ISSUED DATE :2006/04/18 REVISED DATE : G T 2 11 3 3 0 0 m A C M O S P o s i t i v e Vo l t a g e R e g u l a t o r Description The GT2113 series of positive, linear regulators feature low quiescent current (30 A typ.) with low dropout voltage, making them ideal for battery applications. The space-saving SOT-26 package is attractive for “Pocket” and “Hand Held” applications. This rugged device has both Thermal Shutdown, and Current Fold-back to prevent device failure under the “Worst” of operating conditions. An additional feature is a “Power Good” detector, which pulls low when the output is out of regulation. In applications requiring a low noise, regulated supply, place a 1000pF capacitor between Bypass and ground. The GT2113 is stable with an output capacitance of 2.2 F or greater. Features Very Low Dropout Voltage Guaranteed 300mA output Over-Temperature Shutdown Current Limiting Short Circuit Current Fold-back Typical Accurate± 1.5% Noise Reduction Bypass Capacitor Power-saving Shutdown Mode Power Good Detector Factory Pre-set Output Voltages Low Temperature coefficient Functional Block Diagram Applications Battery Powered Widgets Instrumentation Wireless Devices PC Peripherals Portable Electronics Cordless Phones Electronic Scales Package Dimensions REF. A B C D E F Millimeter Min. Max. 2.70 3.10 2.60 3.00 1.40 1.80 0.30 0.55 0 0.10 0° 10° REF. G H I J K L Dimensions Millimeter 1.90 REF. 1.20 REF. 0.12 REF. 0.37 REF. 0.60 REF. 0.95 REF. Typical Application Circuit 1/7 ISSUED DATE :2006/04/18 REVISED DATE : Absolute Maximum Ratings Parameter Input Max Voltage Output Current Output Voltage Operating Ambient Temperature Junction Temperature Maximum Junction Temperature Symbol Ratings Unit VIN IOUT VOUT Topr Tj Tj Max 8 PD/( VIN- VO) 1.5~5.0 -40 ~ +85 -40 ~ +125 150 81 260 400 B V mA V jc (Conductive Epoxy)* ja PD Thermal Resistance Internal Power Dissipation EDS Classification /W /W mW *Measure jc on center of molding compound if IC has no tab. Electrical Characteristics Ta=25 Parameter Output Voltage Symbol VOUT (E) Output Current Current Limit Load Regulation IO ILIM REGLOAD Dropout Voltage VDROPOUT Quiescent Current Ground Pin Current Line Regulation Input Voltage Over Temperature Shutdown Over Temperature Hysterisis Vo Temperature Coefficient Short Circuit Current(Note4) (Note1) IQ IGND REGLINE VIN OTS OTH TC ISC Power Supply Rejection PSRR Output Voltage Noise eN VEH VEL IEH IEL ISD VO,SD EN Input Threshold EN Input Bias Current Shutdown Supply Current Shutdown Output Voltage Output Under Voltage VUV Output Over Voltage VOV PG Leakage Current PG Voltage Rating PG Voltage Low ILC VPG VOL V N=VOUT(T)+2V unless otherwise noted Condition Min TYP Max Unit 1.5% V 1 1300 400 300 50 0.2 0.15 0.1 0.4 7 300 VIN 0.4 0.1 0.5 1 0.4 85 75 1 7 0.4 mA mA % VIN=VOUT(T)+2V, IO=1mA -1.5% VOUT(T) VIN=VOUT(T)+2V, VO>1.2 VIN=VOUT(T)+2V, VO>1.2 VIN=VOUT(T)+2V, IO=1mA to 300mA 1.2V VOUT(T) 2.0V IO=300mA VO=VOUT(E)-2% 2.0V<VOUT(T) 2.8V 2.8V<VOUT(T) VIN= VOUT(T)+1V, IO=0mA VIN= VOUT(T)+2V, IO=1mA~300mA 1.2V VOUT(T) 1.4V IO=1mA 1.4V<VOUT(T) 2.0V VIN=VOUT(T)+1 to 2.0V<VOUT(T)<4 VOUT(T)+2 4.0V VOUT(T) 300 300 -1 -0.2 -0.15 -0.1 -0.4 Note3 2.0 0 0 115 125 - 450 0.2 30 35 0.02 0.2 150 30 30 150 50 20 15 30 0.5 - VIN=VOUT(T)+1V, VO<0.8V f=1kHz Io=100mA f=10kHz Co=2.2 F f=100kHz f=10Hz~100kHz, Io=10mA, Co=2.2 F VIN=2.7V to 7V VIN=2.7V to 7V VEN=VIN, VIN=2.7V to 7V VEN= 0V, VIN=2.7V to 7V VIN=5V, VO=0V, VEN<VEL Io=0.4mA, VEN<VEL 2.5V VOUT(T) 5.0V 1.2V VOUT(T)<2.5V 2.5V VOUT(T) 5.0V 1.2V VOUT(T)<2.5V VPG=7V VO in regulation ISINK=0.4mA (Note2) mV A A % V ppm/ mA dB Vrms V V A A A V % VOUT(T) % VOUT(T) A V V Note 1: V OUT (E) =Effective Output Voltage (i.e. the output voltage when “VOUT (T) + 2.0V” is provided at the VIN pin while maintaining a certain IOUT value). 2: VOUT (T) =Specified Output Voltage 3: VIN (MIN) =VOUT+VDROPOUT 4: To prevent the Short Circuit Current protection feature from being prematurely activated, the input voltage must be applied before a current source load is applied. 