LM2586 SIMPLE SWITCHER ® 3A Flyback Regulator with Shutdown General Description Features The LM2586 series of regulators are monolithic integrated circuits specifically designed for flyback, step-up (boost), and forward converter applications. The device is available in 4 different output voltage versions: 3.3V, 5.0V, 12V, and adjustable. Requiring a minimum number of external components, these regulators are cost effective, and simple to use. Included in the datasheet are typical circuits of boost and flyback regulators. Also listed are selector guides for diodes and capacitors and a family of standard inductors and flyback transformers designed to work with these switching regulators. The power switch is a 3.0A NPN device that can stand-off 65V. Protecting the power switch are current and thermal limiting circuits, and an undervoltage lockout circuit. This IC contains an adjustable frequency oscillator that can be programmed up to 200 kHz. The oscillator can also be synchronized with other devices, so that multiple devices can operate at the same switching frequency. Other features include soft start mode to reduce in-rush current during start up, and current mode control for improved rejection of input voltage and output load transients and cycle-by-cycle current limiting. The device also has a shutdown pin, so that it can be turned off externally. An output voltage tolerance of ± 4%, within specified input voltages and output load conditions, is guaranteed for the power supply system. Requires few external components Family of standard inductors and transformers NPN output switches 3.0A, can stand off 65V Wide input voltage range: 4V to 40V Adjustable switching frequency: 100 kHz to 200 kHz External shutdown capability Draws less than 60 µA when shut down Frequency synchronization Current-mode operation for improved transient response, line regulation, and current limit n Internal soft-start function reduces in-rush current during start-up n Output transistor protected by current limit, under voltage lockout, and thermal shutdown n System output voltage tolerance of ± 4% max over line and load conditions n n n n n n n n n Typical Applications n n n n Flyback regulator Forward converter Multiple-output regulator Simple boost regulator Connection Diagrams Bent, Staggered Leads 7-Lead TO-220 (T) Top View Bent, Staggered Leads 7-Lead TO-220 (T) Side View 01251618 01251617 Order Number LM2586T3.3, LM2586T-5.0, LM2586T-12 or LM2586T-ADJ See NS Package Number TA07B SIMPLE SWITCHER ® and Switchers Made Simple ® © 2005 National Semiconductor Corporation are registered trademarks of National Semiconductor Corporation. DS012516 www.national.com LM2586 SIMPLE SWITCHER 3A Flyback Regulator with Shutdown July 2005 LM2586 Connection Diagrams (Continued) 7-Lead TO-263 (S) Top View 7-Lead TO-263 (S) Side View 01251620 01251619 Order number LM2586S-3.3, LM2586S-5.0, LM2586S-12 or LM2586S-ADJ Tape and Reel Order Number LM2586SX-3.3, LM2586SX-5.0, LM2586SX-12 or LM2586SX-ADJ See NS Package Number TS7B Package Type Ordering Information NSC Package Order Number Drawing 7-Lead TO-220 Bent, Staggered Leads TA07B 7-Lead TO-263 TS7B LM2586S-3.3, LM2586S-5.0, LM2586S-12, LM2586S-ADJ 7-Lead TO-263 Tape and Reel TS7B LM2586SX-3.3, LM2586SX-5.0, LM2586SX-12, LM2586SX-ADJ www.national.com LM2586T-3.3, LM2586T-5.0, LM2586T-12, LM2586T-ADJ 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. −0.4V ≤ VIN ≤ 45V Input Voltage Internally Limited Compensation Pin Voltage −0.4V ≤ VCOMP ≤ 2.4V Feedback Pin Voltage −0.4V ≤ VFB ≤ 2 VOUT ON /OFF Pin Voltage −0.4V ≤ VSH ≤ 6V Sync Pin Voltage Internally Limited Storage Temperature Range −65˚C to +150˚C Maximum Junction Temperature (Note 3) 150˚C 2 kV Operating Ratings 4V ≤ VIN ≤ 40V Supply Voltage Output Switch Voltage −0.4V ≤ VSYNC ≤ 2V Power Dissipation (Note 3) 260˚C Minimum ESD Rating (C = 100 pF, R = 1.5 kΩ) −0.4V ≤ VSW ≤ 65V Switch Voltage Switch Current (Note 2) Lead Temperature (Soldering, 10 sec.) 0V ≤ VSW ≤ 60V Output Switch Current ISW ≤ 3.0A Junction Temp. Range −40˚C ≤ TJ ≤ +125˚C Electrical Characteristics Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature Range. Unless otherwise specified, VIN = 5V. LM2586-3.3 Symbol Parameters Conditions Typical Min Max Units 3.3 3.17/3.14 3.43/3.46 V 20 50/100 mV 20 50/100 mV SYSTEM PARAMETERS Test Circuit of Figure 1 (Note 4) VOUT Output Voltage VIN = 4V to 12V ∆VOUT/ Line Regulation VIN = 4V to 12V ILOAD = 0.3 to 1.2A ∆VIN ∆VOUT/ ILOAD = 0.3A Load Regulation ∆ILOAD η VIN = 12V ILOAD = 0.3A to 1.2A Efficiency VIN = 5V, ILOAD = 0.3A 76 % UNIQUE DEVICE PARAMETERS (Note 5) VREF ∆VREF Output Reference Measured at Feedback Pin Voltage VCOMP = 1.0V Reference Voltage VIN = 4V to 40V 3.3 3.242/3.234 3.358/3.366 2.0 V mV Line Regulation GM AVOL Error Amp ICOMP = −30 µA to +30 µA Transconductance VCOMP = 1.0V Error Amp VCOMP = 0.5V to 1.6V Voltage Gain RCOMP = 