PANJIT 1SMC5369

1SMC5348 THRU 1SMC5388
SURFACE MOUNT SILICON ZENER DIODE
VOLTAGE - 11 TO 200 Volts
Power - 5.0 Watts
FEATURES
l For surface mounted applications in order to
optimize board space
l Low profile package
l Built-in strain relief
l
l
l
Glass passivated junction
Low inductance
Typical ID less than 1 £gA above 13V
l
High temperature soldering :
260 ¢J /10 seconds at terminals
l
Plastic package has Underwriters Laboratory
DO-214AB
Flammability Classification 94V-O
MECHANICAL DATA
Case: JEDEC DO-214AB Molded plastic
over passivated junction
Terminals: Solder plated, solderable per
MIL-STD-750, method 2026
Standard Packaging: 16mm tape(EIA-481)
Weight: 0.007 ounce, 0.21 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ¢J ambient temperature unless otherwise specified.
SYMBOL
DC Power Dissipation @ TL=75 ¢J , Measure at Zero Lead Length(Fig. 1)
PD
Derate above 75 ¢J (Note 1)
Peak forward Surge Current 8.3ms single half sine-wave superimposed on rated
IFSM
load(JEDEC Method) (Note 1,2)
Operating Junction and Storage Temperature Range
TJ,TSTG
VALUE
5.0
40.0
UNITS
Watts
mW/¢J
See Fig. 5
Amps
-55 to +150
¢J
NOTES:
2
1. Mounted on 8.0mm copper pads to each terminal.
2. 8.3ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minute maximum.
1SMC5348 THRU 1SMC5388
ELECTRICAL CHARACTERISTICS (T A=25 ¢J unless otherwise noted, VF=1.2 Max @ IF=1A for all types.
Type No.
(Note 1.)
Nominal
Zener
Voltage
Vz @ IZT
Test
current
IZT
ZZT @ IZT
Z Zk @ IZK = 1
IR
mA
Ohms
mA
£g A
volts
(Note 2.)
11
12
13
14
15
16
17
18
19
20
22
24
25
27
28
30
33
36
39
43
47
51
56
60
62
68
75
82
87
91
100
110
120
130
140
150
160
170
180
190
200
Ohms
125
100
100
100
75
75
70
65
65
65
50
50
50
50
50
40
40
30
30
30
25
25
20
20
20
20
20
15
15
15
12
12
10
10
8
8
8
8
5
5
5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3.5
3.5
4
5
6
8
10
11
14
20
25
27
35
40
42
44
45
65
75
75
90
125
170
190
230
330
350
380
430
450
480
125
125
100
75
75
75
75
75
75
75
75
100
110
120
130
140
150
160
170
190
210
230
280
350
400
500
620
720
760
760
800
1000
1150
1250
1500
1500
1650
1750
1750
1850
1850
Maximum
Max
Max
Regulator
Surge
Voltage
Current
Current Regulation I mA
@ VR Volts
ZM
Ir Amps £GVz, Volts
(Note 5.)
Non & A
B-Suffix (Note 3.) (Note 4.)
Device
Marking
Code
Suffix
(Note 2.)
(Note 2.)
1SMC5348
1SMC5349
1SMC5350
1SMC5351
1SMC5352
1SMC5353
1SMC5354
1SMC5355
1SMC5356
1SMC5357
1SMC5358
1SMC5359
1SMC5360
1SMC5361
1SMC5362
1SMC5363
1SMC5364
1SMC5365
1SMC5366
1SMC5367
1SMC5368
1SMC5369
1SMC5370
1SMC5371
1SMC5372
1SMC5373
1SMC5374
1SMC5375
1SMC5376
1SMC5377
1SMC5378
1SMC5379
1SMC5380
1SMC5381
1SMC5382
1SMC5383
1SMC5384
1SMC5385
1SMC5386
1SMC5387
1SMC5388
Max reverse
Leakage Current
Maximum Zener
Impedance
5
2
1
1
1
1
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
8
8.6
9.4
10.1
10.8
11.5
12.2
13
13.7
14.4
15.8
17.3
18
19.4
20.1
21.6
23.8
25.9
28.1
31
33.8
36.7
40.3
43
44.6
49
54
59
63
65.5
72
79.2
86.4
93.6
101
108
115
122
130
137
144
8.4
9.1
9.9
10.6
11.5
12.2
12.9
13.7
14.4
15.2
16.7
18.2
19
20.6
21.2
22.8
25.1
27.4
29.7
32.7
35.8
38.8
42.6
45.5
47.1
51.7
56
62.2
66
69.2
76
83.6
91.2
98.8
106
114
122
129
137
144
152
8
7.5
7
6.7
6.3
6
5.8
5.5
5.3
5.1
4.7
4.4
4.3
4.1
3.9
3.7
3.5
3.3
3.1
2.8
2.7
2.5
2.3
2.2
2.1
2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.2
1.1
1.1
1
1
0.9
0.9
0.25
0.25
0.25
0.25
0.25
0.3
0.35
0.4
0.4
0.4
0.45
0.55
0.55
0.6
0.6
0.6
0.6
0.65
0.65
0.7
0.8
0.9
1
1.2
1.35
1.5
1.6
1.8
2
2.2
2.5
2.5
2.5
