TI LM2588S

LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
LM2588 SIMPLE SWITCHER® 5A Flyback Regulator with Shutdown
Check for Samples: LM2588
FEATURES
DESCRIPTION
• Requires Few External Components
• Family of Standard Inductors and
Transformers
• NPN Output Switches 5.0A, Can Stand Off 65V
• Wide Input Voltage Range: 4V to 40V
• Adjustable Switching Frequency: 100 kHz to
200 kHz
• External Shutdown Capability
• Draws Less Than 60 μA When Shut Down
• Frequency Synchronization
• Current-mode Operation for Improved
Transient Response, Line Regulation, and
Current Limit
• Internal Soft-start Function Reduces In-rush
Current During Start-up
• Output Transistor Protected by Current Limit,
Under Voltage Lockout, and Thermal
Shutdown
• System Output Voltage Tolerance of ±4% Max
Over Line and Load Conditions
The LM2588 series of regulators are monolithic
integrated circuits specifically designed for flyback,
step-up (boost), and forward converter applications.
The device is available in 4 different output voltage
versions: 3.3V, 5.0V, 12V, and adjustable.
1
2345
TYPICAL APPLICATIONS
•
•
•
•
Flyback Regulator
Forward Converter
Multiple-output Regulator
Simple Boost Regulator
Requiring a minimum number of external
components, these regulators are cost effective, and
simple to use. Included in the datasheet are typical
circuits of boost and flyback regulators. Also listed
are selector guides for diodes and capacitors and a
family of standard inductors and flyback transformers
designed to work with these switching regulators.
The power switch is a 5.0A NPN device that can
stand-off 65V. Protecting the power switch are current
and thermal limiting circuits, and an undervoltage
lockout circuit. This IC contains an adjustable
frequency oscillator that can be programmed up to
200 kHz. The oscillator can also be synchronized with
other devices, so that multiple devices can operate at
the same switching frequency.
Other features include soft start mode to reduce inrush current during start up, and current mode control
for improved rejection of input voltage and output
load transients and cycle-by-cycle current limiting.
The device also has a shutdown pin, so that it can be
turned off externally. An output voltage tolerance of
±4%, within specified input voltages and output load
conditions, is ensured for the power supply system.
Connection Diagrams
7-Pin
Top View
Bent, 7-Pin
Side View
Figure 1. LM2588T-12 or LM2588T-ADJ
See Package Number NDZ0007B
1
2
3
4
5
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Switchers Made Simple is a trademark of Texas Instruments.
SIMPLE SWITCHER is a registered trademark of Texas Instruments.
Switchers Made Simple is a registered trademark of dcl_owner.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1998–2013, Texas Instruments Incorporated
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
7-Pin
Top View
7-Pin
Side View
Figure 2. LM2588S-12 or LM2588S-ADJ
See Package Number KTW0007B
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
Absolute Maximum Ratings (1) (2)
−0.4V ≤ VIN ≤ 45V
Input Voltage
−0.4V ≤ VSW ≤ 65V
Switch Voltage
Switch Current (3)
Internally Limited
Compensation Pin Voltage
−0.4V ≤ VCOMP ≤ 2.4V
Feedback Pin Voltage
−0.4V ≤ VFB ≤ 2 VOUT
−0.4V ≤ VSH ≤ 6V
ON /OFF Pin Voltage
−0.4V ≤ VSYNC ≤ 2V
Sync Pin Voltage
Power Dissipation (4)
Internally Limited
Storage Temperature Range
−65°C to +150°C
Lead Temperature
Maximum Junction Temperature
(Soldering, 10 sec.)
Minimum ESD Rating
(1)
(2)
(3)
(4)
260°C
(4)
150°C
(C = 100 pF, R = 1.5 kΩ)
2 kV
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. These ratings apply when the current is
limited to less than 1.2 mA for pins 1, 2, 3, and 6. Operating ratings indicate conditions for which the device is intended to be functional,
but device parameter specifications may not be ensured under these conditions. For ensured specifications and test conditions, see the
Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
Note that switch current and output current are not identical in a step-up regulator. Output current cannot be internally limited when the
LM2588 is used as a step-up regulator. To prevent damage to the switch, the output current must be externally limited to 5A. However,
output current is internally limited when the LM2588 is used as a flyback regulator (see the Application Hints section for more
information).
The junction temperature of the device (TJ) is a function of the ambient temperature (TA), the junction-to-ambient thermal resistance
(θJA), and the power dissipation of the device (PD). A thermal shutdown will occur if the temperature exceeds the maximum junction
temperature of the device: PD × θJA + TA(MAX) ≥ TJ(MAX). For a safe thermal design, check that the maximum power dissipated by the
device is less than: PD ≤ [TJ(MAX) − TA(MAX)]/θJA. When calculating the maximum allowable power dissipation, derate the maximum
junction temperature—this ensures a margin of safety in the thermal design.
Operating Ratings
4V ≤ VIN ≤ 40V
Supply Voltage
0V ≤ VSW ≤ 60V
Output Switch Voltage
ISW ≤ 5.0A
Output Switch Current
−40°C ≤ TJ ≤ +125°C
Junction Temperature Range
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
3
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
LM2588-3.3 Electrical Characteristics
Specifications with standard type face are for TJ = 25°C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V.
