FEATURES High Efficiency: 84% @ 1.5V/60A Size: 57.9 x 61.0 x 12.7mm (2.28” x 2.40” x 0.50”) Standard footprint Industry standard pin out Fixed frequency operation Metal baseplate Input UVLO, Output OCP, OVP, OTP Basic insulation No minimum load required 2:1 Input voltage range ISO 9001, TL 9000, ISO 14001, QS9000, OHSAS18001 certified manufacturing facility UL/cUL 60950 (US & Canada) Recognized, and TUV (EN60950) Certified CE mark meets 73/23/EEC and 93/68/EEC directives Delphi Series H48SL, 200W Half Brick Family DC/DC Power Modules: 48V in, 1.5V/60A out The Delphi Series H48SL Half Brick, 48V input, single output, isolated OPTIONS DC/DC converters are the latest offering from a world leader in power Positive Remote On/Off logic systems technology and manufacturing ― Delta Electronics, Inc. This Negative trim product family provides up to 200 watts of power (3.3V and above) or Short pin lengths 60A of output current in an industry standard footprint. With creative design technology and optimization of component placement, these converters possess outstanding electrical and thermal performance, as well as extremely high reliability under highly stressful operating conditions. All models are fully protected from abnormal input/output APPLICATIONS voltage, current, and temperature conditions. The Delphi Series Telecom/Datacom converters meet all safety requirements with basic insulation. Wireless Networks Optical Network Equipment Server and Data Storage Industrial/Test Equipment DATASHEET DS_H48SL1R560_10302006 TECHNICAL SPECIFICATIONS (TA=25°C, airflow rate=300 LFM, Vin=48Vdc, nominal Vout unless otherwise noted) PARAMETER NOTES and CONDITIONS H48SL1R560 (Standard) Min. ABSOLUTE MAXIMUM RATINGS Input Voltage Continuous Transient (100ms) Operating Case Temperature Storage Temperature Input/Output Isolation Voltage INPUT CHARACTERISTICS Operating Input Voltage Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Lockout Hysteresis Voltage Maximum Input Current No-Load Input Current Off Converter Input Current Inrush Current(I2t) Input Reflected-Ripple Current Input Voltage Ripple Rejection OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Load Over Line Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception DYNAMIC CHARACTERISTICS Output Voltage Current Transient Positive Step Change in Output Current Negative Step Change in Output Current Settling Time (within 1% Vout nominal) Turn-On Transient Start-Up Time, From On/Off Control Start-Up Time, From Input Maximum Output Capacitance EFFICIENCY 100% Load 60% Load ISOLATION CHARACTERISTICS Input to Output Input to Case Output to Case Isolation Resistance Isolation Capacitance FEATURE CHARACTERISTICS Switching Frequency ON/OFF Control, Negative Remote On/Off logic Logic Low (Module On) Logic High (Module Off) ON/OFF Control, Positive Remote On/Off logic Logic Low (Module Off) Logic High (Module On) ON/OFF Current (for Both Remote on/off logic) Leakage Current (for Both Remote on/off logic) Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection GENERAL SPECIFICATIONS MTBF Weight Over-Temperature Shutdown DS_H48SL1R560_10302006 100ms Tc 1 minute Typ. -40 -55 1500 Output Voltage 10% Low 80 100 +100 +125 Vdc Vdc °C °C Vdc 48 75 Vdc 33 31 1 34 32 2 35 33 3 3.6 150 10 Vdc Vdc Vdc A mA mA A2s mA dB 1.5 1.53 Vdc ±2 ±2 ±15 ±5 ±5 ±50 1.57 mV mV mV V 75 25 150 40 60 150 mV mV A % 60 3 0.03 25 65 P-P thru 12µH inductor, 5Hz to 20MHz 120 Hz Io=Io,min to Io,max Vin=36V to 75V Tc=-40℃ to 100℃ over sample load, line and temperature 5Hz to 20MHz bandwidth Full Load, 1µF ceramic, 10µF tantalum Full Load, 1µF ceramic, 10µF tantalum Units 36 100% Load, 36Vin Vin=48V, Io=Io.max, Tc=25℃ Max. 1.47 1.43 0 110 48V, 10µF Tan & 1µF Ceramic load cap, 0.1A/µs 50% Io.max to 75% Io.max 75% Io.max to 50% Io.max 80 80 100 10 10 Full load; 5% overshoot of Vout at startup mV mV us 20 20 20000 84 87 % % 1300 Vdc Vdc Vdc MΩ pF 180 kHz 1500 1500 500 10 Von/off at Ion/off=1.0mA Von/off at Ion/off=0.0 µA Von/off at Ion/off=1.0mA