TECHNICAL DATA Telephone Tone Ringer with Bridge Diode IL6840 The IL6840 is a monolithic integrated circuit telephone tone ringer with bridge diode, when coupled with an appropriate transducer, it replaces the electro-mechanical bell. The device is designed for use with either a piezo transducer or an inexpensive transformer coupled speaker to produce a pleasing tone composed of a high frequency (fR) alternating with a low frequency (fL) resulting in a warble frequency. The supply voltage is obtained from the AC ring signal and the circuit is designed so that noise on the line or variation of the ringing signal can not affect correct operation of the device. • On chip high voltage full wave diode bridge rectifier • Low current consumption, in order to allow the parallel operation of the 4 devices • Low external component count • Tone and switching frequencies adjustable by external components • High noise immunity due to built-in voltage-current hysteresis • Activation voltage adjustable • Internal zener diodes to protect against over voltages • Ringer impedance adjustable with external components ORDERING INFORMATION IL6840N Plastic DIP IL6840D SOIC TA = -40° to 70° C for package PIN ASSIGNMENT OUT BLOCK DIAGRAM 1 IL6840 MAXIMUM RATINGS* (TA = 25°C) Symbol Parameter Value Unit VTP Calling Voltage (f = 50 Hz) Continuous 120 Vrms VTP Calling Voltage (f = 50 Hz) 5 Sec ON/10 Sec OFF 200 Vrms ICC Supply Current 22 mA Tstg Storage and Junction Temperature -60 to +125 °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage TA Operating Temperature Min -40 Max Unit 26 V +70 °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. ELECTRICAL CHARACTERISTICS (TA = 25°C) Symbol Parameter ICC Current Consumption without Load VON Activiation Voltage VONR Activiation Voltage Range VSUS Sustaining Voltage Test Conditions Guaranteed Limits Min VS=8.8 to 26 V RA = 1 KΩ Max Unit 1.8 mA 12.2 13 V 8 10 V 8 8.8 V Differential Resistance in Off Condition VTIP = 8.0 V VRING = 0 V 6.4 3500 KΩ VOUT Output Voltage Swing VS = 26 V, VSRC = 8.0 V, VOFR = 8.0 V 21 25.5 V IOUT Short Circuit Current VS = 26 V 30 80 mA RD 2 IL6840 AC CHARACTERISTICS Symbol Parameter fH1 fH2 fL Guaranteed Limits Test Conditions Output Frequencies fH1 fH2 VCC = 26 V, R1 = 14 KΩ VSCR = 0 V V SCR = 6 V fH Range max VCC = 26 V, R1 = 1.7 KΩ, VSCR = 0 V fH Range min VCC = 26 V, R1 = 27 KΩ, VSCR = 6.0 V Sweep Frequency VCC = 26 V, C1 = 100 nF Min Max 1960 1420 2570 1840 14 Unit Hz Hz KHz 7.0 0.11 KHz 13.0 Hz TEST AND APPLICATION CIRCUIT Figure1 : Single output applied pin#5 1 F, 250V AC 0.22 F 2.2 K TIP R2 C2 10K 8 TEL 5 IL6840 7 C3 10 F 6 1 2 3 10K Piezo 4 VOUT 1300:8 RING C1 100nF R1 14K VS f1 = 3.22 •104 / R1 (KΩ); f2 = 5/7 f1; fsweep = 1000 / C1(nF) 3 IL6840 Figure2 : Single output applied pin#6 1 F, 250V AC 0.22 F 2.2 K TIP R2 C2 10K 8 TEL 5 IL6840 7 C3 10 F 6 1 2 3 10K Piezo 4 VOUT 1300:8 RING C1 100nF R1 14K VS f1 = 3.22 •104 / R1 (KΩ); f2 = 5/7 f1; fsweep = 1000 / C1(nF) DESCRIPTION The IL6840 tone ringer derives its power supply by rectifying the AC ringing signal. It uses this power to activate two tone generators. The two tone frequencies generated are switched by internal oscillator in a fast sequence and made audible across an output amplifier in the loudspeaker; both tone frequencies and the switching frequency can be externally adjusted. The device can drive either directly a piezo ceramic converter (buzzer) or small loudspeaker. In case of using a loud-speaker, a transformer is needed. An internal shunt voltage regulator provides DC voltage to the output stage, low frequency oscillator, and high frequency oscillator. To protect the IC from telephone line transients, a zener Diode is included. 4 IL6840 N SUFFIX PLASTIC DIP (MS – 001BA) A Dimension, mm 5 8 B 1 4 MIN MAX A 8.51 10.16 B 6.10 7.11 5.33 C L F Symbol C D 0.36 0.56 F 1.14 1.78 -T- SEATING PLANE N G M K 0.25 (0.010) M J H D T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.20 0.36 N 0.38 D SUFFIX SOIC (MS - 012AA) Dimension, mm A 8 5 B H 1 G P 4 D K MIN MAX A 4.80 5.00 B 3.80 4.00 C 1.35 1.75 D 0.33 0.51 F 0.40 1.27 R x 45 C -T- Symbol SEATING PLANE J F 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. M G 1.27 H 5.72 J 0° 8° K 0.10 0.25 M 0.19 0.25 P 5.80 6.20 R 0.25 0.50 5