MAXIM MAX2649EBT-T

19-2492; Rev 1; 8/03
5GHz Low-Noise Amplifier with Shutdown
Features
♦ 4.9GHz to 5.9GHz Wideband Operation
This device operates over a +2.7V to +3.6V supply
range and features low overall current consumption
(12.5mA). The MAX2649 also includes a shutdown
mode to save power when the receiver is inactive.
The LNA is designed on a low-noise, advanced SiGe
process optimized for high-frequency applications. The
device is available in a tiny 2 × 3 chip-scale package
(UCSP™) (1mm × 1.5mm).
♦ Shutdown Mode
♦ Low-Noise Figure: 2.1dB
♦ High Gain: 17dB
♦ High IIP3: 0dBm
♦ +2.7V to +3.6V Single-Supply Operation
♦ 1mm × 1.5mm UCSP
Applications
Ordering Information
IEEE802.11a Wireless LAN
PART
ETSI HiperLAN2 WLAN
MAX2649EBT-T
5GHz ISM Radios
TEMP RANGE
o
o
-40 C to +85 C
PIN-PACKAGE
2 x 3 UCSP*
*Requires special solder temperature profile described in the
Absolute Maximum Ratings section.
5GHz Cordless Phones
UCSP is a trademark of Maxim Integrated Products, Inc.
Pin Configuration appears at end of data sheet.
Functional Diagram/Typical Operating Circuit
SHUTDOWN CONTROL
TRANSMISSION LINE
RF INPUT
RFIN
GND
A1
A3
A2
BIAS
MAX2649
B1
VCC
VCC
B2
GND
B3
RFOUT
RF OUTPUT
FOR LAYOUT AND DESIGN DETAILS, PLEASE REFER TO THE MAX2649 EV KIT.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX2649
General Description
The MAX2649 high-linearity, silicon-germanium (SiGe)
low-noise amplifier (LNA) is designed for 5GHz wireless
LAN systems based on IEEE802.11a and HiperLAN2
standards. The MAX2649 achieves a 2.1dB noise figure,
17dB gain, and 0dBm IIP3, making it ideal as a firststage LNA in 5GHz OFDM WLAN radio systems.
MAX2649
5GHz Low-Noise Amplifier with Shutdown
ABSOLUTE MAXIMUM RATINGS
VCC to GND ...........................................................-0.3V to +4.2V
SHDN to GND.............................................-0.3V to (VCC + 0.3V)
RFIN to GND..........................................................-0.3V to +0.9V
RFOUT to GND...........................................-0.3V to (VCC + 0.3V)
RF Input Power (50Ω Source) ..........................................+5dBm
Continuous Power Dissipation (TA = +70°C)
2 x 3 UCSP (derate 24mW/°C above +70°C) ...............500mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Bump Temperature (soldering) (Note 1)
Infrared (15s) ...............................................................+220°C
Vapor Phase (60s) .......................................................+215°C
Note 1: This device is constructed using a unique set of packaging techniques that impose a limit on the thermal profile the device
can be exposed to during board-level solder attach and rework. This limit permits the use of only the solder profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and convection reflow.
Preheating is required. Hand or wave soldering is not recommended.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
CAUTION! ESD SENSITIVE DEVICE
DC ELECTRICAL CHARACTERISTICS
(VCC = +2.7V to +3.6V, no RF signal applied, VIH = +2.0V, VIL = +0.4V, RFIN and RFOUT terminated to 50Ω through DC-blocking
caps, TA = -40°C to +85°C. Typical values are at +3.0V and TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
Supply Voltage
VCC
Active Supply Current
ICC
Shutdown Supply Current
ICC
Digital Input Logic High
VIH
Digital Input Logic Low
VIL
CONDITIONS
MIN
TYP
MAX
UNITS
3.6
V
12.5
20
mA
0.3
10
µA
2.7
SHDN = VIL
2
V
Digital Input Current
0.4
V
5
µA
AC ELECTRICAL CHARACTERISTICS
(MAX2649 EV kit, VCC = +3.0V, PIN = -30dBm, RFIN and RFOUT terminated to 50Ω through DC-blocking caps, VIH = +2.0V, VIL = +0.4V,
TA = +25°C. Typical values are at fRF = 5250MHz, unless otherwise noted.) (Note 3)
PARAMETER
RF Frequency Range
Power Gain
SYMBOL
fRF
S21
CONDITIONS
(Note 4)
fRF = 5150MHz to 5350MHz (Note 5)
MIN
Input Third-Order Intercept Point
NF
fRF = 5150MHz to 5350MHz (Note 6)
IIP3
Two tones at 5250MHz and 5251MHz,
-30dBm per tone (Note 6)
MAX
UNITS
5900
MHz
0.2
1.5
dB
2.1
2.5
dB
4900
15
Gain Variation Over Temperature
Noise Figure
TYP
-3.5
17
dB
0
dBm
Input Return Loss
S11
-12
dB
Output Return Loss
S22
-16
dB
Reverse Isolation
S12
-30
Turn-On Time
tON
0.3
0.8
µs
Turn-Off Time
tOFF
0.5
1.2
µs
2
_______________________________________________________________________________________
dB
5GHz Low-Noise Amplifier with Shutdown
(MAX2649 EV kit, VCC = +3.0V, PIN = -30dBm, RFIN and RFOUT terminated to 50Ω through DC-blocking caps, VIH = +2.0V, VIL = +0.4V,
TA = +25°C. Typical values are at fRF = 5250MHz, unless otherwise noted.) (Note 3)
Note 2: DC characteristics are production tested at TA = +85°C. DC specifications over temperature are guaranteed by design and
characterization.
