Dual 12-Bit, 250/200/125 MSPS JESD204B High Speed Serial Output ADC ISLA222S Features The ISLA222S is a series of low-power, high-performance, dual-channel 12-bit, analog-to-digital converters. Designed with FemtoCharge™ technology on a standard CMOS process, the series supports sampling rates of up to 250MSPS. The ISLA222S is part of a pin-compatible family of 12- and 14-bit dual-channel A/Ds with maximum sample rates ranging from 125MSPS to 250MSPS and shares the same analog core as Intersil's proven ISLA222P series of ADCs. The family minimizes power consumption while providing state-of-the art dynamic performance, offering an optimal performance-vspower trade-off. • JESD204A/B High Speed Data Interface Differentiating the ISLA222S from the ISLA222P is its highly configurable, JESD204B-compliant, high speed serial output link. The link offers data rates up to 4.375Gbps per lane and multiple packing modes. It can be configured to use one, two, or three lanes to transmit the conversion data, allowing for flexibility in the receiver design. The SERDES transmitter also provides deterministic latency and multi-chip time alignment support to satisfy an application's complex synchronization requirements. A serial peripheral interface (SPI) port allows for extensive configurability of the JESD204B transmitter including access to its built-in link and transport-layer test patterns. The SPI port also provides control for numerous additional features including the fine gain and offset adjustments of the two ADC cores as well as the programmable clock divider, enabling 2x and 4x harmonic clocking. The ISLA222S is available in a space-saving 7mmx7mm 48 Ld QFN package. The package features a thermal pad for improved thermal performance and is specified over the full industrial temperature range (-40°C to +85°C). - JESD204A Compliant - JESD204B Device Subclass 0 Compliant - JESD204B Device Subclass 2 Compatible - Up to 3 JESD204 Output Lanes Running up to 4.375Gbps - Highly Configurable JESD204 Transmitter • Multiple Chip Time Alignment and Deterministic Latency Support (JESD204B Device Subclass 2) • SPI Programmable Debugging Features and Test Patterns • 48-pin QFN 7mmx7mm Package Key Specifications • SNR @ 250/200/125MSPS 70.6/71.2/71.7 dBFS fIN = 30MHz 70.3/70.7/70.9 dBFS fIN = 190MHz • SFDR @ 250/200/125MSPS 87/93/95 dBc fIN = 30MHz 84/93/86 dBc fIN = 190MHz • Total Power Consumption: 989mW @ 250MSPS Applications • Radar and Satellite Antenna Array Processing • Broadband Communications and Microwave Receivers • High-Performance Data Acquisition • Communications Test Equipment • High-Speed Medical Imaging Pin-Compatible Family RESOLUTION SPEED (MSPS) PRODUCT AVAILABILITY ISLA224S25 14 250 Now ISLA224S20 14 200 Now ISLA224S12 14 125 Now ISLA222S25 12 250 Now ISLA222S20 12 200 Now ISLA222S12 12 125 Now MODEL FIGURE 1. SERDES DATA EYE AT 4.375Gbps May 1, 2012 FN8302.0 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2012. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. CLKP OVDD OVDD (PLL) SYNC AVDD ISLA222S CLOCK GENERATION CLKN AINP 12-BIT 250MSPS ADC SHA AINN LANE[2:0]P LANE[2:0]N VREF JESD204 TRANSMITTER VCM BINP 12-BIT 250MSPS ADC SHA BINN VREF + – CSB SCLK SDIO SDO OVSS SPI CONTROL RESETN AVSS (PLL) NAPSLP AVSS 1.25V FIGURE 2. BLOCK DIAGRAM Pin Configuration DNC DNC AVDD NAPSLP CLKDIV SDIO SCLK CSB SDO OVDD OVSS OVSS ISLA222S (48 LD QFN) TOP VIEW 48 47 46 45 44 43 42 41 40 39 38 37 VCM 1 36 OVDD AVDD 2 35 OVSS AVSS 3 34 LANE2N BINP 4 33 LANE2P BINN 5 32 OVSS AVSS 6 31 LANE1N AVSS 7 30 LANE1P AINN 8 29 OVSS AINP 9 28 LANE0N AVSS 10 27 LANE0P AVDD 11 DNC 12 2 26 OVSS PAD – Exposed Paddle 13 14 15 16 17 18 19 20 21 22 23 24 RESETN AVDD AVDD CLKP CLKN SYNCP SYNCN DNC OVSS (PLL) OVDD (PLL) OVSS (PLL) OVDD (PLL) 25 OVDD FN8302.0 May 1, 2012 ISLA222S Pin Descriptions PIN NUMBER NAME FUNCTION 2, 11, 14, 15, 46 AVDD 1.8V Analog Supply 12, 20, 47, 48 DNC Do Not Connect 3, 6, 7, 10 AVSS Analog Ground 4, 5 BINP, BINN B-Channel Analog Input Positive, Negative 8, 9 AINN, AINP A-Channel Analog Input Negative, Positive 1 VCM 44 CLKDIV 16, 17 CLKP, CLKN 45 NAPSLP Power Control (Nap, Sleep modes) 13 RESETN Power On Reset (Active Low) 26, 29, 32, 35, 37, 38 OVSS Output Ground 25, 36, 39 OVDD 1.8V Digital Supply Common Mode Output Clock Divider Control Clock Input True, Complement 22, 24 OVDD (PLL) 1.8V Analog Supply for SERDES PLL 21, 23 OVSS (PLL) Analog Ground Supply for SERDES PLL 18, 19 SYNCP, SYNCN 27, 28 LANE0P, LANE0N SERDES Lane 0 30, 31 LANE1P, LANE1N SERDES Lane 1 33, 34 LANE2P, LANE2N SERDES Lane 2 40 SDO SPI Serial Data Output 41 CSB SPI Chip Select (active low) 42 SCLK SPI Clock 43 SDIO SPI Serial Data Input/Output PAD AVSS Exposed Paddle. Analog Ground (connect to AVSS) JESD204 SYNC Input Ordering Information PART NUMBER (Notes 1, 2) PART MARKING TEMP. RANGE (°C) PACKAGE (Pb-free) PKG. DWG. # ISLA222S25IR1Z ISLA222S25 IR1Z -40 to +85 48 Ld QFN L48.7x7G ISLA222S20IR1Z ISLA222S20 IR1Z -40 to +85 48 Ld QFN L48.7x7G ISLA222S12IR1Z ISLA222S12 IR1Z -40 to +85 48 Ld QFN L48.7x7G Coming Soon ISLA224S25IR48EV1Z FMC Based Evaluation Board (Supports 125/200/250 speed grades), Dual 14bit Evaluation Board which can be configured for 12bit operation; Interfaces with ADCMB-HSFMC-EV1Z Motherboard and Other FPGA Vendor FMC Based Evaluation Platforms. Coming Soon ADCMB-HSFMC-EV1Z FMC Based Motherboard NOTES: 1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate-e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2. For Moisture Sensitivity Level (MSL), please see device information page for ISLA222S12, ISLA222S20, ISLA222S25. For more information on MSL please see techbrief TB363. 3 FN8302.0 May 1, 2012 ISLA222S Table of Contents Pin Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 JESD204 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Initial Lane Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Test Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Serial Peripheral Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Typical Performance Curves . . . . . . . . . . . . . . . . . . . . . . . . . 10 SPI Physical Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Device Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Device Configuration/Control . . . . . . . . . . . . . . . . . . . . . . . . . Global Device Configuration/Control . . . . . . . . . . . . . . . . . . . ADDRESS 0xDF - 0xF3: JESD204 REGISTERS. . . . . . . . . . . . Address 0xDF-0xEE: JESD204 Parameter INTERFACE. . . . . Theory of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 SPI Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . 5 Digital Specifications.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Switching Specifications.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Power-On Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 User Initiated Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Temperature Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 26 26 27 27 28 29 29 Equivalent Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 ADC Evaluation Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Layout Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Clock Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Jitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Nap/Sleep. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Clock Divider Synchronous Reset . . . . . . . . . . . . . . . . . . . . .20 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Soft Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 4 Split Ground and Power Planes . . . . . . . . . . . . . . . . . . . . . . . Clock Input Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . Exposed Paddle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bypass and Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CML Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unused Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 37 37 37 37 37 Package Outline Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 FN8302.0 May 1, 2012 ISLA222S Absolute Maximum Ratings Thermal Information AVDD to AVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.4V to 2.1V OVDD to OVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.4V to 2.1V AVSS to OVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 0.3V Analog Inputs to AVSS . . . . . . . . . . . . . . . . . . . . . . . . . -0.4V to AVDD + 0.3V Clock Inputs to AVSS . . . . . . . . . . . . . . . . . . . . . . . . . . -0.4V to AVDD + 0.3V Logic Input to AVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.4V to OVDD + 0.3V Logic Inputs to OVSS . . . . . . . . . . . . . . . . . . . . . . . . . . -0.4V to OVDD + 0.3V Latchup (Tested per JESD-78C;Class 2,Level A) . . . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) 48 Ld QFN (Notes 3, 4, 5) . . . . . . . . . . . . . . 24 0.4 Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C NOTES: 3. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 4. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. 5. For solder stencil layout and reflow guidelines, please see Tech Brief TB389. CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. Electrical Specifications All specifications apply under the following conditions unless otherwise noted: AVDD = 1.8V, OVDD = 1.8V, TA = -40°C to +85°C (typical specifications at +25°C), AIN = -2dBFS, fSAMPLE = Maximum Conversion Rate (per speed grade). Boldface limits apply over the operating temperature range, -40°C to +85°C. ISLA222S25 PARAMETER SYMBOL CONDITIONS MIN (Note 6) TYP 1.9 2.00 ISLA222S20 ISLA222S12 MAX MIN MAX MIN MAX (Note 6) (Note 6) TYP (Note 6) (Note 6) TYP (Note 6) UNITS DC SPECIFICATIONS Analog Input Full-Scale Analog Input Range VFS Differential 2.1 1.9 2.0 2.1 1.9 2.0 2.1 VP-P Input Resistance RIN Differential 600 600 600 Ω Input Capacitance CIN Differential 7.4 7.4 7.4 pF Full Temp 115 58 58 ppm/°C Full Scale Range Temp. Drift AVTC Input Offset Voltage VOS ±1 ±1 ±1 mV Gain Error EG 1 1 1 % Common-Mode Output Voltage VCM 0.94 0.94 0.94 V Common Mode Input Current (per pin) ICM 6.0 6.0 6.0 µA/MSPS Inputs Common Mode Voltage 0.9 0.9 0.9 V CLKP, CLKN Swing 1.8 1.8 1.8 V Clock Inputs Power Requirements 1.8V Analog Supply Voltage AVDD 1.8 1.8 1.8 V 1.8V Digital Supply Voltage OVDD 1.8 1.8 1.8 V 1.8V Analog Supply Current IAVDD 353 397 324 365 282 316 mA 1.8V Digital Supply Current IOVDD 195 218 179 200 123 173 mA Minimum number of lanes active 5 FN8302.0 May 1, 2012 ISLA222S Electrical Specifications All specifications apply under the following conditions unless otherwise noted: AVDD = 1.8V, OVDD = 1.8V, TA = -40°C to +85°C (typical specifications at +25°C), AIN = -2dBFS, fSAMPLE = Maximum Conversion Rate (per speed grade). Boldface limits apply over the operating temperature range, -40°C to +85°C. (Continued) ISLA222S25 PARAMETER SYMBOL Power Supply Rejection Ratio (Note 7) PSRR CONDITIONS MIN (Note 6) TYP ISLA222S20 ISLA222S12 MAX MIN MAX MIN MAX (Note 6) (Note 6) TYP (Note 6) (Note 6) TYP (Note 6) UNITS 30MHz 200mVp-p 40 40 40 dB 1MHz 200mVp-p 47 47 47 dB Total Power Dissipation Normal Mode PD 989 1107 910 1017 731 843 mW Nap Mode PD 422 484 391 450 290 398 mW Sleep Mode PD CSB at logic high 6 12 6 12 6 12 mW Nap Mode Wakeup Time Sample Clock Running 5 5 5 µs Sleep Mode Wakeup Time Sample Clock Running 1 1 1 ms -1.0 ±0.1 LSB -1.0 0.5 AC SPECIFICATIONS (Note 8) Differential Nonlinearity DNL Integral Nonlinearity INL Minimum Conversion Rate (Note 9) fS MIN fIN=105MHz No