128Mx72 bits Low Profile Registered DDR SDRAM DIMM HYMD512G726B(L)4M-M/K/H/L DESCRIPTION Preliminary Hynix HYMD512G726B(L)4M-M/K/H/L series is low profile registered 184-pin double data rate Synchronous DRAM Dual In-Line Memory Modules (DIMMs) which are organized as 128M x 72 high-speed memory arrays. HYMD512G726B(L)4M-M/K/H/L series consists of eighteen 128M x 4 DDR SDRAM in 400mil TSOP II packages on a 184pin glass-epoxy substrate. Hynix HYMD512G726B(L)4M-M/K/H/L series provide a high performance 8-byte interface in 5.25" width form factor of industry standard. It is suitable for easy interchange and addition. Hynix HYMD512G726B(L)4M-M/K/H/L series is designed for high speed of up to 133MHz and offers fully synchronous operations referenced to both rising and falling edges of differential clock inputs. While all addresses and control inputs are latched on the rising edges of the clock, Data, Data strobes and Write data masks inputs are sampled on both rising and falling edges of it. The data paths are internally pipelined and 2-bit prefetched to achieve very high bandwidth. All input and output voltage levels are compatible with SSTL_2. High speed frequencies, programmable latencies and burst lengths allow variety of device operation in high performance memory system. Hynix HYMD512G726B(L)4M-M/K/H/L series incorporates SPD(serial presence detect). Serial presence detect function is implemented via a serial 2,048-bit EEPROM. The first 128 bytes of serial PD data are programmed by Hynix to identify DIMM type, capacity and other the information of DIMM and the last 128 bytes are available to the customer. FEATURES • 1GB (128M x 72) Low Profile Registered DDR DIMM based on 128M x 4 DDR SDRAM • Fully differential clock operations (CK & /CK) with 100/133MHz • JEDEC Standard 184-pin dual in-line memory module (DIMM) • Programmable CAS Latency 2 / 2.5 supported • • Error Check Correction (ECC) Capability Programmable Burst Length 2 / 4 / 8 with both sequential and interleave mode • Registered inputs with one-clock delay • tRAS Lock-out function supported • Phase-lock loop (PLL) clock driver to reduce loading • Internal four bank operations with single pulsed RAS • 2.5V +/- 0.2V VDD and VDDQ Power supply • Auto refresh and self refresh supported • All inputs and outputs are compatible with SSTL_2 interface • 8192 refresh cycles / 64ms ORDERING INFORMATION Part No. Power Supply HYMD512G726B(L)4-M HYMD512G726B(L)4-K HYMD512G726B(L)4-H HYMD512G726B(L)4-L Clock Frequency Interface Form Factor SSTL_2 184pin Registered DIMM 5.25 x 1.2 x 0.15 inch 133MHz (*DDR266 2-2-2) VDD=2.5V VDDQ=2.5V 133MHz (*DDR266A) 133MHz (*DDR266B) 125MHz (*DDR200) * JEDEC Defined Specifications compliant This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 0.1 / June 2004 1 HYMD512G726B(L)4M-M/K/H/L PIN DESCRIPTION Pin Pin Description Pin CK0, /CK0 Differential Clock Inputs VDDQ Pin Description DQs Power Supply CS0 Chip Select Input VSS Ground CKE0 Clock Enable Input VREF Reference Power Supply /RAS, /CAS, /WE Commend Sets Inputs VDDSPD Power Supply for SPD A0 ~ A12 Address SA0~SA2 E2PROM Address Inputs BA0, BA1 Bank Address SCL E2PROM Clock DQ0~DQ63 Data Inputs/Outputs SDA E2PROM Data I/O CB0~CB7 Data Strobe Inputs/Outputs WP Write Protect Flag DQS0~DQS17 Data Strobe Inputs/Outputs