2.5
2.5
3
3
3
4
5
5
430
395
365
340
315
295
280
265
250
237
216
198
190
176
170
158
144
132
122
110
100
93
86
79
76
70
63
58
54.5
52.5
47.5
43
39.5
36.6
34
31.6
29.4
28
26.4
25
23.6
348B
349B
350B
351B
352B
353B
354B
355B
356B
357B
358B
359B
360B
361B
362B
363B
364B
365B
366B
367B
368B
369B
370B
371B
372B
373B
374B
375B
376B
377B
378B
379B
380B
381B
382B
383B
384B
385B
386B
387B
388B
NOTE:
1. TOLERANCE AND VOLTAGE DESIGNATION - The JEDEC type numbers shown indicate a tolerance of ¡Ó 10% with
guaranteed limits on only Vz, IR, Ir, and VF as shown in the electrical characteristics table. Units with guaranteed
limits on all seven parameters are indicated by suffix “B” for ¡Ó 5% tolerance.
2. ZENER VOLTAGE (Vz) AND IMPEDANCE (ZZT & ZZK) - Test conditions for Zener voltage and impedance are as
follows; Iz is applied 40 ¡Ó 10 ms prior to reading. Mounting contacts are located from the inside edge of mounting
¡Ï¢·
clips to the body of the diode.(TA=25 ¢J ¡Ð¢±¢J ).
3. SURGE CURRENT (Ir) - Surge current is specified as the maximum allowable peak, non-recurrent square-wave
current with a pulse width, PW, of 8.3 ms. The data given in Figure 5 may be used to find the maximum surge
current for a quare wave of any pulse width between 1 ms and 1000ms by plotting the applicable points on
logarithmic paper. Examples of this, using the 6.8v and 200V zeners, are shown in Figure 6. Mounting
¡Ï¢·
contact located as specified in Note 3. (TA=25 ¢J ¡Ð¢±¢J ).
4. VOLTAGE REGULATION (£GVz) - Test conditions for voltage regulation are as follows: Vz measurements are made
at 10% and then at 50% of the Iz max value listed in the electrical characteristics table. The test currents are the
same for the 5% and 10% tolerance devices. The test current time druation for each Vz measurement is 40 ¡Ó 10 ms.
¡Ï¢·
(TA=25 ¢J ¡Ð¢±¢J ). Mounting contact located as specified in Note2.
5. MAXIMUM REGULATOR CURRENT (IZM) - The maximum current shown is based on the maximum voltage of a
5% type unit. Therefore, it applies only to the B-suffix device. The actual IZM for any device may not exceed the
value of 5 watts divided by the actual Vz of the device. TL=75 ¢J at maximum from the device body.
APPLICATION NOTE:
Since the actual voltage available from a given zener
diode is temperature dependent, it is necessary to
determine junction temperature under any set of
operating conditions in order to calculate its value. The
following procedure is recommended:
Lead Temperature, TL, should be determined from:
TL = £c LAPD + TA
£c LA is the lead-to-ambient thermal resistance (¢J /W)
and PD is the power dissipation.
Junction Temperature, TJ , may be found from:
TJ = TL + £GTJL
£GTJL is the increase in junction temperature above the
of PD and the extremes of TJ(£GTJ) may be estimated.
Changes in voltage, Vz, can then be found from:
£GV = £c VZ £GTJ
£c VZ, the zener voltage temperature coefficient, is fount
from Figures 2.
Under high power-pulse operation, the zener voltage will
vary with time and may also be affected significantly be
the zener resistance. For best regulation, keep current
excursions as low as possible.
Data of Figure 3 should not be used to compute surge
capability. Surge limitations are given in Figure 5. They
lead temperature and may be found from Figure 3 for
are lower than would be expected by considering only
junction temperature, as current crowding effects cause
a train of power pulses or from Figure 4 for dc power.
