TI LM5111

LM5111
www.ti.com
SNVS300F – JULY 2004 – REVISED MAY 2011
LM5111 Dual 5A Compound Gate Driver
Check for Samples: LM5111
FEATURES
DESCRIPTION
•
The LM5111 Dual Gate Driver replaces industry
standard gate drivers with improved peak output
current and efficiency. Each “compound” output driver
stage includes MOS and bipolar transistors operating
in parallel that together sink more than 5A peak from
capacitive
loads.
Combining
the
unique
characteristics of MOS and bipolar devices reduces
drive current variation with voltage and temperature.
Under-voltage lockout protection is also provided.
The drivers can be operated in parallel with inputs
and outputs connected to double the drive current
capability. This device is available in the SOIC
package or the thermally enhanced VSSOP package.
1
2
•
•
•
•
•
•
•
•
•
•
Independently Drives Two N-Channel
MOSFETs
Compound CMOS and Bipolar Outputs Reduce
Output Current Variation
5A Sink/3A Source Current Capability
Two Channels can be Connected in Parallel to
Double the Drive Current
Independent Inputs (TTL Compatible)
Fast Propagation Times (25 ns Typical)
Fast Rise and Fall Times (14 ns/12 ns Rise/Fall
with 2 nF Load)
Available in Dual Non-Inverting, Dual Inverting
and Combination Configurations
Supply Rail Under-Voltage Lockout Protection
(UVLO)
LM5111-4 UVLO Configured to Drive PFET
through OUT_A and NFET through OUT_B
Pin Compatible with Industry Standard Gate
Drivers
TYPICAL APPLICATIONS
•
•
•
Synchronous Rectifier Gate Drivers
Switch-mode Power Supply Gate Driver
Solenoid and Motor Drivers
PACKAGES
•
•
SOIC
Thermally Enhanced VSSOP
CONNECTION DIAGRAM
NC
IN_A
VEE
IN_B
1
8
2
7
3
6
4
5
NC
OUT A
VCC
OUT_B
Figure 1. 8-Lead SOIC or VSSOP
See D or DGN0008A Package
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2011, Texas Instruments Incorporated
LM5111
SNVS300F – JULY 2004 – REVISED MAY 2011
www.ti.com
PIN DESCRIPTIONS
Pin
Name
Description
Application Information
1
NC
No Connect
2
IN_A
‘A’ side control input
TTL compatible thresholds.
3
VEE
Ground reference for both inputs and
outputs
Connect to power ground.
4
IN_B
‘B’ side control input
TTL compatible thresholds.
5
OUT_B
Output for the ‘B’ side driver.
Voltage swing of this output is from VCC to VEE. The output
stage is capable of sourcing 3A and sinking 5A.
6
VCC
Positive output supply
Locally decouple to VEE.
7
OUT_A.
Output for the ‘A’ side driver.
Voltage swing of this output is from VCC to VEE. The output
stage is capable of sourcing 3A and sinking 5A.
8
NC
No Connect
EP (VSSOP Package)
It is recommended that the exposed pad on the bottom of the
package be soldered to ground plane on the PC board to aid
thermal dissipation.
Configuration Table
Part Number
“A” Output Configuration
“B” Output Configuration
Package
LM5111-1M/-1MX/-1MY/-1MYX
Non-Inverting (Low in UVLO)
Non-Inverting (Low in UVLO)
SOIC, VSSOP
LM5111-2M/-2MX/-2MY/-2MYX
Inverting (Low in UVLO)
Inverting (Low in UVLO)
SOIC, VSSOP
LM5111-3M/-3MX/-3MY/-3MYX
Inverting (Low in UVLO)
Non-Inverting (Low in UVLO)
SOIC, VSSOP
LM5111-4M/-4MX/-4MY/-4MYX
Inverting (High in UVLO)
Non-Inverting (Low in UVLO)
SOIC, VSSOP
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2)
−0.3V to 15V
VCC to VEE
−0.3V to 15V
IN to VEE
−55°C to +150°C
Storage Temperature Range, (TSTG)
Maximum Junction Temperature, (TJ(max))
+150°C
Operating Junction Temperature
+125°C
ESD Rating
(1)
(2)
2
2kV
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
LM5111
www.ti.com
SNVS300F – JULY 2004 – REVISED MAY 2011
Electrical Characteristics
TJ = −40°C to +125°C, VCC = 12V, VEE = 0V, No Load on OUT_A or OUT_B, unless otherwise specified.