Von/off at Ion/off=0.0 µA Ion/off at Von/off=0.0V Logic High, Von/off=15V Across Pins 9 & 5, Pout ≦ max rated power Pout ≦ max rated power Over full temp range; % of nominal Vout Io=80% of Io, max; Ta=25°C Average PCB Temperature ms ms µF 0 0.8 15 V V 0 0.4 15 1 50 +10 10 130 V V mA uA % % % -20 115 122 2.23 85 110 M hours grams °C 2 ELECTRICAL CHARACTERISTICS CURVES 90 20.0 85 48Vin 75Vin 16.0 POWER DISSIPATION (W) EFFICIENCY (%) 36Vin 80 75 70 12.0 8.0 4.0 36Vin 48Vin 75Vin 65 0.0 10 20 30 40 50 60 10 20 30 40 50 60 OUTPUT CURRENT(A) OUTPUT CURRENT (A) Figure 1: Efficiency vs. load current for minimum, nominal, and maximum input voltage at 25°C. Figure 2: Power dissipation vs. load current for minimum, nominal, and maximum input voltage at 25°C. 3.5 INPUT CURRENT (A) Io=60A Io=36A Io=6A 3.0 2.5 2.0 1.5 1.0 0.5 0.0 30 35 40 45 50 55 60 65 70 75 INPUT VOLTAGE (V) Figure 3: Typical input characteristics at room temperature DS_H48SL1R560_10302006 3 ELECTRICAL CHARACTERISTICS CURVES For Negative Remote On/Off Logic Figure 4: Turn-on transient at full rated load current (resistive load) (2 ms/div). Top Trace: Vout; 500mV/div; Bottom Trace: ON/OFF input: 10V/div Figure 5: Turn-on transient at zero load current (2 ms/div). Top Trace: Vout: 500mV/div; Bottom Trace: ON/OFF input: 10V/div For Positive Remote On/Off Logic Figure 6: Turn-on transient at full rated load current (resistive load) (2 ms/div). Top Trace: Vout; 500mV/div; Bottom Trace: ON/OFF input: 2V/div DS_H48SL1R560_10302006 Figure 7: Turn-on transient at zero load current (2 ms/div). Top Trace: Vout: 500mV/div; Bottom Trace: ON/OFF input: 2V/div 4 ELECTRICAL CHARACTERISTICS CURVES Figure 8: Output voltage response to step-change in load current (75%-50%-75% of Io, max; di/dt = 0.1A/µs). Load cap: 10µF, tantalum capacitor and 1µF ceramic capacitor. Top Trace: Vout (100mV/div), Bottom Trace: Iout (10A/div). Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. Figure 9: Output voltage response to step-change in load current (75%-50%-75% of Io, max; di/dt = 2.5A/µs). Load cap: 470µF, 35mΩ ESR solid electrolytic capacitor and 1µF ceramic capacitor. Top Trace: Vout (100mV/div), Bottom Trace: Iout (10A/div). Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. Figure 10: Test set-up diagram showing measurement points for Input Terminal Ripple Current and Input Reflected Ripple Current. Note: Measured input reflected-ripple current with a simulated source Inductance (LTEST) of 12 µH. Capacitor Cs offset possible battery impedance. Measure current as shown above. DS_H48SL1R560_10302006 5 ELECTRICAL CHARACTERISTICS CURVES Figure 11: Input Terminal Ripple Current, ic, at full rated output current and nominal input voltage with 12µH source impedance and 33µF electrolytic capacitor (1A/div). Figure 12: Input reflected ripple current, is, through a 12µH source inductor at nominal input voltage and rated load current (20 mA/div). Copper Strip Vo(+) 10u 1u SCOPE RESISTIVE LOAD Vo(-) Figure 13: Output voltage noise and ripple measurement test setup DS_H48SL1R560_10302006 6 ELECTRICAL CHARACTERISTICS CURVES 1.6 1.4 OUTPUT VOLTAGE (V) 1.2 1.0 0.8 0.6 0.4 48Vin 0.2 0.0 0 10 20 30 40 50 60 70 80 90 100 LOAD CURRENT (A) Figure 14: Output voltage ripple at nominal input voltage and rated load current (20 mV/div). Load capacitance: 1µF ceramic capacitor and 10µF tantalum capacitor. Bandwidth: 20 MHz. Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. DS_H48SL1R560_10302006 Figure 15: Output voltage vs. load current showing typical current limit curves and converter shutdown points. 7 THERMAL CURVES: NO HEATSINK, EITHER ORIENTATION ) m" 2 m0 . 61 2 ( 64 H48SL1R560(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin < 60V (Either Orientation, no Heat sink) Output Current(A) 600LFM 56 m m 7 2 ) " 6 0 . 