February 2000 Programmable Downconverter Features Description • Up to 52 MSPS Front-End Processing Rates (CLKIN) and 35 MSPS Back-End Processing Rates (PROCCLK) Clocks May Be Asynchronous The HSP50214 Programmable Downconverter converts digitized IF data into filtered baseband data which can be processed by a standard DSP microprocessor. The Programmable Downconverter (PDC) performs down conversion, decimation, narrowband low pass filtering, gain scaling, re-sampling, and Cartesian to Polar coordinate conversion. • Processing Capable of >100dB SFDR8• Up to 255-Tap Programmable FIR • Overall Decimation Factor Ranging from 4 to 16384 • Output Samples Rates to ≅8.2 MSP8-S with Output Bandwidths to ≅625kHz Lowpass The 14-bit sampled IF input is down converted to baseband by digital mixers and a quadrature NCO, as shown in the Block Diagram. A decimating (4 to 32) fifth order Cascaded Integrator-Comb (CIC) filter can be applied to the data before it is processed by up to 5 decimate-by-2 halfband filters. The halfband filters are followed by a 255-tap programmable FIR filter. The output data from the programmable FIR filter is scaled by a digital AGC before being re-sampled in a polyphase FIR filter. The output section can provide seven types of data: Cartesian (I, Q), polar (R, θ), filtered frequency (dθ/dt), timing error (TE), and AGC level in either parallel or serial format. • 32-Bit Programmable NCO for Channel Selection and Carrier Tracking • Digital Re-Sampling Filter for Symbol Tracking Loops and Incommensurate Sample-to-Output Clock Ratios • Digital AGC with Programmable Limits and Sle8- Rate to Optimize Output Signal Resolution; Fixed or Auto Gain Adjust • Serial, Parallel, and FIFO 16-Bit Output Modes • Cartesian to Polar Converter and Frequency Discriminator for AFC Loops and Demodulation of AM, FM, FSK, and DPSK Ordering Information • Input Level Detector for External I.F. AGC Support PART NUMBER Applications TEMP. RANGE (oC) PACKAGE PKG. NO. • Single Channel Digital Software Radio Receivers HSP50214VC 0 to 70 120 Ld MQFP Q120.28x28 • Base Station Rx’s: AMPS, NA TDMA, GSM, and CDMA HSP50214VI -40 to 85 120 Ld MQFP Q120.28x28 • Compatible with HSP50210 Digital Costas Loop for PSK Reception • Evaluation Platform Available Block Diagram MICROPROCESSOR READ/WRITE C(7:0) CONTROL AGC LOOP FILTER AGC SOF CLKIN PROCCLK REFCLK 255-TAP FIR FILTER POLYPHASE FIR AND HALFBAND FILTERS SEROUTA CARTESIAN TO POLAR COORDINATE CONVERTER MAG. PHASE Q SYMBOL CARRIER NCO DISCRIMINATOR RE-SAMPLING NCO ∆ CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000 1 OUTPUT FORMATTER COF 5TH ORDER CIC FILTER I SYMBOL POLYPHASE FIR AND HALFBAND FILTERS 255-TAP FIR FILTER GAIN ADJ (2:0) HALFBAND FILTERS IN(13:0) 5TH ORDER CIC FILTER HALFBAND FILTERS LEVEL DETECT INPUT SECTION [ /Title (HSP5 0214) /Subject (Programmable Downconverter) /Autho r () /Keywords (Intersil Semiconductor, Downconverter, Down Converter, Programmable Downconverter, DSP, AMPS, TDMA , North American HSP50214 CT ODU ODUCT R P PR TE OLE TITUTE S B O UBS 4B LE S SP5021 B I S H POS SEROUTB AOUT(15:0) BOUT(15:0) FREQ TIMING ERROR File Number 4266.3 HSP50214 Pinout 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 IN11 IN12 IN13 AGCGNSEL VCC REFCLK GND OEAH AOUT15 AOUT14 AOUT13 AOUT12 AOUT11 AOUT10 GND NC AOUT9 AOUT8 AOUT7 AOUT6 AOUT5 VCC NC AOUT4 AOUT3 AOUT2 AOUT1 AOUT0 GND OEAL 120 LEAD MQFP TOP VIEW 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 31 32 33 34 35 36 37 38 39 40 51 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SYNCOUT INTRRP WR RD GND C7 C6 NC C5 C4 VCC C3 C2 C1 NC C0 A2 A1 A0 GND SEL2 SEL1 SEL0 GND SEROUTA SEROUTB SERSYNC SEROE SERCLK VCC IN10 IN9 IN8 GND IN7 NC IN6 IN5 IN4 IN3 IN2 GND IN1 IN0 VCC CLKIN GND NC ENI GAINADJ2 GAINADJ1 GAINADJ0 COF COFSYNC GND SOF SOFSYNC VCC SYNCIN1 SYNCIN2 2 DATARDY OEBH BOUT15 BOUT14 VCC NC BOUT13 BOUT12 BOUT11 BOUT10 BOUT9 BOUT8 GND GND PROCCLK VCC MSYNCI MSYNCO GND BOUT7 BOUT6 BOUT5 GND BOUT4 NC BOUT3 BOUT2 BOUT1 BOUT0 OEBL HSP50214 Pin Descriptions NAME TYPE DESCRIPTION VCC - Positive Power Supply Voltage. GND - Ground. CLKIN I Input Clock. This clock should be a multiple of the input sample rate. All input section processing occurs on the rising edge of CLKIN. IN(13:0) I Input Data. The format of the input data may be set to offset binary or 2’s complement. IN13 is the MSB (see control word 0). ENI I Input Enable. Active Low. This pin enables the input to the part in one of two modes, gated or interpolated (see control word 0). In gated mode, one sample is taken per CLKIN when ENI is asserted. GAINADJ(2:0) I GAINADJ Input. Adds an offset to the gain via the shifter following the mixer. GAINADJ value is added to the shift code from the microprocessor (µP) interface. The shift code is saturated to a maximum code of F. The gain is offset by (6dB)(GAINADJ). (000 = 0dB gain adjust; 111 = 42dB gain adjust) GAINADJ2 is the MSB. See “Using the Input Gain Adjust Control Signals” section. PROCCLK I Processing Clock. PROCCLK is the clock for all processing functions following the CIC section. Processing is performed on PROCCLK’s rising edge. All output timing is derived from this clock. NOTE: This clock may be asynchronous to CLKIN. AGCGNSEL I AGC Gain Select. This pin selects between two AGC loop gains. This input is setup and held relative to PROCCLK. Gain setting 1 is selected when AGCGNSEL = 1. COF I Carrier Offset Frequency Input. This serial input pin is used to load the carrier offset frequency into the Carrier NCO (see Serial Interface Section). The offset may be 8, 16, 24, or 32 bits. The setup and hold times are relative to CLKIN. This input is compatible with the output of the HSP50210 Costas loop [1]. COFSYNC I Carrier Offset Frequency Sync. This signal is asserted one CLK before the most significant bit (MSB) of the offset frequency word (see Serial Interface Section). The setup and hold times are relative to CLKIN. This input is compatible with the output of the HSP50210 Costas loop [1]. SOF I Resampler Offset Frequency Input. This serial input pin is used to load the offset frequency into the Resampler NCO (see Serial Interface Section). The offset may be 8, 16, 24, or 32 bits. The setup and hold times are relative to PROCCLK. This input is compatible with the output of the HSP50210 Costas loop [1]. SOFSYNC I Resampler Offset Frequency Sync. This signal is asserted one CLK before the MSB of the offset frequency word (see Serial Interface Section). The setup and hold times are relative to PROCCLK. This input is compatible with the output of the HSP50210 Costas loop [1]. AOUT(15:0) O Parallel Output Bus A. Two parallel output sources are available on the HSP50214. The first is called the Direct Output Port, where the source is selected through control word 20 (see the Microprocessor Write section) and comes directly from the Output MUX section (see Output Control Section). The most significant byte of AOUT always outputs the most significant byte of the Parallel Direct Output Port whose format is selected via µP interface. AOUT15 is the MSB. In this mode, the AOUT(15:0) bus is updated as soon as data is available. DATARDY is asserted to indicate new data. The second source for parallel data is called the Buffer RAM Output Port. The Buffer RAM Output Port acts like a FIFO for blocks of information called data sets. Within a data set is I, Q, magnitude, phase, and frequency information; a data type is selected using SEL(2:0). Up to 7 data sets are stored in the Buffer RAM Output Port. The LSBytes of the AOUT and BOUT busses form the 16 bits for the buffered output mode and can be used for buffered mode while the MSBytes are outputting data in the direct output mode. BOUT(15:0) O Parallel Output Bus B. Two parallel output sources are available on the HSP50214. The first is called the Direct Output Port, where the source is selected through control word 20 (see the Microprocessor Write section) and comes directly from the Output MUX section (see Output Control Section). The most significant byte of BOUT always outputs the most significant byte of the Parallel Direct Output Port whose format is selected via µP interface. BOUT15 is the MSB. In this mode, the BOUT(15:0) bus is updated as soon as data is available. DATARDY is asserted to indicate new data. The second source for parallel data is called the Buffer RAM Output Port. The Buffer RAM Output Port acts like a FIFO for blocks of information called data sets. Within a data set is I, Q, magnitude, phase, and frequency information; a particular information is selected using SEL(2:0). Up to 7 data sets is stored in the Buffer RAM Output Port. The least significant byte of BOUT can be used to either output the least significant byte of the B Parallel Direct Output Port or the least significant byte of the Buffer RAM Output Port. See Output Section. 3 HSP50214 Pin Descriptions (Continued) NAME TYPE DESCRIPTION DATARDY O Output Strobe Signal. Active low. Indicates when new data from the Direct Output Port section is available. DATARDY is asserted for one PROCCLK cycle during the first clock cycle that data is available on the parallel out busses. See Output Section. OEAH I Output enable for the MSByte of the AOUT bus. Active Low. OEAL I Output enable for the LSByte of the AOUT bus. Active Low. OEBH I Output enable for the MSByte of the BOUT bus. Active Low. OEBL I Output enable for the LSByte of the BOUT bus. Active Low. SEL(2:0) I Select Address is used to choose which information in a data set from the Buffer RAM Output Port is sent to the least significant bytes of AOUT and BOUT. SEL2 is the MSB. INTRRP O Interrupt Output. Active low. This output is asserted for 8 PROCCLK cycles when the Buffer RAM Output Port is ready for reading. SEROUTA O Serial Output Bus A Data. I, Q, magnitude, phase, frequency, timing error and AGC information can be sequenced in programmable order. See Output Section and Microprocessor Write Section. SEROUTB O Serial Output Bus B Data. Contents may be related to SEROUTA. I, Q, magnitude, phase, frequency, timing error and AGC information can be sequenced in programmable order. See Output Section and Microprocessor Write Section. SERCLK O Output Clock for Serial Data Out. Derived from PROCCLK as given by control word 20 in the Microprocessor Write Section. SERSYNC O Serial Output Sync Signal. Serves as serial data strobes. See Output Section and Microprocessor Write Section. SEROE I Serial Output Enable. When high, the SEROUTA, SEROUTB, SERCLK, and SERSYNC signals are set to a high impedance. C(7:0) I/O A(2:0) I Processor Interface Address Bus. See Microprocessor Write Section. A2 is the MSB. WR I Processor Interface Write Strobe. C(7:0) is written to control words selected by A(2:0) in the Programmable Down Converter on the rising edge of this signal. See Microprocessor Write Section. RD I Processor Interface Read Strobe. C(7:0) is read from output or status locations selected by A(2:0) in the Programmable Down Converter on the falling edge of this signal. See Microprocessor Read Section. REFCLK I Reference Clock. Used as an input clock for the timing error detector. The timing error is computed relative to REFCLK. REFCLK frequency must be less than or equal to PROCCLK/2. MSYNCO O Multiple Chip Sync Output. Provided for synchronizing multiple parts when CLKIN and PROCCLK are asynchronous. MSYNCO is the synchronization signal between the input section operating under CLKIN and the back end processing operating under PROCCLK. This output sync signal from one part is connected to the MSYNCI signal of all the HSP50214s. MSYNCI I Multiple Chip Sync Input. The MSYNCI pin of all the parts should be tied to the MSYNCO of one part. Processor Interface Data Bus. See Microprocessor Write Section. C7 is the MSB. NOTE: MSYNCI must be connected to an MSYNCO signal for operation. SYNCIN1 I CIC Decimation/Carrier NCO Update Sync. Can be used to synchronize the CIC section, carrier NCO update, or both. See the Multiple Chip Synchronization Section and Control Word 0 in the Microprocessor Write Section. Active High. SYNCIN2 I FIR/Timing NCO Update/AGC Gain Update Sync. Can be used to synchronize the FIR, Timing NCO update, AGC gain update, or any combination of the above. See the Multiple Chip Synchronization Section and Control Words 7, 8, and 10 in the Microprocessor Write Section. Active High. SYNCOUT O Strobe Output. This synchronization signal is generated by the µP interface for synchronizing multiple parts. Can be generated by PROCLK or CLKIN (see Control word 0 and Control word 24 in the Microprocessor Write Section). Active High. 4 AGCGNSEL TO OUTPUT FORMATTER AND MICROPROCESSOR INTERFACE PROCCLK AGCOUT LOOP FILTER LIMIT ERROR DETECT A CLKIN GAINADJ(2:0) (CO = 1; Cn = 0) INTRRP 1 TO 5 HALFBAND FILTER; DECIMATION UP TO 32 255-TAP PROGRAMMABLE FIR FILTER (DECIMATE UP TO 16) AGC SHIFT COS SIN 5 (CO = 1; Cn = 0) COF RESAMPLER AOUT(15:0) BOUT(15:0) Q atan ---- I DISCRIMINATOR 63-TAP PROGRAMMABLE FIR FILTER dθ dt (SYMBOL TRACKING) SOF I +Q 2 Q NCO (CARRIER TRACKING) 2 INTERPOLATE BY 2/4 HALFBANDS SEROUTB TIMING ERROR REFCLK DIFFERENCE A MICROPROCESSOR READ/WRITE RD WR A(2:0) C(7:0) CONTROL SECTION OUTPUT SECTION DISCRIMINATOR SECTION INPUT SECTION LEVEL DETECT SECTION SYNCHRONIZATION SECTION CARRIER NCO SECTIONS CIC, HALFBAND FILTER, AND FIR SECTIONS DIGITAL AGC SECTION RESAMPLER/INTERPOLATION HALFBAND SECTION TIMING NCO INTRRP SEL(2:0) SEROUTA NCO SOFSYNC OEAH OEAL OEBH OEBL CLKIN PROCCLK FIGURE 1. FUNCTIONAL BLOCK DIAGRAM OF THE HSP50214 PROGRAMMABLE DOWNCONVERTER AGCOUT CHIP SYNCHRONIZATION CIRCUITRY SERCLK SERSYNC SEROE MSYNCI SYNCOUT MSYNCO BACK END SYNCHRONIZATION CIRCUITRY SYNCIN2 FRONT END SYNCHRONIZATION CIRCUITRY SYNCIN1 HSP50214 TO µPROCESSOR INTERFACE COFSYNC DATARDY OUTPUT FORMATTER MIXER 5TH ORDER CIC DECIMATE FROM 4-32 I POLYPHASE FILTER LEVEL DETECT CARTESIAN TO POLAR POLYPHASE FILTER SHIFT IN(13:0) INPUT SECTION ENI HSP50214 Functional Description tion out of the Cartesian to Polar Coordinate converter are routed to the frequency detector, which is followed by a 63tap, 22-bit coefficient FIR filter structure for facilitating FM and FSK detection. The 14-bit input resolution is the smallest bit resolution found throughout the conversion and filtering sections, providing excellent dynamic range in the DSP processing. A unique input gain scaler adds an additional 42dB of range to the input level variation, to compensate for changes in the analog RF front end receive equipment. Synchronization circuitry allows precise timing control of the base station reconfiguration for all receive channels simultaneously. Portions of this table were corroborated with reference [2]. The HSP50214 Programmable Downconverter (PDC) is an agile digital tuner designed to meet the requirements of a wide variety of communications industry standards. The PDC contains the processing functions needed to convert sampled IF signals to baseband digital samples. These functions include LO generation/mixing, decimation filtering, programmable FIR shaping/bandlimiting filtering, re-sampling, automatic gain control (AGC), frequency discrimination and detection as well as multi-chip synchronization. The HSP50214 interfaces directly with a DSP microprocessor to pass baseband and status data. TABLE 1. CELLULAR PHONE BASE STATION APPLICATIONS USING FDMA A top level functional block diagram of the HSP50214 is shown in Figure 1. The diagram shows the major blocks and multiplexers used to reconfigure the data path for various architectures. The HSP50214 can be broken into 13 sections: Synchronization, Input, Input Level Detector, Carrier Mixer/Numerically Control Oscillator (NCO), CIC Decimating Filter, Halfband Decimating Filter, 255-Tap Programmable FIR Filter, Automatic Gain Control (AGC), Resampler/Halfband Filter, Timing NCO, Cartesian to Polar Converter, Discriminator, and Output sections. All of these sections are configured through a microprocessor interface. STANDARD AMPS (IS-91) RX BAND 824-849 (MHz) The HSP50214 has three clock inputs; two are required and one is optional. The input level detector, carrier NCO, and CIC decimating filter sections operate on the rising edge of the input clock, CLKIN. The halfband filter, programmable FIR filter, AGC, Resampler/Halfband filters, timing NCO, discriminator, and output sections operate on the rising edge of PROCCLK. The third clock, REFCLK, is used to generate timing error information. NOTE: All of the clocks may be asynchronous. PDC Applications Overview This section highlights the motivation behind the key programmable features from a communications system level perspective. These motivations will be defined in terms of ability to provide DSP processing capability for specific modulation formats and communication applications. The versatility of the Programmable Downconverter can be intimidating because of the many Control Words required for chip configuration. This section provides system level insight to help allay reservations about this versatile DSP product. It should help the designer capitalize on the greatest feature of the PDC - VERSATILITY THROUGH PROGRAMMABILITY. It is this feature, when fully understood, that brings the greatest return on design investment by offering a single receiver design that can process the many waveforms required in the communications marketplace. MCS-L1 NMT-400 MCS-L2 NMT-900 C450 ETACS NTACS 925-940 453-458 890-915 451-456 871-904 915-925 CHANNEL BW (kHz) 30 25.0 12.5 25 12.5 20.0 10.0 25.0 12.5 # TRAFFIC CHANNELS 832 600 1200 200 1999 222 444 1240 800 VOICE MODULATION FM FM FM FM FM PEAK DEVIATION (kHz) 12 5 5 4 9.5 CONTROL MODULATION FSK FSK FSK FSK FSK PEAK DEVIATION (kHz) 8 4.5 3.5 2.5 6.4 CONTROL CHANNEL RATE (Kbps) 10 0.3 1.2 5.3 8 TDM Based Standards and Applications Table 2 provides an overview of some common time division multiplying (TDM) base station applications to which the PDC can be applied. For time division multiple access (TDMA) applications, such as North American TDMA (IS136), where 30kHz is the received band of interest the PCS basestation, the PDC offers 0.012Hz frequency resolution in downconversion in addition to α = 0.35 matched (programmable) filtering capability. The π/4 DPSK modulation can be processed using the PDC Cartesian to Polar coordinate converter and dφ/dt detector circuitry or by processing the I/Q samples in the DSP µP. The PDC provides the ability to change the received signal gain and frequency, synchronous with burst timing. The synchronous gain adjustment allows the user to measure the power of the signal at the A/D at the end of a burst, and synchronously reload that same gain value at the arrival of the next user burst. FDM Based Standards and Applications Table 1 provides an overview of some common frequency division multiplex (FDM) base station applications to which the PDC can be applied. The PDC provides excellent selectivity for frequency division multiple access (FDMA) signals. This high selectivity is achieved with 0.012Hz resolution frequency control of the NCO and the sharp filter responses capable with a 255-tap, 22-bit coefficient FIR filter. The 16-bit resolu- For applications other than cellular phones (where the preambles are not changed), the PDC frequency discriminator output can be used to obtain correlation on the preamble pattern to aid in burst acquisition. 