Symbol
Parameters
Conditions
Typical
Min
Max
Units
3.17/3.14
3.43/3.46
V
SYSTEM PARAMETERS Test Circuit of Figure 18 (1)
VOUT
Output Voltage
VIN = 4V to 12V
ILOAD = 400 mA to 1.75A
3.3
ΔVOUT/
ΔVIN
Line Regulation
VIN = 4V to 12V
ILOAD = 400 mA
20
50/100
mV
ΔVOUT/
ΔILOAD
Load Regulation
VIN = 12V
ILOAD = 400 mA to 1.75A
20
50/100
mV
η
Efficiency
VIN = 12V, ILOAD = 1A
75
Measured at Feedback Pin
VCOMP = 1.0V
3.3
UNIQUE DEVICE PARAMETERS
VREF
Output Reference
Voltage
ΔVREF
Reference Voltage Line VIN = 4V to 40V
Regulation
GM
Error Amp
Transconductance
ICOMP = −30 μA to +30 μA
VCOMP = 1.0V
AVOL
Error Amp Voltage
Gain
VCOMP = 0.5V to 1.6V
RCOMP = 1.0 MΩ (3)
(1)
(2)
(3)
4
%
(2)
3.242/3.234
3.358/3.366
2.0
V
mV
1.193
0.678
260
151/75
2.259
mmho
V/V
External components such as the diode, inductor, input and output capacitors can affect switching regulator performance. When the
LM2588 is used as shown in Figure 18 and Figure 19, system performance will be as specified by the system parameters.
All room temperature limits are 100% production tested, and all limits at temperature extremes are specified via correlation using
standard Statistical Quality Control (SQC) methods.
A 1.0 MΩ resistor is connected to the compensation pin (which is the error amplifier output) to ensure accuracy in measuring AVOL.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
LM2588-5.0 Electrical Characteristics
Specifications with standard type face are for TJ = 25°C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V.
Symbol
Parameters
Conditions
Typical
Min
Max
Units
4.80/4.75
5.20/5.25
V
SYSTEM PARAMETERS Test Circuit of Figure 18 (1)
VOUT
Output Voltage
VIN = 4V to 12V
ILOAD = 500 mA to 1.45A
5.0
ΔVOUT/
ΔVIN
Line Regulation
VIN = 4V to 12V
ILOAD = 500 mA
20
50/100
mV
ΔVOUT/
ΔILOAD
Load Regulation
VIN = 12V
ILOAD = 500 mA to 1.45A
20
50/100
mV
η
Efficiency
VIN = 12V, ILOAD = 750 mA
80
Measured at Feedback Pin
VCOMP = 1.0V
5.0
UNIQUE DEVICE PARAMETERS
VREF
Output Reference
Voltage
ΔVREF
Reference Voltage Line VIN = 4V to 40V
Regulation
GM
Error Amp
Transconductance
ICOMP = −30 μA to +30 μA
VCOMP = 1.0V
AVOL
Error Amp Voltage
Gain
VCOMP = 0.5V to 1.6V
RCOMP = 1.0 MΩ (3)
(1)
(2)
(3)
%
(2)
4.913/4.900
5.088/5.100
V
3.3
mV
0.750
0.447
165
99/49
1.491
mmho
V/V
External components such as the diode, inductor, input and output capacitors can affect switching regulator performance. When the
LM2588 is used as shown in Figure 18 and Figure 19, system performance will be as specified by the system parameters.
All room temperature limits are 100% production tested, and all limits at temperature extremes are specified via correlation using
standard Statistical Quality Control (SQC) methods.
A 1.0 MΩ resistor is connected to the compensation pin (which is the error amplifier output) to ensure accuracy in measuring AVOL.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
5
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
LM2588-12 Electrical Characteristics
Specifications with standard type face are for TJ = 25°C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V.
Symbol
Parameters
Conditions
Typical
Min
Max
Units
12.0
11.52/11.40
12.48/12.60
V
20
100/200
mV
20
100/200
mV
SYSTEM PARAMETERS Test Circuit of Figure 19 (1)
VOUT
Output Voltage
VIN = 4V to 10V
ILOAD = 300 mA to 1.2A
ΔVOUT/
ΔVIN
Line Regulation
ΔVOUT/
ΔILOAD
Load Regulation
η
Efficiency
ILOAD = 300 mA
VIN = 10V
ILOAD = 300 mA to 1.2A
UNIQUE DEVICE PARAMETERS
VREF
VIN = 4V to 10V
Output Reference
Voltage
VIN = 10V, ILOAD = 1A
Measured at Feedback Pin
Reference Voltage Line VIN = 4V to 40V
Regulation
GM
Error Amp
Transconductance
ICOMP = −30 μA to +30 μA
Error Amp Voltage
Gain
VCOMP = 0.5V to 1.6V
(1)
(2)
(3)
6
%
12.0
11.79/11.76
12.21/12.24
V
VCOMP = 1.0V
ΔVREF
AVOL
90
(2)
7.8
mV
0.328
0.186
70
41/21
0.621
mmho
VCOMP = 1.0V
V/V
RCOMP = 1.0 MΩ (3)
External components such as the diode, inductor, input and output capacitors can affect switching regulator performance. When the
LM2588 is used as shown in Figure 18 and Figure 19, system performance will be as specified by the system parameters.
All room temperature limits are 100% production tested, and all limits at temperature extremes are specified via correlation using
standard Statistical Quality Control (SQC) methods.
A 1.0 MΩ resistor is connected to the compensation pin (which is the error amplifier output) to ensure accuracy in measuring AVOL.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
LM2588-ADJ Electrical Characteristics
Specifications with standard type face are for TJ = 25°C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V.
