LM6142 Dual and LM6144 Quad High Speed/Low Power 17 MHz Rail-to-Rail Input-Output Operational Amplifiers General Description Features Using patent pending new circuit topologies, the LM6142/44 provides new levels of performance in applications where low voltage supplies or power limitations previously made compromise necessary. Operating on supplies of 1.8V to over 24V, the LM6142/44 is an excellent choice for battery operated systems, portable instrumentation and others. The greater than rail-to-rail input voltage range eliminates concern over exceeding the common-mode voltage range. The rail-to-rail output swing provides the maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. High gain-bandwidth with 650 µA/Amplifier supply current opens new battery powered applications where previous higher power consumption reduced battery life to unacceptable levels. The ability to drive large capacitive loads without oscillating functionally removes this common problem. At VS = 5V. Typ unless noted. n Rail-to-rail input CMVR −0.25V to 5.25V n Rail-to-rail output swing 0.005V to 4.995V n Wide gain-bandwidth: 17 MHz at 50 kHz (typ) n Slew rate: Small signal, 5V/µs Large signal, 30V/µs n Low supply current 650 µA/Amplifier n Wide supply range 1.8V to 24V n CMRR 107 dB n Gain 108 dB with RL = 10k n PSRR 87 dB Applications n n n n n Battery operated instrumentation Depth sounders/fish finders Barcode scanners Wireless communications Rail-to-rail in-out instrumentation amps Connection Diagrams 8-Pin CDIP 8-Pin DIP/SO DS012057-14 Top View © 1999 National Semiconductor Corporation DS012057-1 Top View DS012057 www.national.com LM6142 Dual and LM6144 Quad High Speed/Low Power 17 MHz Rail-to-Rail Input-Output Operational Amplifiers May 1999 Connection Diagrams (Continued) 14-Pin DIP/SO DS012057-2 Top View Ordering Information Package Temperature Range Temperature Range Industrial Military −40˚C to +85˚C −55˚C to +125˚C NSC Drawing 8-Pin Molded DIP LM6142AIN, LM6142BIN N08E 8-Pin Small Outline LM6142AIM, LM6142BIM M08A 14-Pin Molded DIP LM6144AIN, LM6144BIN N14A 14-Pin Small Outline LM6144AIM, LM6144BIM M14A 8-Pin CDIP www.national.com LM6142AMJ-QML 2 J08A Absolute Maximum Ratings (Note 1) Storage Temp. Range Junction Temperature (Note 4) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Differential Input Voltage Voltage at Input/Output Pin Supply Voltage (V+ − V−) Current at Input Pin Current at Output Pin (Note 3) Current at Power Supply Pin Lead Temperature (soldering, 10 sec) −65˚C to +150˚C 150˚C Operating Ratings (Note 1) 2500V 15V (V+) + 0.3V, (V−) − 0.3V 35V ± 10 mA ± 25 mA 50 mA Supply Voltage Junction Temperature Range LM6142, LM6144 Thermal Resistance (θJA) N Package, 8-Pin Molded DIP M Package, 8-Pin Surface Mount N Package, 14-Pin Molded DIP M Package, 14-Pin Surface Mount 1.8V ≤ V+ ≤ 24V −40˚C ≤ TJ ≤ +85˚C 115˚C/W 193˚C/W 81˚C/W 126˚C/W 260˚C 5.0V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C, V+ = 5.0V, V− = 0V, VCM = VO = V+/2 and RL > 1 MΩ to V+/2. Boldface limits apply at the temperature extremes. Symbol VOS TCVOS Parameter Conditions Input Offset Voltage LM6144AI LM6144BI Typ LM6142AI LM6142BI (Note 5) Limit Limit (Note 6) (Note 6) 1.0 2.5 mV 2.2 3.3 max 0.3 Input Offset Voltage 3 Units µV/˚C Average Drift IB Input Bias Current 0V ≤ VCM ≤ 5V 170 250 180 280 526 IOS Input Offset Current RIN Input Resistance, CM CMRR Common Mode 3 Power Supply AV nA 80 max 84 MΩ 84 78 78 0V ≤ VCM ≤ 5V 82 66 66 79 64 64 87 80 80 78 78 dB min Input Common-Mode −0.25 0 0 Voltage Range 5.25 5.0 5.0 270 100 80 V/mV 70 33 25 min 0.005 0.01 0.01 V 0.013 0.013 max Large Signal RL = 10k Voltage Gain VO 30 80 107 Rejection Ratio VCM 526 126 5V ≤ V+ ≤ 24V nA max 30 0V ≤ VCM ≤ 4V Rejection Ratio PSRR 300 Output Swing RL = 100k 4.995 RL = 10k 4.98 4.98 V 4.93 4.93 min 0.02 V max 4.97 RL = 2k 0.06 4.90 3 V V min 0.1 0.1 V 0.133 0.133 max 4.86 4.86 V 4.80 4.80 min www.national.com 5.0V DC Electrical Characteristics (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25˚C, V+ = 5.0V, V− = 0V, VCM = VO = V+/2 and RL > 1 MΩ to V+/2. Boldface limits apply at the temperature extremes. LM6144AI LM6144BI Typ LM6142AI LM6142BI (Note 5) Limit Limit (Note 6) (Note 6) 10 8 mA Circuit Current 4.9 4 min LM6142 35 35 Symbol Parameter Output Short ISC Conditions Sourcing 13 Units mA max Sinking 24 10 10 mA 5.3 5.3 min 35 35 mA max ISC Output Short 6 6 mA Circuit Current Sourcing 8 3 3 min LM6144 35 35 mA max Sinking 22 8 8 mA 4 4 min 35 35 mA max IS Supply Current Per Amplifier 650 800 800 µA 880 880 max 5.0V AC Electrical Characteristics Unless Otherwise Specified, All Limits Guaranteed for TJ = 25˚C, V+ = 5.0V, V− = 0V, VCM = VO = V+/2 and RL > 1 MΩ to VS/2. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Slew Rate 8 Vp-p @ VCC 12V GBW Gain-Bandwidth Product RS > 1 kΩ f = 50 kHz φm Phase Margin SR Input-Referred LM6144BI LM6142AI LM6142BI (Note 5) Limit Limit (Note 6) (Note 6) 25 17 Amp-to-Amp Isolation en LM6144AI Typ Units 15 13 13 11 V/µs min 10 10 MHz 6 6 min 38 Deg 130 dB f = 1 kHz 16 f = 1 kHz 0.22 f = 10 kHz, RL = 10 kΩ, 0.003 Voltage Noise in Input-Referred Current Noise T.H.D. Total Harmonic Distortion www.national.com 4 % 2.7V DC Electrical Characteristics Unless Otherwise Specified, All Limits Guaranteed for TJ = 25˚C, V+ = 2.7V, V− = 0V, VCM = VO = V+/2 and RL > 1 MΩ to V+/2. Boldface limits apply at the temperature extreme Symbol VOS IB IOS Parameter Conditions Input Offset Voltage LM6144AI LM6144BI Typ LM6142AI LM6142BI (Note 5) Limit Limit (Note 6) (Note 6) 1.8 2.5 mV 4.3 4.3 max 250 300 nA 526 526 max 30 30 nA 80 80 max 0.4 Input Bias Current 150 Input Offset Current 4 Units RIN Input Resistance 128 MΩ CMRR Common Mode 0V ≤ VCM ≤ 1.8V 90 Rejection Ratio 0V ≤ VCM ≤ 2.7V 76 dB min Power Supply 3V ≤ V+ ≤ 5V 79 PSRR Rejection Ratio VCM AV Input Common-Mode −0.25 0 0 V min Voltage Range 2.95 2.7 2.7 V max Large Signal RL = 10k 55 V/mV Voltage Gain VO Output Swing min RL = 10 kΩ 0.019 2.67 IS Supply Current Per Amplifier 510 0.08 0.08 V 0.112 0.112 max 2.66 2.66 V 2.25 2.25 min 800 800 µA 880 880 max 2.7V AC Electrical Characteristics Unless Otherwise Specified, All Limits Guaranteed for TJ = 25˚C, V+ = 2.7V, V− = 0V, VCM = VO = V+/2 and RL > 1 MΩ to V+/2. Boldface limits apply at the temperature extreme Symbol Parameter GBW Gain-Bandwidth Product φm Gm Conditions f = 50 kHz LM6144AI LM6144BI Typ LM6142AI LM6142BI (Note 5) Limit Limit (Note 6) (Note 6) Units 9 MHz Phase Margin 36 Deg Gain Margin 6 dB 5 www.national.com 24V Electrical Characteristics Unless Otherwise Specified, All Limits Guaranteed for TJ = 25˚C, V+ = 24V, V− = 0V, VCM = VO = V+/2 and RL > 1 MΩ to VS/2. Boldface limits apply at the temperature extreme Symbol VOS IB Parameter Conditions Input Offset Voltage LM6144AI LM6144BI Typ LM6142AI LM6142BI (Note 5) Limit Limit (Note 6) (Note 6) 1.3 Input Bias Current Units 2 3.8 mV 4.8 4.8 max 174 nA max IOS Input Offset Current 5 nA max RIN Input Resistance 288 MΩ CMRR Common Mode 0V ≤ VCM ≤ 23V 114 Rejection Ratio 0V ≤ VCM ≤ 24V 100 dB min Power Supply 0V ≤ VCM ≤ 24V 87 PSRR Rejection Ratio VCM AV Input Common-Mode −0.25 0 0 V min Voltage Range 24.25 24 24 V max Large Signal RL = 10k 500 RL = 10 kΩ 0.07 V/mV Voltage Gain VO Output Swing min 23.85 IS GBW Supply Current Gain-Bandwidth Product Per Amplifier 750 f = 50 kHz 18 0.15 0.15 V 0.185 0.185 max 23.81 23.81 V 23.62 23.62 min 1100 1100 µA 1150 1150 max MHz Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Charactenstics. Note 2: Human body model, 1.5 kΩ in series with 100 pF. Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150˚C. Note 4: The maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (Tj(max) − TA)/θJA. All numbers apply for packages soldered directly into a PC board. Note 5: Typical values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: For guaranteed military specifications see military datasheet MNLM6142AM-X. www.national.com 6 Typical Performance Characteristics Supply Current vs Supply Voltage TA = 25˚C, RL = 10 kΩ Unless Otherwise Specified Offset Voltage vs Supply Voltage Bias Current vs Supply Voltage DS012057-15 Offset Voltage vs VCM DS012057-16 Offset Voltage vs VCM DS012057-18 Bias Current vs VCM Offset Voltage vs VCM DS012057-19 Bias Current vs VCM DS012057-21 Open-Loop Transfer Function DS012057-17 DS012057-20 Bias Current vs VCM DS012057-22 Open-Loop Transfer Function DS012057-24 Open-Loop Transfer Function DS012057-25 7 DS012057-23 