Obsolete Device 24AA174 16K 1.8V Cascadable I2C™ Serial EEPROM with OTP Security Page PACKAGE TYPES FEATURES The Microchip Technology Inc. 24AA174 is a cascadable 16K bit Electrically Erasable PROM. The device is organized as eight blocks of 256 x 8-bit memory with a 2-wire serial interface and provides a specially addressed OTP (one-time programmable) 16 byte security block. Low voltage design permits operation down to 1.8 volts (end-of-life voltage for most popular battery technologies) with standby and active currents of only 5 µA and 1 mA respectively. The 24AA174 also has a page-write capability for up to 16 bytes of data. The 24AA174 is available in the standard 8-pin DIP and 8-lead surface mount SOIC packages. 8-lead SOIC 8 VCC 7 WP 6 SCL 4 5 SDA A0 1 8 VCC A1 2 7 WP A2 3 6 SCL VSS 4 5 SDA A0 1 A1 2 A2 3 VSS 24AA174 DESCRIPTION PDIP 24AA174 • Single supply with operation down to 1.8V • 16 bytes OTP Secure Memory • Low power CMOS technology - 1 mA active current typical - 10 µA standby current typical at 5.5V - 5 µA standby current typical at 3.0V • Organized as eight blocks of 256 bytes (8 x 256 x 8) • 2-wire serial interface bus, I2C compatible • Functional address inputs for cascading up to 8 devices • Schmitt trigger, filtered inputs for noise suppression • Output slope control to eliminate ground bounce • 100 kHz (1.8V) and 400 kHz (5V) compatibility • Self-timed write cycle (including auto-erase) • Page-write buffer for up to 16 bytes • 2 ms typical write cycle time for page-write • Hardware write protect for entire memory • Can be operated as a serial ROM • Factory programming (QTP) available • ESD protection > 4,000V • 1,000,000 Erase/Write cycles guaranteed • Data retention > 200 years • 8 pin DIP, 8-lead SOIC packages • Available for commercial temperature range - Commercial (C): 0°C to +70°C BLOCK DIAGRAM A0 A1 A2 I/O CONTROL LOGIC WP MEMORY CONTROL LOGIC HV GENERATOR XDEC EEPROM ARRAY (8 x 256 x 8) PAGE LATCHES SDA SCL YDEC V CC V SS SENSE AMP R/W CONTROL The three select pins, A0, A1, and A2, function as chip select inputs and allow up to eight devices to share a common bus, for up to 128K bits total system EEPROM. I2C is a trademark of Philips Corporation. 2004 Microchip Technology Inc. DS21102G-page 1 24AA174 1.0 ELECTRICAL CHARACTERISTICS 1.1 Maximum Ratings* TABLE 1-1: Name Function Ground Serial Address/Data I/O Serial Clock Write Protect Input +1.8V to 5.5V Power Supply Chip Address Inputs VSS SDA SCL WP VCC A0, A1, A2 VCC...................................................................................7.0V All inputs and outputs w.r.t. VSS ................ -0.3V to Vcc +1.0V Storage temperature .....................................-65°C to +150°C Ambient temp. with power applied ................-65°C to +125°C Soldering temperature of leads (10 seconds) ............. +300°C ESD protection on all pins ..................................................≥ 4 kV *Notice: Stresses above those listed under “Maximum ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-2: PIN FUNCTION TABLE DC CHARACTERISTICS VCC = +1.8V to 5.5V Commercial (C): Tamb = 0°C to +70°C Parameter Symbol Min Max Units WP, SCL and SDA pins: High level input voltage Low level input voltage Hysteresis of Schmitt trigger inputs Low level output voltage Input leakage current Output leakage current Pin capacitance (all inputs/outputs) VIH VIL VHYS VOL ILI ILO CIN, COUT .7 VCC — .05 VCC — -10 -10 — — .3 VCC — .40 10 10 10 V V V V µA µA pF ICC Write ICC Read ICCS — — — — 3 1 30 100 mA mA µA µA Operating current Standby current Note: Conditions (Note) IOL = 3.0 mA, VCC = 2.5V VIN = .1V to VCC VOUT = .1V to VCC VCC = 5.0V (Note1) Tamb = 25°C, FCLK = 1 MHz VCC = 5.5V, SCL = 400 kHz VCC = 3.0V, SDA = SCL = VCC VCC = 5.5V, SDA = SCL = VCC WP=VSS This parameter is periodically sampled and not 100% tested. FIGURE 1-1: BUS TIMING START/STOP VHYS SCL THD:STA TSU:STA TSU:STO SDA START DS21102G-page 2 STOP 2004 Microchip Technology Inc. 24AA174 TABLE 1-3: AC CHARACTERISTICS