Missing Codes -1.0 ±0.15 -1.5 0.8 1.5 -1.0 ±0.1 -1.0 0.4 100 ISLA222S25/20 (3 Lanes, Efficient Packing) 1.0 100 50 1.0 LSB MSPS ISLA222S12 (2 Lanes, Simple Packing) Maximum Conversion Rate fS MAX Efficient Packing 250 200 125 MSPS Simple Packing Minimum Serdes Lane Data Rate Independent of Packing Mode Maximum Serdes Lane Data Rate Independent of Packing Mode MSPS 1.0 3.75 4.375 1.0 3.0 4.375 3.75 1.0 GBPS 4.375 GBPS 71.7 dBFS 71.5 dBFS (See “Lane data rate” on page 22.) Signal-to-Noise Ratio (Note 10) SNR fIN = 30MHz fIN = 105MHz 6 70.6 69.4 70.6 71.2 70.3 71.1 70.7 fIN = 190MHz 70.3 70.7 70.9 dBFS fIN = 363MHz 69.4 69.5 69.3 dBFS fIN = 495MHz 68.6 68.5 68.0 dBFS fIN = 605MHz 67.9 67.6 66.9 dBFS FN8302.0 May 1, 2012 ISLA222S Electrical Specifications All specifications apply under the following conditions unless otherwise noted: AVDD = 1.8V, OVDD = 1.8V, TA = -40°C to +85°C (typical specifications at +25°C), AIN = -2dBFS, fSAMPLE = Maximum Conversion Rate (per speed grade). Boldface limits apply over the operating temperature range, -40°C to +85°C. (Continued) ISLA222S25 PARAMETER Signal-to-Noise and Distortion (Note 10) Effective Number of Bits (Note 10) Spurious-Free Dynamic Range (Note 10) Spurious-Free Dynamic Range Excluding H2, H3 (Note 10) Intermodulation Distortion SYMBOL SINAD CONDITIONS MIN (Note 6) fIN = 30MHz fIN = 105MHz ENOB SFDR 70.4 71.1 70.2 71.0 70.4 UNITS 71.7 dBFS 71.3 dBFS 70.0 70.5 70.7 dBFS fIN = 363MHz 69.0 68.9 67.8 dBFS fIN = 495MHz 65.4 64.0 61.4 dBFS fIN = 605MHz 59.3 58.0 54.1 dBFS fIN = 30MHz 11.42 11.52 11.61 Bits fIN = 105MHz 11.17 11.40 11.37 11.50 11.40 11.55 Bits fIN = 190MHz 11.34 11.42 11.46 Bits fIN = 363MHz 11.16 11.16 10.97 Bits fIN = 495MHz 10.57 10.34 9.91 Bits fIN = 605MHz 9.56 9.35 8.69 Bits fIN = 30MHz 87 93 95 dBc 87 dBc 74 83 76 89 76 fIN = 190MHz 84 93 86 dBc fIN = 363MHz 79 88 71 dBc fIN = 495MHz 66 85 61 dBc fIN = 605MHz 58 83 52 dBc 87 93 98 dBc fIN = 105MHz 89 95 96 dBc fIN = 190MHz 88 93 90 dBc fIN = 363MHz 84 88 85 dBc fIN = 495MHz 85 85 82 dBc fIN = 605MHz 88 83 81 dBc fIN = 70MHz -84 -82 -81 dBFS fIN = 170MHz -92 -99 -100 dBFS fIN = 10MHz 88 90 100 dB fIN = 124MHz 82 87 86 dB 10-13 10-13 675 675 SFDRX23 fIN = 30MHz Channel-to-Channel Isolation MAX MIN MAX MIN MAX (Note 6) (Note 6) TYP (Note 6) (Note 6) TYP (Note 6) 70.5 69.0 ISLA222S12 fIN = 190MHz fIN = 105MHz IMD TYP ISLA222S20 Word Error Rate WER 10-13 Full Power Bandwidth FPBW 675 MHz NOTES: 6. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 7. PSRR is calculated by the equation 20*log10(A/B), where B is the amplitude of a disturber sinusoid on AVDD at the device pins, and A is the amplitude of the spur in the captured data at the frequency of the disturber sinusoid. 8. AC Specifications apply after internal calibration of the ADC is invoked at the given sample rate and temperature. Refer to “Power-On Calibration” on page 15 and “User Initiated Reset” on page 16 for more detail. 9. The DLL Range setting must be changed via SPI for ADC core sample rates below 80MSPS. The JESD204 transmitter can support ADC sample rates below 100MSPS, as long as the SERDES lane data rate is greater than or equal to 1Gbps. 10. Minimum specification guaranteed when calibrated at +85°C. 7 FN8302.0 May 1, 2012 ISLA222S Digital Specifications Boldface limits apply over the operating temperature range, -40°C to +85°C. PARAMETER SYMBOL CONDITIONS MIN (Note 6) TYP MAX (Note 6) UNITS CMOS INPUTS Input Current High (RESETN) IIH VIN = 1.8V 1 10 µA Input Current Low (RESETN) IIL VIN = 0V -12 -7 µA Input Current High (SDIO, SCL, SDA SCLK) IIH VIN = 1.8V 4 12 µA Input Current Low (SDIO, SCL, SDA SCLK) IIL VIN = 0V -600 -400 -300 µA Input Current High (CSB) IIH VIN = 1.8V 40 52 70 µA Input Current Low (CSB) IIL VIN = 0V 1 10 µA Input Voltage High (SDIO, RESETN) VIH Input Voltage Low (SDIO, RESETN) VIL Input Current High (NAPSLP, CLKDIV) (Note 11) IIH 19 Input Current Low (NAPSLP, CLKDIV) IIL --30 Input Capacitance CDI -25 1.17 V 0.63 V 25 30 µA -25 -19 µA 4 pF LVDS INPUTS (SYNCP, SYNCN) Input Common Mode Range VICM 825 1575 mV Input Differential Swing (peak-to-peak, single-ended) VID 250 450 mV Input Pull-up and Pull-down Resistance RIpu 100 kΩ 1.14 V CML OUTPUTS Output Common Mode Voltage Switching Specifications Boldface limits apply over the operating temperature range, -40°C to +85°C. PARAMETER SYMBOL CONDITION MIN (Note 6) TYP MAX (Note 6) UNITS ADC OUTPUT Aperture Delay tA 190 ps RMS Aperture Jitter jA 100 fs 250 µs L 10 cycles tOVR 1 cycles PLL Lock Time 250 µs PLL Bandwidth 2.2 MHz Added Random Jitter 5 ps RMS Added Deterministic Jitter 7 ps P-P 5 ps rms Synchronous Clock Divider Reset Recovery Time (Note 12) Latency (ADC Pipeline Delay) Overvoltage Recovery tRSTRT DLL recovery time after Synchronous Reset SERDES Maximum Input Sample Clock Total Jitter to Maintain SERDES BER <1E-12 8 Integrated from 1kHz to 10MHz offset from carrier FN8302.0 May 1, 2012 ISLA222S Switching Specifications Boldface limits apply over the operating temperature range, -40°C to +85°C. (Continued) PARAMETER SYMBOL CONDITION SYNCP, SYNCN Setup Time (with Respect to the Positive Edge of CLKP) tRSTS AVDD, OVDD = 1.7V to 1.9V, TA = -40°C to +85°C SYNCP, SYNCN Hold Time (with respect to the positive edge of CLKP) tRSTH AVDD, OVDD = 1.7V to 1.9V, TA = -40°C to +85°C MIN (Note 6) TYP 400 75 MAX (Note 6) UNITS LVDS Inputs 150 ps 350 ps CML Outputs Output Rise Time tR 165 ps Output Fall Time tF 145 ps Data Output Duty Cycle 50 % Differential Output Resistance 100 Ω Differential Output Voltage (Note 13) 760 mVP-P SPI INTERFACE (Notes 14, 15) SCLK Period t CLK Write Operation 7 cycles tCLK Read Operation 16 cycles CSB↓ to SCLK↑ Setup Time tS Read or Write 2 cycles CSB↑ after SCLK↑ Hold Time tH Read or Write 5 cycles Data Valid to SCLK↑ Setup Time tDS Read or Write 6 cycles Data Valid after SCLK↑ Hold Time tDH Read or Write 4 cycles Data Valid after SCLK↓ Time tDVR Read 4 cycles NOTES: 11. The Tri-Level Inputs internal switching thresholds are approximately. 0.43V and 1.34V. It is advised to float the inputs, tie to ground or AVDD depending on desired function. 12. The synchronous clock divider reset function is available as a (SPI-programmable) overload on the SYNC input. 13. The voltage is expressed in peak-to-peak differential swing. The peak-to-peak single-ended swing is 1/2 of the differential swing. 14. The SPI interface timing is directly proportional to the ADC sample period (tS). Values above reflect multiples of a 4ns sample period, and must be scaled proportionally for lower sample rates. ADC sample clock must be running for SPI communication. 15. The SPI may operate asynchronously with respect to the ADC sample clock. 9 FN8302.0 May 1, 2012 ISLA222S Typical Performance Curves All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25°C, AIN = -2dBFS, fIN = 105MHz, fSAMPLE = 250MSPS. 95 SFDR AT 125 MSPS HD2 AND HD3 MAGNITUDE (dBc) SNR (dBFS) AND SFDR (dBc) SFDR AT 200 MSPS 85 SFDR AT 250 MSPS 80 75 70 65 SNR AT 125 MSPS SNR AT 250 MSPS 60 SNR AT 200 MSPS 55 50 0 100 200 HD2 AT 125 MSPS -55 90 300 400 500 HD2 AT 200 MSPS -65 HD2 AT 250 MSPS -75 -85 -95 -105 0 600 HD3 AT 200 MSPS HD3 AT 250 MSPS HD3 AT 125 MSPS 100 200 300 400 500 600 -10 0 INPUT FREQUENCY (MHz) INPUT FREQUENCY (MHz) FIGURE 3. SNR AND SFDR vs fIN FIGURE 4. HD2 AND HD3 vs fIN 0 100 90 SFDR (dBFS) 70 60 -40 H2 AND H3 SNR AND SFDR -20 SNR (dBFS) 80 SFDR (dBc) 50 40 HD3 (dBc) -60 -80 30 20 SNR (dBc) HD2 (dBc) HD2 (dBFS) -100 10 0 -60 -50 -40 -30 -20 INPUT AMPLITUDE (dBFS) -10 -120 -60 0 FIGURE 5. SNR AND SFDR vs AIN (250MSPS) HD3 (dBFS) -50 -40 -30 -20 INPUT AMPLITUDE (dBFS) FIGURE 6. HD2 AND HD3 vs AIN (250MSPS) 0 100 -20 SFDR (dBFS) SNR (dBFS) HD2 (dBc) -40 60 SFDR (dBc) H2 AND H3 SNR AND SFDR 80 40 HD3 (dBc) -60 -80 HD2 (dBFS) SNR (dBc) 20 -100 0 -60 -50 -40 -30 -20 -10 INPUT AMPLITUDE (dBFS) FIGURE 7. SNR AND SFDR vs AIN (125MSPS) 10 0 -120 -60 HD3 (dBFS) -50 -40 -30 -20 INPUT AMPLITUDE (dBFS) -10 0 FIGURE 8. H2 AND H3 vs AIN (125MSPS) FN8302.0 May 1, 2012 ISLA222S Typical Performance Curves All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25°C, AIN = -2dBFS, fIN = 105MHz, fSAMPLE = 250MSPS. (Continued) -75 HD2 AND HD3 MAGNITUDE (dBc) SNR (dBFS) AND SFDR (dBc) 90 85 SFDR 80 75 SNR 70 65 60 50 100 150 200 250 -80 H3 -85 -90 -95 H2 -100 -105 70 300 90 110 130 150 170 190 210 230 250 3500 4000 SAMPLE RATE (MSPS) SAMPLE RATE (MSPS) FIGURE 10. HD2 AND HD3 vs fSAMPLE FIGURE 9. SNR AND SFDR vs fSAMPLE 1000 1.00 3 LANE OPERATION 950 0.75 ADC CONFIGURED FOR SINGLE LANE OPERATION FOR SAMPLE RATE <= 150 MSPS 850 800 750 0.50 ADC CONFIGURED FOR TWO LANE OPERATION FOR SAMPLE RATE >= 160 MSPS 700 650 DNL (LSBs) TOTAL POWER (mW) 900 0.25 0 -0.25 -0.50 600 -0.75 550 EFFICIENT PACKING 500 40 60 80 100 120 140 160 180 SAMPLE RATE (MSPS) 200 220 -1.00 240 0 500 1000 1500 2000 2500 CODES 3000 FIGURE 12. DIFFERENTIAL NONLINEARITY (250MSPS) FIGURE 11. POWER vs fSAMPLE 2.0 85 SNR (dBFS) AND SFDR (dBc) 1.5 INL (LSBs) 1.0 0.5 0 -0.5 -1.0 80 75 70 65 -1.5 -2.0 0 500 1000 1500 2000 2500 3000 3500 CODES FIGURE 13. INTEGRAL NONLINEARITY (250MSPS) 11 4000 60 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 INPUT COMMON MODE (V) FIGURE 14. SNR AND SFDR vs VCM (250MSPS) FN8302.0 May 1, 2012 ISLA222S Typical Performance Curves 1.00 2.0 0.75 1.5 0.50 1.0 0.25 0.5 INL (LSBs) DNL (LSBs) All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25°C, AIN = -2dBFS, fIN = 105MHz, fSAMPLE = 250MSPS. (Continued) 0 -0.25 0 -0.5 -0.50 -1.0 -0.75 -1.5 -1.00 0 500 1000 1500 2000 2500 3000 3500 -2.0 4000 0 500 1000 1500 CODES STDEV = 0.49 CODES -20 AMPLITUDE (dBFS) 20145 20000 NUMBER OF HITS 3000 3500 4000 0 25000 15000 12588 10000 AIN = -2.0 dBFS SNR = 70.7 dBFS SFDR = 83.1 dBc SINAD = 70.5 dBFS -40 -60 -80 -100 5000 0 2049 0 2050 7 28 2051 2052 2053 2054 0 2055 -120 0 0 2056 20 40 60 80 100 120 FREQUENCY (MHz) CODE FIGURE 18. SINGLE-TONE SPECTRUM @ 105MHz (250MSPS) FIGURE 17. NOISE HISTOGRAM (250MSPS) 0 0 AIN = -2.0 dBFS SNR = 70.5 dBFS SFDR = 85.3 dBc SINAD = 70.3 dBFS -40 -60 -80 -100 AIN = -2.0 dBFS SNR = 69.6 dBFS SFDR = 81.2 dBc SINAD = 69.4 dBFS -20 AMPLITUDE (dBFS) -20 AMPLITUDE (dBFS) 2500 FIGURE 16. INTEGRAL NONLINEARITY (125MSPS) FIGURE 15. DIFFERENTIAL NONLINEARITY (125MSPS) 0 2000 CODES -40 -60 -80 -100 -120 0 20 40 60 80 100 120 FREQUENCY (MHz) FIGURE 19. SINGLE-TONE SPECTRUM @ 190MHz (250MSPS) 12 -120 0 20 40 60 80 100 120 FREQUENCY (MHz) FIGURE 20. SINGLE-TONE SPECTRUM @ 363MHz (250MSPS) FN8302.0 May 1, 2012 ISLA222S Typical Performance Curves All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25°C, AIN = -2dBFS, fIN = 105MHz, fSAMPLE = 250MSPS. (Continued) 25000 0 STDEV= 0.48 CODES 21035 -20 AMPLITUDE (dBFS) NUMBER OF HITS 20000 15000 11731 10000 5000 0 AIN = -2.0 dBFS SNR = 71.6 dBFS SFDR = 87.2 dBc SINAD = 71.6 dBFS -40 -60 -80 -100 0 0 2046 2 2047 2048 2049 2050 0 2051 0 -120 2052 0 10 20 0 AMPLITUDE (dBFS) AMPLITUDE (dBFS) -80 -100 -40 -60 -80 -100 10 20 30 40 50 -120 60 0 10 FREQUENCY (MHz) 20 30 40 50 60 FREQUENCY (MHz) FIGURE 23. SINGLE-TONE SPECTRUM @ 190MHz (125MSPS) FIGURE 24. SINGLE-TONE SPECTRUM @ 363MHz (125MSPS) 0 0 IMD3= -84 dBFS IMD3= -92 dBFS -20 -20 MAGNITUDE (dBFS) MAGNITUDE (dBFS) 60 AIN = -2.0 dBFS SNR = 69.5 dBFS SFDR = 71.9 dBc SINAD = 68.1 dBFS -20 -60 -40 -60 -80 -40 -60 -80 -100 -100 -120 50 0 AIN = -2.0 dBFS SNR = 71.1 dBFS SFDR = 87.3 dBc SINAD = 71.0 dBFS -40 -120 0 40 FIGURE 22. SINGLE-TONE SPECTRUM @ 105MHz (125MSPS) FIGURE 21. NOISE SPECTRUM (125MSPS) -20 30 FREQUENCY (MHz) CODE 0 20 40 60 80 FREQUENCY (MHz) 100 120 FIGURE 25. TWO-TONE SPECTRUM (F1 = 70MHz, F2 = 71MHz AT -7dBFS) (250MSPS) 13 -120 0 20 40 60 80 FREQUENCY (MHz) 100 120 FIGURE 26. TWO-TONE SPECTRUM (F1 = 170MHz, F2 = 171MHz AT -7dBFS) (250MSPS) FN8302.0 May 1, 2012 ISLA222S Typical Performance Curves All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25°C, AIN = -2dBFS, fIN = 105MHz, fSAMPLE = 250MSPS. (Continued) FIGURE 27. SERDES DATA EYE at 1.0Gbps FIGURE 28. SERDES DATA EYE at 3.0Gbps FIGURE 29. SERDES DATA EYE at 4.375Gbps FIGURE 30. SERDES BATHTUB at 1.0Gbps FIGURE 31. SERDES BATHTUB at 3.0Gbps FIGURE 32. SERDES BATHTUB at 4.375Gbps 14 FN8302.0 May 1, 2012 ISLA222S Typical Performance Curves All Typical Performance Characteristics apply under the following conditions unless otherwise noted: AVDD = OVDD = 1.8V, TA = +25°C, AIN = -2dBFS, fIN = 105MHz, fSAMPLE = 250MSPS. (Continued) FIGURE 33. SERDES HISTOGRAM at 1.0Gbps FIGURE 34. SERDES HISTOGRAM at 3.0Gbps FIGURE 35. SERDES HISTOGRAM at 4.375Gbps Theory of Operation Functional Description The ISLA222S is based upon a 12-bit, 250MSPS ADC converter core that utilizes a pipelined successive approximation architecture (see Figure 36). The input voltage is captured by a Sample-Hold Amplifier (SHA) and converted to a unit of charge. Proprietary charge-domain techniques are used to successively compare the input to a series of reference charges. Decisions made during the successive approximation operations determine the digital code for each input value. Digital error correction is also applied. Power-On Calibration The ADC core(s) perform a self-calibration at start-up. An internal power-on-reset (POR) circuit detects the supply voltage ramps and initiates the calibration when the analog and digital supply 15 voltages are above a threshold. The following conditions must be adhered to for the power-on calibration to execute successfully: • A frequency-stable conversion clock must be applied to the CLKP/CLKN pins • DNC pins must not be connected • SDO has an internal pull-up and should not be driven externally • RESETN is pulled low by the ADC internally during POR. External driving of RESETN is optional. • SPI communications must not be attempted during calibration, with the only exception of performing read operations on the cal_done register at address 0xB6. A user-initiated reset can subsequently be invoked in the event that the above conditions cannot be met at power-up. FN8302.0 May 1, 2012 ISLA222S CLOCK GENERATION INP 2.5-BIT 2.5-BIT FLASH SHA FLASH INN 1.25V + – 6- STAGE 1.5-BIT/ STAGE 3- STAGE 1-BIT/ STAGE 3-BIT FLASH DIGITAL ERROR CORRECTION FIGURE 36. ADC CORE BLOCK DIAGRAM After the power supply has stabilized, the internal POR releases RESETN and an internal pull-up pulls it high, which starts the calibration sequence. If a subsequent user-initiated reset is desired, the RESETN pin should be connected to an open-drain driver with an off-state/high impedance state leakage of less than 0.5mA to assure exit from the reset state so calibration can start. The calibration sequence is initiated on the rising edge of RESETN, as shown in Figure 37. Calibration status can be determined by reading the cal_status bit (LSB) at 0xB6. This bit is ‘0’ during calibration and goes to a logic ‘1’ when calibration is complete. During calibration the JESD204 transmitter PLL is not locked to the ADC sample clock, so the CML outputs will toggle at an undetermined rate. Normal operation is resumed once calibration is complete. At 250MSPS the nominal calibration time is 280ms, while the maximum calibration time is 550ms. CLKN CLKP CALIBRATION TIME RESETN CAL_STATUS BIT CALIBRATION BEGINS CALIBRATION COMPLETE FIGURE 37. CALIBRATION TIMING 16 User Initiated Reset Recalibration of the ADC can be initiated at any time by driving the RESETN pin low for a minimum of one clock cycle. An open-drain driver with a drive strength in its high impedance state of less than 0.5mA is recommended, as RESETN has an internal high impedance pull-up to OVDD. As is the case during power-on reset, RESETN and DNC pins must be in the proper state for the calibration to successfully execute. The performance of the ISLA222S changes with variations in temperature, supply voltage or sample rate. The extent of these changes may necessitate recalibration, depending on system performance requirements. Best performance will be achieved by recalibrating the ADC under the environmental conditions at which it will operate. A supply voltage variation of <100mV will generally result in an SNR change of <0.5dBFS and SFDR change of <3dBc. In situations where the sample rate is not constant, best results will be obtained if the device is calibrated at the highest sample rate. Reducing the sample rate by less than 80MSPS will typically result in an SNR change of <0.5dBFS and an SFDR change of <3dBc. Figures 38 through 43 show the affect of temperature on SNR and SFDR performance with power on calibration performed at -40°C, +25°C, and +85°C. Each plot shows the variation of SNR/SFDR across temperature after a single power on calibration at -40°C, +25°C and +85°C. Best performance is typically achieved by a user-initiated power on calibration at the operating conditions, as stated earlier. However, it can be seen that performance drift with temperature is not a very strong function of the temperature at which the power on calibration is performed. FN8302.0 May 1, 2012 ISLA222S Temperature Calibration 73 95 -2dBFS, 125MSPS -2dBFS, 125MSPS SNR (dBFS) -2dBFS, 200MSPS SFDR (dBc) -2dBFS, 250MSPS 72 -2dBFS, 250MSPS 90 -2dBFS, 200MSPS 85 -1dBFS, 250MSPS 71 -1dBFS, 200MSPS -1dBFS, 125MSPS -1dBFS, 125MSPS -1dBFS, 200MSPS 80 -1dBFS, 250MSPS 70 -40 -35 -30 -25 75 -40 -20 -35 TEMPERATURE (°C) FIGURE 38. TYPICAL SNR PERFORMANCE vs TEMPERATURE, DEVICE CALIBRATED AT -40°C, fIN = 105MHz -30 TEMPERATURE (°C) -25 -20 FIGURE 39. TYPICAL SFDR PERFORMANCE vs TEMPERATURE, DEVICE CALIBRATED AT -40°C, fIN = 105MHz 90 72 -2dBFS, 125MSPS -2dBFS, 200MSPS -2dBFS, 250MSPS -2dBFS, 200MSPS -2dBFS, 125MSPS -2dBFS, 250MSPS SFDR (dBc) SNR (dBFS) 85 71 80 -1dBFS, 125MSPS -1dBFS, 125MSPS -1dBFS, 200MSPS -1dBFS, 250MSPS -1dBFS, 200MSPS -1dBFS, 250MSPS 70 5 10 15 20 25 30 TEMPERATURE (°C) 35 40 75 45 5 10 15 20 25 30 TEMPERATURE (°C) 35 40 45 FIGURE 41. TYPICAL SFDR PERFORMANCE vs TEMPERATURE, DEVICE CALIBRATED AT +25°C, fIN = 105MHz FIGURE 40. TYPICAL SNR PERFORMANCE vs TEMPERATURE, DEVICE CALIBRATED AT +25°C, fIN = 105MHz 90 72 -2dBFS, 125MSPS -2dBFS, 250MSPS -2dBFS, 125MSPS -2dBFS, 200MSPS -2dBFS, 200MSPS 85 SNR (dBFS) SFDR (dBc) 71 -2dBFS, 250MSPS 80 70 -1dBFS, 125MSPS -1dBFS, 200MSPS -1dBFS, 200MSPS -1dBFS, 250MSPS -1dBFS, 125MSPS -1dBFS, 250MSPS 69 65 67 69 71 73 75 77 79 TEMPERATURE (°C) 81 83 FIGURE 42. TYPICAL SNR PERFORMANCE vs TEMPERATURE, DEVICE CALIBRATED AT +85°C, fIN = 105MHz 17 85 75 65 70 75 TEMPERATURE (°C) 80 85 FIGURE 43. TYPICAL SFDR PERFORMANCE vs TEMPERATURE, DEVICE CALIBRATED AT +85°C, fIN = 105MHz FN8302.0 May 1, 2012 ISLA222S Analog Input A single fully differential input (VINP/VINN) connects to the sample and hold amplifier (SHA) of each unit ADC. The ideal full-scale input voltage is 2.0V, centered at the VCM voltage as shown in Figure 44. ADC VINN 1.8 VINP 1.4 VCM 1.0V 1.0 FIGURE 47. DIFFERENTIAL AMPLIFIER INPUT 0.6 0.2 FIGURE 44. ANALOG INPUT RANGE Best performance is obtained when the analog inputs are driven differentially. The common-mode output voltage, VCM, should be used to properly bias the inputs as shown in Figures 45 through 47. An RF transformer will give the best noise and distortion performance for wideband and/or high intermediate frequency (IF) inputs. Two different transformer input schemes are shown in Figures 45 and 46. ADT1-1WT ADT1-1WT 1000pF ADC VCM 0.1µF FIGURE 45. TRANSFORMER INPUT FOR GENERAL PURPOSE APPLICATIONS ADTL1-12 TX-2-5-1 1000pF ADC A differential amplifier, as shown in the simplified block diagram in Figure 47, can be used in applications that require DC-coupling. In this configuration, the amplifier will typically dominate the achievable SNR and distortion performance. Intersil’s new ISL552xx differential amplifier family can also be used in certain AC applications with minimal performance degradation. Contact Intersil sales support with your needs. When an over range occurs, the data sample output bits are held at full scale (all 0’s or all 1’s), thus allowing the detection of this condition in the receiver device. Clock Input The clock input circuit is a differential pair (see Figure 61 on page 37). Driving these inputs with a high level (up to 1.8VP-P on each input) sine or square wave will provide the lowest jitter performance. A transformer with 4:1 impedance ratio will provide increased drive levels. The clock input is functional with AC-coupled LVDS, LVPECL, and CML drive levels. To maintain the lowest possible aperture jitter, it is recommended to have high slew rate at the zero crossing of the differential clock input signal. The recommended drive circuit is shown in Figure 48. A duty range of 40% to 60% is acceptable. The clock can be driven single-ended, but this will reduce the edge rate and may impact SNR performance. The clock inputs are internally self-biased to AVDD/2 through a Thevenin equivalent of 10kΩ to facilitate AC coupling. VCM TC4-19G2+ 1000pF 1000pF CLKP FIGURE 46. TRANSMISSION-LINE TRANSFORMER INPUT FOR HIGH IF APPLICATIONS This dual transformer scheme is used to improve common-mode rejection, which keeps the common-mode level of the input matched to VCM. The value of the shunt resistor should be determined based on the desired load impedance. The differential input resistance of the ISLA222S is 600Ω. The SHA design uses a switched capacitor input stage (see Figure 60 on page 37), which creates current spikes when the sampling capacitance is reconnected to the input voltage. This causes a disturbance at the input, which must settle before the next sampling point. Lower source impedance will result in faster settling and improved performance. Therefore a 2:1 or 1:1 transformer and low shunt resistance are recommended for optimal performance. 18 0.01µF 200 CLKN 1000pF 1000pF FIGURE 48. RECOMMENDED CLOCK DRIVE A selectable 2x or 4x frequency divider is provided in series with the clock input. The divider can be used in the 2x mode with a sample clock equal to twice the desired sample rate or in 4x mode with a sample clock equal to four times the desired sample rate. Use of the 2x or 4x frequency divider enables the use of the Phase Slip feature, which enables the system to be able to select the phase of the FN8302.0 May 1, 2012 ISLA222S Voltage Reference divide by 2 or divide by 4 that causes the ADC to sample the analog input. A temperature compensated internal voltage reference provides the reference charges used in the successive approximation operations. The full-scale range of each ADC is proportional to the reference voltage. The nominal value of the voltage reference is 1.25V. TABLE 1. CLKDIV PIN SETTINGS CLKDIV PIN DIVIDE RATIO AVSS 2 Float 1 Digital Outputs AVDD 4 The digital outputs are in CML format, and feature analog and digital characteristics compliant with the JESD204 standard requirements. The clock divider can also be controlled through the SPI port, which overrides the CLKDIV pin setting. See “SPI Physical Interface” on page 27. A delay-locked loop (DLL) generates internal clock signals for various stages within the charge pipeline. If the frequency of the input clock changes, the DLL may take up to 52μs to regain lock at 250MSPS. The lock time is inversely proportional to the sample rate. The DLL has two ranges of operation, slow and fast. The slow range can be used for ADC core sample rates between 40MSPS and 100MSPS, while the default fast range can be used from 80MSPS to the maximum specified sample rate. The lane data rate is related to the ADC core sample rate by a relationship that is defined by the JESD204 transmitter configuration, and has additional frequency constraints; see“JESD204 Transmitter” on page 20 for additional details. Jitter In a sampled data system, clock jitter directly impacts the achievable SNR performance. The theoretical relationship between clock jitter (tJ) and SNR is shown in Equation 1 and is illustrated in Figure 49. 