LTC2754 Quad 12-/16-Bit SoftSpan IOUT DACs FEATURES DESCRIPTION n The LTC®2754 is a family of quad 12- and 16-bit multiplying serial-input, current-output digital-to-analog converters. They operate from a single 3V to 5V supply and are guaranteed monotonic over temperature. The LTC2754A-16 provides full 16-bit performance (±1LSB INL and DNL, max) over temperature without any adjustments. These SoftSpan™ DACs offer six output ranges (up to ±10V) that can be programmed through the 3-wire SPI serial interface, or pinstrapped for operation in a single range. n n n n n n n n n n Program or Pin-Strap Six Output Ranges 0V to 5V, 0V to 10V, –2.5V to 7.5V, ±2.5V, ±5V, ±10V Maximum 16-Bit INL Error: ±1 LSB over Temperature Guaranteed Monotonic over Temperature Low Glitch Impulse 0.26nV•s (3V), 1.25nV•s (5V) Serial Readback of All On-Chip Registers Low 1μA Maximum Supply Current 2.7V to 5.5V Single-Supply Operation 16-Bit Settling Time: 2μs Voltage-Controlled Offset and Gain Trims Clear and Power-On-Reset to 0V Regardless of Output Range 52-Pin 7mm × 8mm QFN Package The content of any on-chip register (including DAC output-range settings) can be verified in just one instruction cycle; and if you change any register, that register will be automatically read back during the next instruction cycle. Voltage-controlled offset and gain adjustments are also provided; and the power-on reset circuit and CLR pin both reset the DAC outputs to 0V regardless of output range. APPLICATIONS ■ ■ ■ ■ High Resolution Offset and Gain Adjustment Process Control and Industrial Automation Automatic Test Equipment Data Acquisition Systems L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. SoftSpan is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 5481178. TYPICAL APPLICATION Quad 16-Bit VOUT DAC with Software-Selectable Ranges RINB RCOMB GEADJB REFB ROFSB REFA ROFSA GEADJA RCOMA VOSADJA IOUT2A IOUT1A 1.0 VOSADJB IOUT2B DAC A IOUT1B DAC B RFBA + – 0.6 VOUTB LTC2754-16 RFBD RFBC IOUT1D IOUT2D IOUT1C DAC D IOUT2C DAC C – + VOUTC 0.4 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 RINC REFC ROFSC REFD ROFSD R GEADJC COMC GEADJD – + + – VREFD RCOMD VOSADJC GND M-SPAN RIND VOSADJD VDD = 5V VREF = 5V ±10V RANGE 0.8 RFBB SPI with READBACK + – VOUTD LTC2754-16 Integral Nonlinearity (INL) INL (LSB) – + VOUTA RINA VDD VREFB + – – + VREFA 0 ALL AMPLIFIERS 1/2 LT1469 16384 32768 CODE 49152 65535 2754 G01 VREFC 2754 TA01 2754f 1 LTC2754 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Notes 1, 2) RCOMB REFB ROFSB RFBB IOUT1B VOSADJB VOSADJA IOUT1A RFBA ROFSA REFA TOP VIEW RCOMA IOUT1X , IOUT2X to GND ............................................±0.3V RINX, RCOMX , REFX, RFBX , ROFSX , VOSADJX , GEADJX to GND ........................................................±18V VDD to GND .................................................. –0.3V to 7V Digital Inputs and Outputs to GND ................ –0.3V to VDD+0.3V (max 7V) Operating Temperature Range LTC2754C ................................................ 0°C to 70°C LTC2754I..............................................–40°C to 85°C Maximum Junction Temperature........................... 150°C Storage Temperature Range...................–65°C to 150°C 52 51 50 49 48 47 46 45 44 43 42 41 40 GEADJB GEADJA 1 RINA 2 39 RINB IOUT2A 3 38 IOUT2B GND 4 37 GND CS/LD 5 36 LDAC SDI 6 35 S2 SCK 7 34 S1 53 SRO 8 33 S0 SROGND 9 32 M-SPAN VDD 10 31 RFLAG GND 11 30 CLR IOUT2D 12 29 IOUT2C 28 RINC RIND 13 27 GEADJC GEADJD 14 RCOMC REFC ROFSC RFBC IOUT1C VOSADJC VOSADJD IOUT1D RFBD ROFSD REFD RCOMD 15 16 17 18 19 20 21 22 23 24 25 26 UKG PACKAGE 52-LEAD (7mm s 8mm) PLASTIC QFN TJMAX = 150°C, θJA = 29°C/W EXPOSED PAD (PIN 53) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2754CUKG-12#PBF LTC2754CUKG-12#TRPBF LTC2754UKG-12 52-Lead (7mm × 8mm) Plastic QFN 0°C to 70°C LTC2754IUKG-12#PBF LTC2754IUKG-12#TRPBF LTC2754UKG-12 52-Lead (7mm × 8mm) Plastic QFN –40°C to 85°C LTC2754BCUKG-16#PBF LTC2754BCUKG-16#TRPBF LTC2754UKG-16 52-Lead (7mm × 8mm) Plastic QFN 0°C to 70°C LTC2754BIUKG-16#PBF LTC2754UKG-16 52-Lead (7mm × 8mm) Plastic QFN –40°C to 85°C LTC2754ACUKG-16#PBF LTC2754ACUKG-16#TRPBF LTC2754UKG-16 52-Lead (7mm × 8mm) Plastic QFN 0°C to 70°C LTC2754AIUKG-16#PBF LTC2754UKG-16 52-Lead (7mm × 8mm) Plastic QFN –40°C to 85°C LTC2754BIUKG-16#TRPBF LTC2754AIUKG-16#TRPBF Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 2754f 2 LTC2754 ELECTRICAL CHARACTERISTICS VDD = 5V, VREF = 5V unless otherwise specified. The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. SYMBOL PARAMETER CONDITIONS MIN LTC2754-12 TYP MAX MIN LTC2754B-16 TYP MAX MIN LTC2754A-16 TYP MAX UNITS Static Performance Resolution ● 12 12 16 16 Bits Monotonicity ● DNL Differential Nonlinearity ● ±1 ±1 ±0.2 ±1 LSB INL Integral Nonlinearity ● ±1 ±2 ±0.4 ±1 LSB GE Gain Error All Output Ranges ±2 ±20 ±2 ±12 LSB Gain Error Temperature Coefficient ΔGain/ΔTemp Bipolar Zero Error All Bipolar Ranges BZE ● 16 ±0.5 ±1 ● Bipolar Zero Temperature Coefficient ±0.2 ±1 ±1 ±0.5 VDD = 5V, ±10% VDD = 3V, ±10% PSR Power Supply Rejection ILKG IOUT1 Leakage Current TA = 25°C TMIN to TMAX ● ● 16 ±0.05 ● ±1 ±12 ±1 ±0.5 ±0.025 ±0.06 ±2 ±5 Bits ppm/°C ±8 ±0.5 ppm/°C ±0.4 ±1 ±0.03 ±0.1 ±0.2 ±0.5 ±2 ±5 ±0.05 ±2 ±5 ±0.05 LSB LSB/V LSB/V nA nA VDD = 5V, VREF = 5V unless otherwise specified. The ● denotes specifications that apply over the full operating temperature range, otherwise specifications are at TA = 25°C. SYMBOL PARAMETER CONDITIONS Reference Inverting Resistors (Note 4) MIN TYP MAX UNITS ● 16 20 kΩ ● 8 10 kΩ Analog Pins RREF DAC Input Resistance RFB Feedback Resistors (Note 3) ● 8 10 kΩ ROFS Bipolar Offset Resistors (Note 3) ● 16 20 kΩ RVOSADJ Offset Adjust Resistors ● 1024 1280 kΩ RGEADJ Gain Adjust Resistors ● 2048 2560 kΩ CIOUT1 Output Capacitance Full-Scale Zero-Scale 75 45 pF Output Settling Time 0V to 10V Range, 10V Step. To ±0.0015% FS (Note 5) 2 μs Glitch Impulse VDD = 5V (Note 6) VDD = 3V (Note 6) Digital-to-Analog Glitch Impulse Dynamic Performance THD 1.25 0.26 nV•s nV•s (Note 7) 2 nV•s Reference Multiplying BW 0V to 5V Range, VREF = 3VRMS, Code = Full Scale, –3dB BW 2 MHz Multiplying Feedthrough Error 0V to 5V Range, VREF = ±10V, 10kHz Sine Wave 0.5 mV Analog Crosstalk (Note 8) –109 dB Total Harmonic Distortion (Note 9) Multiplying –110 Output Noise Voltage Density (Note 10) at IOUT1 13 dB nV/√Hz 2754f 3 LTC2754 ELECTRICAL CHARACTERISTICS VDD = 5V, VREF = 5V unless otherwise specified. The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Power Supply ● VDD Supply Voltage IDD Supply Current, VDD Digital Inputs = 0V or VDD ● VIH Digital Input High Voltage 3.3V ≤ VDD ≤ 5.5V 2.7V ≤ VDD < 3.3V ● ● VIL Digital Input Low Voltage 4.5V < VDD ≤ 5.5V 2.7V ≤ VDD ≤ 4.5V ● ● 2.7 0.5 5.5 V 1 μA Digital Inputs 2.4 2 V V 0.8 0.6 Hysteresis Voltage 0.1 V V V IIN Digital Input Current VIN = GND to VDD ● ±1 μA CIN Digital Input Capacitance VIN = 0V (Note 11) ● 6 pF VOH IOH = 200μA 2.7V ≤ VDD ≤ 5.5V ● VOL IOL = 200μA 2.7V ≤ VDD ≤ 5.5V ● 0.4 V Digital Outputs TIMING CHARACTERISTICS VDD – 0.4 V The ● denotes specifications that apply over the full operating temperature range, otherwise specifications are at TA = 25°C. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VDD = 4.5V to 5.5V t1 SDI Valid to SCK Set-Up ● 7 ns t2 SDI Valid to SCK Hold ● 7 ns t3 SCK High Time ● 11 ns t4 SCK Low Time ● 11 ns t5 CS/LD Pulse Width ● 9 ns t6 LSB SCK High to CS/LD High ● 4 ns t7 CS/LD Low to SCK Positive Edge ● 4 ns t8 CS/LD High to SCK Positive Edge ● 4 ns CLOAD = 10pF ● t9 SRO Propagation Delay t10 CLR Pulse Width Low ● 36 18 ns ns t11 LDAC Pulse Width Low ● 15 ns t12 CLR Low to RFLAG Low CLOAD = 10pF (Note 11) ● 50 ns t13 CS/LD High to RFLAG High CLOAD = 10pF (Note 11) ● 40 ns SCK Frequency 50% Duty Cycle (Note 12) ● 40 MHz VDD = 2.7V to 3.3V ● t1 SDI Valid to SCK Set-Up 9 ns t2 SDI Valid to SCK Hold (Note 11) ● 9 ns t3 SCK High Time CL = 10pF ● 15 ns t4 SCK Low Time ● 15 ns t5 CS/LD Pulse Width ● 12 ns t6 LSB SCK High to CS/LD High ● 5 ns 2754f 4 LTC2754 TIMING CHARACTERISTICS The ● denotes specifications that apply over the full operating temperature range, otherwise specifications are at TA = 25°C. SYMBOL PARAMETER t7 CS/LD Low to SCK Positive Edge CONDITIONS ● MIN 5 TYP ns t8 CS/LD High to SCK Positive Edge ● 5 ns t9 SRO Propagation Delay t10 t11 t12 CLR Low to RFLAG Low CLOAD = 10pF (Note 11) ● 70 ns t13 CS/LD High to RFLAG high CLOAD = 10pF (Note 11) ● 60 ns SCK Frequency 50% Duty Cycle (Note 12) ● 25 MHz ● CLOAD = 10pF MAX UNITS 26 ns CLR Pulse Width Low ● 60 ns LDAC Pulse Width Low ● 20 ns Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 3: Because of the proprietary SoftSpan switching architecture, the measured resistance looking into each of the specified pins is constant for all output ranges if the IOUT1X and IOUT2X pins are held at ground. Note 4: Input resistors measured from RINX to RCOMX ; feedback resistors measured from RCOMX to REFX. Note 5: Using LT1469 with CFEEDBACK = 15pF. A ±0.0015% settling time of 1.7μs can be achieved by optimizing the time constant on an individual basis. See Application Note 74, Component and Measurement Advances Ensure 16-Bit DAC Settling Time. Note 6: Measured at the major carry transition, 0V to 5V range. Output amplifier: LT1469; CFB = 27pF. Note 7. Full-scale transition; REF = 0V. Note 8. Analog Crosstalk is defined as the AC voltage ratio VOUTB/VREFA , expressed in dB. REFB is grounded, and DAC B is set to 0V-5V span and zero-, mid- or full- scale code. VREFA is a 3VRMS, 1kHz sine wave. Crosstalk between other DAC channels is similar or better. Note 9. REF = 6VRMS at 1kHz. 0V to 5V range. DAC code = FS. Output amplifier = LT1469. Note 10. Calculation from Vn = √4kTRB, where k = 1.38E-23 J/°K (Boltzmann constant), R = resistance (Ω), T = temperature (°K), and B = bandwidth (Hz). 0V to 5V Range; zero-, mid-, or full- scale. Note 11. Guaranteed by design, not subject to test. Note 12. When using SRO, maximum SCK frequency fMAX is limited by SRO propagation delay t9 as follows: ⎛ ⎞ 1 ⎟ fMAX = ⎜⎜ ⎟ ⎝ 2 (t 9 + t S ) ⎠ , where tS is the setup time of the receiving device. TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C, unless otherwise noted. LTC2754-16 1.0 VDD = 5V VREF = 5V ±10V RANGE 0.8 0.6 1.0 VDD = 5V 0.8 VREF = 5V ±10V RANGE 0.6 VDD = 5V VREF = 5V ±10V RANGE 0.8 0.6 0.4 0.4 0.2 0.2 0 –0.2 INL (LSB) 0.4 0.2 DNL (LSB) INL (LSB) INL vs Temperature Differential Nonlinearity (DNL) Integral Nonlinearity (INL) 1.0 0 –0.2 0.0 –0.4 –0.4 –0.4 –0.6 –0.6 –0.8 –0.8 –0.8 –1.0 –1.0 –1.0 –40 16384 32768 CODE 49152 65535 2754 G01 0 16384 32768 CODE 49152 65535 2754 G02 –INL –0.2 –0.6 0 +INL –20 20 40 0 60 TEMPERATURE (°C) 80 2754 G03 2754f 5 LTC2754 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C, unless otherwise noted. LTC2754-16 DNL vs Temperature Bipolar Zero vs Temperature 1.0 8 VDD = 5V 0.8 VREF = 5V ±10V RANGE 0.6 6 VDD = 5V VREF = 5V ±10V RANGE 12 4 +DNL 0.0 –DNL –0.2 VDD = 5V VREF = 5V ±10V RANGE 8 2 4 GE (LSB) 0.2 BZE (LSB) 0.4 DNL (LSB) Gain Error vs Temperature 16 ±0.5ppm/°C (TYP) 0 ±1ppm/°C (TYP) 0 –2 –4 –4 –8 –6 –12 –0.4 –0.6 –0.8 –1.0 –40 –20 20 40 0 60 TEMPERATURE (°C) –8 –40 80 –20 0 40 60 20 TEMPERATURE (°C) 2754 G04 0 40 60 20 TEMPERATURE (°C) 80 2754 G06 DNL vs VREF 1.0 1.0 0.6 0.6 VDD = 5V 0.8 ±5V RANGE VDD = 5V 0.8 ±5V RANGE 0.4 0.4 +INL +INL 0.2 0.0 –INL –INL –0.2 INL (LSB) INL (LSB) –20 2754 G05 INL vs VREF 0.2 0.0 –0.4 –0.6 –0.6 –0.8 –0.8 4 2 0 2 VREF (V) 4 6 8 –DNL 4 2 0 2 VREF (V) 0 0.6 ATTENUATION (dB) –20 +INL –INL –0.2 –0.4 –0.6 –40 –60 –80 –100 3 3.5 6 8 10 2754 G08 ALL BITS ON D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 UNIPOLAR 5V OUTPUT RANGE LT1469 OUTPUT AMPLIFIER CFEEDBACK = 8.2pF –0.8 –1.0 2.5 4 Multiplying Frequency Response vs Digital Code 0.8 0.0 –DNL 2754 G07 1.0 0.2 +DNL –1.0 –10 –8 –6 10 INL vs VDD 0.4 +DNL –0.2 –0.4 –1.0 –10 –8 –6 INL (LSB) –16 –40 80 4 4.5 5 5.5 VDD (V) 2754 G09 –120 100 ALL BITS OFF 1k 10k 100k FREQUENCY (Hz) 1M 10M 2754 G10 2754f 6 LTC2754 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C, unless otherwise noted. LTC2754-12 Integral Nonlinearity (INL) Differential Nonlinearity (DNL) 1.0 1.0 VDD = 5V VREF = 5V ±10V RANGE 0.8 0.6 0.4 0.4 0.2 0.2 DNL (LSB) INL (LSB) 0.6 0 –0.2 –0.2 –0.4 –0.6 –0.6 –0.8 –0.8 –1.0 –1.0 1024 2048 CODE 4095 3072 0 1024 2048 CODE 3072 2754 G11 LTC2754 CLR, LDAC, SDI, SCK, CS/LD TIED TOGETHER LOGIC THRESHOLD (V) 4 3 2 VDD = 5V 1 Supply Current vs Clock Frequency 2 100 1.75 10 1.5 SUPPLY CURRENT (mA) 5 4095 2754 G12 Logic Threshold vs Supply Voltage Supply Current vs Logic Input Voltage SUPPLY CURRENT (mA) 0 –0.4 0 VDD = 5V VREF = 5V ±10V RANGE 0.8 RISING 1.25 FALLING 1 0.75 1 VDD = 5V 0.1 VDD = 3V 0.01 0.001 VDD = 3V 0 0 1 3 4 2 DIGITAL INPUT VOLTAGE (V) 5 0.5 2.5 3 3.5 4 4.5 5 5.5 1 VDD (V) Settling 0V to 10V CS/LD 5V/DIV 0.26nV•s TYP CS/LD 5V/DIV 1.25nV•s TYP GATED SETTLING WAVEFORM 250μV/DIV VOUT 5mV/DIV VOUT 5mV/DIV 2754 G16 RISING MAJOR CARRY TRANSITION. FALLING TRANSITION IS SIMILAR OR BETTER 100M 2754 G15 Midscale Glitch Midscale Glitch CS/LD 2V/DIV 100 10k 1M SCK FREQUENCY (Hz) 2754 G14 2754 G13 VDD = 3V 500ns/DIV VREF = 5V 5V RANGE LT1468 OUTPUT AMPLIFIER CFEEDBACK = 27pF 0.0001 VDD = 5V 500ns/DIV VREF = 5V 5V RANGE LT1468 OUTPUT AMPLIFIER CFEEDBACK = 27pF 2754 G17 500ns/DIV USING LT1469 AMP CFEEDBACK = 12pF 0V TO 10V STEP 2754 G17 RISING MAJOR CARRY TRANSITION. FALLING TRANSITION IS SIMILAR OR BETTER 2754f 7 LTC2754 PIN FUNCTIONS GEADJA (Pin1): Gain Adjust Pin for DAC A. This control pin can be used to null gain error or to compensate for reference errors. Nominal adjustment range is ±512 LSB (LTC2754-16) for a voltage input range of ±VRINA (i.e., ±5V for a 5V reference input). Tie to ground if not used. Applications). Any or all of these precision-matched resistor sets (Each set comprising RINX, RCOMX and REFX) may be used to invert one or more positive reference voltages to the