EL5225 ® Data Sheet 10-Channel TFT-LCD Reference Voltage Generator The EL5225 is designed to produce the reference voltages required in TFT-LCD applications. Each output is programmed to the required voltage with 10 bits of resolution. Reference pins determine the high and low voltages of the output range, which are capable of swinging to either supply rail. Programming of each output is performed using the 3-wire, SPI compatible interface. A number of the EL5225 can be stacked for applications requiring more than 10 outputs. The reference inputs can be tied to the rails, enabling each part to output the full voltage range, or alternatively, they can be connected to external resistors to split the output range and enable finer resolutions of the outputs. The EL5225 has 10 outputs, and is available in the 24-pin TSSOP package. They are specified for operation over the full -40°C to +85°C temperature range. Ordering Information PART NUMBER (See Note) FN7356.0 Features • 10-channel reference outputs • Accuracy of ±1% • Supply voltage of 5V to 16.5V • Digital supply 3.3V to 5V • Low supply current of 9mA • Rail-to-rail capability • Pb-free available (RoHS compliant) Applications • TFT-LCD drive circuits • Reference voltage generators Pinout EL5225 (24-PIN TSSOP) TOP VIEW ENA 1 24 OUTA SDI 2 23 OUTB MDP0044 SCLK 3 22 OUTC 7” MDP0044 SDO 4 13” MDP0044 EXT_OSC 5 20 OUTD VS+ 6 19 OUTE VSD 7 18 OUTF REFH 8 17 OUTG REFL 9 16 GND PACKAGE (Pb-Free) TAPE & REEL PKG. DWG. # EL5225IRZ 24-Pin TSSOP - EL5225IRZ-T7 24-Pin TSSOP EL5225IRZ-T13 24-Pin TSSOP NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020C. 1 March 11, 2004 21 GND VS+ 10 15 OUTH GND 11 14 OUTI CAP 12 13 OUTJ CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002-2004. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners. EL5225 Absolute Maximum Ratings (TA = 25°C) Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Supply Voltage between VS & GND. . . . . . . . 4.5V (min) to 18V (max) Supply Voltage between VSD & GND . . 3V (min) to VS and 7V (max) Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 30mA Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VS = 15V, VSD = 5V, VREFH = 13V, VREFL = 2V, RL = 1.5kΩ and CL = 200pF to 0V, TA = 25°C, unless otherwise specified. DESCRIPTION CONDITIONS MIN TYP MAX UNIT 9 11.5 mA 0.17 0.35 mA 50 150 mV SUPPLY IS Supply Current ISD Digital Supply Current No load ANALOG VOL Output Swing Low Sinking 5mA (VREFH = 15V, VREFL = 0) VOH Output Swing High Sourcing 5mA (VREFH = 15V, VREFL = 0) ISC Short Circuit Current PSRR Power Supply Rejection Ratio tD Program to Out Delay VAC Accuracy referred to the ideal value ∆VMIS Channel to Channel Mismatch VDROOP Droop Voltage 1 RINH Input Resistance @ VREFH, VREFL 32 REG Load Regulation IOUT = 5mA step CAP Band Gap Bypass with 0.1µF 1 Logic 1 Input Voltage VSD = 5V 4 V VSD = 3.3V 2 V 14.85 14.95 V RL = 10Ω 100 140 mA VS+ is moved from 14V to 16V 45 65 dB 4 ms Code = 512 20 mV Code = 512 2 mV 2 mV/ms kΩ 0.5 1.5 mV/mA 1.3 1.6 V DIGITAL VIH FCLK Clock Frequency VIL Logic 0 Input Voltage tS Setup Time 20 ns tH Hold Time 20 ns tLC Load to Clock Time 20 ns tCE Clock to Load Line 20 ns tDCO Clock to Out Delay Time 10 ns RSDIN SDIN Input Resistance 1 GΩ TPULSE Minimum Pulse Width for EXT_OSC Signal 5 µs Duty Cycle Duty Cycle for EXT_OSC Signal 50 % INL Integral Nonlinearity Error 1.3 LSB DNL Differential Nonlinearity Error 0.5 LSB F_OSC Internal Refresh Oscillator Frequency 21 kHz 2 VSD = 3.3V/5V Negative edge of SCLK OSC_Select = 0 5 MHz 1 V FN7356.0 March 11, 2004 EL5225 Pin Descriptions PIN NUMBER PIN NAME PIN TYPE 1 ENA Logic Input Chip select, low enables data input to logic 2 SDI Logic Input Serial data input 3 SCLK Logic Input Serial data clock 4 SDO Logic Output Serial data output 5 EXT_OSC Logic Input/Output 6, 10 VS+ Analog Power NC PIN FUNCTION External oscillator input or internal oscillator output Positive supply voltage for analog circuits Not connected 7 VSD Digital Power 8 REFH Analog Reference Input High reference voltage 9 REFL Analog Reference Input