1 SNR = 20 log 10 ⎛ --------------------⎞ ⎝ 2πf t ⎠ IN J (EQ. 1) 100 95 tj = 0.1ps 90 SNR (dB) tj = 1ps 75 12 BITS 70 tj = 10ps 65 60 10 BITS tj = 100ps 55 50 1M 10M 100M INPUT FREQUENCY (Hz) 1G FIGURE 49. SNR vs CLOCK JITTER This relationship shows the SNR that would be achieved if clock jitter were the only non-ideal factor. In reality, achievable SNR is limited by internal factors such as linearity, aperture jitter and thermal noise as well. Internal aperture jitter is the uncertainty in the sampling instant. The internal aperture jitter combines with the input clock jitter in a root-sum-square fashion, since they are not statistically correlated, and this determines the total jitter in the system. The total jitter, combined with other noise sources, then determines the achievable SNR. 19 The power dissipated by the device is dependent on the ADC sample rate and the number of active lanes in the link. There is a fixed bias current drawn from the analog supply for the ADC, along with a fixed bias current drawn from the digital supply for each active lane. The remaining power dissipation is linearly related to the sample rate. Nap/Sleep Portions of the device may be shut down to save power during times when operation of the ADC is not required. Two power saving modes are available: Nap, and Sleep. Nap mode reduces power dissipation significantly while taking a very short time to return to functionality. Sleep mode reduces power consumption drastically while taking longer to return to functionality. In Nap mode the JESD204 lanes will continue to produce valid encoded data, allowing the link to remain active and thus return to a functional state quickly. The data transmitted over the lanes in nap mode is the last valid ADC sample, repeated until leaving nap mode. The 8b/10b encoder’s running disparity will prevent the potentially long time repetition of this last valid sample from creating DC bias on the lane. In sleep mode, the JESD204 lanes will be deactivated to conserve power. Thus, sometime after wake up code group alignment will be required to reestablish the link. The input clock should remain running and at a fixed frequency during Nap or Sleep, and CSB should be high. The JESD204 link will only remain established during nap mode if the input clock continues to remain stable during the nap period. 14 BITS 85 80 Power Dissipation By default after the device is powered on, the operational state is controlled by the NAPSLP pin as shown in Table 2. Please note that power on calibration occurs at power-up time regardless of the state of the NAPSLP pin; immediately following this power on calibration routine, the device will enter nap or sleep state if the NAPSLP pin voltage dictates it is to do so. TABLE 2. NAPSLP PIN SETTINGS NAPSLP PIN MODE AVSS Normal Float Nap AVDD Sleep The power-down mode can also be controlled through the SPI port, which overrides the NAPSLP pin setting. Details on this are contained in “Serial Peripheral Interface” on page 27. FN8302.0 May 1, 2012 ISLA222S Data Format . Output data can be presented in three formats: two’s complement(default), Gray code and offset binary. The data format can be controlled through the SPI port by writing to address 0x73. Details on this are contained in “Serial Peripheral Interface” on page 27. Offset binary coding maps the most negative input voltage to code 0x000 (all zeros) and the most positive input to 0xFFF (all ones). Two’s complement coding simply complements the MSB of the offset binary representation. When calculating Gray code the MSB is unchanged. The remaining bits are computed as the XOR of the current bit position and the next most significant bit. Figure 50 shows this operation. BINARY 11 10 9 •••• 1 0 •••• GRAY CODE 11 10 •••• 9 1 0 FIGURE 50. BINARY TO GRAY CODE CONVERSION Converting back to offset binary from Gray code must be done recursively, using the result of each bit for the next lower bit as shown in Figure 51. GRAY CODE 11 10 9 •••• 1 0 TABLE 3. INPUT VOLTAGE TO OUTPUT CODE MAPPING INPUT VOLTAGE OFFSET BINARY TWO’S COMPLEMENT GRAY CODE –Full Scale 0000 0000 0000 1000 0000 0000 0000 0000 0000 –Full Scale + 1LSB 0000 0000 0001 1000 0000 0001 0000 0000 0001 Mid–Scale 1000 0000 0000 0000 0000 0000 1100 0000 0000 +Full Scale – 1LSB 1111 1111 1110 0111 1111 1110 1000 0000 0001 +Full Scale 1111 1111 1111 0111 1111 1111 1000 0000 0000 Clock Divider Synchronous Reset The function of clock divider synchronous reset is available as a SPI-programmable overloaded function on the SYNCP and SYNCN pins. Given that the clock divider reset and SYNC features have the same electrical and timing requirements, this overloading allows the system to generate only a single well timed signal with respect to the ADC sample clock and select the ADC’s interpretation of the signal as a SPI-programmable option (see SPI register 0x77 description for more information). By default the SYNCP and SYNCN pins will function as the JESD204 SYNC~. The use of clock divider reset function is a requirement in a system that uses the ISLA214S50, ISLA214S35, or CLKDIV = 2 or 4 and also requires time alignment or deterministic latency of multiple devices. Please contact Intersil sales support with your needs about this feature and its usage. Soft Reset Soft reset is a function intended to be used when the power on reset is to be re-run. An application may decide to issue a soft calibration command after significant temperature change or after a change in the sample rate frequency to optimize performance under the new condition. •••• Soft reset is issued by writing the Soft Reset bit at SPI address 0x00. Soft reset is a self-resetting bit in that will automatically return to 0 once the power on calibration has completed. JESD204 Transmitter Overview •••• BINARY 11 10 9 •••• 1 FIGURE 51. GRAY CODE TO BINARY CONVERSION Mapping of the input voltage to the various data formats is shown in Table 3. 20 0 The conversion data is presented by a JESD204B-compliant SERDES interface. The SERDES lane data rate supports typical speeds up to 4.375Gbps, exceeding the 3.125Gbps maximum specified by the JESD204 rev A standard. Two packing modes are supported: Efficient and Simple. A SYNC input is included, which is used for lane initialization as well as time alignment of multiple converter devices. AC coupling of the SERDES lane(s) on the board is required. A block diagram of this SERDES transmitter is shown in Figure 52. For more information about the standardized characteristics and features of a JESD204 interface, please see JESD204 rev A and rev B standards. For application design support, including evaluation kit schematics and layout, reference FPGA project(s), and simulation models for functionality and signal integrity, please contact Intersil sales support with your needs and/or view application notes on the Intersil website. FN8302.0 May 1, 2012 ISLA222S SERDES Block Link Layer Sample Data Analog Input Analog Input Sample Clock Transport Layer Scrambler 1+x14+x15 Encoder 8/10 Lane 0 SER Logic Sample Data PLL Multiply Clock Management - Code group Synchronization - Alignment Characters - Initial Lane Synchronization - Etc SYNC Link Layer Lane 1 Link Layer Lane 2 FIGURE 52. SERDES TRANSMITTER BLOCK DIAGRAM To maximize flexibility at the system level, two transport layer packing modes are supported: simple and efficient. These two modes allow the system designer flexibility to trade off between the number of lanes to support a given throughput, the data rate of these lanes, and the complexity of the receiver. This translates directly into providing system level trade-offs between cost, power, and resource usage of the receiver and complexity of the solution. Simple mode packs informationless bits onto each ADC sample to form full 16-bit data. In simple mode packing, the frame clock and ADC sample clock are the same frequency, easing frequency scaling requirements at the system level, but decreasing the payload efficiency of the lanes. Decreased payload efficiency of the lanes increases the lane data rate required to support a given throughput, and may require additional lanes to support a given configuration. The degree of payload efficiency loss is dependent on the ADC resolution. Efficient mode packs sequential ADC samples into a contiguous block of an integer number of octets, and then slices the block into the octets for transport. This mode always achieves the theoretical maximum payload of the lanes (80%) regardless of the resolution of the ADC and the number of lanes used. This mode provides the minimum number of lanes at the minimum data rate that is theoretically possible given the 8b/10b encoding used in JESD204 systems. In efficient packing mode, frame clock and the ADC sample clock have an M/N relationship, where M and N are small integers and vary depending on the ADC resolution and number of lanes selected. Efficient mode packing may require additional frequency scaling elements (internal FPGA PLLs or discrete frequency scaling devices) to generate the frame clock for the receiving device. 