Standard Mode Parameter Symbol V CC= 4.5 - 5.5V Fast Mode Min Max Min Max Units Remarks Clock frequency Clock high time Clock low time SDA and SCL rise time SDA and SCL fall time START condition hold time FCLK THIGH TLOW TR TF THD:STA — 4000 4700 — — 4000 100 — — 1000 300 — — 600 1300 — — 600 400 — — 300 300 — kHz ns ns ns ns ns START condition setup time Data input hold time Data input setup time STOP condition setup time Output valid from clock Bus free time TSU:STA 4700 — 600 — ns THD:DAT TSU:DAT TSU:STO TAA TBUF 0 250 4000 — 4700 — — — 3500 — 0 100 600 — 1300 — — — 900 — ns ns ns ns ns TOF — 250 250 ns TSP — 50 20 +0.1 CB — (Note 2) Time the bus must be free before a new transmission can start (Note 1), CB ≤ 100 pF 50 ns (Note 3) TWR — — 1M 10 — — 1M 10 — ms Cycles Output fall time from VIH min to VIL max Input filter spike suppression (SDA and SCL pins) Write cycle time Endurance (Note 1) (Note 1) After this period the first clock pulse is generated Only relevant for repeated START condition Byte or Page mode 25°C, Vcc = 5.0V, Block Mode (Note 4) 1: Not 100% tested. CB = total capacitance of one bus line in pF. 2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 3: The combined TSP and VHYS specifications are due to new Schmitt trigger inputs which provide improved noise and spike suppression. This eliminates the need for a Ti specification for standard operation. 4: This parameter is not tested but guaranteed by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on our website. FIGURE 1-2: BUS TIMING DATA TF TR THIGH TLOW SCL TSU:STA THD:DAT TSU:DAT THD:STA SDA IN TSP TSU:STO TBUF TAA TAA SDA OUT 2004 Microchip Technology Inc. DS21102G-page 3 24AA174 2.0 FUNCTIONAL DESCRIPTION The 24AA174 supports a bi-directional 2-wire bus and data transmission protocol. A device that sends data onto the bus is defined as transmitter, and a device receiving data as receiver. The bus has to be controlled by a master device which generates the serial clock (SCL), controls the bus access, and generates the START and STOP conditions, while the 24AA174 works as slave. Both, master and slave can operate as transmitter or receiver but the master device determines which mode is activated. 3.0 BUS CHARACTERISTICS The following bus protocol has been defined: • Data transfer may be initiated only when the bus is not busy. • During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in the data line while the clock line is HIGH will be interpreted as a START or STOP condition. Accordingly, the following bus conditions have been defined (see Figure 3-1). 3.1 3.4 The state of the data line represents valid data when, after a START condition, the data line is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed during the LOW period of the clock signal. There is one clock pulse per bit of data. Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of the data bytes transferred between the START and STOP conditions is determined by the master device and is theoretically unlimited, although only the last 16 will be stored when doing a write operation. When an overwrite does occur it will replace data in a first in first out fashion. 3.5 Both data and clock lines remain HIGH. 3.2 Start Data Transfer (B) A HIGH to LOW transition of the SDA line while the clock (SCL) is HIGH determines a START condition. All commands must be preceded by a START condition. 3.3 Stop Data Transfer (C) A LOW to HIGH transition of the SDA line while the clock (SCL) is HIGH determines a STOP condition. All operations must be ended with a STOP condition. FIGURE 3-1: Acknowledge Each receiving device, when addressed, is obliged to generate an acknowledge after the reception of each byte. The master device must generate an extra clock pulse which is associated with this acknowledge bit. Note: Bus not Busy (A) Data Valid (D) The 24AA174 does not generate any acknowledge bits if an internal programming cycle is in progress. The device that acknowledges, has to pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. Of course, setup and hold times must be taken into account. During reads, a master must signal an end of data to the slave by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case, the slave (24AA174) will leave the data line HIGH to enable the master to generate the STOP condition. DATA TRANSFER SEQUENCE ON THE SERIAL BUS (A) (B) (D) START CONDITION ADDRESS OR ACKNOWLEDGE VALID (D) (C) (A) SCL SDA DS21102G-page 4 DATA ALLOWED TO CHANGE STOP CONDITION 2004 Microchip Technology Inc. 24AA174 3.6 Device Addressing A control byte is the first byte received following the start condition from the master device. The first bit is always a one. The next three bits of the control byte are the device select bits (A2, A1, A0). They are used to select which of the eight devices are to be accessed. The A1 bit must be the inverse of the A1 device select pin. The next three bits of the control byte are the block select bits (B2, B1, B0). They are used by the master device to select which of the eight 256 word blocks of memory are to be accessed. These bits are in effect the three most significant bits of the word address. The last bit of the control byte defines the operation to be performed. When set to one a read operation is selected, when set to zero a write operation is selected. Following the start condition, the 24AA174 looks for the slave address for the device selected. Depending on the state of the R/W bit, the 24AA174 will select a read or write operation. Operation Read Write Control Code 1 1 FIGURE 3-2: Block Select A2 A1 A0 Block Address A2 A1 A0 Block Address CONTROL BYTE ALLOCATION START READ/WRITE SLAVE ADDRESS 1 A2 A1 A0 MSB B2 R/W A B1 B0 LSB R/W 1 0 4.0 WRITE OPERATION 4.1 Byte Write Following the start condition from the master, the device code (4 bits), the block address (3 bits), and the R/W bit which is a logic low is placed onto the bus by the master transmitter. This indicates to the addressed slave receiver that a byte with a word address will follow after it has generated an acknowledge bit during the ninth clock cycle. Therefore the next byte transmitted by the master is the word address and will be written into the address pointer of the 24AA174. After receiving another acknowledge signal from the 24AA174 the master device will transmit the data word to be written into the addressed memory location. The 24AA174 acknowledges again and the master generates a stop condition. This initiates the internal write cycle, and during this time the 24AA174 will not generate acknowledge signals (see Figure 4-1). 4.2 The write control byte, word address and the first data byte are transmitted to the 24AA174 in the same way as in a byte write. But instead of generating a stop condition the master transmits up to 16 data bytes to the 24AA174 which are temporarily stored in the on-chip page buffer and will be written into the memory after the master has transmitted a stop condition. After the receipt of each word, the four lower order address pointer bits are internally incremented by one. The higher order seven bits of the word address remains constant. If the master should transmit more than 16 words prior to generating the stop condition, the address counter will roll over and the previously received data will be overwritten. As with the byte write operation, once the stop condition is received an internal write cycle will begin (see Figure 4-2). Note: 2004 Microchip Technology Inc. Page Write Page write operations are limited to writing bytes within a single physical page, regardless of the number of bytes actually being written. Physical page boundaries start at addresses that are integer multiples of the page buffer size (or ‘page size’) and end at addresses that are integer multiples of [page size - 1]. If a page write command attempts to write across a physical page boundary, the result is that the data wraps around to the beginning of the current page (overwriting data previously stored there), instead of