LTC3427 500mA, 1.25MHz Synchronous Step-Up DC/DC Converter in 2mm × 2mm DFN Package U FEATURES DESCRIPTIO ■ The LTC®3427 is the industry’s first high efficiency, fixed frequency, step-up DC/DC converter with true output disconnect in a 6-lead 2mm × 2mm DFN package. Requiring minimal external components, the LTC3427 operates from an input voltage as low as 1.8V. The LTC3427 contains an internal 0.525Ω N-channel MOSFET switch and a 0.575Ω P-channel MOSFET synchronous rectifier, which enables it to supply 200mA at 3.3V from a 2-cell alkaline battery input. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ High Efficiency: Up to 94% 3.3V at 200mA from Two Alkaline Cells 5V at 200mA from a Single Li-Ion Cell Inrush Current Limiting and Soft-Start Output Disconnect in Shutdown 1.8V to 5V VIN Range 1.8V to 5.25V VOUT Range 1.25MHz Fixed Frequency, Low Noise PWM Internal Synchronous Rectifier Logic Controlled Shutdown (<1µA) Anti-Ringing Control Minimizes EMI Tiny External Components Short-Circuit Protection Low Profile (0.75mm × 2mm × 2mm) DFN Package The LTC3427 limits inrush current during start-up and provides a soft-start of VOUT. A switching frequency of 1.25MHz minimizes solution footprint by allowing the use of tiny, low profile inductors and ceramic capacitors and produces very low VOUT ripple. The current mode PWM design is internally compensated, reducing external parts count. Anti-ringing control reduces EMI in discontinuous mode operation. The LTC3427 also features low shutdown current of under 1µA and thermal shutdown. U APPLICATIO S ■ ■ ■ ■ ■ ■ Handheld Instruments Digital Cameras Wireless Handsets GPS Receivers Portable Medical Devices MP3 Players , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. U TYPICAL APPLICATIO 2.4V to 3.3V Efficiency 2-Cell Alkaline to 3.3V Synchronous Boost Converter 4.7µH ALKALINE 95 EFFICIENCY 2.2µF VIN SW LTC3427 OFF ON SHDN VOUT 1000k GND VOUT 3.3V 200mA 100 85 80 POWER LOSS 4.7µF FB 90 POWER LOSS (mW) + 2-CELL EFFICIENCY (%) VIN 1.8V TO 3.2V 1000 100 75 604k 70 3427 TA01a 10 100 LOAD CURRENT (mA) 10 1000 3427 TA01b 3427fa 1 LTC3427 W W W AXI U U ABSOLUTE RATI GS U U W PACKAGE/ORDER I FOR ATIO (Note 1) VIN, VOUT Voltages ...................................... – 0.3V to 6V SHDN, FB Voltages ..................................... – 0.3V to 6V SW Voltage DC .......................................................... – 0.3V to 6V Pulsed < 100ns ...................................... – 0.3V to 7V Operating Temperature Range (Notes 2, 5) ............................................ – 40°C to 85°C Storage Temperature Range ................ – 65°C to 125°C VOUT FB SHDN TOP VIEW 6 5 4 1 2 3 SW GND VIN 7 DC PACKAGE 6-LEAD (2mm × 2mm) PLASTIC DFN TJMAX = 125°C, θJA = 60°C/W TO 85°C/W EXPOSED PAD (PIN 7) IS GND, MUST BE SOLDERED TO PCB ORDER PART NUMBER LTC3427EDC DC PART MARKING LBSY Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C. VIN = 2.4V, VOUT = 3.3V unless otherwise specified. PARAMETER CONDITIONS Minimum Start-Up Voltage ILOAD < 1mA Output Voltage Adjust Range Feedback Voltage Feedback Input Current MIN ● ● 1.8 ● 1.215 VFB = 1.24V TYP MAX UNITS 1.6 1.8 V 5.25 V 1.24 1.265 V 1 50 nA Quiescent Current—Shutdown VSHDN = 0V, VOUT = 0V 0.01 1 µA Quiescent Current—Active VFB = 1.5V (Note 3) 350 550 µA NMOS Switch Leakage 0.1 5 µA PMOS Switch Leakage 0.1 5 µA NMOS Switch-On Resistance 0.525 Ω PMOS Switch-On Resistance 0.575 Ω ● NMOS Current Limit Current Limit Delay to Output (Note 4) Maximum Duty Cycle VFB = 1V ● Minimum Duty Cycle VFB = 1.5V ● SHDN Input High mA 40 ● Frequency 500 80 87 Soft-Start Time % 0 0.9 1.25 1.5 1 0.35 VSHDN = 5.5V % MHz V SHDN Input Low SHDN Input Current ns 0.01 2 1 V µA ms 3427fa 2 LTC3427 ELECTRICAL CHARACTERISTICS Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3427E is guaranteed to meet performance specifications from 0°C to 70°C. Specifications over the –40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Current is measured into the VOUT pin since the supply current is bootstrapped to the output. The current will reflect to the input supply by: (VOUT/VIN) • Efficiency. The outputs are not switching. Note 4: Specification is guaranteed by design and not 100% tested in production. Note 5: The LTC3427 includes an overtemperature shutdown that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when the overtemperature shutdown is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. U W TYPICAL PERFOR A CE CHARACTERISTICS 2-Cell Alkaline to 3.3V Efficiency 2-Cell Alkaline to 5V Efficiency Li-Ion to 5V Efficiency 100 95 95 VIN = 3.1V 90 EFFICIENCY (%) 80 VIN = 1.8V 75 70 95 VIN = 4.2V 90 VIN = 2.4V 85 100 90 VIN = 3.6V 85 80 EFFICIENCY (%) 100 EFFICIENCY (%) TA = 25°C unless otherwise specified. VIN = 3.1V 75 70 75 65 65 60 60 55 55 55 50 10 100 LOAD CURRENT (mA) 1000 50 1 10 100 LOAD CURRENT (mA) 1000 Inrush Current Control 10mV/DIV IOUT 40mA TO 100mA SHDN 5V/DIV 3427 G04 VIN = 1.8V VOUT = 3.3V COUT = 4.7µF L = 4.7µH 100µs/DIV 1000 VOUT Ripple, AC Coupled VOUT 100mV/DIV AC COUPLED INDUCTOR CURRENT 100mA/DIV 10 100 LOAD CURRENT (mA) 3427 G03 Load Transient Response VOUT 1V/DIV 500µs/DIV 1 3427 G02 3427 G01 VIN = 2.4V COUT = 22µF L = 4.7µH VIN = 1.8V 70 65 1 VIN = 2.4V 80 60 50 VIN = 3.2V 85 3427 G05 ILOAD 100mA ILOAD 50mA ILOAD 10mA VIN = 2.4V VOUT = 3.3V L = 4.7µH CIN = 2.2µF COUT = 4.7µF 500ns/DIV 3427 G13 3427fa 3 LTC3427 U W TYPICAL PERFOR A CE CHARACTERISTICS FB Voltage vs Temperature Current Limit 0.90 TA = 25°C unless otherwise specified. 1.25 VIN = 2.4V VOUT = 3.3V Efficiency vs VIN 100 VIN = 2.4V VOUT = 3.3V VOUT = 3.3V IOUT = 100mA 90 0.70 80 EFFICIENCY (%) FB VOLTAGE (V) CURRENT LIMIT (A) 0.80 1.24 70 60 0.60 VIN > VOUT PMOS LDO MODE 50 0.50 –45 –30 –15 0 15 30 45 60 TEMPERATURE (°C) 75 1.23 –45 –30 –15 90 0 15 30 45 60 TEMPERATURE (°C) 75 40 90 1.5 3.5 VIN (V) 2.5 3427 G07 3427 G06 Frequency Accuracy vs Temperature 4.5 3427 G08 SW Pin Anti-Ringing Operation 1.35 FREQUENCY (MHz) VIN = 2.4V VOUT = 3.3V 1.30 INDUCTOR CURRENT 50mA/DIV 1.25 SW 2V/DIV VIN = 1.8V VOUT = 3.3V COUT = 4.7µF L = 4.7µH 1.20 1.15 –45 –30 –15 0 15 30 45 60 TEMPERATURE (°C) 75 3427 G10 200ns/DIV 90 3427 G09 RDS(ON) vs Temperature VIN Supply Current (No Load) 0.45 0.70 VIN = 2.4V VOUT = 3.3V TA = 25°C VIN = VOUT = VFB VIN SUPPLY CURRENT (mA) 0.65 RDS(ON) (Ω) 0.60 0.40 PMOS 0.55 NMOS 0.50 0.35 0.45 0.40 0.35 –45 –30 –15 0 15 30 45 60 TEMPERATURE (°C) 75 90 3427 G11 0.30 1.5 2.5 3.5 VIN (V) 4.5 5.5 3427 G12 3427fa 4 LTC3427 U U U PI FU CTIO S SW (Pin 1): Switch Pin for the Inductor Connection. Minimize trace length between SW and the inductor. For discontinuous inductor current, an internal 