LXMG221W-0700034-D1 34W 700mA Dimming LED Driver Module ® TM P RODUCTION D ATASHEET DESCRIPTION The BRITE_A terminal also provides a shutdown function, when pulled down below 1V, to meet ENERGY STAR® requirement to be less than 0.5W in standby mode. To reduce audible noise the internal switching frequency remains above 30kHz. Safety features include open output circuit protection, whole string short circuit protection, and over temperature protection if the hot spot case temperature exceeds 85 to 95°C. The operating ambient temperature range is 30°C to 60°C, and the compact enclosure is rated to IP66, and designed to meet UL8750 for SSL. High Efficiency Active Power Factor Correction Universal AC Input 100~277VAC Dimming Input Provides 15% to 100% Range, Plus Shutdown Fully Isolated Plastic Case (IP66) Small Compact Size High Reliability Full Protection: OVP,SCP, OTP, Maximum Power Limit Complies with UL8750 RoHS Compliant ENERGY STAR® Compliant WWW . Microsemi .C OM The LXMG221W-0700034-D1 is a fully enclosed compact solid-state LED lighting driver module. It operates from a universal AC input supply in the range of 100 to 277VAC, 50/60Hz to drive one string of LED’s with active power factor correction. LED string voltage can range from 20 to 48V at a constant current of 700mA. Control terminal leads include a dimming input BRITE_A with a dedicated RETURN lead. The amplitude of the output LED string current will vary from 15% to 100% corresponding to a 1VDC to 10VDC signal on the BRITE_A input following the IEC 60929 Analog Control Specification Standard. KEY FEATURES APPLICATIONS SSL Class 2 LED Driver Module LED Lighting IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com PRODUCT HIGHLIGHT LXMG221W-0700034-D1 Photo is representative only, actual product may differ slightly ORDER INFORMATION Part Number Input Voltage LXMG221W-0700034-D1 100VAC to 277VAC 50/60 Hz Copyright 2011 Rev 1.0a, 10/24/11 Output Current One 700mA Dimmable Current Source 20V to 48V Anode Voltage Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 1 LXMG221W-0700034-D1 34W 700mA Dimming LED Driver Module ® TM P RODUCTION D ATASHEET ABSOLUTE MAXIMUM RATINGS Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. RECOMMENDED OPERATING CONDITIONS (R.C.) WWW . Microsemi .C OM Input Voltage (VIN) ......................................................................................................................................... 90 VAC to 305VAC Input Power ....................................................................................................................................................................... 45W Output LED String Current ............................................................................................................. 800mA (Internally Limited) Output String Voltage .......................................................................................................................... 56V (Internally Limited) Output Power .................................................................................................................................................................... 38W Input Signal Voltage (BRITE_A Input) ................................................................................................................... -0.3V to 11V Ambient Operating Temperature, zero airflow ....................................................................................................-30°C to 60°C Hot Spot Case Temperature, zero airflow ......................................................................................................................... 85°C Storage Temperature Range ..............................................................................................................................-40°C to 85°C This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. All specifications are typical at 25°C unless otherwise stated. Min. and Max. columns indicate values beyond which the inverter, although operational, might not function optimally. Parameter Symbol Min Max Units VIN 100 277 VAC VBRITE_A 1 10 V LED String Voltage VLED 20 48 V OUT- Sink Current OUT-ISINK Input Supply Voltage Range Linear BRITE_A Control Input Voltage Range R.C. 700 mA ELECTRICAL CHARACTERISTICS Unless otherwise specified, the following specifications apply over the recommended operating conditions and ambient temperature of 25C ; VIN = 100 to 277VAC; BRITE_A = 10kΩ to BRITE_RTN Parameter Symbol Input Voltage VIN Off Power PIN(MIN) Input AC Current Maximum Inrush Current Typ 90 