21 The default configuration for this device is efficient packing mode. Reconfiguration into the simple packing mode is accomplished by programming the JESD204 parameters via the SPI bus. See Table 5 for the full list of parameters values for each mode and product. Via SPI, the JESD204 transmitter is highly configurable, supporting efficient to simple mode packing reconfiguration as well as “downgrading” a given product’s JESD204 interface. For example, reconfiguring a 3-lane product into 2 lanes (with each running faster than with 3 lanes), or reducing the resolution of the ADC(s) to slow down the lane data rate in systems where the full ADC resolution is not required, are supported. Please contact Intersil sales support for a full list of downgradeable configurations that are supported. Signal integrity plots, including data eye, BER bathtub curves, and edge histogram plots versus lane data rate can be found in the “Typical Performance Curves” beginning on page 10. Initial Lane Alignment The link initialization process is started by asserting the SYNC~ signal to the ADC device. This assertion causes the JESD204 transmitter to generate comma characters, which are used by the receiver to accomplish code group synchronization (bit and octet alignment, respectively). Once code group synchronization is detected in the receiver, it de-asserts the SYNC~ signal, causing the JESD204 transmitter to generate the initial lane alignment sequence (ILA). The ILA is comprised of 4 multi-frames of data in a standard format, with the length of each multi-frame determined by the K parameter as programmed into the SPI JESD204 parameter table. The ILA includes standard control character markers that can be used to perform channel bonding in the receiving device if desired. The 2nd multi-frame includes the full JESD204 parameter FN8302.0 May 1, 2012 ISLA222S data, allowing the receiver to auto-detect the lane configuration if desired. After completion of the ILA the JESD204 transmitter begins transmitting ADC sample data. Continuous link and lane alignment monitoring is accomplished via an octet substitution scheme. The last octet in each frame, if identical to the last octet in the previous frame, is replaced with a specific control character. If both sides of the link support lane synchronization, the last octet in each multi-frame, if identical to the last octet in the previous frame, is replaced with a different specific control character. A more complete description of the link initialization sequence, including finite state machine implementation, can be found in the JESD204 rev A standard. LANE DATA RATE The lane data rate for this product family is a function of the ADC sample rate, the number of SERDES lanes used, and packing mode selected in the SERDES transmitter. Figure 53 illustrates the relationship between ADC sample rate and SERDES lane rate for various transmitter configurations. The SERDES can typically operate from lane rates of 1 to over 4.375Gbs. For each ADC speed grade, the SERDES lanes are tested at its maximum ADC sample rate using three lane efficient packing as well as twolane, efficient packing for the 250 and 200MSPS speed versions and one-lane, efficient packing for 125MSPS speed version. passes the lane alignment sequence through its descrambler. Even if the receiver does not implement this detail, the 3rd and subsequent octets can be descrambled to yield ADC data due to the self-synchronizing nature of the scrambler used. MULTI-CHIP TIME ALIGNMENT The JESD204 standard (in various revisions) provides the capability to time align multiple JESD204 ADC devices to a single logic device (FPGA or ASIC). This feature is critical in many applications that cannot tolerate the variable latency of the JESD204 link, and that must process pipeline depth correct data from more than one ADC device. Time alignment of multiple devices provides the capability to align samples from multiple JESD204 ADC devices in the system in a pipeline-depth correct manner, thus enabling the system to analyze the ADC data from multiple devices while eliminating the variable latency of the JESD204 link as a concern. This capability enables configurations of JESD204 ADCs as IQ, interleave, and/or simultaneously-sampled converters. This ADC family uses the asserted to de-asserted SYNC~ transition as the absolute time event with which to generate a known sequence of characters at the JESD204 transmitter of equal pipeline depth between all ADC devices in the system to be time aligned. This is consistent with the JESD204 rev B subclass 2 device definition. 4500 1 Lane (Efficient Packing) LANE RATE (MBPS) 4000 3.125 GBPS (JESD204) 3500 4.375 GBPS 2 Lanes (Simple Packing) 3000 2500 2000 2 Lanes (Efficient Packing) 1500 1000 3 Lanes (Simple Packing) 3 Lanes (Efficient Packing) 50 70 90 110 130 150 170 190 210 230 250 ADC SAMPLE RATE (MSPS) FIGURE 53. LANE DATA RATE AS A FUNCTION OF ADC SAMPLE RATE, PACKING SCRAMBLER The bypassable scrambler is compliant with the scrambler defined in the JESD204 rev A standard. This implementation seeds the scrambler with the initial lane alignment sequence, such that the first two octets following the sequence can be properly descrambled if the receiver also 22 Test Patterns The complexity of the JESD204 interface merits much more test pattern capability than less complex parallel interfaces. This device family consequently supports a much wider range of test patterns than previous ADC families. Supported test patterns include both transport and link layer patterns. Transport layer patterns are passed through the transport layer of the JESD204 transmitter, following the same sequence of being packed and sliced into octets as the ADC sample data. Link layer test patterns bypass the transport layer and are injected directly into the 8b/10b encoder, serialized, and sent out of the physical media. Test pattern generation is controlled through SPI register 0xC0. Link layer PRBS patterns are standard PRBS patterns that can be used with built-in standard PRBS checkers in, for example, FPGA SERDES-capable pins. All transport layer test patterns re-initialize their phase when the SYNC~ de-assertion occurs; consequently, a system that provides a well-timed SYNC~ signal with respect to the ADC sample clock can expect transport layer test patterns to have consistent phase with respect to that de-assertion, which can be a significant aid when debugging the system. FN8302.0 May 1, 2012 ISLA222S TABLE 4. JESD204 CONFIGURATIONS AND CLOCK FREQUENCIES ADC SAMPLE CLOCK RANGE (MHz) LANE DATA RATE MULTIPLIER FROM ADC SAMPLE CLOCK RATE LANE DATA RATE (GBPS) 100-250 (Efficient Packing) 3 Lanes (12-bits)*(2 ADC channels)*(10/8 encoder overhead)/(3 lanes) = (240/24) = 10.0 1.00 to 2.50 66.67-250 (Efficient Packing) 2 Lanes (12-bits)*(2 ADC channels)*(10/8 encoder overhead)/(2 lanes) = (240/16) = 15 1.00 to 3.75 50-218.75(Simple Packing) 2 Lanes (12-bits+4-bit tail)*(2 ADC channels)*(10/8 encoder overhead)/(2 lanes) = (320/16) = 20 1.00 to 4.375 40-145.8 (Efficient Packing) 1 Lane (12-bits)*(2 ADC channels)*(10/8 encoder overhead)/(1 lane) = (240/8) = 30 1.20 to 4.375 40-109.375(Simple Packing) 1 Lane (12-bits+4-bit tail)*(2 ADC channels)*(10/8 encoder overhead)/(1 lane) = (320/8) = 40 1.60 to 4.375 TABLE 5. JESD204 PARAMETERS PACKING NUMBER JESD204 MODE OF LANES PARAMETER ENCODED Efficient Efficient 3 2 CF = 0 0 CS = 0 0 F=6 5 HD = 0 0 L=3 2 M=2 1 N = 12 11 N' = 12 11 S=6 5 K >= 3 >= 2 CF = 0 0 CS = 0 0 F=3 2 HD = 0 0 L=2 1 M=2 1 N = 12 11 N' = 12 11 S=2 1 K >= 6 >=5 23 JESD204 PARAMETERS AND FRAME MAP (Notes 16, 17, 18) C0S0[11:4 C0S0[3:0] C0S1[7:0] C0S2[11:4] COS1[11:8] C0S4[11:4] C0S4[3:0] C0S5[7:0] C1S0[11:4] C1S0[3:0] C1S1[7:0] C1S1[11:8] C1S3[7:0] C1S3[11:8] C0S0[11:4] C0S0[3:0] COS3[7:0] COS3[11:8] C0S5[11:8] C1S2[11:4] C1S2[3:0] C0S2[3:0] C1S4[11:4] C1S4[3:0] C1S5[7:0] C1S5[11:8] C0S1[7:0] C0S1[11:8] C1S0[11:4] C1S0[3:0] C1S1[7:0] C1S1[11:8] FN8302.0 May 1, 2012 ISLA222S TABLE 5. JESD204 PARAMETERS (Continued) PACKING NUMBER JESD204 MODE OF LANES PARAMETER ENCODED Simple Efficient Simple 2 1 1 CF = 0 0 CS = 0 0 F=2 1 HD = 0 0 L=2 1 M=2 1 N = 12 11 N' = 16 15 S=1 0 K >= 9 >= 8 CF = 0 0 CS = 0 0 F=6 5 HD = 0 0 L=1 0 M=2 1 N = 12 11 N' = 12 11 S=2 1 K >= 3 >= 2 CF = 0 0 CS = 0 0 F=4 3 HD = 0 0 L=1 0 M=2 1 N = 12 11 N' = 16 15 S=1 0 K >= 5 >= 4 JESD204 PARAMETERS AND FRAME MAP (Notes 16, 17, 18) C0S0[11:4] C0S0[3:0] TTTT C1S0[11:4] C1S0[3:0] TTTT C0S0[11:4] C0S0[3:0] C0S1[7:0] C1S0[11:4] COS1[11:8] C0S0[11:4] C0S0[3:0] TTTT C1S0[3:0] C1S1[7:0] C1S1[11:8] C1S0[11:4] C1S0[3:0] TTTT NOTES: 16. The JESD204 parameters are shown as their actual values, with the JESD204 encoded values (i.e., the values that are programmed into the SPI registers) in the next column over. Typically values that must always be greater than 1 are encoded as value minus 1, and so on. 17. Frame map format decoder: "CxSy[a:b]" = Converter x, Sample y, bits a through b. For example, "C0S0[13:6]" = Converter 0, Sample 0, bits 13 through 6, etc. "T" = Tail bit (information-less bit packed in the transport layer mapping to form octets). 18. The topmost lane in the graphical frame map is Lane0, followed by Lane1 and Lane 2 (for 3-lane configurations). 24 FN8302.0 May 1, 2012 ISLA222S CSB SCLK SDIO R/W W1 W0 A12 A11 A1 A10 A0 D7 D6 D5 D4 D3 D2 D1 D0 D2 D3 D4 D5 D6 D7 FIGURE 54. MSB-FIRST ADDRESSING CSB SCLK SDIO A0 A1 A11 A2 A12 W0 W1 R/W D1 D0 FIGURE 55. LSB-FIRST ADDRESSING tDSW CSB tCLK tHI tDHW tS tH tLO SCLK SDIO R/W W1 W0 A12 A11 A10 A9 A8 A7 D5 D4 D3 D2 D1 D0 SPI WRITE FIGURE 56. SPI WRITE tDSW CSB tCLK tHI tDHW tH tDVR tS tLO SCLK WRITING A READ COMMAND READING DATA ( 3 WIRE MODE ) SDIO R/W W1 W0 A12 A11 A10 A9 A2 A1 A0 D7 SDO D6 D3 D2 D1 D0 ( 4 WIRE MODE) D7 D3 D2 D1 D0 SPI READ FIGURE 57. SPI READ 25 FN8302.0 May 1, 2012 ISLA222S CSB STALLING CSB SCLK SDIO INSTRUCTION/ADDRESS DATA WORD 1 DATA WORD 2 FIGURE 58. 2-BYTE TRANSFER LAST LEGAL CSB STALLING CSB SCLK SDIO INSTRUCTION/ADDRESS DATA WORD 1 DATA WORD N FIGURE 59. N-BYTE TRANSFER 26 FN8302.0 May 1, 2012 ISLA222S Serial Peripheral Interface A serial peripheral interface (SPI) bus is used to facilitate configuration of the device and to optimize performance. The SPI bus consists of chip select (CSB), serial clock (SCLK) serial data output (SDO), and serial data input/output (SDIO). The maximum SCLK rate is equal to the ADC sample rate (fSAMPLE) divided by 7 for write operations and fSAMPLE divided by 16 for reads. There is no minimum SCLK rate. The following sections describe various registers that are used to configure the SPI or adjust performance or functional parameters. Many registers in the available address space (0x00 to 0xFF) are not defined in this document. Additionally, within a defined register there may be certain bits or bit combinations that are reserved. Undefined registers and undefined values within defined registers are reserved and should not be selected. Setting any reserved register or value may produce indeterminate results. After the instruction/address bytes have been read, the appropriate number of data bytes are written to or read from the ADC (based on the R/W bit status). The data transfer will continue as long as CSB remains low and SCLK is active. Stalling of the CSB pin is allowed at any byte boundary (instruction/address or data) if the number of bytes being transferred is three or less. For transfers of four bytes or more, CSB is allowed to stall in the middle of the instruction/address bytes or before the first data byte. If CSB transitions to a high state after that point the state machine will reset and terminate the data transfer. TABLE 6. BYTE TRANSFER SELECTION [W1:W0] BYTES TRANSFERRED 00 1 01 2 10 3 11 4 or more SPI Physical Interface The serial clock pin (SCLK) provides synchronization for the data transfer. By default, all data is presented on the serial data input/output (SDIO) pin in three-wire mode. The state of the SDIO pin is set automatically in the communication protocol (described in the following). A dedicated serial data output pin (SDO) can be activated by setting 0x00[7] high to allow operation in four-wire mode. The SPI port operates in a half duplex master/slave configuration, with the ADC functioning as a slave. Multiple slave devices can interface to a single master in three-wire mode only, since the SDO output of an unaddressed device is asserted in four wire mode. The chip-select bar (CSB) pin determines when a slave device is being addressed. Multiple slave devices can be written to concurrently, but only one slave device can be read from at a given time (again, only in three-wire mode). If multiple slave devices are selected for reading at the same time, the results will be indeterminate. The communication protocol begins with an instruction/address phase. The first rising SCLK edge following a high-to-low transition on CSB determines the beginning of the two-byte instruction/address command; SCLK must be static low before the CSB transition. Data can be presented in MSB-first order or LSB-first order. The default is MSB-first, but this can be changed by setting 0x00[6] high. Figures 54 and 55 show the appropriate bit ordering for the MSB-first and LSB-first modes, respectively. In MSB-first mode, the address is incremented for multi-byte transfers, while in LSB-first mode it’s decremented. In the default mode, the MSB is R/W, which determines if the data is to be read (active high) or written. The next two bits, W1 and W0, determine the number of data bytes to be read or written (see Table 6). The lower 13 bits contain the first address for the data transfer. This relationship is illustrated in Figure 56, and timing values are given in “Switching Specifications” on page 8. 