ISL83220E TM Data Sheet September 2001 +/-15kV ESD Protected, +3V to +5.5V, 1Microamp, 250kbps, RS-232 Transmitters/Receivers itle L32 E, L32 E, L32 E, L32 E, L32 E, L32 E) bt kV D ted, V to .5V, icro p, 0kbp S2 nsts/Re v) utho ) eyrds File Number 6011.1 Features • ESD Protection for RS-232 I/O Pins to ±15kV (IEC1000) • Drop in Replacement for SP3220E The Intersil ISL83220E is a 3.0V to 5.5V powered RS-232 transmitter/receiver which meets ElA/TIA-232 and V.28/V.24 specifications, even at VCC = 3.0V. Additionally, it provides ±15kV ESD protection (IEC 1000-4-2 Air Gap and Human Body Model) on transmitter outputs and receiver inputs (RS-232 pins). Targeted applications are PDAs, Palmtops, and notebook and laptop computers where the low operational, and even lower standby, power consumption is critical. Efficient on-chip charge pumps, coupled with a manual powerdown function, reduce the standby supply current to a 1µA trickle. Small footprint packaging, and the use of small, low value capacitors ensure board space savings as well. Data rates greater than 250kbps are guaranteed at worst case load conditions. This family is fully compatible with 3.3V only systems, mixed 3.3V and 5.0V systems, and 5.0V only systems. Table 1 summarizes the features of the ISL83320E, while Application Note AN9863 summarizes the features of each device comprising the ICL32XXE 3V family. • Meets EIA/TIA-232 and V.28/V.24 Specifications at 3V • Interoperable with RS-232 down to VCC = 2.7V • Latch-Up Free • On-Chip Voltage Converters Require Only Four External 0.1µF Capacitors • Manual Powerdown Feature with Receivers Active • Separate Receiver Enable Pin • RX and TX Hysteresis For Improved Noise Immunity • Guaranteed Minimum Data Rate . . . . . . . . . . . . . 250kbps • Guaranteed Minimum Slew Rate . . . . . . . . . . . . . . . 6V/µs • Wide Power Supply Range . . . . . . . Single +3V to +5.5V • Low Supply Current in Powerdown State. . . . . . . . . . . 1µA Applications • Any System Requiring RS-232 Communication Ports - Battery Powered, Hand-Held, and Portable Equipment - Laptop Computers, Notebooks, Palmtops - Modems, Printers and other Peripherals - Digital Cameras - Cellular/Mobile Phones Related Literature • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” TABLE 1. SUMMARY OF FEATURES PART NUMBER ISL83220E NO. OF NO. OF Tx. Rx. 1 1 1 NO. OF MONITOR Rx. (R OUTB) DATA RATE (kbps) Rx. ENABLE FUNCTION? READY OUTPUT? MANUAL POWERDOWN? AUTOMATIC POWERDOWN FUNCTION? 0 250 YES NO YES NO CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc. | Copyright © Intersil Americas Inc. 2001 ISL83220E Ordering Information (NOTE 1) PART NO. TEMP. RANGE ( oC) Pinout PACKAGE ISL83220E (SOIC, SSOP, TSSOP) TOP VIEW PKG. NO. ISL83220ECB 0 to 70 16 Ld SOIC M16.3 EN 1 ISL83220EIB -40 to 85 16 Ld SOIC M16.3 C1+ 2 15 VCC V+ 3 14 GND ISL83220ECA 0 to 70 ISL83220EIA -40 to 85 ISL83220ECV ISL83220EIV 16 Ld SSOP M16.209 16 Ld SSOP M16.209 0 to 70 16 Ld TSSOP M16.173 -40 to 85 16 Ld TSSOP M16.173 16 SHDN C1- 4 13 T1OUT C2+ 5 12 N.C. C2- 6 11 T1IN V- 7 10 N.C. R1IN 8 NOTE: 9 R1OUT 1. Most surface mount devices are available on tape and reel; add “-T” to suffix. Pin Descriptions PIN VCC FUNCTION System power supply input (3.0V to 5.5V). V+ Internally generated positive transmitter supply (+5.5V). V- Internally generated negative transmitter supply (-5.5V). GND Ground connection. C1+ External capacitor (voltage doubler) is connected to this lead. C1- External capacitor (voltage doubler) is connected to this lead. C2+ External capacitor (voltage inverter) is connected to this lead. C2- External capacitor (voltage inverter) is connected to this lead. TIN TTL/CMOS compatible transmitter Inputs. TOUT RIN ROUT EN SHDN N.C. ±15kV ESD Protected, RS-232 