Symbol
Parameters
Conditions
Typical
Min
Max
Units
12.0
11.52/11.40
12.48/12.60
V
SYSTEM PARAMETERS Test Circuit of Figure 19 (1)
VOUT
Output Voltage
VIN = 4V to 10V
ILOAD = 300 mA to 1.2A
ΔVOUT/
ΔVIN
Line Regulation
VIN = 4V to 10V
ILOAD = 300 mA
20
100/200
mV
ΔVOUT/
ΔILOAD
Load Regulation
VIN = 10V
ILOAD = 300 mA to 1.2A
20
100/200
mV
η
Efficiency
VIN = 10V, ILOAD = 1A
90
UNIQUE DEVICE PARAMETERS
VREF
Output Reference
Voltage
ΔVREF
Reference Voltage Line VIN = 4V to 40V
Regulation
GM
Error Amp
Transconductance
ICOMP = −30 μA to +30 μA
VCOMP = 1.0V
AVOL
Error Amp Voltage
Gain
IB
Error Amp Input Bias
Current
(1)
%
(2)
Measured at Feedback Pin
VCOMP = 1.0V
1.230
1.208/1.205
1.252/1.255
V
1.5
mV
3.200
1.800
VCOMP = 0.5V to 1.6V
RCOMP = 1.0 MΩ (3)
670
400/200
VCOMP = 1.0V
125
6.000
mmho
V/V
425/600
nA
External components such as the diode, inductor, input and output capacitors can affect switching regulator performance. When the
LM2588 is used as shown in Figure 18 and Figure 19, system performance will be as specified by the system parameters.
All room temperature limits are 100% production tested, and all limits at temperature extremes are specified via correlation using
standard Statistical Quality Control (SQC) methods.
A 1.0 MΩ resistor is connected to the compensation pin (which is the error amplifier output) to ensure accuracy in measuring AVOL.
(2)
(3)
All Output Voltage Versions Electrical Characteristics (1)
Specifications with standard type face are for TJ = 25°C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V.
Symbol
IS
Parameters
Input Supply Current
Max
Units
Switch Off (2)
Conditions
Typical
11
Min
15.5/16.5
mA
ISWITCH = 3.0A
85
140/165
mA
16
100/300
μA
IS/D
Shutdown Input
Supply Current
VSH = 3V
VUV
Input Supply
Undervoltage Lockout
RLOAD = 100Ω
3.30
3.05
3.75
V
fO
Oscillator Frequency
Measured at Switch Pin
RLOAD = 100Ω, VCOMP = 1.0V
Freq. Adj. Pin Open (Pin 1)
100
85/75
115/125
kHz
RSET = 22 kΩ
200
kHz
25
kHz
fSC
Short-Circuit Frequency Measured at Switch Pin
RLOAD = 100Ω
VFEEDBACK = 1.15V
VEAO
Error Amplifier Output
Swing
(1)
(2)
(3)
Upper Limit (3)
2.8
Lower Limit (2)
0.25
2.6/2.4
V
0.40/0.55
V
All room temperature limits are 100% production tested, and all limits at temperature extremes are specified via correlation using
standard Statistical Quality Control (SQC) methods.
To measure this parameter, the feedback voltage is set to a high value, depending on the output version of the device, to force the error
amplifier output low and the switch off.
To measure this parameter, the feedback voltage is set to a low value, depending on the output version of the device, to force the error
amplifier output high and the switch on.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
7
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
All Output Voltage Versions Electrical Characteristics(1) (continued)
Specifications with standard type face are for TJ = 25°C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V.
Typical
Min
Max
Units
IEAO
Symbol
Error Amp Output
Current (Source or
Sink)
Parameters
See (4)
Conditions
165
110/70
260/320
μA
ISS
Soft Start Current
VFEEDBACK = 0.92V
VCOMP = 1.0V
11.0
8.0/7.0
17.0/19.0
μA
DMAX
Maximum Duty Cycle
RLOAD = 100Ω (3)
98
93/90
IL
Switch Leakage
Current
Switch Off
VSWITCH = 60V
15
VSUS
Switch Sustaining
Voltage
dV/dT = 1.5V/ns
VSAT
Switch Saturation
Voltage
ISWITCH = 5.0A
ICL
NPN Switch Current
Limit
VSTH
Synchronization
Threshold Voltage
ISYNC
Synchronization
Pin Current
300/600
65
0.7
μA
V
1.1/1.4
V
6.5
5.0
9.5
A
FSYNC = 200 kHz
VCOMP = 1V, VIN = 5V
0.75
0.625/0.40
0.875/1.00
V
VIN = 5V
VCOMP = 1V, VSYNC = VSTH
100
200
μA
VSHTH
ON /OFF Pin (Pin 1)
Threshold Voltage
VCOMP = 1V
ISH
ON /OFF Pin (Pin 1)
Current
θJA
θJA
θJC
Thermal Resistance
θJA
θJA
θJA
θJC
%
(5)
1.6
1.0/0.8
2.2/2.4
V
VCOMP = 1V
VSH = VSHTH
40
15/10
65/75
μA
NDZ Package, Junction to Ambient (6)
NDZ Package, Junction to Ambient (7)
NDZ Package, Junction to Case
65
45
2
KTW Package, Junction to Ambient (8)
KTW Package, Junction to Ambient (9)
KTW Package, Junction to
Ambient (10)
KTW Package, Junction to Case
56
35
26
2
°C/W
(4)
To measure the worst-case error amplifier output current, the LM2588 is tested with the feedback voltage set to its low value (specified
in Note 3 under the All Output Voltage Versions Electrical Characteristics() table) and at its high value (specified in Note 2 under the All
Output Voltage Versions Electrical Characteristics() table).
(5) When testing the minimum value, do not sink current from this pin—isolate it with a diode. If current is drawn from this pin, the frequency
adjust circuit will begin operation (see Figure 54).
(6) Junction to ambient thermal resistance (no external heat sink) for the 7 lead TO-220 package mounted vertically, with ½ inch leads in a
socket, or on a PC board with minimum copper area.