200Ω impedance is connected from SW to VIN to eliminate high frequency ringing, reducing EMI radiation. GND (Pin 2): Signal and Power Ground. Provide a short, direct PCB path between GND and the (–) side of the input and output capacitor(s). FB (Pin 5): Feedback Input to the Error Amplifier. Connect resistor divider tap to this pin. Referring to the Block Diagram, VOUT can be adjusted from 1.8V to 5.25V by: ⎛ R1⎞ VOUT = 1.24V • ⎜ 1+ ⎟ ⎝ R2 ⎠ VIN (Pin 3): Input Supply Voltage. Connect VIN to the input supply and decouple with a 2.2µF or larger ceramic capacitor as close to VIN as possible. VOUT (Pin 6): Output Voltage Sense Input and Drain of the Internal Synchronous Rectifier MOSFET. Driver bias is derived from VOUT. PCB trace length from VOUT to the output filter capacitor(s) should be as short and wide as possible. SHDN (Pin 4): Shutdown Input. Less than 350mV on SHDN shuts down the LTC3427. Placing 1V or more on SHDN enables the LTC3427. Exposed Pad (Pin 7): Ground for the LTC3427. This pin must be soldered to the PCB ground plane for electrical connection and rated thermal performance. W BLOCK DIAGRA L1 4.7µH + CIN 2.2µF 4 3 1 VIN SHDN SW VIN SHUTDOWN AND VBIAS OPTIONAL BULK CONTROL SIGNALS ANTIRING VOUT VOUT 1.8V TO 5.25V 6 SHDN PWM LOGIC AND DRIVERS + – IZERO COMP CURRENT SENSE 1.24V REFERENCE PWM COMP – + – VIN 1.8V TO 5V THERMAL SHUTDOWN ILIM REF Σ 1V GAIN ERROR AMPLIFIER R1 + FB – 1.24V COUT 4.7µF 5 R2 + + SLOPE COMPENSATION START-UP SOFT-START OSCILLATOR 7 EXPOSED PAD GND 2 3427 BD 3427fa 5 LTC3427 U OPERATIO (Refer to Block Diagram) LOW NOISE FIXED FREQUENCY OPERATION of input or output voltage. The current signal is blanked for approximately 25ns to enhance noise rejection. Shutdown The LTC3427 is shut down by pulling the SHDN pin below 0.35V, and activated by pulling the SHDN pin above 1V. Note that SHDN can be driven above VIN or VOUT as long as it is limited to less than the absolute maximum rating. Current Limit The current limit circuitry shuts off the internal N-channel MOSFET switch when the current limit threshold is reached. The current limit comparator delay to output is typically 40ns. Soft-Start The LTC3427 provides soft-start by ramping the peak inductor current from zero to its peak value of 500mA. The soft-start time is typically 2ms. A soft-start cycle is reinitiated in the event of a commanded shutdown or a thermal shutdown. Zero Current Comparator The zero current comparator monitors the inductor current to the output and shuts off the synchronous rectifier once this current reduces to approximately 20mA. Anti-Ringing Control Oscillator The frequency of operation is set by an internal oscillator to 1.25MHz for the LTC3427. Error Amplifier The error amplifier is a transconductance type with its positive input internally connected to the 1.24V reference and the negative input connected to FB. Internal clamps limit the minimum and maximum error amplifier output voltage for improved large-signal transient response. Power converter control loop compensation is provided internally by the error amplifier. A voltage divider from VOUT to ground programs the output voltage via FB from 1.8V to 5.25V. ⎛ R1⎞ VOUT = 1.24V • ⎜ 1+ ⎟ ⎝ R2 ⎠ The anti-ringing control connects a resistor across the inductor to damp the ringing on the SW pin in discontinuous conduction