1.0 MΩ (Note 6) 1.193 0.678 2.259 mmho 260 151/75 Typical Min Max Units 5.0 4.80/4.75 5.20/5.25 V 20 50/100 mV 20 50/100 mV V/V LM2586-5.0 Symbol Parameters Conditions SYSTEM PARAMETERS Test Circuit of Figure 1 (Note 4) VOUT Output Voltage VIN = 4V to 12V ILOAD = 0.3A to 1.1A ∆VOUT/ Line Regulation ∆VIN ∆VOUT/ ILOAD = 0.3A Load Regulation ∆ILOAD η VIN = 4V to 12V VIN = 12V ILOAD = 0.3A to 1.1A Efficiency VIN = 12V, ILOAD = 0.6A 80 % UNIQUE DEVICE PARAMETERS (Note 5) VREF Output Reference Voltage Measured at Feedback Pin VCOMP = 1.0V 3 5.0 4.913/4.900 5.088/5.100 V www.national.com LM2586 Absolute Maximum Ratings (Note 1) LM2586 Electrical Characteristics LM2586-5.0 Symbol (Continued) Parameters ∆VREF (Continued) Reference Voltage Conditions Typical VIN = 4V to 40V Min Max 3.3 Units mV Line Regulation GM AVOL Error Amp ICOMP = −30 µA to +30 µA Transconductance VCOMP = 1.0V Error Amp VCOMP = 0.5V to 1.6V Voltage Gain RCOMP = 1.0 MΩ (Note 6) 0.750 0.447 1.491 mmho 165 99/49 Typical Min Max Units 12.0 11.52/11.40 12.48/12.60 V 20 100/200 mV 20 100/200 mV V/V LM2586-12 Symbol Parameters Conditions SYSTEM PARAMETERS Test Circuit of Figure 2 (Note 4) VOUT Output Voltage VIN = 4V to 10V ILOAD = 0.2A to 0.8A ∆VOUT/ Line Regulation ∆VIN ∆VOUT/ ILOAD = 0.2A Load Regulation VIN = 10V Efficiency VIN = 10V, ILOAD = 0.6A ∆ILOAD η VIN = 4V to 10V ILOAD = 0.2A to 0.8A 93 % UNIQUE DEVICE PARAMETERS (Note 5) VREF Output Reference Voltage VCOMP = 1.0V ∆VREF Reference Voltage VIN = 4V to 40V Measured at Feedback Pin 12.0 11.79/11.76 12.21/12.24 7.8 V mV Line Regulation GM AVOL Error Amp ICOMP = −30 µA to +30 µA Transconductance VCOMP = 1.0V Error Amp VCOMP = 0.5V to 1.6V Voltage Gain RCOMP = 1.0 MΩ (Note 6) 0.328 0.186 70 41/21 0.621 mmho V/V LM2586-ADJ Symbol Parameters Conditions Typical Min Max Units 12.0 11.52/11.40 12.48/12.60 V 20 100/200 mV 20 100/200 mV SYSTEM PARAMETERS Test Circuit of Figure 2 (Note 4) VOUT Output Voltage VIN = 4V to 10V ILOAD = 0.2A to 0.8A ∆VOUT/ Line Regulation ∆VIN ∆VOUT/ ILOAD = 0.2A Load Regulation ∆ILOAD η VIN = 4V to 10V VIN = 10V ILOAD = 0.2A to 0.8A Efficiency VIN = 10V, ILOAD = 0.6A 93 % UNIQUE DEVICE PARAMETERS (Note 5) VREF ∆VREF Output Reference Measured at Feedback Pin Voltage VCOMP = 1.0V Reference Voltage VIN = 4V to 40V 1.230 1.208/1.205 1.252/1.255 1.5 V mV Line Regulation GM AVOL Error Amp ICOMP = −30 µA to +30 µA Transconductance VCOMP = 1.0V Error Amp Voltage Gain VCOMP = 0.5V to 1.6V, RCOMP = 1.0 MΩ (Note 6) www.national.com 4 3.200 1.800 670 400/200 6.000 mmho V/V LM2586-ADJ Symbol IB LM2586 Electrical Characteristics (Continued) (Continued) Parameters Error Amp Conditions Typical Max Units 125 425/600 nA Switch Off (Note 8) 11 15.5/16.5 mA ISWITCH = 1.8A 50 100/115 mA VSH = 3V 16 100/300 µA VCOMP = 1.0V Min Input Bias Current COMMON DEVICE PARAMETERS for all versions (Note 5) IS Input Supply Current IS/D Shutdown Input Supply Current VUV Input Supply RLOAD = 100Ω 3.30 3.05 3.75 V 100 85/75 115/125 kHz Undervoltage Lockout fO Oscillator Frequency Measured at Switch Pin RLOAD = 100Ω, VCOMP = 1.0V Freq. Adj. Pin Open (Pin 1) RSET = 22 kΩ fSC Short-Circuit Measured at Switch Pin Frequency RLOAD = 100Ω 200 kHz 25 kHz VFEEDBACK = 1.15V VEAO Error Amplifier Upper Limit Output Swing (Note 7) 2.8 Lower Limit 2.6/2.4 0.25 V 0.40/0.55 V (Note 8) IEAO Error Amp (Note 9) Output Current 165 110/70 260/320 µA 11.0 8.0/7.0 17.0/19.0 µA 98 93/90 (Source or Sink) ISS Soft Start Current VFEEDBACK = 0.92V DMAX Maximum Duty Cycle RLOAD = 100Ω VCOMP = 1.0V % (Note 7) IL Switch Leakage Switch Off 15 Current VSWITCH = 60V VSUS Switch Sustaining Voltage dV/dT = 1.5V/ns VSAT Switch Saturation Voltage ISWITCH = 3.0A 0.45 ICL NPN Switch Current Limit 4.0 VSTH Synchronization FSYNC = 200 kHz 0.75 Threshold Voltage VCOMP = 1V, VIN = 5V Synchronization VIN = 5V Pin Current VCOMP = 1V, VSYNC = VSTH ISYNC VSHTH ISH ON/OFF Pin (Pin 1) VCOMP = 1V Threshold Voltage (Note 10) ON/OFF Pin (Pin 1) VCOMP = 1V Current VSH = VSHTH 300/600 µA 65 V 3.0 7.0 A 0.625/0.40 0.875/1.00 V 200 µA 100 5 V 0.65/0.9 1.6 1.0/0.8 2.2/2.4 V 40 15/10 65/75 µA www.national.com LM2586 Electrical Characteristics LM2586-ADJ Symbol (Continued) (Continued) Parameters Conditions Typical Min Max Units COMMON DEVICE PARAMETERS for all versions (Note 5) θJA Thermal Resistance T Package, Junction to Ambient (Note 11) 65 θJA T Package, Junction to Ambient (Note 12) 45 θJC T Package, Junction to Case 2 θJA S Package, Junction to Ambient (Note 13) 56 θJA S Package, Junction to Ambient (Note 14) 35 θJA S Package, Junction to Ambient (Note 15) 26 θJC S Package, Junction to Case 2 ˚C/W Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. These ratings apply when the current is limited to less than 1.2 mA for pins 1, 2, 3, and 6. Operating ratings indicate conditions for which the device is intended to be functional, but device parameter specifications may not be guaranteed under these conditions. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: Note that switch current and output current are not identical in a step-up regulator. Output current cannot be internally limited when the LM2586 is used as a step-up regulator. To prevent damage to the switch, the output current must be externally limited to 3A. However, output current is internally limited when the LM2586 is used as a flyback regulator (see the Application Hints section for more information). Note 3: The junction temperature of the device (TJ) is a function of the ambient temperature (TA), the junction-to-ambient thermal resistance (θJA), and the power dissipation of the device (PD). A thermal shutdown will occur if the temperature exceeds the maximum junction temperature of the device: PD x θJA + TA(MAX) ≥ TJ(MAX). For a safe thermal design, check that the maximum power dissipated by the device is less than: PD ≤ [TJ(MAX) − TA(MAX)]/θJA. When calculating the maximum allowable power dissipation, derate the maximum junction temperature — this ensures a margin of safety in the thermal design. Note 4: External components such as the diode, inductor, input and output capacitors can affect switching regulator performance. When the LM2586 is used as shown in Figures 1, 2, system performance will be as specified by the system parameters. Note 5: All room temperature limits are 100% production tested, and all limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. Note 6: A 1.0 MΩ resistor is connected to the compensation pin (which is the error amplifier output) to ensure accuracy in measuring AVOL. Note 7: To measure this parameter, the feedback voltage is set to a low value, depending on the output version of the device, to force the error amplifier output high and the switch on. Note 8: To measure this parameter, the feedback voltage is set to a high value, depending on the output version of the device, to force the error amplifier output low and the switch off. Note 9: To measure the worst-case error amplifier output current, the LM2586 is tested with the feedback voltage set to its low value (Note 7) and at its high value (Note 8). Note 10: When testing the minimum value, do not sink current from this pin — isolate it with a diode. If current is drawn from this pin, the frequency adjust circuit will begin operation (see Figure 41). Note 11: Junction to ambient thermal resistance (no external heat sink) for the 7 lead TO-220 package mounted vertically, with 1⁄2 inch leads in a socket, or on a PC board with minimum copper area. Note 12: Junction to ambient thermal resistance (no external heat sink) for the 7 lead TO-220 package mounted vertically, with 1⁄2 inch leads soldered to a PC board containing approximately 4 square inches of (1 oz.) copper area surrounding the leads. Note 13: Junction to ambient thermal resistance for the 7 lead TO-263 mounted horizontally against a PC board area of 0.136 square inches (the same size as the TO-263 package) of 1 oz. (0.0014 in. thick) copper. Note 14: Junction to ambient thermal resistance for the 7 lead TO-263 mounted horizontally against a PC board area of 0.4896 square inches (3.6 times the area of the TO-263 package) of 1 oz. (0.0014 in. thick) copper. Note 15: Junction to ambient thermal resistance for the 7 lead TO-263 mounted horizontally against a PC board copper area of 1.0064 square inches (7.4 times the area of the TO-263 package) of 1 oz. (0.0014 in. thick) copper. Additional copper area will reduce thermal resistance further. See the thermal model in Switchers Made Simple ® software. www.national.com 6 LM2586 Typical Performance Characteristics Supply Current vs Temperature Reference Voltage vs Temperature 01251602 01251603 ∆Reference Voltage vs Supply Voltage Supply Current vs Switch Current 01251605 01251604 Current Limit vs Temperature Feedback Pin Bias Current vs Temperature 01251606 01251607 7 www.national.com LM2586 Typical Performance Characteristics (Continued) Switch Saturation Voltage vs Temperature Switch Transconductance vs Temperature 01251608 01251609 Oscillator Frequency vs Temperature Error Amp Transconductance vs Temperature 01251610 01251611 Error Amp Voltage Gain vs Temperature Short Circuit Frequency vs Temperature 01251613 01251612 www.national.com 8 LM2586 Typical Performance Characteristics (Continued) Shutdown Supply Current vs Temperature ON/OFF Pin Current vs Voltage 01251614 01251615 Oscillator Frequency vs Resistance 01251616 Flyback Regulator 01251601 9 www.national.com LM2586 Test Circuits 01251621 CIN1 — 100 µF, 25V Aluminum Electrolytic CIN2 — 0.1 µF Ceramic T — 22 µH, 1:1 Schott #67141450 D — 1N5820 COUT — 680 µF, 16V Aluminum Electrolytic CC — 0.47 µF Ceramic RC — 2k FIGURE 1. LM2586-3.3 and LM2586-5.0 01251622 CIN1 — 100 µF, 25V Aluminum Electrolytic CIN2 — 0.1 µF Ceramic L — 15 µH, Renco #RL-5472-5 D — 1N5820 COUT — 680 µF, 16V