2/7 ISSUED DATE :2006/04/18 REVISED DATE : Ordering Information ( contd. ) Part Number GT2113-15 GT2113-25 GT2113-28 GT2113-30 GT2113-33 GT2113-35 GT2113-37 GT2113-50 Marking 3A152 XXXX 3A252 XXXX 3A282 XXXX 3A302 XXXX 3A332 XXXX 3A352 XXXX 3A372 XXXX 3A502 XXXX Output Voltage Part Number 1.5V GT2113-18 2.5V GT2113-27 2.8V GT2113-29 3.0V GT2113-31 3.3V GT2113-34 3.5V GT2113-36 3.7V GT2113-38 5.0V GT2113-2H Marking 3A182 XXXX 3A272 XXXX 3A292 XXXX 3A312 XXXX 3A342 XXXX 3A362 XXXX 3A382 XXXX 3A2H2 XXXX Output Voltage 1.8V 2.7V 2.9V 3.1V 3.4V 3.6V 3.8V 2.85V Detailed Description The GT2113 family of COMS regulators contain a PMOS pass transistor, voltage reference, error amplifier, over-current protection, thermal shutdown and Power Good detection circuitry. The P-channel pass transistor receives data from the error amplifier, over-current shutdown, and thermal protection circuits. During normal operation, the error amplifier compares the output voltage to a precision reference. Over-current and Thermal shutdown circuits become active when the junction temperature exceeds 150 , or the current exceeds 300mA. During thermal shutdown, the output voltage remains low. Normal operation is restored when the junction temperature drops below 120 . The GT2113 switches from voltage mode to current mode when the load exceeds the rated output current. This prevents over-stress. The GT2113 also incorporates current fold-back to reduce power dissipation when the output is short circuited. This feature becomes active when the output drops below 0.8 volts, and reduces the current flow by 65%. Full current is restored when the voltage exceeds 0.8 volts. External Capacitors The GT2113 is stable with an output capacitance to ground of 2.2 F or greater. Ceramic capacitors have the lowest ESR, and will offer the best AC performance. Conversely, Aluminum Electrolytic capacitors exhibit the highest ESR, resulting in the poorest AC response. Unfortunately, large value ceramic capacitors are comparatively expensive. One option is to parallel a 0.1 F ceramic capacitor with a 10 F Aluminum Electrolytic. The benefit is low ESR, high capacitance, and low overall cost. A second capacitor is recommended between the input and ground to stabilize Vin. The input capacitor should be at least 0.1 F to have a beneficial effect. A third capacitor can be connected between the BY-Pass pin and Gnd. This capacitor can be a low cost Polyester Film variety between the value 0.001 ~ 0.01 F. A large capacitor improves the AC ripple rejection, but also makes the output come up slowly. This “Soft” turn-on is desirable in some applications to limit turn-on surges. All capacitors should be placed in close proximity to the pins. A “Quiet” ground termination is desirable. This can be achieved with a “Star” connection. Enable The Enable pin normally floats high. When actively, pulled low, the PMOS pass transistor shuts off, and all internal circuits are powered down. In this state, the quiescent current is less than 1 A. This pin behaves much like an electronic switch. Power Good The GT2113 includes the Power Good feature. When the output is not within ±15% of the specified voltage, it pulls low. This can occur under the following conditions: 1) Input Voltage too low. 2) During Over-Temperature. 3) During Over-Current. 4) If output is pulled up. (Note: PG pin is an open-drain output.) 3/7 ISSUED DATE :2006/04/18 REVISED DATE : Characteristics Curve 4/7 ISSUED DATE :2006/04/18 REVISED DATE : 5/7 ISSUED DATE :2006/04/18 REVISED DATE : 6/7 ISSUED DATE :2006/04/18 REVISED DATE : Important Notice: All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of GTM. GTM reserves the right to make changes to its products without notice. GTM semiconductor products are not warranted to be suitable for use in life-support Applications, or systems. GTM assumes no liability for any consequence of customer product design, infringement of patents, or application assistance. Head Office And Factory: Taiwan: No. 17-1 Tatung Rd. Fu Kou Hsin-Chu Industrial Park, Hsin-Chu, Taiwan, R. O. C. TEL : 886-3-597-7061 FAX : 886-3-597-9220, 597-0785 China: (201203) No.255, Jang-Jiang Tsai-Lueng RD. , Pu-Dung-Hsin District, Shang-Hai City, China TEL : 86-21-5895-7671 ~ 4 FAX : 86-21-38950165 7/7