184pin Unbuffered DDR SDRAM DIMMs based on 512Mb B ver.
This Hynix unbuffered Dual In-Line Memory Module (DIMM) series consists of 512Mb B ver. DDR SDRAMs in 400mil
TSOP II packages on a 184pin glass-epoxy substrate. This Hynix 512Mb B ver. based unbuffered DIMM series provide
a high performance 8 byte interface in 5.25" width form factor of industry standard. It is suitable for easy interchange
and addition.
FEATURES
•
JEDEC Standard 184-pin dual in-line memory module
(DIMM)
•
Programmable Burst Length 2 / 4 / 8 with both
sequential and interleave mode
•
Two ranks 128M x 72, 128M x 64 and One rank 64M
x 72, 64M x 64, 32M x 64 organization
•
Edge-aligned DQS with data outs and Center-aligned
DQS with data inputs
•
2.6V ± 0.1V VDD and VDDQ Power supply for
DDR400, 2.5V ± 0.2V for DDR333 and below
•
Auto refresh and self refresh supported
•
8192 refresh cycles / 64ms
•
All inputs and outputs are compatible with SSTL_2
interface
•
Serial Presence Detect (SPD) with EEPROM
•
Fully differential clock operations (CK & /CK) with
133/166/200MHz
•
Built with 512Mb DDR SDRAMs in 400 mil TSOP II
packages
•
DLL aligns DQ and DQS transition with CK transition
•
Lead-free product listed for each configuration
(RoHS compliant)
•
Programmable CAS Latency: DDR266(2, 2.5 clock),
DDR333(2.5 clock), DDR400(3 clock)
ADDRESS TABLE
Organization
Ranks
SDRAMs
# of
DRAMs
# of row/bank/column Address
Refresh
Method
256MB
32M x 64
1
32Mb x 16
4
13(A0~A12)/2(BA0,BA1)/10(A0~A9)
8K / 64ms
512MB
64M x 64
1
64Mb x 8
8
13(A0~A12)/2(BA0,BA1)/11(A0~A9,A11)
8K / 64ms
512MB
64M x 72
1
64Mb x 8
9
13(A0~A12)/2(BA0,BA1)/11(A0~A9,A11)
8K / 64ms
1GB
128M x 64
2
128Mb x 8
16
13(A0~A12)/2(BA0,BA1)/11(A0~A9,A11)
8K / 64ms
1GB
128M x 72
2
128Mb x 8
18
13(A0~A12)/2(BA0,BA1)/11(A0~A9,A11)
8K / 64ms
PERFORMANCE RANGE
Part-Number Suffix
-D431
-J
-H
Unit
Speed Bin
DDR400B
DDR333
DDR266B
-
CL - tRCD- tRP
3-3-3
2.5-3-3
2.5-3-3
CK
CL=3
200
-
-
MHz
CL=2.5
166
166
133
MHz
CL=2
133
133
133
MHz
Max Clock
Frequency
Note:
1. 2.6V ± 0.1V VDD and VDDQ Power supply for DDR400 and 2.5V ± 0.2V for DDR333 and below
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev. 1.1 / May. 2005
1
1184pin Unbufferd DDR SDRAM DIMMs
ORDERING INFORMATION
Part Number
Density Organization
# of
DRAMs
Material
DIMM Dimension
ECC
Support
HYMD532646B6-H
256MB
32Mb x 16
4
Normal
133.35 x 31.75 x 3.18 [mm3]
None
HYMD532646BP6-H
256MB
32Mb x 16
4
Lead-free1
↑
None
HYMD532646B6J-D43/J
256MB
32Mb x 16
4
Normal
↑
None
HYMD532646BP6J-D43/J
256MB
32Mb x 16
4
Lead-free1
↑
None
HYMD564646B8-H
512MB
64Mb x 8
8
Normal
↑
None
HYMD564646BP8-H
512MB
64Mb x 8
8
Lead-free1
↑
None
HYMD564646B8J-D43/J
512MB
64Mb x 8
8
Normal
↑
None
↑
None
1
HYMD564646BP8J-D43/J
512MB
64Mb x 8
8
Lead-free
HYMD564726B8-H
512MB
64Mb x 8
9
Normal
↑
ECC
HYMD564726BP8-H
512MB
64Mb x 8
9
Lead-free1
↑
ECC
HYMD564726B8J-D43/J
512MB
64Mb x 8
9
Normal
↑
ECC
↑
ECC
HYMD564726BP8J-D43/J
1
512MB
64Mb x 8
9
Lead-free
HYMD512646B8-H
1GB
128Mb x 8
16
Normal
133.35 x 31.75 x 4 [mm3]
None
HYMD512646BP8-H
1GB
128Mb x 8
16
Lead-free1
↑
None
HYMD512646B8J-D43/J
1GB
128Mb x 8
16
Normal
↑
None
HYMD512646BP8J-D43/J
1GB
128Mb x 8
16
Lead-free1
↑
None
HYMD512726B8-H
1GB
128Mb x 8
18
Normal
↑
ECC
↑
ECC
1
HYMD512726BP8-H
1GB
128Mb x 8
18
Lead-free
HYMD512726B8J-D43/J
1GB
128Mb x 8
18
Normal
↑
ECC
HYMD512726BP8J-D43/J
1GB
128Mb x 8
18
Lead-free1
↑
ECC
Note:
1. The “Lead-free” products contain Lead less than 0.1% by weight and satisfy RoHS - please contact Hynix for product availability.
* These products are built with HY5DU124(8,16)22BT[P], the Hynix DDR SDRAM component.
Rev. 1.1 / May. 2005
2
1184pin Unbufferd DDR SDRAM DIMMs
PIN DESCRIPTION
Pin
CK0~2, /CK0~2
/CS0, /CS1
CKE0, CKE1
/RAS, /CAS, /WE
A0 ~ A13
A10/AP
BA0, BA1
DQ0~DQ63
CB0~CB7
DQS0~DQS8
DM0~8
Pin Description
Pin
Differential Clock Inputs
Chip Select Inputs
Clock Enable Inputs
Commend Sets Inputs
Address Inputs
Address Input/Autoprecharge
Bank Address
Data Inputs/Outputs
Data Check bits
Data Strobes
Data-in Masks
Pin Description
VDD
VDDQ
VSS
VREF
VDDSPD
VDDID
SA0~SA2
SCL
SDA
DU
NC
TEST
Power Supply for Core and I/O
Power Supply for DQs
Ground
Input/Output Reference
Power Supply for SPD
VDD, VDDQ Level Detection
SPD Address Inputs
SPD Clock Input
SPD Data Input/Output
Do not Use
No Connect
Reserved for test equipment use
PIN ASSIGNMENT
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Name
VREF
DQ0
VSS
DQ1
DQS0
DQ2
VDD
DQ3
NC
NC
VSS
DQ8
DQ9
DQS1
VDDQ
CK1
/CK1
VSS
DQ10
DQ11
CKE0
VDDQ
DQ16
DQ17
DQS2
VSS
A9
DQ18
A7
VDDQ
DQ19
Pin
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Name
A5
DQ24
VSS
DQ25
DQS3
A4
VDD
DQ26
DQ27
A2
VSS
A1
CB0,NC
CB1,NC
VDD
NC,DQS8
A0
CB2,NC
VSS
CB3,NC
BA1
Key
DQ32
VDDQ
DQ33
DQS4
DQ34
VSS
BA0
DQ35
DQ40
Pin
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
Name
VDDQ
/WE
DQ41
/CAS
VSS
DQS5
DQ42
DQ43
VDD
NC,/CS2
DQ48
DQ49
VSS
/CK2
CK2
VDDQ
DQS6
DQ50
DQ51
VSS
VDDID
DQ56
DQ57
VDD
DQS7
DQ58
DQ59
VSS
NC
SDA
SCL
Pin
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
Name
VSS
DQ4
DQ5
VDDQ
DM0,DQS9
DQ6
DQ7
VSS
NC
NC,TEST
NC,FETEN
VDDQ
DQ12
DQ13
DM1,DQS10
VDD
DQ14
DQ15
CKE1
VDDQ
BA2
DQ20
A12
VSS
DQ21
A11
DM2,DQS11
VDD
DQ22
A8
DQ23
Pin
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
Name
VSS
A6
DQ28
DQ29
VDDQ
DM3,DQS12
A3
DQ30
VSS
DQ31
CB4,NC
CB5,NC
VDDQ
CK0
/CK0
VSS
DM8,DQS17
A10
CB6,NC
VDDQ
CB7,NC
Key
VSS
DQ36
DQ37
VDD
DM4,DQS13
DQ38
DQ39
VSS
DQ44
Pin
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
Name
/RAS
DQ45
VDDQ
/CS0
/CS1
DM5,DQS14
VSS
DQ46
DQ47
NC,/CS3
VDDQ
DQ52
DQ53
NC,A13
VDD
DM6
DQ54
DQ55
VDDQ
NC
DQ60
DQ61
VSS
DM7,DQS16
DQ62
DQ63
VDDQ
SA0
SA1
SA2
VDDSPD
note:
1. Pins 44, 45, 47, 49, 51, 134, 135, 140, 142, 144 are reserved for x72 variants of this module and are not used on the x64 versions.
