Document 585-1 Shielded Power Inductors – LPS5015 • Very low DCR; excellent current handling • 5.0 × 5.0 mm footprint; less than 1.5 mm tall Designer’s Kit C350 contains 3 each of all values Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 102 – 107 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.57 mm pocket depth Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm PCB washing Only pure water or alcohol recommended Isat (A)5 Irms (A)6 DCR SRF 2 3 4 Inductance max typ 10% 20% 30% 20°C40°C Part number1 ±20% (µH) (Ohms)(MHz) drop drop drop rise rise LPS5015-102ML_ 1.0 0.050 1833.63.83.91.90 2.65 LPS5015-132ML_ 1.3 0.065 1502.52.62.81.70 2.35 LPS5015-182ML_ 1.8 0.075 1282.62.82.91.50 2.15 LPS5015-222ML_ 2.2 0.090 1162.42.62.71.40 2.00 LPS5015-332ML_ 3.3 0.125881.92.02.01.30 1.80 LPS5015-472ML_ 4.7 0.150731.61.71.81.20 1.62 LPS5015-562ML_ 5.6 0.175671.61.61.61.10 1.45 LPS5015-682ML_ 6.8 0.225571.31.41.50.90 1.25 LPS5015-822ML_ 8.2 0.280491.31.31.40.85 1.05 LPS5015-103ML_ 10 0.300441.21.31.30.80 0.95 LPS5015-123ML_ 12 0.350401.01.11.20.75 0.84 LPS5015-153ML_ 15 0.360 38 0.800.840.860.730.84 LPS5015-183ML_ 18 0.550 35 0.750.770.800.700.83 LPS5015-223ML_ 22 0.675 31 0.700.730.750.600.82 LPS5015-333ML_ 33 0.750 24 0.550.590.600.500.70 LPS5015-473ML_ 47 1.00 18 0.460.480.490.450.57 LPS5015-563ML_ 56 1.13 17 0.400.430.450.400.52 LPS5015-683ML_ 68 1.45 15 0.330.380.390.350.47 LPS5015-104ML_ 100 1.95 12 0.300.330.340.300.42 LPS5015-124ML_ 120 2.50 10 0.250.280.300.270.37 LPS5015-154ML_ 150 3.40 9.3 0.230.250.260.250.33 LPS5015-224ML_ 220 4.50 7.3 0.200.210.220.220.29 LPS5015-334ML_ 330 7.40 5.7 0.150.170.180.170.22 LPS5015-474ML_ 470 7.50 4.9 0.120.120.130.160.21 LPS5015-564ML_ 560 8.50 4.3 0.100.110.120.140.190 LPS5015-684ML_ 680 10.6 4.0 0.100.110.110.130.175 LPS5015-105ML_ 1000 15.0 3.20.0800.0900.0930.10 0.150 LPS5015-155ML_ 1500 25.0 2.50.0800.0860.0880.0900.140 LPS5015-185ML_ 1800 28.0 2.20.0780.0830.0860.0850.130 LPS5015-225ML_ 2200 36.0 2.10.0720.0780.0800.0650.090 LPS5015-335ML_ 3300 55.0 1.70.0640.0720.0760.0550.075 LPS5015-475ML_ 4700 80.0 1.40.0620.0690.0720.0450.065 1. Please specify termination and packaging codes: LPS5015-335MLC Termination:L=RoHS compliant silver-palladiumplatinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tinlead (63/37). Packaging:C =7″ machine-ready reel. EIA-481 embossed plastic tape 1000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 8753ES or equivalent. 5. DC current that causes the specified inductance drop from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 585-1 Revised 12/08/11 Document 585-2 Shielded Power Inductors – LPS5015 Series Typical L vs Frequency Typical L vs Current 10000 10000 3300 µH 3300 µH 1000 µH 330 µH 100 µH 100 33 µH 10 µH 10 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 330 µH 100 µH 100 33 µH 10 µH 10 3.3 µH 3.3 µH 1 0.01 1 0.1 10 Frequency (MHz) Typical Current Derating 1 0.01 0.1 XXX X 90 80 70 Dash number 60 Winding direction 0.0551 ±0.004 ** 1,4 ±0,1 40 20 Isat Irms -40 -20 0 20 Recommended Land Pattern 0.060 1,50 40 60 10 Internal code 50 25°C Percent of rated current 0.189 ±0.003* 4,80 ±0,076 100 30 1 0.189 ±0.003* 4,80 ±0,076 120 110 10 0 Current (A) 80 100 120 140 0.134 3,40 0.039 typ 1,00 Ambient temperature (°C) 0.217 5,51 0.0665 1,689 0.134 3,40 0.134 3,40 0.060 0.039 typ 1,00 1,52 are of the case not * Dimensions including the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. 0.134 3,40 0.217 5,51 **For optional tin-lead and tin-silver-copper terminations, dimensions are for the mounted part. Dimensions before mounting can be an additional 0.005 inch (0,13 mm). Dimensions are in inches mm Document 585-2 Revised 12/08/11