27 Figures 58 and 59 illustrate the timing relationships for 2-byte and N-byte transfers, respectively. The operation for a 3-byte transfer can be inferred from these diagrams. SPI Configuration ADDRESS 0X00: CHIP_PORT_CONFIG Bit ordering and SPI reset are controlled by this register. Bit order can be selected as MSB to LSB (MSB first) or LSB to MSB (LSB first) to accommodate various micro controllers. Bit 7 SDO Active Bit 6 LSB First Setting this bit high configures the SPI to interpret serial data as arriving in LSB to MSB order. Bit 5 Soft Reset Setting this bit high resets all SPI registers to default values. Bit 4 Reserved This bit should always be set high. Bits 3:0 These bits should always mirror bits 4:7 to avoid ambiguity in bit ordering. ADDRESS 0X02: BURST_END If a series of sequential registers are to be set, burst mode can improve throughput by eliminating redundant addressing. The burst is ended by pulling the CSB pin high. Setting the burst_end address determines the end of the transfer. During a write operation, the user must be cautious to transmit the correct number of bytes based on the starting and ending addresses. Bits 7:0 Burst End Address This register value determines the ending address of the burst data. FN8302.0 May 1, 2012 ISLA222S Device Information to enable updates written to 0x23 and 0x24 to be used by the ADC (see description for 0xFE).. ADDRESS 0X08: CHIP_ID TABLE 8. COARSE GAIN ADJUSTMENT ADDRESS 0X09: CHIP_VERSION 0x22[3:0] CoreA 0x26[3:0] CoreB NOMINAL COARSE GAIN ADJUST (%) Bit3 +2.8 Device Configuration/Control Bit2 +1.4 A common SPI map, which can accommodate single-channel or multi-channel devices, is used for all Intersil ADC products. Bit1 -2.8 Bit0 -1.4 The generic die identifier and a revision number, respectively, can be read from these two registers. ADDRESS 0X20: OFFSET_COARSE_COREA TABLE 9. MEDIUM AND FINE GAIN ADJUSTMENTS ADDRESS 0X21: OFFSET_FINE_COREA The input offset of the ADC core can be adjusted in fine and coarse steps. Both adjustments are made via an 8-bit word as detailed in Table 7. The data format is twos complement.The data format is twos complement. Bit 0 in register 0xFE must be set high to enable updates written to 0x20 and 0x21 to be used by the ADC (see description for 0xFE). The default value of each register will be the result of the self-calibration after initial power-up. If a register is to be incremented or decremented, the user should first read the register value then write the incremented or decremented value back to the same register. TABLE 7. OFFSET ADJUSTMENTS CoreA CoreB PARAMETER 0x20[7:0] 0x26[7:0] COARSE OFFSET 0x21[7:0] 0x27[7:0] FINE OFFSET Steps 255 255 –Full Scale (0x00) -133LSB (-47mV) -5LSB (-1.75mV) Mid–Scale (0x80) 0.0LSB (0.0mV) 0.0LSB +Full Scale (0xFF) +133LSB (+47mV) +5LSB (+1.75mV) Nominal Step Size 1.04LSB (0.37mV) 0.04LSB (0.014mV) ADDRESS 0X22: GAIN_COARSE_COREA CoreA CoreB PARAMETER 0x23[7:0] 0x29[7:0] MEDIUM GAIN 0x24[7:0] 0x2A[7:0] FINE GAIN Steps 256 256 –Full Scale (0x00) -2% -0.20% Mid–Scale (0x80) 0.00% 0.00% +Full Scale (0xFF) +2% +0.2% Nominal Step Size 0.016% 0.0016% ADDRESS 0X25: MODES Two distinct reduced power modes can be selected. By default, the tri-level NAPSLP pin can select normal operation, nap or sleep modes (refer to“Nap/Sleep” on page 19). This functionality can be overridden and controlled through the SPI. This register is not changed by a Soft Reset. TABLE 10. POWER-DOWN CONTROL VALUE 0x25[2:0] POWER DOWN MODE 000 Pin Control 001 Normal Operation 010 Nap Mode 100 Sleep Mode ADDRESS 0X23: GAIN_MEDIUM_COREA ADDRESS 0X26: OFFSET_COARSE_COREB ADDRESS 0X24: GAIN_FINE_COREA ADDRESS 0X27: OFFSET_FINE_COREB Gain of the ADC core can be adjusted in coarse, medium and fine steps. Coarse gain is a 4-bit adjustment while medium and fine are 8-bit. Multiple Coarse Gain Bits can be set for a total adjustment range of ±4.2%. (‘0011’ ≅ -4.2% and ‘1100’ ≅ +4.2%). It is recommended to use one of the coarse gain settings (-4.2%, -2.8%, -1.4%, 0, 1.4%, 2.8%, 4.2%) and fine-tune the gain using the registers at 0x0023 and 0x24. The input offset of ADC CoreB can be adjusted in fine and coarse steps in the same way that offset for CoreB can be adjusted. Both adjustments are made via an 8-bit word as detailed in Table 7. The data format is two’s complement. Bit 0 in register 0xFE must be set high to enable updates written to 0x26 and 0x27 to be used by the ADC (see description for 0xFE). The default value of each register will be the result of the self-calibration after initial power-up. If a register is to be incremented or decremented, the user should first read the register value then write the incremented or decremented value back to the same register. Bit 0 in register 0xFE must be set high 28 The default value of each register will be the result of the self-calibration after initial power-up. If a register is to be incremented or decremented, the user should first read the register value then write the incremented or decremented value back to the same register. FN8302.0 May 1, 2012 ISLA222S ADDRESS 0X28: GAIN_COARSE_COREB TABLE 12. OUTPUT FORMAT CONTROL ADDRESS 0X29: GAIN_MEDIUM_COREB ADDRESS 0X2A: GAIN_FINE_COREB Gain of ADC CoreB can be adjusted in coarse, medium and fine steps in the same way that CoreA can be adjusted. Coarse gain is a 4-bit adjustment while medium and fine are 8-bit. Multiple Coarse Gain Bits can be set for a total adjustment range of ±4.2%. Bit 0 in register 0xFE must be set high to enable updates written to 0x29 and 0x2A to be used by the ADC (see description for 0xFE). VALUE 0x73[2:0] OUTPUT FORMAT 000 Two’s Complement (Default) 010 Gray Code 100 Offset Binary ADDRESS 0X74: OUTPUT_MODE_B Bit 6 DLL Range Global Device Configuration/Control This bit sets the DLL operating range to fast (default) or slow. ADDRESS 0X71: PHASE_SLIP Internal clock signals are generated by a delay-locked loop (DLL), which has a finite operating range. Table 13 shows the allowable sample rate ranges for the slow and fast settings. When using the clock_divide feature, the sample clock edge that the ADC uses to sample the analog input signal can be one of several different edges on the incoming higher frequency sample clock. For example, in clock_divide = 2 mode, every other incoming sample clock edge gets used by the ADC to sample the analog input. The phase_slip feature allows the system to control which edge of the incoming sample clock signals gets used to cause the sampling event, by “slipping” the sampling event by one input clock period each time phase_slip is asserted. The clkdivrst feature can work in conjunction with phase_slip. After well-timed assertion of the clkdivrst signal (via overloading on the SYNC inputs), the sampling edge position with respect to the incoming clock rate will have been reset, allowing the system to “slip” whatever desired number of incoming clock periods from a known state. ADDRESS 0X72: CLOCK_DIVIDE The ADC has a selectable clock divider that can be set to divide by two or one (no division). By default, the tri-level CLKDIV pin selects the divisor. This functionality can be overridden and controlled through the SPI, as shown in Table 11. This register is not changed by a Soft Reset. TABLE 11. CLOCK DIVIDER SELECTION VALUE 0x72[2:0] CLOCK DIVIDER 000 Pin Control 001 Divide by 1 010 Divide by 2 other Not Allowed ADDRESS 0X73: OUTPUT_MODE_A The output_mode_A register controls the logical coding of the sample data. Data can be coded in three possible formats: two’s complement(default), Gray code or offset binary. See Table 12. This register is not changed by a Soft Reset. 29 TABLE 13. DLL RANGES DLL RANGE MIN MAX UNIT Slow 40 100 MSPS Fast 80 250 MSPS ADDRESS 0X77: SYNC_FUNCTION BIT 0 CLKDIVRST This bit controls the functionality of the SYNCP, SYNCN pins on this device. By default, this bit equals ‘0’, which means that the functionality of the SYNCP, SYNCN pins is the JESD204 SYNC. Setting this bit equal to ‘1’ modifies the functionality of the SYNCP, SYNCN pins to be clkdivrst, which is a synchronous divider reset on all internal dividers in the device. Usage of this clkdivrst functionality is required to support multi-chip time alignment and deterministic latency for devices that use interleaved product configurations (ISLA214S50 and ISLA214S35), and for any other product configuration that uses clkdiv > 1. In both states, the setup and hold times with respect to the sample clock remain the same. Contact Intersil sales support for more details. ADDRESS 0XB6: CALIBRATION STATUS The LSB at address 0xB6 can be read to determine calibration status. The bit is ‘0’ during calibration and goes to a logic ‘1’ when calibration is complete. This register is unique in that it can be read after POR at calibration, unlike the other registers on chip, which can’t be read until calibration is complete. DEVICE TEST The device can produce preset or user defined patterns on the digital outputs to facilitate in-situ testing. A user can pick from preset built-in patterns by writing to the output test mode field [7:4] at 0xC0 or user defined patterns by writing to the user test mode field [2:0] at 0xC0. The user defined patterns should be loaded at address space 0xC1 through 0xD0, see the “SPI Memory Map” on page 33 for more detail. The test mode is enabled asynchronously to the sample clock, therefore several sample clock cycles may elapse before the data is present on the output bus. FN8302.0 May 1, 2012 ISLA222S ADDRESS 0xDF - 0xF3: JESD204 REGISTERS ADDRESS 0XC0: TEST_IO Bits 7:4 Output Test Mode These bits set the test mode according to the description in “SPI Memory Map” on page 33. Bits 2:0 User Test Mode The three LSBs in this register determine the test pattern in combination with registers 0xC1 through 0xD0. Refer to the “SPI Memory Map” on page 33. ADDRESS 0XC1: USER_PATT1_LSB ADDRESS 0XC2: USER_PATT1_MSB Address 0xDF-0xEE: JESD204 Parameter INTERFACE This set of registers controls the JESD204 transmitter configuration. By programming these parameters, the system can select between efficient and simple packing, select the number of powered up SERDES lanes, choose the ADC resolution transmitted, and so on. The JESD204 parameters for standard dual channel products are shown in Table 4. This is a small subset of the total number of configurations supported; contact Intersil sales support for details. These registers define the lower and upper eight bits, respectively, of the user-defined pattern 3. 