VDDID VDD Identification Flag DM0~7 Data-in Mask DU Do not Use VDD Power Supply NC No Connection /RESET Reset Enable FETEN FET Enable PIN ASSIGNMENT Pin Name Pin Name Pin Name Pin Name Pin Name Pin 1 VREF 32 A5 62 VDDQ 93 VSS 124 VSS 154 Name /RAS 2 DQ0 33 DQ24 63 /WE 94 DQ4 125 A6 155 DQ45 VDDQ 3 VSS 34 VSS 64 DQ41 95 DQ5 126 DQ28 156 4 DQ1 35 DQ25 65 /CAS 96 VDDQ 127 DQ29 157 /CS0 5 DQS0 36 DQS3 66 VSS 97 DQS9 128 VDDQ 158 /CS1* 6 DQ2 37 A4 67 DQS5 98 DQ6 129 DQS12 159 DM5 7 VDD 38 VDD 68 DQ42 99 DQ7 130 A3 160 VSS 8 DQ3 39 DQ26 69 DQ43 100 VSS 131 DQ30 161 DQ46 DQ47 9 NC 40 DQ27 70 VDD 101 NC 132 VSS 162 10 /RESET 41 A2 71 NC 102 NC 133 DQ31 163 NC 11 VSS 42 Vss 72 DQ48 103 A13 134 CB4 164 VDDQ 12 DQ8 43 A1 73 DQ49 104 VDDQ 135 CB5 165 DQ52 13 DQ9 44 CB0 74 VSS 105 DQ12 136 VDDQ 166 DQ53 14 DQS1 45 CB1 75 DU 106 DQ13 137 CK0 167 NC, FETEN* 15 VDDQ 46 VDD 76 DU 107 DQS10 138 /CK0 168 VDD 16 DU 47 DQS8 77 VDDQ 108 VDD 139 VSS 169 DM6 17 DU 48 A0 78 DQS6 109 DQ14 140 DQS17 170 DQ54 18 VSS 49 CB2 79 DQ50 110 DQ15 141 A10 171 DQ55 19 DQ10 50 VSS 80 DQ51 111 CKE1* 142 CB6 172 VDDQ 20 DQ11 51 CB3 81 VSS 112 VDDQ 143 VDDQ 173 NC 21 CKE0 52 BA1 82 VDDID 113 BA2* 144 CB7 174 DQ60 22 VDDQ 83 DQ56 114 DQ20 175 DQ61 23 DQ16 53 DQ32 84 DQ57 115 A12 145 VSS 176 VSS 24 DQ17 54 VDDQ 85 VDD 116 VSS 146 DQ36 177 DM7 25 DQS2 55 DQ33 86 DQS7 117 DQ21 147 DQ37 178 DQ62 26 VSS 56 DQS4 87 DQ58 118 A11 148 VDD 179 DQ63 27 A9 57 DQ34 88 DQ59 119 DQS11 149 DQS13 180 VDDQ 28 DQ18 58 VSS 89 VSS 120 VDD 150 DQ38 181 SA0 29 A7 59 BA0 90 WP 121 DQ22 151 DQ39 182 SA1 30 VDDQ 60 DQ35 91 SDA 122 A8 152 VSS 183 SA2 31 DQ19 61 DQ40 92 SCL 123 DQ23 153 DQ44 184 VDDSPD Key key * These are not used on this module but may be used for other module in 184pin DIMM family Rev. 0.1 / June 2004 2 HYMD512G726B(L)4M-M/K/H/L FUNCTIONAL BLOCK DIAGRAM VSS /RS0 DQS0 DM0/DQS9 DQ0 DQ1 DQ2 DQ3 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ8 DQ9 DQ10 DQ11 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ16 DQ17 DQ18 DQ19 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ24 DQ25 DQ26 DQ27 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ32 DQ33 DQ34 DQ35 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ40 DQ41 DQ42 DQ43 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ48 DQ49 DQ50 DQ51 DQS I/O0 I/O1 I/O2 I/O3 /CS DM D0 DQS1 DQ4 DQ5 DQ6 DQ7 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ12 DQ13 DQ14 DQ15 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ20 DQ21 DQ22 DQ23 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ28 DQ29 DQ30 DQ31 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ36 DQ37 DQ38 DQ39 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ44 DQ45 DQ46 DQ47 DQS I/O0 I/O1 I/O2 I/O3 /CS DQ52 DQ53 DQ54 DQ55 DQS I/O0 I/O1 I/O2 I/O3 /CS DM D0 D9 DM1/DQS10 DM D1 DQS2 DM D0 D10 DM2/DQS11 DM D2 DQS3 DM D0 D11 DM3/DQS12 DM D3 DQS4 DM D0 D12 DM4/DQS13 DM D4 DQS5 DM D0 D13 DM5/DQS14 DM D5 DQS6 DM D0 D14 DM6/DQS15 DM D6 DQS7 D0 D15 DM7/DQS16 DQS I/O0 I/O1 I/O2 I/O3 DQ56 DQ57 DQ58 DQ59 /CS DM DQ60 DQ61 DQ62 DQ63 D7 DQS8 DQS I/O0 I/O1 I/O2 I/O3 /CS DM DQS I/O0 I/O1 I/O2 I/O3 /S0 R E G I S T E R BA0-BA1 A0-A12 /RAS /CAS CKE /W E PCK /PCK /CS DM D8 CB4 CB5 CB6 CB7 /RS->/CS : SDRAMs D0-D17 RBA0-RBA1-> : BA0->BA1 : SDRAMs D0-D17 RA0-RA12-> : A0->A12 : SDRAMs D0-D17 /RRAS->/RAS : SDRAMs D0-D17 /RCAS->/CAS : SDRAMs D0-D17 RCKEA->CKE : SDRAMs D0-D17 /RW E->W E : SDRAMs D0-D17 DQS I/O0 I/O1 I/O2 I/O3 VDDQ DO-D8 VDD DO-D8 VREF DO-D8 VSS DO-D8 Strap:see Note 4 VDDID D0 D16 Serial PD DM8/DQS17 CB0 CB1 CB2 CB3 Serial PD VDDSPD DM /CS D0 D17 DM SCL SDA WP A0 A1 A2 SA0 SA1 SA2 Note : 1. DQ-to-I/O wiring may be changed within a byte. 2. DQ/DQS/DM/CKE/S relationships must be maintained as shown. 