2. Pins 111, 158 are not used for single rank module.
3. Pin 167 is “NC” for 256MB, 512MB and 1GB or “A13” for 2GB module.
4. Pins 9, 10, 71, 82, 90, 101, 102, 103, 113, 163, 167, 173 are not used on this module.
Rev. 1.1 / May. 2005
3
1184pin Unbufferd DDR SDRAM DIMMs
FUNCTIONAL BLOCK DIAGRAM
256MB, 32M x 64 Unbuffered DIMM: HYMD532646B[P]6[J]
/CS0
DQS1
DM1/DQS10
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQS0
DM0/DQS9
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
LDQS
LDM
I/O0
I/O1
I/O2
I/O3
I/O4
I/O5
I/O6
I/O7
UDQS
UDM
I/O8
I/O9
I/O10
I/O11
I/O12
I/O13
I/O14
I/O15
/CS
LDQS
LDM
I/O0
I/O1
I/O2
I/O3
I/O4
I/O5
I/O6
I/O7
UDQS
UDM
I/O8
I/O9
I/O10
I/O11
I/O12
I/O13
I/O14
/CS
DQS3
DM3/DQS12
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DQS2
DM2/DQS11
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQS5
DM5/DQS14
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQS4
DM4/DQS13
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D0
DQS7
DM7/DQS16
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D1
DQS6
DM6/DQS15
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
I/O15
DQ23
SCL
W
P A0
SDA
A1 A2
SA0 SA1 SA2
*Clock Wiring
Clock Input
SDRAMs
*CK0, /CK0
*CK1, /CK1
*CK2, /CK2
NC
2 SDRAMs
2 SDRAMs
*Wire per Clock Loading
Table/Wiring Diagrams
/CS
LDQS
LDM
I/O0
I/O1
I/O2
I/O3
I/O4
I/O5
I/O6
I/O7
UDQS
UDM
I/O8
I/O9
I/O10
I/O11
I/O12
I/O13
I/O14
/CS
D2
D3
I/O15
DQ55
Serial PD
LDQS
LDM
I/O0
I/O1
I/O2
I/O3
I/O4
I/O5
I/O6
I/O7
UDQS
UDM
I/O8
I/O9
I/O10
I/O11
I/O12
I/O13
I/O14
I/O15
VDD SPD
SPD
VDD /VDDQ
DO-D3
VREF
DO-D3
VSS
DO-D3
VDDID
Strap:see Note 4
BA0-BA1
A0-A13
/RAS
/CAS
CKE0
/WE
Rev. 1.1 / May. 2005
BA0-BA1 : SDRAMs D0-D3
A0-A13 : SDRAMs D0-D3
/RAS : SDRAMs D0-D3
/CAS : SDRAMs D0-D3
CKE : SDRAMs D0-D3
/WE : SDRAMs D0-D3
Notes :
1. DQ-to-I/O wiring is shown as recommended but may be changed.
2. DQ/DQS/DM/CKE/S relationships must be maintained as shown.
3. DQ, DQS, DM/DQS resistors : 22 Ohms +- 5%.
4. VDDID strap connections
(for memory device VDD, VDDQ):
STRAP OUT (OPEN) : VDD = VDDQ
STRAP IN (VSS) : VDD ≠ V DDQ
5. BAx, Ax, RAS, CAS, WE resistors : 7.5 Ohms +- 5%
4
1184pin Unbufferd DDR SDRAM DIMMs
FUNCTIONAL BLOCK DIAGRAM
512MB, 64M x 64 Unbuffered DIMM: HYMD564646B[P]8[J]
/CS0
DQS0
DM0/DQS9
DQS4
DM4/DQS13
DM
I/O7
I/O6
I/O1
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
I/O0
I/O5
/CS
DQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D0
I/O4
I/O3
I/O2
DQS1
DM1/DQS10
/CS
DQS
D4
I/O0
I/O5
I/O4
I/O3
I/O2
DQS5
DM5/DQS14
DM
I/O7
I/O6
I/O1
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
I/O0
I/O5
/CS
DQS
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D1
I/O4
I/O3
I/O2
DQS2
DM2/DQS11
DM
I/O7
I/O6
I/O1
/CS
DQS
D5
I/O0
I/O5
I/O4
I/O3
I/O2
DQS6
DM6/DQS15
DM
I/O7
I/O6
I/O1
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
I/O0
I/O5
/CS
DQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D2
I/O4
I/O3
I/O2
DQS3
DM3/DQS12
DM
I/O7
I/O6
I/O1
/CS
DQS
D6
I/O0
I/O5
I/O4
I/O3
I/O2
DQS7
DM7/DQS16
DM
I/O7
I/O6
I/O1
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
I/O0
I/O5
/CS
DQS
I/O4
I/O3
I/O2
VDD SPD
SDA
W
P
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D3
Serial PD
SCL
DM
I/O7
I/O6
I/O1
SPD
VDD /VDDQ
DO-D8
VREF
A0
A1
A2
SA0 SA1 SA2
DO-D8
DO-D8
VSS
VDDID
Strap:see Note 4
DM
I/O7
I/O6
I/O1
/CS
DQS
D7
I/O0
I/O5
I/O4
I/O3
I/O2
*Clock Wiring
Clock Input
SDRAMs
*CK0, /CK0
*CK1, /CK1
*CK2, /CK2
2 SDRAMs
3 SDRAMs
3 SDRAMs
*Wire per Clock Loading
Table/Wiring Diagrams
Notes :
BA0-BA1
A0-A13
BA0-BA1 : SDRAMs D0-D7
A0-A13 : SDRAMs D0-D7
/RAS
/RAS : SDRAMs D0-D7
/CAS
/CAS : SDRAMs D0-D7
CKE0
/WE
Rev. 1.1 / May. 2005
CKE : SDRAMs D0-D7
/WE : SDRAMs D0-D7
1. DQ-to-I/O wiring is shown as recommended but
may be changed.
2. DQ/DQS/DM/CKE/S relationships must be
maintained as shown.