Note 3: Specifications are guaranteed by design and characterization.
Note 4: Recommended band of operation.
Note 5: Specifications are corrected for board losses on the MAX2649 EV kit (0.5dB at input, 0.5dB at output).
Note 6: Specifications are corrected for board losses on the MAX2649 EV kit (0.5dB at input).
Typical Operating Characteristics
(Data taken on board optimized for fRF = 5150MHz to 5350MHz.) (VCC = +3.0V, fRF = 5250MHz, PIN = -30dBm, and TA = +25°C,
unless otherwise noted.)
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
13
12
11
TA = +25°C
18
18
17
17
16
15
15
14
14
13
13
10
TA = -40°C
8
7
-40
SUPPLY VOLTAGE (V)
10
35
60
MAX2649 toc03
2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6
85
SUPPLY VOLTAGE (V)
IIP3 vs. SUPPLY VOLTAGE
1.0
MAX2649 toc04
-9.55
-15
TEMPERATURE (°C)
P(1dB) vs. SUPPLY VOLTAGE
-9.50
0.8
0.6
-9.60
|S11|, |S12|, |S22| vs. FREQUENCY
-9.70
-9.75
0.2
0
-0.2
-0.4
-9.80
-9.90
|S11|
-15
|S22|
-20
-25
-30
-0.6
-9.85
-5
MAGNITUDE (dB)
-9.65
0
-10
0.4
IIP3 (dBm)
OUTPUT 1dB COMPRESSION POINT (dBm)
12
12
2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6
MAX2649 toc05
9
16
MAX2649 toc06
TA = +85°C
19
GAIN (dB)
14
19
GAIN (dB)
SUPPLY CURRENT (mA)
15
20
MAX2649 toc02
16
GAIN vs. SUPPLY VOLTAGE
GAIN vs. TEMPERATURE
20
MAX2649 toc01
17
-0.8
-35
-1.0
-40
2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6
2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
|S12|
4900
5100
5300
5500
5700
5900
FREQUENCY (MHz)
_______________________________________________________________________________________
3
MAX2649
AC ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics (continued)
(Data taken on board optimized for fRF = 5150MHz to 5350MHz.) (VCC = +3.0V, fRF = 5250MHz, PIN = -30dBm, and TA = +25°C,
unless otherwise noted.)
NOISE FIGURE vs. FREQUENCY
NF (dB)
17
16
15
14
13
12
11
4900
5100
5300
5500
5700
5900
NF (dB)
18
4900
5100
OPERATING FREQUENCY (MHz)
5300
5500
5700
5900
-40
-15
10
TURN-OFF TIME
-10
OUTPUT POWER (dBm)
-20
-30
-40
-50
-60
MAX2649 toc11
0
MAX2649 toc10
-10
-20
-30
-40
-50
-60
-70
-70
0
200
400
600
TIME (ns)
800
1000
0
35
TEMPERATURE (°C)
TURN-ON TIME
OUTPUT POWER (dBm)
3.9
3.7
3.5
3.3
3.1
2.9
2.7
2.5
2.3
2.1
1.9
1.7
1.5
1.3
1.1
0.9
OPERATING FREQUENCY (MHz)
0
4
NOISE FIGURE vs. TEMPERATURE
MAX2649 toc08
MAX2649 toc07
19
4.0
3.8
3.6
3.4
3.2
3.0
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
MAX2649 toc09
|S21| vs. FREQUENCY
20
|S21| (dB)
MAX2649
5GHz Low-Noise Amplifier with Shutdown
200
400
600
800
1000
TIME (ns)
_______________________________________________________________________________________
60
85
5GHz Low-Noise Amplifier with Shutdown
PIN
NAME
FUNCTION
A1
RFIN
LNA Input. Requires shunt capacitor and transmission line for input matching. (See the Typical
Operating Circuit and refer to the MAX2649 EV kit data sheet for details.)
A2, B2
GND
Ground. For optimum performance, provide a low-inductance connection to the ground plane.
A3
SHDN
Shutdown. Apply logic signal through 100Ω resistor with a 20pF shunt capacitor to ground. Set
SHDN high for active operation. Set SHDN low to place the part in shutdown mode.
B1
VCC
B3
RFOUT
+2.7V to +3.6V Supply Pin. Bypass with 100pF capacitor. (See the Typical Operating Circuit and
refer to the MAX2649 EV kit data sheet for details.)
LNA Output. Requires external matching network for optimal performance. (See the Typical
Operating Circuit and refer to the MAX2649 EV kit data sheet for details.)
Detailed Description
The MAX2649 LNA operates with RF frequencies of
4.9GHz to 5.9GHz. This device is ideal for IEEE802.11a
and HiperLAN2 applications. This device is available in
a 6-bump UCSP package and contains internal bias
circuitry and shutdown circuitry to minimize the number
of required external components.
Applications Information
Optimal gain and noise-figure performance require
input- and output-matching circuits tuned for the band of
interest. All electrical specifications and typical operating
characteristics are measured on the MAX2649 evaluation kit (EV kit), which is tuned for operation in the
5.15GHz to 5.35GHz band. Referencing the application
circuit, PC board layout, and components specified in
the MAX2649 EV kit data sheet reduces evaluation and
design time for five system designs. For applications in
other bands, refer to the MAX2649 S-parameters, noise
parameters, and the following comments to aid design.
The S-parameters and noise parameters are available at
www.maxim-ic.com.
Input Matching
The input stage is internally biased, so no external bias
circuitry is required at RFIN. Be sure to AC-couple to
the input. Because the noise figure of the LNA design is
severely degraded by low-Q matching components,
always design with high-Q wire-wound inductors and
low-loss capacitors. Remember that package parasitics
must be taken into consideration; always use components with self-resonant frequencies higher than the
intended frequency of operation.
Output Matching
The output of the MAX2649 is an open-collector transistor; the DC bias and RF matching network are off-chip, as
illustrated in the Typical Operating Circuit. Bias the output
stage with VCC through an RF choke. The collector is in
series with a small inductor and then AC-coupled to the
RF output. If necessary, place a shunt capacitor to
ground at the far end of the inductor to provide better
matching. S-parameters and noise parameters can be
found at www.maxim-ic.com.
Power-Supply Bypassing
Proper power-supply bypassing is essential for highfrequency circuit stability. Place a small-value capacitor
as close to the IC as possible to decouple high-frequency noise. Place a larger-value capacitor near the supply
to decouple low-frequency noise. Whenever possible,
place the ground-connected side of bypass capacitors
within a few millimeters of the IC’s ground connections.
_______________________________________________________________________________________
5
MAX2649
Pin Description
MAX2649
5GHz Low-Noise Amplifier with Shutdown
Layout information
A properly designed PC board is an essential part of
any RF/microwave circuit. Keep RF signal lines as short
as possible to reduce losses, EMI, and stray inductance. Use multiple, separate low-inductance-plated
vias to the ground plane for each ground bump.
The chip-scale package (UCSP) has a bump pitch of
0.5mm (19.7mil) and a bump diameter of 0.3mm
(12mil). Therefore, lay out the solder pad spacing on
0.5mm (19.7mil) centers, and use a pad size of
0.25mm (10mil), and a solder mask opening of 0.33mm
(13mil). Round or square pads are permissible. Refer to
the Maxim application note, Wafer Level Chip-Scale
Packaging, for additional detailed information on UCSP
layout and handling.
UCSP Reliability
The chip-scale package (UCSP) represents a unique
package that greatly reduces board space compared to
other packages. UCSP reliability is integrally linked to
the user’s assembly methods, circuit board material,
and usage environment. Operating life test and moisture
resistance remains uncompromised, as it is primarily
determined by the wafer-fabrication process. Mechanical stress performance is a greater consideration for a
UCSP. UCSP solder-joint contact integrity must be considered because the package is attached through direct
solder contact to the user’s PC board. Testing done to
characterize the UCSP reliability performance shows
that it is capable of performing reliably through environmental stresses. Results of environmental stress tests
and additional usage data and recommendations are
detailed in the UCSP application note, which can be
found on Maxim’s website, www.maxim-ic.com/
1st_pages/UCSP.htm.
Chip Information
Pin Configuration
TRANSISTOR COUNT: 471
TOP VIEW
6
B1
A1
VCC
RFIN
B2
A2
GND
GND
B3
A3
RFOUT
SHDN
_______________________________________________________________________________________
5GHz Low-Noise Amplifier with Shutdown
6L, UCSP.EPS
PACKAGE OUTLINE, 3x2 UCSP
21-0097
G
1
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
7 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
MAX2649
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)