HT82V739 1200mW Audio Power Amp with Shutdown Features · Operating voltage: 2.2V to 5.5V · Wide temperature operating range · High signal-to-noise ratio · Low power-on and chip enable or disable POP noise. · Low distortion · Low standby current · Large output voltage swing · Power off control · Low power consumption · Direct drive speaker · Output power 1200mW at 10% THD+N into 8W · 8-pin DIP/SOP package (VDD=5V) Applications · Applied for HT36 series, HT86 series and other Holtek products General Description HT82V739 is an integrated class AB mono speaker driver contained in a 8-pin DIP/SOP package. The HT82V739 is capable of delivering 1200mW output power to an 8W load with less than 10% (THD+N) from a 5V power supply. The very low standby current in shutdown mode contributes to the reduction of power consumption of battery-powered equipments. Block Diagram Pin Assignment O U T N A u d In O U T P 1 0 R R R A M P 2 A M P 1 V R E F B IA S 1 8 V D D 2 7 O U T P V R E F 3 6 N C V S S 4 5 C E H T 8 2 V 7 3 9 8 D IP -A /S O P -A R V S S V D D O U T N A u d In C E Pin Description Pin No. Pin Name 1 OUTN 2 3 I/O Description O Negative output Aud In I Audio input VREF O Speaker non-inverting input voltage reference 4 VSS ¾ 5 CE I 6 NC ¾ Not connected 7 OUTP O Positive output 8 VDD ¾ Positive power supply Rev. 1.20 Negative power supply, ground Chip enable, low active 1 January 17, 2008 HT82V739 Absolute Maximum Ratings Supply Voltage ...........................VSS-0.3V to VSS+6.0V Storage Temperature ............................-50°C to 125°C Input Voltage..............................VSS-0.3V to VDD+0.3V Operating Temperature...........................-40°C to 85°C Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Electrical Characteristics Symbol Parameter VSS=0V, Ta=25°C Test Conditions Min. Typ. Max. Unit 2.2 5.0 5.5 V ¾ 2.2 4.0 mA 5V ¾ 3.5 6.0 mA ¾ ¾ 1 mA VDD Conditions ¾ D.C. Characteristics VDD Supply Voltage ¾ IDD Quiescent Power Supply Current 3V VIN=0VP-P, No load ISD Shutdown Power Supply Current 5V VIN=0VP-P, CE=VDD, No load VIH Input High Voltage for CE ¾ ¾ 0.7VDD ¾ VDD V VIL Input Low Voltage for CE ¾ ¾ 0 ¾ 0.3VDD V RL=4W 198 330 ¾ RL=8W 180 300 ¾ RL=16W 144 240 ¾ RL=4W 270 450 ¾ RL=8W 240 400 ¾ RL=16W 168 280 ¾ RL=4W 690 1150 ¾ RL=8W 570 950 ¾ RL=16W 390 650 ¾ RL=4W 840 1400 ¾ RL=8W 720 1200 ¾ RL=16W 480 800 ¾ ¾ 145 ¾ ms ¾ 105 ¾ ms ¾ 0.3 ¾ % ¾ 0.18 ¾ % ¾ 0.13 ¾ % RL=4W ¾ 66 ¾ dB RL=8W ¾ 70 ¾ dB RL=16W ¾ 72 ¾ dB (THD+N)/S£1%, VIN=1kHz sinewave 3V (THD+N)/S£10%, VIN=1kHz sinewave PO Output Power (THD+N)/S£1%, VIN=1kHz sinewave 5V (THD+N)/S£10%, VIN=1kHz sinewave mW mW A.C. Characteristics tON Enable Time 3V V =1kHz sinewave, IN 5V No load RL=4W Power output=500mW, Total Harmonic Distortion Plus (THD+N)/S 5V RL=8W VIN=1kHz sinewave Noise-to-signal Ratio RL=16W S/N Rev. 1.20 Signal to Noise Ratio VIN=1Vrms 1kHz 5V sinewave 2 January 17, 2008 HT82V739 Functional Description OUTP Rising Time (tR) When CE is active low, the HT82V739 needs rising time to output fully on OUTP pin. However, the rising time depends on C1. (*see the application circuits) C E O U T P tR Capacitor tR 0.1mF 1mF 4.7mF 10mF 2.2V 15ms 30ms 90ms 185ms 3V 15ms 30ms 90ms 185ms 4V 15ms 30ms 90ms 185ms Voltage For battery based applications, power consumption is a key issue, therefore the amplifier should be turned off when in the standby state. In order to eliminate any speaker sound bursts while turning the amplifier on, the application circuit, which will incorporate a capacitance value of C1, should be adjusted in accordance with the speaker¢s audio frequency response. A greater value of C1 will improve the noise burst while turning on the amplifier. The recommended operation sequence is: Turn On: ²Aud In² signal standby (1/2 VDD) ® enable