(7) Junction to ambient thermal resistance (no external heat sink) for the 7 lead TO-220 package mounted vertically, with ½ inch leads
soldered to a PC board containing approximately 4 square inches of (1 oz.) copper area surrounding the leads.
(8) Junction to ambient thermal resistance for the 7 lead TO-263 mounted horizontally against a PC board area of 0.136 square inches (the
same size as the TO-263 package) of 1 oz. (0.0014 in. thick) copper.
(9) Junction to ambient thermal resistance01242001 for the 7 lead TO-263 mounted horizontally against a PC board area of 0.4896 square
inches (3.6 times the area of the TO-263 package) of 1 oz. (0.0014 in. thick) copper.
(10) Junction to ambient thermal resistance for the 7 lead TO-263 mounted horizontally against a PC board copper area of 1.0064 square
inches (7.4 times the area of the TO-263 package) of 1 oz. (0.0014 in. thick) copper. Additional copper area will reduce thermal
resistance further. See the thermal model in Switchers Made Simple® software.
8
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
Typical Performance Characteristics
Supply Current
vs Temperature
Reference Voltage
vs Temperature
Figure 3.
Figure 4.
ΔReference Voltage
vs Supply Voltage
Supply Current
vs Switch Current
Figure 5.
Figure 6.
Current Limit
vs Temperature
Feedback Pin Bias
Current
vs
Temperature
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
9
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
10
Switch Saturation
Voltage
vs
Temperature
Switch Transconductance
vs Temperature
Figure 9.
Figure 10.
Oscillator Frequency
vs Temperature
Error Amp Transconductance
vs Temperature
Figure 11.
Figure 12.
Error Amp Voltage
Gain
vs
Temperature
Short Circuit Frequency
vs Temperature
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
Typical Performance Characteristics (continued)
Shutdown Supply Current
vs Temperature
ON /OFF Pin Current
vs Voltage
Figure 15.
Figure 16.
Oscillator Frequency
vs Resistance
Figure 17.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
11
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
Flyback Regulator
Test Circuits
CIN1—100 μF, 25V Aluminum ElectrolyticCIN2—0.1 μF CeramicT—22 μH, 1:1 Schott
#67141450D—1N5820COUT—680 μF, 16V Aluminum ElectrolyticCC—0.47 μF CeramicRC—2k
Figure 18. LM2588-3.3 and LM2588-5.0
12
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
CIN1—100 μF, 25V Aluminum ElectrolyticCIN2—0.1 μF CeramicL—15 μH, Renco #RL-5472-5D—1N5820COUT—680
μF, 16V Aluminum ElectrolyticCC—0.47 μF CeramicRC—2kFor 12V Devices: R1 = Short (0Ω) andR2 = OpenFor ADJ
Devices: R1 = 48.75k, ±0.1% andR2 = 5.62k, ±0.1%
Figure 19. LM2588-12 and LM2588-ADJ
Block Diagram
For Fixed Versions 3.3V, R1 = 3.4k, R2 = 2k5.0V, R1 = 6.15k, R2 = 2k12V, R1 = 8.73k, R2 = 1kFor Adj. VersionR1 =
Short (0Ω), R2 = Open
Flyback Regulator Operation
The LM2588 is ideally suited for use in the flyback regulator topology. The flyback regulator can produce a single
output voltage, such as the one shown in Figure 20, or multiple output voltages. In Figure 20, the flyback
regulator generates an output voltage that is inside the range of the input voltage. This feature is unique to
flyback regulators and cannot be duplicated with buck or boost regulators.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
13
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
The operation of a flyback regulator is as follows (refer to Figure 20): when the switch is on, current flows
through the primary winding of the transformer, T1, storing energy in the magnetic field of the transformer. Note
that the primary and secondary windings are out of phase, so no current flows through the secondary when
current flows through the primary. When the switch turns off, the magnetic field collapses, reversing the voltage
polarity of the primary and secondary windings. Now rectifier D1 is forward biased and current flows through it,
releasing the energy stored in the transformer. This produces voltage at the output.
The output voltage is controlled by modulating the peak switch current. This is done by feeding back a portion of
the output voltage to the error amp, which amplifies the difference between the feedback voltage and a 1.230V
reference. The error amp output voltage is compared to a ramp voltage proportional to the switch current (i.e.,
inductor current during the switch on time). The comparator terminates the switch on time when the two voltages
are equal, thereby controlling the peak switch current to maintain a constant output voltage.
As shown in Figure 20, the LM2588 can be used as a flyback regulator by using a minimum number of external
components. The switching waveforms of this regulator are shown in Figure 21. Typical Performance Characteristics
observed during the operation of this circuit are shown in Figure 22.
Figure 20. 12V Flyback Regulator Design Example
14
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
Typical Performance Characteristics
A: Switch Voltage, 10V/div
B: Switch Current, 5A/div
C: Output Rectifier Current, 5A/div
D: Output Ripple Voltage, 100 mV/div
AC-Coupled
Figure 21. Switching Waveforms
Figure 22. VOUT Response to Load Current Step
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
15
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
Typical Flyback Regulator Applications
Figure 23 through Figure 28 show six typical flyback applications, varying from single output to triple output. Each
drawing contains the part number(s) and manufacturer(s) for every component except the transformer. For the
transformer part numbers and manufacturers' names, see Table 1. For applications with different output
voltages—requiring the LM2588-ADJ—or different output configurations that do not match the standard
configurations, refer to the Switchers Made Simple™ software.
