LC201V02 Liquid Crystal Display Product Specification SPECIFICATION FOR APPROVAL ( ? ) Preliminary Specification ( ) Final Specification Title 20.1” VGA TFT LCD BUYER General SUPPLIER LG.Philips LCD Co., Ltd. MODEL - *MODEL LC201V02 SUFFIX A3 *When you obtain standard approval, please use the above model name without suffix APPROVED BY SIGNATURE DATE / APPROVED BY SIGNATURE DATE S.W Lee / G.Manager REVIEWED BY / J.T Kim / Manager PREPARED BY / J.K Choi / Engineer Please return 1 copy for your confirmation with your signature and comments. Ver. 0.1 Jan. 17, 2003 MNT/TV Products Engineering Dept. LG. Philips LCD Co., Ltd 1 / 26 LC201V02 Liquid Crystal Display Product Specification Contents No ITEM Page COVER 1 CONTENTS 2 RECORD OF REVISIONS 3 1 GENERAL DESCRIPTION 4 2 ABSOLUTE MAXIMUM RATINGS 5 3 ELECTRICAL SPECIFICATIONS 6 3-1 ELECTRICAL CHARACTREISTICS 6 3-2 INTERFACE CONNECTIONS 9 3-3 SIGNAL TIMING SPECIFICATIONS 11 3-4 SIGNAL TIMING WAVEFORMS 12 3-5 COLOR INPUT DATA REFERNECE 13 3-6 POWER SEQUENCE 14 4 OPTICAL SFECIFICATIONS 15 5 MECHANICAL CHARACTERISTICS 19 6 RELIABILITY 22 7 INTERNATIONAL STANDARDS 23 7-1 SAFETY 23 7-2 EMC 23 PACKING 24 8-1 DESIGNATION OF LOT MARK 24 8-2 PACKING FORM 24 PRECAUTIONS 25 26 8 9 Ver. 0.1 Jan. 17, 2003 2 / 26 LC201V02 Liquid Crystal Display Product Specification RECORD OF REVISIONS Revision No Revision Date Page 0.0 Dec.05.2002 - 0.1 Feb.17.2003 4/26 Filled Power Consumption 6/26 Filled Power consumption 15/26 Changed Contrast Ratio,Color Coordinates,Viewing Angle revision 16/26 Filled Table 11. Gamma scale Specification 20/26 Changed Mechanical drawing of LCD 21/26 Changed Mechanical drawing of LCD 23/26 Added 7-1) Safety d) 25/26 Added 9-2. OPERATING PRECAUTIONS 9) Ver. 0.1 DESCRIPTION Preliminary Specification Jan. 17, 2003 3 / 26 LC201V02 Liquid Crystal Display Product Specification 1. General Description LC201V02 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode. It has a 20.1 inch diagonally measured active display area with VGA resolution (480 vertical by 640 horizontal pixel array) Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus, a palette of more than 16,777,216 colors. It has been designed to apply the 8Bit parallel CMOS interface. It is intended to support LCD TV, PCTV where high brightness, wide viewing angle, high color saturation, and high color are important. CN2 CN3 Lamp Ass’y 3 Lamps / @21mA Gamma Reference Circuit Column Driver Circuit CN4 CN5 User Connector CN1 Control Circuit Block +12V Power Block Row Driver Circuit R[0:7], G[0:7], B[0:7] Dclk, Hsync. Vsync.,DE TFT-LCD 640XRGBX480 Vcom Vgh Vgl 3 Lamps / @21mA Lamp Ass’y’ General Features Active Screen Size 20.1 inches(510.54mm) diagonal Outline Dimension 432(H) x 331.5(V) x 25.0(D) mm(Typ.) Pixel Pitch 0.6375mm x 0.6375mm Pixel Format 640 horiz. By 480 vert.. Pixels RGB stripe arrangement Color Depth 8-bits,16,777,216 colors Luminance, White 450 cd/m2 (Center 1 point (Typ.)) Viewing Angle (CR>10) Viewing Angle Free [R/L 176(Typ.), U/D 176(Typ.)] Power Consumption Total 32.03 Watt(Typ.),(1.79Watt@ VLCD,30.24Watt@450cd/[LAMP=7mA]) Weight 3,200 g (Typ.) Display Operating Mode Transmissive mode, normally black Surface Treatment Hard coating(3H) & Anti-glare treatment of the front polarizer Ver. 0.1 Jan. 17, 2003 4 / 26 LC201V02 Liquid Crystal Display Product Specification 2. Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. Table 1. ABSOLUTE MAXIMUM RATINGS Values Parameter Symbol Units Min Max Notes Power Input Voltage VLCD -0.3 +14.0 Vdc Operating Temperature TOP 0 50 °C 1 Storage Temperature TST -20 60 °C 1 Operating Ambient Humidity HOP 10 90 %RH 1 Storage Humidity HST 10 90 %RH 1 Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 °C Max, and no condensation of water. Dry Bulb Temperature [? ] Ver. 0.1 Jan. 17, 2003 5 / 26 LC201V02 Liquid Crystal Display Product Specification 3. Electrical Specifications 3-1. Electrical Characteristics It requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input power for the CCFL /Backlight, is typically generated by an inverter. The inverter is an external unit to the LCDs. Table 2_1. ELECTRICAL CHARACTERISTICS Parameter Values Symbol Unit Notes Min Typ Max 11.4 12.0 12.6 Vdc - 149 172 mA 1 - 178 205 mA 2 MODULE : Power Supply Input Voltage VLCD Power Supply Input Current ILCD Power Consumption PLCD - 1.79 2.07 Watt 1 Rush current IRUSH - - 3.0 A 3 Note : 1. The specified current and power consumption are under the VLCD=12.0V, 25 ± 2°C,fV=60Hz condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency. 2. The current is specified at the maximum current pattern below 3. The duration of rush current is about 2ms and rising time of power Input is 1ms(min.). Maximum current pattern White : 255Gray Black : 0Gray RGBRGBRGBRGB (255)(0)(255)(0)(255)(0)(255)(0)(255)(0)(255)(0) (0)(255)(0)(255)(0)(255)(0)(255)(0)(255)(0)(255) RGBRGBRGBRGB Sub 1 dot pattern [ 255 0 255 ] / [ 0 255 0 ] Mosaic Pattern(8 x 6) Ver. 0.1 Jan. 17, 2003 6 / 26 LC201V02 Liquid Crystal Display Product Specification Table 2_2. ELECTRICAL CHARACTERISTICS Parameter Values Symbol Min Typ Max Unit Notes LAMP : Operating Voltage VBL 700(7.5mA) 720(7mA) 825(3mA) VRMS 1, 2 Operating Current IBL 3.0 7.0 7.5 mARMS 1 Established Starting Voltage Vs at 25 °C 1,100 VRMS at 0 °C 1,430 VRMS 60 kHz 4 3 Min 1, 5 33.27 Watt 6 Hrs 1, 7 Operating Frequency fBL Discharge Stabilization Time Ts Power Consumption PBL Life Time 1, 3 40 50 30.24 50,000 Note : The design of the inverter must have specifications for the lamp in LCD Assembly. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD– Assembly should be operated in the same condition as installed in you instrument. ? Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter has abnormal action. Because leakage current is occurred between lamp wire and conducting tape. 1. Specified values are for a single lamp. 2. Operating voltage is measured at 25 ± 2°C. The variance of the voltage is ± 10%. 3. The voltage above VS should be applied to the lamps for more than 1 second for start-up. (Inverter open voltage must be more than lamp starting voltage.) Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current. 4. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. 5. Let’s define the brightness of the lamp after being lighted for 5 minutes as 100%. TS is the time required for the brightness of the center of the lamp to be not less than 95%. 6. The lamp power consumption shown above does not include loss of external inverter. The used lamp current is the lamp typical current. (PBL = VBL x IBL x NLamp ) 7. The life is determined as the time at which brightness of the lamp is 50% compared to that of initial value at the typical lamp current on condition of continuous operating at 25 ± 2°C. Ver. 0.1 Jan. 17, 2003 7 / 26 LC201V02 Liquid Crystal Display Product Specification 8. The output of the inverter must have symmetrical(negative and positive) voltage waveform and symmetrical current waveform (Unsymmetrical ratio is less than 10%). Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. It shall help increase the lamp lifetime and reduce leakage current. a. The asymmetry rate of the inverter waveform should be less than 10%. b. The distortion rate of the waveform should be within v2 ±10%. * Inverter output waveform had better be more similar to ideal sine wave. * Asymmetry rate: Ip |Ip–I –p | / Irms x 100% * Distortion rate I -p I p (or I –p) / Irms 9. The inverter which is combined with this LCM, is highly recommended to connect coupling(ballast) condenser at the high voltage output side. When you use the inverter which has not coupling(ballast) condenser, it may cause abnormal lamp lighting because of biased mercury as time goes. 10.In case of edgy type back light with over 4 parallel lamps, input current and voltage wave form should be synchronized Ver. 0.1 Jan. 17, 2003 8 / 26 LC201V02 Liquid Crystal Display Product Specification 3-2. Interface Connections - LCD Connector(CN1):DF9B-41P-1V (Manufactured by Hirose) or Equivalent - Mating Connector : DF9B-41S-1V (Manufactured by Hirose) or Equivalent Table 3. MODULE CONNECTOR(CN1) PIN CONFIGURATION Pin No Symbol Description Pin No Symbol Description 1 RBF NC 1) 21 G4 2 DCLK Dot Clock 22 GND 3 GND System Ground 2) 23 G5 4 Hsync Horizontal Sync 24 G6 5 Vsync Vertical Sync 25 G7 Green Data(MSB) 6 GND 26 B0 Blue Data(LSB) 7 R0 27 GND System Ground 8 R1 28 B1 9 R2 29 B2 10 R3 30 B3 11 R4 31 B4 12 GND 32 GND 13 R5 33 B5 14 R6 34 B6 15 R7 Red Data(MSB) 35 B7 Blue Data(MSB) 16 G0 Green Data(LSB) 36 GND System Ground 17 GND System Ground 37 DE Data Enable 18 G1 38 GND System Ground 19 G2 39 VLCD Power input(+12.0V) 20 G3 40 VLCD Power input(+12.0V) 41 VLCD Power input(+12.0V) Red Data(LSB) System Ground System Ground System Ground 1 41 Rear view of LCM 40 2 Note: 1. NC: No Connection. 2. All GND(ground) pins should be connected together and to Vss which should also be connected to the LCD’s metal frame. 3. All VLCD (power input) pins should be connected together. Ver. 0.1 Jan. 17, 2003 9 / 26 LC201V02 Liquid Crystal Display Product Specification Table 4. BACKLIGHT CONNECTOR PIN CONFIGURATION(CN2,CN3,CN4,CN5) The backlight interface connector is a model BHSR-02VS-1(CN3/CN4) and BHR-05VS-1(CN2/CN5) manufactured by JST. The mating connector part number are SM02B-BHSS-1-TB(2pin), SM04(9-E2)BBHS-1-TB(5pin) or equivalent. The pin configuration for the connector is shown in the table below. No CN2 CN3 CN4 CN5 Pin Symbol 1 HV Power supply for lamp 1(High voltage side) - Gray 1 2 HV Power supply for lamp 2(High voltage side) – Sky Blue 1 3 NC NC 4 LV Power supply for lamp 1(Low voltage side) - Black 2 5 LV Power supply for lamp 2(Low voltage side) – Dark Blue 2 1 HV Power supply for lamp 3(High voltage side) - White 1 2 LV Power supply for lamp 3(Low voltage side) - White 2 1 HV Power supply for lamp 4(High voltage side) - White 1 2 LV Power supply for lamp 4(Low voltage side) - White 2 1 HV Power supply for lamp 6(High voltage side) - Gray 1 2 HV Power supply for lamp 5(High voltage side) - Sky Blue 1 3 NC NC 4 LV Power supply for lamp 6(Low voltage side) - Black 2 5 LV Power supply for lamp 5(Low voltage side) - Dark Blue 2 Description Notes Notes: 1. The high voltage power terminal is colored white,sky blue,gray. 2. The low voltage pin color is white,dark blue,black . <BACKLIGHT CONNECTOR DIAGRAM> Up Side Lamp1 CN 2 Lamp 2 Lamp 3 CN 3 Down Side Lamp 4 CN 4 Lamp 5 CN 5 Lamp 6 Ver. 0.1 Jan. 17, 2003 10 / 26 LC201V02 Liquid Crystal Display Product Specification 3-3. Signal Timing Specifications This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications for it’s proper operation. Table 5. Timing Table ITEM Symbol Min Typ Max Unit tCLK 33.3 40 55 ns - 18 25 30 MHz High Duration tWCH 10 - - ns Low Duration tWCL 10 - - ns Period tHP 790 800 850 tCLK Width tWH 16 96 96 tCLK Period tVP 490 525 560 tHP PAL: 47~53Hz Frequency fV 47 60 63 Hz NTSC:57~63Hz Width tWV 2 3 3 tHP Horizontal Valid tHV 640 640 640 Horizontal Back Porch tHBP 16 48 48 Horizontal Front Porch tHFP 16 16 - - 150 - tHP-THV Vertical Valid tVV 480 480 480 Vertical Back Porch tVBP 3 33 33 Vertical Front Porch tVFP 2 9 - - 10 - tVP-tVV DE SET UP TIME tSI 3 - - DE HOLD TIME tHI 3 - - High VrH 0.7Vcc - - Low VrL - - 0.3Vcc Set-up time tSD 3 Hold time tHD 3 Period DCLK Hsync Vsync DE (Data Enable) Frequency Horizontal Blank Vertical Blank Input Voltage Data Note tCLK tHP ns V ns For DCLK Note: Hsync period and Hsync width-active should be even number times of tCLK. If the value is odd number times of tCLK, display control signal can be asynchronous. In order to operate this LCM a Hsync, Vsync and DE (Data Enable) signals should be used. 1. The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rates. 