3. DQ/DQS resistors should be 22 Ohms. 4. V DDID strap connections (for memory device V DD , V DDQ ) : STRAP OUT (OPEN) : V DD = V DDQ STRAP IN (V SS ) : V DD ≠ V DDQ 5. Address and control resistors should be 22 Ohms. /RESET CKO, /CKO------PLL* * W ire per Clock Loading Table /W iring Diagram Rev. 0.1 / June 2004 3 HYMD512G726B(L)4M-M/K/H/L ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit Operating Temperature (Ambient) TA 0 ~ +70 o C Storage Temperature TSTG -55 ~ +125 o C Voltage on Any Pin relative to VSS VIN, VOUT -0.5 ~ 3.6 V Voltage on VDD relative to VSS VDD -0.5 ~ 3.6 V Voltage on VDDQ relative to VSS VDDQ -0.5 ~ 3.6 V Output Short Circuit Current IOS 50 mA Power Dissipation PD 1.0 x # of Components W Soldering Temperature Þ Time TSOLDER 260 / 10 oC / Sec Note : Operation at above absolute maximum rating can adversely affect device reliability DC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS= 0V) Parameter Symbol Min Typ. Max Unit Power Supply Voltage VDD 2.3 2.5 2.7 V Power Supply Voltage VDDQ 2.3 2.5 2.7 V Input High Voltage VIH VREF + 0.15 - VDDQ + 0.3 V Input Low Voltage VIL -0.3 - VREF - 0.15 V Termination Voltage VTT VREF - 0.04 VREF VREF + 0.04 V Reference Voltage VREF 0.49*VDDQ 0.5*VDDQ 0.51*VDDQ V Note 1 2 3 Note : 1. VDDQ must not exceed the level of VDD. 2. VIL (min) is acceptable -1.5V AC pulse width with < 5ns of duration. 3. The value of VREF is approximately equal to 0.5VDDQ. AC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS = 0V) Parameter Symbol Input High (Logic 1) Voltage, DQ, DQS and DM signals VIH(AC) Input Low (Logic 0) Voltage, DQ, DQS and DM signals VIL(AC) Input Differential Voltage, CK and /CK inputs VID(AC) Input Crossing Point Voltage, CK and /CK inputs VIX(AC) Min Max VREF + 0.31 Unit Note V VREF - 0.31 V 0.7 VDDQ + 0.6 V 1 0.5*VDDQ-0.2 0.5*VDDQ+0.2 V 2 Note : 1. VID is the magnitude of the difference between the input level on CK and the input on /CK. 2. The value of VIX is expected to equal 0.5*V DDQ of the transmitting device and must track variations in the DC level of the same. Rev. 0.1 / June 2004 4 HYMD512G726B(L)4M-M/K/H/L AC OPERATING TEST CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V) Parameter Value Unit Reference Voltage VDDQ x 0.5 V Termination Voltage VDDQ x 0.5 V AC Input High Level Voltage (VIH, min) VREF + 0.31 V AC Input Low Level Voltage (VIL, max) VREF - 0.31 V Input Timing Measurement Reference Level Voltage VREF V Output Timing Measurement Reference Level Voltage VTT V Input Signal maximum peak swing 1.5 V Input minimum Signal Slew Rate 1 V/ns Termination Resistor (RT) 50 Ω Series Resistor (RS) 25 Ω Output Load Capacitance for Access Time Measurement (CL) 30 pF Rev. 0.1 / June 2004 5 HYMD512G726B(L)4M-M/K/H/L CAPACITANCE (TA=25oC, f=100MHz ) Parameter Pin Symbol Min Max Unit Input Capacitance A0 ~ A12, BA0, BA1 CIN1 8 12 pF Input