1 ( 500LFM out 48 40 Sense On/Off 32 Trim 100LFM 24 Sense(-) Case 400LFM Natural Convection 200LFM 16 out 300LFM 8 0 0 Figure 16: Case temperature measurement location. Pin locations are for reference only. 20 30 40 50 60 70 Output Current(A) 21 90 100 Ambient Temperature (℃) H48SL1R560(Standard) Power Dissipation vs. Ambient Temperature and Air Velocity (Either Orientation, no Heat sink) Power Dissipation (Watts) 600LFM 600LFM 56 80 Figure 17: Output current vs. ambient temperature and air velocity (Vin<60V) H48SL1R560(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 75V (Either Orientation, no Heat sink) 64 10 18 48 500LFM 40 Natural Convection 400LFM 500LFM 15 12 400LFM Natural Convection 32 100LFM 9 24 100LFM 200LFM 6 200LFM 16 300LFM 300LFM 3 8 0 0 0 10 20 30 40 50 60 70 80 90 100 Ambient Temperature (℃) Figure 18: Output current vs. ambient temperature and air velocity (Vin=75V) DS_H48SL1R560_10302006 0 10 20 30 40 50 60 70 80 90 100 Ambient Temperature (℃) Figure 19: Power dissipation vs. ambient temperature and air velocity 8 DESIGN CONSIDERATIONS Input Source Impedance The impedance of the input source connecting to the DC/DC power modules will interact with the modules and affect the stability. A low ac-impedance input source is recommended. If the source inductance is more than a few µH, we advise adding a 10 to 100 µF electrolytic capacitor (ESR < 0.7 Ω at 100 kHz) mounted close to the input of the module to improve the stability. Layout and EMC Considerations Delta’s DC/DC power modules are designed to operate in a wide variety of systems and applications. For design assistance with EMC compliance and related PWB layout issues, please contact Delta’s technical support team. An external input filter module is available for easier EMC compliance design. Application notes to assist designers in addressing these issues are pending release. Safety Considerations The power module must be installed in compliance with the spacing and separation requirements of the end-user’s safety agency standard, i.e., UL60950, CAN/CSA-C22.2 No. 60950-00 and EN60950:2000 and IEC60950-1999, if the system in which the power module is to be used must meet safety agency requirements. Basic insulation based on 75 Vdc input is provided between the input and output of the module for the purpose of applying insulation requirements when the input to this DC-to-DC converter is identified as TNV-2 or SELV. An additional evaluation is needed if the source is other than TNV-2 or SELV. When the input source is 60 Vdc or below, the power module meets SELV (safety extra-low voltage) requirements. If the input source is a hazardous voltage which is greater than 60 Vdc and less than or equal to 75 Vdc, for the module’s output to meet SELV requirements, all of the following must be met: DS_H48SL1R560_10302006 The input source must be insulated from the ac mains by reinforced or double insulation. The input terminals of the module are not operator accessible. If the metal baseplate is grounded, one Vi pin and one Vo pin shall also be grounded. A SELV reliability test is conducted on the system where the module is used, in combination with the module, to ensure that under a single fault, hazardous voltage does not appear at the module’s output. When installed into a Class II equipment (without grounding), spacing consideration should be given to the end-use installation, as the spacing between the module and mounting surface have not been evaluated. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. This power module is not internally fused. To achieve optimum safety and system protection, an input line fuse is highly recommended. The safety agencies require a normal-blow fuse with 20A maximum rating to be installed in the ungrounded lead. A lower rated fuse can be used based on the maximum inrush transient energy and maximum input current. Soldering and Cleaning Considerations Post solder cleaning is usually the final board assembly process before the board or system undergoes electrical testing. Inadequate cleaning and/or drying may lower the reliability of a power module and severely affect the finished circuit board assembly test. Adequate cleaning and/or drying is especially