2. Vsync, Hsync should be keep the above specification. 3. Hsync Period, Hsync Width and Horizontal Back Porch should be any times of a character number (8). Ver. 0.1 Jan. 17, 2003 11 / 26 LC201V02 Liquid Crystal Display Product Specification 3-4. Signal Timing Waveforms tHf , tVf tIf , tDf tHr, tVr t Ir , tDr VrH min. Hsync, Vsync, DE, DATA VrLmax. tWCH tCLK tWCL tfCLK trCLK DCLK tSD tCLKL DATA (First/ Second) tHI tHD tSI DE HSYNC tHV VSYNC tHP tWH HSYNC tHFP tHBP DE tVP tWV VSYNC tVBP tVFP DE Ver. 0.1 Jan. 17, 2003 12 / 26 LC201V02 Liquid Crystal Display Product Specification 3-5. Color Input Data Reference The Brightness of each primary color(red,green,blue) is based on the 8-bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input. Table 8. COLOR DATA REFERENCE Input Color Data RED Color GREEN MSB BLUE LSB MSB LSB MSB LSB R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 Basic Color RED GREEN BLUE Ver. 0.1 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Blue (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 RED (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED (001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ... ... ... ... RED (254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GREEN (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GREEN (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ... ... ... ... GREEN (254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 GREEN (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 BLUE (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 BLUE (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ... ... ... ... BLUE (254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 BLUE (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Jan. 17, 2003 13 / 26 LC201V02 Liquid Crystal Display Product Specification 3-6. Power Sequence 90% Power Supply For LCD VLCD 90% 10% 10% 0V T1 T2 T5 T6 Valid Data 10% Interface Signal (Tx) T7 10% 0V T3 T4 Lamp ON Power for LAMP 0FF 0FF Table 9. POWER SEQUENCE Values Parameter Units Min Typ Max T1 0.5 - 10 ms T2 0.5 - 50 ms T3 200 - - ms T4 200 - - ms T5 0.5 - 50 ms T6 - - 100 ms T7 1 - - s Notes : 1. Please avoid floating state of interface signal at invalid period. 2. When the interface signal is invalid, be sure to pull down the power supply for LCD VLCD to 0V. 3. Lamp power must be turn on after power supply for LCD an interface signal are valid. Ver. 0.1 Jan. 17, 2003 14 / 26 LC201V02 Liquid Crystal Display Product Specification 4. Optical Specification Optical characteristics are determined after the unit has been ‘ON’ for 30 minutes in a dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of Φ and θ equal to 0 °. FIG. 1 presents additional information concerning the measurement equipment and method. LCD Module Pritchard 880 or equivalent Optical Stage(x,y) 50cm FIG. 1 Optical Characteristic Measurement Equipment and Method Table 10. OPTICAL CHARACTERISTICS Parameter Symbol Contrast Ratio CR Surface Luminance, white LWH δ WHITE Luminance Variation Response Time Ta= 25°C, VLCD=12.0V, fV=60HzDclk=25MHz, IBL=7mA Values Min Typ Max 280 350 - 380 5P TrR - Decay Time TrD - GREEN Color Coordinates [CIE1931] BLUE WHITE 3 ms 