negative voltages needed by the DACs. Typically 5V; accepts up to ±15V. RINA (Pin 2): Input Resistor for Reference Inverting Amplifier. The 20k input resistor is connected internally from RINA to RCOMA. For normal operation tie RINA to the external reference voltage VREFA (see Typical Applications). Any or all of these precision-matched resistor sets (Each set comprising RINX, RCOMX and REFX) may be used to invert one or more positive reference voltages to the negative voltages needed by the DACs. Typically 5V; accepts up to ±15V. GEADJD (Pin 14): Gain Adjust Pin for DAC D. This control pin can be used to null gain error or to compensate for reference errors. Nominal adjustment range is ±512 LSB (LTC2754-16) for a voltage input range of ±VRIND (i.e., ±5V for a 5V reference input). Tie to ground if not used. IOUT2A (Pin 3): DAC A Current Output Complement. Tie IOUT2A to ground. GND (Pin 4): Ground; provides shielding for IOUT2A. Tie to ground. CS/LD (Pin 5): Synchronous Chip Select and Load Pin. SDI (Pin 6): Serial Data Input. Data is clocked in on the rising edge of the serial clock (SCK) when CS/LD is low. SCK (Pin 7): Serial Clock. SRO (Pin 8): Serial Readback Output. Data is clocked out on the falling edge of SCK. Readback data begins clocking out after the last address bit A0 is clocked in. SRO is an active output only when the chip is selected (i.e., when CS/LD is low). Otherwise SRO presents a high-impedance output in order to allow other parts to control the bus. SROGND (Pin 9): Ground pin for SRO. Tie to ground. VDD (Pin 10): Positive Supply Input; 2.7V ≤ VDD ≤ 5.5V. Bypass with a 0.1μF low-ESR ceramic capacitor to ground. GND (Pin 11): Ground. Tie to ground. IOUT2D (Pin 12): DAC D Current Output Complement. Tie IOUT2D to ground. RIND (Pin 13): Input Resistor for Reference Inverting Amplifier. The 20k input resistor is connected internally from RIND to RCOMD. For normal operation tie RIND to the external reference voltage VREFD (see Typical RCOMD (Pin 15): Center Tap Point for Reference Amplifier Inverting Resistors. The 20k reference inverting resistors are connected internally from RIND to RCOMD and from RCOMD to REFD, respectively (see Block Diagram). For normal operation tie RCOMD to the negative input of external reference inverting amplifier (see Typical Applications). REFD (Pin 16): Inverted Reference Voltage for DAC D, with internal connection to the reference inverting resistor. The 20k resistor is connected internally from REFD to RCOMD . For normal operation tie this pin to the output of reference inverting amplifier (see Typical Applications). Typically –5V; accepts up to ±15V. The impedance looking into this pin is 10k to ground (RIND and RCOMD floating). ROFSD (Pin 17): Bipolar Offset Network for DAC D. This pin provides the translation of the output voltage range for bipolar spans. Accepts up to ±15V; for normal operation tie to the positive reference voltage at RIND (Pin 13). The impedance looking into this pin is 20k to ground. RFBD (Pin 18): DAC D Feedback Resistor. For normal operation tie to the output of the I/V converter amplifier for DAC D (see Typical Applications). The DAC output current from IOUT1D flows through the feedback resistor to the RFBD pin. The impedance looking into this pin is 10k to ground. IOUT1D (Pin 19): DAC D Current Output. This pin is a virtual ground when the DAC is operating and should reside at 0V. For normal operation tie to the negative input of the I/V converter amplifier for DAC D (see Typical Applications). 2754f 8 LTC2754 PIN FUNCTIONS VOSADJD (Pin 20): DAC D Offset Adjust Pin. This control pin can be used to null unipolar offset or bipolar zero error. The offset voltage delta is inverted and attenuated such that a 5V control voltage applied to VOSADJD produces ΔVOS = -512 LSB (LTC2754-16) in any output range (assumes a 5V reference voltage at RIND). Tie to ground if not used. VOSADJC (Pin 21): DAC C Offset Adjust Pin. This control pin can be used to null unipolar offset or bipolar zero error. The offset voltage delta is inverted and attenuated such that a 5V control voltage applied to VOSADJC produces ΔVOS = -512 LSB (LTC2754-16) in any output range (assumes a 5V reference voltage at RINC). Tie to ground if not used. IOUT1C (Pin 22): DAC C Current Output. This pin is a virtual ground when the DAC is operating and should reside at 0V. For normal operation tie to the negative input of the I/V converter amplifier for DAC C (see Typical Applications). RFBC (Pin 23): DAC C Feedback Resistor. For normal operation tie to the output of the I/V converter amplifier for DAC C (see Typical Applications). The DAC output current from IOUT1D flows through the feedback resistor to the RFBC pin. The impedance looking into this pin is 10k to ground. ROFSC (Pin 24): Bipolar Offset Network for DAC C. This pin provides the translation of the output voltage range for bipolar spans. Accepts up to ±15V; for normal operation tie to the positive reference voltage at RINC (Pin 28). The impedance looking into this pin is 20k to ground. REFC (Pin 25): Inverted Reference Voltage for DAC C, with internal connection to the reference inverting resistor. The 20k resistor is connected internally from REFC to RCOMC. For normal operation tie this pin to the output of reference inverting amplifier (see Typical Applications). Typically –5V; accepts up to ±15V. The impedance looking into this pin is 10k to ground (RINC and RCOMC floating). RCOMC (Pin 26): Center Tap Point for Reference Amplifier Inverting Resistors. The 20k reference inverting resistors are connected internally from RINC to RCOMC and from RCOMC to REFC, respectively (see Block Diagram). For normal operation tie RCOMC to the negative input of external reference inverting amplifier (see Typical Applications). GEADJC (Pin 27): Gain Adjust Pin for DAC C. This control pin can be used to null gain error or to compensate for reference errors. Nominal adjustment range is ±512 LSB (LTC2754-16) for a voltage input range of ±VRINC (i.e., ±5V for a 5V reference input). Tie to ground if not used. RINC (Pin 28): Input Resistor for Reference Inverting Amplifier. The 20k input resistor is connected internally from RINC to RCOMC. For normal operation tie RINC to the external reference voltage VREFC (see Typical Applications). Any or all of these precision-matched resistor sets (Each set comprising RINX, RCOMX and REFX) may be used to invert one or more positive reference voltages to the negative voltages needed by the DACs. Typically 5V; accepts up to ±15V. IOUT2C (Pin 29): DAC C Current Output Complement. Tie IOUT2C to ground. CLR (Pin 30): Asynchronous Clear Pin. When this pin is low, all DAC registers (both code and span) are cleared to zero. All DAC outputs are cleared to zero volts. RFLAG (Pin 31): Reset Flag Pin. An active low output is asserted when there is a power-on reset or a clear event. Returns high when an Update command is executed. M-SPAN (Pin 32): Manual Span Control Pin. M-SPAN is used in conjunction with pins S2, S1 and S0 (Pins 33, 34 and 35) to configure all DACs for operation in a single, fixed output range. To configure the part for manual-span use, tie M-SPAN directly to VDD . The active output range is then set via hardware pin strapping of pins S2, S1 and S0 (rather than through the SPI port); and Write and Update commands have no effect on the active output span. To configure the part for SoftSpan use, tie M-SPAN directly to GND. The output ranges are then individually and dynamically controllable through the SPI port; and pins S2, S1 and S0 have no effect. See ‘Manual Span Configuration’ in the Operation section. M-SPAN must be connected either directly to GND (SoftSpan configuration) or to VDD (manual-span configuration). 