important for un-encapsulated and/or open frame type power modules. For assistance on appropriate soldering and cleaning procedures, please contact Delta’s technical support team. 9 FEATURES DESCRIPTIONS Vi(+) Over-Current Protection Sense(+) The modules include an internal output over-current protection circuit, which will endure current limiting for an unlimited duration during output overload. If the output current exceeds the OCP set point, the modules will automatically shut down (hiccup mode). The modules will try to restart after shutdown. If the overload condition still exists, the module will shut down again. This restart trial will continue until the overload condition is corrected. Over-Voltage Protection The modules include an internal output over-voltage protection circuit, which monitors the voltage on the output terminals. If this voltage exceeds the over-voltage set point, the module will shut down and latch off. The over-voltage latch is reset by either cycling the input power or by toggling the on/off signal for one second. Over-Temperature Protection ON/OFF Sense(-) Vi(-) Remote Sense Remote sense compensates for voltage drops on the output by sensing the actual output voltage at the point of load. The voltage between the remote sense pins and the output terminals must not exceed the output voltage sense range given here: [Vo(+) – Vo(–)] – [SENSE(+) – SENSE(–)] ≤ 10% × Vout This limit includes any increase in voltage due to remote sense compensation and output voltage set point adjustment (trim). Vi(+) Vo(+) Sense(+) The module will try to restart after shutdown. If the over-temperature condition still exists during restart, the module will shut down again. This restart trial will continue until the temperature is within specification. The remote on/off feature on the module can be either negative or positive logic. Negative logic turns the module on during a logic low and off during a logic high. Positive logic turns the modules on during a logic high and off during a logic low. Remote on/off can be controlled by an external switch between the on/off terminal and the Vi(-) terminal. The switch may be an open collector or open drain. For negative logic if the remote on/off feature is not used, please short the on/off pin to Vi(-). For positive logic if the remote on/off feature is not used, please leave the on/off pin floating. Vo(-) Figure 20: Remote on/off implementation The over-temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the over-temperature threshold the module will shut down. Remote On/Off Vo(+) Sense(-) Contact Resistance Vi(-) Vo(-) Contact and Distribution Losses Figure 21: Effective circuit configuration for remote sense operation If the remote sense feature is not used to regulate the output at the point of load, please connect SENSE(+) to Vo(+) and SENSE(–) to Vo(–) at the module. The output voltage may be increased by both the remote sense and the trim; however, the maximum increase is the larger of either the remote sense or the trim, not the sum of both. When using remote sense and trim, the output voltage of the module is usually increased, which increases the power output of the module with the same output current. Care should be taken to ensure that the maximum output power does not exceed the maximum rated power. DS_H48SL1R560_10302006 10 FEATURES DESCRIPTIONS (CON.) Output Voltage Adjustment (TRIM) To increase or decrease the output voltage set point, connect an external resistor between the TRIM pin and either the SENSE(+) or SENSE(-). The TRIM pin should be left open if this feature is not used. Figure 23: Circuit configuration for trim-up (increase output voltage) Figure 22: Circuit configuration for trim-down (decrease output voltage) If the external resistor is connected between the TRIM and SENSE (-) pins, the output voltage set point decreases.