LINER LTC6911HMS-1

LTC6911-1/LTC6911-2
Dual Matched Amplifiers
with Digitally Programmable
Gain in MSOP
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
DESCRIPTIO
The LTC®6911 is a family of low noise digitally programmable gain amplifiers (PGAs) that are easy to use and
occupy very little PC board space. The matched gain of
both channels is adjustable using a 3-bit parallel interface
to select voltage gains of 0, 1, 2, 5, 10, 20, 50 and 100V/
V (LTC6911-1) and 0, 1, 2, 4, 8, 16, 32 and 64V/V
(LTC6911-2). All gains are inverting.
3-Bit Digital Gain Control:
(Inverting Gains of 0, 1, 2, 5, 10, 20, 50
and 100V/V) -1 Option
(Inverting Gains of 0, 1, 2, 4, 8, 16, 32
and 64V/V) -2 Option
Two Matched Programmable Gain Amplifiers
Channel-to-Channel Gain Matching of 0.1dB (Max)
Rail-to-Rail Input Range
Rail-to-Rail Output Swing
Single or Dual Supply: 2.7V to 10.5V Total
11MHz Gain Bandwidth Product
Input Noise: 10nV/√Hz
Total System Dynamic Range to 120dB
Input Offset Voltage: 2mV, Gain of 10
Low Profile 10-Lead MSOP Package
The LTC6911 family consists of two matched inverting
amplifiers with rail-to-rail outputs. When operated with
unity gain, they will also process rail-to-rail input signals.
A half-supply reference generated internally at the AGND
pin supports single power supply applications. Operating
from single or split supplies from 2.7V to 10.5V, the
LTC6911 family is offered in a 10-lead MSOP package.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
APPLICATIO S
■
■
Data Acquisition Systems
Dynamic Gain Changing
Automatic Ranging Circuits
Automatic Gain Control
TYPICAL APPLICATIO
V+
2.7V TO 10.5V
0.1µF
Frequency Response (LTC6911-1)
7
DIGITAL
INPUT
GAIN IN V/V
G2 G1 G0 LTC6911-1 LTC6911-2
0 0 0
0
0
0 0 1
–1
–1
0 1 0
–2
–2
0 1 1
–5
–4
1 0 0
–10
–8
1 0 1
–20
–16
1 1 0
–50
–32
1 1 1
–100
–64
50
9
40
VINA
AGND
10
1
VOUTA =
GAIN • VINA
≥1µF
2
LTC6911-X
VS = 10V, VIN = 5mVRMS
GAIN OF –100 (DIGITAL INPUT 111)
30 GAIN OF –50 (DIGITAL INPUT 110)
GAIN (dB)
■
U
■
GAIN OF –20 (DIGITAL INPUT 101)
20
GAIN OF –10 (DIGITAL INPUT 100)
10 GAIN OF –5 (DIGITAL INPUT 011)
VINB
3
8
VOUTB =
GAIN • VINB
691112 TA01
4
G0
5
G1
6
G2
GAIN OF –2 (DIGITAL INPUT 010)
0
GAIN OF –1 (DIGITAL INPUT 001)
–10
100
1k
10k
100k
FREQUENCY (Hz)
1M
10M
691112 TA02
sn691112 691112fs
1
LTC6911-1/LTC6911-2
W W
W
AXI U
U
ABSOLUTE
RATI GS
U
U
W
PACKAGE/ORDER I FOR ATIO
(Note 1)
Total Supply Voltage (V+ to V–) .............................. 11V
Input Current ..................................................... ±10mA
Operating Temperature Range (Note 2)
LTC6911C-1/LTC6911C-2 .................. – 40°C to 85°C
LTC6911I-1/LTC6911I-2 .................... – 40°C to 85°C
LTC6911H-1/LTC6911H-2 ................ – 40°C to 125°C
Specified Temperature Range (Note 3)
LTC6911C-1/LTC6911C-2 .................. – 40°C to 85°C
LTC6911I-1/LTC6911I-2 .................... – 40°C to 85°C
LTC6911H-1/LTC6911H-2 ................ – 40°C to 125°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
TOP VIEW
INA
AGND
INB
G0
G1
10
9
8
7
6
1
2
3
4
5
OUTA
V–
OUTB
V+
G2
MS PACKAGE
10-LEAD PLASTIC MSOP
TJMAX = 150°C, θJA = 230°C/W
ORDER PART NUMBER
MS PART MARKING
LTC6911CMS-1
LTC6911IMS-1
LTC6911HMS-1
LTC6911CMS-2
LTC6911IMS-2
LTC6911HMS-2
LTAHK
LTAHM
LTBCF
LTAHH
LTAHJ
LTBCG
Consult LTC Marketing for parts specified with wider operating temperature ranges.
U
U
U
GAI SETTI GS A D PROPERTIES
Table 1 (LTC6911-1)
G2
0
0
0
0
1
1
1
1
DIGITAL INPUTS
G1
G0
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
NOMINAL
VOLTAGE GAIN
Volts/Volt
(dB)
0
–120
–1
0
–2
6
–5
14
–10
20
–20
26
–50
34
–100
40
MAXIMUM LINEAR INPUT RANGE (VP-P)
Dual 5V
Single 5V
Single 3V
Supply
Supply
Supply
10
5
3
10
5
3
5
2.5
1.5
2
1
0.6
1
0.5
0.3
0.5
0.25
0.15
0.2
0.1
0.06
0.1
0.05
0.03
NOMINAL
INPUT
IMPEDANCE
(kΩ)
(Open)
10
5
2
1
1
1
1
NOMINAL
VOLTAGE GAIN
Volts/Volt
(dB)
0
–120
–1
0
–2
6
–4
12
–8
18.1
–16
24.1
–32
30.1
–64
36.1
MAXIMUM LINEAR INPUT RANGE (VP-P)
Dual 5V
Single 5V
Single 3V
Supply
Supply
Supply
10
5
3
10
5
3
5
2.5
1.5
2.5
1.25
0.75
1.25
0.625
0.375
0.625
0.3125
0.188
0.3125
0.156
0.094
0.156
0.078
0.047
NOMINAL
INPUT
IMPEDANCE
(kΩ)
(Open)
10
5
2.5
1.25
1.25
1.25
1.25
Table 2 (LTC6911-2)
G2
0
0
0
0
1
1
1
1
DIGITAL INPUTS
G1
G0
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
sn691112 691112fs
2
LTC6911-1/LTC6911-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications that apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, AGND = 2.5V, Gain = 1 (Digital Inputs 001), RL = 10k
to midsupply point, unless otherwise noted.
