M150XN07 V.2 Product Specification AU OPTRONICS CORPORATION Product Specification 15.0” XGA Color TFT-LCD Module Model Name: M150XN07 V.2 Approved by Prepared by CC Chiu TC Tsai DDBU Marketing Division / AU Optronics corporation Customer Checked & Approved by ver 0.1 1/29 M150XN07 V.2 Product Specification Product Specification 15.0” XGA Color TFT-LCD Module Model Name: M150XN07 V.2 (u) Preliminary Specifications ( ) Final Specifications Note: This Specification is subject to change without notice. ver 0.1 2/29 M150XN07 V.2 Product Specification Contents 1.0 Handling Precautions............................................................. 5 2.0 General Description ............................................................... 6 2.1 Display Characteristics .............................................................................................................. 6 2.2 Optical Characteristics............................................................................................................... 7 3.0 Functional Block Diagram .................................................... 12 4.0 Absolute Maximum Ratings ................................................. 13 4.1 TFT LCD Module ...................................................................................................................... 13 4.2 Backlight Unit ............................................................................................................................ 13 4.3 Absolute Ratings of Environment............................................................................................ 13 5.0 Electrical characteristics...................................................... 14 5.1 TFT LCD Module ...................................................................................................................... 14 5.1.1 Power Specification .............................................................................................................................14 5.1.2 Signal Electrical Characteristics...........................................................................................................15 5.2 Backlight Unit ............................................................................................................................ 16 6.0 Signal Characteristic............................................................ 17 6.1 Pixel Format Image................................................................................................................... 17 6.2 The input data format ............................................................................................................... 18 6.3 Signal Description .................................................................................................................... 19 6.4 Interface Timing ........................................................................................................................ 20 6.4.1 Timing Characteristics .........................................................................................................................20 6.4.2 Timing diagram....................................................................................................................................21 6.5 Power ON/OFF Sequence....................................................................................................... 22 7.0 Connector & Pin Assignment ............................................... 23 7.1 TFT LCD Module ...................................................................................................................... 23 7.2 Backlight Unit ............................................................................................................................ 