mode. The LCSW ringing (L = Inductor, CSW = capacitance on the SW pin) is low energy, but can cause EMI radiation. Output Disconnect and Inrush Limiting The LTC3427 provides true output disconnect by eliminating body diode conduction of the internal P-channel MOSFET rectifier. This allows VOUT to go to zero volts during shutdown without drawing any current from the input source. It also provides inrush current limiting at turn-on, minimizing surge currents seen by the input supply. Note that to obtain the advantages of output disconnect, there must not be any external Schottky diode connected between SW and VOUT. Thermal Shutdown The error amplifier also provides a soft-start feature internal to the device. Current Sensing Lossless current sensing converts the peak current signal of the N-channel MOSFET switch into a voltage that is summed with the internal slope compensation. The summed signal is compared to the error amplifier output to provide a peak current control command for the PWM. Peak switch current is limited to 500mA minimum, independent If the die temperature reaches approximately 145°C, the part will go into thermal shutdown. All switches will be turned off. The device will be enabled and initiate a softstart sequence when the die temperature drops by approximately 10°C. Note: Due to the high frequency operation of the LTC3427, board layout is extremely critical to minimize transients due to stray inductance. Keep the output filter capacitor as close as possible to the VOUT pin and use very low ESR/ ESL ceramic capacitors tied to a good ground plane. 3427fa 6 LTC3427 U W U U APPLICATIO S I FOR ATIO LTC3427 SW 1 6 VOUT GND 2 + 5 FB VIN 3 MINIMIZE TRACE ON FB 4 SHDN VIN MULTIPLE VIAS TO GROUND PLANE 3427 F01 Figure 1. Recommended Component Placement for a Single Layer Board. Traces Carrying High Current are Direct (GND, SW, VIN, VOUT). Trace Area at FB is Kept Low. Lead Length to Battery Should be Kept Short. VIN and VOUT Ceramic Capacitors Should be as Close to the LTC3427 as Possible. A Multilayer Board with a Separate Ground Plane is Ideal, but not Absolutely Necessary COMPONENT SELECTION Inductor Selection The LTC3427 can utilize small surface mount and chip inductors due to its fast 1.25MHz switching frequency. A minimum inductance value of 3.3µH is necessary for 3.6V and lower voltage applications and a 4.7µH for output voltages greater than 3.6V. Larger values of inductance will allow greater output current capability by reducing the inductor ripple current. Increasing the inductance above 10µH will increase size while providing little improvement in output current capability. The approximate output current capability of the LTC3427 vs Inductance value is given below in Equation 1 and illustrated graphically in Figure 2. V •D ⎞ ⎛ IOUT(MAX ) = n • ⎜ IP – IN ⎟ • (1 – D) ⎝ f • L • 2⎠ where: n = estimated efficiency IP = peak current limit value (0.5A min) VIN = input (battery) voltage D = steady-state duty ratio = (VOUT – VIN)/VOUT f = switching frequency (1.25MHz typical) L = inductance value (1) The inductor current ripple is typically set for 20% to 40% of the maximum inductor current (IP). High frequency ferrite core inductor materials reduce frequency dependent power losses compared to cheaper powdered iron types, improving efficiency. The inductor