Aluminum Electrolytic CC — 0.47 µF Ceramic RC — 2k For 12V Devices: R1 = Short (0Ω) and 2 = Open For ADJ Devices: R1 = 48.75k, ± 0.1% and 2 = 5.62k, ± 0.1% FIGURE 2. LM2586-12 and LM2586-ADJ www.national.com 10 LM2586 Block Diagram 01251623 For Fixed Versions 3.3V, R1 = 3.4k, R2 = 2k 5.0V, R1 = 6.15k, R2 = 2k 12V, R1 = 8.73k, R2 = 1k For Adj. Version R1 = Short (0Ω), R2 = Open FIGURE 3. Block Diagram lapses, reversing the voltage polarity of the primary and secondary windings. Now rectifier D1 is forward biased and current flows through it, releasing the energy stored in the transformer. This produces voltage at the output. The output voltage is controlled by modulating the peak switch current. This is done by feeding back a portion of the output voltage to the error amp, which amplifies the difference between the feedback voltage and a 1.230V reference. The error amp output voltage is compared to a ramp voltage proportional to the switch current (i.e., inductor current during the switch on time). The comparator terminates the switch on time when the two voltages are equal, thereby controlling the peak switch current to maintain a constant output voltage. Flyback Regulator Operation The LM2586 is ideally suited for use in the flyback regulator topology. The flyback regulator can produce a single output voltage, such as the one shown in Figure 4, or multiple output voltages. In Figure 4, the flyback regulator generates an output voltage that is inside the range of the input voltage. This feature is unique to flyback regulators and cannot be duplicated with buck or boost regulators. The operation of a flyback regulator is as follows (refer to Figure 4): when the switch is on, current flows through the primary winding of the transformer, T1, storing energy in the magnetic field of the transformer. Note that the primary and secondary windings are out of phase, so no current flows through the secondary when current flows through the primary. When the switch turns off, the magnetic field col- 11 www.national.com LM2586 Flyback Regulator Operation (Continued) 01251624 As shown in Figure 4, the LM2586 can be used as a flyback regulator by using a minimum number of external components. The switching waveforms of this regulator are shown in Figure 5. Typical Performance Characteristics observed during the operation of this circuit are shown in Figure 6. FIGURE 4. 12V Flyback Regulator Design Example Typical Performance Characteristics 01251665 A: Switch Voltage, 20V/div B: Switch Current, 2A/div C: Output Rectifier Current, 2A/div D: Output Ripple Voltage, 50 mV/div AC-Coupled FIGURE 5. Switching Waveforms www.national.com 12 LM2586 Typical Performance Characteristics (Continued) 01251666 FIGURE 6. VOUT Response to Load Current Step Typical Flyback Regulator Applications Figure 7 through Figure 12 show six typical flyback applications, varying from single output to triple output. Each drawing contains the part number(s) and manufacturer(s) for every component except the transformer. For the transformer part numbers and manufacturers’ names, see the table in Figure 13. For applications with different output voltages — requiring the LM2586-ADJ — or different output configurations that do not match the standard configurations, refer to the Switchers Made Simple software. 01251627 FIGURE 7. Single-Output Flyback Regulator 13 www.national.com LM2586 Typical Flyback Regulator Applications (Continued) 01251628 FIGURE 8. Single-Output Flyback Regulator 01251629 FIGURE 9. Single-Output Flyback Regulator www.national.com 14 LM2586 Typical Flyback Regulator Applications (Continued) 01251630 FIGURE 10. Dual-Output Flyback Regulator 01251631 FIGURE 11. Dual-Output Flyback Regulator 15 www.national.com LM2586 Typical Flyback Regulator Applications (Continued) 01251632 FIGURE 12. Triple-Output Flyback Regulator TRANSFORMER SELECTION (T) Figure 13 lists the standard transformers available for flyback regulator applications. Included in the table are the turns ratio(s) for each transformer, as well as the output voltages, input voltage ranges, and the maximum load currents for each circuit. Applications Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Transformers T7 T7 T7 T6 T6 T5 18V–36V VIN 4V–6V 4V–6V 8V–16V 4V–6V 18V–36V VOUT1 3.3V 5V 12V 12V 12V 5V IOUT1 (Max) 1.4A 1A 0.8A 0.15A 0.6A 1.8A 1 1 1 N1 1.2 1.2 0.5 VOUT2 −12V −12V 12V IOUT2(Max) 0.15A 0.6A 0.25A 1.2 1.2 N2 1.15 VOUT3 −12V IOUT3 (Max) 0.25A N3 1.15 FIGURE 13. Transformer Selection Table www.national.com 16 Transformer Type LM2586 Typical Flyback Regulator Applications (Continued) Manufacturers’ Part Numbers Coilcraft (Note 16) Surface Mount Coilcraft (Note 16) Pulse (Note 17) Surface Mount Pulse (Note 17) Renco (Note 18) Schott (Note 19) T5 Q4338-B Q4437-B PE-68413 — RL-5532 67140890 T6 Q4339-B Q4438-B PE-68414 — RL-5533 67140900 T7 S6000-A S6057-A — PE-68482 RL-5751 26606 Note 16: Coilcraft Inc., Phone: (800) 322-2645 1102 Silver Lake Road, Cary, IL 60013 Fax: (708) 639-1469 European Headquarters, 21 Napier Place Phone: +44 1236 730 595 Wardpark North, Cumbernauld, Scotland G68 0LL Note 17: Pulse Engineering Inc., 12220 World Trade Drive, San Diego, CA 92128 European Headquarters, Dunmore Road Tuam, Co. Galway, Ireland Fax: (619) 674-8262 Phone: +353 93 24 107 Fax: +353 93 24 459 Note 18: Renco Electronics Inc., Phone: (800) 645-5828 60 Jeffryn Blvd. East, Deer Park, NY 11729 Note 19: Schott Corp., Fax: +44 1236 730 627 Phone: (619) 674-8100 Fax: (516) 586-5562 Phone: (612) 475-1173 1000 Parkers Lane Road, Wayzata, MN 55391 Fax: (612) 475-1786 FIGURE 14. Transformer Manufacturer Guide TRANSFORMER FOOTPRINTS Figure 15 through Figure 29 show the footprints of each transformer, listed in Figure 14. T5 T7 01251633 Top View 01251635 FIGURE 15. Coilcraft S6000-A FIGURE 17. Coilcraft Q4437-B (Surface Mount) T6 T5 01251634 Top View FIGURE 16. Coilcraft Q4339-B 01251636 Top View FIGURE 18. Coilcraft Q4338-B 17 www.national.com LM2586 Typical Flyback Regulator Applications (Continued) T5 T7 01251642 01251637 Top View Top View FIGURE 23. Pulse PE-68413 (Surface Mount) FIGURE 19. Coilcraft S6057-A (Surface Mount) T7 T6 01251643 Top View 01251638 Top View FIGURE 24. Renco RL-5751 FIGURE 20. Coilcraft Q4438-B (Surface Mount) T6 T7 01251645 Top View 01251639 Top View FIGURE 25. Renco RL-5533 FIGURE 21. Pulse PE-68482 T5 T6 01251646 Top View 01251640 Top View FIGURE 26. Renco RL-5532 FIGURE 22. Pulse PE-68414 (Surface Mount) www.national.com 18 LM2586 Typical Flyback Regulator Applications (Continued) T7 01251647 Top View FIGURE 27. Schott 26606 Step-Up (Boost) Regulator Operation T6 Figure 30 shows the LM2586 used as a step-up (boost) regulator. This is a switching regulator that produces an output voltage greater than the input supply voltage. A brief explanation of how the LM2586 Boost Regulator works is as follows (refer to Figure 30). When the NPN switch turns on, the inductor current ramps up at the rate of VIN/L, storing energy in the inductor. When the switch turns off, the lower end of the inductor flies above VIN, discharging its current through diode (D) into the output capacitor (COUT) at a rate of (VOUT − VIN)/L. Thus, energy stored in the inductor during the switch on time is transferred to the output during the switch off time. The output voltage is controlled by adjusting the peak switch current, as described in the flyback regulator section. 01251649 Top View FIGURE 28. Schott 67140900 T5 01251650 Top View FIGURE 29. Schott 67140890 19 www.national.com LM2586 Step-Up (Boost) Regulator Operation (Continued) 01251651 FIGURE 30. 12V Boost Regulator By adding a small number of external components (as shown in Figure 30), the LM2586 can be used to produce a regulated output voltage that is greater than the applied input www.national.com voltage. The switching waveforms observed during the operation of this circuit are shown in Figure 31. Typical performance of this regulator is shown in Figure 32. 20 LM2586 Typical Performance Characteristics 01251667 A: Switch Voltage,10V/div B: Switch Current, 2A/div C: Inductor Current, 2A/div D: Output Ripple Voltage,100 mV/div, AC-Coupled FIGURE 31. Switching Waveforms 01251668 FIGURE 32. VOUT Response to Load Current Step ber(s) and manufacturer(s) for every component. For the fixed 12V output application, the part numbers and manufacturers’ names for the inductor are listed in a table in Figure 34. For applications with different output voltages, refer to the Switchers Made Simple software. Typical Boost Regulator Applications Figures 33, 35 through Figure 37 show four typical boost applications — one fixed and three using the adjustable version of the LM2586. Each drawing contains the part num- 21 www.national.com LM2586 Typical Boost Regulator Applications (Continued) 01251654 FIGURE 33. +5V to +12V Boost Regulator Figure 34 contains a table of standard inductors, by part number and corresponding manufacturer, for the fixed output regulator of Figure 33. Coilcraft (Note 20) Pulse (Note 21) Renco (Note 22) Schott (Note 23) Schott (Note 23) (Surface Mount) DO3316-153 PE-53898 RL-5471-7 67146510 67146540 Note 20: Coilcraft Inc., Phone: (800) 322-2645 1102 Silver Lake Road, Cary, IL 60013 Fax: (708) 639-1469 European Headquarters, 21 Napier Place Phone: +44 1236 730 595 Wardpark North, Cumbernauld, Scotland G68 0LL Note 21: Pulse Engineering Inc., 12220 World Trade Drive, San Diego, CA 92128 European Headquarters, Dunmore Road Tuam, Co. Galway, Ireland Fax: (619) 674-8262 Phone: +353 93 24 107 Fax: +353 93 24 459 Note 22: Renco Electronics Inc., Phone: (800) 645-5828 60 Jeffryn Blvd. East, Deer Park, NY 11729 Note 23: Schott Corp., Fax: +44 1236 730 627 Phone: (619) 674-8100 Fax: (516) 586-5562 Phone: (612) 475-1173 1000 Parkers Lane Road, Wayzata, MN 55391 Fax: (612) 475-1786 FIGURE 34. Inductor Selection Table www.national.com 22 LM2586 Typical Boost Regulator Applications (Continued) 01251655 FIGURE 35. +12V to +24V Boost Regulator 01251656 FIGURE 36. +24V to +36V Boost Regulator 23 www.national.com LM2586 Typical Boost Regulator Applications (Continued) 01251657 FIGURE 37. +24V to +48V Boost Regulator Note 24: The LM2586 will require a heat sink in these applications. The size of the heat sink will depend on the maximum ambient temperature. To calculate the thermal resistance of the IC and the size of the heat sink needed, see the “Heat Sink/Thermal Considerations” section in the Application Hints. Application Hints LM2586 SPECIAL FEATURES 01251658 FIGURE 38. Shutdown Operation FREQUENCY ADJUSTMENT The switching frequency of the LM2586 can be adjusted with the use of an external resistor. This feature allows the user to optimize the size of the magnetics and the output capacitor(s) by tailoring the operating frequency. A resistor connected from pin 1 (the Freq. Adj. pin) to ground will set the switching frequency from 100 kHz to 200 kHz (maximum). As shown in Figure 38, the pin can be used to adjust the frequency while still providing the shut down function. A curve in the Performance Characteristics Section graphs the resistor value to the corresponding switching frequency. The table in Figure 39 shows resistor values corresponding to commonly used frequencies. However, changing the LM2586’s operating frequency from its nominal value of 100 kHz will change the magnetics selection and compensation component values. SHUTDOWN CONTROL A feature of the LM2586 is its ability to be shut down using the ON /OFF pin (pin 1). This feature conserves input power by turning off the device when it is not in use. For proper operation, an isolation diode is required (as shown in Figure 38). The device will shut down when 3V or greater is applied on the ON /OFF pin, sourcing current into pin 1. In shut down mode, the device will draw typically 56 µA of supply current (16 µA to VIN and 40 µA to the ON /OFF pin). To turn the device back on, leave pin 1 floating, using an (isolation) diode, as shown in Figure 38 (for normal operation, do not source or sink current to or from this pin — see the next section). www.national.com 24 Use of this feature enables the LM2586 to be synchronized to an external oscillator, such as a system clock. This operation allows multiple power supplies to operate at the same frequency, thus eliminating frequency-related noise problems. (Continued) RSET(kΩ) Frequency (kHz) Open 100 200 125 47 150 33 175 22 200 FIGURE 39. Frequency Setting Resistor Guide 01251659 01251669 FIGURE 40. Frequency Synchronization FIGURE 41. Waveforms of a Synchronized 12V Boost Regulator FREQUENCY SYNCHRONIZATION Another feature of the LM2586 is the ability to synchronize the switching frequency to an external source, using the sync pin (pin 6). This feature allows the user to parallel multiple devices to deliver more output power. A negative falling pulse applied to the sync pin will synchronize the LM2586 to an external oscillator (see Figures 40, 41). The scope photo in Figure 41 shows a LM2586 12V Boost Regulator synchronized to a 200 kHz signal. There is a 700 ns delay between the falling edge of the sync signal and the turning on of the switch. 01251661 FIGURE 42. Boost Regulator For best temperature coefficient and stability with time, use 1% metal film resistors. PROGRAMMING OUTPUT VOLTAGE (SELECTING R1 AND R2) Referring to the adjustable regulator in Figure 42, the output voltage is programmed by the resistors R1 and R2 by the following formula: where VREF = 1.23V VOUT = VREF (1 + R1/R2) Resistors R1 and R2 divide the output voltage down so that it can be compared with the 1.23V internal reference. With R2 between 1k and 5k, R1 is: where VREF = 1.23V R1 = R2 (VOUT/VREF − 1) SHORT CIRCUIT CONDITION Due to the inherent nature of boost regulators, when the output is shorted (see Figure 42), current flows directly from the input, through the inductor and the diode, to the output, bypassing the switch. The current limit of the switch does not limit the output current for the entire circuit. To protect the load and prevent damage to the switch, the current must be externally limited, either by the input supply or at the output 25 www.national.com LM2586 Application Hints LM2586 Application Hints FLYBACK REGULATOR INPUT CAPACITORS (Continued) A flyback regulator draws discontinuous pulses of current from the input supply. Therefore, there are two input capacitors needed in a flyback regulator — one for energy storage and one for filtering (see Figure 43). Both are required due to the inherent operation of a flyback regulator. To keep a stable or constant voltage supply to the LM2586, a storage capacitor (≥100 µF) is required. If the input source is a rectified DC supply and/or the application