KM68V257E/EL, KM68V257EI/ELI CMOS SRAM Document Title 32Kx8 Bit High-Speed CMOS Static RAM (3.3V Operating) Operated at Commercial and Industrial Temperature Range. Revision History Rev. No. History Draft Data Rev. 0.0 Initial Draft Aug. 1. 1998 Preliminary Rev. 1.0 Release to Final Data Sheet 1. Delete Preliminary 2. Delete Data Retention 3. Relex Standby current Item Previous Sep. 7. 1998 Final Isb1 0.3mA Current 0.5mA 2mA Remark Remark L-ver. Normal The attached data sheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right to change the specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions on the parameters of this device. If you have any questions, please contact the SAMSUNG branch office near your office, call or contact Headquarters. -1- Revision 0.0 August 1998 KM68V257E/EL, KM68V257EI/ELI CMOS SRAM 32K x 8 Bit High-Speed CMOS Static RAM (3.3V Operating) FEATURES GENERAL DESCRIPTION • Fast Access Time 12,15,20ns(Max.) • Low Power Dissipation Standby (TTL) : 20mA(Max.) (CMOS) : 2.0mA(Max.) 0.5mA(Max.) L-ver. only Operating KM68V257E - 12 : 70mA(Max.) KM68V257E - 15 : 70mA(Max.) KM68V257E - 20 : 70mA(Max.) • Single 3.3 ±0.3V Power Supply • TTL Compatible Inputs and Outputs • Fully Static Operation - No Clock or Refresh required • Three State Outputs • Standard Pin Configuration KM68V257EJ : 28-SOJ-300 KM68V257ETG : 28-TSOP1-0813, 4F The KM68V257E is a 262,144-bit high-speed Static Random Access Memory organized as 32,768 words by 8 bits. The KM68V257E uses 8 common input and output lines and has an output enable pin which operates faster than address access time at read cycle. The device is fabricated using SAMSUNG′s advanced CMOS process and designed for high-speed circuit technology. It is particularly well suited for use in high-density high-speed system applications. The KM68V257E is packaged in a 300mil 28-pin plastic SOJ or TSOP1 forward. PIN CONFIGURATION(Top View) OE A11 A9 A8 A13 WE Vcc A14 A12 A7 A6 A5 A4 A3 ORDERING INFORMATION KM68V257E -12/15/20 Commercial Temp. KM68V257EI -12/15/20 Industrial Temp. FUNCTIONAL BLOCK DIAGRAM Clk Gen. Pre-Charge-Circuit Row Select A0 A1 A2 A3 A4 A5 A6 A7 A8 I/O1~I/O8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A14 1 28 Vcc A12 2 27 WE A7 3 26 A13 A6 4 25 A8 A5 5 24 A9 A4 6 23 A11 Memory Array 512 Rows 64x8 Columns Data Cont. A3 7 I/O Circuit Column Select CLK Gen. A9 A10 A11 A12 A13 TSOP1 28 27 26 25 24 23 22 21 20 19 18 17 16 15 SOJ A10 CS I/O8 I/O7 I/O6 I/O5 I/O4 Vss I/O3 I/O2 I/O1 A0 A1 A2 22 OE A2 8 21 A10 A1 9 20 CS A0 10 19 I/O8 I/O1 11 18 I/O7 I/O2 12 17 I/O6 I/O3 13 16 I/O5 Vss 14 15 I/O4 PIN FUNCTION A14 Pin Name Pin Function CS A0 - A14 WE WE Write Enable OE CS Chip Select OE Output Enable I/O1 ~ I/O8 -2- Address Inputs Data Inputs/Outputs VCC Power(+3.3V) VSS Ground Revision 0.0 August 1998 KM68V257E/EL, KM68V257EI/ELI CMOS SRAM ABSOLUTE MAXIMUM RATINGS* Parameter Symbol Rating Unit VIN, VOUT -0.5 to 4.6 V Voltage on VCC Supply Relative to VSS VCC -0.5 to 4.6 V Power Dissipation PD 1.0 W Voltage on Any Pin Relative to VSS TSTG -65 to 150 °C Commercial TA 0 to 70 °C Industrial TA -40 to 85 °C Storage Temperature Operating Temperature * Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED DC OPERATING CONDITIONS(TA=0 to 70°C) Parameter Symbol Min Typ Max Unit Supply Voltage VCC 3.0 3.3 3.6 V Ground VSS 0 0 0 V Input High Voltage VIH 2.0 - VCC+0.3** V Input Low Voltage VIL -0.3* - 0.8 V NOTE: The above parameters are also guaranteed at industrial