ns 50 150 ns 55 150 ns 40 150 ns 45 150 ns Note 2: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD1 and VOD2. Note 4: All typicals are given for: VCC = +5.0V, TA = + 25˚C. Note 5: Delta |VOD2| and Delta |VOC| are changes in magnitude of VOD2 and VOC, respectively, that occur when input changes state. 3 www.national.com Switching Characteristics (Notes 4, 9, 11) (Continued) Note 6: Threshold parameter limits specified as an algebraic value rather than by magnitude. Note 7: Hysteresis defined as VHST = VTH − VTL. Note 8: IIN includes the receiver input current and driver TRI-STATE leakage current. Note 9: CL includes probe and jig capacitance. Note 10: For complete details of test, see RS-485. Note 11: SR = GND for all Switching Characteristics unless otherwise specified. Parameter Measurement Information DS012052-2 FIGURE 1. Driver VOD2 and VOC DS012052-5 FIGURE 5. Driver Differential Propagation Delay Test Circuit DS012052-18 FIGURE 2. Driver VOD3 DS012052-3 FIGURE 3. Driver VOH and VOL DS012052-6 FIGURE 6. Driver Differential Propagation Delays and Differential Rise and Fall Times DS012052-4 Vtest = −7V to +12V FIGURE 4. Driver IOSD DS012052-7 FIGURE 7. TRI-STATE Test Circuit (tPZH , tPHZ) www.national.com 4 Parameter Measurement Information (Continued) DS012052-10 FIGURE 10. TRI-STATE Waveforms (tPZL, tPLZ) DS012052-8 FIGURE 8. TRI-STATE Waveforms (tPZH, tPHZ) DS012052-11 FIGURE 11. Receiver VOH and VOL DS012052-9 FIGURE 9. TRI-STATE Test Circuit (tPZL, tPLZ) DS012052-12 FIGURE 12. Receiver Differential Propagation Delay Test Circuit DS012052-13 FIGURE 13. Receiver Differential Propagation Delay Waveforms DS012052-14 FIGURE 14. Receiver TRI-STATE Test Circuit 5 www.national.com Parameter Measurement Information (Continued) DS012052-15 FIGURE 15. Receiver Enable and Disable Waveforms (tPLZ, tPZL) DS012052-16 FIGURE 16. Receiver Enable and Disable Waveforms (tPHZ, tPZH) Typical Application Information DS012052-17 FIGURE 17. Typical Pin Connection TABLE 1. Device Pin Descriptions Pin # Name Description 1 RO Receiver Output: When DE/RE* (Receiver Enable) is LOW, the receiver is enabled (ON), if DO/RI ≥ DO*/RI* by 200 mV, RO will be HIGH. If DO/RI ≤ DO*/RI* by 200 mV, RO will be LOW. Additionally RO will be HIGH for OPEN (Non-terminated) inputs. 2 SR Slew Rate Control: A resistor connected to Ground controls the Driver Output rising and falling edge rates. 3 DE/RE* Combined Driver and Receiver Output Enable: When signal is LOW the receiver output is enabled and the driver outputs are in TRI-STATE (OFF). When signaI is HlGH, the receiver output is in TRI-STATE (OFF) and the driver outputs are enabled. 4 DI Driver Input: When DE/RE* is HlGH, the driver is enabled, if DI is LOW, then DO/RI will be LOW and DO*/RI* will be HIGH. If DI is HIGH, then DO/RI is HIGH and DO*/RI* is LOW. www.national.com 6 Typical Application Information (Continued) TABLE 1. Device Pin Descriptions (Continued) Pin # Name Description 5 GND 6 DO/RI Ground Connection Driver Output/Receiver Input, 485 Bus Pin. 7 DO*/RI* Driver Output/Receiver Input, 485 Bus Pin. 8 VCC Positive Power Supply Connection: Recommended operating range for VCC is +4.75V to +5.25V. DS36C280 has a slew rate control for EMI conscious applications. Refer to the sleep mode and slew rate control portion of the application information section in the corresponding datasheet for more information on these features. Unit Load A unit load for a RS-485 receiver is defined by the input current versus the input voltage curve. The gray shaded region is the defined operating range from −7V to +12V. The top border extending from −3V at 0 mA to +12V at +1 mA is defined as one unit load. Likewise, the bottom border extending from +5V at 0 mA to −7V at −0.8 mA is also defined as one unit load (see Figure 18 ). A RS-485 