PARAMETER
CONDITIONS
C/I GRADES
MIN TYP MAX
MIN
H GRADE
TYP MAX
UNITS
2.7
2.7
10.5
V
LTC6911-1/LTC6911-2
Total Supply Voltage (VS)
●
10.5
Supply Current per Channel
VS = 2.7V, VINA = VINB = VAGND
VS = 5V, VINA = VINB = VAGND
VS = ±5V, VINA = VINB = 0V, Pins 4, 5, 6 = –4.5V or 5V
VS = ±5V, VINA = VINB = 0V, Pin 4 = 4.5V,
Pins 5, 6 = 0.5V
●
●
●
●
2.1
2.5
3.1
3.1
3.15
3.75
4.65
4.65
2.1
2.5
3.1
3.1
3.25
4.00
5.00
5.00
mA
mA
mA
mA
Output Voltage Swing LOW (Note 4)
VS = 2.7V, RL = 10k Tied to Mid Supply
VS = 2.7V, RL = 500Ω Tied to Mid Supply
●
●
12
60
30
110
12
60
35
125
mV
mV
VS = 5V, RL = 10k Tied to Mid Supply
VS = 5V, RL = 500Ω Tied to Mid Supply
●
●
20
100
40
170
20
100
45
190
mV
mV
VS = ±5V, RL = 10k Tied to 0V
VS = ±5V, RL = 500Ω Tied to 0V
●
●
30
190
50
260
30
190
60
290
mV
mV
VS = 2.7V, RL = 10k Tied to Mid Supply
VS = 2.7V, RL = 500Ω Tied to Mid Supply
●
●
10
50
20
80
10
50
25
90
mV
mV
VS = 5V, RL = 10k Tied to Mid Supply
VS = 5V, RL = 500Ω Tied to Mid Supply
●
●
10
90
30
160
10
90
35
175
mV
mV
VS = ±5V, RL = 10k Tied to 0V
VS = ±5V, RL = 500Ω Tied to 0V
●
●
20
180
40
250
20
180
45
270
mV
mV
Output Short-Circuit Current (Note 5)
VS = 2.7V
VS = ±5V
●
●
±27
±35
AGND Open-Circuit Voltage
VS = 5V
●
2.45
AGND (Common Mode)
Input Voltage Range
VS = 2.7V
VS = 5V
VS = ±5V
●
●
●
0.55
0.75
– 4.30
AGND Rejection (i.e., Common
Mode Rejection or CMRR)
VS = 2.7V, VAGND = 1.1V to 1.6V
VS = ±5V, VAGND = – 2.5V to 2.5V
●
●
55
55
Power Supply Rejection Ratio (PSRR)
VS = 2.7V to ±5V
●
60
Slew Rate
VS = 5V, VOUTA = VOUTB = 1.1V to 3.9V
VS = ±5V, VOUTA = VOUTB = ±1.4V
Signal Attenuation at Gain = 0 Setting
Gain = 0 (Digital Inputs 000), f = 20kHz
●
Digital Input “High” Voltage
VS = 2.7V
VS = 5V
VS = ±5V
●
●
●
Digital Input “Low” Voltage
VS = 2.7V
VS = 5V
VS = ±5V
●
●
●
Digital Input “High” Current
VS = 2.7V, Pins 4, 5, 6 = 2.43V
VS = 5V, Pins 4, 5, 6 = 4.5V
VS = ±5V, Pins 4, 5, 6 = 4.5V
●
●
●
1
5
10
1
5
10
µA
µA
µA
Digital Input “Low” Current
VS = 2.7V, Pins 4, 5, 6 = 0.27V
VS = 5V, Pins 4, 5, 6 = 0.5V
VS = ±5V, Pins 4, 5, 6 = 0.5V
●
●
●
1
5
10
1
5
10
µA
µA
µA
Output Voltage Swing HIGH (Note 4)
2.5
±27
±35
2.55
2.45
1.60
3.65
3.20
0.55
0.75
– 4.30
80
75
50
50
80
57
12
16
– 120
2.5
mA
mA
2.55
V
1.60
3.65
3.20
V
V
V
80
75
dB
dB
80
dB
12
16
V/µs
V/µs
– 120
2.43
4.50
4.50
dB
2.43
4.50
4.50
V
V
V
0.27
0.50
0.50
0.27
0.50
0.50
V
V
V
sn691112 691112fs
3
LTC6911-1/LTC6911-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications that apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, AGND = 2.5V, Gain = 1 (Digital Inputs 001), RL = 10k
to midsupply point, unless otherwise noted.
PARAMETER
CONDITIONS
C/I GRADES
MIN TYP MAX
MIN
H GRADE
TYP MAX
UNITS
LTC6911-1 Only
Voltage Gain (Note 6)
Channel-to-Channel Voltage
Gain Match
VS = 2.7V, Gain = 1, RL = 10k
VS = 2.7V, Gain = 1, RL = 500Ω
●
●
–0.07 0
0.07
–0.11 –0.02 0.07
–0.08 0
0.07
–0.13 –0.02 0.07
dB
dB
VS = 2.7V, Gain = 2, RL = 10k
●
5.94 6.01
5.93
6.08
dB
VS = 2.7V, Gain = 5, RL = 10k
●
13.85 13.95 14.05
13.8 13.95 14.05
dB
VS = 2.7V, Gain = 10, RL = 10k
VS = 2.7V, Gain = 10, RL = 500Ω
●
●
19.7 19.93 20.1
19.6 19.85 20.1
19.65 19.93 20.1
19.45 19.85 20.1
dB
dB
VS = 2.7V, Gain = 20, RL = 10k
●
25.75 25.94 26.1
25.65 25.94 26.1
dB
VS = 2.7V, Gain = 50, RL = 10k
●
33.5 33.8
34.1
33.4
33.8
34.1
dB
VS = 2.7V, Gain = 100, RL = 10k
VS = 2.7V, Gain = 100, RL = 500Ω
●
●
39.0 39.6
37.4 38.9
40.1
40.1
38.8
36.5
39.6
38.9
40.1
40.1
dB
dB
VS = 5V, Gain = 1, RL = 10k
VS = 5V, Gain = 1, RL = 500Ω
●
●
–0.08 0.01 0.08
–0.11 –0.01 0.07
–0.09 0.01 0.08
–0.13 –0.01 0.07
dB
dB
VS = 5V, Gain = 2, RL = 10k
●
5.95 6.02
5.94
6.09
dB
VS = 5V, Gain = 5, RL = 10k
●
13.8 13.96 14.1
13.78 13.96 14.1
dB
VS = 5V, Gain = 10, RL = 10k
VS = 5V, Gain = 10, RL = 500Ω
●
●
19.8 19.94 20.1
19.6 19.87 20.1
19.75 19.94 20.1
19.45 19.87 20.1
dB
dB
VS = 5V, Gain = 20, RL = 10k
●
25.8 25.94 26.1
25.75 25.94 26.1
dB
VS = 5V, Gain = 50, RL = 10k
●
33.5 33.84 34.1
33.4 33.84 34.1
dB
VS = 5V, Gain = 100, RL = 10k
VS = 5V, Gain = 100, RL = 500Ω
●
●
39.3 39.7
38.0 39.2
40.1
40.1
39.1
37.0
39.7
39.2
40.1
40.1
dB
dB
VS = ±5V, Gain = 1, RL = 10k
VS = ±5V, Gain = 1, RL = 500Ω
●
●
–0.06 0.01
–0.10 0.00
0.08
0.08
–0.07 0.01
–0.11 0.00
0.08
0.08
dB
dB
VS = ±5V, Gain = 2, RL = 10k
●
5.95 6.02
6.09
5.94
6.09
dB
VS = ±5V, Gain = 5, RL = 10k
●
13.8 13.96 14.1
13.79 13.96 14.1
dB
VS = ±5V, Gain = 10, RL = 10k
VS = ±5V, Gain = 10, RL = 500Ω
●
●
19.8 19.94 20.1
19.7 19.91 20.1
19.75 19.94 20.1
19.60 19.91 20.1
dB
dB
VS = ±5V, Gain = 20, RL = 10k
●
25.8 25.95 26.1
25.75 25.95 26.1
dB
VS = ±5V, Gain = 50, RL = 10k
●
33.7 33.87 34.1
33.60 33.87 34.1
dB
VS = ±5V, Gain = 100, RL = 10k
VS = ±5V, Gain = 100, RL = 500Ω
●
●
39.4 39.8
38.8 39.5
40.2
40.1
39.25 39.8
38.00 39.5
40.2
40.1
dB
dB
VS = 2.7V, Gain = 1, RL = 10k
VS = 2.7V, Gain = 1, RL = 500Ω
●
●
–0.1 0.02
–0.1 0.02
0.1
0.1
–0.1
–0.1
0.02
0.02
0.1
0.1
dB
dB
VS = 2.7V, Gain = 2, RL = 10k
●
–0.1 0.02
0.1
–0.1
0.02
0.1
dB
VS = 2.7V, Gain = 5, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 2.7V, Gain = 10, RL = 10k
VS = 2.7V, Gain = 10, RL = 500Ω
●
●
–0.15 0.02
–0.15 0.02
0.15
0.15
–0.15 0.02
–0.15 0.02
0.15
0.15
dB
dB
VS = 2.7V, Gain = 20, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 2.7V, Gain = 50, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 2.7V, Gain = 100, RL = 10k
VS = 2.7V, Gain = 100, RL = 500Ω
●
●
–0.20 0.02
–1.00 0.02
0.20
1.00
–0.20 0.02
–1.50 0.02
0.20
1.50
dB
dB
6.08
6.09
6.01
6.02
6.02
sn691112 691112fs
4
LTC6911-1/LTC6911-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications that apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, AGND = 2.5V, Gain = 1 (Digital Inputs 001), RL = 10k
to midsupply point, unless otherwise noted.