2754f 9 LTC2754 PIN FUNCTIONS S0 (Pin 33): Span Bit 0. In Manual Span mode (M-SPAN tied to VDD), Pins S0, S1 and S2 are pin-strapped to select a single fixed output range for all DACs. These pins should be tied to either GND or VDD even if they are unused. S1 (Pin 34): Span Bit 1. In Manual Span mode (M-SPAN tied to VDD), Pins S0, S1 and S2 are pin-strapped to select a single fixed output range for all DACs. These pins should be tied to either GND or VDD even if they are unused. S2 (Pin 35): Span Bit 2. In Manual Span mode (M-SPAN tied to VDD), Pins S0, S1 and S2 are pin-strapped to select a single fixed output range for all DACs. These pins should be tied to either GND or VDD even if they are unused. LDAC (Pin 36): Asynchronous DAC Load Input. When LDAC is a logic low, all DACs are updated (CS/LD must be high). GND (Pin 37): Ground; provides shielding for IOUT2B. Tie to ground. IOUT2B (Pin 38): DAC B Current Output Complement. Tie IOUT2B to ground. RINB (Pin 39): Input Resistor for Reference Inverting Amplifier. The 20k input resistor is connected internally from RINB to RCOMB . For normal operation tie RINB to the external reference voltage VREFB (see Typical Applications). Any or all of these precision-matched resistor sets (Each set comprising RINX , RCOMX and REFX) may be used to invert one or more positive reference voltages to the negative voltages needed by the DACs. Typically 5V; accepts up to ±15V. GEADJB (Pin 40): Gain Adjust Pin for DAC B. This control pin can be used to null gain error or to compensate for reference errors. Nominal adjustment range is ±512 LSB (LTC2754-16) for a voltage input range of ±VRINB (i.e., ±5V for a 5V reference input). Tie to ground if not used. RCOMB (Pin 41): Center Tap Point for Reference Amplifier Inverting Resistors. The 20k reference inverting resistors are connected internally from RINB to RCOMB and from RCOMB to REFB, respectively (see Block Diagram). For normal operation tie RCOMB to the negative input of external reference inverting amplifier (see Typical Applications). REFB (Pin 42): Inverted Reference Voltage for DAC B, with internal connection to the reference inverting resistor. The 20k resistor is connected internally from REFB to RCOMB . For normal operation tie this pin to the output of reference inverting amplifier (see Typical Applications). Typically –5V; accepts up to ±15V. The impedance looking into this pin is 10k to ground (RINB and RCOMB floating). ROFSB (Pin 43): Bipolar Offset Network for DAC B. This pin provides the translation of the output voltage range for bipolar spans. Accepts up to ±15V; for normal operation tie to the positive reference voltage at RINB (Pin 39). The impedance looking into this pin is 20k to ground. RFBB (Pin 44): DAC B Feedback Resistor. For normal operation tie to the output of the I/V converter amplifier for DAC B (see Typical Applications). The DAC output current from IOUT1B flows through the feedback resistor to the RFBB pin. The impedance looking into this pin is 10k to ground. IOUT1B (Pin 45): DAC B Current Output. This pin is a virtual ground when the DAC is operating and should reside at 0V. For normal operation tie to the negative input of the I/V converter amplifier for DAC B (see Typical Applications). VOSADJB (Pin 46): DAC B Offset Adjust Pin. This control pin can be used to null unipolar offset or bipolar zero error. The offset-voltage delta is inverted and attenuated such that a 5V control voltage applied to VOSADJB produces ΔVOS = –512 LSB (LTC2754-16) in any output range (assumes a 5V reference voltage at RINB). Tie to ground if not used. VOSADJA (Pin 47): DAC A Offset Adjust Pin. This control pin can be used to null unipolar offset or bipolar zero error. The offset-voltage delta is inverted and attenuated such that a 5V control voltage applied to VOSADJA produces ΔVOS = –512 LSB (LTC2754-16) in any output range (assumes a 5V reference voltage at RINA). Tie to ground if not used. IOUT1A (Pin 48): DAC A Current Output. This pin is a virtual ground when the DAC is operating and should reside at 0V. For normal operation tie to the negative input of the I/V converter amplifier for DAC A (see Typical Applications). RFBA (Pin 49): DAC A Feedback Resistor. For normal operation tie to the output of the I/V converter amplifier for DAC A (see Typical Applications). The DAC output current from IOUT1A flows through the feedback resistor to the RFBA pin. The impedance looking into this pin is 10k to ground. 2754f 10 LTC2754 PIN FUNCTIONS ROFSA (Pin 50): Bipolar Offset Network for DAC A. This pin provides the translation of the output voltage range for bipolar spans. Accepts up to ±15V; for normal operation tie to the positive reference voltage at RINA (Pin 2). The impedance looking into this pin is 20k to ground. REFA (Pin 51): Inverted Reference Voltage for DAC A, with internal connection to the reference inverting resistor. The 20k resistor is connected internally from REFA to RCOMA. For normal operation tie this pin to the output of reference inverting amplifier (see Typical Applications). Typically –5V; accepts up to ±15V. The impedance looking into this pin is 10k to ground (RINA and RCOMA floating). RCOMA (Pin 52): Center Tap Point for Reference Amplifier Inverting Resistors. The 20k reference inverting resistors are connected internally from RINA to RCOMA and from RCOMA to REFA, respectively (see Block Diagram). For normal operation tie RCOMA to the negative input of external reference inverting amplifier (see Typical Applications). Exposed Pad (Pin 53): Ground. The Exposed Pad must be soldered to the PCB. BLOCK DIAGRAM 10 RINA 2 VDD 2.56M 2.56M GEADJA 1 20k 40 GEADJB 20k RCOMA 52 39 RINB 41 RCOMB LTC2754-16 20k 20k REFA 51 42 REFB ROFSA 50 43 ROFSB 16 RFBA 49 DAC REG DAC A 16-BIT WITH SPAN SELECT IOUT1A 48 IOUT2A 3 DATA REGISTERS 3 DATA REGISTERS INPUT REG INPUT REG SPAN REGISTERS DAC REG SPAN REGISTERS INPUT REG 16 DAC REG INPUT REG 3 DAC REG 44 RFBB DAC B 16-BIT WITH SPAN SELECT 45 IOUT1B 38 IOUT2B VOSADJA 47 46 VOSADJB VOSADJD 20 21 VOSADJC 16 DAC REG DAC D 16-BIT WITH SPAN SELECT IOUT2D 12 IOUT1D 19 DATA REGISTERS 3 DATA REGISTERS INPUT REG INPUT REG