3. DQ, DQS, DM/DQS resistors : 22 Ohms +- 5%.
4. VDDID strap connections
(for memory device VDD, VDDQ):
STRAP OUT (OPEN) : VDD = VDDQ
STRAP IN (VSS) : VDD ≠ V DDQ
5. BAx, Ax, RAS, CAS, WE resistors : 5.1 Ohms +- 5%
5
1184pin Unbufferd DDR SDRAM DIMMs
FUNCTIONAL BLOCK DIAGRAM
512MB, 64M x 72 ECC Unbuffered DIMM : HYMD564726B[P]8[J]
/CS0
DQS0
DM0/DQS9
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQS4
DM4/DQS13
I/O7
I/O6
I/O1
DM
/CS
DQS
D0
I/O0
I/O5
I/O4
I/O3
I/O2
DQS1
DM1/DQS10
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
I/O7
I/O6
I/O1
DM
/CS
DQS
D1
I/O0
I/O5
I/O4
I/O3
I/O2
BA0-BA1
A0-A13
DM
I/O7
I/O6
I/O1
I/O0
I/O5
/CS
DQS
D2
I/O4
I/O3
I/O2
DM
I/O7
I/O6
I/O1
I/O0
I/O5
/CS
DQS
I/O0
I/O5
/CS
DQS
D5
I/O4
I/O3
I/O2
DM
I/O7
I/O6
I/O1
I/O0
I/O5
/CS
DQS
D6
I/O4
I/O3
I/O2
DM
I/O7
I/O6
I/O1
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D3
I/O4
I/O3
I/O2
VDD SPD
I/O0
I/O5
/CS
DQS
D7
I/O4
I/O3
I/O2
SPD
*Clock Wiring
VDD /VDDQ
DM
I/O7
I/O6
I/O1
I/O0
I/O5
/CS
DQS
DO-D8
VREF
DO-D8
DO-D8
VSS
D8
VDDID
SCL
I/O2
BA0-BA1 : SDRAMs D0-D8
A0-A13 : SDRAMs D0-D8
/CAS : SDRAMs D0-D8
CKE : SDRAMs D0-D8
/WE : SDRAMs D0-D8
Clock Input
SDRAMs
*CK0, /CK0
*CK1, /CK1
*CK2, /CK2
3 SDRAMs
3 SDRAMs
3 SDRAMs
Strap:see Note 4
Serial PD
I/O4
I/O3
/RAS : SDRAMs D0-D8
Rev. 1.1 / May. 2005
DM
I/O7
I/O6
I/O1
DQS7
DM7/DQS16
/RAS
/WE
I/O2
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
/CAS
CKE0
D4
DQS6
DM6/DQS15
DQS3
DM3/DQS12
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
DQS
I/O4
I/O3
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQS3
DM3/DQS12
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
I/O0
I/O5
/CS
DQS5
DM5/DQS14
DQS2
DM2/DQS11
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DM
I/O7
I/O6
I/O1
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
*Wire per Clock Loading
Table/Wiring Diagrams
SDA
W
P
A0
A1
A2
SA0 SA1 SA2
Notes :
1. DQ-to-I/O wiring is shown as recommended but
may be changed.
2. DQ/DQS/DM/CKE/S relationships must be
maintained as shown.
3. DQ, DQS, DM/DQS resistors : 22 Ohms +- 5%.
4. VDDID strap connections
(for memory device VDD, VDDQ):
STRAP OUT (OPEN) : VDD = VDDQ
STRAP IN (VSS) : VDD ≠ V DDQ
5. BAx, Ax, RAS, CAS, WE resistors : 5.1 Ohms +- 5%
6
1184pin Unbufferd DDR SDRAM DIMMs
FUNCTIONAL BLOCK DIAGRAM
1GB, 128M x 64 Unbuffered DIMM : HYMD512646B[P]8[J]
/S1
/S0
DQS4
DM4
DQS0
DM0
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D0
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D8
/S
DQS
D4
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
D12
D12
DQS5
DM5
DQS1
DM1
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D1
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D9
DQS2
DM2
/S
DQS
D5
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
D13
DQS6
DM6
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D2
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D10
DQS3
DM3
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D6
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
D14
DQS7
DM7
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
VDDSPD
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D3
DO-D15
VREF
DO-D15
VSS
DO-D15
VDDID
Strap:see Note 4
A0-A13
/S
Serial PD
SCL
BA0-BA1-> : SDRAMs D0-D15
A0-A13-> : SDRAMs D0-D15
CKE : SDRAMs D8-D15
/RAS : SDRAMs D0-D15
/CAS
/CAS : SDRAMs D0-D15
CKE0
CKE : SDRAMs D0-D7
Rev. 1.1 / May. 2005
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D11
CKE1
/RAS
/WE
DQS
DQS
D7
DQS
D15
SPD
VDD/VDDQ
BA0-BA1
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/WE : SDRAMs D0-D15
SDA
WP
A0
A1
A2
SA0 SA1SA2
* Clock Wiring
Clock Input
SDRAMs
*CK0,/CK0
*CK1,/CK1
*CK2,/CK2
4 SDRAMs
6 SDRAMs
6 SDRAMs
* Wire per Clock Loading
Table/Wiring Diagrams
Note :
1. DQ-to-I/O wiring is shown as recommended but may be
changed.
2. DQ/DQS/DM/CKE/S relationships must be maintained as shown.
3. DQ,DQS,DM/DQS resistors : 22 Ohms ? 5%
4. VDDID strap connections (for memory device VDD, VDDQ) :
STRAP OUT (OPEN) : VDD = VDDQ
STRAP IN (VSS) : VDD ≠ VDDQ
5. BAx, Ax, /RAS, /CAS, /WE resistors : 3 Ohms ? 5%
7
1184pin Unbufferd DDR SDRAM DIMMs
FUNCTIONAL BLOCK DIAGRAM
1GB, 128M x 72 ECC Unbuffered DIMM : HYMD512726B[P]8[J]
/S1
/S0
DQS4
DM4
DQS0
DM0
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D0
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
D8
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D1
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D9
DQS2
DM2
DQS
D4
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
D12
D12
/S
DQS
D5
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
D13
DQS6
DM6
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D2
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D10
DQS3
DM3
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D6
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
D14
DQS7
DM7
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
DQS
D3
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
DQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D11
DQS8
DM8
D7
Serial PD
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
/S
D8
DQS
DM
I/O0
I/O1
I/O6
I/O7
I/O2
I/O3
I/O4
I/O5
/S
D17
BA0-BA1-> : SDRAMs D0-D17
A0-A13-> : SDRAMs D0-D17
CKE : SDRAMs D8-D17
/RAS : SDRAMs D0-D17
/CAS : SDRAMs D0-D17
CKE : SDRAMs D0-D8
/WE : SDRAMs D0-D17
DQS
SDA
WP
A0
A1
A2
SA0 SA1 SA2
VDDSPD
VDD/
VDDQ
VREF
VSS
VDDID
DQS
DQS
D15
* Clock Wiring
SCL
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
Rev. 1.1 / May. 2005
/S
DQS5
DM5
DQS1
DM1
BA0-BA1
A0-A13
CKE1
/RAS
/CAS
CKE0
/WE
DM
I/O7
I/O6
I/O1
I/O0
I/O5
I/O4
I/O3
I/O2
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
Clock Input
SDRAMs
*CK0,/CK0
6 SDRAMs
*CK1,/CK1
6 SDRAMs
*CK2,/CK2
6 SDRAMs
* Wire per Clock Loading
Table/Wiring Diagrams
Note :
1. DQ-to-I/O wiring is shown as
recommended
but may be changed.
SPD
2. DQ/DQS/DM/CKE/S relationships
must
be maintained as shown.
DO-D15
3. DQ,DQS,DM/DQS resistors
: 22 Ohms ? 5%
DO-D15
4. VDDID strap connections
(for memory device VDD, VDDQ) :
DO-D15
STRAP OUT (OPEN) : VDD = VDDQ
Strap:see Note 4
STRAP IN (VSS) : VDD ≠ VDDQ
5. BAx, Ax, /RAS, /CAS, /WE
resistors : 3 Ohms ? 5%
8
1184pin Unbufferd DDR SDRAM DIMMs
ABSOLUTE MAXIMUM RATINGS1
Parameter
Symbol
Rating
TA
0 ~ 70
o
C
Storage Temperature
TSTG
-55 ~ 150
o
C
Voltage on VDD relative to VSS
VDD
-1.0 ~ 3.6
V
Voltage on VDDQ relative to VSS
VDDQ
-1.0 ~ 3.6
V
Voltage on inputs relative to Vss
VINPUT
-1.0 ~ 3.6
V
VIO
-0.5 ~3.6
V
Operating Temperature (Ambient)
Voltage on I/O pins relative to Vss
Output Short Circuit Current
Soldering Temperature ⋅ Time
IOS
50
TSOLDER
260 ⋅ 10
Unit
mA
o
C ⋅ Sec
Note:
1. Operation at above absolute maximum rating can adversely affect device reliability
DC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS = 0V)
Parameter
Power Supply Voltage (DDR 200, 266, 333)
Symbol
Min
Typ.
Max
Unit
VDD
2.3
2.5
2.7
V
Note
VDD
2.5
2.6
2.7
V
Power Supply Voltage (DDR 200, 266, 333)
VDDQ
2.3
2.5
2.7
V
1
Power Supply Voltage (DDR 400)
VDDQ
2.5
2.6
2.7
V
1,2
Input High Voltage
VIH
VREF + 0.15
-
VDDQ + 0.3
V
Input Low Voltage
VIL
-0.3
-
VREF - 0.15
V
Termination Voltage
VTT
VREF - 0.04
VREF
VREF + 0.04
V
VREF
0.49*VDDQ
0.5*VDDQ
0.51*VDDQ
V
VIN(DC)
-0.3
-
VDDQ+0.3
V
Power Supply Voltage (DDR 400)
Reference Voltage
Input Voltage Level, CK and CK inputs
Input Differential Voltage, CK and CK inputs
2
3
4
VID(DC)
0.36
-
VDDQ+0.6
V
5
VI(RATIO)
0.71
-
1.4
-
6
Input Leakage Current
ILI
-2
-
2
uA
7
Output Leakage Current
ILO
-5
-
5
uA
8
IOH
-16.8
-
-
mA
IOL
16.8
-
-
mA
IOH
-13.6
-
-
mA
IOL
13.6
-
-
mA
V-I Matching: Pullup to Pulldown Current Ratio
Output High Current
Normal Strength
(min VDDQ, min VREF, min VTT)
Output Driver
(VOUT=VTT ± 0.84) Output Low Current
(min VDDQ, max VREF, max VTT)
Half Strength Out- Output High Current
put Driver
(min VDDQ, min VREF, min VTT)
(VOUT=VTT ± 0.68) Output Low Current
(min VDDQ, max VREF, max VTT)
Note:
1. VDDQ must not exceed the level of VDD.
2. For DDR400, VDD=2.6V ± 0.1V, VDDQ=2.6V ± 0.1V
3. VIL (min) is acceptable -1.5V AC pulse width with < 5ns of duration.
4. VREF is expected to be equal to 0.5*VDDQ of the transmitting device, and to track variations in the dc level of the same. Peak to
peak noise on VREF may not exceed ± 2% of the DC value.
5. VID is the magnitude of the difference between the input level on CK and the input level on /CK.
6. The ratio of the pullup current to the pulldown current is specified for the same temperature and voltage, over the entire temperature and voltage range, for device drain to source voltages from 0.25V to 1.0V. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation. The full variation in the ratio of the maximum to minimum
pullup and pulldown current will not exceed 1/7 for device drain to source voltages from 0.1 to 1.0.
7. VIN=0 to VDD, All other pins are not tested under VIN =0V.
8. DQs are disabled, VOUT=0 to VDDQ.
Rev. 1.1 / May. 2005
9
1184pin Unbufferd DDR SDRAM DIMMs
IDD SPECIFICATION AND CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
256MB, 32M x 64 Unbuffered DIMM: HYMD532646B[P]6[J]
Symbol
Speed
Test Condition
Unit
DDR400B
DDR333
DDR266B
IDD0
One bank; Active - Precharge; tRC=tRC(min);
tCK=tCK(min); DQ,DM and DQS inputs changing
twice per clock cycle; address and control inputs
changing once per clock cycle
600
560
480
mA
IDD1
One bank; Active - Read - Precharge; Burst
Length=2; tRC=tRC(min); tCK=tCK(min); address
and control inputs changing once per clock cycle
800
720
600
mA
IDD2P
All banks idle; Power down mode; CKE=Low,
tCK=tCK(min)
40
40
40
mA
IDD2F
/CS=High, All banks idle; tCK=tCK(min); CKE=
High; address and control inputs changing once
per clock cycle. VIN=VREF for DQ, DQS and DM
140
140
140
mA
IDD3P
One bank active ; Power down mode; CKE=Low,
tCK=tCK(min)
48
48
48
mA
IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge; tRC=tRAS(max); tCK=tCK(min); DQ, DM
and DQS inputs changing twice per clock cycle;
Address and other control inputs changing once
per clock cycle
200
180
160
mA
IDD4R
Burst=2; Reads; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); IOUT=0mA
1120
1000
840
mA
IDD4W
Burst=2; Writes; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); DQ, DM and DQS
inputs changing twice per clock cycle
1320
1120
1000
mA
IDD5
tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh
1200
1120
1040
mA
IDD6
CKE=<0.2V; External clock on;
tCK =tCK(min)
Normal
20
20
20
mA
Low Power
10
10
10
mA
IDD7
Four bank interleaving with BL=4 Refer to the following page for detailed test condition
2160
1840
1520
mA
Note
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.1 / May. 2005
10
1184pin Unbufferd DDR SDRAM DIMMs
IDD SPECIFICATION AND CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
512MB, 64M x 64 Unbuffered DIMM: HYMD564646B[P]8[J]
Symbol
Speed
Test Condition
DDR400B
DDR333
DDR266B
Unit
IDD0
One bank; Active - Precharge; tRC=tRC(min);
tCK=tCK(min); DQ,DM and DQS inputs changing
twice per clock cycle; address and control inputs
changing once per clock cycle
1200
1120
960
mA
IDD1
One bank; Active - Read - Precharge; Burst
Length=2; tRC=tRC(min); tCK=tCK(min); address
and control inputs changing once per clock cycle
1600
1440
1200
mA
IDD2P
All banks idle; Power down mode; CKE=Low,
tCK=tCK(min)
80
80
80
mA
IDD2F
/CS=High, All banks idle; tCK=tCK(min); CKE=
High; address and control inputs changing once
per clock cycle. VIN=VREF for DQ, DQS and DM
280
280
280
mA
IDD3P
One bank active ; Power down mode; CKE=Low,
tCK=tCK(min)
96
96
96
mA
IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge; tRC=tRAS(max); tCK=tCK(min); DQ, DM
and DQS inputs changing twice per clock cycle;
Address and other control inputs changing once
per clock cycle
400
360
320
mA
IDD4R
Burst=2; Reads; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); IOUT=0mA
2240
2000
1680
mA
IDD4W
Burst=2; Writes; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); DQ, DM and DQS
inputs changing twice per clock cycle
2240
2000
1680
mA
IDD5
tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh
2400
2240
2080
mA
IDD6
CKE=<0.2V; External clock on;
tCK =tCK(min)
Normal
40
40
40
mA
Low Power
20
20
20
mA
IDD7
Four bank interleaving with BL=4 Refer to the following page for detailed test condition
4320
3680
3040
mA
Note
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.1 / May. 2005
11
1184pin Unbufferd DDR SDRAM DIMMs
IDD SPECIFICATION AND CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
512MB, 64M x 72 ECC Unbuffered DIMM: HYMD564726B[P]8[J]
Symbol
Speed
Test Condition
Unit
DDR400B
DDR333
DDR266B
IDD0
One bank; Active - Precharge; tRC=tRC(min);
tCK=tCK(min); DQ,DM and DQS inputs changing
twice per clock cycle; address and control inputs
changing once per clock cycle
1350
1260
1080
mA
IDD1
One bank; Active - Read - Precharge; Burst
Length=2; tRC=tRC(min); tCK=tCK(min); address
and control inputs changing once per clock cycle
1800
1620
1350
mA
IDD2P
All banks idle; Power down mode; CKE=Low,
tCK=tCK(min)
90
90
90
mA
IDD2F
/CS=High, All banks idle; tCK=tCK(min); CKE=
High; address and control inputs changing once
per clock cycle. VIN=VREF for DQ, DQS and DM
315
315
315
mA
IDD3P
One bank active ; Power down mode; CKE=Low,
tCK=tCK(min)
108
108
108
mA
IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge; tRC=tRAS(max); tCK=tCK(min); DQ, DM
and DQS inputs changing twice per clock cycle;
Address and other control inputs changing once
per clock cycle
450
105
360
mA
IDD4R
Burst=2; Reads; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); IOUT=0mA
2520
2250
1890
mA
IDD4W
Burst=2; Writes; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); DQ, DM and DQS
inputs changing twice per clock cycle
2520
2250
1890
mA
IDD5
tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh
2700
2520
2340
mA
IDD6
CKE=<0.2V; External clock on;
tCK =tCK(min)
Normal
45
45
45
mA
Low Power
23
23
23
mA
IDD7
Four bank interleaving with BL=4 Refer to the following page for detailed test condition
4860
4140
3420
mA
Note
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.1 / May. 2005
12
1184pin Unbufferd DDR SDRAM DIMMs
IDD SPECIFICATION AND CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
1GB, 128M x 64 Unbuffered DIMM: HYMD512646B[P]8[J]
Symbol
Speed
Test Condition
Unit
DDR400B
DDR333
DDR266B
IDD0
One bank; Active - Precharge; tRC=tRC(min);
tCK=tCK(min); DQ,DM and DQS inputs changing
twice per clock cycle; address and control inputs
changing once per clock cycle
1600
1480
1280
mA
IDD1
One bank; Active - Read - Precharge; Burst
Length=2; tRC=tRC(min); tCK=tCK(min); address
and control inputs changing once per clock cycle
2000
1800
1520
mA
IDD2P
All banks idle; Power down mode; CKE=Low,
tCK=tCK(min)
160
160
160
mA
IDD2F
/CS=High, All banks idle; tCK=tCK(min); CKE=
High; address and control inputs changing once
per clock cycle. VIN=VREF for DQ, DQS and DM
560
560
560
mA
IDD3P
One bank active; Power down mode; CKE=Low,
tCK=tCK(min)
192
192
192
mA
IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge; tRC=tRAS(max); tCK=tCK(min); DQ, DM
and DQS inputs changing twice per clock cycle;
Address and other control inputs changing once
per clock cycle
800
720
640
mA
IDD4R
Burst=2; Reads; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); IOUT=0mA
2640
2360
2000
mA
IDD4W
Burst=2; Writes; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); DQ, DM and DQS
inputs changing twice per clock cycle
2640
2360
2000
mA
IDD5
tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh
2800
2600
2400
mA
CKE=<0.2V; External clock on;
tCK =tCK(min)
Normal
IDD6
80
80
80
mA
Low Power
40
40
40
mA
IDD7
Four bank interleaving with BL=4 Refer to the following page for detailed test condition
4720
4040
3360
mA
Note
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.1 / May. 2005
13
1184pin Unbufferd DDR SDRAM DIMMs
IDD SPECIFICATION AND CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
1GB, 128M x 72 ECC Unbuffered DIMM: HYMD512726B[P]8[J]
Symbol
Speed
Test Condition
DDR400B
DDR333
DDR266B
Unit
IDD0
One bank; Active - Precharge; tRC=tRC(min);
tCK=tCK(min); DQ,DM and DQS inputs changing
twice per clock cycle; address and control inputs
changing once per clock cycle
1800
1665
1440
mA
IDD1
One bank; Active - Read - Precharge; Burst
Length=2; tRC=tRC(min); tCK=tCK(min); address
and control inputs changing once per clock cycle
2250
2025
1710
mA
IDD2P
All banks idle; Power down mode; CKE=Low,
tCK=tCK(min)
180
180
180
mA
IDD2F
/CS=High, All banks idle; tCK=tCK(min); CKE=
High; address and control inputs changing once
per clock cycle. VIN=VREF for DQ, DQS and DM
630
630
630
mA
IDD3P
One bank active ; Power down mode; CKE=Low,
tCK=tCK(min)
216
216
216
mA
IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge; tRC=tRAS(max); tCK=tCK(min); DQ, DM
and DQS inputs changing twice per clock cycle;
Address and other control inputs changing once
per clock cycle
900
810
720
mA
IDD4R
Burst=2; Reads; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); IOUT=0mA
2970
2655
2250
mA
IDD4W
Burst=2; Writes; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK=tCK(min); DQ, DM and DQS
inputs changing twice per clock cycle
2970
2655
2250
mA
IDD5
tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh
3150
2925
2700
mA
CKE=<0.2V; External clock on;
tCK =tCK(min)
Normal
IDD6
90
90
90
mA
Low Power
45
45
45
mA
IDD7
Four bank interleaving with BL=4 Refer to the following page for detailed test condition
5310
4545
3780
mA
Note
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.1 / May. 2005
14
1184pin Unbufferd DDR SDRAM DIMMs
AC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS = 0V)
Parameter
Symbol
Min
Max
Unit
Note
Input High (Logic 1) Voltage, DQ, DQS and DM signals
VIH(AC)
VREF + 0.31
-
V
Input Low (Logic 0) Voltage, DQ, DQS and DM signals
VIL(AC)
-
VREF - 0.31
V
Input Differential Voltage, CK and /CK inputs
VID(AC)
0.7
VDDQ + 0.6
V
1
Input Crossing Point Voltage, CK and /CK inputs
VIX(AC)
0.5*VDDQ-0.2
0.5*VDDQ+0.2
V
2
Note:
1. VID is the magnitude of the difference between the input level on CK and the input on /CK.
2. The value of VIX is expected to equal 0.5*V DDQ of the transmitting device and must track variations in the DC level of the same.
AC OPERATING TEST CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Value
Unit
Reference Voltage
Parameter
VDDQ x 0.5
V
Termination Voltage
VDDQ x 0.5
V
AC Input High Level Voltage (VIH, min)
VREF + 0.31
V
AC Input Low Level Voltage (VIL, max)
VREF - 0.31
V
Input Timing Measurement Reference Level Voltage
VREF
V
Output Timing Measurement Reference Level Voltage
VTT
V
Input Signal maximum peak swing
1.5
V
1
V/ns
Input minimum Signal Slew Rate
Termination Resistor (RT)
50
Ω
Series Resistor (RS)
25
Ω
Output Load Capacitance for Access Time Measurement (CL)
30
pF
OUTPUT LOAD CIRCUIT
VTT
RT=50Ω
Output
Zo=50Ω
VREF
CL=30pF
Rev. 1.1 / May. 2005
15