PARAMETER
CONDITIONS
C/I GRADES
MIN TYP MAX
MIN
H GRADE
TYP MAX
UNITS
LTC6911-1 Only
Channel-to-Channel Voltage
Gain Match
Gain Temperature Coefficient
VS = 5V, Gain = 1, RL = 10k
VS = 5V, Gain = 1, RL = 500Ω
●
●
–0.1 0.02
–0.1 0.02
0.1
0.1
–0.1
–0.1
0.02
0.02
0.1
0.1
dB
dB
VS = 5V, Gain = 2, RL = 10k
●
–0.1 0.02
0.1
–0.1
0.02
0.1
dB
VS = 5V, Gain = 5, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 5V, Gain = 10, RL = 10k
VS = 5V, Gain = 10, RL = 500Ω
●
●
–0.15 0.02
–0.15 0.02
0.15
0.15
–0.15 0.02
–0.15 0.02
0.15
0.15
dB
dB
VS = 5V, Gain = 20, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 5V, Gain = 50, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 5V, Gain = 100, RL = 10k
VS = 5V, Gain = 100, RL = 500Ω
●
●
–0.2 0.02
–0.8 0.02
0.2
0.8
–0.2
–1.2
0.02
0.02
0.2
1.2
dB
dB
VS = ±5V, Gain = 1, RL = 10k
VS = ±5V, Gain = 1, RL = 500Ω
●
●
–0.1 0.02
–0.1 0.02
0.1
0.1
–0.1
–0.1
0.02
0.02
0.1
0.1
dB
dB
VS = ±5V, Gain = 2, RL = 10k
●
–0.1 0.02
0.1
–0.1
0.02
0.1
dB
VS = ±5V, Gain = 5, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = ±5V, Gain = 10, RL = 10k
VS = ±5V, Gain = 10, RL = 500Ω
●
●
–0.15 0.02
–0.15 0.02
0.15
0.15
–0.15 0.02
–0.15 0.02
0.15
0.15
dB
dB
VS = ±5V, Gain = 20, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = ±5V, Gain = 50, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = ±5V, Gain = 100, RL = 10k
VS = ±5V, Gain = 100, RL = 500Ω
●
●
–0.2 0.02
–0.6 0.02
0.2
0.6
–0.2
–0.9
0.2
0.9
dB
dB
VS = 5V, Gain = 1, RL = Open
VS = 5V, Gain = 2, RL = Open
VS = 5V, Gain = 5, RL = Open
VS = 5V, Gain = 10, RL = Open
VS = 5V, Gain = 20, RL = Open
VS = 5V, Gain = 50, RL = Open
VS = 5V, Gain = 100, RL = Open
Channel-to-Channel Gain Temperature VS = 5V, Gain = 1, RL = Open
Coefficient Match
VS = 5V, Gain = 2, RL = Open
VS = 5V, Gain = 5, RL = Open
VS = 5V, Gain = 10, RL = Open
VS = 5V, Gain = 20, RL = Open
VS = 5V, Gain = 50, RL = Open
VS = 5V, Gain = 100, RL = Open
Channel-to-Channel Isolation (Note 7)
f = 200kHz
VS = 5V, Gain = 1, RL = 10k
VS = 5V, Gain = 10, RL = 10k
VS = 5V, Gain = 100, RL = 10k
Offset Voltage Magnitude Referred
to INA or INB Pins (Note 8)
Gain = 1
Gain = 10
Offset Voltage Magnitude Drift
Referred to INA or INB Pins (Note 8)
Gain = 1
Gain = 10
●
●
0.02
0.02
2
–1.5
–11
–30
–38
–70
–140
2
–1.5
–11
–30
–38
–70
–140
ppm/°C
ppm/°Cppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
1.0
1.0
0.2
1.0
0.4
3.0
3.0
1.0
1.0
0.2
1.0
0.4
3.0
3.0
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
108
107
93
108
107
93
dB
dB
dB
2.0
1.1
12
6.6
22
12
2.0
1.1
20
11
22
14
mV
mV
µV/°C
µV/°C
sn691112 691112fs
5
LTC6911-1/LTC6911-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications that apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, AGND = 2.5V, Gain = 1 (Digital Inputs 001), RL = 10k
to midsupply point, unless otherwise noted.
PARAMETER
C/I GRADES
MIN TYP MAX
CONDITIONS
MIN
H GRADE
TYP MAX
UNITS
LTC6911-1 Only
DC Input Resistance at
INA or INB Pins (Note 9)
DC VINA or VINB = 0V
Gain = 0
Gain = 1
Gain = 2
Gain = 5
Gain > 5
●
●
●
●
●
>100
10
5
2
1
>100
10
5
2
1
DC Input Resistance Match
RINA – RINB
Gain = 1
Gain = 2
Gain = 5
Gain > 5
●
●
●
●
10
5
2
1
10
5
2
1
Ω
Ω
Ω
Ω
DC Small-Signal Output Resistance
at OUTA or OUTB Pins
DC VINA or VINB = 0V
Gain = 0
Gain = 1
Gain = 2
Gain = 5
Gain = 10
Gain = 20
Gain = 50
Gain = 100
0.4
0.7
1.0
1.9
3.4
6.4
15
30
0.4
0.7
1.0
1.9
3.4
6.4
15
30
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Gain-Bandwidth Product
Gain = 100, fIN = 200kHz
Wideband Noise (Referred to Input)
f = 1kHz to 200kHz
Gain = 0 (Output Noise Only)
Gain = 1
Gain = 2
Gain = 5
Gain = 10
Gain = 20
Gain = 50
Gain = 100
7.5
12.3
8.5
6.1
5.2
5.0
4.5
3.8
7.5
12.3
8.5
6.1
5.2
5.0
4.5
3.8
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
Voltage Noise Density
(Referred to Input)
f = 50kHz
Gain = 1
Gain = 2
Gain = 5
Gain = 10
Gain = 20
Gain = 50
Gain = 100
28
19
14
12
11.5
10.8
9.9
28
19
14
12
11.5
10.8
9.9
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
Total Harmonic Distortion
Gain = 10, fIN = 10kHz, VOUT = 1VRMS
– 90
0.003
– 90
0.003
dB
%
Gain = 10, fIN = 100kHz, VOUT = 1VRMS
– 82
0.008
– 82
0.008
dB
%
●
7
11
18
6
11
MΩ
kΩ
kΩ
kΩ
kΩ
18
MHz
sn691112 691112fs
6
LTC6911-1/LTC6911-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications that apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, AGND = 2.5V, Gain = 1 (Digital Inputs 001), RL = 10k
to midsupply point, unless otherwise noted.