should have low ESR (series resistance of the windings) to reduce the I2R power losses, and must be able to handle the peak inductor current without saturating. Molded chokes and some chip inductors usually do not have enough core to support the peak inductor currents of greater than 500mA seen on the LTC3427. To minimize radiated noise, use a toroid, pot core or shielded bobbin inductor. See Table 1 for suggested suppliers. Output and Input Capacitor Selection Low ESR (equivalent series resistance) capacitors should be used to minimize the output voltage ripple. Multilayer ceramic capacitors are an excellent choice as they have extremely low ESR and are available in small footprints. A 2.2µF to 10µF output capacitor is sufficient for most applications. Larger values up to 22µF may be used to obtain extremely low output voltage ripple and improve transient response. An additional phase lead capacitor may be required with output capacitors larger than 10µF to maintain acceptable phase margin. X5R and X7R dielectric materials are preferred for their ability to maintain capacitance over wide voltage and temperature ranges. 3427fa 7 LTC3427 U W U U APPLICATIO S I FOR ATIO Table 1. Inductor Vendor Information SUPPLIER PHONE FAX WEBSITE Murata USA: (814) 237-1431 (800) 831-9172 USA: (814) 238-0490 www.murata.com Sumida USA: (847) 956-0666 Japan: 81-3-3607-5111 USA: (847) 956-0702 Japan: 81-3-3607-5144 www.sumida.com Coilcraft (847) 639-6400 (847) 639-1469 www.coilcraft.com CoEv Magnetics (800) 227-7040 (650) 361-2508 www.circuitprotection.com/magnetics.asp TDK (847) 803-6100 (847) 803-6296 www.component.tdk.com TOKO (847) 297-0070 (847) 669-7864 www.toko.com Wurth (201) 785-8800 (201) 785-8810 www.we-online.com 0.280 Table 2. Capacitor Vendor Information 1.8V TO 3V 0.260 3.1V TO 5V OUTPUT CURRENT (A) 0.240 1.8V TO 3.3V 0.220 SUPPLIER PHONE FAX WEBSITE AVX (803) 448-9411 (803) 448-1943 www.avxcorp.com Sanyo (619) 661-6322 (619) 661-1055 www.sanyovideo.com TDK (847) 803-6100 (847) 803-629 www.component. tdk.com Murata USA: (814) 237-1431 (800) 831-9172 USA: (814) 238-0490 www.murata.com Taiyo Yuden (408) 573-4150 (408) 573-4159 www.t-yuden.com 1.8V TO 3.6V 0.200 0.180 0.160 1.8V TO 5V 0.140 0.120 0.100 3 5 7 9 11 13 15 17 19 21 23 INDUCTANCE (µH) 3427 F02 Figure 2. Maximum Output Current vs Inductance Based on 90% Efficiency Low ESR input capacitors reduce input switching noise and reduce the peak current drawn from the battery. It follows that ceramic capacitors are also a good choice for input decoupling and should be located as close as possible to the device. A 2.2µF input capacitor is sufficient for virtually any application. Larger values may be used without limitations. Table 2 shows a list of several ceramic capacitor manufacturers. Consult the manufacturers directly for detailed information on their entire selection of ceramic capacitors. Thermal Considerations To deliver the power that the LTC3427 is capable of, it is imperative that a good thermal path be provided to dissipate the heat generated within the package. This can be accomplished by taking advantage of the large thermal pad on the underside of the LTC3427. It is recommended that multiple vias in the printed circuit board be used to conduct heat away from the LTC3427 and into the copper plane with as much area as possible. In the event that the junction temperature gets too high, the LTC3427 will go into thermal shutdown and all switching will stop until the internal temperature drops at which point a soft-start cycle will be initiated. 3427fa 8 LTC3427 U W U U APPLICATIO S I FOR ATIO VIN > VOUT Operation Short-Circuit Protection The LTC3427 will maintain voltage regulation when the input voltage is above the output voltage. This is achieved by terminating the switching of the synchronous P-channel MOSFET and applying VIN statically on its gate. This will ensure the volt • seconds across the inductor reverse during the time current is flowing to the output. Since this mode will dissipate more power in the LTC3427, the maximum output current is limited in order to maintain an acceptable junction temperature and is given by: The LTC3427 output disconnect feature allows output short circuit while maintaining a maximum internally set current limit. However, the LTC3427 also incorporates internal features such as current limit foldback and thermal shutdown for protection from an excessive overload or short circuit. During a prolonged short circuit the current limit folds back to a typical value of approximately 400mA should VOUT drop below 950mV. This 400mA current limit remains in effect until VOUT exceeds approximately 1V, at which time the nominally internally set current limit is restored. IOUT(MAX ) = 125 – TA 85 • ⎡⎣( VIN + 1.5) – VOUT ⎤⎦ where TA = ambient temperature. For example at VIN = 4.5V, VOUT = 3.3V, and TA = 85°C, the maximum output current is 145mA. 3427fa 9 LTC3427 U TYPICAL APPLICATIO S L1 4.7µH 2-CELL ALKALINE + 2-Cell to 3.3V Efficiency 100 CIN 2.2µF 95 VIN LTC3427 OFF ON SHDN VOUT 1000k VOUT 3.3V 200mA COUT 4.7µF FB GND VIN = 3.1V 90 SW EFFICIENCY (%) VIN 1.8V TO 3.2V 604k VIN = 2.4V 85 80 VIN = 1.8V 75 70 65 60 CIN: TAIYO YUDEN X5R JMK212BJ225MD COUT: TAIYO YUDEN X5R JMK212BJ475MD L1: TDK RLF7030T-4R7M3R4 3427 F03a 55 50 10 100 LOAD CURRENT (mA) 1 Figure 3. 2-Cell Alkaline to 3.3V Synchronous Boost Converter 1000 3427 G01 2-Cell to 5V Efficiency L1 4.7µH 2-CELL ALKALINE + 100 95 CIN 2.2µF VIN 90 SW LTC3427 OFF ON SHDN VOUT 5V 150mA VOUT 1000k GND COUT 4.7µF FB EFFICIENCY (%) VIN 1.8V TO 3.2V VIN = 3.2V 85 VIN = 2.4V 80 75 VIN = 1.8V 70 65 332k 60 CIN: TAIYO YUDEN X5R JMK212BJ225MD COUT: TAIYO YUDEN X5R JMK212BJ475MD L1: TDK RLF7030T-4R7M3R4 55 3427 F04a 50 10 100 LOAD CURRENT (mA) 1 Figure 4. 2-Cell Alkaline to 5V Synchronous Boost Converter with Output Disconnect 3427 G03 Li-Ion to 5V Synchronous Boost Converter Li-Ion to 5V Efficiency 100 L1 4.7µH Li-Ion + 95 VIN SW LTC3427 OFF ON SHDN VOUT 5V 250mA VOUT 1000k CIN: TAIYO YUDEN X5R JMK212BJ225MD COUT: TAIYO YUDEN X5R JMK212BJ475MD L1: TDK RLF7030T-4R7M3R4 VIN = 4.2V 90 CIN 2.2µF GND COUT 4.7µF FB 332k EFFICIENCY (%) VIN 3.1V TO 4.2V 1000 VIN = 3.6V 85 80 VIN = 3.1V 75 70 65 60 55 3427 TA02a 50 1 10 100 LOAD CURRENT (mA) 1000 3427 G02 3427fa 10 LTC3427 U PACKAGE DESCRIPTIO DC Package 6-Lead Plastic DFN (2mm × 2mm) (Reference LTC DWG # 05-08-1703) 0.675 ±0.05 2.50 ±0.05 1.15 ±0.05 0.61 ±0.05 (2 SIDES) PACKAGE OUTLINE 0.25 ± 0.05 0.50 BSC 1.42 ±0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS R = 0.115 TYP 0.56 ± 0.05 (2 SIDES) 0.38 ± 0.05 4 6 2.00 ±0.10 (4 SIDES) PIN 1 BAR TOP MARK (SEE NOTE 6) PIN 1 CHAMFER OF EXPOSED PAD 3 0.200 REF 0.75 ±0.05 1 (DC6) DFN 1103 0.25 ± 0.05 0.50 BSC 1.37 ±0.05 (2 SIDES) 0.00 – 0.05 BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WCCD-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3427fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LTC3427 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT®1613 800mA ISW, 1.4MHz, Step-Up DC/DC Converter VIN: 1.1V to 10V, VOUT(MAX) = 34V, IQ = 3mA, ISD < 1µA, 5-Lead SOT-23 Package LT1615 350mA ISW, Micropower, Step-Up DC/DC Converter VIN: 1.2V to 15V, VOUT(MAX) = 34V, IQ = 20µA, ISD < 1µA, ThinSOTTM Package LT1618 1.5A ISW, 1.4MHz, Constant Current/Constant Voltage Step-Up DC/DC Converter VIN: 1.6V to 18V, VOUT(MAX) = 35V, IQ = 1.8mA, ISD < 1µA, DFN, MSOP Packages LT1930/LT1930A 1A ISW, 1.2MHz/2.2MHZ, Step-Up DC/DC Converters VIN: 2.6V to 16V, VOUT(MAX) = 34V, IQ = 4.2mA/5.5mA, ISD < 1µA, ThinSOT Package LTC3400/LTC3400B 600mA ISW, 1.2MHz, Synchronous Step-Up DC/DC Converters 92% Efficiency VIN: 0.85V to 5V, VOUT(MAX) = 5V, IQ = 19µA/300µA, ISD < 1µA, ThinSOT Package LTC3401 1A ISW, 3MHz, Synchronous Step-Up DC/DC Converter 97% Efficiency VIN: 0.5V to 5V, VOUT(MAX) = 6V, IQ = 38µA, ISD < 1µA, 10-Lead MS Package LTC3402 2A ISW, 3MHz, Synchronous Step-Up DC/DC Converter 97% Efficiency VIN: 0.5V to 5V, VOUT(MAX) = 6V, IQ = 38µA, ISD < 1µA, 10-Lead MS Package LTC3421 3A ISW, 3MHz, Synchronous Step-Up DC/DC Converter with Output Disconnect 95% Efficiency VIN: 0.5V to 4.5V, VOUT(MAX) = 5.25V, IQ = 12µA, ISD < 1µA, QFN24 Package LTC3422 1.5A ISW, 3MHz Synchronous Step-Up DC/DC Converter with Output Disconnect 95% Efficiency VIN: 0.5V to 4.5V, VOUT(MAX) = 5.25V, IQ = 25µA, ISD < 1µA, 3mm × 3mm DFN Package LTC3423/LTC3424 1A/2A ISW, 3MHz, Synchronous Step-Up DC/DC Converter 95% Efficiency VIN: 0.5V to 5.5V, VOUT(MAX) = 5.5V, IQ = 38µA, ISD < 1µA, 10-Lead MS Package LTC3426 2A ISW, 1.2MHz, Step-Up DC/DC Converter 92% Efficiency VIN: 1.6V to 4.3V, VOUT(MAX) = 5V, ISD < 1µA, SOT-23 Package LTC3428 500mA ISW, 1.25MHz/2.5MHz, Synchronous Step-Up DC/DC Converters with Output Disconnect 92% Efficiency VIN: 1.8V to 5V, VOUT(MAX) = 5.25V, ISD < 1µA, 2mm × 2mm DFN Package LTC3429 600mA ISW, 500kHz, Synchronous Step-Up DC/DC Converter with Output Disconnect and Soft-Start 96% Efficiency VIN: 0.5V to 4.4V, VOUT(MAX) = 5V, IQ = 20µA/300µA, ISD < 1µA, ThinSOT Package LTC3458 1.4A ISW, 1.5MHz, Synchronous Step-Up DC/DC Converter/Output Disconnect/Burst Mode Operation 93% Efficiency VIN: 1.5V to 6V, VOUT(MAX) = 7.5V, IQ = 15µA, ISD < 1µA, DFN12 Package LTC3458L 1.7A ISW, 1.5MHz, Synchronous Step-Up DC/DC Converter with Output Disconnect, Automatic Burst Mode® Operation 94% Efficiency VOUT(MAX) = 6V, IQ = 12µA, DFN12 Package LTC3459 70mA ISW, 10V Micropower Synchronous Boost Converter/Output Disconnect/Burst Mode Operation VIN: 1.5V to 5.5V, VOUT(MAX) = 10V, IQ = 10µA, ISD < 1µA, ThinSOT Package LTC3525-3.3 LTC3525-5 400mA Micropower Synchronous Step-Up DC/DC Converter with Output Disconnect 95% Efficiency VIN: 1V to 4.5V, VOUT(MAX) = 3.3V or 5V, IQ = 7µA, ISD < 1µA, SC-70 Package ThinSOT is a trademark of Linear Technology Corporation. Burst Mode is a registered trademark of Linear Technology Corporation. 3427fa 12 Linear Technology Corporation LT 0406 REV A • PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2005