DS012057-26 www.national.com Typical Performance Characteristics TA = 25˚C, RL = 10 kΩ Unless Otherwise Specified (Continued) Output Voltage vs Source Current Output Voltage vs Source Current DS012057-27 Output Voltage vs Sink Current Output Voltage vs Source Current DS012057-28 Output Voltage vs Sink Current DS012057-30 Gain and Phase vs Load DS012057-29 Output Voltage vs Sink Current DS012057-31 Gain and Phase vs Load DS012057-33 DS012057-32 Distortion + Noise vs Frequency DS012057-34 DS012057-35 www.national.com 8 Typical Performance Characteristics TA = 25˚C, RL = 10 kΩ Unless Otherwise Specified (Continued) Open Loop Gain vs Load, 3V Supply GBW vs Supply Open Loop Gain vs Load, 5V Supply DS012057-36 DS012057-37 Open Loop Gain vs Load, 24V Supply DS012057-38 CMRR vs Frequency Unity Gain Freq vs VS DS012057-40 DS012057-41 DS012057-39 Crosstalk vs Frequency PSRR vs Frequency Noise Voltage vs Frequency DS012057-43 DS012057-42 9 DS012057-44 www.national.com Typical Performance Characteristics TA = 25˚C, RL = 10 kΩ Unless Otherwise Specified (Continued) Noise Current vs Frequency NE vs R Source DS012057-12 DS012057-45 LM6142/44 Application Ideas Slew Rate vs ∆ VIN VS = ± 5V The LM6142 brings a new level of ease of use to opamp system design. With greater than rail-to-rail input voltage range concern over exceeding the common-mode voltage range is eliminated. Rail-to-rail output swing provides the maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. The high gain-bandwidth with low supply current opens new battery powered applications, where high power consumption, previously reduced battery life to unacceptable levels. To take advantage of these features, some ideas should be kept in mind. ENHANCED SLEW RATE Unlike most bipolar opamps, the unique phase reversal prevention/speed-up circuit in the input stage causes the slew rate to be very much a function of the input signal amplitude. DS012057-7 FIGURE 1. This effect is most noticeable at higher supply voltages and lower gains where incoming signals are likely to be large. This new input circuit also eliminates the phase reversal seen in many opamps when they are overdriven. This speed-up action adds stability to the system when driving large capacitive loads. Figure 2 shows how excess input signal, is routed around the input collector-base junctions, directly to the current mirrors. The LM6142/44 input stage converts the input voltage change to a current change. This current change drives the current mirrors through the collectors of Q1–Q2, Q3–Q4 when the input levels are normal. If the input signal exceeds the slew rate of the input stage, the differential input voltage rises above two diode drops. This excess signal bypasses the normal input transistors, (Q1–Q4), and is routed in correct phase through the two additional transistors, (Q5, Q6), directly into the current mirrors. This rerouting of excess signal allows the slew-rate to increase by a factor of 10 to 1 or more. (See Figure 1.) As the overdrive increases, the opamp reacts better than a conventional opamp. Large fast pulses will raise the slewrate to around 30V to 60V/µs. www.national.com DRIVING CAPACITIVE LOADS Capacitive loads decrease the phase margin of all opamps. This is caused by the output resistance of the amplifier and the load capacitance forming an R-C phase lag network. This can lead to overshoot, ringing and oscillation. Slew rate limiting can also cause additional lag. Most opamps with a fixed maximum slew-rate will lag further and further behind when driving capacitive loads even though the differential input voltage raises. With the LM6142, the lag causes the slew rate to raise. The increased slew-rate keeps the output following the input much better. This effectively reduces phase lag. After the output has caught up with the input, the differential input voltage drops down and the amplifier settles rapidly. 