BRITE_A ≤ 0.5V (ENERGY STAR® Requirement) Max Units 305 VAC 0.5 W Measured at full load and 120VAC Input 0.38 A I277 Measured at full load and 277VAC Input 0.16 A IINRUSH THD Measure at 277VAC (First 10µS) 60 A After 10µS 3 A Maximum Output Power; 120, 208, 240, 277VAC; 50/60Hz 0.9 VLED = 48V 84 85 Maximum Output Power; 120, 208, 240, 277VAC; 50/60Hz % 20 % 735 mA 48 V OUTPUTS Average Sink Current IOUT 665 LED String Voltage VLED 20 Ripple Current (pk-pk) IOUT-RIPPLE Pk-pk Ripple Current/Average Current Line Regulation IOUT-LINE VIN = Nominal ± 10% Copyright 2011 Rev 1.0a, 10/24/11 700 20 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 % 1 % Page 2 LXMG221W-0700034-D1 Total Harmonic Distortion Line Frequency 47 to 63 Hz Min I120 Power Factor Peak Efficiency (Note 1) Test Conditions / Comment LXMG221W-0700034-D1 34W 700mA Dimming LED Driver Module ® TM P RODUCTION D ATASHEET ELECTRICAL CHARACTERISTICS Unless otherwise specified, the following specifications apply over the recommended operating conditions and ambient temperature of 25C ; VIN = 100 to 277VAC; BRITE_A = 10kΩ to BRITE_RTN Symbol Test Conditions / Comment Min Load Regulation IOUT-LOAD VOUT+ = 20V to 48V Turn-on Time DELAY Power ON to Full Bright Output Current, Vin = 120VAC Power ON to Full Bright Output Current, Vin = 230VAC Typ Max Units 5 % 1.8 sec 0.8 Dimming BRITE_A Voltage for Full Bright Potentiometer Dimming on BRITE_A BRITE_A Voltage for Full Dim VBRITE_A_MAX 9.5 10 10.5 V POT 8 10 12 kΩ VBRITE_A_MIN 0.95 1 1.05 V Minimum Output Current Output Current Dim Range (Analog Dimming) Shutdown Voltage Threshold IMIN BRITE_A = 0.9V 15 % of Max ILED = 105mA, BRITE_A = 0.9V Versus BRITE_A ≥ 10V 7:1 RATIO VBRITE_SD 0.85 V 56 V No Limit sec WWW . Microsemi .C OM Parameter Protection Overvoltage Protection VOV Maximum OUT+ Short Circuit Duration Tsc Time duration that OUT+ may be shorted Over Temperature Shutdown TSD Over Case Temperature Protection Hot Spot 85 95 °C Safety & EMC Compliance UL8750 UL/CE EN 61347-1, EN61347-2-13 EMI Standards FCC Title 47, Part 15 Conducted & Radiated emission Test Class B EMS Standard ANSI C82.77-2002 Harmonic Current Emissions Energy Star Standby Power, PF (Full Load) IEC 61000-4-2 Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact Discharge 5 years / 50,000 hours @ 100% duty at maximum case temperature 55°C RoHS Environmental Standards 1) LXMG221W-0700034-D1 Life Expectancy Note: Peak Efficiency is the efficiency at a given sweet spot over the range of input voltage and output current. Copyright 2011 Rev 1.0a, 10/24/11 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 3 LXMG221W-0700034-D1 ® TM 34W 700mA Dimming LED Driver Module P RODUCTION D ATASHEET LEAD DESCRIPTION Pin # Description WWW . Microsemi .C OM Name INPUT TERMINAL LEADS (18AWG) 16/30 Stranded BLACK VIN Line Voltage WHITE VIN Neutral Main Input Power Supply Line 100 to 277VAC Main Input Power Supply Neutral CONTROL TERMINAL LEADS (22AWG) 7/30 Stranded PURPLE BRITE_A GRAY BRITE_RTN Analog Dimming Input Dimming Return OUTPUT TERMINAL LEADS (18AWG) RED OUT+ LED String Anode Voltage (High Side) BLUE OUT- -LED Cathode Voltage (Low Side) APPLICATION INFORMATION OUT+ NEUTRAL 90 V AC to 305 V AC 700mA LXMG221W-0700034-D1 OUTRETURN 1 V to 10 V <0 .85V OFF BRITE _ A LINE LXMG221W-0700034-D1 Copyright 2011 Rev 1.0a, 10/24/11 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 4 LXMG221W-0700034-D1 ® TM 34W 700mA Dimming LED Driver Module P RODUCTION D ATASHEET MECHANICAL DRAWING WWW . Microsemi .C OM ` AC L LXMG221W-0350017-D0 BRITE A RETURN AC N OUT(+) OU(T-)- 160 160 mm Wire length is 160mm ± 5mm, stripped 12mm ± 2mm UL1015 AWG#18 16/30 stranded 105°C Input & Output wires; AWG#22 7/30 stranded Control wires Hole in center, mounting tab slot width 4mm LXMG221W-0700034-D1 Copyright 2011 Rev 1.0a, 10/24/11 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 5 LXMG221W-0700034-D1 TM ® 34W 700mA Dimming LED Driver Module P RODUCTION D ATASHEET NOTES WWW . Microsemi .C OM LXMG221W-0700034-D1 PRELIMINARY DATA – Information contained in this document is pre-production data and is proprietary to Microsemi. It may not be modified in any way without the express written consent of Microsemi. Product referred to herein is offered in pre-production form only and may not have completed Microsemi’s Quality Assurance process for Release to Production. Microsemi reserves the right to change or discontinue this proposed product at any time. DS_ LXMG221W-0700034-D1 Copyright 2011 Rev 1.0a, 10/24/11 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 6