SPAN REGISTERS DAC REG SPAN REGISTERS INPUT REG 16 DAC REG INPUT REG 3 DAC REG DAC C B 16-BIT WITH SPAN SELECT 29 IOUT2C 22 IOUT1C RFBD 18 23 RFBC ROFSD 17 24 ROFSC REFD 16 20k RCOMD 15 25 REFC POWER-ON RESET 20k 2.56M GEADJD 14 2.56M 20k 20k CONTROL AND READBACK LOGIC RIND 13 26 RCOMC 27 GEADJC 28 RINC 4, 11, 37 32 GND 34 33 31 30 M-SPAN S2 S1 35 S0 RFLAG CLR 5 6 7 36 8 CS/LD SDI SCK LDAC SRO 9 2754 BD SROGND 2754f 11 LTC2754 TIMING DIAGRAMS t1 t2 t3 1 SCK t6 t4 2 31 32 t8 SDI LSB t5 t7 CS/LD t11 LDAC t9 SRO Hi-Z LSB 2754 TD OPERATION Output Ranges The LTC2754 is a quad, current-output, serial-input precision multiplying DAC with selectable output ranges. Ranges can either be programmed in software for maximum flexibility—each of the four DACs can be programmed to any one of six output ranges—or hardwired through pin-strapping. Two unipolar ranges are available (0V to 5V and 0V to 10V), and four bipolar ranges (±2.5V, ±5V, ±10V and –2.5V to 7.5V). These ranges are obtained when an external precision 5V reference is used. When a reference voltage of 2V is used, the ranges become: 0V to 2V, 0V to 4V, ±1V, ±2V, ±4V and –1V to 3V. The output ranges are linearly scaled for other reference voltages. Manual Span Configuration VDD LTC2754-16 VDD DAC A – + ±10V DAC B – + ±10V DAC C – + ±10V DAC D – + ±10V M-SPAN S2 S1 S0 CS/LD SDI SCK 2754 F01 Multiple output ranges are not needed in some applications. To configure the LTC2754 to operate in a single span without additional operational overhead, tie the M-SPAN pin directly to VDD. The active output range for all four DACs is then set via hardware pin strapping of pins S2, S1 and S0 (rather than through the SPI port); and Write and Update commands have no effect on the active output span. See Figure 1 and Table 3. Figure 1. Using M-SPAN to Configure the LTC2754 for Single-Span Operation (±10V Range Shown). Tie the M-SPAN pin to ground for normal SoftSpan operation. 2754f 12 LTC2754 OPERATION Input and DAC Registers The LTC2754 has 5 internal registers for each DAC, a total of 20 registers (see Block Diagram). Each DAC channel has two sets of double-buffered registers—one set for the code data, and one for the output range of the DAC—plus one readback register. Double buffering provides the capability to simultaneously update the span (output range) and code, which allows smooth voltage transitions when changing output ranges. It also permits the simultaneous updating of multiple DACs. Each set of double-buffered registers comprises an Input register and a DAC register. Input register: The Write operation shifts data from the SDI pin into a chosen Input register. The Input registers are holding buffers; Write operations do not affect the DAC outputs. DAC register: The Update operation copies the contents of an Input register to its associated DAC register. The contents of a DAC register directly updates the associated DAC output voltage or output range. Note that updates always include both Data and Span registers; but the values held in the DAC registers will only change if the associated Input register values have previously been changed via a Write operation. Serial Interface When the CS/LD pin is taken low, the data on the SDI pin is loaded into the shift register on the rising edge of the clock (SCK pin). The minimum (24-bit wide) loading sequence required for the LTC2754 is a 4-bit command word (C3 C2 C1 C0), followed by a 4-bit address word (A3 A2 A1 A0) and 16 data (span or code) bits, MSB first. Figure 2 shows the SDI input word syntax to use when writing code or span. If a 32-bit input sequence is used, the first eight bits must be zeros, followed by the same sequence as for a 24-bit wide input. Figure 3 shows the input and readback sequences for both 24-bit and 32-bit operations. When CS/LD is low, the SRO pin (Serial Readback Output) is an active output.The readback data begins after the command (C3-C0) and address (A3-A0) words have been shifted into SDI. SRO outputs a logic low until the readback data begins. For a 24-bit input sequence, the 16 readback bits are shifted out on the falling edges of clocks 8-23, suitable for shifting into a microprocessor on the rising edges of clocks 9-24. For a 32-bit sequence, the bits are shifted out on clocks 16-31; see Figure 3b. When CS/LD is high, the SRO pin presents a high impedance (three-state) output. LDAC is an asynchronous update pin. When LDAC is taken low, all DACs are updated with code and span data (data in the Input buffers is copied into the DAC buffers). CS/LD must be high during this operation; otherwise LDAC is locked out and will have no effect. The use of LDAC is functionally identical to the “Update All DACs” serial input command. The codes for the command word (C3-C0) are defined in Table 1; Table 2 defines the codes for the address word (A3-A0). Readback In addition to the Input and DAC registers, each DAC has one Readback register associated with it. When a Read command is issued to a DAC, the contents of one of its four buffers (Input and DAC registers for each of Span and Code) is copied into its Readback register and serially shifted out through the SRO pin. Figure 3 shows the loading and readback sequences. In the data field (D15-D0) of any non-read instruction cycle, SRO shifts out the contents of the buffer that was specified in the preceding command. This “rolling readback” default mode of operation can dramatically reduce the number of instruction cycles needed, since any command can be verified during succeeding commands with no additional overhead. See Figure 4. Table 1 shows the storage location (‘readback pointer’) of the data which will be output from SRO during the next instruction. For Read commands, the data is shifted out during the Read instruction itself (on the 16 falling SCK edges immediately after the last address bit is shifted in on SDI). When checking the span of a DAC using SRO, the span bits are the last four bits shifted out, corresponding to their sequence and positions when writing a span. See Figure 3. 