level (nominally ±5.5V) transmitter outputs. ±15kV ESD Protected, RS-232 compatible receiver inputs. TTL/CMOS level receiver outputs. Active low receiver enable control; doesn’t disable ROUTB outputs. Active low input shuts down transmitters and on-board power supply, to place device in low power mode. No internal connection. Typical Operating Circuit ISL83220E +3.3V C1 0.1µF C2 0.1µF T1IN TTL/CMOS LOGIC LEVELS R1OUT + 0.1µF 2 + C1+ 4 C15 + C2+ 6 C211 15 VCC 3 V+ V- 7 + C3 0.1µF C4 + 0.1µF T1 13 9 8 T1OUT R1 IN 5kΩ R1 1 EN 16 GND 14 2 SHDN VCC RS-232 LEVELS ISL83220E Absolute Maximum Ratings Thermal Information VCC to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V V+ to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3V to -7V V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14V Input Voltages TIN, EN, SHDN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V RIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25V Output Voltages TOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±13.2V ROUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V CC +0.3V Short Circuit Duration TOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . See Specification Table Thermal Resistance (Typical, Note 2) θJA (oC/W) 16 Ld Wide SOIC Package . . . . . . . . . . . . . . . . . . . 100 16 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . . 135 16 Ld TSSOP Package . . . . . . . . . . . . . . . . . . . . . . 145 Moisture Sensitivity (see Technical Brief TB363) All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1 Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (Lead Tips Only) Operating Conditions Temperature Range ISL83220ECX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC ISL83220EIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 2. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications Test Conditions: VCC = 3V to 5.5V, C1 - C4 = 0.1µF; Unless Otherwise Specified. Typicals are at TA = 25oC PARAMETER TEMP (oC) MIN TYP MAX UNITS 25 - 0.3 1.0 mA 25 - 1.0 10 µA Full - - 0.8 V VCC = 3.3V Full 2.0 - - V VCC = 5.0V Full 2.4 - - V 25 - 0.3 TEST CONDITIONS DC CHARACTERISTICS Supply Current All Outputs Unloaded, SHDN = VCC Supply Current, Powerdown SHDN = GND VCC = 3.15V LOGIC AND TRANSMITTER INPUTS AND RECEIVER OUTPUTS Input Logic Threshold Low TIN, EN, SHDN Input Logic Threshold High TIN, EN, SHDN Transmitter Input Hysteresis V Input Leakage Current TIN, EN, SHDN Full - ±0.01 ±1.0 µA Output Leakage Current EN = VCC Full - ±0.05 ±10 µA Output Voltage Low IOUT = 1.6mA Full - - 0.4 V Output Voltage High IOUT = -1.0mA Full - V Output Voltage Swing All Transmitter Outputs Loaded with 3kΩ to Ground Full ±5.0 ±5.4 - V Output Resistance VCC = V+ = V- = 0V, Transmitter Output = ±2V Full 300 10M - Ω Output Short-Circuit Current VOUT = 0V Full - ±35 ±60 mA Output Leakage Current VOUT = ±12V, VCC = 0V or 3V to 5.5V, SHDN = GND Full - - ±25 µA Full -25 - 25 V VCC = 3.3V Full 0.6 1.2 - V VCC = 5.0V Full 0.8 1.5 - V VCC -0.6 VCC -0.1 TRANSMITTER OUTPUTS RECEIVER INPUTS Input Voltage Range Input Threshold Low 3 ISL83220E Electrical Specifications Test Conditions: VCC = 3V to 5.5V, C1 - C4 = 0.1µF; Unless Otherwise Specified. Typicals are at TA = 25oC (Continued) TEMP (oC) MIN TYP MAX UNITS VCC = 3.3V Full - 1.5 2.4 V VCC = 5.0V Full - 1.8 2.4 V Input Hysteresis 25 - 0.3 - V Input Resistance Full 3 5 7 kΩ Full 250 500 - kbps tPHL 25 - 1.0 - µs tPLH 25 - 1.0 - µs tPHL 25 - 0.20 - µs tPLH PARAMETER TEST CONDITIONS Input Threshold High TIMING CHARACTERISTICS Maximum Data Rate RL = 3kΩ, C L = 1000pF, One Transmitter Switching Transmitter Propagation Delay Transmitter Input to Transmitter Output, RL = 3kΩ, C L = 1000pF Receiver Propagation Delay Receiver Input to Receiver Output, CL = 150pF 