FAIRCHILD FMS6406

FMS6406
Precision S-Video Filter with Summed Composite
Output, Sound Trap, and Group Delay Compensation
Features
Description
■ 7.6MHz 5th-order Y,C filters with composite summer
The FMS6406 is a dual Y/C 5th-order Butterworth lowpass
video filter optimized for minimum overshoot and flat
group delay. The device also contains a summing circuit
to generate filtered composite video, an audio trap and
group delay compensation circuit. The audio trap removes
video information in the spectral location of the subsequent
RF audio carrier. The group delay circuit predistorts the
signal to compensate for the inherent receiver IF filter’s
group delay distortion.
■ 14dB notch at 4.425MHz to 4.6MHz for sound trap
■
■
■
■
■
■
■
■
■
■
■
capable of handling stereo
50dB stopband attenuation at 27MHz on Y, C,
and CV outputs
Better than 0.5dB flatness to 4.2MHz on Y, C,
and CV outputs
Equalizer and notch filter for driving RF modulator with
group delay of -180ns
No external frequency selection components or clocks
< 5ns group delay on Y, C, and CV outputs
AC coupled inputs
AC or DC coupled outputs
Capable of PAL frequency for Y, C, CV
Continuous Time Low Pass Filters
<1.4% differential gain with 0.7° differential phase on Y, C, and CV channels
Integrated DC restore circuitry with low tilt
In a typical application, the Y and C input signals from
DACs are AC-coupled into the filters. Both channels have
DC-restore circuitry to clamp the DC-input levels during
video sync. The Y and C channels use separate feedback
clamps. The clamp pulse is derived from the Y channel.
All outputs are capable of driving 2Vpp, AC or DC-coupled,
into either a single or dual video load. A single video load
consists of a series 75W impedance matching resistor
connected to a terminated 75W line, this presents a total
of 150W of loading to the part. A dual load would be two of
these in parallel which would present a total of 75W to the
part. The gain of the Y, C and CV signals is 6dB with 1Vpp
input levels. All video channels are clamped during sync
to establish the appropriate output voltage reference levels.
Applications
■ Cable set-top boxes
■ Satellite set-top boxes
■ DVD players
Block Diagram
VCC
7
Sync Strip
Reference
and Timing
YIN
1
6dB
gM
250mV
Σ
Notch
Group
Delay
250mV
CIN 4
YOUT
6
CV OUT
2
EQ_NOTCH
5
COUT
+
+
gM
8
6dB
3
GND
Ordering Information
Part Number
FMS6406CS
FMS6406CSX
© 2006 Fairchild Semiconductor Corporation
FMS6406 Rev. 4.0.4
Package
Pb-Free
Operating Temp
Range
Packaging
Method
SOIC-8
SOIC-8
Yes
Yes
0°C to +70°C
0°C to +70°C
Tube
Tape and Reel
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
August 2006
YIN
1
EQ_NOTCH
2
GND
3
CIN
4
FMS6406
8-pin
SOIC
© 2006 Fairchild Semiconductor Corporation
FMS6406 Rev. 4.0.4
8
YOUT
7
VCC
6
CVOUT
5
COUT
Pin Assignments
Pin#
Pin
Type
Description
1
YIN
Input
Luminance (Luma) Input: In a typical
system, this pin is connected to the
Luma or composite video output pin
from the external video encoder.
2
EQ_NOTCH
Output
3
GND
Input
Ground
4
CIN
Input
Chrominance (Chroma) Input: In a
typical system, this pin is connected
to the Chroma output pin from the
external video encoder.
5
COUT
Output
Filtered Chrominance Video Output
from the CIN channel.
6
CVOUT
Output
Composite Video Output: This pin is
the sum of YOUT and COUT.
7
VCC
Input
8
YOUT
Output
Composite video output to RF
modulator/driver.
+5V supply.
Filtered Luminance Video Output
from the YIN channel.
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
FMS6406 Pin Configuration
The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The
device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are
not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table defines the conditions for actual device operation.
