LED Highly-Diffused Lights (75 mm) Features • Designed to minimize surface textures and elevation changes, while providing uniform illumination over the field of view • 59 mm x 75 mm light aperture • The suggested field of view is 38 mm in diameter and the suggested stand off is 25 mm • Black anodized aluminum housing LED Highly-Diffused Light Models Illumination Type Models LEDRS75N† Color Red 640 nm Continuous highly-diffused light LEDGS75N† LEDRS75N-S† † Green 530 nm Strobed highly-diffused light Red 640 nm Cable Supply Voltage Supply Current 0.5 m (18") terminated with 9-pin D-sub connector (male pins) 12V dc ±10% with voltage regulation of ±1% 1.8 m (6') terminated with 9-pin D-sub connector (male pins) 24V dc ±10% with voltage regulation of ±1% Connections 980 mA max. Pin 1 = +V fan Pin 2 = dc common fan Pin 3 = dc common Pin 4 = +V 1.0 A max. Power supply model PSA-12(E) or PS2V-12(E) is recommended (see other side) 7.0 A max. 1 ms pulse Pin 4 or 5 = +V Pin 1 or 6 = dc common Use strobe control module model SCM (see other side) These models are not stocked and are non-returnable. Useful Life Green model: 50,000 hours; Red models: 60,000 hours. Note: actual useful life of strobed lights depends on duty cycle Environmental Rating IEC IP20; NEMA 1 Operating Conditions Temperature: 0° to 40°C (+32° to 104°F) Maximum relative humidity: 95% at 40°C (non-condensing) 82.6 mm 75 mm (3.25") (2.95") Light Aperture 75 mm (2.95") Light Aperture 25.4 mm (1.00") 25.4 mm (1.00") 138.4 mm (5.45") 12.7 mm (0.50") See Table 25.8 mm (1.02") 12.7 mm (0.50") 25.4 mm (1.00") 77.0 mm (3.03) M6 x 1.0 6.4 (0.25") DEEP (4x) WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. Printed in USA 05/01 P/N 67442 LED Highly-Diffused Lights (75 mm) Accessories Continuous Power Supplies Models Input Cord Input North America (NEMA 5-15) PSA-12 100-250V ac 50/60 Hz Cont. Europe (Schuko CEE 7) PSA-12E PSC-24† PSC-24E† North America (NEMA 5-15) 100-250V ac 50/60 Hz Cont. Europe (Schuko CEE 7) Output Cable Output 12V dc ±5% with voltage regulation of ±1% 3.5 A max. 1.8 m (6') Terminated with 9-pin D-sub connector (female pins) 24V dc ±5% with voltage regulation of ±1% 2.2 A max. 1.8 m (6') 2-wire Unterminated Used with Continuous types: LEDRS75N LEDGS75N SCM Strobe Control Module (see below) Variable Power Supplies (see data sheet p/n 67449) Models Input Cord Input PS2V-12† 100-140V ac 60 Hz North America (NEMA 5-15) PS2V-12E† 200-250V ac 50 Hz Cont. Europe (Schuko CEE 7) Output Cable Output 2-channels 6 - 12V dc 2 A max. per channel 1.8 m (6') Terminated with 9-pin D-sub connector (female pins) Used with Continuous types: LEDRS75N LEDGS75N Strobe Control Module (see data sheet p/n 67448) Models SCM† Input Trigger Input 24V dc ±5% 2 A max. 5 - 12V dc pulse rising or falling (switch selectable) 10 mA max. (Use Power Supply PSC-24 or PSC-24E) Output 2-channels 24V dc ±5% 9 A nominal per channel @ 60 Hz Output Pulse Range 5 to 1,300 microseconds Used with Strobed types: LEDRS75N-S Extension Cables Models DB906 Length Configuration DB910 Terminated both ends with 9-pin D-sub connector, for continuous lights 3.0 m (10') (one end male pins and opposite end female pins) DB9Y† 1.8 m (6') DB906S† 1.8 m (6') † DB910S DB9YS 1.8 m (6') † Continuous types: LEDRS75N LEDGS75N Y cable for powering 2 lights from one supply, for continuous lights Terminated both ends with 9-pin D-sub connector, for strobed lights 3.0 m (10') (one end male pins and opposite end female pins) † † Used with 1.8 m (6') † Strobed types: LEDRS75N-S Y cable for powering 2 lights from one supply, for strobed lights These models are not stocked and are non-returnable. Banner Engineering Corp., 9714 Tenth Ave. No., Mpls., MN 55441 • Ph: 763.544.3164 • www.bannerengineering.com • Email: [email protected]