has a wide temperature range, the required rms current rating of the capacitor might be very large. This means a larger value of capacitance or a higher voltage rating will be needed for the input capacitor. The storage capacitor will also attenuate noise which may interfere with other circuits connected to the same input supply voltage. with an external current limit circuit. The external limit should be set to the maximum switch current of the device, which is 3A. In a flyback regulator application (Figure 43), using the standard transformers, the LM2586 will survive a short circuit to the main output. When the output voltage drops to 80% of its nominal value, the frequency will drop to 25 kHz. With a lower frequency, off times are larger. With the longer off times, the transformer can release all of its stored energy before the switch turns back on. Hence, the switch turns on initially with zero current at its collector. In this condition, the switch current limit will limit the peak current, saving the device. 01251662 FIGURE 43. Flyback Regulator datasheet). The schematic in Figure 43 shows another method of clamping the switch voltage. A single voltage transient suppressor (the SA51A) is inserted at the switch pin. This method clamps the total voltage across the switch, not just the voltage across the primary. If poor circuit layout techniques are used (see the “Circuit Layout Guideline” section), negative voltage transients may appear on the Switch pin (pin 5). Applying a negative voltage (with respect to the IC’s ground) to any monolithic IC pin causes erratic and unpredictable operation of that IC. This holds true for the LM2586 IC as well. When used in a flyback regulator, the voltage at the Switch pin (pin 5) can go negative when the switch turns on. The “ringing” voltage at the switch pin is caused by the output diode capacitance and the transformer leakage inductance forming a resonant circuit at the secondary(ies). The resonant circuit generates the “ringing” voltage, which gets reflected back through the transformer to the switch pin. There are two common methods to avoid this problem. One is to add an RC snubber around the output rectifier(s), as in Figure 43. The values of the resistor and the capacitor must be chosen so that the voltage at the Switch pin does not drop below −0.4V. The resistor may In addition, a small bypass capacitor is required due to the noise generated by the input current pulses. To eliminate the noise, insert a 1.0 µF ceramic capacitor between VIN and ground as close as possible to the device. SWITCH VOLTAGE LIMITS In a flyback regulator, the maximum steady-state voltage appearing at the switch, when it is off, is set by the transformer turns ratio, N, the output voltage, VOUT, and the maximum input voltage, VIN (Max): VSW(OFF) = VIN (Max) + (VOUT +VF)/N where VF is the forward biased voltage of the output diode, and is typically 0.5V for Schottky diodes and 0.8V for ultrafast recovery diodes. In certain circuits, there exists a voltage spike, VLL, superimposed on top of the steady-state voltage (see Figure 5, waveform A). Usually, this voltage spike is caused by the transformer leakage inductance and/or the output rectifier recovery time. To “clamp” the voltage at the switch from exceeding its maximum value, a transient suppressor in series with a diode is inserted across the transformer primary (as shown in the circuit in Figure 4 and other flyback regulator circuits throughout the www.national.com 26 LM2586 Application Hints (Continued) range in value between 10Ω and 1 kΩ, and the capacitor will vary from 0.001 µF to 0.1 µF. Adding a snubber will (slightly) reduce the efficiency of the overall circuit. The other method to reduce or eliminate the “ringing” is to insert a Schottky diode clamp between pins 5 and 4 (ground), also shown in Figure 43. This prevents the voltage at pin 5 from dropping below −0.4V. The reverse voltage rating of the diode must be greater than the switch off voltage. Theoretically, the maximum output voltage can be as large as desired — just keep increasing the turns ratio of the transformer. However, there exists some physical limitations that prevent the turns ratio, and thus the output voltage, from increasing to infinity. The physical limitations are capacitances and inductances in the LM2586 switch, the output diode(s), and the transformer — such as reverse recovery time of the output diode (mentioned above). NOISY INPUT LINE CONDITION A small, low-pass RC filter should be used at the input pin of the LM2586 if the input voltage has an unusually large amount of transient noise, such as with an input switch that bounces. The circuit in Figure 44 demonstrates the layout of the filter, with the capacitor placed from the input pin to ground and the resistor placed between the input supply and the input pin. Note that the values of RIN and CIN shown