amplifier ® wait tR for amplifier ready ® ²Aud In² signal start Turn Off: ²Aud In² signal finish ® disable amplifier ® wait tR for amplifier off ® ²Aud In² signal off A u d In tR tR C E O U T If the application is not powered by batteries and there is no problem with amplifier On/Off issue, a capacitor value of 0.1mF for C1 is recommended. Rev. 1.20 3 January 17, 2008 HT82V739 THD+N VS. Output Power · RLOAD=4W, VIN=1kHz sinewave % T H D + N v s O u tp u t P o w e r 1 0 0 5 0 2 0 1 0 5 2 1 0 .5 0 .2 0 .1 0 .0 5 0 .0 2 0 .0 1 1 m 2 m 5 m 1 0 m 2 0 m 5 0 m 1 0 0 m 2 0 0 m 5 0 0 m 1 2 5 O u tp u t P o w e r (W ) · RLOAD=8W, VIN=1kHz sinewave % T H D + N v s O u tp u t P o w e r 1 0 0 5 0 2 0 1 0 5 2 1 0 .5 0 .2 0 .1 0 .0 5 0 .0 2 0 .0 1 1 m 2 m 5 m 1 0 m 2 0 m 5 0 m 1 0 0 m 2 0 0 m 5 0 0 m 1 2 5 O u tp u t P o w e r (W ) · RLOAD=16W, VIN=1kHz sinewave % T H D + N v s O u tp u t P o w e r 1 0 0 5 0 2 0 1 0 5 2 1 0 .5 0 .2 0 .1 0 .0 5 0 .0 2 0 .0 1 1 m 2 m 5 m 1 0 m 2 0 m 5 0 m 1 0 0 m 2 0 0 m 5 0 0 m 1 2 5 O u tp u t P o w e r (W ) Rev. 1.20 4 January 17, 2008 HT82V739 Application Circuits A u d io In 1 C 3 1 m F R 2 3 O U T P Rev. 1.20 5 6 7 5 D D 8 H T 8 2 V 7 3 9 V R E F N C C E V D D C E C 1 1 m F A u d In V O U T N C 2 4 7 m F S P K 4 January 17, 2008 HT82V739 Package Information 8-pin DIP (300mil) Outline Dimensions A 8 B 5 4 1 H C D a G E I F Symbol A Rev. 1.20 Dimensions in mil Min. Nom. Max. 355 ¾ 375 B 240 ¾ 260 C 125 ¾ 135 D 125 ¾ 145 E 16 ¾ 20 70 F 50 ¾ G ¾ 100 ¾ H 295 ¾ 315 I 335 ¾ 375 a 0° ¾ 15° 6 January 17, 2008 HT82V739 8-pin SOP (150mil) Outline Dimensions 5 8 A B 4 1 C C ' G H D E Symbol Rev. 1.20 a F Dimensions in mil Min. Nom. Max. A 228 ¾ 244 B 149 ¾ 157 C 14 ¾ 20 C¢ 189 ¾ 197 D 53 ¾ 69 E ¾ 50 ¾ F 4 ¾ 10 G 22 ¾ 28 H 4 ¾ 12 a 0° ¾ 10° 7 January 17, 2008 HT82V739 Product Tape and Reel Specifications Reel Dimensions D T 2 A C B T 1 SOP 8N Symbol Description A Reel Outer Diameter B Reel Inner Diameter Dimensions in mm 330±1.0 62±1.5 13.0+0.5 -0.2 C Spindle Hole Diameter D Key Slit Width 2.0±0.15 T1 Space Between Flange 12.8+0.3 -0.2 T2 Reel Thickness 18.2±0.2 Rev. 1.20 8 January 17, 2008 HT82V739 Carrier Tape Dimensions P 0 D P 1 t E F W C D 1 B 0 P K 0 A 0 SOP 8N Symbol Description Dimensions in mm W Carrier Tape Width 12.0+0.3 -0.1 P Cavity Pitch 8.0±0.1 E Perforation Position 1.75±0.1 F Cavity to Perforation (Width Direction) 5.5±0.1 D Perforation Diameter 1.55±0.1 D1 Cavity Hole Diameter 1.5+0.25 P0 Perforation Pitch 4.0±0.1 P1 Cavity to Perforation (Length Direction) 2.0±0.1 A0 Cavity Length 6.4±0.1 B0 Cavity Width 5.20±0.1 K0 Cavity Depth 2.1±0.1 t Carrier Tape Thickness 0.3±0.05 C Cover Tape Width Rev. 1.20 9.3 9 January 17, 2008 HT82V739 Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shanghai Sales Office) 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233 Tel: 86-21-6485-5560 Fax: 86-21-6485-0313 http://www.holtek.com.cn Holtek Semiconductor Inc. (Shenzhen Sales Office) 5/F, Unit A, Productivity Building, Cross of Science M 3rd Road and Gaoxin M 2nd Road, Science Park, Nanshan District, Shenzhen, China 518057 Tel: 86-755-8616-9908, 86-755-8616-9308 Fax: 86-755-8616-9722 Holtek Semiconductor Inc. (Beijing Sales Office) Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031 Tel: 86-10-6641-0030, 86-10-6641-7751, 86-10-6641-7752 Fax: 86-10-6641-0125 Holtek Semiconductor Inc. (Chengdu Sales Office) 709, Building 3, Champagne Plaza, No.97 Dongda Street, Chengdu, Sichuan, China 610016 Tel: 86-28-6653-6590 Fax: 86-28-6653-6591 Holtek Semiconductor (USA), Inc. (North America Sales Office) 46729 Fremont Blvd., Fremont, CA 94538 Tel: 1-510-252-9880 Fax: 1-510-252-9885 http://www.holtek.com Copyright Ó 2008 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.20 10 January 17, 2008