24 7.3 Signal for Lamp connector....................................................................................................... 24 8.0 Reliability ............................................................................ 25 9.0 Safety .................................................................................. 26 9.1 Sharp Edge Requirements ...................................................................................................... 26 9.2 Materials .................................................................................................................................... 26 9.2.1 Toxicity................................................................................................................................................26 9.2.2 Flammability........................................................................................................................................26 9.3 Capacitors ................................................................................................................................. 26 10.0 Other requirement............................................................. 26 10.1 National Test Lab Requirement............................................................................................. 26 10.2 Label ........................................................................................................................................ 26 ver 0.1 3/29 M150XN07 V.2 Product Specification 11.0 Mechanical Characteristics ................................................ 27 Record of Revision Version and Date Page 0.1 2005/02/14 All Old description New Description Remark First Edition for Customer ver 0.1 4/29 M150XN07 V.2 Product Specification 1.0 Handling Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. 8) Do not press or pat the panel surface by fingers,hand or tooling. 9) Do not press the reflector sheet at the back of the module to any directions. 10) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL reflector edge softly. Otherwise the TFT module may be damaged. 11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT module. 12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged. ver 0.1 5/29 M150XN07 V.2 Product Specification 2.0 General Description This specification applies to the 15.0 inch Color TFT/LCD Module M150XN07 V2. This module is designed for a display unit of personal computer. The display supports the XGA (1024 (H) x 768(V)) screen format and 16.2M colors (RGB 6-bits + FRC data). All input signals are 1 Channel LVDS interface compatible. This module does not contain an inverter card for backlight. 2.1 Display Characteristics The following items are characteristics summary on the table under 25 ℃ condition: ITEMS Screen Diagonal Active Area Pixels H x V Pixel Pitch Pixel Arrangement Display Mode White Luminance Contrast Ratio Optical Rise Time/Fall Time Color Saturation Nominal Input Voltage VDD Power Consumption (VDD line + CCFL line) Weight Physical Size Electrical Interface Support Color Temperature Range Operating Storage (Shipping) Surface Treatment Unit [mm] [mm] [mm] 2 [cd/m ] [msec] [Volt] [Watt] [Grams] [mm] o [ C] o [ C] SPECIFICATIONS 381 (15”) 304.128 (H) x 228.096 1024(x3) x 768 0.297 (per one triad) x 0.297 R.G.B. Vertical Stripe TN mode, Normally White 250 (Typ) @ 8mA 500 : 1 (Typ) 12 (Typ) 65% NTSC +3.3 V 13.3 W (Typ.) @8mA (All Black Pattern) (Note 1) 1100 (Typ) Min. Typ. Horizatal(H) 326.0 326.5 Vertical(V) 253.0 253.5 Depth(D) 1 Channel LVDS 16.2M colors (RGB 6-bit + FRC data) Max. 327.0 254.0 12.0 0 to +50 -20 to +60 Hard-coating (3H), anti-glare treatment Note 1 :System should warm up for at least one hour ver 0.1 6/29 M150XN07 V.2 Product Specification 2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25 ℃ (Room Temperature): Item Unit