ETC 24C04AT-I/SN

24C04A
4K 5.0V I2C™ Serial EEPROM
FEATURES
DIP
8-lead
SOIC
DESCRIPTION
14-lead
SOIC
This device offers fast (1ms) byte write and
extended (-40°C to 125°C) temperature operation.
It is recommended that all other applications use
Microchip’s 24LC04B.
1
8
VCC
A1
2
7
WP
A2
3
6
SCL
VSS
4
5
SDA
A0
1
8
VCC
A1
2
7
WP
A2
3
6
SCL
VSS
4
5
SDA
NC
1
14
NC
A0
2
13
Vcc
A1
3
12
WP
NC
4
A2
5
24C04A
The Microchip Technology Inc. 24C04A is a 4K bit
Electrically Erasable PROM. The device is organized
as with a standard two wire serial interface. Advanced
CMOS technology allows a significant reduction in
power over NMOS serial devices. A special feature
provides hardware write protection for the upper half of
the block. The 24C04A has a page write capability of
up to eight bytes, and up to four 24C04A devices may
be connected to the same two wire bus.
A0
24C04A
Low power CMOS technology
Hardware write protect
Two wire serial interface bus, I2C™ compatible
5.0V only operation
Self-timed write cycle (including auto-erase)
Page-write buffer
1 ms write cycle time for single byte
1,000,000 Erase/Write cycles guaranteed
Data retention >200 years
8-pin DIP/SOIC packages
Available for extended temperature ranges
- Commercial (C):
0˚C to +70˚C
- Industrial (I):
-40˚C to +85˚C
- Automotive (E):
-40˚C to +125˚C
24C04A
•
•
•
•
•
•
•
•
•
•
•
PACKAGE TYPES
11
NC
10
SCL
Vss
6
9
SDA
NC
7
8
NC
BLOCK DIAGRAM
Vcc
Vss
Data
Buffer
(FIFO)
Data Reg.
SDA
SCL
Slave Addr.
Control
Logic
A
d
d
r
e
s
s
VPP
R/W Amp
P
o
i
n A0 to
t A7
e
r
Memory
Array
Increment
A8
A0 A1 A2 WP
I2C is a trademark of Philips Corporation.
 1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DS11183E-page 1
24C04A
1.0
ELECTRICAL CHARACTERISTICS
1.1
Maximum Ratings*
TABLE 1-1:
Name
A0
VCC...................................................................................7.0V
All inputs and outputs w.r.t. VSS ............... -0.6V to VCC +1.0V
Storage temperature ..................................... -65˚C to +150˚C
Ambient temp. with power applied................. -65˚C to +125˚C
Soldering temperature of leads (10 seconds) ............. +300˚C
ESD protection on all pins................................................4 kV
A1, A2
VSS
SDA
SCL
WP
VCC
*Notice: Stresses above those listed under “Maximum ratings”
may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any
other conditions above those indicated in the operational listings
of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
TABLE 1-2:
PIN FUNCTION TABLE
Function
No Function - Must be connected to
VCC or VSS
Chip Address Inputs
Ground
Serial Address/Data I/O
Serial Clock
Write Protect Input
+5V Power Supply
DC CHARACTERISTICS
VCC = +5V (±10%)
Commercial (C): Tamb = 0°C to +70°C
Industrial (I):
Tamb = -40°C to +85°C
Automotive (E): Tamb = -40°C to +125°C
Parameter
Symbol
Min.
Max.