10 LM6142/44 Application Ideas (Continued) DS012057-6 FIGURE 2. These features allow the LM6142 to drive capacitive loads as large as 1000 pF at unity gain and not oscillate. The scope photos (Figure 3 and Figure 4) above show the LM6142 driving a l000 pF load. In Figure 3, the upper trace is with no capacitive load and the lower trace is with a 1000 pF load. Here we are operating on ± 12V supplies with a 20 Vp-p pulse. Excellent response is obtained with a Cf of l0 pF. In Figure 4, the supplies have been reduced to ± 2.5V, the pulse is 4 Vp-p and Cf is 39 pF. The best value for the compensation capacitor is best established after the board layout is finished because the value is dependent on board stray capacity, the value of the feedback resistor, the closed loop gain and, to some extent, the supply voltage. Another effect that is common to all opamps is the phase shift caused by the feedback resistor and the input capacitance. This phase shift also reduces phase margin. This effect is taken care of at the same time as the effect of the capacitive load when the capacitor is placed across the feedback resistor. The circuit shown in Figure 5 was used for these scope photos. DS012057-9 FIGURE 4. DS012057-10 FIGURE 5. Typical Applications DS012057-8 FISH FINDER/ DEPTH SOUNDER. FIGURE 3. The LM6142/44 is an excellent choice for battery operated fish finders. The low supply current, high gain-bandwidth and full rail to rail output swing of the LM6142 provides an ideal combination for use in this and similar applications. 11 www.national.com Typical Applications (Continued) ANALOG TO DIGITAL CONVERTER BUFFER The high capacitive load driving ability, rail-to-rail input and output range with the excellent CMR of 82 dB, make the LM6142/44 a good choice for buffering the inputs of A to D converters. 3 OPAMP INSTRUMENTATION AMP WITH RAIL-TO-RAIL INPUT AND OUTPUT Using the LM6144, a 3 opamp instrumentation amplifier with rail-to-rail inputs and rail to rail output can be made. These features make these instrumentation amplifiers ideal for single supply systems. DS012057-13 Some manufacturers use a precision voltage divider array of 5 resistors to divide the common-mode voltage to get an input range of rail-to-rail or greater. The problem with this method is that it also divides the signal, so to even get unity gain, the amplifier must be run at high closed loop gains. This raises the noise and drift by the internal gain factor and lowers the input impedance. Any mismatch in these precision resistors reduces the CMR as well. Using the LM6144, all of these problems are eliminated. In this example, amplifiers A and B act as buffers to the differential stage (Figure 6). These buffers assure that the input impedance is over 100 MΩ and they eliminate the requirement for precision matched resistors in the input stage. They also assure that the difference amp is driven from a voltage source. This is necessary to maintain the CMR set by the matching of R1–R2 with R3–R4. www.national.com FIGURE 6. The gain is set by the ratio of R2/R1 and R3 should equal R1 and R4 equal R2. Making R4 slightly smaller than R2 and adding a trim pot equal to twice the difference between R2 and R4 will allow the CMR to be adjusted for optimum. With both rail to rail input and output ranges, the inputs and outputs are only limited by the supply voltages. Remember that even with rail-to-rail output, the output can not swing past the supplies so the combined common mode voltage plus the signal should not be greater than the supplies or limiting will occur. SPICE MACROMODEL A SPICE macromodel of this and many other National Semiconductor opamps is available at no charge from the NSC Customer Response Group at 800-272-9959. 12 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin Ceramic Sidebrazed Dual-In-Line Package Order Number LM6142AMJ-QML NS Package Number D08C 8-Pin Small Outline Package Order Number LM6142AIM or LM6142BIM NS Package Number M08A 13 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Pin Small Outline Package Order Number LM6144AIM or LM6144BIM NS Package Number M14A 8-Pin Molded Dual-In-Line Package Order Number LM6142AIN or LM6142BIN NS Package Number N08E www.national.com 14 inches (millimeters) unless otherwise noted (Continued) 14-Pin Molded Dual-In-Line Package Order Number LM6144AIN or LM6144BIN NS Package Number N14A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM6142 Dual and LM6144 Quad High Speed/Low Power 17 MHz Rail-to-Rail Input-Output Operational Amplifiers Physical Dimensions