0xE0 through 0xED are the JESD204 parameter registers. These parameters are written to set the transport layer mapping of the JESD204 transmitter in this product family. These registers can be written to shift between efficient and simple packing, to enable or bypass scrambling, and to reduce the number of powered up lanes used in the link. Each speed graded product allows downgrading of the JESD204 link (such as reducing the number of lanes, reducing the converter resolution, etc), but not upgrading. These parameters are communicated on every lane of the link during the 2nd multi-frame of the initial lane alignment sequence, and therefore can be used by a generic JESD204 receiver the supports the given configuration. See the JESD204 specification for additional information on how these registers are used in a JESD204 system, including encoding rules. ADDRESS 0XC7: USER_PATT4_LSB ADDRESS 0XDF: JESD204_UPDATE_CONFIG_START ADDRESS 0XC8: USER_PATT4_MSB Bit 0 update_start These registers define the lower and upper eight bits, respectively, of the user-defined pattern 4. This self-resetting bit is used to indicate that some or all the JESD204 parameters (addresses 0xE0 through 0xED) are going to be written. Writing a ‘1’ to this bit will hold the JESD204 PLL and transmitter in a reset state while these parameters are written, because these parameters can affect the transmitter’s dynamic behavior (such as modifying the PLL’s frequency multiplication). The bit will automatically reset to a ‘0’ once a ‘1’ is written to address 0xEE Bit[0] “update_config W1TC”. The recommended sequence for modifying the JESD204 transmitter is: These registers define the lower and upper eight bits, respectively, of the user-defined pattern 1. ADDRESS 0XC3: USER_PATT2_LSB ADDRESS 0XC4: USER_PATT2_MSB These registers define the lower and upper eight bits, respectively, of the user-defined pattern 2 ADDRESS 0XC5: USER_PATT3_LSB ADDRESS 0XC6: USER_PATT3_MSB ADDRESS 0XC9: USER_PATT5_LSB ADDRESS 0XCA: USER_PATT5_MSB These registers define the lower and upper eight bits, respectively, of the user-defined pattern 5. ADDRESS 0XCB: USER_PATT6_LSB ADDRESS 0XCC: USER_PATT6_MSB 1. Write a ‘1’ to 0xDF Bit[0] These registers define the lower and upper eight bits, respectively, of the user-defined pattern 6. 2. Write some or all modified values to 0xE0 through 0xEC ADDRESS 0XCD: USER_PATT7_LSB 3. Write a ‘1’ to 0xEE Bit[0]. Note: 0xDF Bit[0] and 0xEE Bit[0] will automatically be reset to a ‘0’ once configuration has been applied to the circuitry. ADDRESS 0XCE: USER_PATT7_MSB ADDRESS 0XE0: JESD204_CONFIG_0 These registers define the lower and upper eight bits, respectively, of the user-defined pattern 7. Bits 7:0 “DID”, JESD204 Device ID number. ADDRESS 0XCF: USER_PATT8_LSB ADDRESS 0XD0: USER_PATT8_MSB These registers define the lower and upper eight bits, respectively, of the user-defined pattern 8. 30 ADDRESS 0XE1: JESD204_CONFIG_1 Bits 3:0 “BID”, JESD204 Bank ID. ADDRESS 0XE2: JESD204_CONFIG_2 Bits 4:0 “LID” JESD204 Lane ID. FN8302.0 May 1, 2012 ISLA222S ADDRESS 0XE3: JESD204_CONFIG_3 ADDRESS 0XEF: JESD204_PLL_MONITOR_RESET Bit 7 “SCR”, JESD204 SCR controls if scrambling across the SERDES lane(s) is enabled (‘1’ means enabled). Bit 0 “pll_lock_mon_rst”, This self resetting register resets the state of the 0xF0 Bit[0] “latched_pll_lockn” bit. The purpose of this pair of bits is as a debugging feature to the system designer. The “latched_pll_lockn” bit indicates if the JESD204 transmitter PLL inside the device has at any time lost lock since the last ‘1’ was written to the “pll_lock_mon_rst” bit. This can be used to help identify the source of intermittent link lost errors in the system. Bits 4:0 “L”, JESD204 L is the number of SERDES lanes in the link. Address 0xE4: jesd204_config_4 Bits 7:0 “F”, JESD204 Number of octets per frame period. Address 0xE5: jesd204_config_5 Bits 4:0 “K” JESD204 Number of frame periods per multi-frame period. This product family supports the full programmable range of K (decimal 0 through 31), although note that the JESD204 standard dictates a minimum number for this parameter that is configuration dependent. Address 0xE6: jesd204_config_6 Bits 7:0 “M” JESD204 Number of converters per device. Address 0xE7: jesd204_config_7 Bits 7:6 “CS”, JESD204 CS is the number of control bits per sample (Always ‘0’ for this product family). Bits 4:0 “N”, JESD204 N is the converter resolution. Address 0xE8: jesd204_config_8 Bits 4:0 “N’”, JESD204 N’ is the total number of bits per sample. Address 0xE9: jesd204_config_9 Bits 4:0 “S”, JESD204 Number of samples per converter per frame cycle. Address 0xEa: jesd204_config_10 Bit 7 “HD”, JESD204 HD indicates if a converter’s sample can be split across multiple lanes in the link (always ‘0’ for this product family). Bits 4:0 “CF”, JESD204 CF is the number of control fames per frame clock (always ‘0’ for this product family). Address 0xEb: jesd204_config_11 Bits 7:0 “RES1”, JESD204 reserved for future use. Address 0xEc: jesd204_config_12 Bits 7:0 “RES2”, JESD204 reserved for future use. Address 0xEd: jesd204_config_13 Bits 7:0 “FCHK” JESD204 checksum (unsigned sum MOD 256) of all the other JESD204 parameter register values. This is a readonly register, as the checksum is calculated by the device. ADDRESS 0XEE: JESD204_UPDATE_CONFIG_COMPLETE Bit 0 update_complete This self-resetting bit is used to indicate that all the modifications to the JESD204 parameters are complete. 31 ADDRESS 0XF0: JESD204_STATUS Bit 2 “op_cfg_wrong” indicates if the JESD204 parameters (registers 0xE0 through 0xED) are supported by the JESD204 transmitter (a ‘1’ indicates they are not supported, a ‘0’ indicates they are supported). Bit 1“pll_lockn” indicates if the JESD204 transmitter PLL is currently locked (a ‘1’ indicates it is not locked, a ‘0’ indicates it is locked). Bit 0 “latched_pll_lockn” indicates if the JESD204 transmitter PLL has lost lock since the last assertion of the “pll_lock_mon_rst” (see register 0xEF description for more information). ADDRESS 0XF1: JESD204_SYNC Bit 0 “sync_req” this register provides a SPI-programmable interface that can be used to assert and de-assert the JESD204 SYNC~ functionality. Certain systems may benefit from the elimination of SYNC~ as a separate board-level LVDS signal (and the power, PCB space, and pins it consumes), and these systems can use this register to functionally assert and de-assert SYNC~. For this bit to have any effect, a ‘1’ must have previously been written to the SYNC_FUNCTION (Address 0x77, bit 0). A ‘1’ written to this bit will result in behavior identical to the assertion of SYNC~ (comma character generation), and ‘0’ will result in the behavior identical to the de-assertion of SYNC~ (initial lane alignment sequence followed by converter data). Usage of this SPI SYNC~ capability may compromise the system’s ability to perform multi-chip time alignment, as the SYNC~ asserted to de-asserted transition using this register is not well timed with respect to sample clock. ADDRESS 0XF2: JESD204_TRANS_PAT_CONFIG Bit 0 “no_mf_lane_sync”, By default, this device family assumes that both sides of the link support lane synchronization. As per the JESD204 rev A standard, in this case continuous frame alignment monitoring via character substitution (section 5.3.3.4) is modified such that a different control character is substituted when the octet reoccurrence happens at the end of a multi-frame. This behavior occurs when bit 0 is ‘0’ (the power on default). Writing a ‘1’ to bit 0 will inform the JESD204 transmitter than the receiving device does not support lane synchronization, and therefore the transmitter will no longer substitute this different control character when reoccurrence of octets occurs at the end of a multi-frame. Bit 1 “trans_pat_max_len” There is some ambiguity of the proper length of the JESD204 rev A section 5.1.6.2 required transport layer test pattern. Specifically, that the description perhaps should have “max()” in place of “min()” for the equation defining FN8302.0 May 1, 2012 ISLA222S the length of the pattern. Setting bit 1 in this register to a ‘0’ (also the power-on default) and issuing this test pattern by writing to 0xC0 will cause the pattern to assume a “min()” interpretation of the pattern described in section 5.1.6.2. Setting the bit to a ‘1’ will assume a “max()” interpretation of the described pattern. ADDRESS 0XF3: JESD204_CML_POLARITY 0xF3 Bit[2:0]: “TX polarity flip lane x” This register allows the system designer to invert the sense of the SERDES pins on a per lane basis. For example, writing a ‘1’ to Bit[0] causes LANE0N to functionally become LANE0P and LANE0P to become LANE0N. This feature allows the system designer to avoid having to crossover P and N sides of the CML pair on the board to match pin out and layout of the transmitter and receiver. Typically, a trace crossover would require vias, which can degrade the signal integrity of the high-speed SERDES lanes. ADDRESS 0XFE: OFFSET/GAIN_ADJUST_ENABLE Bit 0 at this register must be set high to enable adjustment of offset coarse and fine adjustments (0x20 and 0x21) and gain medium and gain fine adjustments(0x23 and 0x24). It is recommended that new data be written to the offset and gain adjustment registers (0x20, 0x21, 0x23, 0x24) while Bit 0 is a ‘0’. Subsequently, Bit 0 should be set to ‘1’ to allow the values written to the aforementioned registers to be used by the ADC. Bit 0 should be set to a ‘0’ upon completion. 32 FN8302.0 May 1, 2012 ISLA222S Device Config/Control DUT Info SPI Config/Control SPI Memory Map ADDR. (Hex) PARAMETER NAME BIT 7 (MSB) 00 port_config 01 Reserved Reserved 02 burst_end Burst end address [7:0] 03-07 Reserved Reserved BIT 6 BIT 5 BIT 4 BIT 3 SDO Active LSB First Soft Reset BIT 2 BIT 1 BIT 0 (LSB) DEF. VALUE (HEX) Mirror (bit5) Mirror (bit6) Mirror (bit7) 00h 00h 08 chip_id Chip ID # Read only 09 chip_version Chip Version # Read only 0A-0F Reserved Reserved 10-1F Reserved Reserved 20 offset_coarse_CoreA Coarse Offset cal. value 21 offset_fine_CoreA Fine Offset cal. value 22 gain_coarse_CoreA 23 gain_medium_CoreA 24 gain_fine_CoreA 25 modes_CoreA 26 offset_coarse_CoreB 27 offset_fine_CoreB 28 gain_coarse_CoreB Reserved Coarse Gain cal. value Medium Gain cal. value Fine Gain Reserved cal. value Power Down Mode CoreA [2:0] 000 = Pin Control 001 = Normal Operation 010 = Nap 100 = Sleep Other codes = Reserved Coarse Offset cal. value Fine Offset Reserved 00h NOT reset by Soft Reset cal. value Coarse Gain cal. value 29 gain_medium_CoreB Medium Gain cal. value 2A gain_fine_CoreB Fine Gain cal. value 2B modes_CoreB Reserved Power Down Mode CoreB [2:0] 000 = Pin Control 001 = Normal Operation 010 = Nap 100 = Sleep Other codes = Reserved 2C-6F Reserved Reserved 70 skew_diff Differential Skew 71 phase_slip 72 clock_divide Reserved 33 00h NOT reset by Soft Reset 80h Next Clock Edge Clock Divide [2:0] 000 = Pin Control 001 = divide by 1 010 = divide by 2 100 = divide by 4 Other codes = Reserved 00h 00h NOT reset by Soft Reset FN8302.0 May 1, 2012 ISLA222S Device Config/Control SPI Memory Map (Continued) ADDR. (Hex) PARAMETER NAME 73 output_mode_A 74 output_mode_B 75-76 Reserved 77 SYNC_function 78-B5 Reserved B6 cal_status B7-BF Reserved BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) DEF. VALUE (HEX) 00h Output Format [2:0] 000 = Two’s Complement (Default) NOT reset by Soft Reset 010 = Gray Code 100 = Offset Binary Other codes = Reserved 00h NOT reset by Soft Reset DLL Range 0 = Fast 1 = Slow Default=’0 ’ Reserved Clkdivrst Reserved Reserved 34 Calibration Done Read Only FN8302.0 May 1, 2012 ISLA222S SPI Memory Map (Continued) ADDR. (Hex) PARAMETER NAME C0 test_io BIT 7 (MSB) BIT 6 BIT 5 BIT 4 Output Test Mode [7:4] BIT 3 JESD Test Device Test <7:4>=Output Test, <3> = JESD Test JESD Test=0 Output Test = 0x0= Output Test Mode Off. During calibration MSB justified constant output 0xCCCC 0x1 = Midscale adjusted by numeric format 0x2 = Plus full scale, adjusted by numeric format 0x3 = Minus full scale adjusted by numeric format 0x4 = Checkboard output - 0xAAAA, 0x5555 0x5 = reserved 0x6 = reserved 0x7 = 0xFFFF, 0x0000 all on pattern 0x8 = User pattern 8 deep, MSB justified with output 0x9 = reserved 0xA, Count-up ramp 0xB, PRBS-9 0xC, PRBS-15 0xD, PRBS-23 0xE, PRBS-31 0xF = reserved JESD Test=1 Output Test = 0x0 =Link Layer Repeat K28.5+Lane Alignment Sequence 0x1, Link Layer Repeat K28.5 0x2, Link Layer Repeat D21.5 0x3, Link Layer Repeat K28.7 0x4, Link Layer PRBS-7 0x5, Link Layer PRBS-23 0x6, Link Layer All Zeros 0x7, Link Layer All Ones 0x8-0xE, reserved 0xF, JESD204 section 5.1.6.2 Transport Layer Test Pattern BIT 2 BIT 1 BIT 0 (LSB) User Test Mode [2:0] User Test Mode (Single ADC products only) 0 = user pattern 1 only 1 = cycle pattern 1 through 2 2 = cycle pattern 1 through 3 3 = cycle pattern 1 through 4 4 = cycle pattern 1 through 5 5 = cycle pattern 1 through 6 6 = cycle pattern 1 through 7 7 = cycle pattern 1 through 8 User Test Mode (Dual and interleaved ADC products only) 0 = cycle pattern 1 through 2 1 = cycle pattern 1 through 4 2 = cycle pattern 1 through 6 3 = cycle pattern 1 through 8 4 -7 = NA DEF. VALUE (HEX) 00h C1 user_patt1_lsb B7 B6 B5 B4 B3 B2 B1 B0 00h C2 user_patt1_msb B15 B14 B13 B12 B11 B10 B9 B8 00h C3 user_patt2_lsb B7 B6 B5 B4 B3 B2 B1 B0 00h C4 user_patt2_msb B15 B14 B13 B12 B11 B10 B9 B8 00h C5 user_patt3_lsb B7 B6 B5 B4 B3 B2 B1 B0 00h C6 user_patt3_msb B15 B14 B13 B12 B11 B10 B9 B8 00h C7 user_patt4_lsb B7 B6 B5 B4 B3 B2 B1 B0 00h C8 user_patt4_msb B15 B14 B13 B12 B11 B10 B9 B8 00h C9 user_patt5_lsb B7 B6 B5 B4 B3 B2 B1 B0 00h CA user_patt5_msb B15 B14 B13 B12 B11 B10 B9 B8 00h CB user_patt6_lsb B7 B6 B5 B4 B3 B2 B1 B0 00h CC user_patt6_msb B15 B14 B13 B12 B11 B10 B9 B8 00h CD user_patt7_lsb B7 B6 B5 B4 B3 B2 B1 B0 00h CE user_patt7_msb B15 B14 B13 B12 B11 B10 B9 B8 00h CF user_patt8_lsb B7 B6 B5 B4 B3 B2 B1 B0 00h D0 user_patt8_msb B15 B14 B13 B12 B11 B10 B9 B8 00h D1-DE Reserved Reserved 35 FN8302.0 May 1, 2012 ISLA222S SPI Memory Map (Continued) PARAMETER NAME DF JESD204_update_config_star t E0 JESD204_config_0 E1 JESD204_config_1 E2 JESD204_config_2 E3 JESD204_config_3 E4 JESD204_config_4 E5 JESD204_config_5 E6 JESD204_config_6 E7 JESD204_config_7 E8 JESD204_config_8 BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) DEF. VALUE (HEX) update_ start 00h DID (Device ID Number) 00h BID (Bank ID Number) LID (Lane ID Number) SCR L (Number of Lanes per Device) F (Number of Octets per Frame) K (Number of frames per multi-frame) M (Number of Converters per Device) CS (Number of Control bits per Sample) N (Converter Resolution in bits) N’ (Total number of bits per Sample) E9 JESD204_config_9 EA JESD204_config_10 EB JESD204_config_11 RES1 EC JESD204_config_12 RES2 ED JESD204_config_13 FCHK (Checksum) EE JESD204_update_config_com plete update_ complete 00h EF JESD204_PLL_monitor_reset pll_lock_ mon_rst 00h F0 JESD204_status latched_ pll_lockn 00h F1 JESD204_sync F2 JESD204_trans_pat_config F3 JESD204_CML_polarity F4-FD Reserved FE Offset/Gain_Adjust_Enable FF Reserved S (Number of Samples per Converter per Frame) See Description for Default Settings JESD204 Interface ADDR. (Hex) HD CF (Number of Control Words per Frame per Link) op_confg_ pll_lockn wrong sync_req trans_pat_ no_mf_ max_len lane_sync lane_2_ polarity lane_1_ polarity lane_0_ polarity 00h Enable ‘1’=Enable 00h Reserved Reserved 36 FN8302.0 May 1, 2012 ISLA222S Equivalent Circuits AVDD AVDD TO CHARGE PIPELINE INP 600 E3 11k CSAMP 4pF AVDD 18k TO CHARGE PIPELINE INN E2 E1 CLKP AVDD E2 E1 TO CLOCK-PHASE GENERATION AVDD CSAMP 4pF E3 AVDD 18k 11k CLKN FIGURE 60. ANALOG INPUTS AVDD FIGURE 61. CLOCK INPUTS AVDD (20k PULL-UP ON RESETN ONLY) AVDD 75k AVDD OVDD TO SENSE LOGIC 75k 280 INPUT OVDD OVDD 20k INPUT 75k TO 280 75k LOGIC FIGURE 63. DIGITAL INPUTS FIGURE 62. TRI-LEVEL DIGITAL INPUTS OVDD 50 OVDD 50 LANE[2:0]P AVDD OVDD VCM LANE[2:0]N 1.0V DATA + – DATA 16mA FIGURE 64. CML OUTPUTS 37 FIGURE 65. VCM_OUT OUTPUT FN8302.0 May 1, 2012 ISLA222S ADC Evaluation Platform Intersil offers ADC Evaluation platforms which can be used to evaluate any of Intersil’s high speed ADC products. Each platform consists of a FPGA based data capture motherboard and a family of ADC daughtercards. The USB interface and evaluation platform control software allow a user to quickly evaluate the ADC’s performance at a user’s specific application frequency requirements. More information is available at http://www.intersil.com/converters/adc_eval_platform/ Layout Considerations Split Ground and Power Planes Data converters operating at high sampling frequencies require extra care in PC board layout. Many complex board designs benefit from isolating the analog and digital sections. Analog supply and ground planes should be laid out under signal and clock inputs. Locate the digital planes under outputs and logic pins. Grounds should be joined under the chip. used. Tri-level inputs (NAPSLP) accept a floating input as a valid state, and therefore should be biased according to the desired functionality. Definitions Analog Input Bandwidth is the analog input frequency at which the spectral output power at the fundamental frequency (as determined by FFT analysis) is reduced by 3dB from its full-scale low-frequency value. This is also referred to as Full Power Bandwidth. Aperture Delay or Sampling Delay is the time required after the rise of the clock input for the sampling switch to open, at which time the signal is held for conversion. Aperture Jitter is the RMS variation in aperture delay for a set of samples. Clock Duty Cycle is the ratio of the time the clock wave is at logic high to the total time of one clock period. Clock Input Considerations Differential Non-Linearity (DNL) is the deviation of any code width from an ideal 1 LSB step. Use matched transmission lines to the transformer inputs for the analog input and clock signals. Locate transformers and terminations as close to the chip as possible. Effective Number of Bits (ENOB) is an alternate method of specifying Signal to Noise-and-Distortion Ratio (SINAD). In dB, it is calculated as: ENOB = (SINAD - 1.76)/6.02 Exposed Paddle Gain Error is the ratio of the difference between the voltages that cause the lowest and highest code transitions to the full-scale voltage less than 2 LSB. It is typically expressed in percent. The exposed paddle must be electrically connected to analog ground (AVSS) and should be connected to a large copper plane using numerous vias for optimal thermal performance. Bypass and Filtering Bulk capacitors should have low equivalent series resistance. Tantalum is a good choice. For best performance, keep ceramic bypass capacitors very close to device pins, as longer traces between the ceramic bypass capacitors and the device pins will increase inductance, which can result in diminished dynamic performance. Best practices bypassing is especially important on the AVDD and OVDD(PLL) power supply pins. Whenever possible, each supply pin should have its own 0.1uF bypass capacitor. Make sure that connections to ground are direct and low impedance. Avoid forming ground loops. CML Outputs Output traces and connections must be designed for 50Ω (100Ω differential) characteristic impedance. Keep traces direct and short, and minimize bends and vias where possible. Avoid crossing ground and power-plane breaks with signal traces. Keep good clearance (at least 5 trace widths) between the SERDES traces and other signals. Given the speed of these outputs and importance of maintaining an open eye to achieve low BER, signal integrity simulations are recommended, especially when the data lane rate exceeds 3Gbps and/or the trace or cable length between the ADC and the reciever gets larger than 20cm. Unused Inputs Standard logic inputs (RESETN, CSB, SCLK, SDIO, SDO) which will not be operated do not require connection to ensure optimal ADC performance. These inputs can be left floating if they are not 38 I2E The Intersil Interleave Engine. This highly configurable circuitry performs estimates of offset, gain, and sample time skew mismatches between the core converters, and updates analog adjustments for each to minimize interleave spurs. Integral Non-Linearity (INL) is the maximum deviation of the ADC’s transfer function from a best fit line determined by a least squares curve fit of that transfer function, measured in units of LSBs. Least Significant Bit (LSB) is the bit that has the smallest value or weight in a digital word. Its value in terms of input voltage is VFS/(2N - 1) where N is the resolution in bits. Missing Codes are output codes that are skipped and will never appear at the ADC output. These codes cannot be reached with any input value. Most Significant Bit (MSB) is the bit that has the largest value or weight. Pipeline Delay is the number of clock cycles between the initiation of a conversion and the appearance at the output pins of the data. Power Supply Rejection Ratio (PSRR) is the ratio of the observed magnitude of a spur in the ADC FFT, caused by an AC signal superimposed on the power supply voltage. Signal to Noise-and-Distortion (SINAD) is the ratio of the RMS signal amplitude to the RMS sum of all other spectral components below one half the clock frequency, including harmonics but excluding DC. FN8302.0 May 1, 2012 ISLA222S Signal-to-Noise Ratio (without Harmonics) is the ratio of the RMS signal amplitude to the RMS sum of all other spectral components below one-half the sampling frequency, excluding harmonics and DC. Spurious-Free-Dynamic Range (SFDR) is the ratio of the RMS signal amplitude to the RMS value of the largest spurious spectral component. The largest spurious spectral component may or may not be a harmonic. SNR and SINAD are either given in units of dB when the power of the fundamental is used as the reference, or dBFS (dB to full scale) when the converter’s full-scale input power is used as the reference. Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev. DATE REVISION May 1, 2012 FN8302.0 CHANGE Initial Release Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: ISLA222S12, ISLA222S20, ISLA222S25. To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff FITs are available from our website at: http://rel.intersil.com/reports/search.php For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 39 FN8302.0 May 1, 2012 ISLA222S Package Outline Drawing L48.7x7G 48 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 0, 1/10 7.00 6 6 PIN #1 INDEX AREA 4X 5.5 A B 37 PIN 1 INDEX AREA 48 36 1 7.00 44X 0.50 (4X) EXP. DAP 5.70 SQ. 12 25 0.15 24 13 48X 0.40 48x 0.20 4 TOP VIEW BOTTOM VIEW SEE DETAIL "X" 1.00 MAX 0.10 C C 0.08 C SEATING PLANE ( 44X 0 . 5 ) 6 .80 SQ SIDE VIEW 5.70 SQ C 0 . 2 REF 5 ( 48X 0 . 20 ) 0 . 00 MIN. 0 . 05 MAX. ( 48X 0 . 60 ) TYPICAL RECOMMENDED LAND PATTERN DETAIL "X" NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to ASME Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension applies to the metallized terminal and is measured between 0.015mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. 40 FN8302.0 May 1, 2012