Figure 23. Single-Output Flyback Regulator
Figure 24. Single-Output Flyback Regulator
16
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
Figure 25. Single-Output Flyback Regulator
Figure 26. Dual-Output Flyback Regulator
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
17
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
Figure 27. Dual-Output Flyback Regulator
Figure 28. Triple-Output Flyback Regulator
TRANSFORMER SELECTION (T)
Table 1 lists the standard transformers available for flyback regulator applications. Included in the table are the
turns ratio(s) for each transformer, as well as the output voltages, input voltage ranges, and the maximum load
currents for each circuit.
18
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
Table 1. Transformer Selection Table
Applications
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Transformers
T1
T1
T1
T2
T3
T4
18V–36V
VIN
4V–6V
4V–6V
8V–16V
4V–6V
18V–36V
VOUT1
3.3V
5V
12V
12V
12V
5V
IOUT1 (Max)
1.8A
1.4A
1.2A
0.3A
1A
2.5A
1
1
1
2.5
0.8
0.35
VOUT2
−12V
−12V
12V
IOUT2 (Max)
0.3A
1A
0.5A
2.5
0.8
0.8
N1
N2
VOUT3
−12V
IOUT3 (Max)
0.5A
N3
0.8
Table 2. Transformer Manufacturer Guide
Transformer
Type
(1)
(2)
(3)
(4)
Manufacturers' Part Numbers
Coilcraft (1)
Coilcraft Surface Mount (1) Pulse Surface Mount (2)
Renco (3)
Schott (4)
T1
Q4434-B
Q4435-B
PE-68411
RL-5530
67141450
T2
Q4337-B
Q4436-B
PE-68412
RL-5531
67140860
T3
Q4343-B
—
PE-68421
RL-5534
67140920
T4
Q4344-B
—
PE-68422
RL-5535
67140930
Coilcraft Inc.,: Phone: (800) 322-26451102 Silver Lake Road, Cary, IL 60013: Fax: (708) 639-1469European Headquarters, 21
Napier Place: Phone: +44 1236 730 595Wardpark North, Cumbernauld, Scotland G68 0LL: Fax: +44 1236 730 627
Pulse Engineering Inc.,: Phone: (619) 674-810012220 World Trade Drive, San Diego, CA 92128: Fax: (619) 674-8262European
Headquarters, Dunmore Road: Phone: +353 93 24 107Tuam, Co. Galway, Ireland: Fax: +353 93 24 459
Renco Electronics Inc.,: Phone: (800) 645-582860 Jeffryn Blvd. East, Deer Park, NY 11729: Fax: (516) 586-5562
Schott Corp.,: Phone: (612) 475-11731000 Parkers Lane Road, Wayzata, MN 55391: Fax: (612) 475-1786
TRANSFORMER FOOTPRINTS
Figure 29 through Figure 46 show the footprints of each transformer, listed in Table 2.
Figure 29. T1 - Top View
Coilcraft Q4434-B
Figure 30. T2 - Top View
Coilcraft Q4337-B
Figure 31. T3 - Top View
Coilcraft Q4343-B
Figure 32. T4 - Top View
Coilcraft Q4344-B
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
19
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
20
www.ti.com
Figure 33. T1 - Top View
Coilcraft Q4435-B
(Surface Mount)
Figure 34. T2 - Top View
Coilcraft Q4436-B
(Surface Mount)
Figure 35. T1 - Top View
Pulse PE-68411
(Surface Mount)
Figure 36. T2 - Top View
Pulse PE-68412
(Surface Mount)
Figure 37. T3 - Top View
Pulse PE-68421
(Surface Mount)
Figure 38. T4 - Top View
Pulse PE-68422
(Surface Mount)
Figure 39. T1 - Top View
Renco RL-5530
Figure 40. T2 - Top View
Renco RL-5531
Figure 41. T3 - Top View
Renco RL-5534
Figure 42. T4 - Top View
Renco RL-5535
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
Figure 43. T1 - Top View
Schott 67141450
Figure 44. T2 - Top View
Schott 67140860
Figure 45. T3 - Top View
Schott 67140920
Figure 46. T4 - Top View
Schott 67140930
Step-Up (Boost) Regulator Operation
Figure 47 shows the LM2588 used as a step-up (boost) regulator. This is a switching regulator that produces an
output voltage greater than the input supply voltage.
A brief explanation of how the LM2588 Boost Regulator works is as follows (refer to Figure 47). When the NPN
switch turns on, the inductor current ramps up at the rate of VIN/L, storing energy in the inductor. When the
switch turns off, the lower end of the inductor flies above VIN, discharging its current through diode (D) into the
output capacitor (COUT) at a rate of (VOUT − VIN)/L. Thus, energy stored in the inductor during the switch on time
is transferred to the output during the switch off time. The output voltage is controlled by adjusting the peak
switch current, as described in the Flyback Regulator section.
Figure 47. 12V Boost Regulator
By adding a small number of external components (as shown in Figure 47), the LM2588 can be used to produce
a regulated output voltage that is greater than the applied input voltage. The switching waveforms observed
during the operation of this circuit are shown in Figure 48. Typical performance of this regulator is shown in
Figure 49.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
21
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
A: Switch Voltage,10V/div
B: Switch Current, 5A/div
C: Inductor Current, 5A/div
D: Output Ripple Voltage,
100 mV/div, AC-Coupled
Figure 48. Switching Waveforms
Figure 49. VOUT Response to Load Current Step
22
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
TYPICAL BOOST REGULATOR APPLICATIONS
Figure 50 and Figure 51 through Figure 53 show four typical boost applications—one fixed and three using the
adjustable version of the LM2588. Each drawing contains the part number(s) and manufacturer(s) for every
component. For the fixed 12V output application, the part numbers and manufacturers' names for the inductor
are listed in a table in Table 3. For applications with different output voltages, refer to the Switchers Made
Simple™software.