1184pin Unbufferd DDR SDRAM DIMMs
CAPACITANCE (TA=25oC, f=100MHz)
256MB: HYMD532646B[P]6[J]
Input/Output Pins
Symbol
Min
Max
Unit
A0 ~ A12, BA0, BA1
CIN1
40
52
pF
/RAS, /CAS, /WE
CIN2
40
52
pF
CKE
CIN3
40
52
pF
/CS
CIN4
40
52
pF
CK0, /CK0, CK1, /CK1, CK2, /CK2
CIN5
22
32
pF
DM0 ~ DM7
CIN6
7
12
pF
DQ0 ~ DQ63, DQS0 ~ DQS7
CIO1
7
12
pF
Symbol
Min
Max
Unit
A0 ~ A12, BA0, BA1
CIN1
58
71
pF
/RAS, /CAS, /WE
CIN2
58
71
pF
CKE
CIN3
58
72
pF
/CS
CIN4
58
72
pF
CK0, /CK0, CK1, /CK1, CK2, /CK2
CIN5
25
40
pF
DM0 ~ DM7
CIN6
7
12
pF
DQ0 ~ DQ63, DQS0 ~ DQS7
CIO1
7
12
pF
Symbol
Min
Max
Unit
A0 ~ A12, BA0, BA1
CIN1
60
75
pF
/RAS, /CAS, /WE
CIN2
60
75
pF
CKE
CIN3
60
75
pF
/CS
CIN4
60
75
pF
CK0, /CK0, CK1, /CK1, CK2, /CK2
CIN5
27
45
pF
DM0 ~ DM7
CIN6
7
12
pF
DQ0 ~ DQ63, DQS0 ~ DQS7
CIO1
7
12
pF
CB0 ~ CB7
CIO2
7
12
pF
512MB: HYMD564646B[P]8[J]
Input/Output Pins
512MB (with ECC): HYMD564726B[P]8[J]
Input/Output Pins
Rev. 1.1 / May. 2005
16
1184pin Unbufferd DDR SDRAM DIMMs
CAPACITANCE (TA=25oC, f=100MHz)
1GB: HYMD512646B[P]8[J]
Input/Output Pins
Symbol
Min
Max
Unit
CIN1
90
104
pF
/RAS, /CAS, /WE
CIN2
90
104
pF
CKE0, CKE1
CIN3
58
72
pF
/CS0, /CS1
CIN4
58
72
pF
CK0, /CK0, CK1, /CK1, CK2, /CK2
CIN5
30
45
pF
DM0 ~ DM7
CIN6
12
18
pF
DQ0 ~ DQ63, DQS0 ~ DQS7
CIO1
12
18
pF
Symbol
Min
Max
Unit
A0 ~ A12, BA0, BA1
CIN1
95
110
pF
/RAS, /CAS, /WE
CIN2
95
110
pF
CKE0, CKE1
CIN3
60
80
pF
/CS0,/CS1
CIN4
60
80
pF
CK0, /CK0, CK1, /CK1, CK2, /CK2
CIN5
32
45
pF
DM0 ~ DM7
CIN6
12
18
pF
DQ0 ~ DQ63, DQS0 ~ DQS7
CIO1
12
18
pF
CB0 ~ CB7
CIO2
12
18
pF
A0 ~ A12, BA0, BA1
1GB (with ECC): HYMD512726B[P]8[J]
Input/Output Pins
Rev. 1.1 / May. 2005
17
1184pin Unbufferd DDR SDRAM DIMMs
AC CHARACTERISTICS (note: 1 - 9 / AC operating conditions unless otherwise noted)
Parameter
Symbol
DDR400B
DDR333
DDR266A
DDR266B
DDR200
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
UNIT
Row Cycle Time
tRC
55
-
60
-
65
-
65
-
70
-
ns
Auto Refresh Row
Cycle Time
tRFC
70
-
72
-
75
-
75
-
80
-
ns
Row Active Time
tRAS
40
70K
42
70K
45
120K
45
120K
50
120K
ns
tRAP
tRCD or
tRASmin
-
tRCD or
tRASmin
-
tRCD or
tRASmin
-
tRCD or
tRASmin
-
tRCD or
tRASmin
-
ns
Row Address to
Column Address Delay
tRCD
15
-
18
-
20
-
20
-
20
-
ns
Row Active to Row
Active Delay
tRRD
10
-
12
-
15
-
15
-
15
-
ns
Column Address to
Column Address Delay
tCCD
1
-
1
-
1
-
1
-
1
-
tCK
Row Precharge Time
tRP
15
-
18
-
20
-
20
-
20
-
ns
Write Recovery Time
tWR
15
-
15
-
15
-
15
-
15
-
ns
Internal Write to Read
Command Delay
tWTR
2
-
1
-
1
-
1
-
1
-
tCK
tDAL
(tWR/
tCK)
+
(tRP/tCK)
-
(tWR/
tCK)
+
(tRP/tCK)
-
(tWR/
tCK)
+
(tRP/tCK)
-
(tWR/
tCK)
+
(tRP/tCK)
-
(tWR/
tCK)
+
(tRP/tCK)
-
tCK
5
10
-
-
-
-
-
-
-
-
-
-
6
12
7.5
12
7.5
12
8.0
12
ns
-
-
7.5
12
7.5
12
10
12
10
12
ns
Active to Read with
Auto Precharge Delay
Auto Precharge Write
Recovery + Precharge
Time22
CL = 3
System
Clock Cycle CL = 2.5
Time24
CL = 2
tCK
Clock High Level Width
tCH
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
tCK
Clock Low Level Width
tCL
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
tCK
Data-Out edge to Clock
edge Skew
tAC
-0.7
0.7
-0.7
0.7
-0.75
0.75
-0.75
0.75
-0.75
0.75
ns
-0.55
0.55
-0.6
0.6
-0.75
0.75
-0.75
0.75
-0.75
0.75
ns
tDQSQ
-
0.4
-
0.45
-
0.5
-
0.5
-
0.6
ns
tQH
tHP
-tQHS
-
tHP
-tQHS
-
tHP
-tQHS
-
tHP
-tQHS
-
tHP
-tQHS
-
ns
tHP
min
(tCL,tCH)
-
min
(tCL,tCH)
-
min
(tCL,tCH)
-
min
(tCL,tCH)
-
min
(tCL,tCH)
-
ns
tQHS
-
0.5
-
0.55
-
0.75
-
0.75
-
0.75
ns
DQS-Out edge to Clock
tDQSCK
edge Skew
DQS-Out edge to DataOut edge Skew21
Data-Out hold time
from DQS20
Clock Half Period19,20
Data Hold Skew
Factor20
Valid Data Output
Window
Rev. 1.1 / May. 2005
tDV
tQH-tDQSQ
tQH-tDQSQ
tQH-tDQSQ
tQH-tDQSQ
tQH-tDQSQ
ns
18
1184pin Unbufferd DDR SDRAM DIMMs
- Continue
Parameter
Symbol
DDR400B
DDR333
DDR266A
DDR266B
DDR200
UNIT
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
tHZ
-0.7
0.7
-0.7
0.7
-0.75
0.75
-0.75
0.75
-0.8
0.8
ns
tLZ
-0.7
0.7
-0.7
0.7
-0.75
0.75
-0.75
0.75
-0.8
0.8
ns
tIS
0.6
-
0.75
-
0.9
-
0.9
-
1.1
-
ns
tIH
0.6
-
0.75
-
0.9
-
0.9
-
1.1
-
ns
tIS
0.7
-
0.8
-
1.0
-
1.0
-
1.1
-
ns
tIH
0.7
-
0.8
-
1.0
-
1.0
-
1.1
-
ns
tIPW
2.2
-
2.2
-
2.2
-
2.2
-
2.5
-
ns
Write DQS High Level Width
tDQSH
0.35
-
0.35
-
0.35
-
0.35
-
0.35
-
tCK
Write DQS Low Level Width
tDQSL
0.35
-
0.35
-
0.35
-
0.35
-
0.35
-
tCK
Clock to First Rising edge of DQSIn
tDQSS
0.72
1.25
0.75
1.25
0.75
1.25
0.75
1.25
0.75
1.25
tCK
DQS falling edge to CK setup time
tDSS
0.2
-
0.2
-
0.2
-
0.2
-
0.2
-
tCK
DQS falling edge hold time from
CK
tDSH
0.2
-
0.2
-
0.2
-
0.2
-
0.2
-
tCK
DQ & DM input setup time25
tDS
0.4
-
0.45
-
0.5
-
0.5
-
0.6
-
ns
DQ & DM input hold time25
tDH
0.4
-
0.45
-
0.5
-
0.5
-
0.6
-
ns
DQ & DM Input Pulse Width17
tDIPW
1.75
-
1.75
-
1.75
-
1.75
-
2
-
ns
Read DQS Preamble Time
tRPRE
0.9
1.1
0.9
1.1
0.9
1.1
0.9
1.1
0.9
1.1
tCK
Read DQS Postamble Time
tRPST
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
tCK
0
-
0
-
0
-
0
-
0
-
ns
-
0.25
-
0.25
-
0.25
-
0.25
-
tCK
Data-out high-impedance window
from CK,/CK10
Data-out low-impedance window
from CK, /CK10
Input Setup Time (fast slew
rate)14,16-18
Input Hold Time (fast slew
rate)14,16-18
Input Setup Time (slow slew
rate)15-18
Input Hold Time (slow slew
rate)15-18
Input Pulse Width17
Write DQS Preamble Setup Time12 tWPRES
Write DQS Preamble Hold Time
11
tWPREH 0.25
Write DQS Postamble Time
tWPST
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
tCK
Mode Register Set Delay
tMRD
2
-
2
-
2
-
2
-
2
-
tCK
tXSNR
75
-
75
-
75
-
75
-
80
-
ns
tXSRD
200
-
200
-
200
-
200
-
200
-
tCK
tREFI
-
7.8
-
7.8
-
7.8
-
7.8
-
7.8
us
Exit Self Refresh to non-Read
command23
Exit Self Refresh to Read
command
Average Periodic Refresh
Interval13,25
Rev. 1.1 / May. 2005
19
1184pin Unbufferd DDR SDRAM DIMMs
Note:
1. All voltages referenced to Vss.
2. Tests for ac timing, IDD, and electrical, ac and dc characteristics, may be conducted at nominal reference/supply voltage levels,
but the related specifications and device operation are guaranteed for the full voltage range specified.
