TECHNICAL DATA IL386 Low Voltage Audio Power AMP The IL386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value up to 200. The inputs are ground referenced while the output is automatically biased to one half the supply voltage. The quiescent power drain is only 24 milliwatts when operating from a 6 volt supply, making the IL386 ideal for battery operation. • Battery Operation • Minimum External Parts • Wide Supply Voltage Range: 4 V - 12 V • Low Quiescent Current Drain: 4 mA • Voltage Gains from 20 to 200 • Ground Referenced Input • Self-Centering Output Quiescent Voltage • Low Distortion • Eight Pin Dual-In-Line Package ORDERING INFORMATION IL386N Plastic IL386D SOIC TA = 0° to 70° C for package PIN ASSIGNMENT LOGIC DIAGRAM Pin 4 = GND Pin 6 = Supply Voltage V+ 1 IL386 MAXIMUM RATINGS* Symbol Parameter Value Unit 15 V VCC Supply Voltage VIN Input Voltage ±0.4 V PD Power Dissipation 1.25 W Tstg Storage Temperature -65 to +150 °C TJ Junction Temperature +150 °C TL Lead Temperature +300 °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage TA Operating Temperature, All Package Types Min Max Unit 4.0 12 V 0 +70 °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. ELECTRICAL CHARACTERISTICS(TA = 25°C) Symbol Parameter Test Conditions Guaranteed Limits Min V + I+ Quiescent Current 4 V+ = 6 V, VIN = 0 + PO Output Power V = 6V, RL =8Ω, THD=10% V+= 9V, RL =8Ω, THD=10% AV Voltage Gain V+= 6V, f=1kHz 10µF from Pin 1 and 8 BW Bandwidth V+= 6V, Pins 1 and 8 Open THD Total Harmonic Distortion V+= 6V, RL =8Ω, POUT=125mW, f=1kHz, Pins 1 and 8 Open PSRR Power Supply Rejection Ratio V+= 6V, f=1kHz, CBYPASS=10µF, Pins 1 and 8 Open RIN IB 2 Operating Supply Voltage Input Resistance Input Bias Current Typ V = 6V, Pins 2 and 3 Open Max 12 V 8 mA 325 1000 mW 26 46 dB 250 KHz 1.0 45 30 + Unit dB 80 250 % KΩ nA IL34119 APPLICATION INFORMATION GAIN CONTROL To make the IL386 a more versatile amplifier, two pins (1 and 8) are provided for gain control. With pins 1 and 8 open the 1.35 KΩ resistor sets the gain at 20 (26 dB). If a capacitor is put from pin 1 to 8, bypassing the 1.35 KΩ resistor, the gain will go up to 200 (46 dB). If a resistor is placed in series with the capacitor, the gain can be set to any value from 20 to 200. Gain control can also be done by capacitively coupling a resistor (or FET) from pin 1 to ground. Additional external components can be placed in parallel with the internal feedback resistors to tailor the gain and frequency response for individual applications. For example, we can compensate poor speaker bass response by frequency shaping the feeback path. This is done with a series RC from pin 1 to 5 (paralleling the internal 15 KΩ resistor). For 6 dB effective bass boots: R≅15 KΩ, the lowest value for good stable operation is R=10 KΩ if pin 8 is open. If pins 1 and 8 are bypassed then R as low as 2 KΩ can be used. This restriction is because the amplifier is only compensated for closed-loop gains greater the 9. INPUT BIASING The schematic shows that both inputs are biased to ground with a 50 KΩ resistor. The base current of the input transistors is about 250 nA, so the inputs are at at out 12.5 mV when left open. If the dc source resistance oriving the IL386 is higher than 250 KΩ it will contribute very little additional offset (about 2.5 mV at the input, 50 mV at the output). If the dc source resistance is less than 10 KΩ, then shorting the unused input to ground will keep the offset low (about 2.5 mV at the input, 50 mV at the output). For dc source resistances between these values we can eliminate excess offset by putting a resistor from the unesed input to ground, equal in value to the dc source resistance. Of course all affset problems are eliminated if the input is capacitively coupled. When using the IL386 with higher gains (by pessing the 1.35 KΩ resistor between pins 1 and 8) it is necessary to bypass the unused input, preventing degradation of gain and possible instabilities. This is done with a 0.1 µF capacitor or a short to ground depending on the dc source resistance on the driven input. SCHEMATIC DIAGRAM 3