Capacitance /RAS, /CAS, /WE CIN2 8 12 pF Input Capacitance CKE0 CIN3 8 12 pF Input Capacitance CS0 CIN4 8 12 pF Input Capacitance CK0, /CK0 CIN5 8 14 pF Data Input / Output Capacitance DQ0 ~ DQ63, DQS0 ~ DQS17 CIO1 7 12 pF Data Input / Output Capacitance CB0 ~ CB7 CIO2 7 12 pF Note : 1. VDD = min. to max., VDDQ = 2.3V to 2.7V, VODC = VDDQ/2, VOpeak-to-peak = 0.2V 2. Pins not under test are tied to GND. 3. These values are guaranteed by design and are tested on a sample basis only. OUTPUT LOAD CIRCUIT V TT R T =50Ω Output Zo=50Ω V REF C L=30pF Rev. 0.1 / June 2004 6 HYMD512G726B(L)4M-M/K/H/L DC CHARACTERISTICS I (TA=0 to 70oC, Voltage referenced to VSS = 0V) Parameter Input Leakage Current Add, CMD, /CS, /CKE Symbol Min. Max -2 2 -4 4 ILI CK, /CK Unit Note uA 1 Output Leakage Current ILO -5 5 uA 2 Output High Voltage VOH VTT + 0.76 - V IOH = -15.2mA Output Low Voltage VOL - VTT - 0.76 V IOL = +15.2mA Note : 1. VIN = 0 to 3.6V, All other pins are not tested under VIN =0V 2. DOUT is disabled, VOUT=0 to 2.7V 3. These values are device characteristics. Rev. 0.1 / June 2004 7 HYMD512G726B(L)4M-M/K/H/L DC CHARACTERISTICS II (TA=0 to 70oC, Voltage referenced to VSS = 0V) Bin Sort :M(DDR266(2-2-2),K(DDR266A@CL=2) H(DDR266B@CL=2.5),L(DDR200@CL=2) Parameter Symbol Speed Test Condition -M -K -H -L Unit Note Operating Current IDD0 One bank; Active - Precharge ; tRC=tRC(min); tCK= tCK(min) ; DQ,DM and DQS inputs changing twice per clock cycle ; address and control inputs changing once per clock cycle Operating Current IDD1 One bank ; Active - Read - Precharge ; Burst Length = 2 ; tRC=tRC(min); tCK= tCK(min) ; address and control inputs changing once per clock cycle Precharge Power Down Standby Current IDD2P All banks idle ; Power down mode ; CKE= Low, tCK= tCK(min) 830 mA Idle Standby Current IDD2F /CS = High, All banks idle ; tCK= tCK(min) ; CKE = High ; address and control inputs changing once per clock cycle. VIN = VREF for DQ, DQS and DM 1280 mA Active Power Down Standby Current IDD3P One bank active ; Power down mode ; CKE= Low, tCK= tCK(min) 866 mA Active Standby Current IDD3N /CS= HIGH; CKE = HIGH; One bank; ActivePrecharge; tRC = tRAS(max); tCK = t CK (max); DQ, DM and DQS inputs changing twice per clock cycle; Address and other control inputs changing once per clock cycle 1370 mA Operating Current IDD4R Burst = 2 ; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK= tCK (min); IOUT = 0mA 4250 3710 mA IDD4W Burst = 2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK (min); DQ, DM, and DQS inputs changing twice per clock cycle 4250 3710 mA 5030 4670 mA Operating Current Auto Refresh Current IDD5 tRC = tRFC(min) - 8*tCK for DDR200 at 100Mhz, 10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh Self Refresh Current IDD6 CKE =< 0.2V; External clock on; tCK = tCK(min) Operating Current Four Bank Operation IDD7 Four bank interleaving with BL=4 Refer to the following page for detailed test condition Rev. 0.1 / June 2004 2990 2810 2450 mA 3530 3350 3170 mA Normal 440 mA Low Power 395 mA 7490 6050 mA 8 HYMD512G726B(L)4M-M/K/H/L AC CHARACTERISTICS (AC operating conditions unless otherwise noted) Bin Sort :M(DDR266(2-2-2),K(DDR266A@CL=2) H(DDR266B@CL=2.5),L(DDR200@CL=2) -M Parameter -K H -L Symbol Unit Min Max Min Max Min Max Min Max Row Cycle Time tRC 