25 - 0.30 - µs Receiver Output Enable Time Normal Operation 25 - 200 - ns Receiver Output Disable Time Normal Operation 25 - 200 - ns Transmitter Skew tPHL - tPLH (Note 3) 25 - 100 500 ns Receiver Skew tPHL - tPLH Full - 100 1000 ns Transition Region Slew Rate CL = 150pF to 2500pF VCC = 3.3V, RL = 3kΩ to 7kΩ, CL = 150pF to 1000pF Measured From 3V to -3V or -3V to 3V 25 4 - 30 V/µs 25 6 - 30 V/µs Human Body Model 25 - ±15 - kV ESD PERFORMANCE RS-232 Pins (TOUT, RIN) All Other Pins IEC1000-4-2 Contact Discharge 25 - ±8 - kV IEC1000-4-2 Air Gap Discharge 25 - ±15 - kV Human Body Model 25 - ±3 - kV NOTE: 3. Transmitter skew is measured at the transmitter zero crossing points. Detailed Description Transmitters The ISL83220E operates from a single +3V to +5.5V supply, guarantees a 250kbps minimum data rate, requires only four small external 0.1µF capacitors, features low power consumption, and meets all ElA RS-232C and V.28 specifications. The circuit is divided into three sections: The charge pump, the transmitter, and the receiver. The transmitters are proprietary, low dropout, inverting drivers that translate TTL/CMOS inputs to EIA/TIA-232 output levels. Coupled with the on-chip ±5.5V supplies, these transmitters deliver true RS-232 levels over a wide range of single supply system voltages. Charge-Pump Intersil’s new 3.3V family utilizes regulated on-chip dual charge pumps as voltage doublers, and voltage inverters to generate ±5.5V transmitter supplies from a VCC supply as low as 3.0V. This allows these devices to maintain RS-232 compliant output levels over the ±10% tolerance range of 3.3V powered systems. The efficient on-chip power supplies require only four small, external 0.1µF capacitors for the voltage doubler and inverter functions, even at VCC = 3.3V. The charge pumps operate discontinuously (i.e., they turn off as soon as the V+ and V- supplies are pumped up to the nominal values), resulting in significant power savings. 4 The transmitter output disables and assumes a high impedance state when the device enters the powerdown mode (see Table 2). This output may be driven to ±12V when disabled. All devices guarantee a 250kbps data rate for full load conditions (3kΩ and 1000pF), VCC ≥ 3.0V. Under more typical conditions of VCC ≥ 3.3V, RL = 3kΩ, and CL = 250pF, the ISL83220E easily operates at 900kbps. Transmitter inputs float if left unconnected, and may cause ICC increases. ISL83220E Receivers The ISL83220E device contains a standard inverting receiver that three-states via the EN control line. Receivers convert RS-232 signals to CMOS output levels and accept inputs up to ±25V while presenting the required 3kΩ to 7kΩ input impedance (see Figure 1) even if the power is off (VCC = 0V). The receiver’s Schmitt trigger input stage uses hysteresis to increase noise immunity and decrease errors due to slow input signal transitions. The ISL83220E receiver disables only when EN is driven high. (see Table 2). This allows the receiver to monitor external devices, like a modem, even when the ISL83220E is in its 1µA powerdown state. Standard receivers driving powered down peripherals must be disabled to prevent current flow through the peripheral’s protection diodes (see Figures 2). This renders them useless for wake up functions. section). The time to recover from manual powerdown mode is typically 100µs. TABLE 2. POWERDOWN AND ENABLE LOGIC TRUTH TABLE SHDN EN TRANSMITTER RECEIVER INPUT INPUT OUTPUT OUTPUT L L High-Z Active Manual Powerdown L H High-Z High-Z Manual Powerdown w/Rcvr. Disabled H L Active Active Normal Operation H H Active High-Z Normal Operation w/Rcvr. Disabled VCC VCC VCC R1OUT R1IN -25V ≤ VRIN ≤ +25V MODE OF OPERATION CURRENT FLOW VCC GND ≤ VROUT ≤ VCC 5kΩ VOUT = VCC GND Rx FIGURE 