Symbol
Parameter
Conditions
Min
VCC−VEE
3.5
VCCR
VCC Under Voltage Lockout (rising) VCC−VEE
2.3
VCCH
VCC Under Voltage Lockout
Hysteresis
VCC Operating Range
ICC
VCC Supply Current (ICC)
Typ
Max
Units
14
V
2.9
3.5
V
230
mV
IN_A = IN_B = 0V (5111-1)
1
2
IN_A = IN_B = VCC (5111-2)
1
2
IN_A = VCC, IN_B = 0V (5111-3)
1
2
mA
CONTROL INPUTS
VIH
Logic High
VIL
Logic Low
VthH
High Threshold
1.3
VthL
Low Threshold
0.8
HYS
Input Hysteresis
IIL
Input Current Low
IIH
Input Current High
2.2
V
0.8
V
1.75
2.2
V
1.35
2.0
V
400
IN_A=IN_B=VCC (5111-1-2-3)
−1
mV
0.1
1
25
IN_B=VCC (5111-3)
10
18
IN_A=IN_B=VCC (5111-2)
−1
0.1
1
IN_A=IN_B=VCC (5111-1)
10
18
25
IN_A=VCC (5111-3)
-1
0.1
1
µA
OUTPUT DRIVERS
ROH
Output Resistance High
IOUT = −10 mA (1)
30
50
Ω
ROL
Output Resistance Low
IOUT = + 10 mA (1)
1.4
2.5
Ω
ISource
Peak Source Current
OUTA/OUTB = VCC/2,
200 ns Pulsed Current
3
A
ISink
Peak Sink Current
OUTA/OUTB = VCC/2,
200 ns Pulsed Current
5
A
SWITCHING CHARACTERISTICS
td1
Propagation Delay Time Low to
High, IN rising (IN to OUT)
CLOAD = 2 nF
See Figure 2 and Figure 3
25
40
ns
td2
Propagation Delay Time High to
Low, IN falling (IN to OUT)
CLOAD = 2 nF
See Figure 2 and Figure 3
25
40
ns
tr
Rise Time
CLOAD = 2 nF
See Figure 2 and Figure 3
14
25
ns
tf
Fall Time
CLOAD = 2 nF
See Figure 2 and Figure 3
12
25
ns
TJ = 150°C
500
mA
LATCHUP PROTECTION
AEC - Q100, Method 004
THERMAL RESISTANCE
θJA
Junction to Ambient,
0 LFPM Air Flow
SOIC Package
VSSOP Package
170
60
°C/W
θJC
Junction to Case
SOIC Package
VSSOP Package
70
4.7
°C/W
(1)
The output resistance specification applies to the MOS device only. The total output current capability is the sum of the MOS and
Bipolar devices.
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
3
LM5111
SNVS300F – JULY 2004 – REVISED MAY 2011
www.ti.com
Timing Waveforms
INPUT
INPUT
OUTPUT
50%
50%
50%
50%
tD1
tD2
tD1
tD2
90%
90%
OUTPUT
10%
10%
tf
tr
tr
Figure 2. Inverting
4
tf
Figure 3. Non-Inverting
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
LM5111
www.ti.com
SNVS300F – JULY 2004 – REVISED MAY 2011
Typical Performance Characteristics
Supply Current vs Frequency
Supply Current vs Capacitive Load
1000
100
TA = 25°C
10
VCC = 12V
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
VCC = 15V
VCC = 10V
VCC = 5V
1
f = 500kHz
100
10
f = 100kHz
1
TA = 25°C
f = 10kHz
CL = 2200pF
0.1
100
0.1
1
10
100
1000
10k
1k
CAPACITIVE LOAD (pF)
FREQUENCY (kHz)
Figure 4.
Figure 5.
Rise and Fall Time vs Supply Voltage
Rise and Fall Time vs Temperature
20
20
TA = 25°C
VCC = 12V
CL = 2200pF
CL = 2200pF
18
18
16
16
TIME (ns)
TIME (ns)
tr
tr
14
14
tf
tf
12
12
10
10
5 6
4
7
8
9 10 11 12 13 14 15 16
-75 -50 -25 0
25 50 75 100 125 150 175
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
Figure 6.
Figure 7.