60 - 65 - 65 - 70 - ns Auto Refresh Row Cycle Time tRFC 75 - 75 - 75 - 80 - ns Row Active Time tRAS 45 120K 45 120K 45 120K 50 120K ns Active to Read with Auto Precharge Delay tRAP tRCD or tRPmin - tRCD or tRPmin - tRCD or tRPmin - tRCD or tRPmin - ns Row Address to Column Address Delay tRCD 15 - 20 - 20 - 20 - ns Row Active to Row Active Delay tRRD 15 - 15 - 15 - 15 - ns Column Address to Column Address Delay tCCD 1 - 1 - 1 - 1 - CK Row Precharge Time tRP 15 - 20 - 20 - 20 - ns Write Recovery Time tWR 15 - 15 - 15 - 15 - ns Write to Read Command Delay tWTR 1 - 1 - 1 - 1 - CK Auto Precharge Write Recovery + Precharge Time tDAL (tWR/ tCK) + (tRP/tCK) - (tWR/tCK) + (tRP/tCK) (tWR/tCK) + (tRP/tCK) - (tWR/tCK) + (tRP/tCK) 7.5 12 7.5 12 7.5 12 8 12 7.5 12 10 12 10 12 10 12 System Clock Cycle Time CL = 2.5 CL = 2 tCK CK Note 16 15 ns Clock High Level Width tCH 0.45 0.55 0.45 0.55 0.45 0.55 0.45 0.55 CK Clock Low Level Width tCL 0.45 0.55 0.45 0.55 0.45 0.55 0.45 0.55 CK Data-Out edge to Clock edge Skew tAC -0.7 0.7 -0.7 0.7 -0.7 0.7 -0.7 0.7 ns DQS-Out edge to Clock edge Skew tDQSCK -0.7 0.7 -0.7 0.7 -0.7 0.7 -0.7 0.7 ns DQS-Out edge to Data-Out edge Skew tDQSQ - 0.5 0.5 - 0.5 0.6 ns Data-Out hold time from DQS tQH tHP -tQHS - tHP -tQHS - tHP -tQHS - tHP -tQHS - ns 1, 10 Clock Half Period tHP min (tCL,tCH) - min (tCL,tCH) - min (tCL,tCH) - min (tCL,tCH) - ns 1,9 tQHS - 0.75 - 0.75 - 0.75 - 0.75 ns 10 Data-out high-impedance window from CK, /CK tHZ -0.75 0.75 -0.75 0.75 -0.75 0.75 -0.8 0.8 ns 17 Data-out low-impedance window from CK, /CK tLZ -0.75 0.75 -0.75 0.75 -0.75 0.75 -0.8 0.8 ns 17 Input Setup Time (fast slew rate) tIS 0.9 - 0.9 - 0.9 - 1.1 - ns 2,3,5,6 Input Hold Time (fast slew rate) tIH 0.9 - 0.9 - 0.9 - 1.1 - ns 2,3,5,6 Data Hold Skew Factor Rev. 0.1 / June 2004 9 HYMD512G726B(L)4M-M/K/H/L AC CHARACTERISTICS (AC operating conditions unless otherwise noted) - continued - Bin Sort :M(DDR266(2-2-2),K(DDR266A@CL=2) H(DDR266B@CL=2.5),L(DDR200@CL=2) -M Parameter -K H -L Symbol Min Max Min Max Min Max Min Max Unit Note Input Setup Time (slow slew rate) tIS 1.0 - 1.0 - 1.0 - 1.1 - ns 2,4,5,6 Input Hold Time (slow slew rate) tIH 1.0 - 1.0 - 1.0 - 1.1 - ns 2,4,5,6 tIPW 2.2 - 2.2 - 2.2 - 2.5 - ns 6 Write DQS High Level Width tDQSH 0.35 - 0.35 - 0.35 - 0.35 - CK Write DQS Low Level Width tDQSL 0.35 - 0.35 - 0.35 - 0.35 - CK Clock to First Rising edge of DQS-In tDQSS 0.75 1.28 0.75 1.25 0.75 1.25 0.75 1.25 CK Data-In Setup Time to DQS-In (DQ & DM) tDS 0.5 0.5 0.5 0.6 ns Data-in Hold Time to DQS-In (DQ & DM) tDH 0.5 0.5 0.5 0.6 ns DQ & DM Input Pulse Width tDIPW 1.75 1.75 1.75 2 ns Read DQS Preamble Time tRPRE 0.9 1.1 0.9 1.1 0.9 1.1 0.9 1.1 CK Read DQS Postamble Time tRPST 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 CK Write DQS Preamble Setup Time tWPRES 0 0 0 0 CK Write DQS Preamble Hold Time tWPREH 0.25 0.25 0.25 0.25 CK Write DQS Postamble Time tWPST 0.4 Mode Register Set Delay tMRD 2 2 2 2 CK tXSC 200 200 200 200 CK Input Pulse Width Exit self refresh to Any Executable Command Average Periodic Refresh Interval 0.6 tREFI 7.8 0.4 0.6 7.8 0.4 0.6 7.8 0.4 0.6 7.8 6,7,11~ 13 6 CK 8 us Note : 1. This calculation accounts for tDQSQ(max), the pulse width distortion of on-chip circuit and jitter. 