1. INVERTING RECEIVER CONNECTIONS POWERED DOWN UART Operation down to 2.7V ISL83220E transmitter outputs meet RS-562 levels (±3.7V) with VCC as low as 2.7V. RS-562 levels typically ensure inter operability with RS-232 devices. Powerdown Functionality This 3V family of RS-232 interface devices requires a nominal supply current of 0.3mA during normal operation (not in powerdown mode), which is considerably less than the 5mA to 11mA current required of 5V RS-232 devices. The already low current requirement drops significantly when the device enters powerdown mode. In powerdown, supply current drops to 1µA, because the on-chip charge pump turns off (V+ collapses to VCC, V- collapses to GND), and the transmitter outputs three-state. This micro-power mode makes these devices ideal for battery powered and portable applications. Software Controlled (Manual) Powerdown On the ISL83220E, the powerdown control is via a simple shutdown (SHDN) pin. Driving this pin high enables normal operation, while driving it low forces the IC into it’s powerdown state. Connect SHDN to VCC if the powerdown function isn’t needed. Note that the receiver output remains enabled during shutdown (see Table 2). For the lowest power consumption during powerdown, the receiver should also be disabled by driving the EN input high (see next 5 Tx GND SHDN = GND OLD RS-232 CHIP FIGURE 2. POWER DRAIN THROUGH POWERED DOWN PERIPHERAL Receiver ENABLE Control The ISL83220E also features an EN input to control the receiver output. Driving EN high disables the receiver output placing it in a high impedance state. This is useful to eliminate supply current, due to a receiver output forward biasing the protection diode, when driving the input of a powered down (VCC = GND) peripheral (see Figure 2). Capacitor Selection The charge pumps require 0.1µF capacitors for 3.3V operation. Do not use values smaller than 0.1 µF. Increasing the capacitor values (by a factor of 2) reduces ripple on the transmitter outputs and slightly reduces power consumption. When using minimum required capacitor values, make sure that capacitor values do not degrade excessively with temperature. If in doubt, use capacitors with a larger nominal value. The capacitor’s equivalent series resistance (ESR) usually rises at low temperatures and it influences the amount of ripple on V+ and V-. ISL83220E Power Supply Decoupling VCC + 0.1µF In most circumstances a 0.1µF bypass capacitor is adequate. In applications that are particularly sensitive to power supply noise, decouple V CC to ground with a capacitor of the same value as the charge-pump capacitor C1. Connect the bypass capacitor as close as possible to the IC. + C1+ VCC V+ C1 C1- + C3 ISL83220E + Transmitter Output when Exiting Powerdown V- C2+ C2 C4 + C2- Figure 3 shows the response of the transmitter output when exiting powerdown mode. As it activates, the transmitter output properly goes to RS-232 levels, with no glitching, ringing, nor undesirable transients. The transmitter is loaded with 3kΩ in parallel with 2500pF. Note that the transmitter enables only when the magnitude of the supplies exceed approximately 3V. TIN TOUT RIN ROUT 5k EN VCC 1000pF SHDN FIGURE 4. TRANSMITTER LOOPBACK TEST CIRCUIT 5V/DIV. SHDN TIN = LOW 5V/DIV. T1IN 2V/DIV. T1OUT TIN = HIGH VCC = +3.3V C1 - C4 = 0.1µF R1OUT VCC = +3.3V C1 - C4 = 0.1µF TIME (20µs/DIV.) FIGURE 3. TRANSMITTER OUTPUT WHEN EXITING POWERDOWN 5µs/DIV. FIGURE 5. LOOPBACK TEST AT 120kbps High Data Rates The ISL83220E maintains the RS-232 ±5V minimum transmitter output voltages even at high data rates. Figure 4 details a transmitter loopback test circuit, and Figure 5 illustrates the loopback test result at 120kbps. For this test, the transmitter is driving an RS-232 load in