IDT74ALVCH162344 3.3V CMOS 1-BIT TO 4-BIT ADDRESS DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE IDT74ALVCH162344 3.3V CMOS 1-BIT TO 4-BIT ADDRESS DRIVER WITH 3-STATE OUTPUTS AND BUS-HOLD FEATURES: DESCRIPTION: • 0.5 MICRON CMOS Technology • Typical tSK(o) (Output Skew) < 250ps • ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) • VCC = 3.3V ± 0.3V, Normal Range • VCC = 2.7V to 3.6V, Extended Range • VCC = 2.5V ± 0.2V µ W typ. static) • CMOS power levels (0.4µ • Rail-to-Rail output swing for increased noise margin • Available in SSOP, TSSOP, and TVSOP packages This 1-bit to 4-bit address driver is built using advanced dual metal CMOS technology. The ALVCH162344 device is used in applications in which four separate memory locations must be addressed by a single address. The ALVCH162344 has series resistors in the device output structure which will significantly reduce line noise when used with light loads. This driver has been designed to drive ±12mA at the designated threshold levels. The ALVCH162344 has “bus-hold” which retains the inputs’ last state whenever the input goes to a high-impedance. This prevents floating inputs and eliminates the need for pull-up/down resistors. DRIVE FEATURES: APPLICATIONS: • Balanced Output Drivers: ±12mA • Low switching noise • 3.3V high speed systems • 3.3V and lower voltage computing systems FUNCTIONAL BLOCK DIAGRAM OE 1 1 OE 3 2 1A 5A 9 2A 5B 4 41 2B 1 37 2B 4 6B 4 OE 4 7A 23 7B 1 43 44 3B 4 7B 4 55 4B 1 21 8A 27 56 48 3B 1 15 20 6B 1 42 28 16 4A 30 6A OE 2 5B 1 36 1B 4 14 13 3A 34 1B 1 8 6 29 49 51 4B 4 8B 1 8B 4 The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE MARCH 1999 1 © 1999 Integrated Device Technology, Inc. DSC-4563/1 IDT74ALVCH162344 3.3V CMOS 1-BIT TO 4-BIT ADDRESS DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol Description VTERM(2) Max Unit Terminal Voltage with Respect to GND –0.5 to +4.6 V OE 1 1 56 OE 4 VTERM(3) Terminal Voltage with Respect to GND –0.5 to VCC+0.5 V 1B1 2 55 8B 1 TSTG Storage Temperature –65 to +150 °C 1B2 3 54 8B 2 –50 to +50 mA ±50 mA IOUT DC Output Current IIK Continuous Clamp Current, VI < 0 or VI > VCC GND 4 53 GND 1B 3 5 52 8B 3 IOK Continuous Clamp Current, VO < 0 –50 mA 1B 4 6 51 8B 4 mA 7 50 V CC Continuous Current through each VCC or GND ±100 V CC ICC ISS 1A 8 49 8A 2B 1 9 48 7B 1 2B2 10 47 7B 2 GND 11 46 GND 2B 3 12 45 7B 3 2B 4 13 44 7B 4 2A 14 43 7A 3A 15 42 6A 3B 1 16 41 6B1 3B2 17 40 GND 18 3B 3 CAPACITANCE (TA = +25°C, F = 1.0MHz) Parameter(1) Conditions Typ. Max. Unit CIN Input Capacitance VIN = 0V 5 7 pF 6B2 COUT Output Capacitance VOUT = 0V 7 9 pF 39 GND CI/O I/O Port Capacitance VIN = 0V 7 9 pF 19 38 6B 3 3B 4 20 37 6B 4 4A 21 36 5A V CC 22 35 V CC 4B1 23 34 5B 1 4B 2 24 33 5B 2 GND 25 32 GND 4B3 26 31 5B 3 4B 4 27 30 5B4 28 29 OE 2 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VCC terminals. 