PARAMETER
CONDITIONS
C/I GRADES
MIN TYP MAX
MIN
H GRADE
TYP MAX
UNITS
LTC6911-2 Only
Voltage Gain (Note 6)
Channel-to-Channel
Voltage Gain Match
VS = 2.7V, Gain = 1, RL = 10k
VS = 2.7V, Gain = 1, RL = 500Ω
●
●
–0.07 0
0.07
–0.11 –0.02 0.07
–0.08 0
0.07
–0.13 –0.02 0.07
dB
dB
VS = 2.7V, Gain = 2, RL = 10k
●
5.94 6.01
5.93
dB
VS = 2.7V, Gain = 4, RL = 10k
●
11.9 12.02 12.12
11.88 12.02 12.12
dB
VS = 2.7V, Gain = 8, RL = 10k
VS = 2.7V, Gain = 8, RL = 500Ω
●
●
17.80 18.00 18.15
17.65 17.94 18.15
17.75 18.00 18.15
17.55 17.94 18.15
dB
dB
VS = 2.7V, Gain = 16, RL = 10k
●
23.8 24.01 24.25
23.75 24.01 24.25
dB
VS = 2.7V, Gain = 32, RL = 10k
●
29.7
30.2
29.65
30.2
dB
VS = 2.7V, Gain = 64, RL = 10k
VS = 2.7V, Gain = 64, RL = 500Ω
●
●
35.3 35.8
34.2 35.3
36.2
36.2
35.15 35.8
33.65 35.3
36.2
36.2
dB
dB
VS = 5V, Gain = 1, RL = 10k
VS = 5V, Gain = 1, RL = 500Ω
●
●
–0.08 0.00 0.08
–0.10 –0.01 0.08
–0.09 0.00 0.08
–0.12 –0.01 0.08
dB
dB
VS = 5V, Gain = 2, RL = 10k
●
5.96 6.02
5.95
dB
VS = 5V, Gain = 4, RL = 10k
●
11.85 12.02 12.15
11.83 12.02 12.15
dB
VS = 5V, Gain = 8, RL = 10k
VS = 5V, Gain = 8, RL = 500Ω
●
●
17.85 18.01 18.15
17.65 17.96 18.15
17.83 18.01 18.15
17.50 17.96 18.15
dB
dB
VS = 5V, Gain = 16, RL = 10k
●
23.85 24.02 24.15
23.80 24.02 24.15
dB
VS = 5V, Gain = 32, RL = 10k
●
29.70 30.02 30.2
29.65 30.02 30.2
dB
VS = 5V, Gain = 64, RL = 10k
VS = 5V, Gain = 64, RL = 500Ω
●
●
35.5 35.9
34.7 35.6
36.3
36.1
35.40 35.9
34.20 35.6
36.3
36.1
dB
dB
VS = ±5V, Gain = 1, RL = 10k
VS = ±5V, Gain = 1, RL = 500Ω
●
●
–0.06 0.01
–0.10 0.00
0.08
0.08
–0.07 0.01
–0.11 0.00
0.08
0.08
dB
dB
VS = ±5V, Gain = 2, RL = 10k
●
5.96 6.02
6.1
5.95
6.1
dB
VS = ±5V, Gain = 4, RL = 10k
●
11.9 12.03 12.15
11.88 12.03 12.15
dB
VS = ±5V, Gain = 8, RL = 10k
VS = ±5V, Gain = 8, RL = 500Ω
●
●
17.85 18.02 18.15
17.80 17.99 18.15
17.83 18.02 18.15
17.73 17.99 18.15
dB
dB
VS = ±5V, Gain = 16, RL = 10k
●
23.85 24.03 24.15
23.82 24.03 24.15
dB
VS = ±5V, Gain = 32, RL = 10k
●
29.85
30.2
dB
VS = ±5V, Gain = 64, RL = 10k
VS = ±5V, Gain = 64, RL = 500Ω
●
●
35.65 36.0 36.20
35.20 35.8 36.20
35.55 36.0 36.20
34.80 35.8 36.20
dB
dB
VS = 2.7V, Gain = 1, RL = 10k
VS = 2.7V, Gain = 1, RL = 500Ω
●
●
–0.1 0.02
–0.1 0.02
–0.1
–0.1
0.02
0.02
dB
dB
VS = 2.7V, Gain = 2, RL = 10k
●
–0.1 0.02
0.1
–0.1
0.02
0.1
dB
VS = 2.7V, Gain = 4, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 2.7V, Gain = 8, RL = 10k
VS = 2.7V, Gain = 8, RL = 500Ω
●
●
–0.15 0.02
–0.15 0.02
0.15
0.15
–0.15 0.02
–0.15 0.02
0.15
0.15
dB
dB
VS = 2.7V, Gain = 16, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 2.7V, Gain = 32, RL = 10k
●
–0.15 0.02
0.15
–0.15 0.02
0.15
dB
VS = 2.7V, Gain = 64, RL = 10k
VS = 2.7V, Gain = 64, RL = 500Ω
●
●
–0.2 0.02
–0.7 0.02
0.2
0.7
–0.2
–1.0
0.2
1.0
dB
dB
30
30
6.08
6.1
30.2
0.1
0.1
29.8
6.01
30
6.02
6.02
30
0.02
0.02
6.08
6.1
0.1
0.1
sn691112 691112fs
7
LTC6911-1/LTC6911-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications that apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, AGND = 2.5V, Gain = 1 (Digital Inputs 001), RL = 10k
to midsupply point, unless otherwise noted.
PARAMETER
CONDITIONS
C/I GRADES
MIN TYP MAX
MIN
H GRADE
TYP MAX
–0.1
–0.1
–0.1
–0.15
–0.15
–0.15
–0.15
–0.15
–0.15
–0.60
–0.1
–0.1
–0.1
–0.15
–0.15
–0.15
–0.15
–0.15
–0.15
–0.40
–0.1
–0.1
–0.1
–0.15
–0.15
–0.15
–0.15
–0.15
–0.15
–0.80
–0.1
–0.1
–0.1
–0.15
–0.15
–0.15
–0.15
–0.15
–0.15
–0.60
UNITS
LTC6911-2 Only
Gain Temperature Coefficient
Channel-to-Channel Gain
Temperature Coefficient Match
Channel-to-Channel Isolation (Note 7)
Offset Voltage Magnitude
Referred to INA or INB Pins (Note 8)
Offset Voltage Magnitude Drift
Referred to INA or INB Pins (Note 8)
DC Input Resistance at
INA or INB Pins (Note 9)
VS = 5V, Gain = 1, RL = 10k
VS = 5V, Gain = 1, RL = 500Ω
VS = 5V, Gain = 2, RL = 10k
VS = 5V, Gain = 4, RL = 10k
VS = 5V, Gain = 8, RL = 10k
VS = 5V, Gain = 8, RL = 500Ω
VS = 5V, Gain = 16, RL = 10k
VS = 5V, Gain = 32, RL = 10k
VS = 5V, Gain = 64, RL = 10k
VS = 5V, Gain = 64, RL = 500Ω
VS = ±5V, Gain = 1, RL = 10k
VS = ±5V, Gain = 1, RL = 500Ω
VS = ±5V, Gain = 2, RL = 10k
VS = ±5V, Gain = 4, RL = 10k
VS = ±5V, Gain = 8, RL = 10k
VS = ±5V, Gain = 8, RL = 500Ω
VS = ±5V, Gain = 16, RL = 10k
VS = ±5V, Gain = 32, RL = 10k
VS = ±5V, Gain = 64, RL = 10k
VS = ±5V, Gain = 64, RL = 500Ω
VS = 5V, Gain = 1, RL = Open
VS = 5V, Gain = 2, RL = Open
VS = 5V, Gain = 4, RL = Open
VS = 5V, Gain = 8, RL = Open
VS = 5V, Gain = 16, RL = Open
VS = 5V, Gain = 32, RL = Open
VS = 5V, Gain = 64, RL = Open
VS = 5V, Gain = 1, RL = Open
VS = 5V, Gain = 2, RL = Open
VS = 5V, Gain = 4, RL = Open
VS = 5V, Gain = 8, RL = Open
VS = 5V, Gain = 16, RL = Open
VS = 5V, Gain = 32, RL = Open
VS = 5V, Gain = 64, RL = Open
f = 200kHz
VS = 5V, Gain = 1, RL = 10k
VS = 5V, Gain = 8, RL = 10k
VS = 5V, Gain = 64, RL = 10k
Gain = 1
Gain = 8
Gain = 1
Gain = 8
DC VINA or VINB = 0V
Gain = 0
Gain = 1
Gain = 2
Gain = 4
Gain > 4
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
2
–1
–7
–21
–28
–40
–115
0
–0.5
0.5
0.5
1.0
4.0
4.0
110
110
93
2.0
1.1
12
6.8
>100
10
5
2.5
1.25
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.60
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.40
22
12
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
0.02
2
–1
–7
–21
–28
–40
–115
0
–0.5
0.5
0.5
1.0
4.0
4.0
110
110
93
2.0
1.1
20
11
>100
10
5
2.5
1.25
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.80
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.60
22
14
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
ppm/°C
dB
dB
dB
mV
mV
µV/°C
µV/°C
MΩ
kΩ
kΩ
kΩ
kΩ
sn691112 691112fs
8
LTC6911-1/LTC6911-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications that apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, AGND = 2.5V, Gain = 1 (Digital Inputs 001), RL = 10k
to midsupply point, unless otherwise noted.
PARAMETER
LTC6911-2 Only
DC Input Resistance Match
RINA – RINB
DC Small-Signal Output Resistance
at OUTA or OUTB Pins
Wideband Noise (Referred to Input)
Voltage Noise Density
(Referred to Input)
Total Harmonic Distortion
C/I GRADES
MIN TYP MAX
CONDITIONS
Gain = 1
Gain = 2
Gain = 4
Gain > 4
DC VINA or VINB = 0V
Gain = 0
Gain = 1
Gain = 2
Gain = 4
Gain = 8
Gain = 16
Gain = 32
Gain = 64
f = 1kHz to 200kHz
Gain = 0 (Output Noise Only)
Gain = 1
Gain = 2
Gain = 4
Gain = 8
Gain = 16
Gain = 32
Gain = 64
f = 50kHz
Gain = 1
Gain = 2
Gain = 4
Gain = 8
Gain = 16
Gain = 32
Gain = 64
Gain = 8, fIN = 10kHz, VOUT = 1VRMS
●
●
●
●
Gain = 8, fIN = 100kHz, VOUT = 1VRMS
Gain-Bandwidth Product
Gain = 64, fIN = 200kHz
Note 1: Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2: The LTC6911C and LTC6911I are guaranteed functional over the
operating temperature range of – 40°C to 85°C. The LTC6911H is
guaranteed functional over the operating temperature range of – 40°C to
125°C.
Note 3: The LTC6911C is guaranteed to meet specified performance from
0°C to 70°C. The LTC6911C is designed, characterized and expected to
meet specified performance from – 40°C to 85°C but is not tested or QA
sampled at these temperatures. LTC6911I is guaranteed to meet specified
performance from – 40°C to 85°C. The LTC6911H is guaranteed to meet
specified performance from –40°C to 125°C.
Note 4: Output voltage swings are measured as differences between the
output and the respective supply rail.
Note 5: Extended operation with output shorted may cause junction
temperature to exceed the 150°C limit and is not recommended.
●
6
MIN
H GRADE
TYP MAX
UNITS
10
5
2
1
10
5
2
1
Ω
Ω
Ω
Ω
0.4
0.7
1.0
1.9
3.4
6.4
15
30
0.4
0.7
1.0
1.9
3.4
6.4
15
30
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
7.4
12.4
8.5
6.5
5.5
5.2
4.9
4.3
7.4
12.4
8.5
6.5
5.5
5.2
4.9
4.3
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
28.0
19.0
14.8
12.7
11.8
11.5
10.9
– 90
0.003
– 82
0.008
11
28.0
19.0
14.8
12.7
11.8
11.5
10.9
– 90
0.003
– 82
0.008
11
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
dB
%
dB
%
MHz
17
6
17
Note 6: Gain is measured with a DC large-signal test using an output
excursion between approximately 30% and 70% of the total supply
voltage.
Note 7: Channel-to-channel isolation is measured by applying a 200kHz
input signal to one channel so that its output varies 1VRMS and measuring
the output voltage RMS of the other channel relative to AGND with its
input tied to AGND. Isolation is calculated:
IsolationA = 20 • log10
VOUTB
V
, IsolationB = 20 • log10 OUTA
VOUTA
VOUTB
Note 8: Offset voltage referred to the INA or INB input is (1 + 1/G) times
the offset voltage of the internal op amp, where G is the nominal gain
magnitude. See Applications Information.
Note 9: Input resistance can vary by approximately ±30% part-to-part at a
given gain setting (input resistance match remains as specified).
sn691112 691112fs
9
LTC6911-1/LTC6911-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS (LTC6911-1)
LTC6911-1 Gain Shift
vs Temperature
50
0.075
GAIN OF 100 (DIGITAL INPUT 111)
30 GAIN OF 50 (DIGITAL INPUT 110)
0.025 GAIN = 10
GAIN (dB)
GAIN CHANGE (dB)
40
GAIN = 100
0.050
VS = 10V, VIN = 5mVRMS
0
GAIN = 1
GAIN OF 20 (DIGITAL INPUT 101)
20
GAIN OF 10 (DIGITAL INPUT 100)
–0.025
10 GAIN OF 5 (DIGITAL INPUT 011)
–0.050
GAIN OF 2 (DIGITAL INPUT 010)
0
–0.075
–0.100
–50
–25
–3dB FREQUENCY (MHz)
VS = 5V
OUTPUT UNLOADED
0
50
25
TEMPERATURE (°C)
75
GAIN OF 1 (DIGITAL INPUT 001)
–10
100
100
10k
100k
FREQUENCY (Hz)
1k
1M
LTC6911-1 Channel Isolation
vs Frequency
GAIN = 1
70
GAIN = 10
100
95
+SUPPLY
60
–SUPPLY
50
40
30
GAIN = 100
20
90
10
1k
1M
10k
FREQUENCY (Hz)
100k
1M
FREQUENCY (Hz)
–50
GAIN = 100
–60
–70
GAIN = 10
–80
GAIN = 1
–90
–100
0
50k
100k
150k
200k
FREQUENCY (Hz)
–30
••
••
10
GAIN
–40
•
•
100
VS = ±2.5V
TA = 25°C
INPUT REFERRED
GAIN = 1
GAIN = 10
10
GAIN = 100
10k
FREQUENCY (Hz)
100k
6911 G06
LTC6911-1 THD + Noise
vs Input Voltage
–20
VS = ±2.5V
VOUT = 1VRMS (2.83VP-P)
–30
GAIN = 100
GAIN = 100
–40
GAIN = 10
–50
GAIN = 10
–60
GAIN = 1
–70
–80
–50
–60
–70
–80
–90
–90
–100
0
50k
100k
150k
200k
FREQUENCY (Hz)
6911 G07
•
•
1
1k
10M
THD + NOISE (dB)
–40
100
LTC6911-1 Distortion vs Frequency
with Heavy Loading (RL = 500Ω)
THD (AMPLITUDE BELOW FUNDAMENTAL) (dB)
THD (AMPLITUDE BELOW FUNDAMENTAL) (dB)
LTC6911-1 Distortion vs Frequency
with Light Loading (RL = 10k)
VS = ±2.5V
VOUT = 1VRMS (2.83VP-P)
•
6911 G05
6911 G04
–30
•
6911 G03
0
85
100k
•
LTC6911-1 Noise Density
vs Frequency
VS = ±2.5V
GAIN = 1
80
REJECTION (dB)
CHANNEL-TO-CHANNEL ISOLATION (dB)
90
110
105
VIN = 5mVRMS
• VS = 2.7V
• VS = ±5V
•
1
LTC6911-1 Power Supply
Rejection vs Frequency
VS = 5V
VOUT = 1VRMS
115
8.0
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
6911 G02
6911 G01
120
10M
VOLTAGE NOISE DENSITY (nV/√Hz)
0.100
LTC6911-1 –3dB Bandwidth
vs Gain Setting
LTC6911-1 Frequency Response
6911 G08
fIN = 1kHz
–100 VS = ±5V
GAIN = 1
BW = 100Hz TO 22kHz
–110
10n
1m
0.1
1
10
INPUT VOLTAGE (VP-P)
6911 G09
sn691112 691112fs
10
LTC6911-1/LTC6911-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS (LTC6911-2)
LTC6911-2 Gain Shift
vs Temperature
50
0.100
GAIN OF 32
30
0.025
GAIN (dB)
GAIN = 8
0
GAIN = 1
–0.025
–3dB FREQUENCY (MHz)
40 GAIN OF 64
GAIN = 64
0.050
GAIN OF 16
20 GAIN OF 8
GAIN OF 4
10 GAIN OF 2
–0.050
GAIN OF 1
0
–0.075
–25
0
50
25
TEMPERATURE (°C)
75
–10
100
100
1k
100k
10k
FREQUENCY (Hz)
1M
LTC6911-2 Channel Isolation
vs Frequency
70
GAIN = 8
GAIN = 1
100
GAIN = 64
95
+SUPPLY
60
–SUPPLY
50
40
30
20
90
10
1k
1M
10k
FREQUENCY (Hz)
100k
1M
FREQUENCY (Hz)
–40
–50
–60
GAIN = 64
–70
GAIN = 8
–80
GAIN = 1
–90
–100
0
100
50k
100k
150k
200k
6911 G16
•
•
••
•
10
GAIN
–30
100
GAIN = 8
10
GAIN = 64
10k
FREQUENCY (Hz)
LTC6911-2 THD + Noise
vs Input Voltage
–20
–30
GAIN = 64
–40
–50
GAIN = 8
–60
GAIN = 1
–70
–80
–90
–100
0
50k
100k
6911 G15
VS = ±2.5V
VOUT = 1VRMS (2.83VP-P)
–40
•
VS = ±2.5V
TA = 25°C
INPUT REFERRED
1
1k
10M
100k
150k
200k
FREQUENCY (Hz)
FREQUENCY (Hz)
•
•
GAIN = 1
LTC6911-2 Distortion vs Frequency
with Heavy Loading (RL = 500Ω)
THD (AMPLITUDE BELOW FUNDAMENTAL) (dB)
THD (AMPLITUDE BELOW FUNDAMENTAL) (dB)
LTC6911-2 Distortion vs Frequency
with Light Loading (RL = 10k)
VS = ±2.5V
VOUT = 1VRMS (2.83VP-P)
•
6911 G14
6911 G13
–30
•
6911 G12
0
85
100k
•
LTC6911-2 Noise Density
vs Frequency
VS = ±2.5V
GAIN = 1
80
REJECTION (dB)
CHANNEL-TO-CHANNEL ISOLATION (dB)
90
110
105
VIN = 10mVRMS
• VS = 2.7V
• VS = ±5V
•
1
LTC6911-2 Power Supply
Rejection vs Frequency
VS = 5V
VOUT = 1VRMS
115
8.0
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
6911 G11
6911 G010
120
10M
VOLTAGE NOISE DENSITY (nV/√Hz)
–0.100
–50
THD + NOISE (dB)
GAIN CHANGE (dB)
VS = ±5V
VIN = 10mVRMS
VS = 5V
OUTPUT UNLOADED
0.075
LTC6911-2 –3dB Bandwidth
vs Gain Setting
LTC6911-2 Frequency Response
6911 G17
GAIN = 64
–50
GAIN = 8
–60
–70
–80
–90
fIN = 1kHz
–100 VS = ±5V
GAIN = 1
BW = 100Hz TO 22kHz
–110
10n
1m
0.1
1
10
INPUT VOLTAGE (VP-P)
6911 G18
sn691112 691112fs
11
LTC6911-1/LTC6911-2
U
U
U
PI FU CTIO S
INA (Pin 1): Analog Input. The input signal to the A channel
amplifier of the LTC6911-X is the voltage difference between the INA and AGND pin. The INA pin connects
internally to a digitally controlled resistance whose other
end is a current summing point at the same potential as the
AGND pin (Figure 1). At unity gain (digital input 001), the
value of this input resistance is approximately 10kΩ and
the INA pin voltage range is rail-to-rail (V+ to V–). At gain
settings above unity, the input resistance falls. The linear
input range at INA also falls inversely proportional to the
programmed gain. Tables 1 and 2 summarize this behavior. The higher gains are designed to boost lower level
signals with good noise performance. In the “zero” gain
state (digital input 000), analog switches disconnect the
INA pin internally and this pin presents a very high input
resistance. The input may vary from rail to rail in the “zero”
gain setting, but the output is insensitive to it and is forced
to the AGND potential.
Circuitry driving the INA pin must consider the LTC6911-X’s
input resistance, its lot-to-lot variance, and the variation of
this resistance from gain setting to gain setting. Signal
sources with significant output resistance may introduce
a gain error as the source’s output resistance and the
LTC6911-X’s input resistance form a voltage divider. This
is especially true at higher gain settings where the input
resistance is the lowest.
In single supply voltage applications, it is important to
remember that the LTC6911-X’s DC ground reference for
both input and output is AGND, not V–. With increasing
gains, the LTC6911-X’s input voltage range for an unclipped
output is no longer rail-to-rail but diminishes inversely to
gain, centered about the AGND potential.
G2
G1
G0
6
5
4
CMOS LOGIC
INA 1
INPUT R ARRAY
FEEDBACK R ARRAY
–
MOS-INPUT
OP AMP
V+
10 OUTA
+
10k
9 V–
AGND 2
+
10k
V–
MOS-INPUT
OP AMP
8 OUTB
–
7 V+
INB 3
691112 F01
INPUT R ARRAY
FEEDBACK R ARRAY
Figure 1. Block Diagram
sn691112 691112fs
12
LTC6911-1/LTC6911-2
U
U
U
PI FU CTIO S
AGND (Pin 2): Analog Ground. The AGND pin is at the
midpoint of an internal resistive voltage divider, developing a potential halfway between the V+ and V– pins, with an
equivalent series resistance to the pin of nominally 5kΩ
(Figure␣ 1). AGND is also the noninverting input to both the
internal channel A and channel B amplifiers. This makes
AGND the ground reference voltage for the INA, INB, OUTA
and OUTB pins. Recommended analog ground plane connection depends on how power is applied to the LTC6911-X
(see Figures 2, 3 and 4). Single power supply applications
typically use V– for the system signal ground. The analog
ground plane in single supply applications should therefore tie to V–, and the AGND pin should be bypassed to this
ground plane by a high quality capacitor of at least 1µF
(Figure 2). The AGND pin provides an internal analog
reference voltage at half the V+ supply voltage. Dual supply
applications with symmetrical supplies (such as ±5V)
have a natural system ground plane potential of zero volts,
which can be tied directly to the AGND pin, making the zero
volt ground plane the input and output reference voltage
for the LTC6911-X (Figure 3). Finally, if dual asymmetrical
power supplies are used, the supply ground is still the
natural ground plane voltage. To maximize signal swing
capability with an asymmetrical supply, however, it is
often desirable to refer the LTC6911-X’s analog input and
output to a voltage equidistant from the two supply rails V+
and V–. The AGND pin will provide such a potential when
open-circuited and bypassed with a capacitor (Figure 4).
V–
0.1µF
10
9
8
7
1
2
3
SINGLE-POINT
SYSTEM GROUND
SINGLE-POINT
SYSTEM GROUND
≥1µF
6
2
3
4
5
DIGITAL GROUND PLANE
(IF ANY)
691112 F03
Figure 3. Dual Supply Ground Plane Connection
V–
0.1µF
6
10
9
V+
0.1µF
8
7
6
4
5
LTC6911-X
4
5
1
+
ANALOG
GROUND
PLANE
7
ANALOG
GROUND
PLANE
LTC6911-X
1
8
LTC6911-X
V+
0.1µF
10
9
V+
0.1µF
V
REFERENCE
2
DIGITAL GROUND PLANE
(IF ANY)
691112 F02
Figure 2. Single Supply Ground Plane Connection
ANALOG
GROUND
PLANE
SINGLE-POINT
SYSTEM GROUND
2
3
V + + V–
REFERENCE
2
≥1µF
DIGITAL GROUND PLANE
(IF ANY)
691112 F04
Figure 4. Asymmetrical Dual Supply Ground Plane Connection
sn691112 691112fs
13
LTC6911-1/LTC6911-2
U
U
U
PI FU CTIO S
In noise sensitive applications where AGND does not
directly tie to a ground plane, as in Figures 2 and 4, it is
important to AC-bypass the AGND pin. Otherwise, channel-to-channel isolation is degraded and wideband noise
will enter the signal path from the thermal noise of the
internal voltage divider resistors that present a Thévenin
equivalent resistance of approximately 5kΩ. This noise
can reduce SNR by at least 3dB at high gain settings. An
external capacitor from AGND to the ground plane, whose
impedance is well below 5kΩ at frequencies of interest,
will filter and suppress this noise. A 1µF high quality
capacitor is effective for frequencies down to 1kHz. Larger
capacitors extend this suppression to lower frequencies.
This issue does not arise in dual supply applications
because the AGND pin ties directly to ground.
In applications requiring an analog ground reference other
than half the total supply voltage, the user can override the
built-in analog ground reference by tying the AGND pin to
a reference voltage within the AGND voltage range specified in the Electrical Characteristics table. The AGND pin
will load the external reference with approximately 5kΩ
returned to the half-supply potential. AGND should still be
capacitively bypassed to a ground plane as noted above.
Do not connect the AGND pin to the V– pin.
INB (Pin 3): Analog Input. Refer to INA pin description.
G0, G1, G2 (Pins 4, 5, 6): CMOS-Level Digital Gain
Control Inputs. G2 is the most significant bit (MSB) and G0
is the least significant bit (LSB). These pins control the
voltage gain settings for both channels (see Tables 1
and␣ 2). Each channel’s gain cannot be set independent of
the other channel. The logic input pins (G pins) are allowed
to swing from V– to 10.5V above V–, regardless of V+ so
long as the logic levels meet the minimum requirements
specified in the Electrical Characteristics table. The G0, G1
and G2 pins are high impedance CMOS logic inputs, but
have small pull-down current sources (<10µA) which will
force both channels into the “zero” gain state (digital input
000) if the logic inputs are externally floated. No speed
limitation is associated with the digital logic because it is
memoryless and much faster than the analog signal path.
V–, V+ (Pins 7, 9): Power Supply Pins. The V+ and V– pins
should be bypassed with 0.1µF capacitors to an adequate
analog ground plane using the shortest possible wiring.
Electrically clean supplies and a low impedance ground
are important for the high dynamic range available from
the LTC6911-X (see further details under the AGND pin
description). Low noise linear power supplies are recommended. Switching power supplies require special care to
prevent switching noise coupling into the signal path,
reducing dynamic range.
OUTB (Pin 8): Analog Output. This is the output of the B
channel internal operational amplifier and can swing railto-rail (V+ to V–) as specified in the Electrical Characteristics table. The internal op amp remains active at all times,
including the zero gain setting (digital input 000). For best
performance, loading the output as lightly as possible will
minimize signal distortion and gain error. The Electrical
Characteristics table shows performance at output currents up to 10mA, and the current limits which occur when
the output is shorted to mid-supply at 2.7V and ±5V
supplies. Signal outputs above 10mA are possible but
current-limiting circuitry will begin to affect amplifier
performance at approximately 20mA. Long-term operation above 20mA output is not recommended. Do not
exceed a maximum junction temperature of 150°C. The
output will drive capacitive loads up to 50pF. Capacitances
higher than 50pF should be isolated by a series resistor to
preserve AC stability.
OUTA (Pin 10): Analog Output. Refer to OUTB pin
description.
sn691112 691112fs
14
LTC6911-1/LTC6911-2
U
W
U U
APPLICATIO S I FOR ATIO
Functional Description
Timing Constraints
The LTC6911-1/LTC6911-2 are small outline, wideband
inverting 2-channel amplifiers whose voltage gain is digitally programmable. Each delivers a choice of eight voltage gains, controlled by the 3-bit digital parallel interface
(G pins), which accept CMOS logic levels. The gain code
is always monotonic; an increase in the 3-bit binary
number (G2 G1 G0) causes an increase in the gain. Tables
1 and 2 list the nominal voltage gains for LTC6911-1 and
LTC6911-2 respectively. Gain control within each amplifier occurs by switching resistors from a matched array in
or out of a closed-loop op amp circuit using MOS analog
switches (Figure 1). Bandwidth depends on gain setting.
Curves in the Typical Performance Characteristics section
show measured frequency responses.
Settling time in the CMOS gain-control logic is typically
several nanoseconds and is faster than the analog signal
path. When amplifier gain changes, the limiting timing is
analog, not digital, because the effects of digital input
changes are observed only through the analog output
(Figure 1). The LTC6911-X’s logic is static (not latched)
and therefore lacks bus timing requirements. However, as
with any programmable-gain amplifier, each gain change
causes an output transient as the amplifier’s output moves,
with finite speed, toward a differently scaled version of the
input signal. Varying the gain faster than the output can
settle produces a garbled output signal. The LTC6911-X
analog path settles with a characteristic time constant or
time scale, τ, that is roughly the standard value for a first
order band limited response:
Digital Control
Logic levels for the LTC6911-X digital gain control inputs
(Pins 4, 5, 6) are nominally rail-to-rail CMOS, but can
swing above V+ so long as the positive swing does not
exceed 10.5V with respect to V–. Each logic input has a
small pull-down current source which can sink up to 10µA
and is used to force the part into a gain of “zero” if the logic
inputs are left unconnected. A logic 1 is nominally V+. A
logic 0 is nominally V– or alternatively, 0V when using ±5V
supplies. The parts are tested with the values listed in the
Electrical Characteristics table. Digital Input “High” and
“Low” voltages are 10% and 90% of the nominal full
excursion on the inputs. That is, the tested logic levels are
0.27V and 2.43V with a 2.7V supply, 0.5V and 4.5V with a
5V supply, and 0.5V and 4.5V with ±5V supplies. Do not
attempt to drive the digital inputs with TTL logic levels. TTL
logic sources should be adapted with suitable pull-up
resistors to V+ keeping in mind the internal pull-down
current sources so that for a logic 1 they will swing to the
positive rail.
τ = 0.35/(2 π f–3dB)
See the –3dB BW vs Gain Setting graph in the Typical
Performance Characteristics.
Offset Voltage vs Gain Setting
The Electrical Characteristics table lists DC gain dependent voltage offset error in two gain configurations. The
voltage offsets listed, VOS(IN), are referred to the input pin
(INA or INB). These offsets are directly related to the
internal amplifier input voltage offset, VOS(OA), by the
magnitude of programmed gain, G:
 G 
VOS(OA) = VOS(IN) 

 1 + G
The input referred offset, VOS(IN), for any gain setting can
be inferred from VOS(OA) and the gain magnitude, G. For
example, an internal offset VOS(OA) of 1mV will appear
referred to the INA and INB pins as 2mV at a gain setting
sn691112 691112fs
15
LTC6911-1/LTC6911-2
U
W
U U
APPLICATIO S I FOR ATIO
of 1, or 1.5mV at a gain setting of 2. At high gains, VOS(IN)
approaches VOS(OA). (Offset voltage is random and can
have either polarity centered on 0V.) The MOS input
circuitry of the internal op amp in Figure 1 draws negligible
input currents (unlike some op amps), so only VOS(OA) and
G affect the overall amplifier’s offset.
AC-Coupled Operation
Adding capacitors in series with the INA and INB pins
convert the LTC6911-X into a dual AC-coupled inverting
amplifier, suppressing the input signal’s DC level (and also
adding the additional benefit of reducing the offset voltage
from the LTC6911-X’s amplifier itself). No further components are required because the input of the LTC6911-X
biases itself correctly when a series capacitor is added.
The INA and INB analog input pins connect internally to a
resistor whose nominal value varies between 10k and 1k
depending on the version of LTC6911 used (see the
rightmost column of Tables 1 and 2). Therefore, the low
frequency cutoff will vary with capacitor and gain setting.
For example, if a low frequency corner of 1kHz or lower on
the LTC6911-1 is desired, use a series capacitor of 0.16µF
or larger. A 0.16µF capacitor has a reactance of 1kΩ at
1kHz, giving a 1kHz lower –3dB frequency for gain settings
of 10V/V through 100V/V. If the LTC6911-1 is operated at
lower gain settings with an 0.16µF capacitor, the higher
input resistance will reduce the lower corner frequency
down to 100Hz at a gain setting of 1V/V. These frequencies
scale inversely with the value of the input capacitor used.
Note that operating the LTC6911 family in “zero” gain
mode (digital inputs 000) open circuits the INA and INB
pins and this demands some care if employed with a series
AC-coupled input capacitor. When the chip enters the zero
gain mode, the opened INA or INB pin tends to sample and
freeze the voltage across the capacitor to the value it held
just before the zero gain state. This can place the INA or
INB pin at or near the DC potential of a supply rail (the INA
or INB pin may also drift to a supply potential in this state
due to small junction leakage currents). To prevent driving
the INA or INB pin outside the supply limit and potentially
damaging the chip, avoid AC input signals in the zero gain
state with an AC-coupled capacitor. Also, switching later
to a nonzero gain value will cause a transient pulse at the
output of the LTC6911-1 (with a time constant set by the
capacitor value and the new LTC6911-1 input resistance
value). This occurs because the INA and INB pins return to
the AGND potential forcing transient current sourced by
the amplifier output to charge the AC-coupling capacitor to
its proper DC blocking value.
SNR and Dynamic Range
The term “dynamic range” is much used (and abused)
with signal paths. Signal-to-noise ratio (SNR) is an unambiguous comparison of signal and noise levels, measured
in the same way and under the same operating conditions.
In a variable gain amplifier, however, further characterization is useful because both noise and maximum signal
level in the amplifier will vary with the gain setting, in
general. In the LTC6911-X, maximum output signal is
independent of gain (and is near the full power supply
voltage, as detailed in the Swing sections of the Electrical
Characteristics table). The maximum input level falls with
increasing gain, and the input-referred noise falls as well
(as also listed in the table). To summarize the useful signal
range in such an amplifier, we define Dynamic Range (DR)
as the ratio of maximum input (at unity gain) to minimum
input-referred noise (at maximum gain). This DR has a
physical interpretation as the range of signal levels that
will experience an SNR above unity V/V or 0dB. At a 10V
total power supply, DR in the LTC6911-X (gains 0V/V to
100V/V) is typically 120dB (the ratio of a nominal 9.9VP-P,
or 3.5VRMS (maximum input), to the 3.8µVRMS (high gain
input noise). The SNR of an amplifier is the ratio of input
level to input-referred noise, and can be 110dB with the
LTC6911 family at unity gain.
sn691112 691112fs
16
LTC6911-1/LTC6911-2
U
W
U U
APPLICATIO S I FOR ATIO
Construction and Instrumentation Cautions
Electrically clean construction is important in applications
seeking the full dynamic range of the LTC6911 family of
dual amplifiers. It is absolutely critical to have AGND either
AC bypassed or wired directly, using the shortest possible
wiring, to a low impedance ground return for best channelto-channel isolation. Short, direct wiring will minimize
parasitic capacitance and inductance. High quality supply
bypass capacitors of 0.1µF near the chip provide good
decoupling from a clean, low inductance power source.
But several cm of wire (i.e., a few microhenrys of inductance) from the power supplies, unless decoupled by
substantial capacitance (>10µF) near the chip, can create
a high-Q LC resonance in the hundreds of kHz in the chip’s
supplies or ground reference. This may impair circuit
performance at those frequencies. A compact, carefully
laid out printed circuit board with a good ground plane
makes a significant difference in minimizing distortion and
maximizing channel isolation. Finally, equipment to measure amplifier performance can itself add to distortion or
noise floors. Checking for these limits with wired shorts
from INA to OUTA and INB to OUTB in place of the chip is
a prudent routine procedure.
sn691112 691112fs
17
LTC6911-1/LTC6911-2
U
TYPICAL APPLICATIO
Expanding an ADC’s Dynamic Range
Figure 5 shows a compact 2-channel data acquisition
system for wide ranging input levels. This figure combines
an LTC6911-X programmable amplifier (10-lead MSOP)
with an LTC1865 analog-to-digital converter (ADC) in an
8-lead MSOP. This ADC has 16-bit resolution and a
V+
maximum sampling rate of 250ksps. An LTC6911-1, for
example, expands the ADC’s input amplitude range by
40dB while operating from the same single 5V supply. The
499Ω resistor and 270pF capacitor couple cleanly between the LTC6911-X’s output and the switched-capacitor
inputs of the LTC1865.
0.1µF
7
9
V+
0.1µF
VINA
AGND
1
10
499Ω
VCC
270pF
≥1µF
2
LTC1865
LTC6911-X
3
8
GND
499Ω
SCK
SDO
CH1
VINB
CONV
CH0
SDI
691112 F05
270pF
ADC INTERFACE
691112 F05
4
5
6
GAIN CONTROL
Figure 5. Expanding a Dual Channel ADC’s Dynamic Range
sn691112 691112fs
18
LTC6911-1/LTC6911-2
U
PACKAGE DESCRIPTIO
MS Package
10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1661)
0.889 ± 0.127
(.035 ± .005)
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
0.50
0.305 ± 0.038
(.0197)
(.0120 ± .0015)
BSC
TYP
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
0.497 ± 0.076
(.0196 ± .003)
REF
10 9 8 7 6
3.00 ± 0.102
(.118 ± .004)
(NOTE 4)
4.90 ± 0.152
(.193 ± .006)
DETAIL “A”
0° – 6° TYP
GAUGE PLANE
1 2 3 4 5
0.53 ± 0.152
(.021 ± .006)
DETAIL “A”
0.86
(.034)
REF
1.10
(.043)
MAX
0.18
(.007)
SEATING
PLANE
0.17 – 0.27
(.007 – .011)
TYP
0.50
(.0197)
BSC
0.127 ± 0.076
(.005 ± .003)
MSOP (MS) 0603
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
sn691112 691112fs
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LTC6911-1/LTC6911-2
U
TYPICAL APPLICATIO
Fully Differential Amplifier with Digitally Programmable Gain
High Dynamic Range (PGA Input)
–5V
0.1µF
VIN+
1
10
2
9
VIN–
3
LTC6911-1
OR
4 LTC6911-2
5
1
5V
8
7
6
0.1µF
8
LTC1992-1
OR
2
7
LTC1992-2
OR
3
6
LTC1992-5
OR
0.1µF 4
5
LTC1992-10
–5V
0.1µF
VOUT+
VOUT–
G0 G1 G2
DIGITAL GAIN CONTROL
High CMRR (Differential Input)
–5V
VIN+
VIN–
5V
0.1µF
0.1µF
8
1
LTC1992-1
OR
7
2
LTC1992-2
OR
6
3
LTC1992-5
OR
5
4
LTC1992-10
–5V
1
10
2
9
LTC6911-1
OR
4 LTC6911-2
5
3
0.1µF
8
5V
VOUT+
VOUT–
7
6
0.1µF
691112 TA03
G0 G1 G2
DIGITAL GAIN CONTROL
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT 1228
100MHz Gain Controlled Transconductance Amplifier
Differential Input, Continuous Analog Gain Control
LT1251/LT1256
40MHz Video Fader and Gain Controlled Amplifier
Two Input, One Output, Continuous Analog Gain Control
LTC1564
10kHz to 150kHz Digitally Controlled Filter and PGA
Continuous Time, Low Noise 8th Order Filter and 4-Bit PGA
LTC6910
Digitally Controlled Programmable Gain Amplifier in SOT-23
Single Channel Version of the LTC6911
LTC6915
Digitally Controlled Programmable Instrumentation
Amplifier with SPI Interface
14 Bits of Gain Control
®
sn691112 691112fs
20
Linear Technology Corporation
LT/TP 0104 1K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2004