parallel with 1000pF, at 120kbps. Figure 6 shows the loopback results for the transmitter driving 1000pF and an RS-232 load at 250kbps. 5V/DIV. T1IN T1OUT R1OUT VCC = +3.3V C1 - C4 = 0.1µF 2µs/DIV. FIGURE 6. LOOPBACK TEST AT 250kbps 6 ISL83220E Interconnection with 3V and 5V Logic The ISL83220E directly interfaces with 5V CMOS and TTL logic families. Nevertheless, with the ISL83220E at 3.3V, and the logic supply at 5V, AC, HC, and CD4000 outputs can drive ISL83220E inputs, but ISL83220E outputs do not reach the minimum V IH for these logic families. See Table 3 for more information. TABLE 3. LOGIC FAMILY COMPATIBILITY WITH VARIOUS SUPPLY VOLTAGES VCC SYSTEM POWER-SUPPLY SUPPLY VOLTAGE VOLTAGE (V) (V) 3.3 3.3 5 5 5 3.3 COMPATIBILITY Compatible with all CMOS families. Compatible with all TTL and CMOS logic families. Compatible with ACT and HCT CMOS, and with TTL. ISL83320E outputs are incompatible with AC, HC, and CD4000 CMOS inputs. ±15kV ESD Protection All pins on ISL8XXX devices include ESD protection structures, but the ISL8XXXE family incorporates advanced structures which allow the RS-232 pins (transmitter outputs and receiver inputs) to survive ESD events up to ±15kV. The RS-232 pins are particularly vulnerable to ESD damage because they typically connect to an exposed port on the exterior of the finished product. Simply touching the port pins, or connecting a cable, can cause an ESD event that might destroy unprotected ICs. These new ESD structures protect the device whether or not it is powered up, protect without allowing any latchup mechanism to activate, and don’t interfere with RS-232 signals as large as ±25V. Human Body Model (HBM) Testing As the name implies, this test method emulates the ESD event delivered to an IC during human handling. The tester delivers the charge through a 1.5kΩ current limiting resistor, making the test less severe than the IEC-1000 test which utilizes a 330Ω limiting resistor. The HBM method determines an ICs ability to withstand the ESD transients typically present during handling and manufacturing. Due to the random nature of these events, each pin is tested with respect to all other pins. The RS-232 pins on “E” family devices can withstand HBM ESD events to ±15kV. IEC1000-4-2 Testing The IEC 1000 test method applies to finished equipment, rather than to an individual IC. Therefore, the pins most likely to suffer an ESD event are those that are exposed to the outside world (the RS-232 pins in this case), and the IC is tested in its typical application configuration (power applied) rather than testing each pin-to-pin combination. The lower 7 current limiting resistor coupled with the larger charge storage capacitor yields a test that is much more severe than the HBM test. The extra ESD protection built into this device’s RS-232 pins allows the design of equipment meeting level 4 criteria without the need for additional board level protection on the RS-232 port. AIR-GAP DISCHARGE TEST METHOD For this test method, a charged probe tip moves toward the IC pin until the voltage arcs to it. The current waveform delivered to the IC pin depends on approach speed, humidity, temperature, etc., so it is difficult to obtain repeatable results. The “E” device RS-232 pins withstand ±15kV air-gap discharges. CONTACT DISCHARGE TEST METHOD During the contact discharge test, the probe contacts the tested pin before the probe tip is energized, thereby eliminating the variables associated with the air-gap discharge. The result is a more repeatable and predictable test, but equipment limits prevent testing devices at voltages higher than ±8kV. All “E” family devices survive ±8kV contact discharges on the RS-232 pins. ISL83220E Typical Performance Curves VCC = 3.3V, TA = 25oC