2754f 13 LTC2754 OPERATION Table 1. Command Codes C3 CODE C2 C1 C0 COMMAND READBACK POINTER– CURRENT INPUT WORD W0 READBACK POINTER– NEXT INPUT WORD W+1 0 0 1 0 Write Span DAC n Set by Previous Command Input Span Register DAC n 0 0 1 1 Write Code DAC n Set by Previous Command Input Code Register DAC n 0 1 0 0 Update DAC n Set by Previous Command DAC Span Register DAC n 0 1 0 1 Update All DACs Set by Previous Command DAC Code Register DAC A 0 1 1 0 Write Span DAC n Update DAC n Set by Previous Command DAC Span Register DAC n 0 1 1 1 Write Code DAC n Update DAC n Set by Previous Command DAC Code Register DAC n 1 0 0 0 Write Span DAC n Update All DACs Set by Previous Command DAC Span Register DAC n 1 0 0 1 Write Code DAC n Update All DACs Set by Previous Command DAC Code Register DAC n 1 0 1 0 Read Input Span Register DAC n Input Span Register DAC n 1 0 1 1 Read Input Code Register DAC n Input Code Register DAC n 1 1 0 0 Read DAC Span Register DAC n DAC Span Register DAC n 1 1 0 1 Read DAC Code Register DAC n 1 1 1 1 No Operation Set by Previous Command DAC Code Register DAC n DAC Code Register DAC n – System Clear – DAC Span Register DAC A – Initial Power-Up or Power Interupt – DAC Span Register DAC A Codes not shown are reserved–do not use Table 2. Address Codes Table 3. Span Codes A3 A2 A1 A0 n S3 S2 S1 S0 0 0 0 × DAC A × 0 0 0 Unipolar 0V to 5V 0 0 1 × DAC B × 0 0 1 Unipolar 0V to 10V 0 1 0 × DAC C × 0 1 0 Bipolar –5V to 5V 0 1 1 × DAC D × 0 1 1 Bipolar –10V to 10V 1 1 1 × All DACs (Note 1) × 1 0 0 Bipolar –2.5V to 2.5V × 1 0 1 Bipolar –2.5V to 7.5V Codes not shown are reserved–do not use. × = Don’t Care. Note 1. If readback is taken using the All DACs address, the LTC2754 defaults to DAC A. SPAN Codes not shown are reserved–do not use. × = Don’t Care. 2754f 14 LTC2754 OPERATION Readback in M-Span Configuration If the part is in M-Span configuration and a DAC Span register is specified for readback, then the data shifted out of SRO will reflect the actual active span. The hardwareconfigured output range is therefore software detectable and available for use in programming. Examples 1. Using a 24-bit instruction, load DAC A with the unipolar range of 0V to 10V, output at zero volts and all other DACs with the bipolar range of ±10V, outputs at zero volts. Note all DAC outputs should change at the same time. a) CS/LD↓ Clock SDI = 0010 1111 0000 0000 0000 0011 b) CS/LD↑ Input register- Range of all DACs set to bipolar ±10V. c) CS/LD↓ Clock SDI = 0010 0000 0000 0000 0000 0001 d) CS/LD↑ Input register- Range of DAC A set to unipolar 0V to 10V. e) CS/LD↓ Clock SDI = 0011 1111 1000 0000 0000 0000 f) CS/LD↑ Input register- Code of all DACs set to midscale. g) CS/LD↓ Clock SDI = 0011 0000 0000 0000 0000 0000 h) CS/LD↑ Input register- Code of DAC A set to zero code. i) CS/LD↓ Clock SDI = 0100 1111 XXXX XXXX XXXX XXXX j) CS/LD↑ Update all DACs for both Code and Range. 2. Using a 32-bit load sequence, load DAC C with bipolar ±2.5V and its output at zero volts. Use readback to check Input register contents before updating the DAC output (i.e., before copying Input register contents into DAC register). a) CS/LD↓ (Note that after power-on, the code in Input register is zero) Clock SDI = 0000 0000 0011 0100 1000 0000 0000 0000 b) CS/LD↑ Input register- Code of DAC C set to midscale setting. c) CS/LD↓ Clock SDI = 0000 0000 0010 0100 0000 0000 0000 0100 Data out on SRO = 1000 0000 0000 0000 Verifies that Input register- Code DAC C is at midscale setting. d) CS/LD↑ Input register- Range of DAC C set to Bipolar ±2.5V range. e) CS/LD↓ Clock SDI = 0000 0000 1010 0100 xxxx xxxx xxxx xxxx Data Out on SRO = 0000 0000 0000 0100 Verifies that Input register- range of DAC C set to Bipolar ±2.5V Range. CS/LD↑ f) CS/LD↓ Clock SDI = 0000 0000 0100 0100 xxxx xxxx xxxx xxxx g) CS/LD↑ Update DAC C for both Code and Range h) Alternatively steps f and g could be replaced with LDAC . k) Alternatively steps i and j could be replaced with LDAC . 2754f 15 LTC2754 OPERATION System Offset and Reference Adjustments The LTC2754 has individual offset- and gain- adjust pins (VOSADJX and GEADJX, respectively) for each of its four DACs. Many systems require compensation for overall system offset. This may be an order of magnitude or more greater than the offset of the LTC2754, which is so low as to be dominated by external output amplifier errors even when using the most precise op amps. The offset adjust pins VOSADJX can be used to null unipolar offset or bipolar zero error. The offset-voltage delta is inverted and attenuated such that a 5V control voltage applied to VOSADJX produces ΔVOS = –512 LSB (LTC2754-16) in any output range (assumes a 5V reference voltage at RINX). In voltage terms, the offset delta is attenuated by a factor of 32, 64 or 128, depending on the output range. (These functions hold regardless of reference voltage.) ΔVOS = –(1/128)VOSADJX [0V to 5V, ±2.5V spans] ΔVOS = –(1/64)VOSADJX [0V to 10V, ±5V, –2.5V to 7.5V spans] ΔVOS = –(1/32)VOSADJX [±10V span] The gain error adjust pins GEADJX can be used to null gain error or to compensate for reference errors. Nominal adjustment range is ±512 LSB (LTC2754-16) for a voltage input range of ±VRINX (i.e., ±5V for a 5V reference input). The gain-error delta is non-inverting for positive reference voltages. Note that these pins compensate the gain by altering the inverted reference voltage VREFX. In voltage terms, the VREFX delta is inverted and attenuated by a factor of 128. ΔVREFX = –(1/128)GEADJX The nominal input range of these pins is ±5V; other voltages of up to ±15V may be used if needed. However, do not use voltages divided down from power supplies; reference-quality, low-noise inputs are required to maintain the performance of which the part is capable. The VOSADJX pins have an input impedance of 1.28MΩ. These pins should be driven with a Thevenin-equivalent impedance of 10k or less to preserve the settling performance of the LTC2754. They should be shorted to GND if not used. The GEADJX pins have an input impedance of 2.56MΩ, and are intended for use with fixed reference voltages only. They should be shorted to GND if not used. If the reference inverting resistors are not used for that channel, then GEADJX, RCOMX and RINX should all be shorted to REFX. Power-On Reset and Clear When power is first applied to the LTC2754, all DACs power-up in unipolar 5V mode (S3 S2 S1 S0 = 0000). All internal DAC registers are reset to 0 and the DAC outputs initialize to zero volts. If the part is configured for manual span operation, all four DACs will be set into the pin-strapped range at the first Update command. This allows the user to simultaneously update span and code for a smooth voltage transition into the chosen output range. When the CLR pin is taken low, a system clear results. The DAC buffers are reset to 0 and the DAC outputs are all reset to zero volts. The Input buffers are left intact, so that any subsequent Update command (including the use of LDAC) restores the addressed DACs to their respective previous states. If CLR is asserted during an instruction, i.e., when CS/LD is low, the instruction is aborted. Integrity of the relevant Input buffers is not guaranteed under these conditions, therefore the contents should be checked using readback or replaced. The RFLAG pin is used as a flag to notify the system of a loss of data integrity. The RFLAG output is asserted low at power-up, system clear, or if the supply VDD dips below approximately 2V; and stays asserted until any valid Update command is executed. 2754f 16 SDI C3 C3 C3 LTC2754-16 (WRITE CODE) LTC2754-12 (WRITE CODE) LTC2754-16 LTC2754-12 (WRITE SPAN) C1 C1 C1 CONTROL WORD C2 CONTROL WORD C2 CONTROL WORD C2 C0 C0 C0 A3 A3 A3 A1 A1 A1 A0 A0 A0 0 D11 MSB D15 MSB 0 D10 D14 0 D9 D13 0 D8 D12 0 D7 D11 D5 D9 0 12 ZEROS 0 12-BIT CODE D6 D10 Figure 2. Serial Input Write Sequence ADDRESS WORD A2 ADDRESS WORD A2 ADDRESS WORD A2 D7 0 D4 0 D3 16-BIT CODE D8 0 D2 D6 0 D1 D5 0 D0 LSB D4 S3 0 D3 0 D1 S1 SPAN S2 4 ZEROS 0 D2 S0 0 D0 LSB 2754 F02 LTC2754 OPERATION 2754f 17 18 READBACK SPAN 0 0 0 0 0 2 0 Hi-Z 0 1 READBACK CODE Hi-Z SRO 0 0 SRO SDI SCK CS/LD 3 SRO SRO Hi-Z C2 0 0 0 0 0 0 0 0 8 ZEROS 0 4 5 0 0 0 6 READBACK SPAN Hi-Z READBACK CODE 0 C3 SDI 2 C1 3 0 0 0 7 0 0 4 0 8 0 0 C0 0 0 CONTROL WORD 1 SCK CS/LD 0 0 C3 A1 7 C2 10 0 0 C1 11 0 0 0 0 0 0 8 0 0 0 D15 D15 9 0 D14 D14 10 0 D13 D13 11 0 D12 D12 12 0 D11 D11 13 0 D10 D10 14 D8 16 0 D9 0 D8 A1 15 0 0 0 0 ADDRESS WORD A2 14 0 0 A0 16 0 D15 D15 17 0 D14 D14 18 SRO SDI SCK 0 D13 D13 19 0 D12 D12 20 21 0 D7 D15 D15 t1 0 D11 D11 Figure 3b. 32-Bit Instruction Sequence 0 0 A3 13 32-BIT DATA STREAM D7 17 D6 18 t3 17 0 D10 D10 t2 22 0 D6 DAC CODE OR DAC SPAN D9 15 Figure 3a. 24-Bit Instruction Sequence 12 0 0 A0 C0 ADDRESS WORD A2 6 CONTROL WORD 9 0 0 A3 5 24-BIT DATA STREAM D8 24 0 D4 D4 20 D7 25 S3 D3 D3 21 t9 0 t4 D9 D14 D14 0 D8 18 0 D7 22 D6 26 0 D6 23 S1 D1 D1 0 D5 D5 27 SPAN S2 D2 D2 DAC CODE OR DAC SPAN D9 23 0 D5 D5 19 0 D4 D4 28 S0 D0 D0 24 S3 D3 D3 29 30 31 S1 D1 D1 SPAN S2 D2 D2 2754 F03 S0 D0 D0 32 2754 F04 LTC2754 OPERATION 2754f LTC2754 OPERATION SDI WRITE DATA DAC A WRITE DATA DAC B WRITE DATA DAC C WRITE DATA DAC D UPDATE ALL DACs ... SRO ... READ INPUT DATA REGISTER DAC A READ INPUT DATA REGISTER DAC B READ INPUT DATA REGISTER DAC C READ INPUT DATA REGISTER DAC D READ DAC DATA REGISTER DAC A 2754 F04 Figure 4. Rolling Readback 2754f 19 LTC2754 APPLICATIONS INFORMATION Op Amp Selection in 16-bit LSBs. Divide these results by 16 to obtain the correct LSB sizing. Because of the extremely high accuracy of the 16-bit LTC2754-16, careful thought should be given to op amp selection in order to achieve the exceptional performance of which the part is capable. Fortunately, the sensitivity of INL and DNL to op amp offset has been greatly reduced compared to previous generations of multiplying DACs. Table 6 contains a partial list of LTC precision op amps recommended for use with the LTC2754. The easy-to-use design equations simplify the selection of op amps to meet Table 4. Coefficients for the Equations in Table 5 Tables 4 and 5 contain equations for evaluating the effects of op amp parameters on the LTC2754’s accuracy when programmed in a unipolar or bipolar output range. These are the changes the op amp can cause to the INL, DNL, unipolar offset, unipolar gain error, bipolar zero and bipolar gain error. Tables 4 and 5 can also be used to determine the effects of op amp parameters on the LTC2754-12. However, the results obtained from Tables 4 and 5 are OUTPUT RANGE A1 A2 A3 5V 1.1 2 1 A4 A5 1 10V 2.2 3 0.5 1.5 ±5V 2 2 1 1 1.5 ±10V 4 4 0.83 1 2.5 ±2.5V 1 1 1.4 1 1 –2.5V to 7.5V 1.9 3 0.7 0.5 1.5 Table 5. Easy-to-Use Equations Determine Op Amp Effects on DAC Accuracy in All Output Ranges (Circuit of Page 1). Subscript 1 Refers to Output Amp, Subscript 2 Refers to Reference Inverting Amp. OP AMP INL (LSB) DNL (LSB) BIPOLAR ZERO ERROR (LSB) UNIPOLAR OFFSET (LSB) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) VOS2 (mV) 0 0 0 IB2 (mV) 0 0 0 AVOL2 (V/V) 0 0 0 ( ) ( ) 5V 5V 5V VOS1 • 0.82 • V A3 • VOS1 • 13.2 • V VOS1 • 3.2 • V REF REF REF 5V 5V 5V IB1 (nA) IB1 • 0.0003 • V IB1 • 0.00008 • V IB1 • 0.13 • V REF REF REF 16.5k 1.5k AVOL1 (V/V) A1 • A A2 • A 0 VOL1 VOL1 5V A3 • VOS1 • 19.8 • V REF 5V IB1 • 0.13 • V REF A4 • VOS2 • 13.1 • VOS1 (mV) 0 ( (V5V ) ) 5V A4 • (I • 0.13 • ( V )) A4 • ( 66k ) A B2 REF REF VOL2 UNIPOLAR GAIN ERROR (LSB) 5V VOS1 • 13.2 • V REF 5V IB1 • 0.0018 • V REF 131k A5 • AVOL1 5V VOS2 • 26.2 • VREF 5V IB2 • 0.26 • VREF 131k AVOL2 ( ) ( ) ( ) ( ) ( ) ( ) BIPOLAR GAIN ERROR (LSB) 5V VOS1 • 13.2 • V REF 5V IB1 • 0.0018 • V REF 131k A5 • AVOL1 5V VOS2 • 26.2 • VREF 5V IB2 • 0.26 • VREF 131k AVOL2 ( ) ( ) ( ) ( ) ( ) ( ) Table 6. Partial List of LTC Precision Amplifiers Recommended for Use with the LTC2754 with Relevant Specifications AMPLIFIER SPECIFICATIONS IB nA A VOL V/mV VOLTAGE NOISE nV/√Hz CURRENT NOISE pA/√Hz SLEW RATE V/μs GAIN BANDWIDTH PRODUCT MHz tSETTLING with LTC2755 μs POWER DISSIPATION mW AMPLIFIER VOS μV LT1001 25 2 800 10 0.12 0.25 0.8 120 46 LT1097 50 0.35 1000 14 0.008 0.2 0.7 120 11 LT1112 (Dual) 60 0.25 1500 14 0.008 0.16 0.75 115 10.5/Op Amp LT1124 (Dual) 70 20 4000 2.7 0.3 4.5 12.5 19 69/Op Amp LT1468 75 10 5000 5 0.6 22 90 2 117 LT1469 (Dual) 125 10 2000 5 0.6 22 90 2 123/Op Amp 2754f 20 LTC2754 APPLICATIONS INFORMATION the system’s specified error budget. Select the amplifier from Table 6 and insert the specified op amp parameters in Table 5. Add up all the errors for each category to determine the effect the op amp has on the accuracy of the part. Arithmetic summation gives an (unlikely) worst-case effect. A root-sum-square (RMS) summation produces a more realistic estimate. Op amp offset will contribute mostly to output offset and gain error, and has minimal effect on INL and DNL. For example, for the LTC2754-16 with a 5V reference in 5V unipolar mode, a 250μV op amp offset will cause a 3.3LSB zero-scale error and a 3.3LSB gain error; but only 0.8LSB of INL degradation and 0.2LSB of DNL degradation. While not directly addressed by the simple equations in Tables 4 and 5, temperature effects can be handled just as easily for unipolar and bipolar applications. First, consult an op amp’s data sheet to find the worst-case VOS and IB over temperature. Then, plug these numbers into the VOS and IB equations from Table 5 and calculate the temperature-induced effects. For applications where fast settling time is important, Application Note 74, “Component and Measurement Advances Ensure 16-Bit DAC Settling Time,” offers a thorough discussion of 16-bit DAC settling time and op amp selection. Precision Voltage Reference Considerations Much in the same way selecting an operational amplifier for use with the LTC2754 is critical to the performance of the system, selecting a precision voltage reference also requires due diligence. The output voltage of the LTC2754 is directly affected by the voltage reference; thus, any voltage reference error will appear as a DAC output voltage error. There are three primary error sources to consider when selecting a precision voltage reference for 16-bit applications: output voltage initial tolerance, output voltage temperature coefficient and output voltage noise. Initial reference output voltage tolerance, if uncorrected, generates a full-scale error term. Choosing a reference with low output voltage initial tolerance, like the LT1236 (±0.05%), minimizes the gain error caused by the reference; however, a calibration sequence that corrects for system zero- and full-scale error is always recommended. A reference’s output voltage temperature coefficient affects not only the full-scale error, but can also affect the circuit’s apparent INL and DNL performance. If a reference is chosen with