being written to the next page as might be expected. It is therefore necessary for the application software to prevent page write operations that would attempt to cross a page boundary. DS21102G-page 5 24AA174 FIGURE 4-1: BYTE WRITE BUS ACTIVITY: MASTER SDA LINE S T A R T BUS ACTIVITY: MASTER SDA LINE BUS ACTIVITY: 5.0 S T O P DATA S 1 A2 A1 A0 B2 B1 B0 BUS ACTIVITY: FIGURE 4-2: WORD ADDRESS CONTROL BYTE P A C K A C K A C K PAGE WRITE S T A R T S WORD ADDRESS (n) CONTROL BYTE DATA n DATA n + 1 S T O P DATA n + 15 A2 A1 A0 B2 B1 B0 P A C K ACKNOWLEDGE POLLING A C K A C K A C K FIGURE 5-1: Since the device will not acknowledge during a write cycle, this can be used to determine when the cycle is complete (this feature can be used to maximize bus throughput). Once the stop condition for a write command has been issued from the master, the device initiates the internally timed write cycle. ACK polling can be initiated immediately. This involves the master sending a start condition followed by the control byte for a write command (R/W = 0). If the device is still busy with the write cycle, then no ACK will be returned. If the cycle is complete, then the device will return the ACK and the master can then proceed with the next read or write command. See Figure 5-1 for flow diagram. A C K ACKNOWLEDGE POLLING FLOW Send Write Command Send Stop Condition to Initiate Write Cycle Send Start Send Control Byte with R/W = 0 Did Device Acknowledge (ACK = 0)? NO YES Next Operation 6.0 WRITE PROTECTION The 24AA174 can be used as a serial ROM when the WP pin is connected to VCC. Programming will be inhibited and the entire memory will be write-protected. DS21102G-page 6 2004 Microchip Technology Inc. 24AA174 7.0 READ OPERATION Read operations are initiated in the same way as write operations with the exception that the R/W bit of the slave address is set to one. There are three basic types of read operations: current address read, random read, and sequential read. 7.1 Current Address Read The 24AA174 contains an address counter that maintains the address of the last word accessed, internally incremented by one. Therefore, if the previous access (either a read or write operation) was to address n, the next current address read operation would access data from address n + 1. Upon receipt of the slave address with R/W bit set to one, the 24AA174 issues an acknowledge and transmits the eight bit data word. The master will not acknowledge the transfer but does generate a stop condition and the 24AA174 discontinues transmission (Figure 8-1). 7.2 Random Read 7.3 Sequential Read Sequential reads are initiated in the same way as a random read except that after the 24AA174 transmits the first data byte, the master issues an acknowledge as opposed to a stop condition in a random read. This directs the 24AA174 to transmit the next sequentially addressed 8-bit word (Figure 8-3). To provide sequential reads the 24AA174 contains an internal address pointer which is incremented by one at the completion of each operation. This address pointer allows an entire device memory contents to be serially read during one operation. 7.4 Noise Protection The 24AA174 employs a VCC threshold detector circuit which disables the internal erase/write logic if the VCC is below 1.5 volts at nominal conditions. The SCL and SDA inputs have Schmitt trigger and filter circuits which suppress noise spikes to assure proper device operation even on a noisy bus. Random read operations allow the master to access any memory location in a random manner. To perform this type of read operation, first the word address must be set. This is done by sending the word address to the 24AA174 as part of a write operation. After the word address is sent, the master generates a start condition following the acknowledge. This terminates the write operation, but not before the internal address pointer is set. Then the master issues the control byte again but with the R/W bit set to a one. The 24AA174 will then issue an acknowledge and transmits the eight bit data word. The master will not acknowledge the transfer but does generate a stop condition and the 24AA174 discontinues transmission (Figure 8-2). 2004 Microchip Technology Inc. DS21102G-page 7 24AA174 8.0 PIN DESCRIPTIONS 8.1 SDA Serial Address/Data Input/Output Note: Up to eight 24AA174s may be connected to the same bus. These pins must be connected to either VSS or VCC. This is a Bi-directional pin used to transfer addresses and data into and data out of the device. It is an open drain terminal, therefore the SDA bus requires a pullup resistor to VCC (typical 10KΩ for 100 kHz, 1KΩ for 400 kHz). 8.5 SCL Serial Clock This input is used to synchronize the data transfer from and to the device. 8.3 8.6 WP Security Access Write The S.A.W. data is written to the device using a normal page write following the proper control access sequence. Upon receiving the final stop bit, the internal write sequence will commence. At the completion of the internal write sequence a fuse will be set disabling the write function for the 16 byte security page. This pin must be connected to either VSS or VCC. If tied to VSS, normal memory operation is enabled (read/write the entire memory 000-7FF). If tied to VCC, WRITE operations are inhibited. The entire memory will be write-protected. Read operations are not affected. 8.7 This feature allows the user to use the 24AA174 as a serial ROM when WP is enabled (tied to VCC). 8.4 Security Access Control The security row is enabled by sending the control sequence with the I2C slave address of 0110. Bit 0 of the control byte must be set to a one for a READ OPERATION or a zero for the OTP WRITE OPERATION. The SECURITY ACCESS DATA is always read starting at byte 0 for N bytes up to and including byte 15. (See Figure 4-2). For normal data transfer SDA is allowed to change only during SCL low. Changes during SCL high are reserved for indicating the START and STOP conditions. 8.2 The level on A1 is compared to the inverse of the slave address. Security Access Read The security access read is accomplished by executing the normal read sequences, following the security access control sequence with bit 0 set to a one. The security page read starts at data byte 0. A0, A1, A2 These pins are used to configure the proper chip address in multiple-chip applications (more than one 24AA174 on the same bus). The levels on these pins are compared to the corresponding bits in the slave address. The chip is selected if the compare is true. FIGURE 8-1: CURRENT ADDRESS READ BUS ACTIVITY MASTER S T A R T SDA LINE S 1 A2 A1 A0 B2 B1 B0 CONTROL BYTE DATA n P A C K RANDOM READ S T BUS ACTIVITY A MASTER R T SDA LINE CONTROL BYTE WORD ADDRESS (n) S T A R T S 1 A2 A1A0B2B1B0 BUS ACTIVITY DS21102G-page 8 N O A C K BUS ACTIVITY FIGURE 8-2: S T O P CONTROL BYTE S T O P DATA (n) P S A C K A C K A C K N O A C K 2004 Microchip Technology Inc. 24AA174 FIGURE 8-3: SEQUENTIAL READ BUS ACTIVITY MASTER CONTROL BYTE DATA n DATA n + 1 DATA n + 2 S T O P DATA n + X P SDA LINE A C K BUS ACTIVITY A C K A C K N O A C K A C K FIGURE 8-4: SECURITY CONTROL BYTE ALLOCATION START Operation Control Code Block Select R/W Read 0110 000 1 Write 0110 000 0 READ/WRITE SLAVE ADDRESS 0 1 1 0 0 R/W 0 MSB FIGURE 8-5: A 0 LSB SECURITY PAGE READ BUS MASTER ACTIVITY S T A R T SDA LINE S 0 1 1 0 CONTROL BYTE 0 BUS ACTIVITY CONTROL BYTE S 0 1 1 0 R/W A C K BUS ACTIVITY MASTER S T A R T WORD ADDRESS (n) DATA 1 1 R/W A C K A C K DATA 2 DATA 0 A C K DATA 3 S T O P DATA 15 P SDA LINE FIGURE 8-6: A C K A C K BUS ACTIVITY A C K N O A C K A C K SECURITY PAGE WRITE BUS MASTER ACTIVITY S T A R T SDA LINE S 0 1 1 0 CONTROL BYTE BUS ACTIVITY 2004 Microchip Technology Inc. WORD ADDRESS (n) DATA (n) DATA n + 1 S T O P DATA n + 15 0 R/W A C K P A C K A C K A C K N O A C K DS21102G-page 9 24AA174 24AA174 Product Identification System To order or to obtain information, e.g., on pricing or delivery, please use the listed part numbers, and refer to the factory or the listed sales offices. 