TRANSMITTER OUTPUT VOLTAGE (V) 6 25 VOUT+ 4 SLEW RATE (V/µs) 20 2 TRANSMITTER AT 250kbps 0 -2 15 -SLEW +SLEW 10 VOUT - -4 -6 0 1000 2000 3000 4000 5 5000 0 1000 2000 3000 FIGURE 7. TRANSMITTER OUTPUT VOLTAGE vs LOAD CAPACITANCE 3.5 NO LOAD ALL OUTPUTS STATIC 3.0 SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) 40 250kbps 30 25 20 120kbps 15 10 5000 FIGURE 8. SLEW RATE vs LOAD CAPACITANCE 45 35 4000 LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) 20kbps 2.5 2.0 1.5 1.0 0.5 5 0 0 1000 2000 3000 4000 5000 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) LOAD CAPACITANCE (pF) FIGURE 9. SUPPLY CURRENT vs LOAD CAPACITANCE WHEN TRANSMITTING DATA FIGURE 10. SUPPLY CURRENT vs SUPPLY VOLTAGE Die Characteristics PASSIVATION: DIE DIMENSIONS: 100 mils x 100 mils (2540µm x 2540µm) METALLIZATION: Type: Silox Thickness: 13kÅ TRANSISTOR COUNT: Type: Metal 1: AISi(1%) Thickness: Metal 1: 8kÅ Type: Metal 2: AISi (1%) Thickness: Metal 2: 10kÅ 286 PROCESS: Si Gate CMOS SUBSTRATE POTENTIAL (POWERED UP): GND 8 6.0 ISL83220E Thin Shrink Small Outline Plastic Packages (TSSOP) M16.173 N INDEX AREA E 0.25(0.010) M E1 2 INCHES GAUGE PLANE -B1 16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE B M 3 L 0.05(0.002) -A- SEATING PLANE A D -C- e α A2 A1 b 0.10(0.004) M 0.25 0.010 c 0.10(0.004) C A M B S SYMBOL MIN MAX MIN MAX NOTES A - 0.047 - 1.20 - A1 0.002 0.006 0.05 0.15 - A2 0.031 0.051 0.80 1.05 - b 0.0075 0.0118 0.19 0.30 9 c 0.0035 0.0079 0.09 0.20 - D 0.193 0.201 4.90 5.10 3 E1 0.169 0.177 4.30 4.50 4 e 0.026 BSC E 0.246 L 0.0177 N α NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-153-AB, Issue E. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (Angles in degrees) 9 MILLIMETERS 0.65 BSC 0.256 6.25 0.0295 0.45 16 0o 6.50 0.75 16 8o 0o 6 7 8o Rev. 0 6/98 ISL83220E Small Outline Plastic Packages (SSOP) M16.209 (JEDEC MO-150-AC ISSUE B) 16 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE N INDEX AREA 0.25(0.010) M H B M INCHES E GAUGE PLANE -B1 2 3 L 0.25 0.010 SEATING PLANE -A- A D -C- µα e B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A - 0.078 - 2.00 - A1 0.002 - 0.05 - - A2 0.065 0.072 1.65 1.85 - B 0.009 0.014 0.22 0.38 9 C 0.004 0.009 0.09 0.25 - D 0.233 0.255 5.90 6.50 3 E 0.197 0.220 5.00 5.60 4 e A2 A1 B S 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.20mm (0.0078 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.20mm (0.0078 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “B” does not include dambar protrusion. Allowable dambar protrusion shall be 0.13mm (0.005 inch) total in excess of “B” dimension at maximum material condition. 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 10 0.026 BSC H 0.292 L 0.022 N α NOTES: MILLIMETERS 0.65 BSC 0.322 7.40 0.037 0.55 16 0o - 8.20 0.95 16 8o 0o 6 7 8o Rev. 2 3/95 ISL83220E Small Outline Plastic Packages (SOIC) M16.3 (JEDEC MS-013-AA ISSUE C) N 16 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA 0.25(0.010) M H B M INCHES E -B1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.3977 0.4133 10.10 10.50 3 E 0.2914 0.2992 7.40 7.60 4 e µα B S 0.050 BSC 1.27 BSC - H 0.394 0.419 10.00 10.65 - h 0.010 0.029 0.25 0.75 5 L 0.016 0.050 0.40 N α NOTES: MILLIMETERS 16 0o 1.27 16 8o 0o 6 7 8o Rev. 0 12/93 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation 7585 Irvine Center Drive Suite 100 Irvine, CA 92618 TEL: (949) 341-7000 FAX: (949) 341-7123 Intersil Corporation 2401 Palm Bay Rd. Palm Bay, FL 32905 TEL: (321) 724-7000 FAX: (321) 724-7946 11 EUROPE Intersil Europe Sarl Ave. C - F Ramuz 43 CH-1009 Pully Switzerland TEL: +41 21 7293637 FAX: +41 21 7293684 ASIA Intersil Corporation Unit 1804 18/F Guangdong Water Building 83 Austin Road TST, Kowloon Hong Kong TEL: +852 2723 6339 FAX: +852 2730 1433