a loose output voltage temperature coefficient, then the DAC output voltage along its transfer characteristic will be very dependent on ambient conditions. Minimizing the error due to reference temperature coefficient can be achieved by choosing a precision reference with a low output voltage temperature coefficient and/or tightly controlling the ambient temperature of the circuit to minimize temperature gradients. Table 7. Partial List of LTC Precision References Recommended for Use with the LTC2754 with Relevant Specifications INITIAL TOLERANCE TEMPERATURE DRIFT 0.1Hz to 10Hz NOISE LT1019A-5, LT1019A-10 ±0.05% 5ppm/°C 12μVP-P LT1236A-5, LT1236A-10 ±0.05% 5ppm/°C 3μVP-P LT1460A-5, LT1460A-10 ±0.075% 10ppm/°C 20μVP-P LT1790A-2.5 ±0.05% 10ppm/°C 12μVP-P LTC6652A-2.048 ±0.05% 5ppm/°C 2.1ppmP-P REFERENCE LTC6652A-2.5 2.1ppmP-P LTC6652A-3 2.1ppmP-P LTC6652A-3.3 2.2ppmP-P LTC6652A-4.096 2.3ppmP-P LTC6652A-5 2.8ppmP-P 2754f 21 LTC2754 APPLICATIONS INFORMATION As precision DAC applications move to 16-bit and higher performance, reference output voltage noise may contribute a dominant share of the system’s noise floor. This in turn can degrade system dynamic range and signal-tonoise ratio. Care should be exercised in selecting a voltage reference with as low an output noise voltage as practical for the system resolution desired. Precision voltage references, like the LT1236, produce low output noise in the 0.1Hz to 10Hz region, well below the 16-bit LSB level in 5V or 10V full-scale systems. However, as the circuit bandwidths increase, filtering the output of the reference may be required to minimize output noise. Grounding As with any high resolution converter, clean grounding is important. A low impedance analog ground plane and star grounding techniques should be used. IOUT2X must be tied to the star ground with as low a resistance as possible. When it is not possible to locate star ground close to IOUT2, a low resistance trace should be used to route this pin to star ground. This minimizes the voltage drop from this pin to ground caused by the code-dependent current flowing to ground. When the resistance of this circuit board trace becomes greater than 1Ω, a force/sense amplifier configuration should be used to drive this pin (see Figure 5). This preserves the excellent accuracy (1LSB INL and DNL) of the LTC2754-16. Layout Figures 6, 7, 8, and 9 show the layout for the LTC2754 evaluation board, DC1546. This shows how to route the digital signals around the device without interfering with the reference and output op amps. Complete demo board documentation is available in the DC1546 “Quick Start Guide.” 2754f 22 LTC2754 APPLICATIONS INFORMATION ALTERNATE AMPLIFIER FOR OPTIMUM SETTLING TIME PERFORMANCE 3, 12, 29, 38 + ZETEX BAT54S 2 6 IOUT2 1 3 2 3 LT1001 1000pF LT1468 1 200Ω 2007 + – 6 2 – IOUT2 ZETEX* BAT54S 3 2 3 *SCHOTTKY BARRIER DIODE VREF 5V LTC2754-16 49 RFBA ROFSA 50 RINA 2 + 15pF GEADJA 1 48 IOUT1A 1/2 LT1469 – 1 3 2 RCOMA 52 2 DAC A – 1/2 LT1469 3 IOUT2A 3 + 1 VOUTA 150pF 47 VOSADJA 51 REFA DAC B – + DAC C – + DAC D – + 2754 F05 Figure 5. Optional Circuits for Driving IOUT2 from GND with a Force/Sense Amplifier. 2754f 23 LTC2754 APPLICATIONS INFORMATION 2754 F06 Figure 6. LTC2754 Evaluation Board DC1546. Layer 1, Top Layer (Component Side) 2754 F07 Figure 7. LTC2754 Evaluation Board DC1546. Layer 2, GND Plane 2754f 24 LTC2754 APPLICATIONS INFORMATION 2754 F08 Figure 8. LTC2754 Evaluation Board DC1546. Layer 3, Power Traces 2754 F09 Figure 9. LTC2754 Evaluation Board DC1546. Layer 4, Bottom Layer (Solder Side) 2754f 25 LTC2754 TYPICAL APPLICATION Digitally Controlled Offset and Gain Trim Circuit. Powering VDD from LT1236 Ensures Quiet Supply 150pF – + 6 5 V+ 8 150pF 2 7 3 – + 4 IN 10μF 6 OUT LT1236-5 5 TRIM GND 10μF 10 0.1μF 10k 10k 39 10k 2 41 V– 52 RINB RRCOMB RINA VDD 1 4 V– 5V 2 V+ V+ 8 42 RCOMA REFB 43 44 ROFSB RFBB 51 49 50 ROFSA REFA 27pF RFBA 4 30 31 5 CS1 6 SDI 7 SCK 8 SDO 36 5V CS2 CLR IOUT1A RFLAG IOUT2A 48 6 3 5 – + V VOSADJA SDI SRO IOUT1B LDAC 47 TO LT1991 27pF 45 2 38 3 – + V VOSADJB LTC2754 VCC VOUTA VOUTB VOUTC V LTC2636 OUTD VOUTE VOUTF 10 VOUTG CLR 6 LDAC VOUTH GND 2 3 4 5 12 13 14 15 T0 ADDITIONAL OFFSET ADJUST CIRCUITS T0 ADDITIONAL GAIN ADJUST CIRCUITS 32 35 34 33 IOUT1C M-SPAN IOUT2C S2 S1 VOSADJC IOUT2D VOSADJD 9 1 2 3 M1 150k 450k 450k P1 P3 P9 TO LT1991 27pF 22 6 29 5 – + V+ 8 7 VOUTC 4 LT1469 21 TO LT1991 27pF 19 2 12 3 – + V+ 8 1 VOUTA 4 LT1469 20 V– 1 40 27 14 4 11 37 53 28 9 26 13 15 25 24 23 16 17 18 450k LT1991 50k M9 M3 46 GEADJA GEADJB GEADJC GEADJD GND GND GND GND SROGND RINC RCOMC RIND RCOMD REFC ROFSC RFBC REFD ROFSD RFBD 7 10 VOUTB – S0 IOUT1D V+ 7 V– 16 8 V+ 8 4 0.1μF 1 REF 7 CS/LD 8 SCK 9 SDI VOUTD – SCK 0.1μF 10k 7 4 CS/LD IOUT2B 11 V+ 8 4μF – + OUT 6 450k 150k 2 3 – + V+ 8 REF 5 150pF 150pF 2 3 4 LT1469 4μF 50k 5V TO LT1991s V– – + V+ 8 7 4 LT1469 V– 2754 TA02 4 V– V+ 7 8 9 10 1 2 3 450k LT1991 50k M9 M3 M1 150k 450k 450k P1 P3 P9 4μF – + OUT 6 450k 150k 4μF 50k REF 5 4 V– 2754f 26 LTC2754 PACKAGE DESCRIPTION UKG Package 52-Lead Plastic QFN (7mm × 8mm) (Reference LTC DWG # 05-08-1729 Rev Ø) 7.50 p0.05 6.10 p0.05 5.50 REF (2 SIDES) 0.70 p0.05 6.45 p0.05 6.50 REF 7.10 p0.05 8.50 p0.05 (2 SIDES) 5.41 p0.05 PACKAGE OUTLINE 0.25 p0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 7.00 p 0.10 (2 SIDES) 0.75 p 0.05 0.00 – 0.05 R = 0.115 TYP 5.50 REF (2 SIDES) 51 52 0.40 p 0.10 PIN 1 TOP MARK (SEE NOTE 6) 1 2 PIN 1 NOTCH R = 0.30 TYP OR 0.35 s 45oC CHAMFER 6.45 p0.10 8.00 p 0.10 (2 SIDES) 6.50 REF (2 SIDES) 5.41 p0.10 R = 0.10 TYP TOP VIEW 0.200 REF 0.00 – 0.05 0.75 p 0.05 (UKG52) QFN REV Ø 0306 0.25 p 0.05 0.50 BSC BOTTOM VIEW—EXPOSED PAD SIDE VIEW NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 2754f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LTC2754 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1027 Precision Reference 1ppm/°C Maximum Drift LT1236A-5 Precision Reference 0.05% Maximum Tolerance, 1ppm 0.1Hz to 10Hz Noise LT1468 16-Bit Accurate Op-Amp 90MHz GBW, 22V/μs Slew Rate LT1469 Dual 16-Bit Accurate Op-Amp 90MHz GBW, 22V/μs Slew Rate LTC1588/LTC1589/ LTC1592 Serial 12-/14-/16-Bit IOUT Single DAC Software-Selectable (SoftSpan) Ranges, ±1LSB INL, DNL, 16-Lead SSOP Package LTC1591/LTC1597 Parallel 14-/16-Bit IOUT Single DAC Integrated 4-Quadrant Resistors LTC2704 Serial 12-/14-/16-Bit VOUT Quad DACs Software-Selectable (SoftSpan) Ranges, Integrated Amplifiers, ±1LSB INL LTC2751 Parallel 12-/14-/16-Bit IOUT SoftSpan Single DAC ±1LSB INL, DNL, Software-Selectable (SoftSpan) Ranges, 5mm × 7mm QFN-38 Package LTC2753 Parallel 12-/14-16-Bit IOUT SoftSpan Dual DACs ±1LSB INL, DNL, Software-Selectable (SoftSpan) Ranges, 7mm × 7mm QFN-48 Package LTC2755 Parallel 12-/14-/16-Bit IOUT SoftSpan Quad DACs ±1LSB INL, DNL, Software-Selectable (SoftSpan) Ranges, 9mm × 9mm QFN-64 Package 2754f 28 Linear Technology Corporation LT 0609 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2009