Conditions Min. Typ. Max. Horizontal (Right) 65 TBD CR = 10 (Left) 65 Viewing Angle [degree] (Up) (Down) Horizontal CR = 5 Vertical CR = 5 (Right) (Left) (Up) (Down) TBD [msec] Color / Chromaticity Coordinates (CIE) Coordinates (CIE) White White Luminance @ CCFL 8mA (center) [cd/m 2] Luminance Uniformity [%] Crosstalk (in 75Hz) [%] Flicker dB keep total 65 55 120(Mayb TBD TBD TBD TBD TBD 500 Rising Time - TBD TBD Falling Time - TBD TBD Rising + Falling - 12 Red x 0.61 0.64 0.67 Red y 0.30 0.33 0.36 Green x 0.27 0.30 0.33 Green y 0.56 0.59 0.62 Blue x 0.12 0.15 0.18 Blue y 0.07 0.10 0.13 White x 0.28 0.31 0.34 White y 0.30 0.33 0.36 200 250 - 75 80 Note 2 Normal Direction Response Time - e 60,60) Contrast ratio Color Vertical CR = 10 Note 1.2 - Note 1 1.5 Note 3 -20 Note 4 Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A , BM 7 ,CS-1000, CA210, SR_3 & EZ Contrast(ELDIM)* ) Aperture 1∘with 50cm viewing distance Test Point Center (VESA point 9) Environment < 1 lux LCD Module PR-880 / BM5A / BM7 measuring distance Module Driving Equipment ver 0.1 7/29 M150XN07 V.2 Product Specification *’ EZ Contrast is different measurement tool with very close viewing distance. ver 0.1 8/29 M150XN07 V.2 Product Specification Note 1: Definition of Response time The output signals of photo detector are measured when the input signals are changed from “Black” to “White” (rising time), and from “White” to “Black ”(falling time), respectively. The response time is interval between the 10% and 90% of amplitudes. % Tr F Tr R 100 90 Optical White Black White response 10 0 Note 2: Brightness uniformity of these 9 points is defined as below 90 % 50 % 10 % 10 % 50 % 90 % Uniformity = Minimum Luminance in 9 points (1 - 9) × 100% Maximum Luminance in 9 Points (1 - 9) ver 0.1 9/29 M150XN07 V.2 Product Specification Note 3: Crosstalk is defined as below : 1/2 1/6 2/3 1/6 A 1/2 1/3 1/6 A’ 1/6 1/3 1/2 1/2 B B’ 184 gray level 2/3 184 gray level Unit: percentage of dimension of display area 0 gray level l LA-LA’ l / LA x 100%= 1.5% max., L A and LB are brightness at location A and B l LB-LB’ l / LB x 100%= 1.5% max., L A’ and L B’ are brightness at location A ’ and B’ Note 4: Test Paterm: Subchecker Pattern at 127 gray level 30mm CA210 FFT Sub Checker Pattern A0 A30 R GB R GB Gray Level = L127 R GB R GB R GB R GB Gray Level = L0 ver 0.1 10/29 M150XN07 V.2 Product Specification Amplitude AC DC Time Flicker (dB) = 20 log AC Level(at 30 Hz) DC Level ver 0.1 11/29 M150XN07 V.2 Product Specification 3.0 Functional Block Diagram The following diagram shows the functional block of the 15.0 inches wide Color TFT/LCD Module: AU ASIC Y-Driver IC + 3.3V Timing Controller Connector LVDS G1 LVDS Receiver TFT-LCD 1024(3)*768 Pixels RSDS Transmitter X-Driver IC G768 D1 D3072 2 CCFL DC/DC Converter Gamma Correction DC POWER Mating Type: Inverter CWY20G – A0G16 / MSB240420 JST-BHR-03VS-1 HRS SM02(8.0)B-BHS-1-TB DF14-20S-1.25C ver 0.1 12/29 M150XN07 V.2 Product Specification 4.0 Absolute Maximum Ratings Absolute maximum ratings of the module is as following: 4.1 TFT LCD Module Item Symbol Min Max Unit Conditions Logic/LCD Drive VDD 0.3 +3.6 [Volt] Note 1,2 4.2 Backlight Unit Item Symbol Min Max Unit Conditions CCFL Current IRCFL - 8.5 [mA] rms Note 1,2 Min Max Unit Conditions 4.3 Absolute Ratings of Environment Item Symbol o Operating Temperature TOP 0 +50 [ C] Note 3 Operating Humidity HOP 8 90 [%RH] Note 3 o Storage Temperature TST -20 +60 [ C] Note 3 Storage Humidity HST 8 90 [%RH] Note 3 Note 1: With in Ta (25℃ ) Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard) . Please refer the graph below for the corresponding of temperature and humidity." ver 0.1 13/29 M150XN07 V.2 Product Specification 5.0 Electrical characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Input