Low reference voltage 11 GND Ground 12 CAP Analog Bypass Pin 13 OUTJ Analog Output Channel J programmable output voltage 14 OUTI Analog Output Channel I programmable output voltage 15 OUTH Analog Output Channel H programmable output voltage 17 OUTG Analog Output Channel G programmable output voltage 18 OUTF Analog Output Channel F programmable output voltage 19 OUTE Analog Output Channel E programmable output voltage 20 OUTD Analog Output Channel D programmable output voltage 22 OUTC Analog Output Channel C programmable output voltage 23 OUTB Analog Output Channel B programmable output voltage 24 OUTA Analog Output Channel A programmable output voltage OUTL Analog Output Channel L programmable output voltage OUTK Analog Output Channel K programmable output voltage GND Power 16, 21 3 Positive power supply for digital circuits (3.3V - 5V) Ground Decoupling capacitor for internal reference generator, 0.1µF Ground FN7356.0 March 11, 2004 EL5225 Typical Performance Curves DIFFERENTIAL NONLINEARITY (LSB) 0.3 1.5 0.2 REFH=13V REFL=2V 1 0.1 INL (LSB) 0 -0.1 0 VS=15V VSD=5V VREFH=13V VREFL=2V -0.2 -0.3 10 0.5 210 410 610 810 -0.5 -1 1010 0 200 400 INPUT CODE FIGURE 1. DIFFERENTIAL NONLINEARITY vs CODE 0mA 5mA/DIV 800 1000 1200 FIGURE 2. INTEGRAL NONLINEARITY ERROR 5mA 0mA 5mA CL=4.7nF RS=20Ω 5V CL=1nF RS=20Ω CL=4.7nF RS=20Ω 200mV/DIV 200mV/DIV CL=1nF RS=20Ω CL=180pF CL=180pF VS=VREFH=15V VS=VREFH=15V M=400ns/DIV M=400ns/DIV FIGURE 3. TRANSIENT LOAD REGULATION (SOURCING) SCLK 5V 0V SDA 5V FIGURE 4. TRANSIENT LOAD REGULATION (SINKING) SCLK 5V 0V SDA 5V 0V 0V 10V 10V 5V 0V 600 CODE OUTPUT 5V OUTPUT 0V M=400µs/DIV M=400µs/DIV FIGURE 5. LARGE SIGNAL RESPONSE (RISING FROM 0V TO 8V) FIGURE 6. LARGE SIGNAL RESPONSE (FALLING FROM 8V TO 0V) 4 FN7356.0 March 11, 2004 EL5225 Typical Performance Curves (Continued) SCLK SCLK 5V 5V 0V 0V SDA 5V 5V 0V 0V 200mV 200mV SDA OUTPUT OUTPUT 0V 0V M=400µs/DIV M=400µs/DIV FIGURE 7. SMALL SIGNAL RESPONSE (RISING FROM 0V TO 200mV) JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 0.9 1.2 1 θ TS JA = 0.8 SO 85 °C 0.6 P2 4 /W 0.4 0.2 0 JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 781mW 0.8 1.176W POWER DISSIPATION (W) POWER DISSIPATION (W) 1.4 FIGURE 8. SMALL SIGNAL RESPONSE (FALLING FROM 200mV TO 0V) 0.7 θ TS JA = 0.6 12 0.5 SO 8° P2 C/ 4 W 0.4 0.3 0.2 0.1 0 25 75 85 50 100 125 0 0 AMBIENT TEMPERATURE (°C) FIGURE 9. POWER DISSIPATION vs AMBIENT TEMPERATURE 25 50 75 85 100 125 AMBIENT TEMPERATURE (°C) FIGURE 10. POWER DISSIPATION vs AMBIENT TEMPERATURE General Description The EL5225 provides a versatile method of providing the reference voltages that are used in setting the transfer characteristics of LCD display panels. The V/T (Voltage/Transmission) curve of the LCD panel requires that a correction is applied to make it linear; however, if the panel is to be used in more than one application, the final curve may differ for different applications. By using the EL5225, the V/T curve can be changed to optimize its characteristics according to the required application of the display product. Each of the eight reference voltage outputs can be set with a 10-bit resolution. These outputs can be driven to within 50mV of the power rails of the EL5225. As all of the output buffers are identical, it is also possible to use the EL5225 for applications other than LCDs where multiple voltage references are required that can be set to 10 bit accuracy. 5 Digital Interface The EL5225 uses a simple 3-wire SPI compliant digital interface to program the outputs. The EL5225 can support the clock rate up to 5MHz. Serial Interface The EL5225 is programmed through a three-wire serial interface. The start and stop conditions are defined by the ENA signal. While the ENA is low, the data on the SDI (serial data input) pin is shifted into the 16-bit shift register on the positive edge of the SCLK (serial clock) signal. The MSB (bit 15) is loaded first and the LSB (bit 0) is loaded last (see Table 1). After the full 16-bit data has been loaded, the ENA is pulled high and the addressed output channel is updated. The SCLK is disabled internally when the ENA is high. The SCLK must be low before the ENA is pulled low. FN7356.0 March 11, 2004 EL5225 To facilitate the system designs that use multiple EL5225 chips, a buffered serial output of the shift register (SDO pin) is available. Data appears on the SDO pin at the 16th falling SCLK edge after being applied to the SDI pin. TABLE 1. CONTROL BITS LOGIC TABLE To control the multiple EL5225 chips from a single three-wire serial port, just connect the ENA pins and the SCLK pins together, connect the SDO pin to the SDI pin on the next chip. While the ENA is held low, the 16m-bit data is loaded to the SDI input of the first chip. The first 16-bit data will go to the last chip and the last 16-bit data will go to the first chip. While the ENA is held high, all addressed outputs will be updated simultaneously. The Serial Timing Diagram and parameters table show the timing requirements for three-wire signals. The serial data has a minimum length of 16 bits, the MSB (most significant bit) is the first bit in the signal. The bits are allocated to the following functions (also refer to the Control Bits Logic Table) • Bit 15 is always set to a zero • Bit 14 controls the source of the clock, see the next section for details • Bits 13 through 10 select the channel to be written to, these are binary coded with channel A = 0, and channel H=7 • The 10-bit data is on bits 9 through 0. Some examples of data words are shown in the table of Serial Programming Examples BIT NAME DESCRIPTION B15 Test B14 Oscillator B13 A3 Channel Address B12 A2 Channel Address B11 A1 Channel Address B10 A0 Channel Address B9 D9 Data B8 D8 Data B7 D7 Data B6 D6 Data B5 D5 Data B4 D4 Data B3 D3 Data B2 D2 Data B1 D1 Data B0 D0 Data Always 0 0 = Internal, 1 = External Serial Timing Diagram ENA tHE tSE T tr tf tHE tSE SCLK tSD tHD B15 SDI tw B14 B13 B12-B2 B1 B0 t MSB 6 Load MSB first, LSB last LSB FN7356.0 March 11, 2004 EL5225 TABLE 2. SERIAL TIMING PARAMETERS PARAMETER RECOMMENDED OPERATING RANGE DESCRIPTION T ≥200ns Clock Period tr/tf 0.05 * T Clock Rise/Fall Time tHE ≥10ns ENA Hold Time tSE ≥10ns ENA Setup Time tHD ≥10ns Data Hold Time tSD ≥10ns Data Setup Time tW 0.50 * T Clock Pulse Width TABLE 3. SERIAL PROGRAMMING EXAMPLES CONTROL CHANNEL ADDRESS DATA C1 C0 A3 A2 A1 A0 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Internal Oscillator, Channel A, Value = 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 Internal Oscillator, Channel A, Value = 1023 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 Internal Oscillator, Channel A, Value = 512 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 1‘t Internal Oscillator, Channel C, Value = 513 0 0 0 1 1 1 0 0 0 0 0 1 1 1 1 1 Internal Oscillator, Channel H, Value = 31 0 1 0 1 1 1 0 0 0 0 0 1 1 1 1 1 External Oscillator, Channel H, Value = 31 CONDITION Analog Section CLOCK OSCILLATOR TRANSFER FUNCTION The EL5225 requires an internal clock or external clock to refresh its outputs. The outputs are refreshed at the falling OSC clock edges. The output refreshed switches open at the rising edges of the OSC clock. The driving load shouldn’t be changed at the rising edges of the OSC clock. Otherwise, it will generate a voltage error at the outputs. This clock may be input or output via the clock pin labeled OSC. The internal clock is provided by an internal oscillator running at approximately 21kHz and can be output to the OSC pin. In a 2 chip system, if the driving loads are stable, one chip may be programmed to use the internal oscillator; then the OSC pin will output the clock from the internal oscillator. The second chip may have the OSC pin connected to this clock source. The transfer function is: data V OUT ( IDEAL ) = V REFL + ------------- × ( V REFH - V REFL ) 1024 where data is the decimal value of the 10-bit data binary input code. The output voltages from the EL5225 will be derived from the reference voltages present at the VREFL and VREFH pins. The impedance between those two pins is about 32kΩ. Care should be taken that the system design holds these two reference voltages within the limits of the power rails of the EL5225. GND < VREFH ≤ VS and GND ≤ VREFL ≤ VREFH. In some LCD applications that require more than 10 channels, the system can be designed such that one EL5225 will provide the Gamma correction voltages that are more positive than the VCOM potential. The second EL5225 can provide the Gamma correction voltage more negative than the VCOM potential. The Application Drawing shows a system connected in this way. 7 For transient load application, the external clock Mode should be used to ensure all functions are synchronized together. The positive edge of the external clock to the OSC pin should be timed to avoid the transient load effect. The Application Drawing shows the LCD H rate signal used, here the positive clock edge is timed to avoid the transient load of the column driver circuits. After power on, the chip will start with the internal oscillator mode. At this time, the OSC pin will be in a high impedance condition to prevent contention. By setting B14 to high, the chip is on external clock mode. Setting B14 to low, the chip is on internal clock mode. FN7356.0 March 11, 2004 EL5225 Block Diagram REFERENCE HIGH OUTA OUTB OUTH EIGHT CHANNEL MEMORY VOLTAGE SOURCES OUTI OUTJ REFERENCE LOW REFERENCE DECOUPLE CLK SDI FILTER CHANNEL OUTPUTS Each of the channel outputs has a rail-to-rail buffer. This enables all channels to have the capability to drive to within 50mV of the power rails, (see Electrical Characteristics for details). When driving large capacitive loads, a series resistor should be placed in series with the output. (Usually between 5Ω and 50Ω). Each of the channels is updated on a continuous cycle, the time for the new data to appear at a specific output will depend on the exact timing relationship of the incoming data to this cycle. The best-case scenario is when the data has just been captured and then passed on to the output stage immediately; this can be as short as 48µs. In the worst-case scenario, this will be 480µs when the data has just missed the cycle. When a large change in output voltage is required, the change will occur in 2V steps, thus the requisite number of timing cycles will be added to the overall update time. This means that a large change of 16V can take between 3.8ms 8 SDO CONTROL IF LOAD EXT_OSC and 4.2ms depending on the absolute timing relative to the update cycle. Output Stage and the Use of External Oscillator Simplified output sample and hold amp stage for one channel. CH 1.3V VIN + - + - S1 1.3V + - VOUT S2 OSC FIGURE 11. The output voltage is generated from the DAC, which is VIN at the above circuit. The refreshed switches are controlled by the internal or external oscillator signal. When the OSC clock signal is low, the switch S1 and S2 are closed. The output VOUT = VIN and at the same time the sample and hold cap CH is being charged. When the OSC clock signal is high, the refreshed switch S1 and S2 are opened and the output voltage is maintained by CH. This refreshed process FN7356.0 March 11, 2004 EL5225 will repeat every 10-clock cycles for each channel. The time takes to update the output depends on the timing at the VIN and the state of the switches. It can take 1 to 10 clock cycles to update each output. VOUT1 For the sample and hold capacitor CH to maintain the correct output voltage, the driving load shouldn’t be changed at the rising edge of the OSC signal. Since at the rising edge of the OSC clock, the refreshed switches are being opened, if the load changes at that time, it will generate an error output voltage. For a fixed load condition, the internal oscillator can be used. For the transient load condition, the external OSC mode should be used to avoid the conflict between the rising edge of the OSC signal and the changing load. So a timing delay circuit will be needed to delay the OSC signal and avoid the rising edge of the OSC signal and changing the load at the same time. OSC VOUT2 M=400µs/DIV FIGURE 13. CHANNEL-TO-CHANNEL REFRESH Ch1 - Output1 Ch3 - Output2 Ch2 - EXT_OSC At the falling edge of the OSC, output 1 is refreshing and one clock cycle later, output2 is being refreshed. The spike you see here is the response of the output amplifier when the refreshed switches are closed. When driving a big capacitor load, there will be ringing at the spikes because the phase margin of the amplifier is decreased. IOUT VOUT OSC M=400µs/DIV FIGURE 12. TRANSIENT LOAD RESPONSE Channel 3 - sinking and sourcing 5mA current Channel 2 - EXT_OSC signal Channel 1 - VOUT Here, the OSC signal is synchronized to the load signal. The rising edge of the OSC signal is then delayed by some amount of time and gives enough time for CH to be charged to a new voltage before the switches are opened. The speed of the external OSC signal shouldn’t be greater than 70kHz because for the worst condition, it will take at least 4µs to charge the sample and hold Capacitor CH. The pulse width has to be at least 4µs long. From our lab test, the duty cycle of the OSC signal must be greater than 30%. POWER DISSIPATION With the 30mA maximum continues output drive capability for each channel, it is possible to exceed the 125°C absolute maximum junction temperature. Therefore, it is important to calculate the maximum junction temperature for the application to determine if load conditions need to be modified for the part to remain in the safe operation. The maximum power dissipation allowed in a package is determined according to: T JMAX - T AMAX P DMAX = --------------------------------------------Θ JA where: • TJMAX = Maximum junction temperature • TAMAX = Maximum ambient temperature • θJA = Thermal resistance of the package • PDMAX = Maximum power dissipation in the package 9 FN7356.0 March 11, 2004 EL5225 The maximum power dissipation actually produced by the IC is the total quiescent supply current times the total power supply voltage and plus the power in the IC due to the loads. POWER SUPPLY BYPASSING AND PRINTED CIRCUIT BOARD LAYOUT Where: Good printed circuit board layout is necessary for optimum performance. A low impedance and clean analog ground plane should be used for the EL5225. The traces from the two ground pins to the ground plane must be very short. Lead length should be as short as possible and all power supply pins must be well bypassed. A 0.1µF ceramic capacitor must be place very close to the VS, VREFH, VREFL, and CAP pins. A 4.7µF local bypass tantalum capacitor should be placed to the VS, VREFH, and VREFL pins. • i = 1 to total 10 APPLICATION USING THE EL5225 • VS = Supply voltage In the first application drawing, the schematic shows the interconnect of a pair of EL5225 chips connected to give 10 gamma corrected voltages above the VCOM voltage, and 10 gamma corrected voltages below the VCOM voltage. P DMAX = V S × I S + Σ [ ( V S - V OUT i ) × I LOAD i ] when sourcing, and: P DMAX = V S × I S + Σ ( V OUT i × I LOAD i ) when sinking. • IS = Quiescent current • VOUTi = Output voltage of the i channel • ILOADi = Load current of the i channel By setting the two PDMAX equations equal to each other, we can solve for the RLOADs to avoid the device overheat. The package power dissipation curves provide a convenient way to see if the device will overheat. 10 FN7356.0 March 11, 2004 EL5225 Application Drawing +10V HIGH REFERENCE VOLTAGE REFH OUTA VS OUTB 0.1µF +12V COLUMN (SOURCE) DRIVER 0.1µF +5V MICROCONTROLLER VSD OUTC LCD PANEL 0.1µF OUTD LCD TIMING CONTROLLER SDI SCK ENA SDO HORIZONTAL RATE OUTE OSC CAP OUTF 0.1µF OUTI REFL GND OUTJ EL5225 MIDDLE REFERENCE VOLTAGE +5.5V +12V REFH OSC OUTA VS OUTB 0.1µF +5V VSD OUTC 0.1µF OUTD SDI SCK ENA CAP +1V 0.1µF LOW REFERENCE VOLTAGE OUTE OUTF REFL 0.1µF OUTI GND OUTJ EL5225 11 FN7356.0 March 11, 2004 EL5225 TSSOP Package Outline Drawing NOTE: The package drawing shown here may not be the latest version. To check the latest revision, please refer to the Intersil website at <http://www.intersil.com/design/packages/index.asp> All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 12 FN7356.0 March 11, 2004