Units
VCC detector threshold
SCL and SDA pins:
High level input voltage
Low level input voltage
Low level output voltage
A1 & A2 pins:
High level input voltage
Low level input voltage
Input leakage current
Output leakage current
Pin capacitance
(all inputs/outputs)
Operating current
VTH
2.8
4.5
V
VIH
VIL
VOL
VCC x 0.7
-0.3
VCC + 1
VCC x 0.3
0.4
V
V
V
VIH
VIL
ILI
ILO
CIN,
COUT
ICC
Write
ICC
Write
ICC
Read
ICCS
VCC - 0.5
-0.3
—
—
—
VCC + 0.5
0.5
10
10
7.0
V
V
µA
µA
pF
—
3.5
mA
—
4.25
mA
—
750
µA
—
100
µA
Standby current
Conditions
IOL = 3.2 mA (SDA only)
VIN = 0V to VCC
VOUT = 0V to VCC
VIN/VOUT = 0V (Note)
Tamb = +25˚C, f = 1 MHz
FCLK = 100 kHz, program cycle time = 1 ms,
Vcc = 5V, Tamb = 0˚C to +70˚C
FCLK = 100 kHz, program cycle time = 1 ms,
Vcc = 5V, Tamb = (I) and (E)
VCC = 5V, Tamb= (C), (I) and (E)
SDA=SCL=VCC=5V (no PROGRAM active)
WP/TEST = VSS, A0, A1, A2 = VSS
Note: This parameter is periodically sampled and not 100% tested
FIGURE 1-1:
BUS TIMING START/STOP
VHYS
SCL
THD:STA
TSU:STA
TSU:STO
SDA
START
DS11183E-page 2
Powered by ICminer.com Electronic-Library Service CopyRight 2003
STOP
 1998 Microchip Technology Inc.
24C04A
TABLE 1-3:
AC CHARACTERISTICS
Parameter
Symbol
Min.
Typ
Max.
Units
Clock frequency
Clock high time
Clock low time
SDA and SCL rise time
SDA and SCL fall time
START condition hold time
FCLK
THIGH
TLOW
TR
TF
THD:STA
—
4000
4700
—
—
4000
—
—
—
—
—
—
100
—
—
1000
300
—
kHz
ns
ns
ns
ns
ns
START condition setup time
TSU:STA
4700
—
—
ns
Data input hold time
Data input setup time
Data output delay time
STOP condition setup time
Bus free time
THD:DAT
TSU:DAT
TAA
TSU:STO
TBUF
0
250
300
4700
4700
—
—
—
—
—
—
—
3500
—
—
ns
ns
TI
—
—
100
ns
TWC
—
.4
.4N
—
1
N
—
ms
ms
cycles
Input filter time constant
(SDA and SCL pins)
Program cycle time
Remarks
After this period the first
clock pulse is generated
Only relevant for repeated
START condition
(Note 1)
ns
ns
Time the bus must be free
before a new transmission
can start
Byte mode
Page mode, N=# of bytes
Endurance
—
1M
25°C, Vcc = 5.0V, Block
Mode (Note 2)
Note 1: As transmitter the device must provide this internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2: This parameter is not tested but guaranteed by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on our website.
FIGURE 1-2:
BUS TIMING DATA
TR
TF
THIGH
TLOW
SCL
TSU:STA
THD:DAT
TSU:DAT
TSU:STO
THD:STA
SDA
IN
TSP
TAA
THD:STA
TAA
TBUF
SDA
OUT
 1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DS11183E-page 3
24C04A
2.0
FUNCTIONAL DESCRIPTION
The 24C04A supports a bidirectional two wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as transmitter, and a device
receiving data as receiver. The bus has to be controlled by a master device which generates the serial
clock (SCL), controls the bus access, and generates
the START and STOP conditions, while the 24C04A
works as slave. Both master and slave can operate as
transmitter or receiver but the master device determines which mode is activated.
Up to four 24C04As can be connected to the bus,
selected by A1 and A2 chip address inputs. A0 must
be tied to VCC or VSS.
3.0
BUS CHARACTERISTICS
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
is not busy.
• During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition.
Accordingly, the following bus conditions have been
defined (Figure 3-1).
3.1
Bus not Busy (A)
Both data and clock lines remain HIGH.
3.2
Start Data Transfer (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition.
All commands must be preceded by a START condition.
3.3
3.4
Data Valid (D)
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START condition
and terminated with a STOP condition. The number of
the data bytes transferred between the START and
STOP conditions is determined by the master device
and is theoretically unlimited.
3.5
Acknowledge
Each receiving device, when addressed, is obliged to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this acknowledge bit.
Note:
The 24C04A does not generate any
acknowledge bits if an internal programming cycle is in progress.