4 15 25 ms 4 degree 5 Ry 0.335 Gx 0.289 Typ -0.03 2 25 0.629 Bx - 15 Rx Gy Notes 1 cd/m2 1.3 Rise Time RED 450 Units 0.583 0.143 By 0.090 Wx 0.289 Wy 0.304 Typ +0.03 Viewing Angle (CR>10) x axis, right(φ=0°) θr 85 88 x axis, left (φ=180°) θl 85 88 y axis, up (φ=90°) θu 85 88 y axis, down (φ=270°) θd 85 88 Gray Scale Ver. 0.1 - Jan. 17, 2003 6 15 / 26 LC201V02 Liquid Crystal Display Product Specification Notes 1. Contrast Ratio(CR) is defined mathematically as : Contrast Ratio = Surface Luminance with all white pixels Surface Luminance with all black pixels It is measured at center point(1). 2. Surface luminance is luminance value at center point (1) across the LCD surface 50cm from the surface with all pixels displaying white. For more information see FIG 2. 3. The variation in surface luminance , δ WHITE is defined as : δ WHITE(5P) = Maximum(Lon1,Lon2, Lon3, ...... , Lon5) / Minimum(Lon1,Lon2, Lon3, ..... , Lon5) Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations 4. Response time is the time required for the display to transition from black to white(Rise Time, Tr R) and from white to black(Decay Time, TrD). For additional information see FIG 3. 5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 4. 6. Gray scale specification Gamma Value is approximately 2.2. For more information see Table 11. Table 11. Gray Scale Specification . Ver. 0.1 Gray Level Luminance [%] (Typ) L0 0.29 L15 0.42 L31 0.95 L47 2.36 L63 4.72 L79 7.82 L95 11.7 L111 16.3 L127 21.8 L143 28.2 L159 35.6 L175 43.5 L191 52.4 L207 62.6 L223 74.1 L239 86.2 L255 100 Jan. 17, 2003 16 / 26 LC201V02 Liquid Crystal Display Product Specification Measuring point for surface luminance & measuring point for luminance variation H A 2 3 A : H / 4 mm B : V / 4 mm H : 408.0 mm V : 306.0 mm @ H,V : Active Area B V 1 4 5 FIG. 2 Measure Point for Luminance The response time is defined as the following figure and shall be measured by switching the input signal for “black” and “white”. TrD TrR 100 90 Optical Response 10 0 black white black FIG. 3 Response Time Ver. 0.1 Jan. 17, 2003 17 / 26 LC201V02 Liquid Crystal Display Product Specification Dimension of viewing angle range Normal F = 180o, Left E Y F = 90o, Up θ φ F = 0o, Right F = 270o, Down FIG. 4 Viewing angle Ver. 0.1 Jan. 17, 2003 18 / 26 LC201V02 Liquid Crystal Display Product Specification 5. Mechanical Characteristics The contents provide general mechanical characteristics. In addition the figures in the next page are detailed mechanical drawing of the LCD. Outline Dimension Horizontal 432.0mm Vertical 331.5mm Depth 25.0 mm Horizontal 413.0 mm Vertical 311.0mm Horizontal 408.0mm Vertical 306.0mm Bezel Area Active Display Area Weight Surface Treatment 3200g (Typ.),3360g(Max) Hard coating(3H) Anti-glare treatment of the front polarizer Notes : Please refer to a mechanic drawing in terms of tolerance at the next page. Ver. 0.1 Jan. 17, 2003 19 / 26 LC201V02 Liquid Crystal Display Product Specification <FRONT VIEW> Ver. 0.1 Jan. 17, 2003 20 / 26 LC201V02 Liquid Crystal Display Product Specification <REAR VIEW> Ver. 0.1 Jan. 17, 2003 21 / 26 LC201V02 Liquid Crystal Display Product Specification 6. Reliability Environment test condition No Test Item Condition 1 High temperature storage test Ta= 60°C 240h 2 Low temperature storage test Ta= -20°C 240h 3 High temperature operation test Ta= 50°C 50%RH 4 Low temperature operation test Ta= 0°C 5 Vibration test (non-operating) Wave form : random Vibration level : 1.0G RMS Bandwidth : 10-500Hz Duration : X,Y,Z, 20 min One time each direction 6 Shock test (non-operating) Shock level : 100G Waveform : half sine wave, 2ms Direction : ±X, ±Y, ±Z One time each direction Altitude 7 Ver. 0.1 240h 240h 0 - 10,000 feet(3048m) 0 - 40,000 