2. Data sampled at the rising edges of the clock : A0~A12, BA0~BA1, CKE, /CS, /RAS, /CAS, /WE. 3. For command/address input slew rate >=1.0V/ns 4. For command/address input slew rate >=0.5V/ns and <1.0V/ns This derating table is used to increase tIS/tIH in case where the input slew-rate is below 0.5V/ns. Input Setup / Hold Slew-rate Derating Table. Input Setup / Hold Slew-rate Delta tIS Delta tIH V/ns ps ps 0.5 0 0 0.4 +50 0 0.3 +100 0 5. CK, /CK slew rates are >=1.0V/ns 6. These parameters guarantee device timing, but they are not necessarily tested on each device, and they may be guaranteed by design or tester correlation 7. Data latched at both rising and falling edges of Data Strobes(LDQS/UDQS) : DQ, LDM/UDM. Rev. 0.1 / June 2004 10 HYMD512G726B(L)4M-M/K/H/L 8. Minimum of 200 cycles of stable input clocks after Self Refresh Exit command, where CKE is held high, is required to complete Self Refresh Exit and lock the internal DLL circuit of DDR SDRAM 9. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH). 10. tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL). tQHS consists of tDQSQmax, the pulse width distortion of on-chip clock circuits, data pin to pin skew and output pattern effects and p-channel to n-channel variation of the output drivers. 11.This derating table is used to increase tDS/tDH in case where the input slew-rate is below 0.5V/ns. Input Setup / Hold Slew-rate Derating Table. Input Setup / Hold Slew-rate Delta tDS Delta tDH V/ns ps ps 0.5 0 0 0.4 +75 +75 0.3 +150 +150 12. I/O Setup/Hold Plateau Derating. This derating table is used to increase tDS/tDH in case where the input level is flat below VREF +/-310mV for a duration of up to 2ns. I/O Input Level Delta tDS Delta tDH mV ps ps +280 +50 +50 13. I/O Setup/Hold Delta Inverse Slew Rate Derating. This derating table is used to increase tDS/tDH in case where the DQ and DQS slew rates differ. The Delta Inverse Slew Rate is calculated as (1/SlewRate1)-(1/SlewRate2). For example, if slew rate 1 = 0.5V/ns and Slew Rate2 = 0.4V/n then the Delta Inverse Slew Rate = -0.5ns/V. (1/SlewRate1)-(1/SlewRate2) Delta tDS Delta tDH ns/V ps ps 0 0 0 +/-0.25 +50 +50 +/- 0.5 +100 +100 14. DQS, DM and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi tions through the DC region must be monotonic. 15. tDAL = (tDPL / tCK ) + (tRP / tCK ). For each of the terms above, if not already an integer, round to the next highest integer. tCK is equal to the actual system clock cycle time. Example: For DDR266B at CL=2.5 and tCK = 7.5 ns, tDAL = (15 ns / 7.5 ns) + (20 ns / 7.5 ns) = (2.00) + (2.67) Round up each non-integer to the next highest integer: = (2) + (3), tDAL = 5 clock 16. For the parts which do not has internal RAS lockout circuit, Active to Read with Auto precharge delay should be tRAS - BL/2 x tCK2. Rev. 0.1 / June 2004 11 HYMD512G726B(L)4M-M/K/H/L SIMPLIFIED COMMAND TRUTH TABLE A10/ AP Command CKEn-1 CKEn /CS /RAS /CAS /WE Extended Mode Register Set H X L L L L OP code 1,2 Mode Register Set H X L L L L OP code 1,2 H X X X H X X 1 L H H H Device Deselect No Operation Bank Active H X L L H H H X L H L H ADDR RA Read BA V L CA Read with Autoprecharge 1 1,3 L H X L H L L CA Write with Autoprecharge 1 V H Precharge All Banks H X L L H L Precharge selected Bank 1 V H Write Note 1,4 H X 1,5 L V 1 X Read Burst Stop H X L H H L X 1 Auto Refresh H H L L L H X 1 Entry H L L L L H H X X X Exit L H L H H H H X X X L H H H Self Refresh Precharge Power Down Mode Active Power Down Mode Entry H 1 X 1 1 L 1 X Exit Entry Exit L H L H X X X 1 L H H H 1 H X X X 1 L V V V H L H X X 1 1 ( H=Logic High Level, L=Logic Low Level, X=Don’t Care, V=Valid Data Input, OP Code=Operand Code, NOP=No Operation ) Note : 1. DM states are Don’t Care. Refer to below Write Mask Truth Table. 