Min.
Max.
Unit
VCC
Parameter
-0.3
6
V
Analog and Digital I/O
-0.3
VCC + 0.3
V
100
mA
Output Channel - Any One Channel (Do Not Exceed)
Notes:
Functional operation under any of these conditions is NOT implied. Performance and reliability are guaranteed only if operating conditions are not exceeded.
Reliability Information
Parameter
Min.
Typ.
Junction Temperature
Storage Temperature Range
-65
Lead Temperature (Soldering, 10s)
Thermal Resistance (qJA), JEDEC Standard Multi-layer
Test Boards, Still Air
Max.
Unit
150
°C
+150
°C
300
°C
115
°C/W
Recommended Operating Conditions
Parameter
Min
Operating Temperature Range
+4.75
GND
FMS6406 Rev. 4.0.4
Max
Unit
70
°C
+5.0
+5.25
V
0
VCC Range
© 2006 Fairchild Semiconductor Corporation
Typ
0
V
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Absolute Maximum Ratings
Tc = 25°C, Vi = 1Vpp, VCC = 5V, all inputs AC-coupled with 0.1μF, all outputs are AC-coupled with 220μF into
150Ω, referenced to 400kHz; unless otherwise noted.
Symbol Parameter
Conditions
ICC
Supply Current1
VCC no load
50
80
110
mA
AVYCCV
Low Frequency Gain (YOUT, COUT, CVOUT)
at 400kHz
5.8
6.0
6.2
dB
AVEQ
Low Frequency Gain (EQ_NOTCH)1
at 400kHz
5.7
6.0
6.4
dB
Csync
COUT Output Level (during Sync)
1
Sync present on YIN (after 6dB gain)
1.0
1.1
1.3
V
Ysync
YOUT Output Level (during Sync)1
Sync present on YIN (after 6dB gain)
0.35
0.5
V
CVsync
CVOUT Output Level (during Sync)
Sync present on YIN (after 6dB gain)
0.35
0.5
V
EQsync
EQ_NOTCH Output Level (during Sync)1
Sync present on YIN (after 6dB gain)
0.35
0.5
V
Settled to within 10mV
1
1
Min
Typ Max Units
TCLAMP
Clamp Response Time (Y Channel)
fFLAT
Gain Flatness to 4.2MHz2
(YOUT, COUT, CVOUT)
fC
-3dB Bandwidth1
fSB
Stopband Attenuation
(YOUT, COUT, CVOUT)
Vi
Input Signal Dynamic Range
All Channels/AC coupled
1.4
Vpp
ISC
Output Short Circuit Current4
(Any One Channel)
Y, C, CV, EQ_NOTCH to GND
85
mA
dG
Differential Gain2
Y, C, CV
1.4
3
dq
Differential Phase
Y, C, CV
0.7
1.5
THD
Output Distortion (All Channels)
VOUT = 1.8Vpp at 3.58MHz
0.3
%
XTALK
Crosstalk (Channel-to-Channel)
at 3.58MHz
-50
dB
PSRR
PSRR (All Channels)
DC
50
dB
SNR
SNR Y, C Channel
NTC-7 weighting 4.2MHz lowpass
70
75
dB
NTC-7 weighting 4.2MHz lowpass
70
75
dB
NTC-7 weighting 4.2MHz lowpass
65
70
dB
112
ns
1
2
2
SNR CV Channel2
SNR EQ_NOTCH Channel
2
5
ms
-0.5
0
0.5
dB
Y, C, CV Channels
6.7
7.6
MHz
at 27MHz
40
50
dB
%
°
tpd
Propagation Delay (Y, C, CV)
at 400kHz
GD
Group Delay (Y, C, CV)
at 3.58MHz (NTSC)
-5
0
5
ns
tSKEW
Skew Between YOUT and COUT2
at 1MHz
-2
0
2
ns
tCLGCV
Chroma-Luma Gain CVOUT1
f = 3.58MHz (ref to YIN at 400kHz)
98
100
102
%
tCLDCV
Chroma-Luma Delay CVOUT1
f = 3.58MHz (ref to YIN at 400kHz)
-10
0
10
ns
GDEQ
Group Delay EQ_NOTCH1
f = 3.58MHz (ref to YIN at 400kHz)
-195
-180
-165
ns