3. Below figure represents the timing reference load used in defining the relevant timing parameters of the part. It is not intended to
be either a precise representation of the typical system environment nor a depiction of the actual load presented by a production
tester. System designers will use IBIS or other simulation tools to correlate the timing reference load to a system environment.
Manufacturers will correlate to their production test conditions (generally a coaxial transmission line terminated at the tester electronics).
VDDQ
Output
(VOUT)
50 Ω
30 pF
Figure: Timing Reference Load
4. AC timing and IDD tests may use a VIL to VIHswing of up to 1.5 V in the test environment, but input timing is still referenced to
VREF (or to the crossing point for CK, /CK), and parameter specifications are guaranteed for the specified ac input levels under
normal use conditions. The minimum slew rate for the input signals is 1 V/ns in the range between VIL(ac) and VIH(ac).
5. The ac and dc input level specifications are as defined in the SSTL_2 Standard (i.e., the receiver will effectively switch as a result
of the signal crossing the ac input level and will remain in that state as long as the signal does not ring back above (below) the
dc input LOW (HIGH) level.
6. Inputs are not recognized as valid until VREF stabilizes. Exception: during the period before VREF stabilizes, CKE < 0.2VDDQ is
recognized as LOW.
7. The CK, /CK input reference level (for timing referenced to CK, /CK) is the point at which CK and /CK cross; the input reference
level for signals other than CK, /CK is VREF.
8. The output timing reference voltage level is VTT.
9. Operation or timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must
be powered down and then restarted through the specified initialization sequence before normal operation can continue.
10. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to
a specific voltage level but specify when the device output is no longer driving (HZ), or begins driving (LZ).
11. The maximum limit for this parameter is not a device limit. The device will operate with a greater value for this parameter, but
system performance (bus turnaround) will degrade accordingly.
12. The specific requirement is that DQS be valid (HIGH, LOW, or at some point on a valid transition) on or before this CK edge. A
valid transition is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were previously in progress on the bus, DQS will be transitioning from High-Z to logic LOW. If a previous write was in progress, DQS could
be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on tDQSS.
13. A maximum of eight AUTO REFRESH commands can be posted to any given DDR SDRAM device.
14. For command/address input slew rate ≥ 1.0 V/ns.
15. For command/address input slew rate ≥ 0.5 V/ns and ＜ 1.0 V/ns
16. For CK & /CK slew rate ≥ 1.0 V/ns (single-ended)
17. These parameters guarantee device timing, but they are not necessarily tested on each device.
They may be guaranteed by device design or tester correlation.
18. Slew Rate is measured between VOH(ac) and VOL(ac).
19. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this
value can be greater than the minimum specification limits for tCL and tCH).
For example, tCL and tCH are = 50% of the period, less the half period jitter (tJIT(HP)) of the clock source, and less the half
period jitter due to crosstalk (tJIT(crosstalk)) into the clock traces.
Rev. 1.1 / May. 2005
20
1184pin Unbufferd DDR SDRAM DIMMs
20.tQH = tHP - tQHS, where:
tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL). tQHS accounts for 1) The
pulse duration distortion of on-chip clock circuits; and 2) The worst case push--out of DQS on one transition followed by the
worst case pull--in of DQ on the next transition, both of which are, separately, due to data pin skew and output pattern effects,
and p-channel to n-channel variation of the output drivers.
21. tDQSQ:
Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers for any given
cycle.
22. tDAL = (tWR/tCK) + (tRP/tCK)
For each of the terms above, if not already an integer, round to the next highest integer.
Example: For DDR266B at CL=2.5 and tCK=7.5 ns
tDAL = ((15 ns / 7.5 ns) + (20 ns / 7.5 ns)) clocks
= ((2) + (3)) clocks
= 5 clocks
23. In all circumstances, tXSNR can be satisfied using
tXSNR = tRFCmin + 1*tCK
24. The only time that the clock frequency is allowed to change is during self-refresh mode.
25. If refresh timing or tDS/tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid
READ can be executed.
Rev. 1.1 / May. 2005
21
1184pin Unbufferd DDR SDRAM DIMMs
SYSTEM CHARACTERISTICS CONDITIONS for DDR SDRAMS
The following tables are described specification parameters that required in systems using DDR devices to ensure
proper performannce. These characteristics are for system simulation purposes and are guaranteed by design.
Input Slew Rate for DQ/DM/DQS
AC CHARACTERISTICS
(Table a.)
DDR400
DDR333
DDR266
DDR200
PARAMETER
Symbol
min
max
min
max
min
max
min
max
DQ/DM/DQS input slew rate
measured between VIH(DC),
VIL(DC) and VIL(DC), VIH(DC)
DCSLEW
0.5
4.0
0.5
4.0
0.5
4.0
0.5
4.0
UNIT
Note
V/ns
1,12
Address & Control Input Setup & Hold Time Derating (Table b.)
Input Slew Rate
Delta tIS
Delta tIH
UNIT
Note
0.5 V/ns
0
0
ps
9
0.4 V/ns
+50
0
ps
9
0.3 V/ns
+100
0
ps
9
DQ & DM Input Setup & Hold Time Derating
(Table c.)
Input Slew Rate
Delta tDS
Delta tDH
UNIT
Note
0.5 V/ns
0
0
ps
11
0.4 V/ns
+75
0
ps
11
0.3 V/ns
+150
0
ps
11
DQ & DM Input Setup & Hold Time Derating for Rise/Fall Delta Slew Rate
Input Slew Rate
Delta tDS
(Table d.)
Delta tDH
UNIT
Note
± 0.0 ns/V
0
0
ps
10
± 0.25 ns/V
+50
+50
ps
10
± 0.5 ns/V
+100
+100
ps
10
Output Slew Rate Characteristics (for x4, x8 Devices)
Slew Rate Characteristic
Typical Range (V/
ns)
(Table e.)
Minimum (V/ns)
Maximum (V/ns)
Note
Pullup Slew Rate
1.2 - 2.5
1.0
4.5
1,3,4,6,7,8
Pulldown Slew Rate
1.2 - 2.5
1.0
4.5
2,3,4,6,7,8
Maximum (V/ns)
Note
Output Slew Rate Characteristics (for x16 Device) (Table f.)
Slew Rate Characteristic
Typical Range (V/
ns)
Minimum (V/ns)
Pullup Slew Rate
1.2 - 2.5
1.0
4.5
1,3,4,6,7,8
Pulldown Slew Rate
1.2 - 2.5
1.0
4.5
2,3,4,6,7,8
Output Slew Rate Matching Ratio Characteristics
Slew Rate Characteristic
Parameter
Output Slew Rate Matching Ratio
(Pullup to Pulldown)
Rev. 1.1 / May. 2005
DDR266A
(Table g.)
DDR266B
DDR200
min
max
min
max
min
max
-
-
-
-
0.71
1.4
Note
5,12
22
1184pin Unbufferd DDR SDRAM DIMMs
Note:
1. Pullup slew rate is characterized under the test conditions as shown in below Figure.
Test Point
Output
(VOUT)
50
Ω
VSSQ
Figure: Pullup Slew rate
2. Pulldown slew rate is measured under the test conditions shown in below Figure.
VDDQ
Output
(VOUT)
50Ω
Test Point
Figure: Pulldown Slew rate
3. Pullup slew rate is measured between (VDDQ/2 - 320 mV ± 250mV)
Pulldown slew rate is measured between (VDDQ/2 + 320mV ± 250mV)
Pullup and Pulldown slew rate conditions are to be met for any pattern of data, including all outputs switching and only one output
switching.
