SOLID TANTALUM ELECTROLYTIC CAPACITORS F92 Resin-molded Chip, Compact Series Type numbering system (Example: 6.3V 10µF) 1 Compliant to the RoHS directive (2002/95/EC). 2 3 4 5 6 7 8 9 10 F 9 2 0 J 1 0 6 M P 11 Taping code (Refer to page 309 for details) Case code Capacitance tolerance Rated capacitance Rated voltage Series Drawing L W1 H W2 S Dimensions Marking Rated capacitance code P Case Rated capacitance (µF) A Case 22 10V Rated voltage (Voltage code) e G J 10V 16V 20V to Soldering Heat Iess than the initial specified value Leakage Current... Initial specified value or less Capacitance code of “P” case products are as shown below. Performance Characteristics P Case A • B Case Category Temperature Range Capacitance Tolerance Dissipation Factor (120Hz) ESR (100kHz) Capacitance Change... Refer to next page (∗ 1) Dissipation Factor...150% or Surge∗ – 55 to +125˚C (Rated temperature : 85˚C) less than the initial specified value ± 20% (at 120Hz) Refer to Next Page Refer to Next Page • After 1 minute's application of rated voltage, leakage current at 20˚C is not more than 0.01CV or 0.5µA, whichever is greater. • After 1 minute's application of rated voltage, leakage current Leakage Current at 85˚C is not more than 0.1CV or 5µA, whichever is greater. Endurance∗ • After 1 minute's application of derated voltage, leakage current at 125˚C is not more than 0.125CV or 6.3µA, whichever is greater. Damp Heat (Steady State) Temperature Cycles 0.22 0.33 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 Initial specified value or less Initial specified value or less Refer to next page (∗ Refer to next page (∗ Initial specified value or less After 2000hours' application of rated voltage in series with a 3Ω resistor at 85˚C, or derated voltage in series with a 3Ω resistor at 125˚C, capacitors meet the characteristic requirements listed below. Capacitance Change... Leakage Current... Initial specified value or less Refer to next page (∗ 1) Dissipation Factor... Initial specified value or less Leakage Current... Initial specified value or less After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no Shear Test electrode and has been soldered 5N (0.51kg • f) beforehand on an aluminum substrate, For 10 ± 1 seconds there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with a 20 specified jig at the center of the R230 Terminal Strength substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the 45 45 capacitor terminals. ∗ As for the surge and derated voltage at 125˚C, refer to page 308 for details. 1) Initial specified value or less Initial specified value or less 4 6.3 10 16 20 25 35 0J 1A 1C 1D 1E 1V A A A P P P P P P P P • A P P • A P • A (P) • A • B A • B A • B B (B) P P P A A • • • • • B P P P P P P P A A A B B P P P P • • • • P • B B P • A A P A A A A • A A (P) • A • B B A • B B B A A 1) Initial specified value or less 0G V Code 224 334 474 684 105 155 225 335 475 685 106 156 226 336 476 686 107 157 227 1) After 2000hours' application of rated voltage in series with a 3Ω resistor at 85˚C, or derated voltage in series with a 3Ω resistor at 125˚C, capacitors meet the characteristic requirements listed below. Capacitance Change... less than the initial specified value Standard Ratings Cap. (µF) Refer to next page (∗ Leakage Current... Initial specified value or less Refer to next page (∗ 1) Dissipation Factor...150% or +15% Max. (at +125˚C) +20% Max. (at +125˚C) +15% Max. (at +85˚C) +10% Max. (at +85˚C) --15% Max. (at --55˚C) --10% Max. (at --55˚C) At 40˚C 90 to 95% R.H. 500 hours (No voltage applied) At 40˚C 90 to 95% R.H. 500 hours (No voltage applied) ... Capacitance Change Refer to next page (∗ 1) Refer to next page (∗ 1) Dissipation Factor...150% or Iess than the initial specified value Initial specified value or less Leakage Current... Initial specified value or less Initial specified value or less --55˚C / +125˚C 30 minutes each 5 cycles Capacitance Change... Refer to next page (∗ 1) Dissipation Factor...150% or Iess than the initial specified value Leakage Current... Initial specified value or less (mm) S 0.5 ± 0.2 0.8 ± 0.2 0.8 ± 0.2 1mm Capacitance Change by Temperature H 1.1 ± 0.1 1.1 ± 0.1 1.1 ± 0.1 After application of surge voltage in series with a 33Ω (For “P” case : 1kΩ) resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C, capacitors meet the characteristics requirements listed below. Specifications Item W2 0.9 ± 0.1 1.2 ± 0.1 2.3 ± 0.1 Capacitance Change... Refer to next page (∗ 1) Dissipation Factor...150% of Resistance Rated voltage (V) E V L W1 2.0 ± 0.2 1.25 ± 0.1 3.2 ± 0.2 1.6 ± 0.2 3.4 ± 0.2 2.8 ± 0.2 10 seconds reflow at 260˚C, 5 seconds immension at 260˚C Rated capacitance (Capacitance code) 25V 35V A C D Case code P A B B Case G226 AS 2.5V 4V 6.3V S A A (P) • A A • • B B P • A A A • B B B A • B Capacitance code J N S W A E J N S w a e J n s ( ) The series in parentheses are being developed. Please contact to your local Nichicon sales office when these series are being designed in your application. CAT.8100Y SOLID TANTALUM ELECTROLYTIC CAPACITORS F92 Standard Ratings Rated Rated Volt Capacitance (µF) Case code Part Number Leakage Current (µA) Disspation *1 ESR ∆C/C Factor ( Ω@100kHz) (%@120Hz) (%) 3.3 4.7 6.8 10 10 15 22 22 33 33 47 47 68 68 100 100 150 P P P P A P P A P A A B A B A B B F920G335MPA F920G475MPA F920G685MPA F920G106MPA F920G106MAA F920G156MPA F920G226MPA F920G226MAA F920G336MPA F920G336MAA F920G476MAA F920G476MBA F920G686MAA F920G686MBA F920G107MAA F920G107MBA F920G157MBA 0.5 0.5 0.5 0.5 0.5 0.6 0.9 0.9 1.3 1.3 1.9 1.9 2.7 2.7 4.0 4.0 6.0 8 8 10 10 8 10 20 12 20 12 18 12 25 18 30 18 25 12.0 6.0 6.0 6.0 4.0 5.0 5.0 2.8 4.0 2.8 2.8 1.7 2.8 1.5 2.8 1.3 1.3 * * * * * * * * * * * * ±15 * ±15 * ±15 2.2 3.3 4.7 6.8 10 10 15 15 22 22 33 33 47 47 100 P P P P P A P A P A A B A B B F920J225MPA F920J335MPA F920J475MPA F920J685MPA F920J106MPA F920J106MAA F920J156MPA F920J156MAA F920J226MPA F920J226MAA F920J336MAA F920J336MBA F920J476MAA F920J476MBA F920J107MBA 0.5 0.5 0.5 0.5 0.6 0.6 0.9 0.9 1.4 1.4 2.1 2.1 3.0 3.0 6.3 8 8 8 10 10 8 10 8 20 12 12 12 18 12 20 12.0 12.0 6.0 6.0 6.0 4.0 6.0 4.0 5.0 2.8 2.8 1.7 2.8 1.7 1.3 * * * * * * * * * * * * ±15 * ±15 10V 1 1.5 2.2 3.3 3.3 4.7 4.7 6.8 6.8 10 10 15 22 22 33 47 P P P P A P A P A P A A A B B B F921A105MPA F921A155MPA F921A225MPA F921A335MPA F921A335MAA F921A475MPA F921A475MAA F921A685MPA F921A685MAA F921A106MPA F921A106MAA F921A156MAA F921A226MAA F921A226MBA F921A336MBA F921A476MBA 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.7 0.7 1.0 1.0 1.5 2.2 2.2 3.3 4.7 8 8 8 8 6 8 6 8 6 14 8 8 14 8 12 18 12.0 12.0 12.0 12.0 7.0 6.0 4.0 6.0 4.0 6.0 4.0 4.0 4.0 1.9 1.9 1.9 * * * * * * * * * * * * ±15 * * ±15 16V 0.47 0.68 1 1.5 2.2 2.2 3.3 4.7 4.7 6.8 10 10 22 P P P P P A A A B B A B B F921C474MPA F921C684MPA F921C105MPA F921C155MPA F921C225MPA F921C225MAA F921C335MAA F921C475MAA F921C475MBA F921C685MBA F921C106MAA F921C106MBA F921C226MBA 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.8 0.8 1.1 1.6 1.6 3.5 8 8 8 8 8 6 6 6 6 6 8 6 12 20.0 12.0 12.0 12.0 12.0 7.0 7.0 7.0 3.0 3.0 7.0 2.0 2.0 * * * * * * * * * * ±15 * ±15 4V 6.3V Rated Rated Volt Capacitance (µF) Leakage Current (µA) *1 Disspation ESR ∆C/C Factor ( Ω@100kHz) (%) (%@120Hz) Case code Part Number 20V 0.47 0.47 0.68 1 1 1.5 2.2 4.7 4.7 10 P A A P A A A A B B F921D474MPA F921D474MAA F921D684MAA F921D105MPA F921D105MAA F921D155MAA F921D225MAA F921D475MAA F921D475MBA F921D106MBA 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.9 0.9 2.0 8 4 4 8 4 6 6 10 6 8 20.0 10.0 10.0 20.0 10.0 7.4 7.0 7.0 3.0 3.0 * * * * * * * ±10 * ±10 25V 1 1 2.2 2.2 4.7 4.7 P A A B A B F921E105MPA F921E105MAA F921E225MAA F921E225MBA F921E475MAA F921E475MBA 0.5 0.5 0.6 0.6 1.2 1.2 8 6 8 6 10 6 20.0 10.0 10.0 4.0 7.0 3.0 * * ±15 * ±10 * 35V 0.22 0.33 0.47 1 2.2 3.3 A A A A B B F921V224MAA F921V334MAA F921V474MAA F921V105MAA F921V225MBA F921V335MBA 0.5 0.5 0.5 0.5 0.8 1.2 4 4 4 6 6 10 10.0 10.0 10.0 10.0 4.0 4.0 * * * * ±10 ±10 *1 : ∆C/C Item Damp Heat Tempereature cycles Resistance soldering heat Surge Endurance P Case (%) ±20 ±10 ±10 ±10 ±10 A , B Case(%) ±10 ± 5 ± 5 ± 5 ±10 CAT.8100Y