(Fig. 22) The external resistor value required to obtain a percentage of output voltage change △% is defined as: 100 Rtrim down= ⎛⎜ − 2⎞ ΚΩ ∆% ⎝ ⎠ Ex. When Trim-down -20%(1.5V×0.8=1.2V) Vo := 1.5 V 100 ∆ ∆ := 20 − 2 = 3 KΩ If the external resistor is connected between the TRIM and SENSE (+) the output voltage set point increases (Fig. 23). The external resistor value required to obtain a percentage output voltage change △% is defined as: Rtrim up= ⎡⎢ Vo⋅ ( 100 + ∆%) ⎣ 1.225⋅ ∆% − 100 + 2∆%⎤ ∆% ⎥ ΚΩ ⎦ Ex. When Trim-up +10%(1.5V×1.1=1.65V) Vo := 1.5V Vo⋅ ( 100 + ∆ ) 1.225⋅ ∆ ∆ := 10 − 100 + 2⋅ ∆ ∆ = 1.469 KΩ The output voltage can be increased by both the remote sense and the trim, however the maximum increase is the larger of either the remote sense or the trim, not the sum of both. When using remote sense and trim, the output voltage of the module is usually increased, which increases the power output of the module with the same output current. Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power. DS_H48SL1R560_10302006 11 THERMAL CONSIDERATIONS Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode of heat transfer. Hence, the choice of equipment to characterize the thermal performance of the power module is a wind tunnel. Thermal Derating Heat may be removed by increasing airflow over the module. The module’s maximum case temperature is +100°C. To enhance system reliability, the power module should always be operated below the maximum operating temperature. If the temperature exceeds the maximum module temperature, reliability of the unit may be affected. Thermal Testing Setup Delta’s DC/DC power modules are characterized in heated vertical wind tunnels that simulate the thermal environments encountered in most electronics equipment. This type of equipment commonly uses vertically mounted circuit cards in cabinet racks in which the power modules are mounted. The following figure shows the wind tunnel characterization setup. The power module is mounted on a test PWB and is vertically positioned within the wind tunnel. The space between the neighboring PWB and the top of the power module is constantly kept at 6.35mm (0.25’’). PWB FACING PWB MODULE AIR VELOCITY AND AMBIENT TEMPERATURE MEASURED BELOW THE MODULE 50.8 (2.0”) AIR FLOW 12.7 (0.5”) Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches) Figure 24: Wind tunnel test setup DS_H48SL1R560_10302006 12 MECHANICAL DRAWING Pin No. 1 2 3 4 5 6 7 8 9 Name Function -Vin Case ON/OFF +Vin +Vout +SENSE TRIM -SENSE -Vout Negative input voltage Case ground Remote ON/OFF Positive input voltage Positive output voltage Positive remote sense Output voltage trim Negative remote sense Negative output voltage Pin Specification: Pins 1-4, 6-8 Pins 5 & 9 1.00mm (0.040”) diameter 2.00mm (0.079”) diameter All pins are copper with Tin plating. DS_H48SL1R560_10302006 13 PART NUMBERING SYSTEM H 48 Form Factor H – Half-Brick S Input Number of Voltage Outputs 48V S - Single L 1R5 60 N R Product Series Output Voltage Output Current ON/OFF Logic Pin Length L - IMS, positive trim 1R5 - 1.5V 60 - 60A N - Negative P - Positive R - 0.170” N - 0.145” K - 0.110” F A Option Code F- RoHS 6/6 Lead Free) A - Standard Functions MODEL LIST MODEL NAME INPUT OUTPUT EFF @ 100% LOAD H48SL1R560NRFA 36V~75V 3.6A 1.5V 60A 84% H48SL1R860NRFA 36V~75V 4.3A 1.8V 60A 85% H48SL2R560NRFA 36V~75V 5.7A 2.5V 60A 88% H48SL3R360NRFA 36V~75V 7.4A 3.3V 60A 89% H48SL05040NRFA 36V~75V 7.4A 5V 40A 90.5% H48SL12020NRFA 36V~75V 8.7A 12V 20A 91% Default remote on/off logic is negative and pin length is 0.170” For different remote on/off logic and pin length, please refer to part numbering system above or contact your local sales office. CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: [email protected] Europe: Telephone: +41 31 998 53 11 Fax: +41 31 998 53 53 Email: [email protected] Asia & the rest of world: Telephone: +886 3 4526107 x6220 Fax: +886 3 4513485 Email: [email protected] WARRANTY Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon request from Delta. Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these specifications at any time, without notice. DS_H48SL1R560_10302006 14