driver is capable of driving up to 32 unit loads. This allows upto 32 nodes on a single bus. Although sufficient for many applications, it is sometime desirable to have even more nodes. For example an aircraft that has 32 rows with 4 seats per row could benefit from having 128 nodes on one bus. This would allow signals to be transferred to and from each individual seat to 1 main station. Usually there is one or two less seats in the last row of the aircraft near the restrooms and food storage area. This frees the node for the main station. The DS36C278, the DS36C279, and the DS36C280 all have 1⁄2 unit load and 1⁄4 unit load (UL) options available. These devices will allow upto 64 nodes or 128 nodes guaranteed over temperature depending upon which option is selected. The 1⁄2 UL option is available in industrial temperature and the 1⁄4 UL is available in commercial temperature. First, for a 1⁄2 UL device the top and bottom borders shown in Figure 18 are scaled. Both 0 mA reference points at +5V and −3V stay the same. The other reference points are +12V at +0.5 mA for the top border and −7V at −0.4 mA for the bottom border (see Figure 18 ). Second, for a 1⁄4 UL device the top and bottom borders shown in Figure 18 are scaled also. Again, both 0 mA reference points at +5V and −3V stay the same. The other reference points are +12V at +0.25 mA for the top border and −7V at −0.2 mA for the bottom border (see Figure 18 ). The advantage of the 1⁄2 UL and 1⁄4 UL devices is the increased number of nodes on one bus. In a single master multi-slave type of application were the number of slaves exceeds 32, the DS36C278/279/280 may save in the cost of extra devices like repeaters, extra media like cable, and/or extra components like resistors. The DS36C279 and DS36C280 have addition feature which offer more advantages. The DS36C279 has an automatic sleep mode function for power conscious applications. The DS012052-19 FIGURE 18. Input Current vs Input Voltage Operating Range Slew Rate Control The DS36C280 features an adjustable slew rate control. This feature allows more control over EMl levels than tradition fixed edge rate devices. The slew rate control may be adjusted with or without any external components. The DS36C280 offers both low power (ICC 500 µA max) and low EMI for an RS-485 interface. The slew rate control is located at pin two of the device and only controls the driver output edges. The slew rate control pin (SR) may be left open or shorted to ground, with or without a resistor. When the SR pin is shorted to ground without a resistor, the driver output edges will transition typically 350 ns. When the SR pin is left open, the driver output edges will transition typically 3 µs. When the SR pin is shorted to ground with a resistor, the driver output edges will transition between 350 ns and 3 µs depending on the resistor value. Refer to the slew rate versus resistor value curve in this datasheet for determining resistor values and expected typical slew rate value. Please note, when slowing the edge rates of the device (see Figure 19 ) will decrease the maximum data rate also. 7 www.national.com Slew Rate Control (Continued) Differential Rise/Fall Time vs Slew Rate Resistor DS012052-20 FIGURE 19. Slew Rate Resistor vs Rise/Fall Time www.national.com 8 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead (0.150" Wide) Molded Small Outline Package, JEDEC Order Number DS36C280TM NS Package Number M08A 8-Lead (0.300" Wide) Molded Dual-In-Line Package Order Number DS36C280TN NS Package Number N08E 9 www.national.com DS36C280 Slew Rate Controlled CMOS EIA-RS-485 Transceiver LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component is any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness. ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.