24AA174 – /P Package: Temperature Range: Device: P = Plastic DIP (300 mil Body), 8-lead SN = Plastic SOIC (150 mil Body), 8-lead Blank = 0°C to +70°C 24AA174 24AA174T 16K I2C Serial EEPROM 16K I2C Serial EEPROM (Tape and Reel) Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. Your local Microchip sales office 2. The Microchip Corporate Literature Center U.S. FAX: (602) 786-7277 3. The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. DS21102G-page 10 2004 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, MXDEV, MXLAB, PICMASTER, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, dsPICDEM, dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2004, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona and Mountain View, California in October 2003. The Company’s quality system processes and procedures are for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. 2004 Microchip Technology Inc. DS21102G-page 11 WORLDWIDE SALES AND SERVICE AMERICAS China - Beijing Singapore Corporate Office Unit 706B Wan Tai Bei Hai Bldg. No. 6 Chaoyangmen Bei Str. Beijing, 100027, China Tel: 86-10-85282100 Fax: 86-10-85282104 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: www.microchip.com China - Chengdu 3780 Mansell Road, Suite 130 Alpharetta, GA 30022 Tel: 770-640-0034 Fax: 770-640-0307 Rm. 2401-2402, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-86766200 Fax: 86-28-86766599 Boston China - Fuzhou 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 Atlanta Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 16200 Addison Road, Suite 255 Addison Plaza Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Kokomo 2767 S. Albright Road Kokomo, IN 46902 Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles 25950 Acero St., Suite 200 Mission Viejo, CA 92691 Tel: 949-462-9523 Fax: 949-462-9608 San Jose 1300 Terra Bella Avenue Mountain View, CA 94043 Tel: 650-215-1444 Fax: 650-961-0286 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 China - Hong Kong SAR Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Taiwan Kaohsiung Branch 30F - 1 No. 8 Min Chuan 2nd Road Kaohsiung 806, Taiwan Tel: 886-7-536-4816 Fax: 886-7-536-4817 Taiwan Taiwan Branch 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 Taiwan Taiwan Branch 13F-3, No. 295, Sec. 2, Kung Fu Road Hsinchu City 300, Taiwan Tel: 886-3-572-9526 Fax: 886-3-572-6459 EUROPE China - Shanghai Austria Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Durisolstrasse 2 A-4600 Wels Austria Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 China - Shenzhen Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45-4420-9895 Fax: 45-4420-9910 Rm. 1812, 18/F, Building A, United Plaza No. 5022 Binhe Road, Futian District Shenzhen 518033, China Tel: 86-755-82901380 Fax: 86-755-8295-1393 China - Shunde Room 401, Hongjian Building, No. 2 Fengxiangnan Road, Ronggui Town, Shunde District, Foshan City, Guangdong 528303, China Tel: 86-757-28395507 Fax: 86-757-28395571 China - Qingdao Rm. B505A, Fullhope Plaza, No. 12 Hong Kong Central Rd. Qingdao 266071, China Tel: 86-532-5027355 Fax: 86-532-5027205 India Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O’Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-22290061 Fax: 91-80-22290062 Japan ASIA/PACIFIC Yusen Shin Yokohama Building 10F 3-17-2, Shin Yokohama, Kohoku-ku, Yokohama, Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Australia Korea Microchip Technology Australia Pty Ltd Unit 32 41 Rawson Street Epping 2121, NSW Sydney, Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Denmark France Parc d’Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Steinheilstrasse 10 D-85737 Ismaning, Germany Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy Via Salvatore Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands Waegenburghtplein 4 NL-5152 JR, Drunen, Netherlands Tel: 31-416-690399 Fax: 31-416-690340 United Kingdom 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 07/12/04 2004 Microchip Technology Inc.