tCLGEQ
Chroma-Luma Gain EQ_NOTCH1
f = 3.58MHz (ref to YIN at 400kHz)
95
100
105
%
tCLDEQ
Chroma-Luma Delay EQ_NOTCH
f = 3.58MHz (ref to YIN at 400kHz)
-195
-180
-165
ns
dGEQ
Differential Gain2
0.3
1
%
dqEQ
Differential Phase
0.3
0.75
%
MCF
Modulator Channel Flatness1,3
EQ_NOTCH from 400kHz to 3.75MHz
-0.5
0
0.5
dB
AVPK
Gain Peaking1
EQ_NOTCH from >3.75MHz to 4.2MHz
-0.5
0
0.5
dB
Atten1
Notch Attenuation 11
EQ_NOTCH at 4.425MHz
14
dB
Atten2
Notch Attenuation 2
1
EQ_NOTCH at 4.5MHz
20
dB
Atten3
Notch Attenuation 31
EQ_NOTCH at 4.6MHz
14
dB
tPASS
Passband Group Delay, EQ_NOTCH
f = 400kHz to f = 3MHz
-35
2
1
EQ_NOTCH Channel
EQ_NOTCH Channel
2
1
35
ns
Notes:
1. 100% tested at 25°C.
2. Guaranteed by characterization.
3. Tested down to 400kHz, but guaranteed by design to 200kHz.
4. Sustained short circuit protection limited to 10 seconds.
© 2006 Fairchild Semiconductor Corporation
FMS6406 Rev. 4.0.4
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Electrical Characteristics
Tc = 25°C, Vi = 1Vpp, VCC = 5V, all inputs AC-coupled with 0.1μF, all outputs are AC-coupled with 220μF into
150Ω, referenced to 400kHz; unless otherwise noted.
10
140
120
12
0
Delay (ns)
Gain (dB)
-20
-30
-40
-50
Mkr Frequency
Ref 400kHz
1
2
3
Gain
6dB
6.53MHz
3
-1dB BW
7.87MHz
27MHz
-60
400kHz
5
10
15
1 = 8.2MHz (111.35ns)
20
25
0
400kHz
30
10
Delay (ns)
Mkr Frequency
Ref 400kHz
1
2
3
Gain
6dB
6.68MHz
3
-1dB BW
7.87MHz
27MHz
-60
400kHz
5
10
15
80
60
40
-3dB BW
-44.41dB
20
1 = 8.2MHz (111.16ns)
fSB = Gain(ref) – Gain(3) = 50.41dB
20
25
0
400kHz
30
5
10
Frequency (MHz)
20
25
30
Figure 4. Group Delay vs. Frequency COUT
10
140
0
120
12
1
100
Delay (ns)
-10
Gain (dB)
15
Frequency (MHz)
Figure 3. Frequency Response COUT
-20
Mkr Frequency
Gain
Ref 400kHz
6dB
1
2
3
6.53MHz
3
-1dB BW
7.72MHz
27MHz
-60
400kHz
5
10
15
60
20
1 = 8.2MHz (112.84ns)
20
25
0
400kHz
30
Frequency (MHz)
5
10
15
20
25
30
Frequency (MHz)
Figure 5. Frequency Response CVOUT
© 2006 Fairchild Semiconductor Corporation
80
40
-3dB BW
-43.49dB
fSB = Gain(ref) – Gain(3) = 49.49dB
FMS6406 Rev. 4.0.4
30
1
100
-20
-50
25
120
12
-10
-40
20
140
0
-30
15
Figure 2. Group Delay vs. Frequency YOUT
10
Gain (dB)
5
Frequency (MHz)
Figure 1. Frequency Response YOUT
-50
60
20
Frequency (MHz)
-40
80
40
-3dB BW
-44.66dB
fSB = Gain(ref) – Gain(3) = 50.66dB
-30
1
100
-10
Figure 6. Group Delay vs. Frequency CVOUT
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Typical Performance Characteristics
1500
10
5
0
-5
-10
-15
1
-20
-25
-30
-35
-40
-45
-50
1 = 4.425MHz (-16.00dB)
-55
400kHz
5
10
15
1000
1
500
Delay (ns)
Gain (dB)
Tc = 25°C, Vi = 1Vpp, VCC = 5V, HD/N_SD = 0, RSOURCE = 37.5Ω, all inputs AC-coupled with 0.1μF, all outputs
are AC-coupled with 220μF into 150Ω, referenced to 400kHz; unless otherwise noted.