6 HSP50214 versions of these formats, ASK and FSK are also readily processed using the PDC. Just as in the AM modulated case, ASK signals will use 15-bit magnitude output of the Cartesian to Polar Coordinate converter. Multi-tone FSK can be processed several ways. The frequency information out of the discriminator can be used to identify the received tone, or the filter can be used to identify and power detect a specific tone of the received signal. AMPS is an example of a FM application. TABLE 2. CELLULAR BASESTATION APPLICATIONS USING TDMA STANDARD GSM PCN IS-54 TYPE Cellular Cellular Cellular BASESTATION RX BAND (MHz) 935-960 1805-1880 824-849 200 200 30 8 16 3 GMSK GMSK π/4 CHANNEL BW (kHz) # TRAFFIC CHANNELS VOICE MODULATION PM and PSK The PDC provides the downconversion, demodulation, matched filtering and coordinate conversion required for demodulation of PM and PSK modulated waveforms. These modulation formats will require external carrier and symbol timing recovery loop filters to complete the receiver design. The PDC was designed to interface with the HSP50210 Digital Costas Loop to implement the carrier phase and symbol timing recovery loop filters. DPSK CHANNEL RATE (Kbps) 270.8 270.8 48.6 CONTROL MODULATION GMSK GMSK π/4 DPSK CHANNEL RATE (Kbps) 270.8 270.8 48.6 Several applications are combinations of frequency and time domain multiple access schemes. For example, GSM is a TDMA signal that is frequency hopped. The individual channels contain Gaussian MSK modulated signals. The PDC again offers the 0.012Hz tuning resolution for de-hopping the received signal. The combination of halfband and 256-tap programmable, 22-bit coefficient FIR filters readily performs the necessary matched filtering for demodulation and optimum detection of the GMSK signals. Digital modulation formats that combine amplitude and phase for symbol mapping, such as m-ary QAM can also be downconverted, demodulated, and matched filtered. The received symbol information is provided with 16 bits of resolution in either Cartesian or Polar coordinates to facilitate remapping into bits and to recover the carrier phase. External Symbol mapping and Carrier Recovery Loop Filtering is required for this waveform. Re-Sampling and Interpolation Filters CDMA Based Standards and Applications Two key features of the re-sampling FIR filter are that the resampler filter allows the output sample rate to be programmed with millihertz resolution and that the output sample rate can be phase locked to an independent separate clock. The resampler frees the front end sampling clocks from having to be synchronous or integrally related in rate to the baseband output. The asynchronous relationship between front end and back end clocks is critical in applications where ISDN interfaces drive the baseband interfaces, but the channel sample rates are not related in any way. The interpolation halfband filters can increase the rate of the output when narrow frequency bands are being processed. The increase in output rate allows maximum use of the programmable FIR while preserving time resolution in the baseband data. For Code Division Multiple Access (CDMA) type signals, the PDC offers the ability to have a single wideband RF front end, from which it can select a single spread channel of interest. The synchronization circuitry provides for easy control of multiple PDC for applications where multiple received signals are required, such as base-stations. In IS-95 CDMA, the receive signal bandwidth is 1.2288MHz wide with many spread spectrum channel in the band. Each spread channel is a QPSK signal. The PDC supplies the downconversion and filtering required to receive a single spread channel in the presence of strong adjacent interference. Multiple PDC’s would be sourced from a single receive RF chain, each processing a different receive frequency channel. The despreader would usually follow the PDC. In some very specific applications, with short, fixed codes, the filtering and despreading may be possible with innovative use of the programmable, 22-bit coefficient FIR filter. The PDC offers 0.012Hz resolution on tuning to the desired receive channel and excellent rejection of the portions of the band not being processed, via the halfband and 255-tap programmable, 22-bit coefficient FIR filter. 14-Bit Input and Processing Resolution The PDC maintains a minimum of 14 bits of processing resolution through to the output. Which provides over 84dB of dynamic range. The 18 bits of resolution on the internal references provide a spurious floor that is better than 98dBc. Furthermore, the PDC provides up to 42dB of gain scaling to compensate for any change in gain in the RF front end as well as up to 96dB of gain in the internal PDC AGC. This gain maximizes the output resolution for small signals and compensates for changes in the RF front end gain, to handle changes in the incoming signal. Traditional Modulation Formats AM, ASK, FM and FSK The PDC has the capability to fully demodulate AM and FM modulated waveforms. The PDC outputs 15 bits of amplitude or 16 bits of frequency for these modulation formats. The FM discriminator has a 63-tap programmable, 22-bit coefficient FIR filter for additional signal conditioning of the FM signal. Digital 7 HSP50214 reset on SYNCIN2 using Control Word 7, bit 21. The MSYNCO of one of the PDCs is then used to drive the MSI of all the PDCs (including its own). Summary The greatest feature of the PDC is its ability to be reconfigured to process many common standards in the communications industry. Thus, a single hardware element can receive and process a wide variety of signals from PCS to traditional cellular, from wireless local loop to SATCOM. The high resolution frequency tuning and narrowband filtering are instrumental in almost all of the applications. For application configurations where CLKIN and PROCCLK have the same source, SYNCIN1 and SYNCIN2 can be tied together. However, if different enabling is desired for the front end and backend processing of the PDC’s, these signals can still be controlled independently. In summary, SYNCIN1 is used to update phase offset, update center frequency, reset CIC decimation counters and reset the carrier NCO (clear the feedback in the NCO). SYNCIN2 is used to reset the HB filter, FIR filter, resampler/HB state machines and the output FIFO, load a new gain into the AGC and load a new resampler NCO center frequency and phase offset. Multiple Chip Synchronization Multiple PDCs are synchronized using a MASTER/SLAVE configuration. One part is responsible for synchronizing the front end internal circuitry using CLKIN while another part is responsible for synchronizing the backend internal circuitry using PROCCLK. The PDC is synchronized with other PDCs using five control lines: SYNCOUT, SYNCIN1, SYNCIN2, MSYNCO, and MSYNCI. Figure 2 shows the interconnection of these five signals for multiple chip synchronization where different sources are used for CLKIN and PPOCCLK. Input Section The block diagram of the input controller is provided in Figure 3. The input can support offset binary or two’s complement data and can be operated in gated or interpolated mode (see Control Word 0 from the Microprocessor Write Section). The gated mode takes one sample per clock when the input enable (ENI) is asserted. The gated mode allows the user to synchronize a low speed sampling clock to a high speed CLKIN. PDC A is the Master sync through MSO. PDC B configures the CLKIN sync through SYNCIN1. PDC A configures the PROCCLK sync through SYNCIN2. A B HSP50214 The interpolated mode allows the user to input data at a low sample rate and to zero-stuff the data prior to filtering. This zero stuffing effectively interpolates the input signal up to the rate of the input clock (CLKIN). This interpolated mode allows the part to be used at rates where the sampling frequency is above the maximum input rate range of the halfband filter section, and where the desired output bandwidth is too wide to use a cascaded integrator comb (CIC) filter without significantly reducing the dynamic range. See Figures 4-7 for an interpolated input example, detailing the associated spectral results. HSP50214 (MASTER)MSO MSI (MASTER SYNCIN2) SYNCOUT MSO MSI SYNCOUT SYNCIN2 SYNCIN2 SYNCIN1 SYNCIN1 (MASTER SYNCIN1) ALL OTHER SYNCIN1 ALL OTHER SYNCIN2 Interpolation Example: ALL OTHER MSI The specifications for the interpolated input example are: FIGURE 2. SYNCHRONIZATION CIRCUIT Input Sample Rate = 5 MSPS PROCCLK = 28MHz Interpolate by 8, Decimate by 10 Desired 85dB dynamic range output bandwidth = 500kHz SYNCOUT for PDC B should be set to be synchronous with CLKIN (Control Word 0, bit 3 = 0. See the Microprocessor Write Section). SYNCOUT for PDC B is tied to the SYNCIN1 of all the PDCs. The SYNCIN1 can be programmed so that the carrier NCO and/or the 5th order CIC filter of all PDCs can be synchronously loaded/updated using SYNCIN1. See Control Word 0, bits 19 and 20 in the Microprocessor Write Section for details. Input Level Detector The Input Level Detector Section measures the average magnitude error at the PDC input for the microprocessor by comparing the input level against a programmable threshold and then integrating the result. It is intended to provide a gain error for use in an AGC loop with either the RF/IF or A/D converter stages (see Figure 8). The AGC loop includes Input Level Detector, the microprocessor and an external gain control amplifier (or attenuator). The input samples are rectified and added to a threshold programmed via the microprocessor interface, as shown in Figure 9. The bit weighting of the data path through the SYNCOUT for one of the other PDC’s besides PDC B, should be set for PROCCLK (bit 3 = 1 in Control Word 0). This output signal is tied to the SYNCIN2 of all PDCs. The SYNCIN2 can be programmed so that the AGC updates its accumulator with the contents in the master registers (Control Word 8, bit 29 in the Microprocessor Write Section). SYNCIN2 is also used to load or reset the timing NCO using bit 5, Control Word 11. The halfband and FIR filters can be 8 HSP50214 cessor interface through Control Word 1. Only the upper 16 bits are programmable. The 2 LSBs are always zero. Control Word 1, bits 29-14 are programmed to: input threshold detector is shown in Figure 10. The threshold is a signed number, so it should be set to the inverse of the desired input level. The threshold can be set to zero if the average input level is desired instead of the error. The sum of the threshold and the absolute value of the input is accumulated in a 32-bit accumulator. The accumulator can handle up to 218 samples without overflow. The integration time is controlled by an 18-bit counter. The integration counter preload (ICPrel) is programmed via the micropro- ICPrel = ( N ) ⁄ 4 + 1 (EQ. 1) where N is the desired integration period, defined as the number of input samples to be integrated. N must be a multiple of 4: [0, 4, 8, 12, 16 .... , 218]. INPUT LEVEL DETECTOR † STATUS (0) † INPUT_THRESH INTG_MODE † SHIFT REG NCO †† LIMIT EN 3 GAINADJ(2:0) DELAY 3 † ∑ 4 ENI INTERP DELAY 3 † CONTROL WORD 0 CONTROL WORD 1 BYPASS 4 CIC INPUT FORMAT † REG REG REG INPUT FORMAT INTG_INTEVAL IN(13:0) † † MUX LEVEL DETECT CONTROL LOGIC CLKIN INTERP † OFFSET_BIN † INPUT_THRESH † INTG_MODE † INTG_INTEVAL † † Controlled via microprocessor interface. †† See NCO section for more details. FIGURE 3. BLOCK DIAGRAM OF THE INPUT SECTION ↑8 (0 STUFF) = 40MHz BYPASS PROCCLK = 28MHz MUX 5MHz CIC FILTER MIN. R = 4 4MHz HB/FIR FILTER MAX. fS = 4MHz (EXCEEDED IN BYPASS PATH) 5MHz 500kHz = 85dB BANDWIDTH (NOT ACHIEVED WITH CIC FILTER PATH) CIC FILTER R = ↓10 HB/FIR FILTER 500kHz = 85dB BANDWIDTH Without Interpolation, the CIC bypass path exceeds the HB/FIR filter input sample rate and the CIC filter path will not yield the desired 85dB dynamic range band width of 500kHz. FIGURE 5. BLOCK DIAGRAM OF THE INTERPOLATION APPROACH FIGURE 4. STATEMENT OF THE PROBLEM 9 HSP50214 fS 5MHz 2fS 10MHz 3fS 4fS 5fS 6fS 7fS 8fS 15MHz 20MHz 25MHz 30MHz 35MHz 40MHz THE INPUT DATA SPECTRUM SAMPLED AT RATE R = fS f’S /8 5MHz f’s/4 10MHz 3f’S /8 15MHz f’S /2 20MHz 5f’S /8 25MHz 3f’S /4 30MHz 7f’S /8 35MHz 9fS 45MHz 10fS 50MHz f’S 40MHz FIGURE 6. INTERPOLATION SPECTRUM: INTERPOLATE BY 8 THE INPUT DATA WITH ZERO STUFFING; SAMPLE AT RATE R = f’S 4MHz 8MHz 12MHz 16MHz 20MHz 24MHz 28MHz 32MHz 36MHz 40MHz DECIMATE BY 10 AND CIC FILTER; SAMPLE AT RATE R = f’S/10 85dB DYNAMIC RANGE BANDWIDTH CIC FILTER FREQUENCY RESPONSE CIC FILTER ALIAS PROFILE O.5MHz 1MHz 2MHz 3MHz 4MHz FIGURE 7. ALIAS PROFILE AND THE 85dB DYNAMIC RANGE BANDWIDTH µPROC INPUT LEVEL DETECTOR (24-BIT ERROR VALUE) DAC THRESH IF INPUT A/D PDC GCA FIGURE 8. PROCESSOR BASED EXTERNAL IF AGC ACCUMULATOR ADDR(2:0) 32 IN(13:0) INPUT GATING LOGIC + |X| + CLKIN INPUT_THRESHOLD † R E G INTEGRATION_INTERVAL† 16 START † INTEGRATION_MODE † “0” COUNTER CLKIN † Controlled via microprocessor interface. CONTINUOUS SINGLE FIGURE 9. 10 R E G R E G 24 M U X 8 TO µPROC HSP50214 Typically, the average input error is read from the Input Level Detector port for use in AGC applications. By setting the threshold to 0, however, the average value of the input signal can be read directly. The calculation is: The integration period counter can be set up to run continuously or to count down and stop. Continuous integration counter operation lets the counter run, with sampling occurring every time the counter reaches zero. Because the processor samples the detector read port asynchronous to the CLKIN, data can be missed unless the status bit is monitored by the processor to ensure that a sample is taken for every integration count down sequence. dBFS RMS = ( 20 ) log [ ( 1.111 ) ( leve l ) ⁄ ( ( N ) ( 16 ) ) ] where “level” is the 24-bit value read from the 3 level detector registers and “N” is the number of samples to be integrated. Note that to get the average value of a sinusoid, multiply the RMS value by 1.111. For a full scale input sinusoid, this yields an RMS value of approximately 3dBFS. A) INPUT SIGNAL AMPLITUDE AMPLITUDE AMPLITUDE AMPLITUDE D) ACCUMULATOR INPUTS F) CLOSED LOOP STEADY STATE (CONSTANT INPUT) AMPLITUDE AMPLITUDE E) DETECTOR OUTPUT 010 0 218 217 216 215 214 213 212 211 210 29 28 27 26 25 24 23 22 21 20 2-1 2-2 2-3 2-4 B) RECTIFIED SIGNAL C) THRESHOLD FIGURE 11. SIGNAL PROCESSING WITHIN LEVEL DETECTOR Carrier Synthesizer/Mixer The carrier synthesizer/mixer section of the HSP50214 is shown in Figure 12. The NCO has a 32-bit phase accumulator, a 10-bit phase offset adder, and a sine/cosine ROM. The frequency of the NCO is the sum of a center frequency control word, loaded via the microprocessor interface (Control Word 3, bits 0 to 31), and an offset frequency, loaded serially via the COF and COFSYNC pins. The offset frequency can be zeroed in Control Word 0, bit 1. Both frequency control terms are 32 bits and the addition is modulo 232. The output frequency of the NCO is computed as: 001 -20 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 . µPROC READ PORTS READ CODE A(2:0) MAGNITUDE 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 NOTE: 1.111 scales the sinusoid average (2/π) to 1/√2 000 20 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 ACCUMULATOR 20 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 THESHOLD f S -6dB -12dB -18dB -24dB -30dB -36dB -42dB -48dB -54dB -60dB -66dB -72dB -78dB -84dB -90dB INPUT A/D OUTPUT In the count down and stop mode, the microprocessor read commands can be synchronized to system events, such as the start of a burst for a TDMA application. The integration counter can be started at any time by writing to Control Word 2. At the end of the integration period (counter = 0000), the upper 23 bits of the accumulator are transferred to a holding register for reading by the microprocessor. Note that it is not the restarting of the counter (by writing to Control Word 2) that latches the current value, but the end of the integration count. When the accumulator results are latched, a bit is set in the status register to notify the processor. Reading the most significant byte of the 23 bits clears the status bit. See the Microprocessor Read Section. Figure 11 illustrates a typical AGC detection process. 218 217 216 215 214 213 212 211 210 29 28 27 26 25 24 23 22 21 20 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 (EQ. 2) F C = f IN * N ⁄ ( 2 32 ), (EQ. 3) or in terms of the programmed value: N = INT [ F C × 2 32 ⁄ F IN ] HEX , (EQ. 3A) where N is the 32-bit sum of the center and offset frequency terms, fIN is the input sampling frequency, and INT is the integer of the computation. See the Microprocessor Write Section on instructions for writing Control Word 3. FIGURE 10. INPUT THRESHOLD DETECTOR BIT WEIGHTING 11 HSP50214 For example, if N is 3267 (decimal), and fIN is 52MHz, then FC is 39.55Hz. If received data is modulated at a carrier frequency of 10MHz, then the synthesizer/mixer should be programmed for N = 313B13B1 (hex) or CEC4EC4F(hex). would produce a phase offset of 11.25o and a value of -512 would produce an offset of 180o. The phase offset is loaded via the microprocessor interface. See the Microprocessor Write Section on instructions for writing Control Word 4. Because the input enable, ENI, controls the operation of the phase accumulator, the NCO output frequency is computed relative to the input sample rate, fIN, not to fCLKIN. The frequency control, N, is interpreted as two’s complement because the output of the NCO is quadrature. Negative frequency L.O.s select the upper sideband; positive frequency L.O.s select the lower sideband. The range of the NCO is fIN/2 to +fIN/2. The frequency resolution of the NCO is fIN/(232) or approximately 0.012Hz when CLKIN is 52 MSPS and ENI is tied low. The most significant 18 bits from the phase adder are used as the address a sin/cos look-up table. This look-up table maps phase into sinusoidal amplitude. The sine and cosine values have 18 bits of amplitude resolution. The spurious components in the sine/cosine generation are at least -96dBc. The sine and cosine samples are routed to the mixer section whSere they are multiplied with the input samples to translate the signal of interest to baseband. The mixer multiplies the 14-bit input by the 18-bit quadrature sinusoids. The mixer equations are: TO MIXERS COS SIN 18 18 REG REG CARRIER PHASE STROBE † + 10 R E G R E G PHASE ACCUMULATOR REG ENI CLEAR PHASE ACCUM † R E G MUX + COF ENABLE † MUX 32 32 COF 0 CF REG COFSYNC SYNC CARRIER LOAD ON UPDATE† REG COF SHIFT REG SYNCIN1 SYNC CIRCUITRY (EQ. 5A) The second technique, designed for synchronizing updates to multiple parts, uses the SYNCIN1 pin to update the active registers. When Control Word 1, bit 20 is set to 1, the SYNCIN1 pin causes both the center frequency and phase offset holding registers to be transferred to active registers. Additionally, when Control Word 0, bit 0 is set to 1, the feedback in the phase accumulator is zeroed when the transfer from the holding to active register occurs. This feature provides synchronization of the phase accumulator starting phase of multiple parts. It can also be used to reset the phase of the NCO synchronous with a specific event. CARRIER FREQUENCY STROBE † REG Q OUT = I IN × sin ( ω c ) To allow the frequency and phase of multiple parts to be updated synchronously, two sets of registers are used for latching the center frequency and phase offset words. The offset phase and center frequency control words are first loaded into holding registers. The contents of the holding registers are transferred to active registers in one of two ways. The first technique involves writing to a specific Control Word