temperature range. * VIL(Min) = -2.0(Pulse Width ≤ 8ns) for I ≤ 20mA ** VIH(Max) = VCC+2.0V(Pulse Width ≤ 8ns) for I ≤ 20mA DC AND OPERATING CHARACTERISTICS(TA=0 to 70°C,VCC=3.3±0.3V, unless otherwise specified) Parameter Symbol Test Conditions Min Max Unit Input Leakage Current ILI VIN = VSS to VCC -2 2 µA Output Leakage Current ILO CS=VIH or OE=VIH or WE=VIL VOUT = VSS to VCC -2 2 µA Operating Current ICC Min. Cycle, 100% Duty CS=VIL, VIN = VIH or VIL, IOUT=0mA 12ns - 70 mA 15ns - 70 20ns Standby Current ISB Min. Cycle, CS=VIH ISB1 f=0MHz, CS≥VCC-0.2V, VIN≥VCC-0.2V or VIN≤0.2V Output Low Voltage Level VOL IOL=8mA Output High Voltage Level VOH IOH=-4mA 70 - 20 mA Normal - 2 mA L-ver - 0.5 - 0.4 V 2.4 - V NOTE: The above parameters are also guaranteed at industrial temperature range. CAPACITANCE*(TA=25°C, f=1.0MHz) Symbol Test Conditions MIN Max Unit Input/Output Capacitance Item CI/O VI/O=0V - 8 pF Input Capacitance CIN VIN=0V - 7 pF * NOTE : Capacitance is sampled and not 100% tested. -3- Revision 0.0 August 1998 KM68V257E/EL, KM68V257EI/ELI CMOS SRAM AC CHARACTERISTICS(TA=0 to 70°C, VCC=3.3±0.3V, unless otherwise noted.) TEST CONDITIONS Parameter Value Input Pulse Levels 0V to 3V Input Rise and Fall Times 3ns Input and Output timing Reference Levels 1.5V Output Loads See below NOTE : The above test conditions are also applied at industrial temperature range. Output Loads(A) Output Loads(B) for tHZ, tLZ, tWHZ, tOW, tOLZ & tOHZ +3.3V RL = 50Ω DOUT 319Ω VL = 1.5V ZO = 50Ω DOUT 30pF* 353Ω 5pF* * Including Scope and Jig Capacitance * Capacitive Load consists of all components of the test environment. READ CYCLE KM68V257E-12 KM68V257E-15 KM68V257E-20 Min Max Min Max Min Max tRC 12 - 15 - 20 - ns Address Access Time tAA - 12 - 15 - 20 ns Chip Select to Output tCO - 12 - 15 - 20 ns Output Enable to Valid Output tOE - 6 - 7 - 8 ns Chip Enable to Low-Z Output tLZ 3 - 3 - 3 - ns Output Enable to Low-Z Output tOLZ 0 - 0 - 0 - ns Chip Disable to High-Z Output tHZ 0 6 0 7 0 8 ns Output Disable to High-Z Output tOHZ 0 6 0 7 0 8 ns Output Hold from Address Change tOH 3 - 3 - 3 - ns Chip Selection to Power Up Time tPU 0 - 0 - 0 - ns Chip Selection to Power DownTime tPD - 12 - 15 - 20 ns Parameter Read Cycle Time Symbol Unit NOTE : The above parameters are also guaranteed at industrial temperature range. -4- Revision 0.0 August 1998 KM68V257E/EL, KM68V257EI/ELI CMOS SRAM WRITE CYCLE Parameter Symbol KM68V257E-12 KM68V257E-15 KM68V257E-20 Min Max Min Min Max Max Unit Write Cycle Time tWC 12 - 15 - 20 - ns Chip Select to End of Write tCW 8 - 9 - 10 - ns Address Setup Time tAS 0 - 0 - 0 - ns Address Valid to End of Write tAW 8 - 9 - 10 - ns Write Pulse Width(OE High) tWP 8 - 9 - 10 - ns Write Pulse Width(OE Low) tWP1 12 - 15 - 20 - ns Write Recovery Time tWR 0 - 0 - 0 - ns Write to Output High-Z tWHZ 0 6 0 7 0 8 ns Data to Write Time Overlap tDW 6 - 7 - 8 - ns Data Hold from Write Time tDH 0 - 0 - 0 - ns End Write to Output Low-Z tOW 0 - 0 - 0 - ns NOTE : The above parameters are also guaranteed at industrial temperature range. TIMMING DIAGRAMS TIMING WAVEFORM OF READ CYCLE(1) (Address Controlled, CS=OE=VIL, WE=VIH) tRC Address tAA tOH Data Out Valid Data Previous Valid Data TIMING WAVEFORM OF READ CYCLE(2) (WE=VIH) tRC Address tAA tCO CS tHZ(3,4,5) tOHZ tOE OE tOLZ tOH tLZ(4,5) Data out Valid Data VCC ICC Current ISB tPU tPD 50% 50% -5- Revision 0.0 August 1998 KM68V257E/EL, KM68V257EI/ELI CMOS SRAM NOTES(READ CYCLE) 1. WE is high for read cycle. 