3. All terminals except VCC. Symbol NOTE: 1. As applicable to the device type. PIN DESCRIPTION Pin Names OEx Description 3-State Output Enable Inputs (Active LOW) xA Data Inputs(1) xBx 3-State Outputs NOTE: 1. These pins have "Bus-Hold". All other pins are standard inputs, outputs, or I/Os. OE 3 FUNCTION TABLE(1) SSOP/ TSSOP/ TVSOP TOP VIEW Inputs OEx xA xBx L L L L H H H X Z NOTE: 1. H = HIGH Voltage Level X = Don’t Care L = LOW Voltage Level Z = High-Impedance 2 Outputs IDT74ALVCH162344 3.3V CMOS 1-BIT TO 4-BIT ADDRESS DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Operating Condition: TA = –40°C to +85°C Symbol VIH VIL Min. Typ.(1) Max. Unit VCC = 2.3V to 2.7V 1.7 — — V VCC = 2.7V to 3.6V 2 — — VCC = 2.3V to 2.7V — — 0.7 VCC = 2.7V to 3.6V — — 0.8 Parameter Input HIGH Voltage Level Input LOW Voltage Level Test Conditions V IIH Input HIGH Current VCC = 3.6V VI = VCC — — ±5 µA IIL Input LOW Current VCC = 3.6V VI = GND — — ±5 µA IOZH High Impedance Output Current VCC = 3.6V VO = VCC — — ±10 µA IOZL (3-State Output pins) VO = GND — — ±10 VIK Clamp Diode Voltage VCC = 2.3V, IIN = –18mA — –0.7 –1.2 V VH ICCL ICCH ICCZ ∆ICC Input Hysteresis Quiescent Power Supply Current VCC = 3.3V VCC = 3.6V VIN = GND or VCC — — 100 0.1 — 40 mV µA Quiescent Power Supply Current Variation One input at VCC - 0.6V, other inputs at VCC or GND — — 750 µA Min. Typ.(2) Max. Unit – 75 — — µA VI = 0.8V 75 — — VI = 1.7V – 45 — — VI = 0.7V 45 — — — ±500 NOTE: 1. Typical values are at VCC = 3.3V, +25°C ambient. BUS-HOLD CHARACTERISTICS Symbol IBHH Parameter(1) Bus-Hold Input Sustain Current Test Conditions VCC = 3V VI = 2V IBHL IBHH Bus-Hold Input Sustain Current VCC = 2.3V IBHL IBHHO Bus-Hold Input Overdrive Current VCC = 3.6V VI = 0 to 3.6V IBHLO NOTES: 1. Pins with Bus-Hold are identified in the pin description. 2. Typical values are at VCC = 3.3V, +25°C ambient. 3 — µA µA IDT74ALVCH162344 3.3V CMOS 1-BIT TO 4-BIT ADDRESS DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE OUTPUT DRIVE CHARACTERISTICS Symbol VOH VOL Test Conditions(1) Parameter Output HIGH Voltage Output LOW Voltage Min. Max. Unit VCC – 0.2 — V IOH = – 4mA 1.9 — VCC = 2.3V to 3.6V IOH = – 0.1mA VCC = 2.3V IOH = – 6mA 1.7 — VCC = 2.7V IOH = – 4mA 2.2 — IOH = – 8mA 2 — VCC = 3V IOH = – 6mA 2.4 — IOH = – 12mA 2 — VCC = 2.3V to 3.6V IOL = 0.1mA — 0.2 VCC = 2.3V IOL = 4mA — 0.4 IOL = 6mA — 0.55 VCC = 2.7V IOL = 4mA — 0.4 IOL = 8mA — 0.6 IOL = 6mA — 0.55 IOL = 12mA — 0.8 VCC = 3V V NOTE: 1. VIH and VIL must be within the min. or max. range shown in the DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE table for the appropriate VCC range. TA = – 40°C to + 85°C. OPERATING CHARACTERISTICS, TA = 25°C Symbol Parameter CPD Power Dissipation Capacitance Outputs enabled CPD Power Dissipation Capacitance Outputs disabled VCC = 2.5V ± 0.2V VCC = 3.3V ± 0.3V Test Conditions Typical Typical Unit CL = 0pF, f = 10Mhz 68 82 pF 12 14 SWITCHING CHARACTERISTICS(1) VCC = 2.5V ± 0.2V Symbol Parameter VCC = 2.7V VCC = 3.3V ± 0.3V Min. Max. Min. Max. Min. Max. Unit 1 4.9 — 5.1 1.4 4.4 ns 1 6.4 — 6.6 1.2 5.7 ns 1 5.4 — 4.7 1.2 4.5 ns tPLH Propagation Delay tPHL xA to xBx tPZH Output Enable Time tPZL OE to xBx tPHZ Output Disable Time tPLZ OE to xBx tSK(O) Output Skew(2) — — — — — 500 ps tSK(b) Output Skew(2) — — — — — 350 ps NOTES: 1. See TEST CIRCUITS AND WAVEFORMS. TA = – 40°C to + 85°C. 2. Skew between any two outputs of the same package and switching in the same direction. For tSK(O), OUTPUT1 and OUTPUT2 are any two outputs. For tSK(b), OUTPUT1 and OUTPUT2 are in the same bank of the same package; this parameter is guaranteed but not production tested. 4 IDT74ALVCH162344 3.3V CMOS 1-BIT TO 4-BIT ADDRESS DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS VCC(1)= 3.3V±0.3V VCC(1)= 2.7V Symbol VCC(2)= 2.5V±0.2V Unit VLOAD 6 6 2 x Vcc V VIH 2.7 2.7 Vcc V VT 1.5 1.5 Vcc / 2 V VLZ 300 300 150 mV VHZ 300 300 150 mV CL 50 50 30 pF (1, 2) tPHL V IH VT 0V ALVC Link DISABLE ENABLE CONTROL INPUT GND tPZL D.U.T. OUTPUT SW ITCH NORMALLY CLOSED LOW tPZH OUTPUT SW ITCH NORMALLY OPEN HIGH 500 Ω RT tPLH V OH VT V OL Propagation Delay V OUT Pulse Generator tPHL OPPOSITE PHASE INPUT TRANSITION Open 500 Ω tPLH OUTPUT V LOAD V CC V IN V IH VT 0V SAME PHASE INPUT TRANSITION CL ALVC Link Test Circuit for All Outputs tPLZ V IH VT 0V V LOAD/2 V LOAD/2 VT V LZ V OL tPHZ VT V OH V HZ 0V 0V ALVC Link DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. Enable and Disable Times NOTE: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. V IH DATA VT INPUT 0V tSU tH V IH TIMING VT INPUT 0V tREM V IH ASYNCHRONOUS VT CONTROL 0V V IH SYNCHRONOUS VT CONTROL tSU 0V tH NOTES: 1. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2ns; tR ≤ 2ns. SWITCH POSITION Test Switch Open Drain Disable Low Enable Low VLOAD Disable High Enable High GND All Other Tests Open ALVC Link V IH INPUT tPHL1 tPLH1 Set-up, Hold, and Release Times VT 0V V OH OUTPUT 1 tSK (x) LOW-HIGH-LOW PULSE VT V OL tSK (x) tW V OH VT V OL OUTPUT 2 VT HIGH-LOW -HIGH PULSE VT ALVC Link tPLH2 tPHL2 Pulse Width tSK (x) = tPLH2 - tPLH1 or tPHL2 - tPHL1 Output Skew - tSK(X) ALVC Link NOTES: 1. For tSK(o) OUTPUT1 and OUTPUT2 are any two outputs. 2. For tSK(b) OUTPUT1 and OUTPUT2 are in the same bank. 5 IDT74ALVCH162344 3.3V CMOS 1-BIT TO 4-BIT ADDRESS DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION ID T XX X XX XX X XX Bus-Hold Fam ily D evice Type Package ALV C Tem p. R ange CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 PV PA PF Shrink Sm all Outline P ackage Thin Shrink Sm all Outline P ackage Thin Very Sm all Outline P ackage 344 1-B it to 4-B it Address D river w ith 3-S tate Outputs 162 D ouble-Density with Resistors, ±12m A H Bus-Hold 74 –40°C to +85°C for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 6 for Tech Support: [email protected] (408) 654-6459