The device that acknowledges has to pull down the
SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable LOW during the HIGH
period of the acknowledge related clock pulse. Of
course, setup and hold times must be taken into
account. A master must signal an end of data to the
slave by not generating an acknowledge bit on the last
byte that has been clocked out of the slave. In this
case, the slave must leave the data line HIGH to enable
the master to generate the STOP condition.
Stop Data Transfer (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations must be ended with a STOP condition.
FIGURE 3-1:
SCL
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
(A)
(B)
(D)
START
CONDITION
ADDRESS OR
ACKNOWLEDGE
VALID
(D)
(C)
(A)
SDA
DS11183E-page 4
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DATA
ALLOWED
TO CHANGE
STOP
CONDITION
 1998 Microchip Technology Inc.
24C04A
4.0
SLAVE ADDRESS
5.0
The chip address inputs A1 and A2 must be externally
connected to either VCC or ground (VSS), thereby
assigning a unique address to each device. A0 is not
used on the 24C04A and must be connected to either
VCC or VSS. Up to four 24C04A devices may be connected to the bus. Chip selection is then accomplished
through software by setting the bits A1 and A2 of the
slave address to the corresponding hard-wired logic levels of the selected 24C04A. After generating a START
condition, the bus master transmits the slave address
consisting of a 4-bit device code (1010), followed by the
chip address bits A0, A1 and A2. The seventh bit of that
byte (A0) is used to select the upper block (addresses
100—1FF) or the lower block (addresses 000—0FF) of
the array.
BYTE PROGRAM MODE
In this mode, the master sends addresses and one
data byte to the 24C04A.
Following the START signal from the master, the device
code (4-bits), the slave address (3-bits), and the R/W
bit, which is logic LOW, are placed onto the bus by the
master. This indicates to the addressed 24C04A that a
byte with a word address will follow after it has generated an acknowledge bit. Therefore the next byte transmitted by the master is the word address and will be
written into the address pointer of the 24C04A. After
receiving the acknowledge, the master device transmits the data word to be written into the addressed
memory location. The 24C04A acknowledges again
and the master generates a STOP condition. This initiates the internal programming cycle (Figure 6-1).
The eighth bit of the slave address determines if the
master device wants to read or write to the 24C04A
(Figure 4-1).
The 24C04A monitors the bus for its corresponding
slave address all the time. It generates an acknowledge bit if the slave address was true and it is not in a
programming mode.
FIGURE 4-1:
SLAVE ADDRESS
ALLOCATION
START
READ/WRITE
SLAVE ADDRESS
1
0
1
0
A2
R/W
A1
 1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
A
A0
DS11183E-page 5
24C04A
6.0
PAGE PROGRAM MODE
as a result of only allowing the address registers bottom 3 bits to increment while the upper 5 bits remain
unchanged.
To program the master sends addresses and data to
the 24C04A which is the slave (Figure 6-1 and
Figure 6-2). This is done by supplying a START condition followed by the 4-bit device code, the 3-bit slave
address, and the R/W bit which is defined as a logic
LOW for a write. This indicates to the addressed slave
that a word address will follow so the slave outputs the
acknowledge pulse to the master during the ninth clock
pulse. When the word address is received by the
24C04A, it places it in the lower 8 bits of the address
pointer defining which memory location is to be written.
(The A0 bit transmitted with the slave address is the
ninth bit of the address pointer). The 24C04A will generate an acknowledge after every 8-bits received and
store them consecutively in a RAM (8 bytes maximum)
buffer until a STOP condition is detected. This STOP
condition initiates the internal programming cycle.. If
more than 8 bytes are transmitted by the master, the
24C04A will roll over and overwrite the data beginning
with the first received byte. This does not affect erase/
write cycles of the EEPROM array and is accomplished
FIGURE 6-1:
S
T
A
R
T
SDA LINE
S
CONTROL
BYTE
The PROGRAM cycle takes N milliseconds, whereby N
is the number of received data bytes.
WORD
ADDRESS
S
T
O
P
DATA
P
A
C
K
BUS ACTIVITY
A
C
K
A
C
K
PAGE WRITE
BUS ACTIVITY
MASTER
S
T
A
R
T
SDA LINE
S
BUS ACTIVITY
The internal, completely self-timed PROGRAM cycle
starts after the STOP condition has been generated by
the master and all received data bytes in the page
buffer will be written in a serial manner.
BYTE WRITE
BUS ACTIVITY
MASTER
FIGURE 6-2:
If the master generates a STOP condition after transmitting the first data word (Point ‘P’ on Figure 6-1), byte
programming mode is entered.
WORD
ADDRESS (n)
CONTROL
BYTE
DATA n + 1
DATA n
S
T
O
P
DATA n + 7
P
A
C
K
DS11183E-page 6
Powered by ICminer.com Electronic-Library Service CopyRight 2003
A
C
K
A
C
K
A
C
K
A
C
K
 1998 Microchip Technology Inc.
24C04A
7.0
ACKNOWLEDGE POLLING
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete (this feature can be used to maximize bus
throughput). Once the stop condition for a write command has been issued from the master, the device initiates the internally timed write cycle. ACK polling can
be initiated immediately. This involves the master sending a start condition followed by the control byte for a
write command (R/W = 0). If the device is still busy with
the write cycle, then no ACK will be returned. If the
cycle is complete, then the device will return the ACK
and the master can then proceed with the next read or
write command. See Figure 7-1 for flow diagram.
FIGURE 7-1:
8.0
WRITE PROTECTION
Programming of the upper half of the memory will not
take place if the WP pin is connected to VCC (+5.0V).
The device will accept slave and word addresses but if
the memory accessed is write protected by the WP pin,
the 24C04A will not generate an acknowledge after the
first byte of data has been received, and thus the program cycle will not be started when the STOP condition
is asserted.
ACKNOWLEDGE POLLING
FLOW
Send
Write Command
Send Stop
Condition to
Initiate Write Cycle
Send Start
Send Control Byte
with R/W = 0
Did Device
Acknowledge
(ACK = 0)?
NO
YES
Next
Operation
 1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DS11183E-page 7
24C04A
9.0
READ MODE
Note 1: If the master knows where the address
pointer is, it can begin the read sequence
at the current address (Figure 9-1) and
save time transmitting the slave and word
addresses.
In this mode the 24C04A transmits data to the master
devide.
As can be seen from Figure 9-2 and Figure 9-3, the
master first sets up the slave and word addresses by
doing a write. (Note: Although this is a read mode, the
address pointer must be written to). During this period
the 24C04A generates the necessary acknowledge
bits as defined in the appropriate section.
Note 2: In all modes, the address pointer will not
increment through a block (256 byte)
boundary, but will rotate back to the first
location in that block.
The master now generates another START condition
and transmits the slave address again, except this time
the read/write bit is set into the read mode. After the
slave generates the acknowledge bit, it then outputs
the data from the addressed location on to the SDA pin,
increments the address pointer and, if it receives an
acknowledge from the master, will transmit the next
consecutive byte. This auto-increment sequence is
only aborted when the master sends a STOP condition
instead of an acknowledge.
FIGURE 9-1:
CURRENT ADDRESS READ
BUS ACTIVITY
MASTER
S
T
A
R
T
SDA LINE
S
CONTROL
BYTE
S
T
O
P
DATA n
P
N
O
A
C
K
BUS ACTIVITY
A
C
K
FIGURE 9-2:
RANDOM READ
BUS ACTIVITY
MASTER
S
T
A
R
T
CONTROL
BYTE
S
T
A
R
T
WORD
ADDRESS (n)
S
P
A
C
K
A
C
K
BUS ACTIVITY
BUS ACTIVITY
MASTER
S
T
O
P
DATA (n)
S
SDA LINE
FIGURE 9-3:
CONTROL
BYTE
A
C
K
N
O
A
C
K
SEQUENTIAL READ
CONTROL
BYTE
DATA n
DATA n + 1
DATA n + 2
S
T
O
P
DATA n + X
P
SDA LINE
BUS ACTIVITY
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
DS11183E-page 8
Powered by ICminer.com Electronic-Library Service CopyRight 2003
 1998 Microchip Technology Inc.
24C04A
10.0
PIN DESCRIPTION
10.4
10.1
A0, A1, A2 Chip Address Inputs
This pin must be connected to either VCC or VSS. If tied
to VCC, write operations to the upper memory block will
not be executed. Read operations are possible.