2. All read cycle timing is referenced from the last valid address to the first transition address. 3. tHZ and tOHZ are defined as the time at which the outputs achieve the open circuit condition and are not referenced to VOH or VOL levels. 4. At any given temperature and voltage condition, tHZ(Max.) is less than tLZ(Min.) both for a given device and from device to device. 5. Transition is measured ±200mV from steady state voltage with Load(B). This parameter is sampled and not 100% tested. 6. Device is continuously selected with CS=VIL. 7. Address valid prior to coincident with CS transition low. 8. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycle. TIMING WAVEFORM OF WRITE CYCLE(1) (OE= Clock) tWC Address tWR(5) tAW OE tCW(3) CS tWP(2) tAS(4) WE tDW Data in High-Z tDH Valid Data tOHZ(6) High-Z(8) Data out TIMING WAVEFORM OF WRITE CYCLE(2) (OE=Low Fixed) tWC Address tWR(5) tAW tCW(3) CS tAS(4) tWP1(2) WE tDW Data in High-Z tDH Valid Data tWHZ(6) tOW (10) (9) High-Z(8) Data out -6- Revision 0.0 August 1998 KM68V257E/EL, KM68V257EI/ELI CMOS SRAM TIMING WAVEFORM OF WRITE CYCLE(3) (CS = Controlled) tWC Address tAW tWR(5) tCW(3) CS tWP(2) tAS(4) WE tDW High-Z Data in Valid Data tLZ High-Z tWHZ(6) High-Z(8) High-Z Data out tDH NOTES(WRITE CYCLE) 1. All write cycle timing is referenced from the last valid address to the first transition address. 2. A write occurs during the overlap of a low CS and WE. A write begins at the latest transition CS going low and WE going low ; A write ends at the earliest transition CS going high or WE going high. tWP is measured from the beginning of write to the end of write. 3. tCW is measured from the later of CS going low to end of write. 4. tAS is measured from the address valid to the beginning of write. 5. tWR is measured from the end of write to the address change. tWR applied in case a write ends as CS or WE going high. 6. If OE, CS and WE are in the Read Mode during this period, the I/O pins are in the output low-Z state. Inputs of opposite phase of the output must not be applied because bus contention can occur. 7. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycle. 8. If CS goes low simultaneously with WE going or after WE going low, the outputs remain high impedance state. 9. Dout is the read data of the new address. 10. When CS is low : I/O pins are in the output state. The input signals in the opposite phase leading to the output should not be applied. FUNCTIONAL DESCRIPTION CS WE OE Mode I/O Pin Supply Current H X X* Not Select High-Z ISB, ISB1 L H H Output Disable High-Z ICC L H L Read DOUT ICC L L X Write DIN ICC * NOTE : X means Don′t Care. -7- Revision 0.0 August 1998 KM68V257E/EL, KM68V257EI/ELI CMOS SRAM PACKAGE DIMENSIONS Units:millimeters/Inches 28-SOJ-300 #28 7.62 0.300 #15 8.51 ±0.12 0.335 ±0.005 6.86 ±0.25 0.270 ±0.010 +0.10 -0.05 0.20 #1 0.008+0.004 -0.002 #14 0.69 MIN 0.027 18.82 MAX 0.741 18.41 ±0.12 0.725 ±0.005 ( 1.30 ) 0.051 ( 1.30 ) 0.051 0.43 ( 0.95 ) 0.0375 +0.10 -0.05 0.017 +0.004 -0.002 1.27 0.050 0.71 3.76 MAX 0.148 0.10 0.004MAX +0.10 -0.05 0.028+0.004 -0.002 28-TSOP1-0813.4F 0.10 MAX 0.004 MAX Units:millimeters/Inches 13.40 ±0.20 0.528 ±0.008 #28 #14 #15 ( 8.40 0.331 MAX #1 0.55 0.0217 0.25 0.010 TYP 0.425 ) 0.017 8.00 0.315 +0.10 -0.05 0.008 +0.004 -0.002 0.20 1.00 ±0.10 0.039 ±0.004 11.80 ±0.10 0.465 ±0.004 0.15 0.006 +0.10 -0.05 +0.004 -0.002 1.20 0.047 MAX 0.05 0.002 MIN 0~8° 0.45 ~0.75 0.018 ~0.030 ( -8- 0.50 ) 0.020 Revision 0.0 August 1998