2. OP Code(Operand Code) consists of A0~A12 and BA0~BA1 used for Mode Registering duing Extended MRS or MRS. Before entering Mode Register Set mode, all banks must be in a precharge state and MRS command can be issued after tRP period from Prechagre command. 3. If a Read with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented to activated bank until CK(n+BL/2+tRP). 4. If a Write with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented to activated bank until CK(n+BL/2+1+tDPL+tRP). Last Data-In to Prechage delay(tDPL) which is also called Write Recovery Time (tWR) is needed to guarantee that the last data has been completely written. 5. If A10/AP is High when Row Precharge command being issued, BA0/BA1 are ignored and all banks are selected to be precharged. Rev. 0.1 / June 2004 12 HYMD512G726B(L)4M-M/K/H/L PACKAGE DIMENSIONS Front 133.35 5.25 Register 30.48 1.2 PLL Back Side 3.99 .157max (Front) Register 1.27+/-0.10 0.05+/-0.004 Rev. 0.1 / June 2004 13 SERIAL PRESENCE DETECT SPD SPECIFICATION (128Mx72 Registered DDR DIMM) Rev. 0.1 / June 2004 14 HYMD512G726B(L)4M-M/K/H/L SERIAL PRESENCE DETECT Byte Function Description 0 Number of Bytes written into serial memory at module manufacturer 1 Total number of Bytes in SPD device 2 Fundamental memory type 3 4 5 Function Supported -M -K Hexa Value -H -L -M 128 Bytes -K -H -L Note 80h 256 Bytes 08h DDR SDRAM 07h Number of row address on this assembly 13 0Dh 1 Number of column address on this assembly 12 0Ch 1 Number of physical banks on DIMM 1Bank 01h 6 Module data width 72 Bits 48h 7 Module data width (continued) - 00h 8 Module voltage Interface levels(VDDQ) 9 DDR SDRAM cycle time at CAS Latency=2.5(tCK) 10 DDR SDRAM access time from clock at CL=2.5 (tAC) +/-0.75ns +/-0.75ns +/-0.75ns 11 Module configuration type 12 Refresh rate and type 13 SSTL 2.5V 7.5ns 7.5ns 04h 7.5ns 8ns 75h 75h 75h 80h 2 +/-0.8ns 75h 75h 75h 80h 2 ECC 02h 7.8us & Self refresh 82h Primary DDR SDRAM width x4 04h 14 Error checking DDR SDRAM data width x4 04h 15 Minimum clock delay for back-to-back random column address(tCCD) 1 CLK 01h 2,4,8 0Eh 16 Burst lengths supported 17 Number of banks on each DDR SDRAM 18 CAS latency supported 4 Banks 04h 2, 2.5 0Ch 19 CS latency 0 01h 20 WE latency 1 02h 21 DDR SDRAM module attributes Registered, PLL 26h +/-0.2Voltage tolerance, Concurrent Auto Precharge tRAS Lock Out C0h 22 DDR SDRAM device attributes : General 23 DDR SDRAM cycle time at CL=2.0(tCK) 24 DDR SDRAM access time from clock at CL=2.0(tAC) 7.5ns 7.5ns 10ns +/-0.75ns +/-0.75ns +/-0.75ns 10ns 75h 75h A0h A0h 2 +/-0.8ns 75h 75h 75h 80h 2 25 DDR SDRAM cycle time at CL=1.5(tCK) - 00h 2 26 DDR SDRAM access time from clock at CL=1.5(tAC) - 00h 2 27 Minimum row precharge time(tRP) 15ns 20ns 20ns 20ns 3Ch 50h 50h 50h 28 Minimum row activate to row active delay(tRRD) 15ns 15ns 15ns 15ns 3Ch 3Ch 3Ch 3Ch 29 Minimum RAS to