in the schematic are good enough for most applications, but some readjusting might be required for a particular application. If efficiency is a major concern, replace the resistor with a small inductor (say 10 µH and rated at 200 mA). STABILITY All current-mode controlled regulators can suffer from an instability, known as subharmonic oscillation, if they operate with a duty cycle above 50%. To eliminate subharmonic oscillations, a minimum value of inductance is required to ensure stability for all boost and flyback regulators. The minimum inductance is given by: 01251663 FIGURE 44. Input Line Filter OUTPUT VOLTAGE LIMITATIONS The maximum output voltage of a boost regulator is the maximum switch voltage minus a diode drop. In a flyback regulator, the maximum output voltage is determined by the turns ratio, N, and the duty cycle, D, by the equation: VOUT ≈ N x VIN x D/(1 − D) The duty cycle of a flyback regulator is determined by the following equation: where VSAT is the switch saturation voltage and can be found in the Characteristic Curves. 01251664 FIGURE 45. Circuit Board Layout CIRCUIT LAYOUT GUIDELINES As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring inductance generate voltage transients which can cause problems. For minimal inductance and ground loops, keep the length of the leads and traces as short as possible. Use single point grounding or ground plane construction for best results. Separate the signal grounds from the power grounds (as 27 www.national.com LM2586 Application Hints Adding the junction temperature rise to the maximum ambient temperature gives the actual operating junction temperature: (Continued) indicated in Figure 45). When using the Adjustable version, physically locate the programming resistors as near the regulator IC as possible, to keep the sensitive feedback wiring short. TJ = ∆TJ + TA. If the operating junction temperature exceeds the maximum junction temperatue in item 3 above, then a heat sink is required. When using a heat sink, the junction temperature rise can be determined by the following: ∆TJ = PD • (θJC + θInterface + θHeat Sink) HEAT SINK/THERMAL CONSIDERATIONS In many cases, a heat sink is not required to keep the LM2586 junction temperature within the allowed operating temperature range. For each application, to determine whether or not a heat sink will be required, the following must be identified: 1) Maximum ambient temperature (in the application). Again, the operating junction temperature will be: TJ = ∆TJ + TA As before, if the maximum junction temperature is exceeded, a larger heat sink is required (one that has a lower thermal resistance). Included in the Switchers Made Simple ® design software is a more precise (non-linear) thermal model that can be used to determine junction temperature with different input-output parameters or different component values. It can also calculate the heat sink thermal resistance required to maintain the regulator junction temperature below the maximum operating temperature. 2) Maximum regulator power dissipation (in the application). 3) Maximum allowed junction temperature (125˚C for the LM2586). For a safe, conservative design, a temperature approximately 15˚C cooler than the maximum junction temperature should be selected (110˚C). 4) LM2586 package thermal resistances θJA and θJC (given in the Electrical Characteristics). Total power dissipated (PD) by the LM2586 can be estimated as follows: To further simplify the flyback regulator design procedure, National Semiconductor is making available computer design software to be used with the Simple Switcher ® line of switching regulators. Switchers Made Simple is available on a 31⁄2" diskette for IBM compatible computers from a National Semiconductor sales office in your area or the National Semiconductor Customer Response Center (1-800-272-9959). VIN is the minimum input voltage, VOUT is the output voltage, N is the transformer turns ratio, D is the duty cycle, and ILOAD is the maximum load current (and ∑ILOAD is the sum of the maximum load currents for multiple-output flyback regulators). The duty cycle is given by: where VF is the forward biased voltage of the diode and is typically 0.5V for Schottky diodes and 0.8V for fast recovery diodes. VSAT is the switch saturation voltage and can be found in the Characteristic Curves. When no heat sink is used, the junction temperature rise is: ∆TJ = PD • θJA. www.national.com 28 LM2586 Physical Dimensions inches (millimeters) unless otherwise noted Order Number LM2586T-3.3, LM2586T-5.0, LM2586T-12 or LM2586T-ADJ NS Package Number TA07B Order Number LM2586S-3.3, LM2586S-5.0, LM2586S-12 or LM2586S-ADJ Tape and Reel Order Number LM2586SX-3.3, LM2586SX-5.0, LM2586SX-12 or LM2586SX-ADJ NS Package Number TS7B 29 www.national.com LM2586 SIMPLE SWITCHER 3A Flyback Regulator with Shutdown Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560