feet(12,192m) operating storage / shipment Jan. 17, 2003 22 / 26 LC201V02 Liquid Crystal Display Product Specification 7. International Standards 7-1. Safety a) UL 1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995. Standard for Safety of Information Technology Equipment Including Electrical Business Equipment. b) CAN/CSA C22.2 No. 950-95 Third Edition, Canadian Standards Association, Jan. 28, 1995. Standard for Safety of Information Technology Equipment Including Electrical Business Equipment. c) EN 60950 : 1992+A1: 1993+A2: 1993+A3: 1995+A4: 1997+A11: 1997 IEC 950 : 1991+A1: 1992+A2: 1993+A3: 1995+A4: 1996 European Committee for Electrotechnical Standardization(CENELEC) EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical Business Equipment. d)The standard for safety is required at the system sides elsewhere. 7-2. EMC a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI), 1992 b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment.’’ International Special Committee on Radio Interference. c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment.’’ European Committee for Electrotechnical Standardization.(CENELEC), 1998 Ver. 0.1 Jan. 17, 2003 23 / 26 LC201V02 Liquid Crystal Display Product Specification 8. Packing 8-1. Designation of Lot Mark a) Lot Mark A B C D E F G H I J K L M A,B,C : SIZE D : YEAR E : MONTH F,G : PANEL CODE H : ASSEMBLY CODE I,J,K,L,M : SERIAL NO. Note 1. YEAR Year 97 98 99 2000 2001 2002 2003 2004 2005 2006 2007 Mark 7 8 9 0 1 2 3 4 5 6 7 Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Mark 1 2 4 4 5 6 7 8 9 A B C 2. MONTH 3. Serial No. Year 1 ~ 99999 Mark 00001 ~ 99999 100000 ~ A0001 ~ A9999, ..... , Z9999 b) Location of Lot Mark Serial NO. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice. 8-2. Packing Form a) Package quantity in one box : 3 pcs b) Box Size : 470mm × 253mm × 573mm Ver. 0.1 Jan. 17, 2003 24 / 26 LC201V02 Liquid Crystal Display Product Specification 9. PRECAUTIONS Please pay attention to the followings when you use this TFT LCD module. 9-1. MOUNTING PRECAUTIONS (1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer. Transparent protective plate should have sufficient strength in order to the resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental to the polarizer.) (7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (9) Do not open the case because inside circuits do not have sufficient strength. 9-2. OPERATING PRECAUTIONS (1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage : V=±200mV(Over and under shoot voltage) (2) Response time depends on the temperature.(In lower temperature, it becomes longer.) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference. (7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can not be operated its full characteristics perfectly. (8) A screw which is fastened up the steels should be a machine screw (if not, it causes metal foreign material and deal LCM a fatal blow) (9) Please do not set LCD on its edge. Ver. 0.1 Jan. 17, 2003 25 / 26 LC201V02 Liquid Crystal Display Product Specification 9-3. ELECTROSTATIC DISCHARGE CONTROL Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly. 9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE Strong light exposure causes degradation of polarizer and color filter. 9-5. STORAGE When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5°C and 35°C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped. 9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM (1) The protection film is attached to the bezel with a small masking tape. When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the protection film is peeled off. (3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. Ver. 0.1 Jan. 17, 2003 26 / 26