£GTJL = £c JLPD
temperatures to be extremely high in small spots resulting
in device degradation should the limits of Figure. 5 be
For worst-case design, using expected limits of Iz, limits
exceeded.
RATING AND CHARACTERISTICS CURVES
1N5348B THRU 1N5388B
£c VZ, TEMPERATURE
COEFFICIENT (mA/¢J_@IZT
PD, MAXIUMU POWER DISSIPATION (WATTS)
TEMPERATURE COEFFICIENTS
8
L = LEAD LENGTH TO
HEAT SINK
(SEE FIGURE 5)
6
4
2
300
200
100
RANGE
50
30
20
10
5
0
20 40 60
80 100 120 140 160 180 200 220
0
0
20
40
60
80
100
120
140
VZ, ZENER VOLTAGE @IZT (VOLTS)
160
TL, LEAD TEMPERATURE (¢J)
Fig. 1-POWER TEMPERATURE DERATING CURVE
Fig. 2-TEMPERATURE COEFFICIENT-RANGE FOR UNITS
6 TO 220 VOLTS
£c JL(t,D), TRANSIENT THERMAL
RESISTANCE JUNCTION-TOLEAD(¢J/W)
30
20
10
7
5
D = 0.5
0.2
0.1
3
2
1
0.7
0.5
0.05
NOTE BELOW 0.1 SECOND,
THERMAL RESPONSE
CURVE IS APPLICABLE TO
ANY LEAD LENGTH (L)
0.02
0.01
0.3
0.0001 0.0002
D=0
0.0005
0.001
0.002
0.005
0.01
0.02
0.05
DUTY CYCLE, D = t1 / t2
SINGLE PULSE £GTJL = £KJL(t)PPK
REPETITIVE PULSES £GTJL = £KJL(t,D)PPK
0.1
0.2
0.5
1
2
5
10
TIME (SECONDS)
40
30
20
MCUNTE ON 8.0mm2
COPPER PADS TO
EACH TERMINAL
10
0
0
0.2
0.4
0.6
0.8
1
L, LEAD LENGTH TO HEAT SINK (INCH)
Fig. 4-TYPICAL THERMAL RESISTANCE
IR, PEAK SURGE CURRENT (AMPS)
JL, JUNCTION-TO -LEAD THERMAL
RESISTANCE (¢J /W)
Fig. 3-TYPICAL THERMAL RESPONSE
40
PW = 1ms*
20
PW = 8.3ms*
10
4
2
1
PW = 1000ms*
0.4
SINE / SQUARE WAVE PW = 100ms*
0.2
0.1
3
4
6
8 10
20
30 40
60 80 100
200
NOMINAL VZ(V)
Fig. 5-MAXIMUM NON-REPETITIVE SURGE
CURRENT VERSUS NOMINAL ZENER
VOLTAGE (SEE NOTE 3)
RATING AND CHARACTERISTICS CURVES
1N5348B THRU 1N5388B
ZENER VOLTAGE VERSUS ZENER CURRENT
(FIGURES 7,8, AND 9)
30
20
5
PLOTTED FROM INFORMATION
GIVEN IN FIGURE 6
2
TC = 25¢J
IZ, ZENER CURRENT (mA)
VZ = 6.8V
10
1
0.5
VZ = 200V
0.2
T = 25 ¢J
1000
100
10
1
0.1
0.1
1
10
100
1
1000
2
3
4
5
6
7
8
9
10
VZ, ZENER VOLTAGE (VOLTS)
Fig. 6-PEAK SURGE CURRENT VERSUS PULSE
WIDTH(SEE NOTE 3)
Fig. 7-ZENER VOLTAGE VERSUS ZENER CURRENT
VZ = 6.8 THRU 10 VOLTS
1000
T = 25 ¢J
IZ, ZENER CURRENT (mA)
IZ, ZENER CURRENT (mA)
1000
100
10
1
0.1
100
10
1
0.1
10
50
20
60
30
40
70
80
VZ, ZENER VOLTAGE (VOLTS)
Fig. 8-ZENER VOLTAGE VERSUS ZENER CURRENT
VZ = 11 THRU 75 VOLTS
80
100
120
140
160
180
200
220
VZ, ZENER VOLTAGE (VOLTS)
Fig. 9-ZENER VOLTAGE VERSUS ZENER CURRENT
VZ = 82 THRU 200 VOLTS
*** Data of Figure 3 should not be used to compute surge capability. Surge limitations are given in Figure 5. They are
lower than would be expected by considering only junction temperature, as current crowding effects cause
temperatures to be extremely high in small spots resulting in device degradation should the limits of Figure. 5 be
exceeded