Aluminum Electrolytic Capacitors/TA Surface Mount Type Series: TA n Features V Type : Country of Origin Japan Endurance:125°C 1000 h For use near car engines. Good for electronically controlled units (ECU, ABS etc). Vibration-proof product is available upon request.(φ8 < =) RoHS directive not compliant. TG series is recommended for RoHS compliant. n Specifications Category temp. range -40 to +125°C Rated W.V. Range 10 to 50 V .DC 10 to 330 µ F Nominal Cap. Range Capacitance Tolerance DC Leakage Current tan δ ±20 % (120Hz/+20°C) I 0.01 CV or 3(µ A) after 2 minutes (Whichever is greater) Please see the attached standard products list < = W.V. (V) -25 / +20 °C -40 / +20 °C Characteristics at Low Temperature 10 8 14 16 5 12 25 4 10 35 3 8 50 3 8 (Impedance ratio at 120Hz) After applying rated working voltage for 1000 hours at +125 ±2°C and then being stabilized at +20°C, capacitors shall meet the following limits. Capacitance change ±30 % of initial measured value < 300 % of initial specified value tan δ = < initial specified value DC leakage current = After storage for 500 hours at +125 ±2°C with no voltage applied and then being stabilized at +20°C, capacitors shall meet the following limits. (With voltage treatment) ±20% of initial measured value Capacitance change < tan δ = 200 % of initial specified value < DC leakage current = initial specified value After reflow soldering and then being stabilized at +20°C, capacitor shall meet the following limits. ±10 % of initial measured value Capacitance change < tan δ = initial specified value < DC leakage current = initial specified value Endurance Shelf Life Resistance to Soldering Heat n Marking n Dimensions in mm (not to scale) Example: 16V 100 µF (Polarized) ( ) reference size K Series identification (P) B±0.2 (mm) Lot number Size L A,B H I W P code D E 8.0 6.2 8.3 9.5 MAX 3.4 0.65±0.1 2.2 F 8.0 10.2 8.3 10.0 MAX 3.4 0.90±0.2 3.1 G 10.0 10.2 10.3 12.0 MAX 3.5 0.90±0.2 4.6 W.V. code V Code w L ±0.3 (I) C TA H Capacitance (µF) 100 Negative polarity marking φD±0.5 W.V. code (I) A±0.2 0.3 max 10 16 25 35 50 A C E V H K 0.35 - 0.20 to +0.15 0.70 ±0.2 0.70 ±0.2 n Case size W.V.(V) Cap. (µF) 10 22 33 47 100 220 330 10 (1A) E F G 16 (1C) F G 25 (1E) E F 35 (1V) E F G 50 (1H) E E F G Design, and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and / or use. Should a safety concern arise regarding this product,please be sure to contact us immediately. Apr. 2005 EE48 Aluminum Electrolytic Capacitors/TA n Standard Products W.V. Cap. 16 25 35 50 (120Hz) (+20°C) Part No. (RoHS: not compliant) Min. Packaging Q'ty Taping Length (µF) (mm) (mm) 100 8 6.2 E 62 0.32 EEVTA1A101P (2) 1000 220 8 10.2 F 93 0.32 EEVTA1A221P (2) 500 330 10 10.2 G 118 0.32 EEVTA1A331P (2) 500 100 8 10.2 F 89 0.24 EEVTA1C101P (2) 500 220 10 10.2 G 113 0.24 EEVTA1C221P (2) 500 47 8 6.2 E 56 0.21 EEVTA1E470P (2) 1000 100 8 10.2 F 84 0.21 EEVTA1E101P (2) 500 33 8 6.2 E 53 0.18 EEVTA1V330P (2) 1000 47 8 10.2 F 79 0.18 EEVTA1V470P (2) 500 100 10 10.2 G 101 0.18 EEVTA1V101P (2) 500 10 8 6.2 E 25 0.18 EEVTA1H100P (2) 1000 22 8 6.2 E 50 0.18 EEVTA1H220P (2) 1000 33 8 10.2 F 74 0.18 EEVTA1H330P (2) 500 10 10.2 0.18 EEVTA1H470P (2) 500 47 Size Code G 94 Reflow 10 Specification tan δ Ripple current (100kHz) (+125°C) (m A ) Dia. (±20%) (V) Case size (pcs) The taping dimensions are explained on p.187 of our Catalog. Please use it as a reference guide. Endurance : 125°C 1000h Reflow profile(Fig-1 to Fig-5) listed on the last page. Design, and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and / or use. Should a safety concern arise regarding this product,please be sure to contact us immediately. Apr. 2005 EE49 Pre-fix Suffix Case Diameter ECE-V RoHS Terminal Compliant Finish Reflow Condition Peak Temperature Time above 200℃ Reflow Chart R 3mm to 5mm No Sn-Pb 240℃ for 5 seconds 20 seconds (1) Fig.1 P 6mm No Sn-Pb 240℃ for 5 seconds 20 seconds (1) Fig.1 P 8mm to 10mm No Sn-Pb 230℃ for 5 seconds 20 seconds (2) Fig.2 R 4mm to 5mm No Sn-Pb 240℃ for 5 seconds 20 seconds (1) Fig.1 P 6mm No Sn-Pb 240℃ for 5 seconds 20 seconds (1) Fig.1 P 8mm to 10mm No Sn-Pb 230℃ for 5 seconds 20 seconds (2) Fig.2 Q 12.5mm Yes Sn 230℃ for 5 seconds 20 seconds EEV- (2) Fig.2 (Except for EB series) (3) Fig.3 (EB series only) (2) Fig.2 (Except for EB series) M 16mm to 18mm Yes Sn 230℃ for 5 seconds 20 seconds (3) Fig.3 (EB series only) EEE- R 3mm to 5mm Yes Sn-Bi 250℃ for 5 seconds 60 seconds (4) Fig.4 P 6mm Yes Sn-Bi 250℃ for 5 seconds 60 seconds (4) Fig.4 P 8mm to 10mm Yes Sn-Bi 235℃ for 5 seconds 60 seconds (5) Fig.5 (1) (2) Fig. 1 Fig. 2 260 Peak temperature / deg.C Peak temperature / deg.C 260 250 240 230 220 210 200 250 240 230 220 210 200 0 10 20 30 40 50 60 70 0 10 20 30 40 50 60 70 Time in 200deg.C or more / s Time in 200deg.C or more / s (3) (4) Fig. 3 Fig. 4 260 Peak temperature / deg.C Peak temperature / deg.C 260 250 240 230 220 210 200 10 20 30 40 50 60 70 230 220 210 (5) Fig. 5 260 250 240 230 220 210 200 10 20 30 40 50 Time in 200deg.C or more / s 0 10 20 30 40 50 Time in 200deg.C or more / s Time in 200deg.C or more / s Peak temperature / deg.C 240 200 0 0 250 60 70 60 70