Rise and Fall Time vs Capacitive Load
Delay Time vs Supply Voltage
32.5
50
TA = 25°C
TA = 25°C
VCC = 12V
CL = 2200pF
30
40
tr
20
tD2
TIME (ns)
TIME (ns)
27.5
30
tf
25
22.5
tD1
10
20
17.5
0
100
1k
CAPACITIVE LOAD (pF)
10k
4
6
8
10
12
14
16
SUPPLY VOLTAGE (V)
Figure 8.
Figure 9.
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
5
LM5111
SNVS300F – JULY 2004 – REVISED MAY 2011
www.ti.com
Typical Performance Characteristics (continued)
Delay Time vs Temperature
RDSON vs Supply Voltage
32.5
3.25
VCC = 12V
CL = 2200pF
IOUT = 10mA
2.75
tD2
ROH
ROL (:)
TIME (ns)
27.5
55
25
tD1
45
2.25
1.75
35
22.5
ROH (:)
30
65
TA = 25°C
ROL
1.25
20
17.5
25
15
0.75
-75 -50 -25 0
0
25 50 75 100 125 150 175
TEMPERATURE (°C)
3
6
9
12
15
18
SUPPLY VOLTAGE (V)
Figure 10.
Figure 11.
UVLO Thresholds and Hysteresis vs Temperature
0.450
VCCR
2.800
2.500
VCCF
0.390
0.330
2.200
0.270
VCCH
1.900
1.600
-75 -50 -25 0
HYSTERESIS (V)
UVLO THRESHOLDS (V)
3.100
0.210
0.150
25 50 75 100 125 150 175
TEMPERATURE (°C)
Figure 12.
6
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
LM5111
www.ti.com
SNVS300F – JULY 2004 – REVISED MAY 2011
Block Diagram
VCC
UVLO
VEE
OUT_A
IN_A
VEE
VCC
IN_B
OUT_B
VEE
Figure 13. Block Diagram of LM5111
Detailed Operating Description
LM5111 dual gate driver consists of two independent and identical driver channels with TTL compatible logic
inputs and high current totem-pole outputs that source or sink current to drive MOSFET gates. The driver output
consist of a compound structure with MOS and bipolar transistor operating in parallel to optimize current
capability over a wide output voltage and operating temperature range. The bipolar device provides high peak
current at the critical threshold region of the MOSFET VGS while the MOS devices provide rail-to-rail output
swing. The totem pole output drives the MOSFET gate between the gate drive supply voltage VCC and the power
ground potential at the VEE pin.
The control inputs of the drivers are high impedance CMOS buffers with TTL compatible threshold voltages. The
LM5111 pinout was designed for compatibility with industry standard gate drivers in single supply gate driver
applications.
The input stage of each driver should be driven by a signal with a short rise and fall time. Slow rising and falling
input signals, although not harmful to the driver, may result in the output switching repeatedly at a high
frequency.
The two driver channels of the LM5111 are designed as identical cells. Transistor matching inherent to integrated
circuit manufacturing ensures that the AC and DC peformance of the channels are nearly identical. Closely
matched propagation delays allow the dual driver to be operated as a single with inputs and output pins
connected. The drive current capability in parallel operation is precisely 2X the drive of an individual channel.
Small differences in switching speed between the driver channels will produce a transient current (shoot-through)
in the output stage when two output pins are connected to drive a single load. Differences in input thresholds
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
7
LM5111
SNVS300F – JULY 2004 – REVISED MAY 2011
www.ti.com
between the driver channels will also produce a transient current (shoot-through) in the output stage. Fast
transition input signals are especially important while operating in a parallel configuration. The efficiency loss for
parallel operation has been characterized at various loads, supply voltages and operating frequencies. The
power dissipation in the LM5111 increases be less than 1% relative to the dual driver configuration when
operated as a single driver with inputs/ outputs connected.
An Under Voltage Lock Out (UVLO) circuit is included in the LM5111, which senses the voltage difference
between VCC and the chip ground pin, VEE. When the VCC to VEE voltage difference falls below 2.8V both driver
channels are disabled. The UVLO hysteresis prevents chattering during brown-out conditions and the driver will
resume normal operation when the VCC to VEE differential voltage exceeds approximately 3.0V.
