Document 105-1 Chip Inductors – 1812CS (4532) • Higher SRF values than 1812 size parts with ferrite cores • 5% tolerances for all values • 19 inductance values from 1.0 to 33 µH Inductance2 Part number1 (µH) 1812CS-102XJL_ 1.0 @ 7.9 MHz 1812CS-122XJL_ 1.2 @ 7.9 MHz 1812CS-152X_L_ 1.5 @ 7.9 MHz 1812CS-182XJL_ 1.8 @ 7.9 MHz 1812CS-222X_L_ 2.2 @ 7.9 MHz 1812CS-272X_L_ 2.7 @ 7.9 MHz 1812CS-332X_L_ 3.3 @ 7.9 MHz 1812CS-392X_L_ 3.9 @ 7.9 MHz 1812CS-472XJL_ 4.7 @ 7.9 MHz 1812CS-562XJL_ 5.6 @ 7.9 MHz 1812CS-682XJL_ 6.8 @ 7.9 MHz 1812CS-822X_L_ 8.2 @ 7.9 MHz 1812CS-103XJL_ 10 @ 7.9 MHz 1812CS-123XJL_ 12 @ 2.5 MHz 1812CS-153X_L_ 15 @ 2.5 MHz 1812CS-183XJL_ 18 @ 2.5 MHz 1812CS-223X_L_ 22 @ 2.5 MHz 1812CS-273XJL_ 27 @ 2.5 MHz 1812CS-333X_L_ 33 @ 2.5 MHz Request free evaluation samples by contacting Coilcraft or visiting www.coilcraft.com. Percent SRF min5 DCR max6 Q min4 (MHz)(Ohms) 5 60 @ 50 MHz 310 1.2 5 62 @ 50 MHz 230 1.2 5,2 65 @ 50 MHz 210 1.6 5 68 @ 50 MHz 190 2.0 5,2 63 @ 50 MHz 170 2.2 5,2 63 @ 50 MHz 160 3.2 5,2 65 @ 50 MHz 145 3.8 5,2 69 @ 50 MHz 130 5.0 5 63 @ 50 MHz 115 5.4 5 59 @ 50 MHz 100 5.7 5 60 @ 50 MHz 90 6.6 5,2 47 @ 50 MHz 80 7.0 5 36 @ 50 MHz 70 7.7 5 35 @ 10 MHz 60 8.7 5,2 34 @ 10 MHz 50 9.6 5 30 @ 10 MHz 45 10.5 5,2 32 @ 10 MHz 40 11.5 5 29 @ 10 MHz 30 12.5 5,2 20 @ 10 MHz 20 13.5 tolerance3 1. When ordering, specify tolerance, termination and packaging codes: 1812CS-333XGLC Tolerance: G=2% J = 5% (Table shows stock tolerances in bold.) Termination:L=RoHS compliant silver-palladium-platinum-glass frit. E=Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:C =7″ machine-ready reel. EIA-481 embossed plastic tape (600 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (2200 parts per full reel). 2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Tolerances in bold are stocked for immediate shipment. 4. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test fixture. 5. SRF measured using an Agilent/HP 8753D network analyzer and a Coilcraft SMD-D test fixture. 6. DCR measured on a Cambridge Technology micro-ohmmeter and a Coilcraft CCF859 test fixture. 7. Current that causes a 15°C temperature rise from 25°C ambient. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Irms7 (mA) 480 480 430 380 340 300 270 240 230 220 210 200 190 180 170 160 155 150 145 Designer’s Kit C337 contains 10 of each 5% part Core material Ceramic Environmental RoHS compliant, halogen free optional Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 109 – 128 mg Ambient temperature –40°C to +125°C with Irms current, +125°C to +140°C with derated current Storage temperature Component: –40°C to +140°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +25 to +125 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 600 per 7″ reel; 2200 per 13″ reel. Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 3.7 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 105-1 Revised 01/11/12 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 105-2 Chip Inductors – 1812CS Series (4532) Typical Q vs Frequency Typical L vs Frequency 80 40 1.8 µH 33.0 µH 3.9 µH 70 30 Q Factor 50 Inductance (µH) 60 8.2 µH 40 30 15.0 µH 22.0 µH 22.0 µH 20 15.0 µH 8.2 µH 10 20 33.0 µH 3.9 µH 1.8 µH 10 0 0 1 10 1 100 Frequency (MHz) Irms Derating C D F 110 A H Pick and place material I G J F I 90 80 70 E terminal 60 50 Recommended Land Pattern Terminal wraparound: approx 0.015/0,38 both ends 40 ABCD maxmaxmax ref 30 0.1950.1500.1350.0700.1000.0250.1280.1200.0450.118inches 25°C Percent of rated Irms 100 1000 Frequency (MHz) B overall 120 100 10 20 0 20 G H IJ Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. 0 -20 F 4,953,813,431,782,540,643,253,051,143,00 mm 10 -40 E 40 60 80 100 120 140 Ambient temperature (°C) US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 105-2 Revised 01/11/12 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.