Address. A processor write to Control Word 5, transfers the center frequency value to the active register while a processor write to Control Word 6 transfers the phase offset value to the active register. CARRIER PHASE OFFSET † 0 (EQ. 5) The mixer output is rounded symmetrically to 15 bits. SIN/COS ROM 18 I OUT = I IN × cos ( ω c ) CARRIER FREQUENCY† † Controlled via microprocessor interface. FIGURE 12. BLOCK DIAGRAM OF NCO SECTION The carrier offset frequency is loaded using the COF and COFSYNC pins. Figure 13 details the timing relationship between COF, COFSYNC and CLKIN. The offset frequency word can be zeroed if it is not needed. Similarly, the Sample Offset Frequency register controlling the resampler NCO is loaded via the SOF and SOFSYNC pins. The procedure for loading data through the two pin NCO interfaces is identical except that the timing of SOF and SOFSYNC is relative to PROCCLK. The phase of the Carrier NCO can be shifted by adding a 10-bit phase offset to the MSB’s (modulo 360o) of the output of the phase accumulator. This phase offset control has a resolution of 0.35o and can be interpreted as two’s complement from -180o to 180o (-π to π) or as binary from 0 to 360o (0 to 2π). The phase offset is given by: φ OFF = 2π × ( PO ⁄ 2 10 9 9 ) ;( – ( 2 – 1 ) < PO < ( 2 – 1 ) ) (EQ. 4) or, in terms of the parameter to be programmed: PO = INT [ ( 2 10 φ OFF ) ⁄ 2π ] HEX ;( – π < φ OFF < π ) (EQ. 4A) where PO is the 10-bit two’s complement value loaded into the Phase Offset register (Control Word 4, bits 9-0). For example, a value of 32 (decimal) loaded into the Phase Offset register 12 HSP50214 CIC Decimation Filter CLKIN The mixer output may be filtered with the CIC filter or it may be routed directly to the halfband filters. The CIC filter is used to reduce the sample rate of a wideband signal to a rate that the halfbands and programmable filters can process, given the maximum computation speed of PROCCLK. (See Halfband and FIR Filter Sections for techniques to calculate this value.) COFSYNC/ SOFSYNC COF/ SOF OTE: MSB LSB MSB Data must be loaded MSB first. Prior to the CIC filter, the output of the mixer goes through a barrel shifter. The shifter is used to adjust the gain in 6dB steps to compensate for the variation in filter gain with decimation. (See Equation 6). Fine gain adjustments must be done in the AGC section. The shifter is controlled by the sum of a 4-bit CIC Shift Gain word from the microprocessor and a 3-bit gain word from the GAINADJ(2:0) pins. The three bit value is pipelined to match the delay of the input samples. The sum of the 3 and 4-bit shift gain words saturates at a value of 15. Table 3 details the permissible values for the GAINADJ(2:0) barrel shifter control, while the Figure 15 shows the permissible CIC Shift Gain values. IGURE 13. SERIAL INPUT TIMING FOR COF AND SOF INPUTS Each serial word has a programmable word width of either 8, 16, 24, or 32 bits (See Control Word 0, bits 4 and 5, for the Carrier NCO programming and Control Word 11, bits 3 and 4, for Timing NCO programming). On the rising edge of the clock, data on COF or SOF is clocked into an input shift register. The beginning of a serial word is designated by asserting either COFSYNC or SOFSYNC “high” one CLK period prior to the first data bit. 32 † 30 28 26 24 † 22 20 18 16 † 14 12 10 8† 6 4 2 0 The CIC filter structure for the HSP50214 is fifth order; that is it has five integrator/comb pairs. A fifth order CIC has 84dB of alias attenuation for output frequencies below 1/8 the CIC output sample rate. CIC SHIFT GAIN (FROM PROCESSOR) SHIFT COUNTER VALUE The assertion of the COFSYNC (or SOFSYNC) starts a count down from the programmed word width. On following CLKs, data is shifted into the register until the specified number of bits have been input. At this point the contents of the register are transferred from the shift register to the respective 32-bit holding register. The shift register can accept new data on the following CLK. If the serial input word is defined to be less than 32 bits, it will be transferred to the MSBs of the 32-bit holding register and the LSBs of the holding register will be zeroed. See Figure 14 for details. ASSERTION OF COFSYNC, SOFSYNC DATA TRANSFERRED TO HOLDING REGISTER (8) (24) (32) (16) 2 6 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 8-BIT INPUT 10-BIT INPUT 12-BIT INPUT 14-BIT INPUT ALLOWABLE CIC SHIFT GAINS ARE BELOW THE CURVES 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 DECIMATION (R) FIGURE 15. CIC SHIFT GAIN VALUES 10 14 18 22 26 30 34 38 42 46 50 54 CLK TIMES TD †† The decimation rate of the CIC filter is programmed in Control Word 0, bits 12 - 7. The CIC Shift Gain is programmed in Control Word 0, bits 16-13. The CIC Bypass is set in Control Word 0, bit 6. TD †† TD †† TD †† † Serial word width can be: 8, 16, 24, 32 bits wide. † TD is determined by the COFSYNC, COFSYNC rate. TABLE 3. GAIN ADJUST CONTROL AND CIC DECIMATION ∆GAIN VALUE (dB) GAIN ADJ(2:0) MAX. CIC DECIMATION 0 000 32 6 001 27 12 010 24 18 011 21 24 100 18 NOTE: COF loading and timing is relative to CLKIN while SOF loading and timing is relative to PROCCLK. 30 101 16 36 110 12 NOTE: TD can be 0, and the fastest rate is with 8-bit word width. 42 111 10 FIGURE 14. HOLDING REGISTERS LOAD SEQUENCE FOR COF AND SOF SERIAL OFFSET FREQUENCY DATA NOTE: Serial Data must be loaded MSB first, and COFSYNC or SOFSYNC should not be asserted for more than one CLK cycle. 13 HSP50214 would not drop by 12dB. This fixed gain adjust eliminates the need for the software to continually normalize. CIC Gain Calculations The gain through the CIC filter increases with increased decimation. The programmable barrel shifter that precedes the first integrator in the CIC is used to offset this variation. Gain variations due to decimation should be offset using the 4-bit CIC Shift Gain word. This allows the input signal level to be adjusted in 6dB steps to control the CIC output level. One must, exercise care when using this function as it can cause overflow in the CIC filter. Each gain adjust in the shifter from the gain adjust control signals is the equivalent of an extra bit of input. The maximum decimation in the CIC is reduced accordingly. With a decimation of 32, all 40 bits of the CIC are needed, so no input offset gain is allowed. As the decimation is reduced, the allowable offset gain increases. Table 3 shows the decimation range versus desired offset gain range. Table 3 assumes that the CIC Shift Gain has been programmed per Equation 7 or 8A. The gain at each stage of the CIC is: (EQ. 6) where R is the decimation factor and N is the number of stages. The input to the CIC from the mixer is 15 bits, and the bit widths of the accumulators for the five stages in the HSP50214 are 40, 36, 32, 32, and 32, as shown in Figure 16. This limits the maximum decimation in the CIC to 32 for a full scale input. 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 For 14 bits, Equation 7 becomes: 5 SG = FLOOR [ 25 – log 2 ( R ) ]for 4 < R < 32 = 15 (EQ. 8A) fo r R = 4 For 12 bits, Equation 7 becomes: 5 (EQ. 8B) OUTPUT SHIFTER BITS TAKEN WHEN CIC IS BYPASSED SG = FLOOR [ 27 – log 2 ( R ) ]for 5 < R < 40 = 15 for 4 ≤ R ≤ 5 For 10 bits, Equation 7 becomes: 5 SG = FLOOR [ 29 – log 2 ( R ) ]for 6 < R < 52 for 4 ≤ R ≤ 6 = 15 (EQ. 8C) For 8 bits, Equation 7 becomes: 5 SG = FLOOR [ 31 – log 2 ( R ) ]for 9 < R < 64 = 15 (EQ. 8D) for 4 ≤ R ≤ 9 Figure 15 is plot of Equations 8A through 8D. The 4-bit CIC Shift Gain word has a range from 0 to 15. The 6-bit Decimation Rate Register, (R-1), has a range from 0 to 63, limited by the input resolution as cited above. Using the Input Gain Adjust Control Signals The input gain offset control GAINADJ(2:0)) is provided to offset the signal gain through the part, i.e. to keep the CIC filter output level constant as the analog front end attenuation is changed. The gain adjust offset is 6dB per code, so the gain adjust range is 0 to 42dB. For example, if 12dB of attenuation is switched in at the receiver RF front end, a code of 2 would increase the gain at the input to the CIC filter up 12dB so that the CIC filter output 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 2-25 2-26 2-27 2-28 2-29 2-30 2-31 2-32 2-33 2-34 2-35 2-36 2-37 2-38 2-39 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 2-25 2-26 2-27 2-28 2-29 2-30 2-31 2-32 2-33 2-34 2-35 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 2-25 2-26 2-27 2-28 2-29 2-30 2-31 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 2-25 2-26 2-27 2-28 2-29 2-30 2-31 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 2-25 2-26 2-27 2-28 2-29 2-30 2-31 CIC OUTPUT ACC5 NOTE: The number of input bits is IIN. (If the number of bits into the CIC filter used the value 40 replaces 39). ACC4 (EQ. 7) ACC3 Thus the value of the CIC Shift Gain word can be calculated: ACC2 INPUT (SHFT=0) If R is 32, the gain through all five integrator stages is 325 = 225. (The gain through the last four CIC stages it is 220, through the last 3 it is 215, etc.) The sum of the input bits and the growth bits cannot exceed the accumulator size. This means that for a decimation of 32 and 15 input bits, the first accumulator must be 15 + 25 = 40 bits. ACC1 The CIC filter decimation counter can be loaded synchronous with other PDC chips, using the SYNCIN1 signal and the CIC External Sync Enable bit. The CIC external Sync Enable is set via Control Word 0, bit 19. INPUT (SHFT=15) N k = R , 0 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 FIGURE 16. CIC FILTER BIT WEIGHTING NOTE: If 14 input bits are not needed, the gain adjust can be increased by one for each bit that the input is shifted down at the input. For example, if only 12 bits are needed, an offset range of 24dB is possible for a decimation of 24. 14 HSP50214 Halfband Decimating Filters HALFBAND FILTER INPUT The Programmable Down Converter has five halfband filter stages, as shown in Figure 17. Each stage decimates by 2 and filters out half of the available bandwidth. The first halfband, or HB1, has 7 taps. The remaining halfbands; HB2, HB3, HB4, and HB5; have 11, 15, 19, and 23 taps respectively. The coefficients for these halfbands are given in Table 4. Figure 18 shows the frequency response of each of the halfband filters with respect to normalized frequency, FN. Frequency normalization is with respect to the input sampling frequency of each filter section. Each stage is activated by their respective bit location (15-20) in Control Word 7. Any combination of halfband filters may be used, or all may be bypassed. Figure 19 details the halfband alias profiles with respect to normalized frequency FN . fIN = fS FN = fIN HALFBAND FILTER 1 0 CONTROL WORD 7, BIT 15 FHB1 = fS OR fS/2 HALFBAND FILTER 2 0 CONTROL WORD 7, BIT 16 FN = FHB2 1 HALFBAND FILTER 3 (EQ. 9) † FHB2 = FHB1 OR FHB1/2 0 CONTROL WORD 7, BIT 17 N 1 FN = FHB1 Since each halfband filter section decimates by 2, the total decimation through the halfband filter is given by: DEC HB = 2 † † 1 FHB3 = FHB2 OR FHB2/2 FN = FHB3 HALFBAND FILTER 4 where N = Number of Halfband Filters Selected (1 - 5). 0 CONTROL WORD 7, BIT 18 † 1 FHB4 = FHB3 OR FHB3/2 FN = FHB4 HALFBAND FILTER 5 CONTROL WORD 7, BIT 19 0 † 1 F5 = FHB4 OR FHB4/2 HALFBAND FILTER OUTPUT † Each halfband section decimates by 2 FIGURE 17. BLOCK DIAGRAM OF HALFBAND FILTER SECTION 0 0 ALIAS PROFILES -6dB BANDWIDTH MAGNITUDE (dB) MAGNITUDE (dB) -40 -60 -80 -6dB BANDWIDTH -20 -20 HALFBAND FILTER 5 HALFBAND FILTER 4 HALFBAND FILTER 3 HALFBAND FILTER 2 HALFBAND FILTER 1 -40 -60 HALFBAND FILTER 5 -80 HALFBAND FILTER 4 HALFBAND FILTER 3 HALFBAND FILTER 2 HALFBAND FILTER 1 -100 -100 -120 -120 0.125 0.25 0.375 0.5 0.125 0.25 0.375 0.5 NORMALIZED FREQUENCY (FN) NORMALIZED FREQUENCY (FN) FIGURE 19. HALFBAND FILTER ALIAS CONSIDERATIONS FIGURE 18. HALFBAND FILTER FREQUENCY RESPONSE 15 HSP50214 TABLE 4. HALFBAND FILTER COEFFICIENTS COEFFICIENTS HALFBAND #1 HALFBAND #2 HALFBAND #3 HALFBAND #4 HALFBAND #5 C0 - 0.031303406 0.005929947 -0.00130558 -0.000378609 -0.000347137 C1 0.000000000 0.000000000 -0.000000000 -0.000000000 -0.000000000 C2 0.281280518 -0.049036026 -0.012379646 -0.003810883 -0.00251317 C3 0.499954224 0.000000000 -0.000000000 -0.000000000 -0.000000000 C4 0.281280518 0.29309082 -0.06055069 -0.019245148 -0.010158539 C5 0.000000000 0.499969482 -0.000000000 -0.000000000 -0.000000000 C6 - 0.031303406 0.29309082 -0.299453735 -0.069904327 -0.03055191 C7 0.000000000 -0.499954224 -0.000000000 -0.000000000 C8 -0.049036026 -0.299453735 -0.304092407 -0.081981659 C9 0.000000000 -0.000000000 -0.500000000 -0.000000000 C10 0.005929947 -0.06055069 -0.304092407 -0.309417725 C11 -0.000000000 0.000000000 -0.500000000 C12 -0.012379646 -0.069904327 -0.309417725 C13 -0.000000000 -0.000000000 -0.000000000 C14 -0.00130558 -0.019245148 -0.081981659 C15 -0.000000000 -0.000000000 C16 -0.003810883 -0.03055191 C17 -0.000000000 -0.000000000 C18 -0.000378609 -0.010158539 C19 -0.000000000 C20 -0.00251317 C21 -0.000000000 C22 -0.000347137 NOTE: While Halfband filters are typically selected starting with the last stage in the filter chain to give the maximum alias free bandwidth, a higher throughput rate may be obtained using other filter combinations. See Application Note 9720, “Calculating Maximum Processing Rates of the PDC”. Depending on the number of halfbands used, PROCCLK must operate a some minimum rate above the input sample rate, FS, to the halfband. This relationship depends on the number of multiplies for each of the halfband filter stages. The filter calculations take 3, 4, 5, 6, and 7 multiplies per input for HB1, HB2, HB3, HB4, and HB5 respectively. If we keep the assumption that fS is the input sampling frequency, then Equation 10 shows the minimum ratio needed. where: HB1 = 1 if this section is selected and 0 if it is bypassed; HB2 = 1 if this section is selected and 0 if it is bypassed; HB3 = 1 if this section is selected and 0 if it is bypassed; HB4 = 1 if this section is selected and 0 if it is bypassed; HB5 = 1 if this section is selected and 0 if it is bypassed; T = number of Halfband Filters Selected. The range for T is from 0 to 5. fPROCCLK/fS ≥ ([(7)(HB5)(2HB5)+ Examples of PROCCLK Rate Calculations (6)(HB4)(2(HB4 + HB5))+ Suppose we enable HB1, HB3, and HB5. Using Figure 16, HB1= 1, HB3 = 1, and HB5 = 1. Since stage 2 and stage 4 are not used, HB2 and HB4 = 0. PROCCLK must operate faster than (7x2+5x4+3x8)/8 = 7.25 times faster than fS. (5)(HB3)(2(HB3+HB4+HB5))+ (4)(HB2)(2(HB2+HB3+ HB4+HB5))+ (3)(HB1)(2(HB1+HB2+HB3+HB4+HB5))]/2T If all five halfbands are used, then PROCCLK must operate at (7x2+6x4+5x8+4x16+3x32)/32 = 7.4375 times faster than fS . (EQ. 10) 16 HSP50214 255-Tap Programmable FIR Filter TA PS = ( floor [ PROCCLK ⁄ ( F SAMP ⁄ R ) – R ] ) ( 1 + SYM ) – [ ( SYM ) ( ODD# ) ] COEFFICIENT VALUE For real filter configurations, use Equation 11 to calculate the number of taps available at a given input filter sample rate. (EQ. 11A) for real filters, and TA PS = floor [ (PROCCLK ⁄ ( F SAMP ⁄ R ) – ( R ] ⁄ 2 )] CN-1 COEFFICIENT NUMBER EVEN SYMMETRIC EVEN TAP FILTER CN-1 C0 COEFFICIENT NUMBER EVEN SYMMETRIC ODD TAP FILTER C0 CN-1 COEFFICIENT NUMBER CN-1 COEFFICIENT NUMBER ODD SYMMETRIC EVEN TAP FILTER CN-1 C0 COEFFICIENT NUMBER ODD SYMMETRIC ODD TAP FILTER C0 CN-1 COEFFICIENT NUMBER ASYMMETRIC ODD TAP FILTER (EQ. 11B) REAL FILTERS IMAGINARY COEFFICIENT VALUE CQ Use Equation 12 to calculate the maximum input rate. CQ(N-1) COEFFICIENT NUMBER CQ(0) CI(N-1) (EQ. 12A) CI(0) REAL C ( SYM ) ( ODD# ) ] ⁄ ( 1 + SYM ) ] ] OEFFIC CI LUE IENT VA COMPLEX FILTERS for real filters, and F SAMP = [ ( PROCCLK ) ( R ) ] ⁄ [ R + floor [ ( Ta ps ) ( 2 ) ] ] (EQ. 12B) Definitions: for complex filters, where floor[x], PROCCLK, FSAMP, R = Decimation Rate, SYM, and ODD# are defined as in Equation 11. Use Equation 13 to calculate the maximum output sample rate for both real and complex filters. F FIR OUT = ( F SAMP ) ⁄ R C0 ASYMMETRIC EVEN TAP FILTER for complex filters, where floor is defined as the integer portion of a number; PROCCLK is the compute clock; FSAMP = the FIR input sample rate; R = Decimation Rate; SYM = 1 for symmetrical filter, 0 for asymmetrical filter; ODD# = 1 for an odd number of filter taps, 0 = an even number of taps. F SAMP = ( PROCCLK ) ( R ) ⁄ [ R + [ floor [ ( Ta ps ) + C0 COEFFICIENT VALUE COEFFICIENT VALUE Additionally, the Programmable FIR filter provides for decimation rates, R, from 1 to 16. The processing rate of the Filter Compute Engine is PROCCLK. As a result, the frequency of PROCCLK must exceed a minimum value to insure that a filter calculation is complete before the result is required for output. In configurations which do not use decimation, one input sample period is available for filter calculation before an output is required. For configurations which employ decimation, up to 16 input sample periods may be available for filter calculation. COEFFICIENT VALUE COEFFICIENT VALUE The Programmable FIR filter can be used to implement real filters with even or odd symmetry, using up to 255 filter taps, or complex filters with up to 64 taps. The FIR filter takes advantage of symmetry in coefficients by summing data samples that share a common coefficient, prior to multiplication. In this manner, two filter taps are calculated per multiply accumulate cycle. Asymmetric filters cannot share common coefficients, so only one tap per multiply accumulate cycle is calculated. The filter can be effectively bypassed by setting the coefficient C0 = 1 and all other coefficients, CN = 0. COEFFICIENT VALUE using Control Word 17 bit 9, then coefficients are loaded starting with the center coefficient in Control Word 128 and proceed to last coefficient in Control Word 128+n. The filter symmetry type can be set to even or odd symmetric, and the number of filter coefficients can be even or odd, as illustrated in Figure 20. Note that complex filters can also be realized but are only allowed to be asymmetric. Only the coefficients that are used need to be loaded. (EQ. 13) Even Symmetric: Odd Symmetric: Asymmetric: Even Tap filter: Odd Tap filter: Real Filter: Complex Filters: h(n) = h(N-n-1) for n = 0 to N-1 h(n) = -h(N-n-1) for n = 0 to N-1 a filter with no coefficient symmetry a filter where N is an even number a filter where N is an odd number a filter implemented with real coefficients a filter with quadrature coefficients FIGURE 20. DEMONSTRATION OF DIFFERENT TYPES OF DIGITAL FIR FILTERS CONFIGURED IN THE PROGRAMMABLE DOWNCONVERTER The coefficients are 22 bits and are loaded using writes to Control Words 128 through 255 (see Microprocessor Write Section). For real filters, the same coefficients are used by I and Q paths. If the filter is configured as a symmetric filter 17 HSP50214 Automatic Gain Control (AGC) 6 The AGC section provides gain to small signals, after the large signals and out-of-band noise have been filtered out, to ensure that small signals have sufficient bit resolution in the Re-Sampling/Interpolating Halfband filters and the Output Formatter. The AGC can also be used to manually set the gain. The AGC optimizes the bit resolution for a variety of input amplitude signal levels. The AGC loop automatically adds gain to bring small signals from the lower bits of the 26bit programmable FIR filter output into the 16-bit range of the output section. Without gain control, a signal at -72dBFS = 20log10(2-12) at the input would have only 4 bits of resolution at the output (12 bits less than the full scale 16 bits). The potential increase in the bit resolution due to processing gain of the filters can be lost without the use of the AGC. GAIN - LINEAR AND dB 5 –8 ], 3 G (LINEAR) 2 0 0 FIGURE 21. AGC MULTIPLIER LINEAR AND dB TRANSFER FUNCTION 100 N = 15 N = 13 80 N = 12 N = 11 70 N = 10 N=9 GAIN (dB) 60 N=8 50 N=7 N=6 40 N=5 N=4 30 N=3 20 10 where N, the shifter exponent, has a range of 0>N>15 and X, the mantissa, has a range of 0>X>(28-1). 0 N=2 N=1 N=0 0 64 128 192 AGC CONTROL WORD (MANTISSA x 256) Equation 14 can be expressed in dB, N N = 14 90 (EQ. 14) (AGC Mult/Shift Gain)dB = 20log 10 ( 2 [ 1 + ( X )2 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 AGC CONTROL MANTISSA VALUES (TIMES 256) The AGC Multiplier/Shifter portion of the AGC is identified in Figure 23. The gain control from the AGC loop filter is sampled when new data enters the Multiplier/Shifter. The limit detector detects overflow in the shifter or the multiplier and saturates the output of I and Q data paths independently. The shifter has a gain from 0 to 90.31dB in 6.021dB steps, where 90.31dB = 20log10(2N), when N = 15. The mantissa provides an additional 6dB of gain in 0.0338dB steps where 6.004dB = 20log10[1+(X)2-8], where X = 28-1. Thus, the AGC multiplier/shifter transfer function is expressed as: N G (dB) 1 Figure 23 shows the block diagram for the AGC Section. The FIR filter data output is routed to the Re-Sampling and Halfband filters after passing through the AGC multipliers and shift registers. The outputs of the Interpolating Halfband filters are routed to the Cartesian to Polar coordinate converter. The magnitude output of the coordinate converter is routed through the AGC error detector, the AGC error scaler and into the AGC loop filter. This filtered error term is used to drive the AGC multiplier and shifters, completing the AGC control loop. AGC Mult/Shift Gain = 2 [ 1 + ( X )2 4 –8 FIGURE 22. AGC GAIN CONTROL TRANSFER FUNCTION ]) (EQ. 14A) The Cartesian to Polar Coordinate converter accepts I and Q data and generates magnitude and phase data. The magnitude output is determined by the equation: The full AGC range of the Multiplier/Shifter is from 0 to 96.314dB (20log10[1+(28-1)2-8] + 20log10[215] = 96.314). Figure 21 illustrates the transfer function of the AGC multiplier versus mantissa control for N = 0. Figure 22 illustrates the complete AGC Multiplier/Shifter Transfer function for all values of exponent and mantissa control. ˙2 2 r = 1.64676 I + Q . (EQ. 15) where the magnitude limits are determined by the maximum I and Q signal levels into the Cartesian to Polar converter. Taking fractional 2’s complement representation, magnitude ranges from 0 to 2.329, where the maximum output is ˙ 2 2 r = 1.64676 ( 1.0 ) + ( 1.0 ) = 1.64676 × 1.414 = 2.329 . The AGC loop feedback path consists of an error detector, error scaling, and an AGC loop filter. The error detector subtracts the magnitude output of the coordinate converter from 18 HSP50214 the programmable AGC THRESHOLD value. The bit weighting of the AGC THRESHOLD value (Control Word 8, bits 1628) is shown in Table 5. Note that the MSB is always zero. The range of the AGC THRESHOLD value is 0 to 7.9995. The AGC Error Detector output has the identical range. TABLE 6A. AGC LIMIT EXPONENT vs GAIN GAIN(dB) EXPONENT MANTISSA 96.330 15 511 90.309 15 0 84.288 14 0 78.268 13 0 72.247 12 0 66.227 11 0 60.206 10 0 54.185 9 0 48.165 8 0 42.144 7 0 36.124 6 0 30.103 5 0 24.082 4 0 18.062 3 0 12.041 2 0 6.021 1 0 0.000 0 0 TABLE 5. AGC THRESHOLD (CONTROL WORD 8) BIT WEIGHTING 28 27 26 25 24 23 22 21 20 19 18 17 16 22 21 20. 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 The loop gain is set in the AGC Error Scaling circuitry, using the two programmable mantissas and exponents. The mantissa, M, is a 4-bit value which weights the loop filter input from 0.0 to 0.9375. The exponent, E, defines a shift factor that provides additional weighting from 20 to 2-15 Together the mantissa and exponent define the loop gain as given by, AGC Loop Gain = M LG 2 –4 2 – ( 15 – E LG ) (EQ. 16) where MLG is a 4-bit binary value ranging from 0 to 15, and ELG is a 4-bit binary value ranging from 0 to 15. Table 7 and 8 detail the binary values and the resulting scaling effects of the AGC Scaling mantissa and exponent. The composite (shifter and multiplier) AGC scaling Gain range is from 0.0000 to 2.329(0.9375)20 = 0.0000 to 2.18344. The scaled gain error can range (depending on threshold) from 0 to 2.18344, which maps to a “gain change per sample” range of 0 to 3.275dB/sample. TABLE 6B. AGC LIMIT MANTISSA vs GAIN GAIN(dB) EXPONENT MANTISSA 6.000 0 509 5.750 0 480 The AGC Gain mantissa and exponent values are programmed into Control Word 8, bits 0-15. The PDC provides for the storing of two values of AGC Scaling Gain (both exponent and mantissa). This allows for quick adjustment of the loop gain by simply asserting the external control line AGCGNSEL. When AGCGNSEL = 0, then AGC GAIN 0 is selected, and when AGCGNSEL = 1, AGC Loop Gain 1 is selected. Possible applications include acquisition/tracking, no burst present/burst present, strong signal/weak signal, track/hold, or fast/slow AGC values. 5.500 0 452 5.250 0 425 5.000 0 398 4.750 0 372 4.500 0 347 4.250 0 323 4.000 0 299 3.750 0 276 3.500 0 254 The AGC loop filter consists of an accumulator with a built in limiting function. The maximum and minimum AGC gain limits are provided to keep the gain within a specified range and are programed by 12-bit control words using the following the equation: 3.250 0 232 3.000 0 211 2.750 0 190 2.500 0 170 2.250 0 151 2.000 0 132 1.750 0 114 1.500 0 96 1.250 0 79 1.000 0 62 0.750 0 46 0.500 0 30 0.250 0 14 0.020 0 1 AGC Gain Limit = ( 1 + m AG C 2 –9 )2 e (EQ. 17) ( AGC Gain Limit )dB = ( 6.02 ) ( eeee ) + 20 log ( 1.0 + 0.eeeeeeee ) (EQ. 17A) where m is an 8-bit mantissa value between 0 and 511, and e is the 4-bit exponent ranging from 0 to 15. Control Word 9, bits 16-27 are used for programming the upper limit, while bits 011 are used to program the lower threshold. The ranges and format for these limit values are shown in Tables 6A - C. The bit weightings for the AGC Loop Feedback elements is detailed in Table 9. TABLE 6C. AGC LIMIT DATA FORMAT CONTROL WORD 9 BIT: 27 26 25 24 23 22 21 20 19 18 17 16 FORMAT e e e e m m m m m m m m 19 HSP50214 SHIFT LIMITER 13 + 13 EXP MANTISSA 4 MSB = 0 LIMIT DET EXP=2NNNN 9 MANTISSA = 01.XXXXXXX(XXXXXXX)†† ∆ UNSIGNED † THRESHOLD TTT.TTTTTTTTTT EXP † MAN † LOOP GAIN 1 AGC REGISTER 1 13 AGC REGISTER 0 LOOP GAIN 0 UPPER LIMIT † LOWER LIMIT † 4 4 AGCGNSEL EXP † µP MSB = 0 MAN † 16 REGISTER 16 REGISTER SERIAL OUT AGC ERROR DETECTOR AGC ERROR SCALING (RANGE = 0 TO 2.18344) AGC LOOP FILTER MAGNITUDE (RANGE = 0 TO 2.3) LIMIT DET LIMITER 26 IFIR SHIFTER (RANGE = 0 TO 1) 18 18 IAGC RE-SAMPLING FIR FILTERS AND INTERPOLATING HALFBAND FILTERS 26 18 LIMITER QFIR SHIFTER LIMIT DET 18 CARTESIAN TO POLAR COORDINATE CONVERTER (G = 1.64676) QAGC AGC MULTIPLIER/SHIFTER † Controlled via microprocessor interface. † † Indicates additional resolution of the A version. FIGURE 23. AGC BLOCK DIAGRAM maximum AGC gain error by the loop gain. The expected range for the AGC rate is ~ 0.00004 to 1.23dB/symbol time for a threshold of 1/2 scale. See the notes at the bottom of Table 9 for calculation of the AGC Response times. The maximum AGC Response is given by: Using AGC loop gain, the AGC range, and expected error detector output, the gain adjustments per output sample for the loop filter section of the Digital AGC can be given by: AGC Slew Rate = 1.5dB ( THRESH – ( MAG *1.64676 ) ) × ( M LG ) ( 2 – 4 – ( 15 – E LG ) ) 2 (EQ. 18) AGC Response Max = Input(Cart/Polar Gain)(Error Det Gain) ( AG C Loop Gain)(AGC Output Weighting) (EQ. 19) The loop gain determines the growth rate of the sum in the loop accumulator which, in turn, determines how quickly the AGC gain traces the transfer function given in Figures 21 and 22. Since the log of the gain response is roughly linear, the loop response can be approximated by multiplying the Since the AGC error is scaled to adjust the gain, the loop settles asymptotically to its final value. The loop settles to the mean of the signal. 20 HSP50214 Resampler/Halfband Filter TABLE 7. AGC LOOP GAIN BINARY MANTISSA TO GAIN SCALE FACTOR MAPPING BINARY CODE (MMMM) SCALE FACTOR BINARY CODE (MMMM) SCALE FACTOR 0000 0.0000 1000 0.5000 0001 0.0625 1001 0.5625 0010 0.1250 1010 0.6250 0011 0.1875 1011 0.6875 0100 0.2500 1100 0.7500 0101 0.3125 1101 0.8125 0110 0.3750 1110 0.8750 0111 0.4375 1111 0.9375 The Resampler is an NCO controlled polyphase filter that allows the output sample rate to have a non-integer relationship to the input sample rate. The filter engine can be viewed conceptually as a fixed interpolation filter, followed by an NCO controlled decimator. The prototype polyphase filter has 192 taps designed at 32 times the input sample rate. Each of the 32 phases has 6 filter taps (6)(32) = 192. The stopband attenuation of the prototype filter is greater than 60dB, as shown in Figure 24. The signal to total image power ratio is approximately 55dB, due to the aliasing of the interpolation images. The filter is capable of decimation rates from 1 to 4. If the output is at least 2x the baud rate, the 32 interpolation phases yield an effective sample rate of 64x the baud rate or approximately 1.5%, (1/64), maximum timing error. Following the Resampler are two interpolation halfband filters. The halfband filters allow the user to up-sample by 2 or 4 to recover time resolution lost by decimating. Interpolating by 2 or 4 gives 1/4 or 1/8 baud time resolution (assuming 2x baud at the Resampler output). The halfband filters use the same coefficients as HB3 and HB5 from the Halfband Filters Section. If one halfband is used, the 23-tap filter is chosen. If two are used, the 23-tap filter runs first followed by the 15-tap filter operating at twice the first halfband’s rate. The 23-tap filter requires 7 multiplies, and the 15-tap filter requires 5 multiplies to complete a filter calculation. TABLE 8. AGC LOOP GAIN BINARY EXPONENT TO GAIN SCALE FACTOR MAPPING BINARY CODE (EEEE) SCALE FACTOR BINARY CODE (EEEE) SCALE FACTOR 0000 215 1000 27 0001 214 1001 26 0010 213 1010 25 0011 212 1011 24 0100 211 1100 23 0101 210- 1101 22 0110 29 1110 21 0111 28 1111 20 Using the interpolation halfband filters allows for reduction in the FIR filter sample rate. This optimizes the use of the programmable FIR filter by allowing the FIR output sample rate to be closer to the Nyquist rate of the desired bandwidth. Optimizing the FIR filter performance provides better use of the programmable FIR taps. Table 10 details the maximum clocking rates for the possible re-sampling and interpolation halfband filter configurations of this section of the PDC. Control Word 16, bits 2-0 identify the filter configuration. Control Word 16, bit 3 is used to bypass the polyphase Resampler filter. For proper data output from the interpolation filters, the data ready signal must account for the re-sampling and interpolation processes. Figure 25 illustrates the insertion of additional data ready pulses to provide sufficient pulses for the new output sample rate. The Resampler Output Pulse Delay parameter is set in Control Word 16, bits 4-11. These bits set the delay between the output samples when interpolation is utilized. Program this distance between pulses using For example, if MLG = 0101 and ELG = 1100, the AGC Loop Gain = 0.3125*2-7. The loop gain mantissas and exponents are set in the AGC Loop Parameter control register (Control Word 8, bits 0-15). Two AGC loop gains are provided in the Programmable Down Converter, for quick adjustment of the AGC loop. The AGC Gain select is a control input to the device, selecting Gain 0 when AGCGNSEL = 0, and selecting Gain 1 when AGCGNSEL = 1. N = [ ( f PROCCLK /f OUT ) – 1 ] (EQ. 20) A value of at least 5 is required to have sufficient time to update the output buffer register. (Writing 5 samples requires 5 clock cycles) A value of at least 16 is required for proper serial output from the part. (Conversion from 16-bit parallel to serial) The value is programmed in numbers of PROCCLK’s. 21 HSP50214 . TABLE 9. BIT WEIGHTING FOR AGC LOOP FEEDBACK PATH AGC ACCUM BIT POSITION GAIN ERROR INPUT GAIN ERROR BIT WEIGHT AGC LOOP FILTER AGC LOOP GAIN FILTER GAIN MULTIPLIER (MANTISSA) (OUTPUT) AGC OUTPUT AND AGC AGC GAIN LIMITS BIT RESOLUTION WEIGHT (dB) SHIFT =0 SHIFT =4 SHIFT =8 SHIFT = 15 31 2 2 2 2 0 30 2 2 2 2 E 3 48 29 2 2 2 2 E 2 24 28 2 2 2 2 E 1 12 2 2 2 2 2 E 0 6 . 2 2 2 1 -1 3 2 2 2 . M M -2 1.5 27 12 =2 26 11 =1 25 10 24 9 =1 x 1 2 2 2 1 M -3 0.75 23 8 =2 x 2 2 2 2 2 M -4 0.375 22 7 =3 x 3 2 2 2 3 M -5 0.1875 21 6 =4 x 4 2 2 2 4 M -6 0.09375 20 5 =5 5 2 2 2 5 M -7 0.04688 19 4 =6 6 2 2 1 X -8 0.02344 18 3 =7 7 2 2 . 6 7 -9 0.01172 17 2 =8 8 2 2 1 8 -10 0.00586 16 1 =9 9 2 2 2 9 -11 0.00293 15 0 = 10 10 2 1 10 -12 0.00146 14 11 2 . 3 4 11 -13 0.000732 13 12 2 1 5 12 -14 0.000366 12 13 2 2 6 13 -15 0.000183 11 14 1 . 3 7 14 -16 0.0000916 4 8 G -17 0.0000458 . =0 . 0 1 0 10 0 0 0 0 9 1 5 9 G -18 0.0000229 8 2 6 10 G -19 0.0000114 7 3 7 11 G -20 0.00000572 6 4 8 12 G -21 0.00000286 5 5 9 13 G 4 6 10 14 G 3 7 11 G G 2 8 12 G G 1 9 13 G G 0 10 14 G G AGC ResponseMax = Input(Cart/PolarGain)(Error Det Gain)(AGC Loop GainMax)(AGC Output Weighting). AGC ResponseMax = (1)(1.64676)(2-0)(1)(0.75dB) ~ 1.23dB/symbol time. AGC ResponseMin = (1)(1.64676)(2-15)(1)(0.75dB) ~ 0.00004dB/symbol time. Thus, the expected range for the AGC rate is ~ 0.00004 to 1.23dB/symbol time. 22 HSP50214 TABLE 10. POLYPHASE AND INTERPOLATING HALFBAND FILTER MAXIMUM CLOCKING RATES 0 CLOCK CYCLES RESAMPLER INPUT RATE (MHz) INTERPOLATION RATE MAGNITUDE (dB) -20 -40 MODE -60 OUTPUT RATE (MHz) Bypass 0 35.00 - 28.00 -80 Polyphase Filter 6 35/6 = 5.83 - NCO ≤ 5.83 -100 Polyphase and 1 Halfband Filter 13 35/13 = 2.69 2 NCO ≤ 5.38 Polyphase and 2 Halfband Filters 23 35/23 = 1.52 4 NCO ≤ 6.09 1 Halfband Filter 7 35/7 = 5.00 2 10.00 2 Halfband Filters 17 35/17 = 2.059 4 8.24 -120 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FREQUENCY (RELATIVE TO fIN) FIGURE 24A. POLYPHASE RESAMPLER FILTER BROADBAND FREQUENCY RESPONSE 10 0 POLYPHASE RESAMPLER FILTER -20 HALFBAND FILTER #1 HALFBAND FILTER #2 -30 MUX MAGNITUDE (dB) -10 -40 RESAMPLER NCO -50 -60 PULSE DELAY -70 PULSE DELAY COUNTER PROCCLK 1 FREQUENCY (RELATIVE TO fIN) FIGURE 24B. POLYPHASE RESAMPLER FILTER PASS BAND FREQUENCY RESPONSE THIS BLOCK GENERATES EXTRA DATA READY PULSES FOR THE NEW OUTPUTS FROM THE INTERPOLATION PROCESS. 2 1 MAGNITUDE (dB) 0 HB1 RSMPLR PROCCLK/N HB2 0.875 0.9375 0.75 0.8125 0.625 0.6875 0.5625 0.5 0.375 0.4375 0.3125 0.25 0.125 0.1875 0 0.0625 -80 # EXTRA PULSES 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 BYPASS 0 1 1 3 (NV) 3 (NV) 3 3 0 1 0 1 0 1 0 1 -1 NV = INVALAID MODE -2 FIGURE 25. GENERATING DATA READY PULSES FOR OUTPUT DATA -3 -4 In burst systems (such as TDMA), time resolution is needed for quickly identifying the optimum sample point. The timing is adjusted by shifting the decimation in the DSP µP to the closest sample. Use of timing error rate in this way may yield a faster acquisition than a phase-locked loop coherent bit synchronization. Finding the optimum sample point minimizes intersymbol interference. -5 -6 -7 -8 -9 0.5 0.4375 0.375 0.3125 0.25 0.1875 0.125 0.0625 0 -10 Fine time resolution is needed in CDMA systems to resolve different multipath rays. In CDMA systems, the demands on the programmable FIR can only be relieved by the Resampler/interpolation halfband filters. Assume the chip rate for a baseband CDMA system is 1.2288MHz and PROCCLK is limited to 35MHz. Using the symmetric filter pre-sum approach, PROCCLK limits the programmable FIR to 70MIPS (millions FREQUENCY (RELATIVE TO fIN) FIGURE 24C. POLYPHASE RESAMPLER FILTER EXPANDED RESOLUTION PASSBAND FREQUENCY RESPONSE 23 HSP50214 trol (Control Word 11, bit 1), a Timing NCO Phase Accumulator Load On Update control (Control Word 11, bit 0), the Timing NCO Center Frequency (Control Word 12), a Timing Phase Offset (Control Word 13, bits 0-7), a Timing Frequency Strobe (Control Word 14) and a Timing Phase Strobe (Control Word 15). Refer to the Carrier Synthesizer Mixer section for a detailed discussion of the serial interface for the Timing NCO offset frequency word. of instructions per second) effective due to symmetry. If the CDMA filter (loaded into the programmable FIR section) requires an impulse response with a span of 12 chips, the filter at 2x the chip-rate would need 24 taps. The 24 taps would translate into 59MIPS = (1.2288MHz)(2)(24). To get the same filtering at 8x the chip rate would require 944MIPS = (1.2288MHz)(8)(96). Direct 8x filtering can not be accomplished with the programmable filter alone because 944MIPS are much greater that the 60MIPs effective limit set by PROCCLK. It is necessary to decimate down to 2x the chip rate to get a realistic number of filter taps. Both interpolation halfband filters are used to obtain an 8x CDMA output. The MIPS for the first halfband equals (2.4576MHz)(Number of Multiplies for first halfband), and the second equal (4.9152MHz)(Number of Multiplies for second halfband). Combined halfband filters is equal to (1.2228MHz)(4)(48) = 236MIPS. Thus the MIPS are 18 and 25 for the first and second halfbands respectively, and 42 for both. A timing error detector is provided for measuring the phase difference between the timing NCO and a external clock input, REFCLK. Timing Error is generated by comparing the values of two programmable counters. One counter is clocked with the Timing NCO carry out and the other is clocked by the REFCLK. The 12-bit NCO Divide parameter is set in Control Word 18, bits 16-27. The NCO Divide parameter is the preload to the counter that is clocked by the Timing NCO carry out. The 12-bit Reference Divide parameter is set in Control Word 18, bits 0-11, and is the preload for the counter that is clocked by the Reference clock. Figure 27 details the block diagram of the timing error generation circuit. The 16 bits of timing error are available both as a PDC serial output and as a processor read parameter. See the Processor Read Section for more details on accessing this value. Timing NCO The Timing NCO is very similar to the carrier NCO phase accumulator section. It provides the NCO driven sample pulse and associated phase information to the re-sampling filter process described in the Resampler Filter section. The Timing NCO does not include the SIN/COS section found in the Carrier NCO. The top level block diagram is shown in Figure 26. REG TIMING NCO PHASE OFFSET † 8 CARRY OUT = RUN FILTER STROBE PROGRAMMABLE DIVIDER 12 4 0 REG REFERENCE DIVIDE † CLEAR PHASE ACC † MUX REFCLK TE(15:0) + + PHASE ACCUMULATOR ∆ 5 (NCO DIVIDE)/2 † REG † REG TIMING PHASE STROBE PHASE(31:28) FILTER PHASE SELECT SYNC CARRY NCO DIVIDE† † EN EXT TIMING NCO SYNC SYNCIN2 TIMING NCO ACC EN PROGRAMMABLE DIVIDER + ENABLE SOF † MUX 32 SOF SOFSYNC SOF TIMING NCO PH ACC LOAD ON UPDATE† 32 SCF 0 REG REG REG † Controlled via microprocessor interface. FIGURE 27. TIMING ERROR GENERATION Figure 27A illustrates an application where the Timing Error Generator is used to lock the receiver samples with a transmit data rate. In this example, the receive samples are at four times the transmit data rate. An external loop filter is required, whose frequency error output is fed into the Timing NCO. This allows the loop to track out the long term drift between the receive sample rate and the transmit data clock. SYNC TIMING FREQ STROBE † SYNC SHIFT REG NUMBER OF SOF BITS † TIMING NCO CENTER FREQUENCY † † Controlled via microprocessor interface. FIGURE 26. TIMING NCO BLOCK DIAGRAM The programmable parameters for the Timing NCO include an Enable External Timing NCO Sync (Control Word 11, bit 5), the serial word width, Number of Offset Frequency Bits (Control Word 11 bits 3-4), an Enable Offset Frequency control (Control Word 11, bit 2), a Clear NCO Accumulator con- 24 HSP50214 TABLE 11. MAG/PHASE BIT WEIGHTING LOOP FILTER MAGNITUDE 15 (MSB) 22 Always 0 180 14 21 90 13 20 45 12 2-1 22.5 11 2-2 11.25 10 2-3 5.625 9 2-4 2.8125 8 2-5 1.40625 7 2-6 0.703125 6 2-7 0.3515625 5 2-8 0.17578125 4 2-9 0.087890625 3 2-10 0.043945312 2 2-11 0.021972656 1 2-12 0.010986328 0 (LSB) 2-13 0.005483164 µP CLKIN/RT (NCO DIVIDE)/2 † NCO DIVIDE = 4N† PROGRAMMABLE DIVIDER ∆ 12 + 4 REFERENCE DIVIDE = N † TX DATA CLK (REFCLK) TE(15:0) REG CARRY PHASE(31:28) TIMING NCO ACC. EN PROGRAMMABLE DIVIDER TO TX BLOCK (MODULATOR) RT = TOTAL DECIMATION (CIC, HB FILTERS AND FIR) † Controlled via microprocessor interface. PHASE (o) BIT FIGURE 27A. TIMING ERROR APPLICATION π/2 4000 3fff +π/2 Cartesian to Polar Converter 4000 The Cartesian to Polar converter computes the magnitude and phase of the I/Q vector inputs. The I and Q inputs are 16 bits. The converter phase output is 18 bits (truncated) with the 16 MSB’s routed to the output formatter and all 18 bits routed to the frequency discriminator. The 16-bit output phase can be interpreted either as two’s complement (-0.5 to approximately 0.5) or unsigned (0.0 to approximately 1.0), as shown in Figure 28. The phase conversion gain is 1/2π. The phase resolution is 16 bits. The 16-bit magnitude is unsigned binary format with a range from 0 to 2.32. The magnitude conversion gain is 1.64676. The magnitude resolution is 16 bits. The MSB is always zero. 3ff f Q 7fff ±π 8000 I 0000 0 ffff bfff c000 -π/2 Q 7fff π 8000 I 0000 0 ffff c000 bfff 3π/2 FIGURE 28. PHASE BIT MAPPING OF COORDINATE CONVERTER OUTPUT The magnitude and phase computation requires 17 clocks for full precision. At the end of the 17 clocks, the magnitude and phase are latched into a register to be held for the next stage, either the Output Formatter or frequency discriminator. If a new input sample arrives before the end of the 17 cycles, the results of the computations up until that time, are latched. This latching means that an increase in speed causes only a decrease in resolution. Table 12 details the exact resolution that can be obtained with a fixed number of clock cycles up to the required 17. The input magnitude and phase errors induced by normal SNR values will almost always be worse than the Cartesian to Polar conversion. Table 11 details the phase and magnitude weighting for the 16 bits output from the PDC. 25 HSP50214 TABLE 12. MAG/PHASE ACCURACY vs CLOCK CYCLES † CLOCKS MAGNITUDE ERROR (% fS) PHASE ERROR (DEG.)† PHASE ERROR (% fS) 6 0.065 3.5 2 7 0.016 1.8 1 8 0.004 0.9 0.5 9 <0.004 0.45 0.25 10 <0.004 0.22 0.12 11 <0.004 0.11 0.062 12 <0.004 0.056 0.03 13 <0.004 0.028 0.016 14 <0.004 0.014 0.008 15 <0.004 0.007 0.004 16 <0.004 0.0035 0.002 17 <0.004 0.00175 0.001 PHASE INPUT † † FIR COEFFICIENTS DISC. FIR DECIMATION FIR SYMMETRY TYPE FIR SYMMETRY FIR TAPS DELAY (1-8) † † † † † + 63-TAP FIR FILTER FREQ(15:0) † Controlled via microprocessor interface. FIGURE 29. FREQUENCY DISCRIMINATOR BLOCK DIAGRAM The discriminator input is 18 bits, and the output is rounded asymmetrically to 16 bits. The phase into the discriminator can be multiplied by 20, 21, 22, or 23 (modulo 2π) to remove PSK data modulation. All programmable parameters for the Frequency Discriminator are set in Control Word 17. Bits 15 and 16 are the phase multiplier which represents the shift applied to the input phase. For CW, the multiply should equal 20, (00). For BPSK, QPSK, and 8PSK, the multiply should equal 21, (01); 22, (10); or 23, (11); respectively. Bit 14 is used to enable or disable the discriminator. Bits 11-13 set the decimation in the programmable FIR filter. Bit 10 sets the filter symmetry type as either odd or even, bit 9 sets whether the filter is asymmetric or symmetric, and bits 3-8 set the number of FIR filter taps. Bits 0-2 set the number of delays in the frequency discriminator. The discriminator block delays phase from the Cartesian to Polar section and subtracts it from the latest sample. This delay and subtract can be modeled as a programmable delay comb filter. The output of the filter is dθ/dt, or frequency. The transfer function of the discriminator is set by (EQ. 21) where D is the programmable discriminator delay expressed in number of sample clock delays. The discriminator output frequency is then filtered with a programmable FIR filter. The block diagram of the Frequency Discriminator is shown in Figure 29. Output Section The output section routes the 7 types of processed signals to output pins in three basic modes. These basic modes are: Parallel Direct Output, Serial Direct Output, and the Buffer RAM Output. The Serial and Parallel Direct Output modes were designed to output data strobes and “real time” continuous streams of data. The Buffer RAM Output mode outputs data upon receipt of an asynchronous request from an external DSP processor or other baseband processing engine. The use of the interrupt signal from the Programmable Down Converter in conjunction with the request strobes from the controller ensures that data is transferred only when both the controller and the Programmable Down Converter are ready. The Buffer RAM output can be operated in a First In First Out (FIFO) or SNAPSHOT mode with the data output either via the 8-bit processor interface or a 16-bit processor interface. The range of delay in the discriminator is from 1 to 8 samples. Modulo 2π subtraction eliminates rollover problems in the subtraction at 2π. The alias free discriminator frequency range is given by: Range FREQDISC = CW ± F SAMPOUT ⁄ ( D + 1 ) ; DISCRIMINATOR DELAY DISCRIMINATOR EN + Frequency Discriminator –D † - Assumes ±180o = fS. H(z)= 1 – Z PHASE MULTIPLIER (EQ. 22) where D is the discriminator delay defined in Equation 21 (1 < D < 8), FSAMPOUT is the Discriminator FIR filter output sample rate and CW is the desired center frequency. When the phase multiplier is set to a value other than 20, the discriminator range is reduced proportionally. The phase multiplier can be 1, 2, 4 or 8 (20 to 23). Thus, a multiply of 21 reduces the range by 2, a multiply of 22 reduces the range by 4, and a multiply of 23 reduces the range by 8. The FIR filter can be configured with up to 63 symmetric taps and up to 32 asymmetric taps. In the symmetric mode, the FIR can be configured for even or odd symmetry, as well as with an even or odd number of filter taps. Decimation is provided to allow more processing time for longer (i.e., more taps) filter structures. 26 HSP50214 Parallel Direct Output Port Mode AOUT DIRECT PAR OUTPUT MODE DATA SOURCE † The Parallel Direct Output Port Mode outputs two 16-bit words, AOUT and BOUT, of “real time” data. Figure 30 details the parallel output circuitry. Selection of the data source for the AOUT and BOUT parallel outputs is done via Control Word 20, bits 22-23, and 20-21, respectively. The AOUT port can output I, Magnitude, or Frequency data. The BOUT port can output Q, Phase or Magnitude data. The upper bytes of AOUT and BOUT are always in the parallel direct mode. The 16-bit parallel direct mode is selected by setting Control Word 20, bit 25, to zero. The DATARDY output is asserted during the first clock cycle of new data on the AOUT bus. DATARDY MAG 16 FREQ 16 A(15:8) AOUT(15:8) A(7:0) RAM(15:8) MUX 16 MUX I AOUT(7:0) BOUT DIRECT PAR OUTPUT MODE DATA SOURCE † B(15:8) 16 16 MAG BOUT(15:8) B(7:0) RAM (7:0) MUX PHAS 16 MUX Q BOUT(7:0) RAM (15:0) DATA SOURCE FOR LSB † † Controlled via microprocessor interface. FIGURE 30A. PARALLEL OUTPUT BLOCK DIAGRAM PROCCLK I CHOSEN FOR AOUT I Q DATARDY R CHOSEN FOR AOUT R Q DATARDY (NOTE 1) 17 PROCCLK PERIODS DATARDY (NOTE 2) FREQ CHOSEN FOR AOUT FREQ Q T (NOTE 4) DATARDY (NOTE 3) NOTES: 1. Computation preempted by new data. 2. Computation completes. 3. If decimation is selected, the DATARDY signal will occur at 1/Deci times the I/Q output sample rate. 4. T is equal to the number of PROCCLK cycles needed to compute the discriminator FIR plus the delay from I/Q to R/φ plus 6. The delay will change depending on whether the Θ computation is preempted or not. FIGURE 30B. TIMING FOR PARALLEL OUTPUT NOTE: I and Q are sample aligned in time. |r| and φ are sample aligned in time, but one sample delayed from I or Q. The frequency sample is delayed in time from I or Q by 1 sample time + 63 tap FIR impulse response. If the FIR is set to decimate and frequencies selected for AOUT, the DATARDY signal will be at the documented rate. 27 HSP50214 Serial Direct Output Port Mode TABLE 13. LINKING CONTROL WORDS FOR SERIAL OUTPUT DATA TYPE IDENTIFIER The Serial Direct Output Port Mode offers the ability to construct two serial output data streams, SEROUTA AND SEROUTB, from 16-bit I, Q, magnitude, phase, frequency, timing error, and AGC level data words. The total number of data words (1 to 8) for serial output, and the sequential order of these data word components of the serial output are programmable. Each data word may be used once in either the SEROUTA or SEROUTB data streams. Figure 31 illustrates the conceptual implementation of the Serial Direct Output Port Mode. In the Serial Direct Mode, the output data is loaded into serial shift registers and routed to two serial output pins, SEROUTA and SEROUTB. The serial output shift clock, SERCLK, is PROCCLK divided by 1, 2, 4, 8, or 16. The divide down ratio is programmed using Control Word 20, bits 14-16. The data is shifted out on the rising edge of the internal SERCLK . The external clock polarity of SERCLK is programmable via Control Word 20, bit 18. A sync signal is provided for detection of the start or end of each word in the serial sequence. Control Word 20, Bit 17, sets the SERSYNC signal location as either preceding the MSB (typical for interfacing with microprocessors) or following the LSB (typical for interfacing to D/A converters). Control Word 20, bit 19, sets the SERSYNC polarity as active low or high. The LSB of each data word can be configured as either the true LSB data, or set at a fixed logic “1” or “0” for use as a tag bit. Control Word 20 bits 0-13 set the LSB of each of the 7 types of data words that can be configured in the serial output stream. Control Word 19, bits 21-24 set the number of serial data words that will be linked to form the serial outputs. Up to 7 data words can be linked to form the serial output. SEROUTA and SEROUTB will have an identical number of words in the serial output streams. DATA TYPE 000 I Data 001 Q Data 010 Magnitude (MAG) Data 011 Phase (PHAS) Data 100 Frequency (FREQ) Data 101 Timing Error (TIMERR) Data 110 AGC Gain 111 Zeros Two examples will illustrate the process of configuring a serial output using the Serial Output mode. Serial Output Configuration Example 1: It is desired to output the I data word, followed by the Q data word, followed by the Phase data word on the SEROUTA output. Similarly, it is desired to output the Magnitude data word followed by the Frequency data word, followed by the Timing Error data word, followed by the AGC Level data word on the SEROUTB output. Table 14 illustrates how Control Word 19 should be programmed. TABLE 14. EXAMPLE 1 SERIAL OUTPUT CONTROL SETTINGS CONTROL WORD 19 BIT POSITION FUNCTION BIT VALUE The 16-bit I, Q, magnitude, phase, frequency, timing error, AGC level, and “zeros” data words for are loaded into their respective shift registers. The Magnitude and AGC Level data word are unsigned binary format with a leading zero, while the remaining signals are 2’s complement format. 30-28 SEROUTA Data Source 000 (I) 27-25 SEROUTB Data Source 010 (|r|) 24-21 Number of Serial Word Links in a Chain 100 (4) Any of the eight data sources can be selected as the first serial word for SEROUTA or SEROUTB. Control Word 19, bits 25-30 set the data type for the first serial word for SEROUTA and SEROUTB. The three bit data type identifier is shown both in Table 13 and in Figure 30, to the right of the controls for the cross matrix switch. Serial output data word sequences are formed by linking data words by programming the data source for each shift requester’s shift input signal. This programming links the shift registers together in one or two serial chains. Thus the Control Word 19 term “Link follows X data”, where X is one of the seven data types. Once the data source data word is selected (by programming a three bit word representing one of the data types into Control Word 19, bits 25-27 (SEROUTA), and 28-30 (SEROUTB)), the process for identifying the next word is to select a three bit data type identifier which represents the data type to follow the source data type. Program these bits into the Control Word 19 field representing the “Link following X data”, where X = the source data type, defines the second word in the sequence. Likewise, the third data word is linked by selecting the Control Word 19 bits that identify the “Link following X data”, where X = the data type of the second word in the serial chain. The process continues until all the desired data words have been linked. 20-18 Link following I data 001 (Q) 17-15 Link following Q data 011 (φ) 14-12 Link following |r| data 100 (f) 11-9 Link following φ data 111 (Zeros) 8-6 Link following f data 101 (Timing) 5-3 Link following AGC data XXX (N/A) 2-0 Link following Timing Error data 110 (AGC) RESULT NOTE: Because all but the first data word in the serial output is identified by the data type that it follows, SEROUTB can only be fully independent of the sequence in SEROUTA if it does not use any of the same data word types. This implies a partition as described in Example 1. Once a data word that is used in SEROUTA is called out in SEROUTB, the remaining sequence in SEROUTB will be identical to that portion of SEROUTA sequence that follows the duplicate data type. This follows from using the “Link follows ‘data type’ data” for word linkage. NOTE: Each type of data word should be used only once in each data stream. If the “Link following I data” is programmed with the data type identifier for I, then the part will repeat the I data word until all of the data word locations are filled. In Example 1, if bits 20-18 were erroneously programmed to 000 (I data) then the SEROUTA would be four sequential repeats of the I data word. NOTE: I and Q are sample aligned in time. |r| and f are sample aligned in time, but one sample delayed from I or Q. The frequency sample is delayed in time from I or Q by 1 sample time + 63 tap FIR impulse response. If the FIR is set to decimate, the FIR output will be repeated every sample time until a new value appears at the filter output. (i.e., the frequency samples are clocked out at the I, Q sample rate regardless of decimation.) 28 HSP50214 The serial data stream looks like: SEROUTA: CONTROL WORD 19 FIELD SEROUTB: start CONTROL WORD 19 FIELD start I data word > SEROUTA source data = 000 |r| data word > SEROUTB source data = 010 Q data word > Link following I data = 001 f data word > Link following |r| data = 100 φ data word > Link following Q data = 011 TE data word> Link following f data = 101 Zero data word > Link following φ data = 111 AGC data word > Link following TE data = 110 end > end > I DATA SERIAL OUTPUT TAG BIT † Q DATA SERIAL OUTPUT TAG BIT † MAGNITUDE DATA SERIAL OUTPUT TAG BIT † PHASE DATA SERIAL OUTPUT TAG BIT † FREQUENCY DATA SERIAL OUTPUT TAG BIT † TIMING ERROR DATA SERIAL OUTPUT TAG BIT † AGC DATA SERIAL OUTPUT TAG BIT † DATA SOURCE FOR SEROUTA † LINK FOLLOWING I DATA † LINK FOLLOWING Q DATA † LINK FOLLOWING MAG DATA † LINK FOLLOWING PHASE DATA † LINK FOLLOWING FREQ DATA † LINK FOLLOWING TIMING DATA † LINK FOLLOWING AGC DATA † REG REG f (15:0) FOLLOWS Q SHIFT REG FOLLOWS |r| SHIFT REG CROSS MATRIX SWITCH SHIFT REG FOLLOWS φ CROSS MATRIX SWITCH SHIFT REG SHIFT REG FOLLOWS f SHIFT REG SHIFT REG FOLLOWS TE SHIFT REG SHIFT REG FOLLOWS AGC REG AGC (15:0) SHIFT REG SHIFT REG SHIFT REG REG TE (15:0) REG φ (15:0) REG |r| (15:0) REG Q (15:0) SOURCE I Q MAG PHASE FREQUENCY TIMING ERROR AGC ZERO FOLLOWS I SHIFT REG REG I (15:0) XXX 000 001 010 011 100 101 110 111 SHIFT REG SHIFT REG SEROUTA ZERO SOURCE MUX 6 5 4 3 2 1 0 SERIAL OUTPUT SHIFT REGISTER DATA SOURCE FOR SEROUTB † SEROUTA SEROUTB SOURCE 6 PROCCLK PROGRAMMABLE DIVIDER 5 4 3 2 1 0 SERIAL OUTPUT SHIFT REGISTER SEROUTB NUM OF SER WORD LINKS IN A CHAIN † SERIAL OUT CLOCK DIVIDER † SERIAL OUTPUT SYNC POSITION † SERIAL OUTPUT CLOCK POLARITY † SERIAL OUTPUT SYNC POLARITY † † Controlled via microprocessor interface ‡ Polarity is programmable FIGURE 31. SERIAL OUTPUT FORMATTER BLOCK DIAGRAM 29 ‡ SERCLK ‡ SERSYNC HSP50214 Serial Output Configuration Example 2: SEROUTB: It is desired to output only three data words on each serial output. The I data word, followed by the Q data word, followed by the Magnitude data word is to be output on SEROUTA. The Q data word followed by the Magnitude data word, followed by the one other data word to be output on SEROUTB. The choices for the remaining data word in the SEROUTB signal are: phase, frequency, AGC level and timing error. Table 15 illustrates how Control Word 19 should be programmed. start FUNCTION BIT VALUE 30-28 SEROUTA Data Source 000 (I) 27-25 SEROUTB Data Source 001 (Q) 24-21 Number of Serial Word Links in a Chain 011 (3) 20-18 Link following I data 001 (Q) 17-15 Link following Q data 010 (|r|) 14-12 Link following |r| data TBD TBD 11-9 Link following φ data XXX (N/A) 8-6 Link following f data XXX (N/A) 5-3 Link following AGC data XXX (N/A) 2-0 Link following Timing Error data XXX (N/A) RESULT SEROUTA source data = 000 Link following I data = 001 |r|data word > Link following Q data = 010 TBD data word> Link following |r| data = TBD As previously discussed, Control Word 20, bits 17 and 19, set the functionality of the LSB of each data word. These bits may be programmed to be either a logic “0”, logic “1” or as normal data. The fixed states are designed to allow the microprocessor to synchronize to the serial data stream. CONTROL WORD 19 FIELD Q data word > Link following Q data = 010 The other signals provided with the SEROUTA and SEROUTB are the SERSYNC and the SERCLK. The SERSYNC signal can be programmed in either early or late sync mode. The sync signal is pulsed active low or active high for each information word link of the chain of data created using control word 19. Figure 33 shows the four possible configurations of SERSYNC as programmed using Control word 20. start I data word > SEROUTB source data = 001 |r|data word > As shown by this example, once Q was linked to |r| in the SEROUTA chain, the SEROUTB chain must have |r| following Q, if Q is selected. Figure 32 illustrates the construction of the serial output streams. If the serial data stream was changed to be a length of four data words, then, by default, the SEROUTA would be whatever is selected for SEROUTB data word 3. SEROUTB would need to identify the fourth data word. Thus, SEROUTA and SEROUTB are not fully independent because they share the Q data word (and by default, the MAGNITUDE follows Q data link and whatever is selected for data word 3 to follow MAGNITUDE data in SEROUTB). The serial data stream looks like: SEROUTA: Q data word > end > TABLE 15. EXAMPLE 2 SERIAL OUTPUT CONTROL SETTINGS CONTROL WORD 19 BIT POSITION CONTROL WORD 19 FIELD end > CONTROL WORD 19 BITS 24-21 = 011 (3 DATA WORDS IN EACH SERIAL OUTPUT) DATA WORD 3 DATA WORD 2 DATA WORD 1 MAGNITUDE Q I DATA WORD 3 DATA WORD 2 DATA WORD 1 TBD MAGNITUDE Q THE REMAINING CHOICES FOR THE THIRD LINK ON SEROUTB ARE: PHASE, FREQUENCY, AGC LEVEL, AND TIMING ERROR SEROUTB NOTE: Once magnitude is identified to follow Q, it must be that way on both serial outputs. FIGURE 32. EXAMPLE 2 SERIAL OUTPUT DATA STREAM 30 SEROUTA HSP50214 “NORMAL” 0 1 2 1 2 LATE SERSYNC MODE SERSYNC FOLLOWS LSB 0 “INVERTED” 1 “NORMAL” 2 3 EARLY SERSYNC MODE SERSYNC PRECEDES MSB “INVERTED” 1 2 1 3 2 LSB WORD0 MSB WORD1 0 15 14 ••• MSB WORD2 2 1 0 DATA SHIFT MSB FIRST 15 14 ••• LSB WORD1 MSB WORD3 2 1 0 15 14 ••• 2 LSB WORD2 FIGURE 33. VALID SERSYNC CONFIGURATION OPTIONS Buffer RAM Output Port The FIFO mode allows the processor to service the interface only when enough samples are present in the RAM. This mode is provided so that the µProcessor does not have to service the PDC every output sample. An interrupt, INTRRPT, is asserted when the desired number of samples are available. The PDC can be programmed to assert the interrupt when up to 7 samples are available. Control Word 21 bit 15 is used to set the Buffer RAM controller to the FIFO mode, while Control Word 21, bits 12-14 set the number of RAM samples to be stored (0 to 7) before the interrupt (INTRRPT) is asserted. Control Word 20 bit 24 determines whether the RAM output interface is the 8-bit microprocessor interface or the 16-bit processor interface. In the 16-bit interface the MSByte is sent to AOUT(7:0) while the LSByte is sent to BOUT(7:0). The Buffer RAM parallel output mode utilizes a RAM to store output data for future retrieval by either the 8-bit microprocessor that is configuring the PDC or by a 16-bit baseband processing engine (which could also be a microprocessor). Data is output from the RAM only on request and can be obtained from either the 8-bit µP interface or from a 16-bit interface that uses the two LSBytes of AOUT and BOUT. The RAM holds up to eight 80-bit sample sets. Each sample set includes 16 bits of each I, Q, magnitude, phase, and frequency data. The RAM samples are mapped as shown in Table 16. The Buffer RAM controller supports both FIFO and Snapshot modes. TABLE 16. RAM DATA STORAGE MAP RAM SAMPLE SET I DATA (000) Q DATA (001) |r| DATA (010) Φ DATA (011) F DATA (100) 0 I0(15:0) Q0(15:0) |r|0(15:0) φ0(15:0) f0(15:0) 1 I1(15:0) Q1(15:0) |r|1(15:0) φ1(15:0) f1(15:0) 2 I2(15:0) Q2(15:0) |r|2(15:0) φ2(15:0) f2(15:0) 3 I3(15:0) Q3(15:0) |r|3(15:0) φ3(15:0) f3(15:0) 4 I4(15:0) Q4(15:0) |r|4(15:0) φ4(15:0) f4(15:0) 5 I5(15:0) Q5(15:0) |r|5(15:0) φ5(15:0) f5(15:0) 6 I6(15:0) Q6(15:0) |r|6(15:0) φ6(15:0) f6(15:0) 7 I7(15:0) Q7(15:0) |r|7(15:0) φ7(15:0) f7(15:0) The INTRRP output signal goes low for 8 PROCCLK cycles when the number of samples in the Buffer RAM (depth) reaches the programmed depth. The depth of the RAM is calculated using Equation 23. A DSP microprocessor or the data processing engine can use the INTRRP signal to know that the RAM is ready to be read. D RAM = [ ( ADDRW RITE – ADDR READ ) – 1 ] MOD8 (EQ. 23) FIFO Operation via 16-Bit µProcessor Interface NOTE: I and Q are sample aligned in time. |r| and φ are sample aligned in time, but one sample delayed from I or Q. The frequency sample is delayed in time from I or Q by 1 sample time + 63 tap FIR impulse response. If the FIR is set to decimate, the FIR output will be repeated every sample time until a new value appears at the filter output. (i.e., the frequency samples are clocked out at the I, Q sample rate regardless of decimation.) Figure 34 shows the conceptual configuration of the 16-bit µProcessor interface. This interface looks like a 16-bit µProcessor read-only microprocessor interface. The SEL(2:0) lines are the address bus and the OEAL and OEBL lines are the read lines. The address is decoded as shown in Table 17. Use of the 16-bit interface for Buffer RAM output requires Control Word 20, bit 25, to be set to a logic “0” and Control Word 20, bit 24, to be set to a logic “1”. Once the Control 31 HSP50214 0 1 2 φ 3 ƒ 4 STATUS 6 MUX DUAL PORT RAM I Q |r| DATA OUTPUT φ ƒ 16 16 16 16 16 DATA INPUT I Q |r| MUX Word 20 has been set to route data to AOUT(7:0) and BOUT(7:0), then the microprocessor must place a value on the PDC input pins SEL(2:0), to choose which data type will be output on AOUT(7:0) and BOUT(7:0). Table 17 defines the data types in terms of SEL(2:0). With the control lines set, the selected data is read MSByte on AOUT(7:0) and LSByte on BOUT(7:0) when OEAL and OEBL (are low). New data only read when OEBL goes low, so use µP for 8bit modes. Programming SEL(2:0) = 110 outputs a 16-bit status signal on AOUT and BOUT. The FIFO status includes FULL, EMPTY, FIFO Depth, and READYB. These status signals are defined in Table 18. TABLE 18. STATUS BIT DEFINITIONS AOUT BIT LOCATION INFORMATION (7:5) FIFO depth - When in FIFO mode, these bits are the current depth of the FIFO. 4 EMPTY - When in FIFO mode, the FIFO is empty, and the read pointer cannot be advanced. Active High. 3 FULL - When in FIFO mode, the FIFO is full, and new samples will not be written. Active High. 2 READYB - When in FIFO mode, the output buffer has reached the programmed threshold. In the snapshot mode, the programmed number of samples have been taken. Active Low. OUTPUT DATA 1-0 GND OEBL WRITE SEQUENCER NEW DATA “SET OF WORDS” ADDRESS SEQUENCER INCR INCR RD WR SEL(2:0) NOTE: In the Status output, BOUT(7:0) are all GND. Figure 35 shows the interface between a 16-bit microprocessor (or other baseband processing engine) and the Buffer RAM output section of the Programmable Down Converter, configured for data output via the parallel outputs AOUT and BOUT. In the 16-bit microprocessor interface configuration, the Buffer RAM pointer is incremented when the µProcessor reads address SEL(2:0) = 7 and OEBL = 0. PROCCLK FIGURE 34. 16-BIT MICROPROCESSOR INTERFACE BUFFER RAM MODE BLOCK DIAGRAM After reset, the FIFO must be incremented to read the first sample set. This is because the RAM read and write pointers cannot point to the same address. Thus, the FIFO pointer must move to the next address before reading the next set of data (I, Q, |r|, φ, and f) samples. 4 PROCCLK cycles are required after an increment before reading can resume. The FIFO write pointer is reset to zero (the first data sample) when Control Word 22 is written to via the 8-bit microprocessor interface. See the Microprocessor Read Section for more detail on how to obtain the Buffer RAM output with this technique. Figure 36 shows the timing diagram required for parallel output operations. In this diagram, only the I, Q and Frequency data are taken from each sample before incrementing to the next sample. Figure 36 assumes that the pointer has already been incremented into a sample. TABLE 17. BUFFER RAM OUTPUT SELECT DEFINITIONS SEL(2:0) OUTPUT DATA TYPE 000 I Data 001 Q Data 010 Magnitude 011 Phase 100 Frequency 101 Unused 110 Memory Status 111 Reading this address increments to the next sample set NOTE: For the very first sample read, the pointer must be incremented first and 4 PROCCLKs must pass before this sample can be read. Figure 36 shows INTRRP going low before the FIFO is read. The FIFO can be read before the number of samples reaches the INTRRP pointer. The number of samples in the FIFO must be monitored by the user via a status read. 32 HSP50214 INTRRP OEAL HSP50214 PDC READ INT 6 RD AOUT(7:0) D(15:8) OEBL 16-BIT µP 7 5 0 4 1 3 2 WRITE D(7:0) BOUT(7:0) FIFO DEPTH A: FIFO DEPTH IS (WRITE - READ) SEL(2:0) A(2:0) WRITE FIGURE 35. INTERFACE BETWEEN A 16-BIT MICROPROCESSOR AND PDC IN FIFO BUFFER RAM MODE 6 8 CLKS INTRRP READ 0 4 1 > 4 CLKS 3 OEAL, OEBL 7 5 2 B: FIFO FULL IS WHEN (WRITE - READ) = 7 SEL(0:2) 0 1 4 AOUT(7:0), BOUT(7:0) I Q FR 1 2 3 4 5 6 7 8 7 0 1 I Q READ 6 1 2 3 4 7 5 WRITE 0 PROCCLK 4 1 3 FIGURE 36. TIMING DIAGRAM FOR PDC IN FIFO MODE WITH OUTPUTS I, Q, AND FREQUENCY SENT TO AOUT(7:0) AND BOUT(7:0) 2 C: FIFO EMPTY IS WHEN (WRITE - READ) = 1 READ Suppose the depth of the Buffer RAM Output section is programmed for an INTRRP pointer depth of 4. If the output is at 4 times the baud rate, the processing routine for the microprocessor may only need to read the buffer when the Buffer RAM had 4 samples since processing is usually on a baud by baud basis. Figure 37 illustrates the conceptual view of the FIFO as a circular buffer, with the Write address one step ahead of the read address. Figure 37A deals with clockwise read and write address incrementing. The FIFO depth is the difference between the Write and Read pointers, modulo 8. Figure 37B illustrates a FIFO status of Full, while Figure 37C illustrates a FIFO empty status condition. Figure 37D illustrates a programmed FIFO depth of 3 and the INTRRP signal indicating that the buffer has sufficient data to be read.Following some simple rules for operating the FIFO will eliminate most operational errors: Rule #1: The Read and Write Pointers cannot point at the same address (the circuitry will not allow this). Rule #2: The FIFO is full when the Write Address = Read Address -1 (no more data will be written until some samples are read or the FIFO is reset). Rule #3: The FIFO is empty when the Read Address = (Write Address -1) (the circuitry will not allow the read pointer to be incremented). 6 WRITE 7 5 0 4 1 3 2 READY D: FIFO READY IS WHEN (WRITE - READ) > DEPTH FIGURE 37. FIFO REGISTER OPERATION Rule #4: You cannot write over what you have not read. Rule #5: RESET places the Write address pointer = 000 and Read address pointer = 111. Rule #6: The best addressing scheme is to read the FIFO until it is empty. This avoids erroneous INTRRP assertions and provides for simple FIFO depth monitoring. The interrupt is generated when the depth increments past the threshold. 33 HSP50214 FIFO Operation via 8-Bit µProcessor Interface Recall that INTRRP stays low for 8 PROCCLK cycles. The FIFO can be read before the INTRRP signal goes low; the number of samples in the FIFO must be monitored by the user. Figure 38 illustrates the timing for RAM load sequence. The Buffer RAM Output may also be accessed via the 8-bit microprocessor interface C(7:0). Figure 39 shows the conceptual configuration of the 8-bit µprocessor interface. Control Word 20 bit 24 must be set to 0 in order to obtain Buffer RAM data to this output. The Microprocessor Read section describes how to read the data from each sample out of the C(7:0) interface. The read pointer of the FIFO is incremented when Control Word 23 is written to. The data can not be read from the next sample until 4 PROCCLKs after the Buffer RAM pointer has been incremented. Control Word 22 is used to reset the Read and Write pointers of the Buffer RAM output to the first sample to 000 and 007 for write and read respectively. PROCCLK I/Q R/φ DELAY TO DATARDY DEPENDS ON LENGTH OF FIR IF FREQ CHOSEN DATARDY (I/Q SELECTED) DATARDY (R/φ SELECTED) INTRPT WRITES TO SNAPSHOT RAM I Q ƒ φ R 4 LSByte 0 R1 R0 A1 “SET OF WORDS” ADDRESS STATUS 1 SEQUENCER R2 1 INCR INCR RD WR MSByte A0 0 MUX 3 R2 R1 R0 A2 A1 A0 SELECTION 0 MUX φ ƒ 0 1 2 MUX I Q |r| MUX WRITE SEQUENCER DUAL PORT RAM DATA OUTPUT φ ƒ 16 16 16 16 16 MUX I Q |r| DATA INPUT FIGURE 38. RAM LOAD SEQUENCE 1 NEW DATA A(2:0) INT(15:0) WRITE ADDRESS “5” R2, R1, R0 A2, A1, A0 0: I;Q 1: |r|; φ 2: ƒ 4: INPUT AGC 5: AGC; TIMING INT(22:16) AGC 0 1 2 MUX CONTROL WORD 23 A2 A1 A0 3 TIMING R0 A1 OUTPUT DATA 0 0 0 0 0 0 RAM I LSB 0 0 0 0 0 1 RAM I MSB 0 0 0 0 1 0 RAM Q LSB 0 0 0 0 1 1 RAM Q MSB 0 0 1 0 0 0 RAM |r| LSB 0 0 1 0 0 1 RAM |r| MSB 0 0 1 0 1 0 RAM φ LSB 0 0 1 0 1 1 RAM φ MSB 0 1 0 0 0 0 RAM ƒ LSB 0 1 0 0 0 1 RAM ƒ MSB 0 1 1 X X X NOT USED 1 0 0 0 0 0 INPUT INTEG LSB 1 0 0 0 0 1 INPUT INTEG NMSB 1 0 0 0 1 0 INPUT INTEG MSB 1 0 1 0 0 0 AGC LSB 1 0 1 0 0 1 AGC MSB 1 0 1 0 1 0 TIMING LSB 1 0 1 0 1 1 TIMING MSB 1 1 X X X X NOT USED X X X 1 1 1 STATUS RD FIGURE 39. 8-BIT MICROPROCESSOR INTERFACE BUFFER RAM MODE BLOCK DIAGRAM 34 HSP50214 Snap Shot Operation WRITE ADDRESS The snapshot mode takes sets of adjacent samples at programmed intervals. It is provided for tracking algorithms that do not require processing of every sample, but do require sets of adjacent samples. For example, bit sync algorithms have narrow loop bandwidths that may not need to be updated every sample. Computing the bit phase may require 4 adjacent samples at 2 times the baud rate. The snapshot mode allows the processor to implement the tracking algorithms for high speed data without having to handle every data sample. INTRRP INTRRP INTRRP RD REEST TIME WR WR WR RD A COMPLETE SET OF 3 DATA SAMPLES IS IN MEMORY AT INTRRP A: NORMAL READ/WRITE SEQUENCE The interval from the start of one snapshot to the start of a second snapshot is programmed into bits 11-4 (where bit 11 is the MSB) of Control Word 21. The actual interval is the value programmed plus 1. If bits 11-4 = 11111111, then the interval is set to 256. If sample sets are to be taken every 4 samples, then bits 11-4 = 00000011. INTRRP INTRRP WRITE ADDRESS INTRRP Figure 40 shows the relationship between the snapshot samples and the snapshot interval. ADJACENT SAMPLES WR WR RD RD TIME WR RD THE THIRD INTERRUPT HAS ONLY 1 NEW DATA ENTRY (INSTEAD OF 3) AT INTRRP B: FALSE TRIGGERED INTERRUPT READ/WRITE SEQUENCE 0 1 2 3 4 62 63 64 65 FIGURE 41. AVOIDING FALSE INTRRP ASSERTIONS # SAMPLES = 4 Microprocessor Write Section INTERVAL = 64 FIGURE 40. SNAP SHOT SAMPLING The microprocessor write section uses an indirect addressing scheme where a 32-bit data word is first loaded in a four 8-bit byte master registers using four writes via C(7:0). The desired destination register address is then written to another address using C(7:0). Writing this address triggers a circuit that generates a pulse, synchronous to clock, that loads the destination register. The sync circuits and data words are synchronized to different clocks, CLKIN or PROCCLK, depending on the destination registers. The PDC begins to fill the buffer each time an interval number of samples have passed. The number of sample sets the PDC writes into the buffer is programmed into bits 3-0 of Control Word 21. The number of samples stored is the programmed value and may be from 1 to 8 sample sets. A sample set consists of I, Q, |r|, φ and ƒ. In snap shot operations, the buffer is read the same as for FIFO operations. Figures 34 and 36 describe the block and timing diagrams required to output data on AOUT(7:0) and BOUT(7:0). Table 17 summarizes the selectable output signals. The method for reading data through the microprocessor section in snap shot mode is identical to the method described in the FIFO mode subsection and the Microprocessor Read Section. A(2:0) determines the destination for the data on bus, C(7:0). Table 19 shows the address map for microprocessor interface. Figure 42 shows the control register loading sequence. The data in C(7:0) and address map in A(2:0) is loaded into the PDC on the rising edge of WR and is latched into the master register on the rising edge of WR and A(2:0) = 100. Four clocks must pass before loading the next control word to guarantee that the data has been transferred. Avoiding Timing Pitfalls When Using the Buffer RAM Output Port Some registers can be loaded (i.e., transferred from the master register to a configuration register or from a holding register to an active register) by initiating a sync. For example, to load the AGC Gain, the value of the AGC gain is first loaded into the holding registers, then a transfer is initiated by SYNCIN2 if Control Word 8, bit 29 = 1. This allows the AGC gain to be loaded by detecting a system event, such as a start of a new burst. Bit 20 of Control Word 0 has the same effect on the Carrier NCO center frequency for assertion of SYNCIN1, except it transfers from a dedicated holding register - not the master register. In snapshot mode, the whole buffer is written whenever the interval counter has timed-out. After time-out, old data can be written over. Thus, the data contained within the buffer must be retrieved before time-out to avoid data loss. It may be desirable to disable the INTRRPT into the controlling microprocessor during read cycles to avoid the generating extra interrupts. Figure 41 details how the WRITE address can trigger extra interrupts Care must be taken to either read sufficient data out of memory or RESET the addressing to ensure that a complete set of data is the cause of the interrupt. 35 HSP50214 Microprocessor Read Section TABLE 19. DEFINITION OF ADDRESS MAP A2-0 REGISTER DESCRIPTION 0 Holding Register 0. Transfers to bits 7-0 of the 32-bit destination register. Bit 0 is the LSB of the 32-bit register. 1 Holding Register 1. Transfers to bits 15-8 of a 32-bit destination register. 2 Holding Register 2. Transfers to bits 23-16 of a 32-bit destination register. 3 Holding Register 3. Transfers to bits 31-24 of a 32-bit destination register. Bit 31 is the MSB of the 32-bit register. 4 This is the destination address register. On the fourth CLK following a write to this register, the contents of the holding registers are transferred to the destination register. All 8 bits written to this register are decoded into the destination register address. The configuration destination address map is given in the tables in the Control Word section. 5 Selects data source for reading. See Microprocessor Read Section. The microprocessor read uses both read and write procedures to obtain data from the PDC. A write must be done to location 5 to select the source of data to be read. The read source is determined by the value placed on the lower three bits of C(7:0). The output from a particular read code is selected using a read address placed on A(2:0). The output is sent to C(7:0) on the falling edge of RD. If the Read Address is equal to 111, the Read Code is ignored, and the status bits shown in Table 22 in the Output Section is sent to C(7:0). This state was provided so that the user could obtain the status bits quickly. Refer to the timing diagram in Figure 43. Suppose the input level detector has a hex value of (321AF5)H, then Table 21 details the steps to be taken. PROCLK WR RD Suppose a (0018D038)H needs to be loaded into control word 0, then Table 20 details the steps to be taken. A2-0 TABLE 20. EXAMPLE PROCESSOR WRITE SEQUENCE STEP A(2:0) C(7:0) COMMENT 1 000 0011 1000 Loads 38 into master register (7:0) on rising edge of WR 2 001 1101 0000 Loads D0 into master register (15:8) on rising edge of WR 010 0001 1000 Loads 18 into master register (23:16) on rising edge of WR 4 011 0000 0000 Loads 00 into master register (31:24) on rising edge of WR 5 100 0000 0000 Load “0018D038” into Configuration Control Register 0 C7-0 1 2 3 OUTPUT DATA C(7:0) LOAD ADDRESS OF TARGET CONTROL REGISTER THREE-STATE INPUT BUS ASSERT RD TO ENABLE DATA OUTPUT ON C0-7 FIGURE 43. READING THE CONTROL REGISTERS USING A LATCH CODE EQUAL TO A 5, A READ ADDRESS AND A READ CODE TABLE 21. PROCESSOR READ SEQUENCE (INPUT LEVEL SETECTOR) Wait 4 CLKS CLK = (PROCCLK, CLKIN) READ ADDRESS READ CODE C(2:0) 3 6 5 STEP A(2:0) C(7:0) COMMENT 1 101 100 Write Read Code, 100 to Address 5, WR pulled high to generate rising edge. 2 000 1111 1000 (F4)H Drop RD low, Read AGC LSB 3 001 0001 1010 (1A)H Pull RD high, then drop low, Read AGC NLSB 4 010 0011 0010 (32)H Pull RD high, then drop low, Read AGC MSB 4 WR A2-0 0 C7-0 LSB 1 2 3 0 4 2 MSB ADD LOAD CONFIGURATION DATA LOAD ADDRESS OF TARGET CONTROL REGISTER AND WAIT 4 CLKs LOAD NEXT CONFIGURATION REGISTER FIGURE 42. LOADING THE CONTROL REGISTERS WITH 32-BIT CONTROL WORDS 36 HSP50214 Applications TABLE 22. DEFINITION OF ADDRESS MAP READ CODE C2-0 STATUS TYPE 0 Buffer RAM I and Q 000- I LSB 001- I MSB 010- Q LSB 011- Q MSB See Output Section. 1 Buffer RAM Output (|r| and φ) 000- MAG LSB (7-0) 001- MAG MSB (15-8) 010- PHASE LSB (7-0) 011- PHASE MSB (15-8) See Output Section. 2 For this example consider a total receive band roughly 25MHz wide containing 124 200kHz wide FDM channels as shown in Figure 44. The design goal for the PDC is to tune to and filter out a single 200kHz FDM channel from the FDM band, passing only baseband samples onto the baseband processor at a multiple of the 270.8 KBPS bit rate. 124 CHANNELS • • • Buffered 000- FREQ LSB Frequency 001- FREQ MSB See Output Section. 3 Not Used 4 Input Level Input AGC Detector 000- input AGC LSB (0-7) 001- input AGC NLSB (8-15) 010- input AGC MSB (16-23) 5 AGC Data AGC (must write to location 10 to sample) and Timing 000- AGC LSB (lower 8 bits of linear Error control word 3 used by multiplier) mmmmmmmm LSB 001- AGC MSB (4 shift control bits and first three bits of linear) control word oeeeemmm MSB. This yields 11 bits of the linear control mantissa. 010- Timing error LSB, Not stabilized. 011- Timing error MSB, Not stabilized. 6 Not Used 7 Not Used Don’t Care Composite Filter Response Example READ ADDRESS A(2:0) Status FREQUENCY 200kHz CHANNEL FREQUENCY FIGURE 44. RECEIVE SIGNAL FREQUENCY SPECTRUM RF/IF Considerations The input frequency to the PDC is dependent on the A/D converter selected, the RF/IF frequency, the bandwidth of interest and the sample rate of the converter. If the A/D converter has sufficient bandwidth, then undersampling techniques can be used to downconvert IF/RF frequencies as part of the digitizing process, using the PDC to process a lower frequency alias of the input signal. 111- Status (6:0) consisting of (6:4)-FIFO depth when output is in FIFO Buffer RAM Output Mode (3)-EMPTY signalling the FIFO is empty and the read pointer cannot be advanced (Active High) (2)-FULL signalling the FIFO is full and new samples will not be written (Active High) (1)-READYB Output buffer has reached the programmed threshold in FIFO mode or the programmed number of samples have been taken in snapshot mode. (Active Low) (0)-INTEGRATION has been completed in the input level detector and is ready to be read. (Active High) For example, a 70MHz IF can be sampled at 40MHz and the resulting 10MHz signal alias can be processed by the PDC to perform the desired downconversion/tuning and filtering. If the IF signal is less than 1/2 the sample frequency then standard oversampling techniques can be used to process the signal. Of the two techniques, only undersampling allows part of the down conversion function to be brought into the digital domain just through sampling, assuming that a sampling frequency can be found that keeps the alias signals low and that the A/D converter has the bandwidth to accept the unconverted analog signal. 37 HSP50214 PDC Configuration References For this example, the PDC is configured as follows: For Intersil documents available on the web, see http://www.Intersil.com/ Intersil AnswerFAX (321) 724-7800. CLKIN: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39MHz Mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gated Input Format: . . . . . . . . . . . . . As required by digital source Carrier NCO Fc: . . . . . . . . . As determined by channel freq. Carrier NCO Phase Offset: . . . . . . . . . . . . . . . . . . . . . . . . . 0 Carrier NCO Offset Frequency: . . . . . . . . . . . . . . . Disabled CIC Filter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enabled Decimation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 PROCCLK: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28MHz Half Band Filters: . . . . . . . . . . . . . . . . . HB3 and 5 Enabled FIR Filter:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . gsmtemp file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . fs = 541.667kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Decimation = 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Passband: 90kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transition Band: 25kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Passband Atten: 3dB . . . . . . . . . . . . . . . . . . . . . . . . . Stop Band Atten: 111.25713 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FIR Order: 90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FIR Symmetry: Even Re-Sampling Filter: . . . . . . . . . . . . . . . . . . . . . HB1 Enabled The basis for this configuration is: [1] HSP50210 Data Sheet, Intersil Corporation, AnswerFAX Doc. No. 3652. [2] Cellular Radio and Personal Communications: A Book of Selected Readings, Theodore S. Rappaport, 1995 by IEEE, Inc. [3] AN9720 Application Note, Intersil Corporation, “Calculating Maximum Processing Rates of the PDC (HSP50214)”, AnswerFAX Doc. No. 99720. Sampling Rate: Select a high rate PROCCLK Output Rate: 1.083MHz (4x Bit Rate; 8x Baud Rate) CIC Filtering: Primarily Rate Reduction (39/18 = 2.166MHz). HB Filtering: Flat passband with rate reduction by 4 - low enough (541.66kHz) for sufficient FIR Taps to be used. FIR Filtering: Primary shaping filter/set final out of band suppression. Polyphase/HalfBand Filtering: Interpolate by two to output 8x baud rate or 4x bit rate. The CIC and halfband filter responses are shown in Figure 45A and B. The composite filter response, constrained primarily by halfband filter 5 and the FIR filter are shown in Figure 46A-C. For a more detailed discussion of design approaches and trades when designing with the PDC, refer to AN9720 [3], “Calculating the Maximum Processing Rates of the PDC”. 38 10 10 -10 -10 -30 -30 MAGNITUDE (dB) MAGNITUDE (dB) HSP50214 -50 -70 -50 -70 -90 -90 -110 -110 fS = CIC INPUT RATE fS = CIC INPUT RATE -130 -130 FREQUENCY fS R FREQUENCY FIGURE 45B. HB3 FILTER RESPONSE 10 -10 -10 -30 -30 MAGNITUDE (dB) 10 -50 -70 -90 fS = CIC INPUT RATE -50 -70 -90 -110 -110 fS = CIC INPUT RATE -130 -130 fS R FREQUENCY FREQUENCY FIGURE 46A. HB5 FILTER RESPONSE FIGURE 46B. 255 FIR TAP FILTER RESPONSE 10 fS = CIC INPUT RATE -10 MAGNITUDE (dB) MAGNITUDE (dB) FIGURE 45A. CIC FILTER RESPONSE fS R -30 -50 -70 -90 -110 -130 FREQUENCY fS R FIGURE 46C. COMPOSITE FILTER RESPONSE FIGURE 46. PDC FILTER FREQUENCY SPECTRUMS EXAMPLE (NORMALIZED TO SAME SCALE) 39 fS R HSP50214 Configuration Control Word Definitions to the master register. Figure 39 details the timing for proper operation of the Microprocessor Write Section. Bits identified as “Reserved” should be programmed to a zero. Note that in the Configuration Control Register tables some of the available 32 bits in a control word are not used. Unused bits do not need to be written to the master register. If the destination only has 16 bits, then only 2 bytes need to be written CONTROL WORD 0: CHIP CONFIGURATION, INPUT SECTION, CIC GAIN (SYNCHRONOUS TO CLKIN) BIT POSITION 31-21 FUNCTION DESCRIPTION Reserved Reserved. 20 Carrier NCO External Sync Enable 0- The SYNCIN1 pin has no effect on the Carrier NCO. 1- When the SYNCIN1 pin is asserted, the carrier center frequency and phase are updated from the holding registers to the active register. Also, if bit 0 of this word is active, the carrier phase accumulator feedback will be zeroed to set the Carrier NCO to a known phase, allowing the NCOs of multiple parts to be initialized and updated synchronously. 19 CIC External Sync Enable 0- The SYNCIN1 pin has no effect on the CIC filter. 1- When the SYNCIN1 pin is asserted, the decimation counter is loaded, allowing the decimation counters in multiple chips to be synchronized. 18 Input Format 0- Two’s Complement Input Format. 1- Offset Binary Input Format. 17 Input Mode 0- Input operates in Gated Mode. 1- Input operates in Interpolated Mode. 16-13 CIC Shift Gain These bits control the barrel shifter at the input to the CIC filter. These bits are added to the GAINADJ(2:0) pins to determine the total shift. The sum is saturated at 15. See the CIC Decimation Filter Section for values to be programmed in this field based on CIC filter Decimation. Bit 16 is the MSB. SG = Floor [39 - (number of input bits) - 5log2(R)] for 4 < R < 31. SG = 15 for R = 4. SG = 0 for R = 32. 12-7 CIC Counter Preload These bits control the decimation in the CIC filter. Program this field to R-1, where R is the desired decimation rate in the filter. The decimation rate range is 4-32. See CIC Filter Section for effective decimation range relative to the CIC Shift Gain value. Bit 12 is the MSB. While this field allows values from 0 - 63, the valid values are in the range from 4- 32. CIC Bypassed Active high, this bit routes the output of the input shifter to the output of the CIC with no filtering. When the CIC filter is bypassed, CLKIN must be at least twice the input sample rate (ENI should be toggled to achieve this). When the CIC filter is bypassed, the bottom 24 bits of the barrel shifter output are routed to the halfband filters. Number of Offset Frequency Bits 00 - 8 bits. 01 - 16. 10 - 24. 11 - 32. 3 Syncout CLK Select This bit selects whether the SYNCOUT signal is generated from CLKIN of from PROCCLK 0- CLKIN. 1- PROCLK. 2 Clear Phase Accum 0- Enable accumulator in Carrier NCO. 1- Zero feedback in accumulator. 1 Carrier NCO Offset Frequency Enable When set to 1, this bit enables the offset frequency word to be added to the center frequency control word. The offset is loaded serially via the COF and COFSYNC pins. 0 Carrier NCO Load Phase Accum On Update When this bit is set to 1, the µP update to the Carrier NCO frequency or an external carrier NCO load using SYNCIN1 will zero the feedback of the phase accumulator as well as update the phase or frequency. This function can be used to set the NCO to a known phase synchronized to an external event. 6 5-4 40 HSP50214 CONTROL WORD 1: INPUT LEVEL DETECTOR (SYNCHRONOUS TO CLKIN) BIT POSITION FUNCTION DESCRIPTION 31 Reserved Reserved. 30 Integration Mode 0- Integration of magnitude error stops when the interval counter times out. 1- Integration runs continuously. When the interval counter times out, the integrator reloads, and the results of the integration is sent to a register for the processor to read. 29-14 Integration Interval These are the top 16 bits of the 18-bit integration counter, ICPrel. ICPrel = (N)/4+1; where N is the desired integration period in CLKIN cycles, defined as the number of input samples to be integrated. N must be a multiple of 4: [0, 4, 8, 12, 16 .... , 218]. Bit 29 is the MSB. If the input is interpolated, then the zeros must be accounted for, as they will be added to the threshold! If the gated input mode is used, the same input sample will be accumulated multiple times. 13-0 Input Threshold Input magnitude threshold. Bits 12-0 correspond to input bits 12-0. The magnitude of the input is added to this threshold, where the threshold is a signed number. Bit 13 is the MSB. CONTROL WORD 2: INPUT LEVEL DETECTOR START STROBE (SYNCHRONIZED TO CLKIN) BIT POSITION N/A FUNCTION Start Input Level Detector AGC Integrator DESCRIPTION Writing to this location starts/restarts the input AGC error integrator. The integrator will either restart or stop when the integration interval counter times out depending on bit 30 of control register 1 (see Microprocessor Write Section). CONTROL WORD 3: CARRIER NCO CENTER FREQUENCY (SYNCHRONIZED TO CLKIN) BIT POSITION 31-0 FUNCTION Carrier Center Frequency DESCRIPTION These bits control the frequency of the Carrier NCO. The frequency range of the NCO is ± FS/2 where FS is the input sample rate. The bits are computed by the equation N = (FNCO / FS)*232. Bit 31 is the MSB. This location is a holding register. After loading, a transfer to the active register is done by writing to Control Word 5 or by generating a SYNCIN1 with Control Word 0 bit 20 set to 1. CONTROL WORD 4: CARRIER PHASE OFFSET (SYNCHRONIZED TO CLKIN) BIT POSITION 31-10 9-0 FUNCTION DESCRIPTION Reserved Reserved Carrier Phase Offset These bits, PO, are used to offset the phase of the carrier NCO. The bits are computed by the equation PO= INT[(210φoff)/ 2π]HEX; (-π <φoff< π) for 10-bit 2’s complement representation or from 0 to 2π for 10-bit offset binary representation. Bit 9 is the MSB. This location is a holding register. After loading, a transfer to the active register is done by writing to Control Word 6 or by generating a SYNCIN1 with Control Word 0 bit 20 set to 1. CONTROL WORD 5: CARRIER FREQUENCY STROBE (SYNCHRONIZED TO CLKIN) BIT POSITION N/A FUNCTION Carrier Frequency Strobe DESCRIPTION Writing to this address updates the carrier frequency control word from the holding register. CONTROL WORD 6: CARRIER PHASE STROBE (SYNCHRONIZED TO CLKIN) BIT POSITION N/A FUNCTION Carrier Phase Strobe DESCRIPTION Writing to this address updates the carrier phase offset control word with the value written to the phase offset (PO) register. 41 HSP50214 CONTROL WORD 7: HB, FIR CONFIGURATION (SYNCHRONIZED TO PROCCLK) BIT POSITION 31-22 FUNCTION DESCRIPTION Reserved Reserved. 21 Enable External Filter Sync 0- The SYNCIN2 pin has no effect on the halfband and FIR filters. 1- When the SYNCIN2 pin is asserted, the filter control circuitry in the halfband filters, the FIR, the resampler, and the discriminator are reset. SYNCIN2 can be used to synchronize the computations of the filters in multiple parts for the alignment. See Synchronization Section. 20 Halfband (HB) Bypass 1- Bypass Halfband Filters. 0- Enable HB Filters (at least one HB must be enabled). 19 HB5 Enable 0- Disables HB number 5 (the last in the cascade). 1- Enables HB filter number 5. 18 HB4 Enable Setting this bit enables HB filter number 4. 17 HB3 Enable Setting this bit enables HB filter number 3. 16 HB2 Enable Setting this bit enables HB filter number 2. 15 HB1 Enable Setting this bit enables HB filter number 1. FIR Decimation Load decimation from 1-16, where 0000 = 16. Bit 14 is the MSB. 10 FIR Real/Complex 0- Complex Filter. 1- Dual Real Filters. 9 FIR Sym Type 0- Odd Symmetry. 1- Even Symmetry. 8 FIR Symmetry 0- Symmetric Filters. 1- Asymmetric Filters. FIR Taps Number of taps in the FIR filter. Range is 1 to 255, where 0000000 is invalid. 14-11 7-0 CONTROL WORD 8: AGC CONFIGURATION 1 (SYNCHRONIZED TO PROCCLK) BIT POSITION 31-30 FUNCTION DESCRIPTION Reserved Reserved. Sync AGC Updates to SYNCIN2 When this bit is 1, the SYNCIN2 pin loads the contents of the master registers into the AGC accumulator. 28-16 Threshold The magnitude measurement out of the cartesian to polar converter is subtracted from this value to get the gain error. A gain of 1.647 in the cartesian to polar conversion that must be taken into account when computing this threshold. These bits are weighted -22 down to 2-10. Bit 28 is the MSB. 15-12 Loop Gain 1 Mantissa Selected when AGCGNSEL = 1. These bits, MMMM, together with the exponent bits, EEEE (11-8), set the loop gain for the AGC loop. The gain adjustment per output sample is: 1.5dB(Threshold -[Magnitude * 1.6]) 0.MMMM * 2-(15 - EEEE) where magnitude ranges from 0 to 1.414 and the threshold is programmed in bits 28-16. The decimal value for the mantissa is calculated as DEC(MMMM)/16. Bit 15 is the MSB. 11-8 Loop Gain 1 Exponent Selected when AGCGNSEL = 1. These bits are EEEE. See description of bits 15-12. Bit 11 is the MSB. 29 42 HSP50214 CONTROL WORD 8: AGC CONFIGURATION 1 (SYNCHRONIZED TO PROCCLK) BIT POSITION FUNCTION DESCRIPTION 7-4 Loop Gain 0 Mantissa Selected when AGCGNSEL = 0. These bits are MMMM. See description for bits 15-12. Same equations are used for Loop 0. Bit 7 is the MSB. 3-0 Loop Gain 0 Exponent Selected when AGCGNSEL = 0. These bits are EEEE. See description for bits 15-12. Same equations are used for Loop 0. Bit 3 is the MSB. CONTROL WORD 9: AGC CONFIGURATION 2 (SYNCHRONIZED TO PROCCLK) BIT POSITION FUNCTION DESCRIPTION 31-28 Reserved Reserved 27-16 Upper Limit Maximum gain/minimum signal. The upper four bits are used for exponent; the remaining bits form the mantissa in the fractional offset binary: [eeeemmmmmmmm]. See the AGC Section for details. Bit 27 is the MSB. The gain is in dB. G = (6.02)(eeee) + 20log10(1.0 + 0.mmmmmmmm) eeee = Floor [log2(10GAIN dB/20)]. mmmmmmmm = Floor [512(10GAIN dB/20/2eeee - 1)]. 15-12 Reserved Reserved. 11-0 Lower Limit Minimum gain/maximum signal. The upper four bits are used for exponent; the remaining bits form the mantissa in the fractional offset binary: [eeeemmmmmmmm]. See the AGC Section for details. Bit 11 is the MSB. The gain is in dB. G = (6.02)(eeee) + 20log10(1.0 + 0.mmmmmmmm). eeee = Floor [log2(10GAIN dB/20)]. mmmmmmmm = Floor [512(10GAIN dB/20/2eeee - 1)]. CONTROL WORD 10: AGC SAMPLE GAIN CONTROL STROBE (SYNCHRONIZED TO PROCCLK) BIT POSITION N/A FUNCTION Sample AGC Gain Level DESCRIPTION Writing to this location samples the output of the AGC loop filter to stabilize the value for µP reading. CONTROL WORD 11: TIMING NCO CONFIGURATION (SYNCHRONIZED TO PROCCLK) BIT POSITION 31-6 FUNCTION DESCRIPTION Reserved Reserved. 5 Enable External Timing NCO Sync 0- SYNCIN2 has no effect on the timing NCO. 1- When SYNCIN2 is asserted, the timing NCO center frequency and phase are updated with the value loaded in their holding registers. If bit 0 of this word is set to 1, the phase accumulator feedback is also zeroed. 4-3 Number of Offset Frequency Bits 00 - 8 bits. 01 - 16. 10 - 24. 11 - 32. Enable Offset Frequency 0- Zero Offset Frequency to Adder. 1- Enable Offset Frequency. 2 43 HSP50214 CONTROL WORD 11: TIMING NCO CONFIGURATION (SYNCHRONIZED TO PROCCLK) BIT POSITION FUNCTION DESCRIPTION 1 Clear Phase Accumulator 0- Enable Accumulator. 1- Zero Feedback in Accumulator. 0 Timing NCO Phase Accumulator Load On Update When this bit is set to 1, the µP update to the timing NCO frequency or an external timing NCO load using SYNCIN2 will zero the feedback of the phase accumulator as well as update the phase and frequency. This function can be used to set the NCO to a known phase synchronized to an external event. CONTROL WORD 12: TIMING NCO CENTER FREQUENCY (SYNCHRONIZED TO PROCCLK) BIT POSITION 31-0 FUNCTION DESCRIPTION Timing NCO Center Frequency These bits control the frequency of the timing NCO. The frequency range of the NCO is from 0 to FRESAMP where FRESAMP is the input sample rate to the re-sampling filter. The bits are computed by the equation: N =(fOUT /FRESAMP)*232. Bit 31 is the MSB. This location is a holding register. After loading, a transfer to the active register is done by writing to Control Word 14 or by generating a SYNCIN2 with Control Word 11 bit 5 set to 1. CONTROL WORD 13: TIMING PHASE OFFSET (SYNCHRONIZED TO PROCCLK) BIT POSITION FUNCTION DESCRIPTION 31-8 Reserved Reserved. 7-0 Timing NCO Phase Offset These bits are used to offset the phase of the carrier NCO. The range is 0 to 1 times the resampler input period interpreted either as ± T/2 (2’s complement) or 0 to T (offset binary). Bit 7 is the MSB. This location is a holding register. After loading, a transfer to the active register is done by writing to Control Word 15 or by generating a SYNCIN2 with Control Word 11 bit 5 set to 1. CONTROL WORD 14: TIMING FREQUENCY STROBE (SYNCHRONIZED TO PROCCLK) BIT POSITION N/A FUNCTION Timing Frequency Strobe DESCRIPTION Writing to this address updates the active timing NCO frequency register in the timing NCO (see Timing NCO Section). CONTROL WORD 15: TIMING PHASE STROBE (SYNCHRONIZED TO PROCCLK) BIT POSITION FUNCTION DESCRIPTION N/A Timing Phase Strobe Writing to this address updates the active timing NCO phase offset register in the timing NCO (see Timing NCO Section). 44 HSP50214 CONTROL WORD 16: RE-SAMPLING FILTER CONTROL (SYNCHRONIZED TO PROCCLK) BIT POSITION FUNCTION 31-12 Reserved 11-4 Resampler Output Pulse Delay DESCRIPTION Reserved. NOTE: These bits program the delay between output samples when interpolating. The extra outputs can be delayed from 2 to 255 clocks from the first output. A delay of 2 equals 255 clocks of delay. A delay of 0 or 1 is an invalid mode. When interpolating by 2, one extra output is generated; when interpolating by 4, 3 extra outputs are generated. Program by the equation (PROCCLK/fOUT) - 1. Bit 11 is the MSB. NOTE: If less than 5 is programmed, there will not be sufficient time to fully update the output buffer. If less than 16 is programmed, the serial output may be preempted. This means that it won’t finish and if the sync is programmed to follow the data, there may never be a sync. 3 Resampler Bypass 0- Re-Sampling Filter Enabled. A valid combination of bits 2-0 must also be selected. 1- Re-Sampling Filter is Bypassed. 2-0 Filter Mode Select; 2- HB2 Enabled 1- HB1 Enabled 0- Resampler Enabled 000- Not Valid. 001- Resampler Enabled. 010- Halfband 1 Enabled. 011- Resampler and Halfband Filter 1 Enabled. 100- Not Valid. 101- Not Valid. 110- Both Halfband Filters Enabled. 111- Resampler and Both Halfband Filters Enabled. CONTROL WORD 17: DISCRIMINATOR FILTER CONTROL, DISCRIMINATOR DELAY (SYNCHRONIZED TO PROCCLK) BIT POSITION FUNCTION DESCRIPTION 31-17 Reserved Reserved. 16-15 Phase Multiplier These bits program allow the phase output of the cartesian to polar converter to be multiplied by 1, 2, 4, or 8 (modulo 2π) to remove phase modulation before the frequency is measured. 00- No Shift on Phase Input to frequency discriminator. 01- Shift Phase Input to frequency discriminator up 1 (one bit), discarding the MSB and zero filling the LSB. 10- Shift Phase Input to frequency discriminator up 2 (two) bits, discarding the MSB and zero filling the LSB. 11- Shift Phase Input to frequency discriminator up 3 (three) bits, discarding the MSB and zero filling the LSB. Discriminator Enable 0- Disable Discriminator. 1- Enable Discriminator. Discriminator FIR Decimation The decimation can be programmed from 1 to 8, where 000 = decimate by 8; 001 = decimate by 1; 010 = decimate by 2; 011 = decimate by 3; 100 = decimate by 4; 101 = decimate by 5; 110 = decimate by 6; and 111 - decimate by 7. 10 FIR Symmetry Type 0- Odd Symmetry. 1- Even Symmetry. 9 FIR Symmetry 0- Symmetric. 1- Asymmetric. 8-3 Number of FIR Taps Number of FIR taps from 1 to 63, where 00000 is not valid (00001 = 1 tap, 00010 = 2 taps, etc. up to 11111 = 63 taps). Bit 8 is the MSB. 2-0 Discriminator Delay Sets the number of delays from 1 to 8 in the discriminator. Set delay ddd to delay minus 1, where 000 represents 1 delay; 001 represents 2 delays, 010 represents 3 delays, 011 represents 4 delays, 100 represents 5 delays, 101 represents 6 delays, 110 represents 7 delays, and 111 represents 8 delays. If ddd the decimal representation bits 2-0, then the discriminator a transfer function H(Z) = 1-Z-(ddd + 1). 14 13-11 45 HSP50214 CONTROL WORD 18: TIMING ERROR PRELOADS (SYNCHRONIZED TO PROCCLK) BIT POSITION FUNCTION DESCRIPTION 31-28 Reserved Reserved. 27-16 NCO Divide The Resampler NCO output is divided down by the value loaded into this register plus 1. Load with a value that is one less than the desired period. Bit 27 is the MSB. 11-0 Reference Divide The reference clock is divided down by the value loaded into this register plus 1. Load with a value that is one less than the desired period. Bit 27 is the MSB. A minimum preload of “I” is required. CONTROL WORD 19: SERIAL OUTPUT ORDER (SYNCHRONIZED TO PROCCLK) BIT POSITION 31 FUNCTION DESCRIPTION Reserved Reserved. 30-28 Data Source for SEROUTA Serial Output A source. The serial data source is selected using Table 12 (see Output Section). 27-25 Data Source for SEROUTB Serial Output B source. The serial data source is selected using Table 12 (see Output Section). 24-21 Number of Serial Word Links in a Chain This parameter determines the number of SERSYNC pulses generated. It can be set from 1 to 7. If this parameter matches the number of serial words that are linked together to form a serial output chain, then there will be a sync pulse for every word in the serial output. In applications where a processor is receiving the serial data, it may be desirable to have a single SERSYNC pulse for the whole serial output chain, instead of a SERSYNC for each word in the data chain. The processor then parses out the various data words. As an example, if the I and Q are chained together and a single SERSYNC pulse is generated for this serial output chain, no ambiguity exists in the processor about which two data samples (one from I and one from Q) are related. 20-18 Link Following I Data The serial data word, or link, following the I data word is selected using Table 12 (see Output Section). 17-15 Link Following Q Data The serial data word, or link, following the Q data word is selected using Table 12 (see Output Section). 14-12 Link Following Magnitude Data The serial data word, or link, following the MAG data word is selected using Table 12 (see Output Section). 11-9 Link Following Phase Data The serial data word, or link, following the PHAS data word is selected using Table 12 (see Output Section). 8-6 Link Following Frequency Data The serial data word, or link, following the FREQ data word is selected using Table 12 (see Output Section). 5-3 Link Following AGC Level Data The serial data word, or link, following the AGC data word is selected using Table 12 (see Output Section). 2-0 Link Following Timing Error Data The serial data word, or link, following the TIMERR data word is selected using Table 12 (see Output Section). 46 HSP50214 CONTROL WORD 20: BUFFER RAM, DIRECT PARALLEL, AND DIRECT SERIAL OUTPUT CONFIGURATION (SYNCHRONIZED WITH PROCCLK) BIT POSITION 31-26 FUNCTION DESCRIPTION Reserved Reserved. 25 Data Source for Least Significant Bytes of AOUT and BOUT Output LSBytes, bits (7:0), of AOUT and BOUT can provide: 0- Buffer RAM Mode Output or. 1- Parallel Direct Mode Output. 24 Buffered Output Mode Interface Buffered Mode Output interfaces to either: 0- 8-bit µP (address = µP ASEL(5:#); CLK = µP RAM read). 1- 16-bit µP (address = SEL(2:0); CLK = OEBL). 23-22 AOUT Direct Parallel Output Mode Data Source The data word sent by the Direct Parallel Output Mode to AOUT is: 00- I Data. 01- Magnitude. 1X- Frequency. 21-20 BOUT Direct Parallel Output Mode Data Source The data word sent by the Direct Parallel Output Mode to BOUT is: 00- Q Data. 01- Phase. 1X- Magnitude. 19 Serial Output Sync Polarity 0- Normal Sync Mode (active high). 1- Sync Inverted (active low). 18 Serial Output Clock Polarity 0- Output Clock Inverted rising edge aligns with data transitions. 1- Output Clock Normal falling edge aligns with data transitions. 0 17 1 Serial Output Sync Position 0- Sync is asserted one bit time after the last bit of the serial word (Late Mode). 1- Sync is asserted one bit time prior to the first bit of the serial word (Early Mode). 16-14 Serial Out Clock Divider 000- Serial Output at PROCCLK/16. 001- Serial Output at PROCCLK/8. 010- Serial Output at PROCCLK/4. 011- Serial Output at PROCCLK/2. 1XX- Serial Output at PROCCLK rate. 13-12 I Data Serial Output Tag Bit 00- No Tag Bit. LSB of word is passed. 01- 0 Tag Bit. LSB of word is set to zero. 1X- 1 Tag Bit. LSB of word is set to one. 11-10 Q Data Serial Output Tag Bit (See I Data Serial Output Tag Selection above). 9-8 Magnitude Data Serial Output Tag Bit (See I Data Serial Output Tag Selection above). 7-6 Phase Data Serial Output Tag Bit (See I Data Serial Output Tag Selection above). 5-4 Frequency Data Serial Output Tag Bit (See I Data Serial Output Tag Selection above). 3-2 AGC Data Serial Output Tag Bit (See I Data Serial Output Tag Selection above). 47 HSP50214 CONTROL WORD 20: BUFFER RAM, DIRECT PARALLEL, AND DIRECT SERIAL OUTPUT CONFIGURATION (SYNCHRONIZED WITH PROCCLK) (Continued) BIT POSITION 1-0 FUNCTION Timing Error Data Serial Output Tag Bit DESCRIPTION (See I Data Serial Output Tag Selection above). CONTROL WORD 21: BUFFER RAM OUTPUT CONTROL REGISTER (SYNCHRONIZED TO PROCCLK) BIT POSITION 31-16 FUNCTION DESCRIPTION Reserved Reserved. Output Buffer Mode 0- The output buffer operates in snapshot mode. 1- The output buffer operates in FIFO mode. 14-12 FIFO Mode Depth Threshold In FIFO mode, when the FIFO depth reaches this threshold, an interrupt is generated and the READY flag is asserted. The threshold may be set from 0 to 7. Bit 14 is the MSB. The interrupt is generated when the FIFO depth reaches the threshold, as the FIFO fills. 11-4 Snapshot Mode Interval In snapshot mode, the interval between snapshots in the output sample times is determined by this 8-bit binary number, i.e. 256, (28), sample time counts between snapshot samples. Program this parameter to 1 less than the desired interval. Bit 11 is the MSB. 3-0 Snapshot Mode Number of Samples In snapshot mode, the number of samples stored each time the snapshot interval counter times out is equal to the decimal version of this 4-bit number. The range is 1- 8. Bit 3 is the MSB. 15 CONTROL WORD 22: BUFFER RAM OUTPUT FIFO RESET (SYNCHRONIZED TO PROCCLK) BIT POSITION N/A FUNCTION FIFO reset DESCRIPTION A write to this address increments the output FIFO RAM address pointers to READ = 111 and WRITE = 000. CONTROL WORD 23: INCREMENT OUTPUT FIFO (SYNCHRONIZED TO PROCCLK) BIT POSITION N/A FUNCTION FIFO Strobe DESCRIPTION A write to this address increments the output FIFO/buffer to the next sample set. CONTROL WORD 24: SYNCOUT STROBE OUTPUT PIN (SYNCHRONIZED TO CLKIN OR PROCCLK DEPENDING ON PROGRAMMING IN CONTROL WORD 0) BIT POSITION N/A FUNCTION SYNCOUT Strobe DESCRIPTION A write to this address generates a one clock period wide strobe on the SYNCOUT pin that is synchronized to the clock. This strobe may be synchronized to CLKIN or PROCCLK based on the programming of bit 3 of Control Word 0. 48 HSP50214 CONTROL WORD 25: COUNTER AND ACCUMULATOR RESET (SYNCHRONIZED TO BOTH CLKIN AND PROCCLK) BIT POSITION N/A FUNCTION Counter and Accumulator Reset DESCRIPTION A write to this address initializes the counters and accumulators for testing. Items that are reset are: Carrier NCO 1. Loads phase offset <9:0> into register to be used for adding to accumulator. 2. Enables feedback on the accumulator. CIC Filter 1. 2. 3. 4. Resets the decimation counter. Clears enables to CIC. Clears accumulators in CIC. Clears enable leaving CIC. Halfband Filters 1. 2. 3. 4. 5. Resets compute counter in Halfband control. Resets read address for all Halfband Filters. Resets write address for all Halfband Filters. Clears input available strobe. Resets Halfband control logic. 255 Tap FIR 1. Resets FIR read and write address pointers. 2. Zero’s coefficient read address. AGC Loop 1. Clears accumulator in loop filter. Resampler and Interpolation Halfband Filters. 1. Resets counters for Halfband addresses for writing. 2. Resets output enable. 3. Reset controller for Resampler. Timing NCO 1. Initializes counters for inserting extra pulses when interpolating halfbands are enabled. Discriminator 1. Resets read and write address pointers. 2. Zero’s coefficient read address. Cartesian to Polar Coordinate Counter. 1. Resets Cordic counters (stops current computation). FIFO Control 1. 2. 3. 4. 5. 6. Resets decoder for controlling FIFO. Resets write address for FIFO. Clears RD and INTRRPT. Resets “depth” and “full” flags. Sets the empty flag. Sets the read address to “7”, write address to “0”. Snapshot Control 1. Zeros the group number. 2. Load interval counter. 3. Resets write address and read address for FIFO. Output Serial Control 1. 2. 3. 4. Reloads shift counter. Reloads “Number of Words” counter. Reloads counter for sync (for early or late). Reloads counter for dividing down SERCLK. 49 HSP50214 CONTROL WORD 26: LOAD AGC GAIN (SYNCHRONIZED TO PROCCLK) BIT POSITION N/A FUNCTION AGC Load DESCRIPTION Writing to this location generates a strobe to load the AGC loop accumulator with bits (15:5) to the master registers. These bits are loaded into the MSBs of the AGC loop filter accumulator with bits (15:12) mapping to the shift (exponent) control bits and bits (11:5) mapping to the multiplier (mantissa) bits. Bits (11:5) represent a binary mantissa mapped to the linear gain as: 01.XXXXXXX. See AGC Section. CONTROL WORD 27: TEST REGISTER (SYNCHRONIZED TO CLKIN) BIT POSITION 31-0 FUNCTION Reserved DESCRIPTION A fixed value 0000 0010 0111 1000 [0278]HEX is loaded here for normal operation. A fixed value 0000 0010 0111 1010 [027A]HEX is loaded here for setting the Sin/Cos generator outputs to 7FFF. CONTROL WORDS 64-95: DISCRIMINATOR COEFFICIENT REGISTERS (SYNCHRONIZED TO PROCCLK) BIT POSITION 31-10 FUNCTION Discriminator FIR Coefficient DESCRIPTION The discriminator FIR coefficients are 22-bit-two’s complement. If the filter is symmetric, the coefficients are loaded from the center coefficient at address 64 to the last coefficient. If the filter is asymmetric the coefficients C0 to CN are loaded with C0 in address 64 up to 64+N, where N is number of asymmetric coefficients. CONTROL WORDS 128-255: 255 PROGRAMMABLE COEFFICIENT REGISTERS BIT POSITION 31-10 FUNCTION Programmable FIR Coefficient DESCRIPTION The programmable FIR coefficients are 22-bit-two’s complement. If the filter is symmetric, the coefficients are loaded from the center coefficient at address 128 to the last coefficient. If the filter is asymmetric the coefficients C0 to CN are loaded with C0 in address 128 up to 128+N, where N is number of asymmetric coefficients. Real Filters are computed as: Xn-k+1 Ck1 + Xn-k+2 Ck-2 + ... XnC0). where C0 is the coefficient in address 128 and Xo is the oldest data sample. Complex filters outputs are computed as follows: Xn is the most recent data sample. k is the number of samples = number of (complex) taps. C0_re is the coefficient loaded into CW128. C0_im is the coefficient loaded into CW129. The convolution starts with the oldest data, times the last complex coefficient, and ends with the newest data, times the first complex coefficient loaded. Iout = (-Xn-k+1_q * Ck-1_im + Xn-k+1_i * Ck-1_re). + (-Xn-k+2_q * Ck-2_im + Xn-1+2_i * Ck-2_re). + ... + (-Xn_q * C0_im + Xn_i * C0_re). Qout = (Xn-k+1_i * Ck-1_im + Xn-k+1_q * Ck-1_re). + (Xn-k+2_i * Ck-2_im + Xn-1+2_q * Ck-2_re). + ... + (Xn_i * C0_im + Xn_q * C0_re). 50 HSP50214 Absolute Maximum Ratings Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V Input, Output or I/O Voltage . . . . . . . . . . . . GND-0.5V to VCC +0.5V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 2 Thermal Resistance (Typical, Note 1) θJA (oC/W) MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (Lead Tips Only) Operating Conditions Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.75V to +5.25V Temperature Range Commercial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +0.8V Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2V to VCC Input Rise and Fall Time. . . . . . . . . . . . . . . . . . . . . . . . . . 1V/ns Max CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 5. θJA is measured with the component mounted on an evaluation PC board in free air. DC Electrical Specifications PARAMETER VCC = 5 ±5%, TA = 0oC to 70oC, Commercial; -40oC to 85oC, Industrial MIN MAX UNITS Logical One Input Voltage SYMBOL VIH VCC = 5.25V 2.0 - V Logical Zero Input Voltage VIL VCC = 4.75V - 0.8 V Clock Input High VIHC VCC = 5.25V 3.0 - V Clock Input Low VILC VCC = 4.75V - 0.8 V Output High Voltage VOH IOH = -400µA, VCC = 4.75V 2.6 - V Output Low Voltage VOL IOL = +2.0mA, VCC = 4.75V - 0.4 V -10 10 µA Input Leakage Current II Standby Power Supply Current ICCSB Output Leakage Current IO Operating Power Supply Current ICCOP Input Capacitance CIN Output Capacitance COUT TEST CONDITIONS VIN = VCC or GND, VCC = 5.25V - 500 µA -10 10 µA f = 52MHz, VIN = VCC or GND, VCC = 5.25V, Outputs Not Loaded - 364 mA (Note 2) Freq = 1MHz, VCC open, all measurements are referenced to device ground - 10 pF (Note 3) VCC = 5.25V, Outputs Not Loaded VIN = VCC or GND, VCC = 5.25V NOTES: 6. Power Supply current is proportional to operation frequency. Typical rating for ICCOP is 6mA/MHz. 7. Capacitance TA = 25oC, controlled via design or process parameters and not directly tested. Characterized upon initial design and at major process or design changes. AC Electrical Specifications VCC = 5 ±5%, TA = 0o to 70oC, Commercial; -40oC to 85oC, Industrial 52MHz PARAMETER SYMBOL MIN MAX UNITS CLKIN Clock Period tCP 19 - ns CLKIN High tCH 7 - ns CLKIN Low tCL 7 - ns PROCCLK Period tPCP 28.5 - ns PROCCLK High tPCH 7 - ns PROCCLK Low tPCL 7 - ns REFCLK Clock Frequency fRCP - PROCCLK/2 ns REFCLK High tRCH 7 - ns 51 HSP50214 AC Electrical Specifications VCC = 5 ±5%, TA = 0o to 70oC, Commercial; -40oC to 85oC, Industrial (Continued) 52MHz PARAMETER SYMBOL MIN MAX UNITS REFCLK Low tRCL 7 - ns Setup Time GAINADJ(2:0), IN(13:0), ENI, COF, COFSYNC, and SYNCIN1 to CLKIN tDS 7 - ns Hold Time GAINADJ(2:0), IN(13:0), ENI, COF, COFSYNC, and SYNCIN1 to CLKIN tDH 0 - ns Setup Time AGCGNSEL, SOF, MCSYNCI, SOFSYNC, and SYNCIN2 to PROCCLK tDSS 7 - ns Hold Time AGCGNSEL, SOF, MCSYNCI, SOFSYNC, and SYNCIN2 to PROCCLK tDHS 0 - ns Setup Time A(2:0), C(7:0) to Rising Edges of WR tWS 8 - ns Hold Time A(2:0), C(7:0) to Rising Edges of WR tWH 3 - ns WR to CLKIN tWC 15 - ns (Note 6) PROCCLK to AOUT(15:0), BOUT(15:0), DATARDY, SEROUTA, SEROUTB, SERSYNC, INTRRP, MCSYNCO SYNCOUT Valid tDO - 10 ns PROCCLK to SERCLK Valid tDOS - 15 ns WR High tWRH 15 - ns WR Low tWRL 10 - ns RD Low tRL 25 - ns Address Setup to Read Low tAS - 3 ns RD LOW to Data Valid tRDO - 24 ns RD HIGH to Output Disable tROD - 10 ns (Note 5) Output Enable Time tOE - 8 ns Output Disable Time tOD - 8 ns (Note 5) Output Rise, Fall Time tRF - 3 ns (Note 5) NOTES: 8. AC tests performed with CL = 40pF, IOL = 2mA, and IOH = -400µA. Input reference level for CLK is 2.0V, all other inputs 1.5V. Test VIH = 3.0V, VIHC = 4.0V, VIL = 0V. 9. Controlled via design or process parameters and not directly tested. Characterized upon initial design and at major process or design changes. 10. Setup time required to ensure action initiated by WR will be seen by a particular CLKIN. AC Test Load Circuit DUT S1 CL (NOTE) SWITCH S1 OPEN FOR ICCSB AND ICCOP IOH ± 1.5V EQUIVALENT CIRCUIT NOTE: Test head capacitance. 52 IOL HSP50214 Waveforms tRL RD tWRL tAS tWRH A(2-0) WR tWS tWH C(0-7) C(0-7), A(0-2) tROD tRDO FIGURE 47. TIMING RELATIVE TO WR FIGURE 48. TIMING RELATIVE TO RD tCP tCL tCH CLKIN tDS tRF tDH IN(13:0), COF GAINADJ(2:0), ENI, COFSYNC, SYNCIN1 tRF 2.0V 0.8V WR tWC FIGURE 49. OUTPUT RISE AND FALL TIMES FIGURE 50. TIMING RELATIVE TO CLKIN tPCP tPCL tPCH PROCCLK tDSS tDHS AGCGNSEL, MCSYNC1 SOF, SOFSYNC, SYNCIN2 OEAH, OEAL, OEBH, OEBL tOE OUTA(15:8), OUTA(7:0), OUTB(15:8), OUTB(7:0) AOUT(15:0), BOUT(15:0), DATARDY, INTRRP, MCSYNC0, SYNCOUT, SEROUTA, SEROUTB, SERSYNC 1.5V 1.5V tOD 1.7V tDO SERCLK 1.3V tDOS FIGURE 51. OUTPUT ENABLE/DISABLE FIGURE 52. TIMING RELATIVE TO PROCCLK tRCP fRCP = I tRCP tRCP = 2 tRCP tRCH tRCL FIGURE 53. REFCLK 53 HSP50214 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 54 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029