The LM5111-1, -2 and -3 devices hold both outputs in the low state in the under-voltage lockout (UVLO)
condition. The LM5111-4 is distinguished from the LM5111-3 by the active high output state of OUT_A during
UVLO. When VCC is less than the UVLO threshold voltage, OUT_A of the LM5111-4 will be locked in the high
state while OUT_B will be disabled in the low state. This configuration allows the LM5111-4 to drive a PFET
through OUT_A and an NFET through OUT_B with both FETs safely turned off during UVLO.
The LM5111 is available in dual non-inverting (-1), dual Inverting (-2) and the combination inverting plus noninverting (-3, -4) configurations. All configurations are offered in the SOIC and VSSOP plastic packages.
Layout Considerations
Attention must be given to board layout when using LM5111. Some important considerations include:
1. A Low ESR/ESL capacitor must be connected close to the IC and between the VCC and VEE pins to support
high peak currents being drawn from VCC during turn-on of the MOSFET.
2. Proper grounding is crucial. The drivers need a very low impedance path for current return to ground
avoiding inductive loops. The two paths for returning current to ground are a) between LM5111 VEE pin and
the ground of the circuit that controls the driver inputs, b) between LM5111 VEE pin and the source of the
power MOSFET being driven. All these paths should be as short as possible to reduce inductance and be as
wide as possible to reduce resistance. All these ground paths should be kept distinctly separate to avoid
coupling between the high current output paths and the logic signals that drive the LM5111. A good method
is to dedicate one copper plane in a multi-layered PCB to provide a common ground surface.
3. With the rise and fall times in the range of 10 ns to 30 ns, care is required to minimize the lengths of current
carrying conductors to reduce their inductance and EMI from the high di/dt transients generated by the
LM5111.
4. The LM5111 footprint is compatible with other industry standard drivers including the TC4426/27/28 and
UCC27323/4/5.
5. If either channel is not being used, the respective input pin (IN_A or IN_B) should be connected to either VEE
or VCC to avoid spurious output signals.
8
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
LM5111
www.ti.com
SNVS300F – JULY 2004 – REVISED MAY 2011
Thermal Performance
INTRODUCTION
The primary goal of thermal management is to maintain the integrated circuit (IC) junction temperature (TJ) below
a specified maximum operating temperature to ensure reliability. It is essential to estimate the maximum TJ of IC
components in worst case operating conditions. The junction temperature is estimated based on the power
dissipated in the IC and the junction to ambient thermal resistance θJA for the IC package in the application board
and environment. The θJA is not a given constant for the package and depends on the printed circuit board
design and the operating environment.
DRIVE POWER REQUIREMENT CALCULATIONS IN LM5111
The LM5111 dual low side MOSFET driver is capable of sourcing/sinking 3A/5A peak currents for short intervals
to drive a MOSFET without exceeding package power dissipation limits. High peak currents are required to
switch the MOSFET gate very quickly for operation at high frequencies.
VGATE
VHIGH
Q1
RG
VTRIG
CIN
Q2
The schematic above shows a conceptual diagram of the LM5111 output and MOSFET load. Q1 and Q2 are the
switches within the gate driver. RG is the gate resistance of the external MOSFET, and CIN is the equivalent gate
capacitance of the MOSFET. The gate resistance Rg is usually very small and losses in it can be neglected. The
equivalent gate capacitance is a difficult parameter to measure since it is the combination of CGS (gate to source
capacitance) and CGD (gate to drain capacitance). Both of these MOSFET capacitances are not constants and
vary with the gate and drain voltage. The better way of quantifying gate capacitance is the total gate charge QG
in coloumbs. QG combines the charge required by CGS and CGD for a given gate drive voltage VGATE.
Assuming negligible gate resistance, the total power dissipated in the MOSFET driver due to gate charge is
approximated by
PDRIVER = VGATE x QG x FSW
where
•
FSW = switching frequency of the MOSFET
(1)
For example, consider the MOSFET MTD6N15 whose gate charge specified as 30 nC for VGATE = 12V.
The power dissipation in the driver due to charging and discharging of MOSFET gate capacitances at switching
frequency of 300 kHz and VGATE of 12V is equal to
PDRIVER = 12V x 30 nC x 300 kHz = 0.108W.
(2)
If both channels of the LM5111 are operating at equal frequency with equivalent loads, the total losses will be
twice as this value which is 0.216W.