Example: For typical slew, DQ0 is switching
For minimum slew rate, all DQ bits are switching worst case pattern
For maximum slew rate, only one DQ is switching from either high to low, or low to high.
The remaining DQ bits remain the same as for previous state.
4. Evaluation conditions
Typical: 25 oC (Ambient), VDDQ = nominal, typical process
Minimum: 70 oC (Ambient), VDDQ = minimum, slow-slow process
Maximum: 0 oC (Ambient), VDDQ = Maximum, fast-fast process
5. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and voltage, over the entire temperature
and voltage range. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process
variation.
6. Verified under typical conditions for qualification purposes.
7. TSOP-II package devices only.
8. Only intended for operation up to 256 Mbps per pin.
9. A derating factor will be used to increase tIS and tIH in the case where the input slew rate is below 0.5 V/ns as shown in Table b.
The Input slew rate is based on the lesser of the slew rates determined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions.
10. A derating factor will be used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ, as shown in Tables c
& d. Input slew rate is based on the larger of AC-AC delta rise, fall rate and DC-DC delta rise, fall rate. Input slew rate is based on
the lesser of the slew rates determined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions. The
delta rise/fall rate is calculated as:
{1/(Slew Rate1)} - {1/(slew Rate2)}
For example:
If Slew Rate 1 is 0.5 V/ns and Slew Rate 2 is 0.4 V/ns, then the delta rise, fall rate is -0.5 ns/V. Using the table given, this would
result in the need for an increase in tDS and tDH of 100ps.
11. Table c is used to increase tDS and tDH in the case where the I/O slew rate is below 0.5 V/ns. The I/O slew rate is based on the
lesser of the AC-AC slew rate and the DC-DC slew rate. The input slew rate is based on the lesser of the slew rates determined by
either VIH(ac) to VIL(AC) or VIH(DC) to VIL(DC), and similarly for rising transitions.
12. DQS, DM, and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transitions through the DC region must be monotonic.
Rev. 1.1 / May. 2005
23
1184pin Unbufferd DDR SDRAM DIMMs
SIMPLIFIED COMMAND TRUTH TABLE
CKEn-1
CKEn
/CS
/RAS
/CAS
/WE
Extended Mode Register Set
Command
H
X
L
L
L
L
OP code
1,2
Mode Register Set
H
X
L
L
L
L
OP code
1,2
H
X
X
1
H
X
Device Deselect
No Operation
Bank Active
Read
Read with Autoprecharge
Write
Write with Autoprecharge
Precharge All Banks
Precharge selected Bank
Read Burst Stop
Auto Refresh
Entry
Self Refresh
Precharge Power
Down Mode
Active Power Down
Mode
H
X
H
X
X
X
L
H
H
H
L
L
H
H
L
H
L
H
ADDR
A10/AP
RA
CA
BA
V
L
H
L
V
1
1
1,3
1
H
X
L
H
L
L
CA
H
X
L
L
H
L
X
H
X
L
H
H
L
X
1
H
H
L
L
L
H
X
1
H
L
L
L
L
H
H
X
X
X
L
H
H
H
Exit
L
H
Entry
H
L
Exit
L
H
Entry
H
L
Exit
L
H
H
V
Note
H
X
L
V
1,4
1,5
1
1
X
1
H
X
X
X
1
L
H
H
H
1
H
X
X
X
L
H
H
H
H
X
X
X
L
V
V
V
X
1
1
1
X
1
X
1
Note :
1. DM
states are
Don’t
Care.
Refer to
below
Write
Mask Care,
Truth V=Valid
Table. Data Input, OP Code=Operand Code, NOP=No Operation )
( H=Logic
High
Level,
L=Logic
Low
Level,
X=Don’t
2. OP Code(Operand Code) consists of A0~A12 and BA0~BA1 used for Mode Registering duing Extended MRS or MRS.
Before entering Mode Register Set mode, all banks must be in a precharge state and MRS command can be issued after tRP
period from Prechagre command.
3. If a Read with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+tRP).
4. If a Write with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+1+tWR+tRP). Write Recovery Time(tWR) is needed to guarantee that the last data has been
completely written.
5. If A10/AP is High when Row Precharge command being issued, BA0/BA1 are ignored and all banks are selected to be precharged.
WRITE MASK TRUTH TABLE
CKEn-1
CKEn
/CS, /RAS, /CAS, /WE
DM
Data Write
Function
H
X
X
L
ADDR
A10/AP
X
BA
Note
1
Data-In Mask
H
X
X
H
X
1
Note:
1. Write Mask command masks burst write data with reference to LDQS/UDQS(Data Strobes) and it is not related with read data.
In case of x16 data I/O, LDM and UDM control lower byte(DQ0~7) and Upper byte(DQ8~15) respectively.
Rev. 1.1 / May. 2005
24
1184pin Unbufferd DDR SDRAM DIMMs
PACKAGE DIMENSIONS
256MB, 32M x 64 Unbuffered DIMM: HYMD532646B[P]6[J]
Unit:
Front
Millimeters
Inches
133.35
5.25
131.35
5.171
128.95
(2X)4.00
.157
5.077
2.30
.91
(2) 0
2.5
0.098
Back
17.80
.700
10.0
.394
31.75
1.250
Side
3.18
.125MAX
(Front)
1.27+/-0.10
.050+/-.004
Rev. 1.1 / May. 2005
25
1184pin Unbufferd DDR SDRAM DIMMs
PACKAGE DIMENSIONS
512MB, 64M x 64 Unbuffered DIMM: HYMD564646B[P]8[J]
Front
Unit:
Millimeters
Inches
133.35
5.25
131.35
128.95
5.077
(2X)4.00
0.157
5.171
2.30
0.91
(2) 0
2.5
0.098
17.80
0.700
10.0
0.394
31.75
1.250
Back
Side
3.18
0.125MAX
(Front)
1.27+/-0.10
0.050+/-0.004
Rev. 1.1 / May. 2005
26
1184pin Unbufferd DDR SDRAM DIMMs
PACKAGE DIMENSIONS
512MB, 64M x 72 ECC Unbuffered DIMM: HYMD564726B[P]8[J]
Front
Unit:
133.35
5.25
Millimeters
Inches
131.35
128.95
5.077
(2X)4.00
0.157
5.171
2.30
0.91
(2) 0
2.5
0.098
17.80
0.700
10.0
0.394
31.75
1.250
Back
Side
3.18
0.125MAX
(Front)
1.27+/-0.10
0.050+/-0.004
Rev. 1.1 / May. 2005
27
1184pin Unbufferd DDR SDRAM DIMMs
PACKAGE DIMENSIONS
1GB, 128M x 64 Unbuffered DIMM : HYMD564646B[P]8[J]
Front
Unit:
133.35
5.25
Millimeters
Inches
131.35
128.95
5.077
(2X)4.00
0.157
5.171
2.30
0.91
(2) 0
2.5
0.098
17.80
0.700
10.0
0.394
31.75
1.250
Back
Side
4.00
0.157MAX
(Front)
1.27+/-0.10
0.050+/-0.004
Rev. 1.1 / May. 2005
28
1184pin Unbufferd DDR SDRAM DIMMs
PACKAGE DIMENSIONS
1GB, 128M x 72 ECC Unbuffered DIMM: HYMD512726B[P]8[J]
Front
Unit:
133.35
5.25
Millimeters
Inches
131.35
128.95
5.077
(2X)4.00
0.157
5.171
2.30
0.91
(2) 0
2.5
0.098
17.80
0.700
10.0
0.394
31.75
1.250
Back
Side
4.00
0.157MAX
(Front)
1.27+/-0.10
0.050+/-0.004
Rev. 1.1 / May. 2005
29
1184pin Unbufferd DDR SDRAM DIMMs
REVISION HISTORY
Revision
History
Date
1.0
First Version Release - Datasheet coverage is changed from an individual module part to a
component based module family
Feb. 2005
1.1
Corrected PIN DESCRIPTION and PIN ASSIGNMENT Tables
May. 2005
Rev. 1.1 / May. 2005
Remark
30