Figure 50. +5V to +12V Boost Regulator
Table 3 contains a table of standard inductors, by part number and corresponding manufacturer, for the fixed
output regulator of Figure 50.
Table 3. Inductor Selection Table
Coilcraft
(1)
Pulse
R4793-A
(1)
(2)
(3)
(4)
(2)
PE-53900
Renco
(3)
RL-5472-5
Schott
(4)
67146520
Coilcraft Inc.,: Phone: (800) 322-26451102 Silver Lake Road, Cary, IL 60013: Fax: (708) 639-1469European Headquarters, 21
Napier Place: Phone: +44 1236 730 595Wardpark North, Cumbernauld, Scotland G68 0LL: Fax: +44 1236 730 627
Pulse Engineering Inc.,: Phone: (619) 674-810012220 World Trade Drive, San Diego, CA 92128: Fax: (619) 674-8262European
Headquarters, Dunmore Road: Phone: +353 93 24 107Tuam, Co. Galway, Ireland: Fax: +353 93 24 459
Renco Electronics Inc.,: Phone: (800) 645-582860 Jeffryn Blvd. East, Deer Park, NY 11729: Fax: (516) 586-5562
Schott Corp.,: Phone: (612) 475-11731000 Parkers Lane Road, Wayzata, MN 55391: Fax: (612) 475-1786
Figure 51. +12V to +24V Boost Regulator
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
23
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
Figure 52. +24V to +36V Boost Regulator
*The LM2588 will require a heat sink in these applications. The size of the heat sink will depend on the maximum
ambient temperature. To calculate the thermal resistance of the IC and the size of the heat sink needed, see the
HEAT SINK/THERMAL CONSIDERATIONS section in the Application Hints.
Figure 53. +24V to +48V Boost Regulator
Application Hints
LM2588 SPECIAL FEATURES
Figure 54. Shutdown Operation
SHUTDOWN CONTROL
A feature of the LM2588 is its ability to be shut down using the ON /OFF pin (pin 1). This feature conserves input
power by turning off the device when it is not in use. For proper operation, an isolation diode is required (as
shown in Figure 54).
24
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
The device will shut down when 3V or greater is applied on the ON /OFF pin, sourcing current into pin 1. In shut
down mode, the device will draw typically 56 μA of supply current (16 μA to VIN and 40 μA to the ON /OFF pin).
To turn the device back on, leave pin 1 floating, using an (isolation) diode, as shown in Figure 54 (for normal
operation, do not source or sink current to or from this pin—see the next section).
FREQUENCY ADJUSTMENT
The switching frequency of the LM2588 can be adjusted with the use of an external resistor. This feature allows
the user to optimize the size of the magnetics and the output capacitor(s) by tailoring the operating frequency. A
resistor connected from pin 1 (the Freq. Adj. pin) to ground will set the switching frequency from 100 kHz to 200
kHz (maximum). As shown in Figure 54, the pin can be used to adjust the frequency while still providing the shut
down function. A curve in the Performance Characteristics Section graphs the resistor value to the corresponding
switching frequency. The table in Table 4 shows resistor values corresponding to commonly used frequencies.
However, changing the LM2588's operating frequency from its nominal value of 100 kHz will change the
magnetics selection and compensation component values.
Table 4. Frequency Setting Resistor Guide
RSET(kΩ)
Frequency (kHz)
Open
100
200
125
47
150
33
175
22
200
Figure 55. Frequency Synchronization
FREQUENCY SYNCHRONIZATION
Another feature of the LM2588 is the ability to synchronize the switching frequency to an external source, using
the sync pin (pin 6). This feature allows the user to parallel multiple devices to deliver more output power.
A negative falling pulse applied to the sync pin will synchronize the LM2588 to an external oscillator (see
Figure 55 and Figure 56).
Use of this feature enables the LM2588 to be synchronized to an external oscillator, such as a system clock. This
operation allows multiple power supplies to operate at the same frequency, thus eliminating frequency-related
noise problems.
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
25
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
Figure 56. Waveforms of a Synchronized
12V Boost Regulator
The scope photo in Figure 56 shows a LM2588 12V Boost Regulator synchronized to a 200 kHz signal. There is
a 700 ns delay between the falling edge of the sync signal and the turning on of the switch.
PROGRAMMING OUTPUT VOLTAGE
(SELECTING R1 AND R2)
Referring to the adjustable regulator in Figure 57, the output voltage is programmed by the resistors R1 and R2
by the following formula:
VOUT = VREF (1 + R1/R2)
where VREF = 1.23V
(1)
Resistors R1 and R2 divide the output voltage down so that it can be compared with the 1.23V internal
reference. With R2 between 1k and 5k, R1 is:
R1 = R2 (VOUT/VREF − 1)
where VREF = 1.23V
(2)
For best temperature coefficient and stability with time, use 1% metal film resistors.
SHORT CIRCUIT CONDITION
Due to the inherent nature of boost regulators, when the output is shorted (see Figure 57 ), current flows directly
from the input, through the inductor and the diode, to the output, bypassing the switch. The current limit of the
switch does not limit the output current for the entire circuit. To protect the load and prevent damage to the
switch, the current must be externally limited, either by the input supply or at the output with an external current
limit circuit. The external limit should be set to the maximum switch current of the device, which is 5A.
In a flyback regulator application (Figure 58 ), using the standard transformers, the LM2588 will survive a short
circuit to the main output. When the output voltage drops to 80% of its nominal value, the frequency will drop to
25 kHz. With a lower frequency, off times are larger. With the longer off times, the transformer can release all of
its stored energy before the switch turns back on. Hence, the switch turns on initially with zero current at its
collector. In this condition, the switch current limit will limit the peak current, saving the device.
26
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
Figure 57. Boost Regulator
Figure 58. Flyback Regulator
FLYBACK REGULATOR INPUT CAPACITORS
A flyback regulator draws discontinuous pulses of current from the input supply. Therefore, there are two input
capacitors needed in a flyback regulator—one for energy storage and one for filtering (see Figure 58). Both are
required due to the inherent operation of a flyback regulator. To keep a stable or constant voltage supply to the
LM2588, a storage capacitor (≥100 μF) is required. If the input source is a recitified DC supply and/or the
application has a wide temperature range, the required rms current rating of the capacitor might be very large.
This means a larger value of capacitance or a higher voltage rating will be needed for the input capacitor. The
storage capacitor will also attenuate noise which may interfere with other circuits connected to the same input
supply voltage.
In addition, a small bypass capacitor is required due to the noise generated by the input current pulses. To
eliminate the noise, insert a 1.0 μF ceramic capacitor between VIN and ground as close as possible to the device.
SWITCH VOLTAGE LIMITS
In a flyback regulator, the maximum steady-state voltage appearing at the switch, when it is off, is set by the
transformer turns ratio, N, the output voltage, VOUT, and the maximum input voltage, VIN (Max):
VSW(OFF) = VIN (Max) + (VOUT +VF)/N
(3)
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
27
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
where VF is the forward biased voltage of the output diode, and is typically 0.5V for Schottky diodes and 0.8V for
ultra-fast recovery diodes. In certain circuits, there exists a voltage spike, VLL, superimposed on top of the
steady-state voltage (see Figure 21, waveform A). Usually, this voltage spike is caused by the transformer
leakage inductance and/or the output rectifier recovery time. To “clamp” the voltage at the switch from exceeding
its maximum value, a transient suppressor in series with a diode is inserted across the transformer primary (as
shown in the circuit in Figure 20 and other flyback regulator circuits throughout the datasheet). The schematic in
Figure 58 shows another method of clamping the switch voltage. A single voltage transient suppressor (the
SA51A) is inserted at the switch pin. This method clamps the total voltage across the switch, not just the voltage
across the primary.
If poor circuit layout techniques are used (see the CIRCUIT LAYOUT GUIDELINES section), negative voltage
transients may appear on the Switch pin (pin 5). Applying a negative voltage (with respect to the IC's ground) to
any monolithic IC pin causes erratic and unpredictable operation of that IC. This holds true for the LM2588 IC as
well. When used in a flyback regulator, the voltage at the Switch pin (pin 5) can go negative when the switch
turns on. The “ringing” voltage at the switch pin is caused by the output diode capacitance and the transformer
leakage inductance forming a resonant circuit at the secondary(ies). The resonant circuit generates the “ringing”
voltage, which gets reflected back through the transformer to the switch pin. There are two common methods to
avoid this problem. One is to add an RC snubber around the output rectifier(s), as in Figure 58. The values of the
resistor and the capacitor must be chosen so that the voltage at the Switch pin does not drop below −0.4V. The
resistor may range in value between 10Ω and 1 kΩ, and the capacitor will vary from 0.001 μF to 0.1 μF. Adding a
snubber will (slightly) reduce the efficiency of the overall circuit.
The other method to reduce or eliminate the “ringing” is to insert a Schottky diode clamp between pins 5 and 4
(ground), also shown in Figure 58. This prevents the voltage at pin 5 from dropping below −0.4V. The reverse
voltage rating of the diode must be greater than the switch off voltage.
Figure 59. Input Line Filter
OUTPUT VOLTAGE LIMITATIONS
The maximum output voltage of a boost regulator is the maximum switch voltage minus a diode drop. In a
flyback regulator, the maximum output voltage is determined by the turns ratio, N, and the duty cycle, D, by the
equation:
VOUT ≈ N × VIN × D/(1 − D)
(4)
The duty cycle of a flyback regulator is determined by the following equation:
(5)
Theoretically, the maximum output voltage can be as large as desired—just keep increasing the turns ratio of the
transformer. However, there exists some physical limitations that prevent the turns ratio, and thus the output
voltage, from increasing to infinity. The physical limitations are capacitances and inductances in the LM2588
switch, the output diode(s), and the transformer—such as reverse recovery time of the output diode (mentioned
above).
28
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
NOISY INPUT LINE CONDITION
A small, low-pass RC filter should be used at the input pin of the LM2588 if the input voltage has an unusually
large amount of transient noise, such as with an input switch that bounces. The circuit in Figure 59 demonstrates
the layout of the filter, with the capacitor placed from the input pin to ground and the resistor placed between the
input supply and the input pin. Note that the values of RIN and CIN shown in the schematic are good enough for
most applications, but some readjusting might be required for a particular application. If efficiency is a major
concern, replace the resistor with a small inductor (say 10 μH and rated at 200 mA).
STABILITY
All current-mode controlled regulators can suffer from an instability, known as subharmonic oscillation, if they
operate with a duty cycle above 50%. To eliminate subharmonic oscillations, a minimum value of inductance is
required to ensure stability for all boost and flyback regulators. The minimum inductance is given by:
(6)
where VSAT is the switch saturation voltage and can be found in the Characteristic Curves.
Figure 60. Circuit Board Layout
CIRCUIT LAYOUT GUIDELINES
As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring
inductance generate voltage transients which can cause problems. For minimal inductance and ground loops,
keep the length of the leads and traces as short as possible. Use single point grounding or ground plane
construction for best results. Separate the signal grounds from the power grounds (as indicated in Figure 60).
When using the Adjustable version, physically locate the programming resistors as near the regulator IC as
possible, to keep the sensitive feedback wiring short.