CAS delay(tRCD) 15ns 20ns 20ns 20ns 3Ch 50h 50h 50h 30 Minimum active to precharge time(tRAS) 45ns 45ns 45ns 50ns 2Dh 2Dh 2Dh 32h 31 Module row density 32 Command and address signal input setup time(tIS) 0.9ns 0.9ns 0.9ns 1.1ns 90h 90h 90h B0h 33 Command and address signal input hold time(tIH) 0.9ns 0.9ns 0.9ns 1.1ns 90h 90h 90h B0h 34 Data signal input setup time(tDS) 0.5ns 0.5ns 0.5ns 0.6ns 50h 50h 50h 60h 35 Data signal input hold time(tDH) 0.5ns 0.5ns 0.5ns 0.6ns 50h 50h 50h 60h 1GB 36~40 Reserved for VCSDRAM 01h Undefined 00h 41 Minimum active / auto-refresh time ( tRC) 60ns 65ns 65ns 70ns 3Ch 41h 41h 46h 42 Minimum auto-refresh to active/auto-refresh command period(tRFC) 75ns 75ns 75ns 80ns 4Bh 4Bh 4Bh 50h 43 Maximum cycle time (tCK max) 12ns 12ns 12ns 12ns 30h 30h 30h 30h 44 Maximim DQS-DQ skew time(tDQSQ) 0.5ns 0.5ns 0.5ns 0.6ns 32h 32h 32h 3Ch 45 Maximum read data hold skew factor(tQHS) 0.75ns 0.75ns 0.75ns 0.75ns 75h 75h 75h 75h B5h 4Fh 46~61 Superset information(may be used in future) 62 SPD Revision code 63 Checksum for Bytes 0~62 Rev. 0.1 / June 2004 Undefined 00h Initial release - 00h 5Dh 8Ah 15 HYMD512G726B(L)4M-M/K/H/L SERIAL PRESENCE DETECT Byte 64 65~71 72 Function Description Function Supported -M Manufacturer JEDEC ID Code -K -L -M -K -H Hynix JEDEC ID ADh - 00h Hynix(Korea Area) HSA(United States Area) HSE(Europe Area) HSJ(Japan Area) Singapore Asia Area 0*h 1*h 2*h 3*h 4*h 5*h --------- Manufacturer JEDEC ID Code Manufacturing location -H Hexa Value 73 Manufacture part number(Hynix Memory Module) H 48h 74 -------- Manufacture part number(Hynix Memory Module) Y 59h 75 -------- Manufacture part number(Hynix Memory Module) M 4Dh 76 Manufacture part number (DDR SDRAM) D 44h 77 Manufacture part number(Memory density) 5 35h 78 Manufacture part number(Module Depth) 1 31h 79 ------- Manufacture part number(Module Depth) 2 32h 80 Manufacture part number(Module type) G 47h 81 Manufacture part number(Data width) 7 37h 82 -------Manufacture part number(Data width) 2 32h 83 Manufacture part number(Refresh, # of Bank.) 84 Manufacture part number(Component Generation) 6(8K refresh,4Bank) 36h B 42h 85 Manufacture part number(Component configuration) 4 34h 86 Manufacture part number(Low profile) M 4Dh 87 Manufacture part number(Hyphen) 88 Manufacture part number(Minimum cycle time) 89~90 M K Manufacture part number(T.B.D) -L Note 6 2Dh H L 4Dh 4Bh 48h Blank 20h - 4Ch 91 Manufacture revision code(for Component) - 92 Manufacture revision code (for PCB) - - 93 Manufacturing date(Year) - - 94 Manufacturing date(Week) - - 3 95~98 Module serial number - - 4 99~127 Manufacturer specific data (may be used in future) 128~255 Open for customer use 3 Undefined 00h 5 Undefined 00h 5 Note : 1. The bank address is excluded 2. This value is based on the component specification 3. These bytes are programmed by code of date week & date year 4. These bytes apply to Hynix’s own Module Serial Number System 5. These bytes undefined and coded as ‘00h’ 6. Refer to Hynix Web Site Byte 85~87, Low Power Part Byte # Function Description 85 86 87 Manufacture part number(Low power part) Manufacture part number(Component Configuration) Manufacture part number(Low profile) Rev. 0.1 / June 2004 Function Supported -M -K -H L 4 M Hexa Value -L -M -K -H -L Note 4Ch 34h 4Dh 16