In addition to the above gate charge power dissipation, - transient power is dissipated in the driver during output
transitions. When either output of the LM5111 changes state, current will flow from VCC to VEE for a very brief
interval of time through the output totem-pole N and P channel MOSFETs. The final component of power
dissipation in the driver is the power associated with the quiescent bias current consumed by the driver input
stage and Under-voltage lockout sections.
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
9
LM5111
SNVS300F – JULY 2004 – REVISED MAY 2011
www.ti.com
Characterization of the LM5111 provides accurate estimates of the transient and quiescent power dissipation
components. At 300 kHz switching frequency and 30 nC load used in the example, the transient power will be 8
mW. The 1 mA nominal quiescent current and 12V VGATE supply produce a 12 mW typical quiescent power.
Therefore the total power dissipation
PD = 0.216 + 0.008 + 0.012 = 0.236W.
(3)
We know that the junction temperature is given by
TJ = PD x θJA + TA
(4)
Or the rise in temperature is given by
TRISE = TJ − TA = PD x θJA
(5)
For SOIC package, θJA is estimated as 170°C/W for the conditions of natural convection. For VSSOP, θJA is
typically 60°C/W.
Therefore for SOIC TRISE is equal to
TRISE = 0.236 x 170 = 40.1°C
(6)
CONTINUOUS CURRENT RATING OF LM5111
The LM5111 can deliver pulsed source/sink currents of 3A and 5A to capacitive loads. In applications requiring
continuous load current (resistive or inductive loads), package power dissipation, limits the LM5111 current
capability far below the 5A sink/3A source capability. Rated continuous current can be estimated both when
sourcing current to or sinking current from the load. For example when sinking, the maximum sink current can be
calculated as:
ISINK (MAX) :=
TJ(MAX) - TA
TJA · RDS (ON)
where
•
RDS(on) is the on resistance of lower MOSFET in the output stage of LM5111
(7)
Consider TJ(max) of 125°C and θJA of 170°C/W for an SO-8 package under the condition of natural convection
and no air flow. If the ambient temperature (TA) is 60°C, and the RDS(on) of the LM5111 output at TJ(max) is
2.5Ω, this equation yields ISINK(max) of 391mA which is much smaller than 5A peak pulsed currents.
Similarly, the maximum continuous source current can be calculated as
TJ(MAX) - TA
ISOURCE (MAX) :=
TJA · VDIODE
where
•
VDIODE is the voltage drop across hybrid output stage which varies over temperature and can be assumed to
be about 1.1V at TJ(max) of 125°C
(8)
Assuming the same parameters as above, this equation yields ISOURCE(max) of 347mA.
10
Submit Documentation Feedback
Copyright © 2004–2011, Texas Instruments Incorporated
Product Folder Links: LM5111
PACKAGE OPTION ADDENDUM
www.ti.com
9-Mar-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LM5111-1M
ACTIVE
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 125
5111
-1M
LM5111-1M/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
5111
-1M
LM5111-1MX
ACTIVE
SOIC
D
8
2500
TBD
Call TI
Call TI
-40 to 125
5111
-1M
LM5111-1MX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
5111
-1M
LM5111-1MY
ACTIVE
MSOPPowerPAD
DGN
8
1000
TBD
Call TI
Call TI
SJKB
LM5111-1MY/NOPB
ACTIVE
MSOPPowerPAD
DGN
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
SJKB
LM5111-1MYX
ACTIVE
MSOPPowerPAD
DGN
8
3500
TBD
Call TI
Call TI
SJKB
LM5111-1MYX/NOPB
ACTIVE
MSOPPowerPAD
DGN
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
SJKB
LM5111-2M
ACTIVE
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 125
5111
-2M
LM5111-2M/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
5111
-2M
LM5111-2MX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
5111
-2M
LM5111-2MY
ACTIVE
MSOPPowerPAD
DGN
8
1000
TBD
Call TI
Call TI
SJLB
LM5111-2MY/NOPB
ACTIVE
MSOPPowerPAD
DGN
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
SJLB
LM5111-2MYX
ACTIVE
MSOPPowerPAD
DGN
8
3500
TBD
Call TI
Call TI
SJLB
LM5111-2MYX/NOPB
ACTIVE
MSOPPowerPAD
DGN
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
SJLB
LM5111-3M
ACTIVE
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 125