HEAT SINK/THERMAL CONSIDERATIONS
In many cases, a heat sink is not required to keep the LM2588 junction temperature within the allowed operating
temperature range. For each application, to determine whether or not a heat sink will be required, the following
must be identified:
1) Maximum ambient temperature (in the application).
2) Maximum regulator power dissipation (in the application).
3) Maximum allowed junction temperature (125°C for the LM2588). For a safe, conservative design, a
temperature approximately 15°C cooler than the maximum junction temperature should be selected (110°C).
4) LM2588 package thermal resistances θJA and θJC (given in the Electrical Characteristics).
Total power dissipated (PD) by the LM2588 can be estimated as follows:
Boost:
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
29
LM2588
SNVS117D – APRIL 1998 – REVISED APRIL 2013
www.ti.com
(7)
VIN is the minimum input voltage, VOUT is the output voltage, N is the transformer turns ratio, D is the duty cycle,
and ILOAD is the maximum load current (and ∑ILOAD is the sum of the maximum load currents for multiple-output
flyback regulators). The duty cycle is given by:
Boost:
(8)
where VF is the forward biased voltage of the diode and is typically 0.5V for Schottky diodes and 0.8V for fast
recovery diodes. VSAT is the switch saturation voltage and can be found in the Characteristic Curves.
When no heat sink is used, the junction temperature rise is:
ΔTJ = PD • θJA.
(9)
Adding the junction temperature rise to the maximum ambient temperature gives the actual operating junction
temperature:
TJ = ΔTJ + TA.
(10)
If the operating junction temperature exceeds the maximum junction temperatue in item 3 above, then a heat
sink is required. When using a heat sink, the junction temperature rise can be determined by the following:
ΔTJ = PD • (θJC + θInterface + θHeat Sink)
(11)
Again, the operating junction temperature will be:
TJ = ΔTJ + TA
(12)
As before, if the maximum junction temperature is exceeded, a larger heat sink is required (one that has a lower
thermal resistance).
Included in the Switchers Made Simple™ design software is a more precise (non-linear) thermal model that can
be used to determine junction temperature with different input-output parameters or different component values.
It can also calculate the heat sink thermal resistance required to maintain the regulator junction temperature
below the maximum operating temperature.
To further simplify the flyback regulator design procedure, Texas Instruments is making available computer
design software Switchers Made Simple™. Software is available on a (3½″) diskette for IBM compatible
computers from a Texas Instruments sales office in your area or the Texas Instruments Customer Response
Center (1-800-272-9959).
30
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
LM2588
www.ti.com
SNVS117D – APRIL 1998 – REVISED APRIL 2013
REVISION HISTORY
Changes from Revision C (April 2013) to Revision D
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 30
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2588
31
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2588S-12/NOPB
ACTIVE
DDPAK/
TO-263
KTW
7
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2588S
-12 P+
LM2588S-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTW
7
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2588S
-3.3 P+
LM2588S-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTW
7
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2588S
-5.0 P+
LM2588S-ADJ
NRND
DDPAK/
TO-263
KTW
7
45
TBD
Call TI
Call TI
-40 to 125
LM2588S
-ADJ P+
LM2588S-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTW
7
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2588S
-ADJ P+
LM2588SX-12/NOPB
ACTIVE
DDPAK/
TO-263
KTW
7
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2588S
-12 P+
LM2588SX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTW
7
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2588S
-3.3 P+
LM2588SX-5.0
NRND
DDPAK/
TO-263
KTW
7
500
TBD
Call TI
Call TI
-40 to 125
LM2588S
-5.0 P+
LM2588SX-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTW
7
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2588S
-5.0 P+
LM2588SX-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTW
7
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2588S
-ADJ P+
LM2588T-3.3/NOPB
ACTIVE
TO-220
NDZ
7
45
Pb-Free (RoHS
Exempt)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2588T
-3.3 P+
LM2588T-5.0
NRND
TO-220
NDZ
7
45
TBD
Call TI
Call TI
-40 to 125
LM2588T
-5.0 P+
LM2588T-5.0/NOPB
ACTIVE
TO-220
NDZ
7
45
Pb-Free (RoHS
Exempt)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2588T
-5.0 P+
LM2588T-ADJ
NRND
TO-220
NDZ
7
45
TBD
Call TI
Call TI
-40 to 125
LM2588T
-ADJ P+
LM2588T-ADJ/NOPB
ACTIVE
TO-220
NDZ
7
45
Pb-Free (RoHS
Exempt)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2588T
-ADJ P+
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM2588SX-12/NOPB
DDPAK/
TO-263
KTW
7
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM2588SX-3.3/NOPB
DDPAK/
TO-263
KTW
7
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM2588SX-5.0
DDPAK/
TO-263
KTW
7
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM2588SX-5.0/NOPB
DDPAK/
TO-263
KTW
7
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM2588SX-ADJ/NOPB
DDPAK/
TO-263
KTW
7
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM2588SX-12/NOPB
DDPAK/TO-263
KTW
7
500
367.0
367.0
45.0
LM2588SX-3.3/NOPB
DDPAK/TO-263
KTW
7
500
367.0
367.0
45.0
LM2588SX-5.0
DDPAK/TO-263
KTW
7
500
367.0
367.0
45.0
LM2588SX-5.0/NOPB
DDPAK/TO-263
KTW
7
500
367.0
367.0
45.0
LM2588SX-ADJ/NOPB
DDPAK/TO-263
KTW
7
500
367.0
367.0
45.0
Pack Materials-Page 2
MECHANICAL DATA
NDZ0007B
TA07B (Rev E)
www.ti.com
MECHANICAL DATA
KTW0007B
TS7B (Rev E)
BOTTOM SIDE OF PACKAGE
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated