Finisar Product Specification 4 Gigabit RoHS Compliant Long-Wavelength SFP Transceiver FTLF1324P2xTy PRODUCT FEATURES • Up to 4.25Gb/s bi-directional data links • Hot-pluggable SFP footprint • Built-in digital diagnostic functions • 1310nm Fabry-Perot laser transmitter • Duplex LC connector • RoHS compliant and Lead Free • Up to 4 km at 4.25 Gb/s and 10 km at ≤ 2.125 Gb/s on 9/125μm SMF • Metal enclosure, for lower EMI • Single 3.3V power supply • Industrial operating temperature range: -40°C to 85°C APPLICATIONS • Tri Rate 1.06 / 2.125 / 4.25 Gb/s Fibre Channel • 1.25Gb/s 1000Base-LX Ethernet and 1000Base-LX10 (Rate selectable version) Finisar’s FTLF1324P2xTy Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1. They are compatible with Fibre Channel FC-PI-2 10.02 standard for 4km distances at 4.25 Gb/s and 10km distances at 2.125 and 1.06 Gb/s. Rate selectable versions are also simultaneously compatible with Gigabit Ethernet 1000Base-LX as specified in IEEE Std 802.33 and 1000Base-LX10 as specified in IEEE Draft P802.3ah/D2.04. The product is RoHS compliant and lead-free per Directive 2002/95/EC5 and Finisar Application Note AN-2038. PRODUCT SELECTION FTLF1324P2xTy x y W B L V Wide Extraction Bail Narrow Extraction Bail Non Rate Selectable - 1x, 2x, 4x Fibre Channel Rate Selectable - 1x, 2x, 4x Fibre Channel and Gigabit Ethernet © Finisar Corporation August 31, 2006 Rev F Page 1 FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 I. Finisar Pin Descriptions Pin 1 2 3 4 5 6 7 Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select 8 9 10 11 12 13 14 15 16 17 18 19 20 LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Not supported. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. Open or Low = 1.063 Gb/s or 2.125 Gb/s Fibre Channel, 1.25 Gb/s Gigabit Ethernet (Low Bandwidth) High = 2.125 or 4.25 Gb/s Fibre Channel (High Bandwidth) Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. For Rate Selectable version only: In accordance with SFF Committee SFF-8079 Draft, Rev.1.6, Table 3. Note that rate select can also be set through 2-wire bus in accordance with SFF-84726 at Bit 3, Byte 110, Address A2h (note: writing ‘1’ selects full bandwidth operation). Rate select is the logic OR of the input state of Rate Select Pin and 2-wire bus. Non Rate Selectable version can operate at 1x, 2x, 4x Fibre Channel independent of rate select pin setting. 5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. 1 2 Towards Bezel TX Disable 4 MOD-DEF(2) 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 20 TXFault 3 5 VeeT TD- VeeT Towards ASIC VeeR Pinout of Connector Block on Host Board © Finisar Corporation August 31, 2006 Rev F Page 2 Finisar FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity III. Symbol Vcc TS Min -0.5 -40 TOP RH -40 0 Typ Max 4.2 85 Unit V °C 85 85 °C % Ref. 1 Electrical Characteristics (TOP = -40 to 85 °C, VCC = 3.00 to 3.60 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data output rise/fall time ≤ 2.125 Gb/s Data output rise/fall time = 4.25 Gb/s LOS Fault LOS Normal Power Supply Rejection Deterministic Jitter Contribution ≤ 2.125 Gb/s Total Jitter Contribution ≤ 2.125 Gb/s Deterministic Jitter Contribution = 4.25 Gb/s Total Jitter Contribution = 4.25 Gb/s Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr, tf tr, tf VLOS fault VLOS norm PSR RX Δ DJ Min 3.00 Typ 200 Max 3.60 300 Unit V mA Ref. 2 1200 Vcc Vee+ 0.8 10 Ω mV V V us 100 250 Vcc – 1.3 Vee 285 51.7 mV ps ps V V mVpp ps 4 5 5 6 6 7 8,9 RX Δ TJ RX Δ DJ 122.4 25.9 ps ps 9 8,10 RX Δ TJ 61.2 ps 10 Vcc – 0.5 Vee 100 400 800 175 120 VccHOST Vee+0.5 3 Notes: 1. Non condensing. 2. AC coupled. 3. Or open circuit. 4. Into 100 ohm differential termination. 5. 20 – 80 % 6. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA)1, September 14, 2000. 8. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ. 9. As measured at 0.022 mW OMA. 10. As measured at 0.048 mW OMA. © Finisar Corporation August 31, 2006 Rev F Page 3 Finisar FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 IV. Optical Characteristics (TOP = -40 to 85 °C, VCC = 3.00 to 3.60 Volts) Parameter Transmitter Output Opt. Power Optical Wavelength Spectral Width Optical Modulation Amplitude Optical Modulation Amplitude ≤ 2.125 Gb/s Optical Rise/Fall Time = 4.25 Gb/s Optical Rise/Fall Time ≤ 2.125 Gb/s RIN Deterministic Jitter Contribution = 4.25 Gb/s Total Jitter Contribution = 4.25 Gb/s Deterministic Jitter Contribution ≤ 2.125 Gb/s Total Jitter Contribution ≤ 2.125 Gb/s Optical Extinction Ratio = 1.25 Gb/s Receiver Receiver Sensitivity = 4.25 Gb/s Symbol POUT λ σ OMA OMA tr/ tf tr/ tf TX TX TX TX Δ Δ Δ Δ Min 1260 RSENS2 Receiver Sensitivity = 1.06 Gb/s RSENS1 Receiver Sensitivity = 1.25 Gb/s Stressed RX sens. = 1.25 Gb/s Receiver Overload Receiver Elec. 3 dB cutoff freq. Receiver Elec. 3 dB cutoff freq. Optical Center Wavelength Return Loss LOS De-Assert LOS Assert LOS Hysteresis RSENS1 LOSD LOSA -3 1350 Note 2 dBm nm 9 RxMAX λC Unit 90 160 -120 28.5 59.8 56.5 119 RSENSr Receiver Sensitivity = 2.125 Gb/s Max 190 174 DJ TJ DJ TJ ER Typ 1260 12 0.029 -18 0.015 -21 0.015 -22 -22 -14.5 0 1500 2500 1600 -19 -30 0.5 μW μW ps ps dB/Hz ps ps ps ps dB mW dBm mW dBm mW dBm dBm dBm dBm MHz MHz nm dB dBm dBm dB Ref. 1 2 2 2,3 2,3 4 5 6 6 7 8 9 8 9 8 9 10,11 11 12 Notes: 1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. Also specified to meet curves in FC-PI-2 10.0 Figures 18, 19, and 21, which allow trade-off between wavelength, spectral width and OMA. Rate selectable part is specified to meet IEEE Draft P802.3ah /D2.0 Figure 59-3. 3. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 4. Unfiltered, 20-80%. 5. Unfiltered, 20-80%. 6. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ. 7. Applicable for Rate Selectable version only in low bandwidth mode. 8. Measured with conformance signals defined in FC-PI-2 10.0 specifications. Value in OMA. Measured with PRBS 27-1 at 10-12 BER 9. Measured with conformance signals defined in FC-PI-2 10.0 specifications. Represents sensitivity based on OMA spec, as corrected to incoming Extinction Ratio of 13 dB (for example, at 5.75dB © Finisar Corporation August 31, 2006 Rev F Page 4 Finisar FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 incoming extinction ratio, an OMA of 0.029 mW corresponds to -16 dBm sensitivity). Measured with PRBS 27-1 at 10-12 BER . 10. Measured with PRBS 27-1 at 10-12 BER . 11. Rate Selectable version in low bandwidth mode. 12. Rate Selectable version in high bandwidth mode. V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125 μm SMF @ 4X Fibre Channel Max. Supported Link Length on 9/125μm SMF @ 1X and 2X Fibre Channel Max. Supported Link Length on 9/125μm SMF @ Gigabit Ethernet Symbol BR BER LMAX1 Min 1062 Typ Max 4250 10-12 4 Units Ref. Mb/sec 1 2 km 3 LMAX2 10 km 3 LMAX3 10 km 3 Notes: 1. Gigabit Ethernet and 1x/2x/4x Fibre Channel compliant. 2. Tested with a PRBS 27-1 test pattern. 3. Distances are based on FC-PI-2 10.0 and IEEE 802.3 standards. VI. Environmental Specifications Finisar 1310nm Industrial Temperature SFP transceivers have an operating temperature range from –40°C to +85°C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -40 -40 Typ Max 85 85 Units °C °C Ref. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. © Finisar Corporation August 31, 2006 Rev F Page 5 FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 Finisar VIII. Digital Diagnostic Functions Finisar FTLF1324P2xTy SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation1,6 or Finisar Application Note AN-2030. FTLF1324P2xTy transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. © Finisar Corporation August 31, 2006 Rev F Page 6 FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 IX. Finisar Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3. FTLF1324P2BTy © Finisar Corporation August 31, 2006 Rev F Page 7 FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 FTLF1324P2WTy © Finisar Corporation August 31, 2006 Rev F Page 8 Finisar FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 X. PCB Layout and Bezel Recommendations © Finisar Corporation August 31, 2006 Rev F Page 9 Finisar FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 © Finisar Corporation August 31, 2006 Rev F Page 10 Finisar FTLF1324P2xTy Industrial Temp. SFP Product Specification – August 2006 Finisar XI. References 1. Small Form-factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000. 2. “Fibre Channel Physical Interface Specification (FC-PI-2 10.0)”. American National Standard for Information Systems. 3. IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-LX. IEEE Standards Department, 2002. 4. IEEE Draft P802.3ah/D2.0, Clause 59, PMD Type 1000BASE-LX10. IEEE Standards Department, 2003. 5. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” January 27, 2003. 6. “Digital Diagnostics Monitoring Interface for Optical Transceivers”. SFF Document Number SFF-8472, Revision 9.3. XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation August 31, 2006 Rev F Page 11