Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag (Slo-Blo®) > 215SP Series 215SP Series, PS E 5x20 mm, Time-Lag Fuse (Slo-Blo®) Description 5x20mm Time-Lag surge withstanding ceramic body cartridge fuse designed to IEC specification Features t %FTJHOFEUP International (IEC) Standards for use globally specification for Time-Lag Fuses t 3P)4DPNQMJBOUBOE Pb-free t .FFUTUIF*&$ 60127-2, Sheet 5 Applications Agency PS E Agency File Number Ampere Range Leaded NBK080205E10480B NBK250702E10480F 1A – 5A 6.3A – 10A Certificate No. CQC10012041490 1A – 6.3A Certificate No. SU05001-2011B SU05001-10001 SU05001-10002 Certificate No. Used as supplementary protection in appliance or utilization equipment to provide individual protection for components or internal circuits. Electrical Characteristics for Series % of Ampere Rating 210% 1A – 2.5A 3.15A – 6.3A 8A 275% Recognised File No. Guide No. E10480 JDYX2 File No. Acc. Class No. 029862 LR1422-30 1A – 10A Licence. No. 40013521 1 – 8A 1A – 10A 400% 1000% 1A – 10A Ampere Rating Opening Time 1A - 3.15A 30 minutes, Maximum 4A - 6.3A 30 minutes, Maximum 8A - 10A 30 minutes, Maximum 1A - 3.15A .75 sec. Min.; 80 secs. Max. 4A - 6.3A .75 sec. Min.; 80 secs. Max. 8A - 10A .75 sec. Min.; 80 secs. Max. 1A - 3.15A .095 sec. Min.; 5 secs. Max. 4A - 6.3A .150 sec. Min.; 5 secs. Max. 8A - 10A .150 sec. Min.; 5 secs. Max. 1A - 3.15A .010 sec. Min.; .150 secs. Max. 4A - 6.3A .010 sec. Min.; .150 secs. Max. 8A - 10A .010 sec. Min.; .150 secs. Max. Electrical Characteristic Specifications by Item Amp Code Amp Voltage Interrupting Rating Rating Rating Nominal Resistance Cold Ohms (Ohms) Nominal Melting I2t (A2 sec) Maximum Voltage Drop at Rated Current (mV) Maximum Power Dissipation at 1.5In Rated Current (W) Agency Approvals PS E 001 1 250 0.1515 1.52000 350 2.5 x x x x x x 1.25 1.25 250 0.1074 3.20000 300 2.5 x x x x x x x 01.6 1.6 250 0.0707 6.83000 200 2.5 x x x x x x x 002 2 250 0.0566 11.68000 190 2.5 x x x x x x x 02.5 2.5 250 0.0386 22.29000 180 2.5 x x x x x x x 3.15 3.15 250 0.0283 43.25500 140 4 x x x x x x x 004 4 250 0.0185 46.96000 100 4 x x x x x x x 005 5 250 0.0153 66.09500 100 4 x x x x x x x 06.3 6.3 250 0.0108 128.75000 100 4 x x x x x x x 008 8 250 0.0092 209.88000 100 4 x x x x x 010 10 250 0.0066 333.56500 100 4 x x x 1500 A @ 250 VAC x x x I2t test at 10x rated current © 2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/series/215SP.html for current information. 215SP Series Revised: June 3, 2012 215SP Series Agency Approvals Introduction to & Circuit Protection Axial Lead Cartridge Fuses 5×20 mm > Time-Lag (Slo-Blo®) >Transientology 215SP Series Average Time Current Curves 215001. 2151.25 21501.6 215002. 21502.5 2153.15 215004. 215005. 21506.3. 215008. 215010. Temperature Rerating Curve 10000 Time (seconds) 1000 100 10 1 0.1 0.01 0.001 0.01 0.1 1 10 100 Amps Soldering Parameters - Wave Soldering Recommended Process Parameters: 280 260 Wave Parameter 240 220 Lead-Free Recommendation Preheat: 200 (Depends on Flux Activation Temperature) 180 160 140 120 100 80 60 40 (Typical Industry Recommendation) Temperature Minimum: 100° C Temperature Maximum: Preheat Time: 150° C 60-180 seconds Solder Pot Temperature: 260° C Maximum Solder Dwell Time: 2-5 seconds Time (Seconds) Cooling Time Preheat Time Dwell Time 240 230 220 210 200 190 180 170 160 150 140 130 120 110 90 100 80 70 60 50 40 30 0 0 20 20 10 Temperature (°C) - Measured on bottom side of board 300 Recommended Hand-Solder Parameters: Solder Iron Temperature: 350° C +/- 5°C )FBUJOH5JNFTFDPOETNBY Note: These devices are not recommended for IR or Convection Reflow process. Different values of A and B available, please contact the Littelfuse sales representative in your region: B A C For the pigtailed fuse, please follow the recommendations below for axial lead forming and mounting into PCB: Lead forming: A C The distance C between cap flat surface and axial lead shall be greater than 1.0 mm. PCB mounting: B 215SP Series According to the standard of IPC-A-610, the distance between PCB and fuse cap is recommended to be a minimum of 1.5 mm. © 2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/series/215SP.html for current information. Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag (Slo-Blo®) > 215SP Series Product Characteristics Materials Body: Ceramic Cap: Nickel–plated Brass Leads: Tin–plated Copper Operating Temperature –55ºC to +125ºC Terminal Strength MIL-STD-202G, Method 211A, Test Condition A Thermal Shock MIL-STD-202G, Method 107G, Test Condition B (5 cycles, –65ºC to +125ºC) Solderability Reference IEC 60127 Second Edition 2003-01 Annex A Vibration MIL-STD-202G, Method 201A Product Marking Cap 1: Brand logo, current and voltage ratings Cap 2: Agency approval marks Humidity MIL-STD-202G, Method 103B, Test $POEJUJPO")JHI3) BOE elevated temp (40ºC) for 240 hours) Salt Spray MIL-STD-202G, Method 101D, Test Condition B Dimensions Part Numbering System 0215 xxxx M X E SP P 20 ± 0.5 Series Current Rating Code 5.1 ± 0.6 Refer to Amp Code column of Electrical Characteristics Table 5.1 ± 0.6 * 8A and 10A have 0.8mm diameter Quantity Code All unit in mm. M = 1000 Packaging Code X = Filler Option Codes Single-Cap Pigtail Lead-Free Packaging Packaging Option 215SP Series Bulk Packaging Specification Quantity Packaging Code Reel Size N/A 1000 MXE N/A © 2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/series/215SP.html for current information. 215SP Series 215SP Series Blank : Cartidge Type Fuse E : Axial Leaded Fuse