power specifications are as follows; Symbol Parameter Condition Min Typ Max Units 3.0 3.3 3.6 [Volt] ±10% VDD Logic/LCD Drive Voltage IDD VDD current - 600 700 [mA] Vin=3.3V , Gray Bar Pattern, at 60Hz Irush PDD LCD Inrush Current VDD Power - 2.0 3 2.3 [A] [Watt] VDDrp Allowable Logic/LCD Drive Ripple Voltage 100 [mV] p-p Note Vin=3.3V , Gray Bar Pattern, at 60Hz Vin=3.3V , All Black Pattern, at 75Hz Note: Measurement conditions: +5.0V +3.3V Q3 AO6402 D6 D5 D2 D1 F1 S (LCD Module Input) G R1 47K VCC (High to Low) Control Signal D1 D2 D5 D6 C1 1uF/16V Q3 AO6402 R2 G SW S 1K C3 +12.0V VR1 0.01uF/25V 47K C2 1uF/25V 3.3V 90% 10% 0V 470 us Vin rising time ver 0.1 14/29 M150XN07 V.2 Product Specification 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when Vin is off It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail. Each signal characteristics are as follows; Symbol Parameter Differential Input High Threshold Differential Input Low Threshold Input Differential Voltage Differential Input Common Mode Voltage VTH VTL │VID│ VICM Min Typ Max Units Condition - - 100 [mV] VICM = 1.2V Note -100 - - [mV] VICM = 1.2V Note 100 400 600 [mV] 1.1 - 1.45 [V] Note VTH/VTL = ± 100mV Note Note: LVDS Signal Waveform VTH │VID│ VTL VICM VSS ver 0.1 15/29 M150XN07 V.2 Product Specification 5.2 Backlight Unit Parameter guideline for CCFL Inverter Symbol IRCFL Parameter Min. Typ. Max. CCFL operation range 2.5 8 8.5 Unit Condition [mA] (Ta=25oC) rms Note 4 ICFL CCFL Inrush current - - 20 [mA] FCFL CCFL Frequency 40 55 80 [KHz] 1450 - - (Ta=25 oC) Note 1 ViCFL (0oC) CCFL Ignition Voltage [Volt] (Ta=0oC) Note 3 rms (reference) ViCF (25oC) [Volt] CCFL Ignition Voltage 1100 - - (Ta=25 oC) Note 3 rms (reference) CCFL Discharge Voltage 620 710 [Volt] (@8mA) (@2.5mA) rms 10 11 [Watt] - VCFL CCFL Power consumption PCFL - (Ta=25 oC) Note 2 (Ta=25 oC) Note 2 @8mA(excluding inverter) Note 1: CCFL frequency should be carefully determined to avoid interference between inverter and TFT LCD. Note 2: Calculator value for reference (IRCFLxVCFLx2=PCFL). Note 3: CCFL inverter should be able to give output a voltage more than 1450 volt. Lamp units need 1450 volt minimum for ignition. Note 4: CCFL life time is 30,000hr at 8.0mA, it ’s defined as when the brightness is reduced by half. It ’s recommended not to exceed 8.0mA for CCFL life time concern and it ’s prohibited to exceed 8.5mA for safety concern. ver 0.1 16/29 M150XN07 V.2 Product Specification 6.0 Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship of the input signals and LCD pixel format. ver 0.1 17/29 M150XN07 V.2 Product Specification 6.2 The input data format CLKIN+ CLKINRIN0 +/- OG0 OR5 OR4 OR3 OR2 OR1 OR0 RIN1 +/- OB1 OB0 OG5 OG4 OG3 OG2 OG1 RIN2 +/- DE VS HS OB5 OB4 OB3 OB2 RIN3 +/- Rsvd OB7 OB6 OG7 OG6 OR7 OR6 Current Cycle Note1: Please follow PSWG. Note2: 8-bit in Note3: R/G/B data 7:MSB, R/G/B data 0:LSB ver 0.1 18/29 M150XN07 V.2 Product Specification 6.3 Signal Description The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible . The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels. CWY20G-A0D1T (PTWO) or MSB240420 (STM) Pin No. Symbol Description 1 VDD Power Supply, 3.3V (typical) 2 VDD Power Supply, 3.3V (typical) 3 VSS Ground 4 VSS Ground 5 Rin0- - LVDS differential data input (R0-R5, G0) 6 Rin0+ + LVDS differential data input (R0-R5, G0) 7 VSS Ground 8 Rin1- - LVDS differential data input (G1-G5, B0-B1) 9 Rin1+ + LVDS differential data input (G1-G5, B0-B1) 10 VSS Ground 11 Rin2- - LVDS differential data input (B2-B5, HS, VS, DE) 12 Rin2+ + LVDS differential data input (B2-B5, HS, VS, DE) 13 VSS Ground 14 ClkIN- - LVDS differential clock input 15 ClkIN+ + LVDS differential clock input 16 VSS Ground 17 Rin3- - LVDS differential data input (R6-R7, G6-G7,B6-B7) 18 Rin3+ - LVDS differential data input (R6-R7, G6-G7,B6-B7) 19 VSS Ground 20 VSS Ground Note: Please follow PSWG. ver 0.1 19/29 M150XN07 V.2 Product Specification 6.4 Interface Timing 6.4.1 Timing Characteristics Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent. Signal Clock Timing Hsync Timing Vsync Timing Parameter Clock frequency Horizontal active Horizontal blanking Horizontal period Vertical active Vertical blanking Vertical period Symbol clk Thd Thbl Th Tvd Tvbl Tv MIN TYP 50 1024 40 1064 768 8 776 65 1024 320 1344 768 38 806 MAX 81 1024 400 1424 768 75 843 Unit MHz Tclk Tclk Tck Th Th Th Note:DE mode only Note: Typical value refer to VESA STANDARD ver 0.1 20/29 M150XN07 V.2 Product Specification 6.4.2 Timing diagram ver 0.1 21/29 M150XN07 V.2 Product Specification 6.5 Power ON/OFF Sequence Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when Vin is off. 1sec min. Vin 10% 90% 90% 0V 10% 10ms max. Signal 0V 10% 0 min. 0 min. 10% 10% Lamp On 0V 200ms ver 0.1 22/29 M150XN07 V.2 Product Specification 7.0 Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. 7.1 TFT LCD Module Connector Name / Designation Interface Connector / Interface card Manufacturer P-TWO or compatible Type Part Number CWY20G – A0G16 / MSB240420 Mating Housing Part Number HRS DF14-20S-1.25C Pin# Signal Name Pin# Signal Name 1 VDD 2 VDD 3 VSS 4 VSS 5 Rin0- 6 Rin0+ 7 VSS 8 Rin1- 9 Rin1+ 10 VSS 11 Rin2- 12 Rin2+ 13 VSS 14 ClkIN- 15 ClkIN+ 16 VSS 17 Rin3- 18 Rin3+ 19 VSS 20 VSS ver 0.1 23/29 M150XN07 V.2 Product Specification 7.2 Backlight Unit Connector Name / Designation For Lamp Connector Manufacturer JST or compatible Type / Part Number BHR-03VS-1 Mating Type / Part Number SM02(8.0)B-BHS-1-TB 7.3 Signal for Lamp connector Pin Symbol Description 1 HV Lamp High Voltage 2 NC No connection 3 LV Ground u Cable length: 140 +- 5 mm u Connector-output position: right side (front view) u Lamp assembly design shall be easy for replacement and repair. ver 0.1 24/29 M150XN07 V.2 Product Specification 8.0 Reliability Reliability test condition No Test Item Test Condition 1 Temperature Humidity Bias (THB) 50℃, 80%, 300hours 2 High Temperature Operation (HTO) 50℃, 300hours 3 Low Temperature Operation (LTO) 0℃, 300hours 4 High Temperature Storage (HTS) 60℃, 300hours 5 Low Temperature Storage (LTS) -20℃, 300hours 6 Thermal Shock Test (TST) -20℃/30min, 60℃/30min, 100 cycles 7 On/Off Test On/10sec, Off/10sec, 30,000 cycles 8 Shock Test (Non-Operating) 50G, 20ms, Half-sine wave (+ X, +Y, +Z) 9 Vibration Test (Non-Operating) 1.5G(10~200Hz P- P), 30 Minutes each Axis (X, Y, Z) 10 ESD (ElectroStatic Discharge) Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point Air Discharge: ± 15KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point 11 Altitude Test Operation:10,000 ft Non-Operation:30,000 ft 12 Drop Test The drop height is 60cm ver 0.1 25/29 M150XN07 V.2 Product Specification 9.0 Safety 9.1 Sharp Edge Requirements There will be no sharp edges or comers on the display assembly that could cause injury. 9.2 Materials 9.2.1 Toxicity There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO Toxicologist. 9.2.2 Flammability All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board. 9.3 Capacitors If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards. 10.0 Other requirement 10.1 National Test Lab Requirement The display module will satisfy all requirements for compliance to UL 1950, First Edition U.S.A. Information Technology Equipment CSA C22.2 No.950-M89 Canada, Information Technology Equipment EEC 950 International, Information Technology Equipment EN 60 950 International, Information Processing Equipment (European Norm for IEC950) 10.2 Label The label is on the panel as shown below: ver 0.1 26/29 11.0 Mechanical Characteristics Ver0.2 27/29 Ver0.2 28/29 Ver0.2 29/29