5111
-3M
LM5111-3M/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
5111
-3M
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
9-Mar-2013
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LM5111-3MX
ACTIVE
SOIC
D
8
2500
TBD
Call TI
Call TI
-40 to 125
5111
-3M
LM5111-3MX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
5111
-3M
LM5111-3MY
ACTIVE
MSOPPowerPAD
DGN
8
1000
TBD
Call TI
Call TI
SJNB
LM5111-3MY/NOPB
ACTIVE
MSOPPowerPAD
DGN
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
SJNB
LM5111-3MYX
ACTIVE
MSOPPowerPAD
DGN
8
3500
TBD
Call TI
Call TI
SJNB
LM5111-3MYX/NOPB
ACTIVE
MSOPPowerPAD
DGN
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
SJNB
LM5111-4M/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
5111
-4M
LM5111-4MX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
5111
-4M
LM5111-4MY/NOPB
ACTIVE
MSOPPowerPAD
DGN
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
SSYB
LM5111-4MYX/NOPB
ACTIVE
MSOPPowerPAD
DGN
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
SSYB
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
9-Mar-2013
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Nov-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LM5111-1MX
Package Package Pins
Type Drawing
SOIC
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM5111-1MX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM5111-1MY
MSOPPower
PAD
DGN
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-1MY/NOPB
MSOPPower
PAD
DGN
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-1MYX
MSOPPower
PAD
DGN
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-1MYX/NOPB
MSOPPower
PAD
DGN
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-2MX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM5111-2MY
MSOPPower
PAD
DGN
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-2MY/NOPB
MSOPPower
PAD
DGN
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-2MYX
MSOP-
DGN
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Nov-2012
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
Power
PAD
LM5111-2MYX/NOPB
MSOPPower
PAD
DGN
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-3MX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM5111-3MX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM5111-3MY
MSOPPower
PAD
DGN
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-3MY/NOPB
MSOPPower
PAD
DGN
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-3MYX
MSOPPower
PAD
DGN
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-3MYX/NOPB
MSOPPower
PAD
DGN
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-4MX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM5111-4MY/NOPB
MSOPPower
PAD
DGN
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5111-4MYX/NOPB
MSOPPower
PAD
DGN
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Nov-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM5111-1MX
SOIC
D
8
2500
349.0
337.0
45.0
LM5111-1MX/NOPB
SOIC
D
8
2500
349.0
337.0
45.0
LM5111-1MY
MSOP-PowerPAD
DGN
8
1000
203.0
190.0
41.0
LM5111-1MY/NOPB
MSOP-PowerPAD
DGN
8
1000
203.0
190.0
41.0
LM5111-1MYX
MSOP-PowerPAD
DGN
8
3500
349.0
337.0
45.0
LM5111-1MYX/NOPB
MSOP-PowerPAD
DGN
8
3500
349.0
337.0
45.0
LM5111-2MX/NOPB
SOIC
D
8
2500
349.0
337.0
45.0
LM5111-2MY
MSOP-PowerPAD
DGN
8
1000
203.0
190.0
41.0
LM5111-2MY/NOPB
MSOP-PowerPAD
DGN
8
1000
203.0
190.0
41.0
LM5111-2MYX
MSOP-PowerPAD
DGN
8
3500
349.0
337.0
45.0
LM5111-2MYX/NOPB
MSOP-PowerPAD
DGN
8
3500
349.0
337.0
45.0
LM5111-3MX
SOIC
D
8
2500
349.0
337.0
45.0
LM5111-3MX/NOPB
SOIC
D
8
2500
349.0
337.0
45.0
LM5111-3MY
MSOP-PowerPAD
DGN
8
1000
203.0
190.0
41.0
LM5111-3MY/NOPB
MSOP-PowerPAD
DGN
8
1000
203.0
190.0
41.0
LM5111-3MYX
MSOP-PowerPAD
DGN
8
3500
349.0
337.0
45.0
LM5111-3MYX/NOPB
MSOP-PowerPAD
DGN
8
3500
349.0
337.0
45.0
LM5111-4MX/NOPB
SOIC
D
8
2500
349.0
337.0
45.0
LM5111-4MY/NOPB
MSOP-PowerPAD
DGN
8
1000
203.0
190.0
41.0
LM5111-4MYX/NOPB
MSOP-PowerPAD
DGN
8
3500
349.0
337.0
45.0
Pack Materials-Page 3
MECHANICAL DATA
DGN0008A
MUY08A (Rev A)
BOTTOM VIEW
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated