HT6010/HT6012/HT6014 312 Series of Encoders Features · Operating voltage: 2.4V~12V · Built-in oscillator needs only 5% resistor · Low power and high noise immunity CMOS · Easy interface with an RF or an infrared transmission technology medium · Low standby current · Minimal external components · Minimum transmission word · Pair with Holtek¢s 312 series of decoders - Four words for TE trigger - One word for Data trigger · 18-pin DIP, 20-pin SOP package Applications · Burglar alarm system · Car alarm system · Smoke and fire alarm system · Security system · Garage door controllers · Cordless telephones · Car door controllers · Other remote control systems General Description The 312 encoders are a series of CMOS LSIs for remote control system applications. They are capable of encoding 12 bits of information which consists of N address bits and 12-N data bits. Each address/data input is externally trinary programmable if bonded out. They are otherwise set floating internally. Various packages of the 312 encoders offer flexible combinations of pro- grammable address/data which meet various applications. The programmable address/data is transmitted together with the header bits via an RF or an infrared transmission medium upon receipt of a trigger signal. A TE (HT6010) or a DATA (HT6012/HT6014) trigger can be selected for application flexibility. Selection Table Function Address No. Part No. Address/ Data No. Data No. Oscillator Trigger LED Indicator Package HT6010 8 4 0 RC oscillator TE No 18DIP, 20SOP HT6012 10 0 2 RC oscillator D10~D11 Yes 18DIP, 20SOP HT6014 8 0 4 RC oscillator D8~D11 Yes 18DIP, 20SOP Note: Address/Data represents pins that can be either address or data according to the application requirement. Rev. 1.20 1 September 9, 2003 HT6010/HT6012/HT6014 Block Diagram TE Trigger HT6010 O S C 2 O S C 1 O s c illa to r ¸ 3 D iv id e r T E A 0 A 7 1 2 T r a n s m is s io n G a te C ir c u it A D 8 ¸ 1 2 C o u n te r a n d 1 o f 1 2 D e c o d e rs D a ta S e le c t a n d B u ffe r D O U T S y n c . C ir c u it T r in a r y D e te c to r A D 1 1 V D D V S S DATA Trigger HT6012/HT6014 O S C 2 O S C 1 O s c illa to r A d d re s s 1 2 T r a n s m is s io n G a te C ir c u it ¸ 3 D iv id e r ¸ 1 2 C o u n te r a n d 1 o f 1 2 D e c o d e rs T r in a r y D e te c to r D a ta Note: D a ta S e le c t a n d B u ffe r D O U T S y n c . C ir c u it L E D C ir c u it V D D V S S L E D The address/data pins are available in various combinations (refer to the address/data table). Rev. 1.20 2 September 9, 2003 HT6010/HT6012/HT6014 Pin Assignment T E T r ig g e r T y p e 8 -A d d re s s 4 -A d d r e s s /D a ta 8 -A d d re s s 4 -A d d r e s s /D a ta N C 1 2 0 N C A 0 1 1 8 V D D A 0 2 1 9 V D D A 1 2 1 7 D O U T A 1 3 1 8 D O U T A 2 3 1 6 O S C 2 A 2 4 1 7 O S C 2 A 3 4 1 5 O S C 1 A 3 5 1 6 O S C 1 A 4 5 1 4 T E A 4 6 1 5 T E A 5 6 1 3 A D 1 1 A 5 7 1 4 A D 1 1 A 6 7 1 2 A D 1 0 A 6 8 1 3 A D 1 0 A 7 8 1 1 A D 9 A 7 9 1 2 A D 9 V S S 9 1 0 A D 8 V S S 1 0 1 1 A D 8 H T 6 0 1 0 1 8 D IP -A D A T A H T 6 0 1 0 2 0 S O P -A T r ig g e r T y p e 1 0 -A d d re s s 2 -D a ta 1 0 -A d d re s s 2 -D a ta 8 -A d d re s s 4 -D a ta N C 1 2 0 A 0 1 1 8 V D D A 0 2 1 9 V D D A 0 1 1 8 V D D A 1 2 1 7 D O U T A 1 3 1 8 D O U T A 1 2 1 7 D O U T A 2 3 1 6 O S C 2 A 2 4 1 7 O S C 2 A 2 3 1 6 O S C 2 A 3 4 1 5 O S C 1 A 3 5 1 6 O S C 1 A 3 4 1 5 O S C 1 A 4 5 1 4 L E D A 4 6 1 5 L E D A 4 5 1 4 L E D A 5 6 1 3 D 1 1 A 5 7 1 4 D 1 1 A 5 6 1 3 D 1 1 A 6 7 1 2 D 1 0 A 6 8 1 3 D 1 0 A 6 7 1 2 D 1 0 A 7 8 1 1 A 9 A 7 9 1 2 A 9 A 7 8 1 1 D 9 V S S 9 1 0 A 8 V S S 1 0 1 1 A 8 V S S 9 1 0 D 8 H T 6 0 1 2 2 0 S O P -A H T 6 0 1 2 1 8 D IP -A N C H T 6 0 1 4 1 8 D IP -A 8 -A d d re s s 4 -D a ta N C 1 2 0 A 0 2 1 9 V D D A 1 3 1 8 D O U T A 2 4 1 7 O S C 2 A 3 5 1 6 O S C 1 A 4 6 1 5 L E D A 5 7 1 4 D 1 1 A 6 8 1 3 D 1 0 A 7 9 1 2 D 9 1 0 1 1 D 8 V S S N C H T 6 0 1 4 2 0 S O P -A Rev. 1.20 3 September 9, 2003 HT6010/HT6012/HT6014 Pin Description Pin Name I/O Internal Connection Description A0~A9 I TRANSMISSION Input pins for address A0~A9 setting GATE They can be externally set to VDD or VSS or left open. AD8~AD11 I TRANSMISSION Input pins for address/data (AD8~AD11) setting GATE They can be externally set to VDD or VSS or left open. D8~D11 I CMOS IN Pull-high Input pins for data (D8~D11) setting and transmission enable (active low) They can be externally set to VSS or left open (see Note). DOUT O CMOS OUT Encoder data serial transmission output LED O NMOS OUT Transmission enable indicator, active low TE I CMOS IN Pull-high OSC1 I OSCILLATOR Oscillator input pin OSC2 O OSCILLATOR Oscillator output pin VSS ¾ ¾ Negative power supply, ground VDD ¾ ¾ Positive power supply Note: Transmission enable, active low (see Note) D8~D11 are data input and transmission enable pins of the HT6012/HT6014. TE is the transmission enable pin of the HT6010. Approximate Internal Connections T R A N S M IS S IO N G A T E C M O S IN P u ll- h ig h C M O S O U T N M O S O U T O S C IL L A T O R E N O S C 1 O S C 2 Absolute Maximum Ratings Supply Voltage ............................VSS-0.3V to VSS+13V Storage Temperature ............................-50°C to 125°C Input Voltage ................................VSS-0.3 to VDD+0.3V Operating Temperature...........................-20°C to 75°C Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Rev. 1.20 4 September 9, 2003 HT6010/HT6012/HT6014 Electrical Characteristics Symbol Parameter VDD Operating Voltage ISTB Standby Current Ta=25°C Test Conditions Min. Typ. Max. Unit 2.4 5 12 V ¾ 0.1 1 mA ¾ 2 4 mA ¾ 250 500 mA 12V ¾ 600 1200 mA 5V VLED=0.5V 1.5 3 ¾ mA 5V VOH=0.9VDD (Source) -0.6 -1.2 ¾ mA 5V VOL=0.1VDD (Sink) 0.6 1.2 ¾ mA VDD Conditions ¾ ¾ 3V Oscillator stops 12V IDD 3V Operating Current ILED LED Sink Current IDOUT Output Drive Current No load, fOSC=3kHz VIH ²H² Input Voltage ¾ ¾ 0.8VDD ¾ VDD V VIL ²L² Input Voltage ¾ ¾ 0 ¾ 0.2VDD V fOSC Oscillator Frequency 5V ROSC=1MW ¾ 3 ¾ kHz RTE TE Pull-high Resistance 5V ¾ 1.5 3 MW RDATA D8~D11 Pull-high Resistance 5V VDATA=0V ¾ 1.5 3 MW VTE=0V Functional Description Operation The 312 series of encoders begin with a four (HT6010) or a one (HT6012/HT6014) word transmission cycle upon receipt of a transmission enable (TE for the HT6010 or D8~D11 for the HT6012/HT6014, active low). This cycle will repeat itself as long as the transmission enable (TE or D8~D11) is held low. Once the transmission enable returns high the encoder output completes its final cycle and then stops as shown below. T E o r D 8 ~ D 1 1 < 1 w o rd E n c o d e r D a ta O u t T r a n s m itte d C o n tin u o u s ly 1 o r 4 w o rd s 1 o r 4 w o rd s Transmission Timing Information Word An information word is composed of four periods as shown: 1 /6 b it s y n c . p e r io d p ilo t p e r io d ( 6 b its ) a d d r e s s c o d e p e r io d d a ta c o d e p e r io d Composition of Information Rev. 1.20 5 September 9, 2003 HT6010/HT6012/HT6014 Address/Data Waveform Each programmable address/data pin can be externally set to one of the following three logic states: fO S C "O n e " "Z e ro " "O p e n " A d d r e s s /D a ta B it Address/Data Bit Waveform The ²Open² state data input is interpreted as logic high by the decoder since its output has only two states. Address/Data Programming (Preset) The status of each address/data pin can be individually preset to a logic ²high², ²low², or ²floating². If a transmission enable signal is applied, the encoder scans and transmits the status of the 12 bits of address/data serially in the order A0 to AD11 for the HT6010 and A0 to D11 for the HT6012/HT6014. If the trigger signal is not applied, the chip only consumes a standby current which is less than 1mA (for VDD=5V). The address pins are usually preset so as to transmit data codes with their own particular security codes by the DIP switches or PCB wiring, while data is selected using push button or electronic switches. Address/Data Sequence The following table provides the position of the address/data sequence for various models of the 312 series encoders. Address/Data Bits Part No. 0 1 2 3 4 5 6 7 8 9 10 11 HT6010 A0 A1 A2 A3 A4 A5 A6 A7 AD8 AD9 AD10 AD11 HT6012 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 D10 D11 HT6014 A0 A1 A2 A3 A4 A5 A6 A7 D8 D9 D10 D11 Transmission Enable For the TE trigger type of encoders, transmission is enabled by applying a low signal to the TE pin. But for the Data trigger type, it is enabled by applying a low signal to one of the data pins D8~D11. Rev. 1.20 6 September 9, 2003 HT6010/HT6012/HT6014 Flowchart P o w e r o n S ta n d b y m o d e N o T r a n s m is s io n e n a b le d ? Y e s C o d e w o rd tr a n s m itte d c o n tin u o u s ly N o T r a n s m is s io n s till e n a b le d ? Y e s C o d e w o rd tr a n s m itte d c o n tin u o u s ly Note: D8~D11 are transmission enable of the HT6012/HT6014. TE is the transmission enable of the HT6010. Oscillator Frequency vs. Supply Voltage fO S C (S c a le ) R (W ) O S C 7 .0 0 4 7 0 k 5 1 0 k 6 .0 0 5 6 0 k 6 2 0 k 5 .0 0 6 8 0 k 7 5 0 k 4 .0 0 8 2 0 k 9 1 0 k 1 .0 M (3 k H z )3 .0 0 1 .2 M 1 .5 M 2 .0 0 2 .0 M 1 .0 0 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 V D D (V D C ) The recommended oscillator frequency is fOSCD (decoder) @ 33 fOSCE (encoder) Rev. 1.20 7 September 9, 2003 HT6010/HT6012/HT6014 Application Circuits T r a n s m itte r C ir c u it T r a n s m itte r C ir c u it V 1 V D D 1 8 1 A 0 V D D 1 8 A 1 D O U T 1 7 2 A 1 D O U T 1 7 A 2 O S C 2 1 6 3 A 2 O S C 2 1 6 4 A 3 O S C 1 1 5 A 0 2 3 V D D R O S C 4 A 3 O S C 1 1 5 5 A 4 T E 1 4 5 A 4 L E D 6 1 4 A D 1 1 1 3 6 A 5 D 1 1 1 3 A 6 A D 1 0 1 2 7 A 6 D 1 0 1 2 8 A 7 A D 9 1 1 8 A 7 A 9 1 1 V S S A D 8 1 0 9 V S S A 8 1 0 9 A 5 7 H T 6 0 1 0 R D D O S C R H T 6 0 1 2 T r a n s m itte r C ir c u it V 1 A 0 V D D 1 8 2 A 1 D O U T 1 7 3 A 2 O S C 2 1 6 4 A 3 O S C 1 1 5 5 A 4 L E D 6 A 5 D 1 1 1 3 7 A 6 D 1 0 1 2 8 A 7 D 9 1 1 9 V S S D 8 1 0 1 4 R D D O S C R H T 6 0 1 4 Rev. 1.20 8 September 9, 2003 HT6010/HT6012/HT6014 Package Information 18-pin DIP (300mil) Outline Dimensions A B 1 8 1 0 1 9 H C D E a G I F Symbol A Rev. 1.20 Dimensions in mil Min. Nom. Max. 895 ¾ 915 B 240 ¾ 260 C 125 ¾ 135 D 125 ¾ 145 E 16 ¾ 20 F 50 ¾ 70 G ¾ 100 ¾ H 295 ¾ 315 I 335 ¾ 375 a 0° ¾ 15° 9 September 9, 2003 HT6010/HT6012/HT6014 20-pin SOP (300mil) Outline Dimensions 1 1 2 0 A B 1 1 0 C C ' G H D E Symbol Rev. 1.20 a F Dimensions in mil Min. Nom. Max. A 394 ¾ 419 B 290 ¾ 300 C 14 ¾ 20 C¢ 490 ¾ 510 D 92 ¾ 104 E ¾ 50 ¾ F 4 ¾ ¾ G 32 ¾ 38 H 4 ¾ 12 a 0° ¾ 10° 10 September 9, 2003 HT6010/HT6012/HT6014 Product Tape and Reel Specifications Reel Dimensions D T 2 A C B T 1 SOP 20W Symbol Description Dimensions in mm A Reel Outer Diameter 330±1.0 B Reel Inner Diameter 62±1.5 C Spindle Hole Diameter 13.0+0.5 -0.2 D Key Slit Width 2.0±0.5 T1 Space Between Flange 24.8+0.3 -0.2 T2 Reel Thickness 30.2±0.2 Rev. 1.20 11 September 9, 2003 HT6010/HT6012/HT6014 Carrier Tape Dimensions P 0 D P 1 t E F W C D 1 B 0 P K 0 A 0 SOP 20W Symbol Description Dimensions in mm W Carrier Tape Width 24.0+0.3 -0.1 P Cavity Pitch 12.0±0.1 E Perforation Position 1.75±0.1 F Cavity to Perforation (Width Direction) 11.5±0.1 D Perforation Diameter 1.5+0.1 D1 Cavity Hole Diameter 1.5+0.25 P0 Perforation Pitch 4.0±0.1 P1 Cavity to Perforation (Length Direction) 2.0±0.1 A0 Cavity Length 10.8±0.1 B0 Cavity Width 13.3±0.1 K0 Cavity Depth 3.2±0.1 t Carrier Tape Thickness 0.3±0.05 C Cover Tape Width Rev. 1.20 21.3 12 September 9, 2003 HT6010/HT6012/HT6014 Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shanghai Sales Office) 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233 Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor Inc. (Shenzhen Sales Office) 5/F, Unit A, Productivity Building, Cross of Science M 3rd Road and Gaoxin M 2nd Road, Science Park, Nanshan District, Shenzhen, China 518057 Tel: 0755-8616-9908, 8616-9308 Fax: 0755-8616-9533 Holtek Semiconductor Inc. (Beijing Sales Office) Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031 Tel: 010-6641-0030, 6641-7751, 6641-7752 Fax: 010-6641-0125 Holtek Semiconductor Inc. (Chengdu Sales Office) 709, Building 3, Champagne Plaza, No.97 Dongda Street, Chengdu, Sichuan, China 610016 Tel: 028-6653-6590 Fax: 028-6653-6591 Holmate Semiconductor, Inc. (North America Sales Office) 46729 Fremont Blvd., Fremont, CA 94538 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright Ó 2003 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.20 13 September 9, 2003