A0 is not used as a chip select bit and must be tied to
either Vss or Vcc. The levels on the remaining two
address inputs(A1, A2) are compared with the corresponding bits in the slave address. The chip is selected
if the compare is true. These inputs must be connected
to either VSS or VCC.
These two address inputs allow up to four 24C04A's
can be connected to the bus
10.2
SDA Serial Address/Data Input/Output
This is a bidirectional pin used to transfer addresses
and data into and data out of the device. It is an open
drain terminal, therefore the SDA bus requires a pull-up
resistor to VCC (typical 10KΩ).
For normal data transfer, SDA is allowed to change only
during SCL LOW. Changes during SCL HIGH are
reserved for indicating the START and STOP conditions.
10.3
SCL Serial Clock
WP Write Protection
If tied to VSS, normal memory operation is enabled
(read/write the entire memory).
This feature allows the user to assign the upper half of
the memory as ROM which can be protected against
accidental programming. When write is disabled, slave
address and word address will be acknowledged but
data will not be acknowledged.
Note 1: A “page” is defined as the maximum number of bytes that can be programmed in a
single write cycle. The 24C04A page is 8
bytes long.
Note 2: A “block” is defined as a continuous area
of memory with distinct boundaries. The
address pointer can not cross the boundary from one block to another. It will however, wrap around from the end of a block
to the first location in the same block. The
24C04A has two blocks, 256 bytes each.
This input is used to synchronize the data transfer from
and to the device.
 1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DS11183E-page 9
24C04A
NOTES:
DS11183E-page 10
Powered by ICminer.com Electronic-Library Service CopyRight 2003
 1998 Microchip Technology Inc.
24C04A
24C04A Product Identification System
To order or to obtain information, e.g., on pricing or delivery, please use the listed part numbers, and refer to the factory or the listed
sales offices.
24C04A
-
/P
Package:
Temperature
Range:
P
SN
SM
SL
=
=
=
=
Plastic DIP
Plastic SOIC (150 mil Body), 8-lead
Plastic SOIC (207 mil Body), 8-lead
Plastic SOIC (150 mil Body), 14-lead
Blank = 0°C to +70°C
= -40°C to +85°C
E = -40°C to +125°C
Device:
24C04A
24C04AT
4K I2C Serial EEPROM
4K I2C Serial EEPROM (Tape and Reel)
Sales and Support
Data Sheets
Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1. Your local Microchip sales office
2. The Microchip Corporate Literature Center U.S. FAX: (602) 786-7277
3. The Microchip Worldwide Web Site (www.microchip.com)
DS11183E-page 11
Powered by ICminer.com Electronic-Library Service CopyRight 2003
 1998 Microchip Technology Inc.
WORLDWIDE SALES AND SERVICE
AMERICAS
AMERICAS (continued)
Corporate Office
Toronto
Singapore
Microchip Technology Inc.
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-786-7200 Fax: 480-786-7277
Technical Support: 480-786-7627
Web Address: http://www.microchip.com
Microchip Technology Inc.
5925 Airport Road, Suite 200
Mississauga, Ontario L4V 1W1, Canada
Tel: 905-405-6279 Fax: 905-405-6253
Microchip Technology Singapore Pte Ltd.
200 Middle Road
#07-02 Prime Centre
Singapore 188980
Tel: 65-334-8870 Fax: 65-334-8850
Atlanta
Microchip Asia Pacific
Unit 2101, Tower 2
Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong
Tel: 852-2-401-1200 Fax: 852-2-401-3431
Microchip Technology Inc.
500 Sugar Mill Road, Suite 200B
Atlanta, GA 30350
Tel: 770-640-0034 Fax: 770-640-0307
Boston
Microchip Technology Inc.
5 Mount Royal Avenue
Marlborough, MA 01752
Tel: 508-480-9990 Fax: 508-480-8575
Chicago
Microchip Technology Inc.
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 630-285-0071 Fax: 630-285-0075
Dallas
Microchip Technology Inc.
4570 Westgrove Drive, Suite 160
Addison, TX 75248
Tel: 972-818-7423 Fax: 972-818-2924
Dayton
Microchip Technology Inc.
Two Prestige Place, Suite 150
Miamisburg, OH 45342
Tel: 937-291-1654 Fax: 937-291-9175
Detroit
Microchip Technology Inc.
Tri-Atria Office Building
32255 Northwestern Highway, Suite 190
Farmington Hills, MI 48334
Tel: 248-538-2250 Fax: 248-538-2260
Los Angeles
Microchip Technology Inc.
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 949-263-1888 Fax: 949-263-1338
New York
Microchip Technology Inc.
150 Motor Parkway, Suite 202
Hauppauge, NY 11788
Tel: 631-273-5305 Fax: 631-273-5335
ASIA/PACIFIC
Hong Kong
ASIA/PACIFIC (continued)
Taiwan, R.O.C
Microchip Technology Taiwan
10F-1C 207
Tung Hua North Road
Taipei, Taiwan, ROC
Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
EUROPE
Beijing
United Kingdom
Microchip Technology, Beijing
Unit 915, 6 Chaoyangmen Bei Dajie
Dong Erhuan Road, Dongcheng District
New China Hong Kong Manhattan Building
Beijing 100027 PRC
Tel: 86-10-85282100 Fax: 86-10-85282104
Arizona Microchip Technology Ltd.
505 Eskdale Road
Winnersh Triangle
Wokingham
Berkshire, England RG41 5TU
Tel: 44 118 921 5858 Fax: 44-118 921-5835
India
Denmark
Microchip Technology Inc.
India Liaison Office
No. 6, Legacy, Convent Road
Bangalore 560 025, India
Tel: 91-80-229-0061 Fax: 91-80-229-0062
Microchip Technology Denmark ApS
Regus Business Centre
Lautrup hoj 1-3
Ballerup DK-2750 Denmark
Tel: 45 4420 9895 Fax: 45 4420 9910
Japan
France
Microchip Technology Intl. Inc.
Benex S-1 6F
3-18-20, Shinyokohama
Kohoku-Ku, Yokohama-shi
Kanagawa 222-0033 Japan
Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Arizona Microchip Technology SARL
Parc d’Activite du Moulin de Massy
43 Rue du Saule Trapu
Batiment A - ler Etage
91300 Massy, France
Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Korea
Germany
Microchip Technology Korea
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku
Seoul, Korea
Tel: 82-2-554-7200 Fax: 82-2-558-5934
Arizona Microchip Technology GmbH
Gustav-Heinemann-Ring 125
D-81739 München, Germany
Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Shanghai
Arizona Microchip Technology SRL
Centro Direzionale Colleoni
Palazzo Taurus 1 V. Le Colleoni 1
20041 Agrate Brianza
Milan, Italy
Tel: 39-039-65791-1 Fax: 39-039-6899883
Microchip Technology
RM 406 Shanghai Golden Bridge Bldg.
2077 Yan’an Road West, Hong Qiao District
Shanghai, PRC 200335
Tel: 86-21-6275-5700 Fax: 86 21-6275-5060
San Jose
Microchip Technology Inc.
2107 North First Street, Suite 590
San Jose, CA 95131
Tel: 408-436-7950 Fax: 408-436-7955
Italy
11/15/99
Microchip received QS-9000 quality system
certification for its worldwide headquarters,
design and wafer fabrication facilities in
Chandler and Tempe, Arizona in July 1999. The
Company’s quality system processes and
procedures are QS-9000 compliant for its
PICmicro® 8-bit MCUs, KEELOQ® code hopping
devices, Serial EEPROMs and microperipheral
products. In addition, Microchip’s quality
system for the design and manufacture of
development systems is ISO 9001 certified.
All rights reserved. © 1999 Microchip Technology Incorporated. Printed in the USA. 11/99
Printed on recycled paper.
Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed
by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products
as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip
logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
 1999 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003