0
-500
-1000
-1500
-2000
20
25
1 = 4.425MHz (198.47ns)
-2500
400kHz
30
5
10
Frequency (MHz)
Figure 7. Modulator vs. Frequency Response
0.2
NTSC
0.1
0
-0.1
30
NTSC
0.1
0
-0.2
Min = -0.19
Max = 0.16
ppMax = 0.34
-0.3
1st
2nd
Min = -0.17
Max = 0.07
ppMax = 0.25
-0.3
3rd
4th
5th
6th
1st
Figure 9. Differential Gain, MODOUT
2nd
3rd
4th
5th
6th
Figure 10. Differential Phase, MODOUT
-60
200
-65
150
-70
100
Delay (ns)
Noise (dB)
25
-0.1
-0.2
-75
-80
-85
Group Delay @ 3.58MHz = -178ns
50
0
-50
-90
-100
-95
-150
-200
-100
0
1
2
3
4
5
0
Frequency (MHz)
© 2006 Fairchild Semiconductor Corporation
1.0
2.0
3.0
4.0
4.6
Frequency (MHz)
Figure 11. Noise vs. Freq. Modulator Channel
FMS6406 Rev. 4.0.4
20
Figure 8. Delay Modulator Output
Differential Phase (deg)
Differential Gain (%)
0.2
15
Frequency (MHz)
Figure 12. Group Delay vs. Frequency
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Typical Performance Characteristics
Tc = 25°C, Vi = 1Vpp, VCC = 5V, HD/N_SD = 0, RSOURCE = 37.5Ω, all inputs AC-coupled with 0.1μF, all outputs
are AC-coupled with 220μF into 150Ω, referenced to 400kHz; unless otherwise noted.
1.5
Differential Gain (%)
0.8
Min = -0.00
Max = 1.17
ppMax = 1.16
NTSC
Differential Phase (deg)
2.0
1.0
0.5
0
-0.5
2nd
3rd
4th
5th
0.25
NTSC
Differential Phase (deg)
Differential Gain (%)
0.4
0.2
0
Min = -0.00
Max = 0.88
ppMax = 0.87
1st
2nd
3rd
4th
0.10
0.05
0
Min = -0.04
Max = 0.21
ppMax = 0.25
-0.10
4th
5th
6th
1st
1.5
2nd
3rd
4th
5th
6th
Figure 16. Differential Phase, COUT
0.5
Min = -0.00
Max = 1.42
ppMax = 1.40
NTSC
6th
NTSC
-0.05
3rd
5th
0.15
Differential Phase (deg)
Differential Gain (%)
2nd
0.20
Figure 15. Differential Gain, COUT
1.0
0.5
0
-0.5
0.4
0.3
NTSC
Min = -0.00
Max = 0.46
ppMax = 0.46
0.2
0.1
0
-0.1
1st
2nd
3rd
4th
5th
6th
1st
Figure 17. Differential Gain, CVOUT
© 2006 Fairchild Semiconductor Corporation
FMS6406 Rev. 4.0.4
0
Figure 14. Differential Phase, VOUT
0.8
2.0
0.2
1st
1.0
-0.4
0.4
6th
Figure 13. Differential Gain, VOUT
-0.2
0.6
-0.2
1st
1.2
Min = -0.01
Max = 0.59
ppMax = 0.60
NTSC
2nd
3rd
4th
5th
6th
Figure 18. Differential Phase, CVOUT
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Typical Performance Characteristics
-60
-50
-65
-55
-70
-60
-65
-75
Noise (dB)
Noise (dB)
Tc = 25°C, Vi = 1Vpp, VCC = 5V, HD/N_SD = 0, RSOURCE = 37.5Ω, all inputs AC-coupled with 0.1μF, all outputs
are AC-coupled with 220μF into 150Ω, referenced to 400kHz; unless otherwise noted.
-80
-85
-90
-95
-90
-100
-95
-100
-105
-110
-105
0
1.0
2.0
3.0
Frequency (MHz)
4.0
5.0
0
1.0
2.0
3.0
4.0
5.0
Frequency (MHz)
Figure 19. Noise vs. Frequency YOUT
Noise (dB)
-70
-75
-80
-85
Figure 20. Noise vs. Frequency COUT
-50
-55
-60
-65
-70
-75
-80
-85
-90
-95
-100
-105
-110
0
1.0
2.0
3.0
4.0
5.0
Frequency (MHz)
Figure 21. Noise vs. Frequency CVOUT
© 2006 Fairchild Semiconductor Corporation
FMS6406 Rev. 4.0.4
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Typical Performance Characteristics
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Typical Application Diagrams
4.5MHz FM Sound
FMS6406
Notch and
Group
Delay
YIN
1
2
+
Video
Modulator
8
5th-Order
Filter
+
YOUT
6
To TV
+
CIN
4
5
5th-Order
Filter
7
To Channel 3 or 4
CVOUT to VCR
3
5V
COUT
Figure 22. AC-Coupled Application Diagram
4.5MHz FM Sound
FMS6406
Notch and
Group
Delay
YIN
1
2
+
Video
Modulator
8
5th-Order
Filter
+
YOUT
6
To TV
+
CIN
4
5
5th-Order
Filter
7
To Channel 3 or 4
CVOUT to VCR
3
5V
COUT
Figure 23. DC-Coupled Application Diagram
© 2006 Fairchild Semiconductor Corporation
FMS6406 Rev. 4.0.4
www.fairchildsemi.com
Chrominance (C) I/O
Introduction
The chrominance input can be driven in the same manner
as the luminance input but is typically only a 0.7Vpp signal.
This product is a two channel monolithic continuous time
video filter designed for reconstructing the luminance and
chrominance signals from an S-Video D/A source.
Composite video output is generated by summing the Y
and C outputs. The chip is designed to have AC coupled
inputs and will work equally well with either AC or DC
coupled outputs.
The reconstruction filters provide a 5th-order Butterworth
response with group delay equalization. This provides a
maximally flat response in terms of delay and amplitude.
Each of the four outputs is capable of driving 2Vpp into a
75Ω load.
The composite video output driver is same as the other
outputs. When driving a dual load either output will still
function if the other output connection is inadvertently
shorted providing these loads are AC-coupled.
This output is designed to drive a 600Ω load to 2Vpp,
which will meet its primary intention of driving a modulator
load.
Layout Considerations
General layout and supply bypassing play major roles in
high-frequency performance and thermal characteristics.
The FMS6406DEMO is a 4-layer board with a full power
and ground plane. Following this layout configuration will
provide the optimum performance and thermal characteristics. For optimum results, follow the steps below as a
basis for high frequency layout:
In most applications the input coupling capacitors are
0.1μF. The Y and C inputs typically sink 1μA of current
during active video, which normally tilts a horizontal line
by 2mV at the Y output. During sync, the clamp restores
this leakage current by sourcing an average of 20μA over
the clamp interval. Any change in the coupling capacitor
values will affect the amount of tilt per line. Any reduction
in tilt will come with an increase in settling time.
■ Include 1µF and 0.1µF ceramic bypass capacitors
■ Place the 1µF capacitor within 0.75 inches of the
power pin
Luminance (Y) I/O
■ Place the 0.1µF capacitor within 0.1 inches of the
power pin
The typical luma input is driven by either a low impedance
source of 1Vpp or the output of a 75Ω terminated line
driven by the output of a current DAC. In either case, the
input must be capacitively coupled to allow the syncdetect and DC restore circuitry to operate properly.
■ For multi-layer boards, use a large ground plane to
help dissipate heat
■ For 2-layer boards, use a ground plane that extends
beyond the device by at least 0.5”
All outputs are capable of driving 2Vpp, AC or DC-coupled,
into either a single or dual video load. A single video load
consists of a series 75Ω impedance matching resistor
connected to a terminated 75Ω line, this presents a total
of 150Ω of loading to the part. A dual load would be two of
these in parallel which would present a total of 75Ω to the
part. The gain of the Y, C and CV signals is 6dB with 1Vpp
input levels. Even when two loads are present the driver
will produce a full 2Vpp signal at its output pin.
FMS6406 Rev. 4.0.4
Composite Video (CV) Output
Equalizer/Notch (EQ_NOTCH) Output
All channels are clamped during the sync interval to set the
appropriate minimum output DC level. With this operation
the effective input time constant is greatly reduced, which
allows for the use of small low cost coupling capacitors.
The net effect is that the input will settle to 10mV in 5ms
for any DC shifts present in the input video signal.
© 2006 Fairchild Semiconductor Corporation
Since the chrominance signal doesn’t contain any DC
content, the output signal can be AC coupled using as
small as a 0.1μF capacitor if DC-coupling is not desired.
■ Minimize all trace lengths to reduce series inductances
10
www.fairchildsemi.com
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Functional Description
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
Mechanical Dimensions
8-Lead Outline Package (SOIC)
© 2006 Fairchild Semiconductor Corporation
FMS6406 Rev. 4.0.4
11
www.fairchildsemi.com
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not
intended to be an exhaustive list of all such trademarks.
ACEx™
FAST®
ActiveArray™
FASTr™
FPS™
Bottomless™
Build it Now™
FRFET™
GlobalOptoisolator™
CoolFET™
CROSSVOLT™
GTO™
HiSeC™
DOME™
EcoSPARK™
I2C™
i-Lo™
E2CMOS™
EnSigna™
ImpliedDisconnect™
IntelliMAX™
FACT™
FACT Quiet Series™
Across the board. Around the world.™
The Power Franchise ®
Programmable Active Droop™
ISOPLANAR™
LittleFET™
MICROCOUPLER™
MicroFET™
MicroPak™
MICROWIRE™
MSX™
MSXPro™
OCX™
OCXPro™
OPTOLOGIC®
OPTOPLANAR™
PACMAN™
POP™
Power247™
PowerEdge™
PowerSaver™
PowerTrench®
QFET®
QS™
QT Optoelectronics™
Quiet Series™
RapidConfigure™
RapidConnect™
MSerDes™
ScalarPump™
SILENT SWITCHER®
SMART START™
SPM™
Stealth™
SuperFET™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SyncFET™
TCM™
TinyLogic®
TINYOPTO™
TruTranslation™
UHC™
UniFET™
UltraFET®
VCX™
Wire™
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY
PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN;
NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE
SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS,
SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR
CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body,
or (b) support or sustain life, or (c) whose failure to perform
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to
result in significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or In
Design
This datasheet contains the design specifications for
product development. Specifications may change in
any manner without notice.
P re l i m i n a r y
First Production
This datasheet contains preliminary data, and
supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
Obsolete
Not In Production
This datasheet contains specifications on a product
that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
Rev. I19
www.fairchildsemi.com
12
©2006 Fairchild Semiconductor Corporation
FMS6406 Precision S-Video Filter with Summed Composite Output, Sound Trap, and Group Delay Compensation
TRADEMARKS